Dell Latitude 10 – ST2 Owner's Manual Regulatory Model: T05G Regulatory Type: T05G001
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2013 Dell Inc.
Contents Notes, Cautions, and Warnings...................................................................................................2 1 Working on Your Computer.......................................................................................................5 Before Working Inside Your Computer.....................................................................................................................5 Turning Off Your Computer...............................................................
Installing the Docking Board..................................................................................................................................23 Removing the System Board...................................................................................................................................23 Installing the System Board....................................................................................................................................24 Removing the Rear Camera......
Working on Your Computer 1 Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes that the following conditions exist: • You have performed the steps in Working on Your Computer. • You have read the safety information that shipped with your computer.
NOTE: To avoid damaging the system board, you must remove the main battery before you service the computer. 7. Remove the main battery. 8. Turn the computer top-side up. 9. Press the power button to ground the system board. CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before opening the display.
Overview 2 Your Dell Latitude 10-ST2 tablet is built for business with easy management and security. It provides: • world class security • easy management • long term stability It is shipped with Windows 8 operating system to fully utilize the touch experience. NOTE: It is recommended that you immediately backup the operating system image using the USB device through Dell Backup and Recovery (DBAR) application.
Using a Stylus in a Tablet The stylus allows you to actively navigate through the menus. You can use it as a mouse and also as a pen. Using the Stylus as a Mouse You can use the stylus the same way you use a mouse or touch pad with a notebook computer. Holding the stylus near the display makes a small cursor appear. Moving the stylus moves the cursor. Table 1 describes how to use the stylus. Table 1.
2. Go to Folder options. 3. Click View. 4. Under Advanced settings , select the Use check boxes to select items check box, and then click OK. Entering Text You can use handwriting recognition application or the touch keyboard to enter text. Table 2. Input Panel Icons Icon Name Function The touch keyboard is like a standard keyboard, you can enter text by tapping the keys with your stylus or finger.
Pen and Touch Settings Using the stylus, you can adjust how quickly you tap the screen when you double-tap the screen. It also allows you define the spatial tolerance. The Press and Hold settings allow you to define the speed and the duration for a right-click action.
Touch Usage One of the key advantages of the Tablet PC is the ability to easily switch from pen input to touch input. When you use Touch Mode , a translucent image of a computer mouse, called the touch pointer, floats beneath your finger. The touch pointer has left and right mouse buttons that you can tap with your finger. You use the area beneath the buttons to drag the touch pointer. To show the touch pointer, go to Control Panel → Pen and Touch and clicking on the Touch tab.
Removing and Installing Components 3 This section provides detailed information on how to remove or install the components from your computer. Recommended Tools The procedures in this document may require the following tools: • Small flat-blade screwdriver • #0 Phillips screwdriver • #1 Phillips screwdriver • Small plastic scribe Internal and External View Figure 1. External View 1. 2. 3. 4. 5.
Figure 2. Internal View 1. 2. 3. 4. 5. docking board coin-cell battery speaker system board front camera 6. rear camera 7. SmartCard reader/WWAN card (WWAN card is located below the SmartCard reader Removing the Battery 1. Follow the procedures in Before Working Inside Your Computer. 2. Slide the battery release latch to the unlock position. Lift up the battery in an outward direction and remove it from the computer.
Installing the Battery 1. Slide the battery into its slot until it clicks into place. 2. Follow the procedures in After Working Inside Your Computer. Removing the Base Cover 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the battery. 3. Remove the screws that secure the base cover to the computer.
4. Pry and release the tabs that secure the base cover by following the arrow sequence in the diagram. 5. Pry and lift the tabs that secure the base cover in the battery bay area in an upward direction. Pry and flip the base cover.
6. Lift the retention clasp in an upward direction and release the fingerprint reader cable outward to remove it from the system board. Lift the base cover away from the computer. Installing the Base Cover 1. Attach the fingerprint reader flex cable from the base cover to the system board. 2. Attach the base cover to the computer. 3. Push the edges of the base cover into the securing clips until they are fully engaged. 4. Tighten the screws to secure the base cover. 5. Install the battery. 6.
Installing the Front Camera 1. Place the camera module in its slot on the computer. 2. Tighten the screw to secure the camera module to the computer. 3. Connect the camera cable to the connector. 4. Install the: a) base cover b) battery 5. Follow the procedures in After Working Inside Your Computer. Removing the Speakers 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the : a) battery b) base cover 3.
5. Un-route the speaker cables on the right-hand side of the computer and lift up to release the right speaker from the computer. 6. Un-route the speaker cables on the left-hand side of the computer and lift up to release the left speaker from the computer.
Installing the Speakers 1. Place the right and the left speakers in their slot. 2. Route the speaker cables on the chassis. 3. Tighten the screws to secure the speakers to the chassis. 4. Place the coin-cell battery in its slot and route the cables. 5. Connect the speaker connector cable to its port on the system board. 6. Install the : a) base cover b) battery 7. Follow the procedures in After Working Inside Your Computer.
Installing the SmartCard Reader 1. Place the SmartCard reader into its slot. 2. Tighten the screws to secure the SmartCard reader to the system board. 3. Install the : a) base cover b) battery 4. Follow the procedures in After Working Inside Your Computer. Removing the Wireless Wide Area Network (WWAN) Card NOTE: The WWAN Card is an optional component. 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the : a) battery b) base cover c) SmartCard reader 3.
4. Disconnect the screws that secure the WWAN card to the system board and lift it up to remove it from the computer. Installing the Wireless Wide Area Network (WWAN) Card 1. Slide the WWAN card into the slot. 2. Tighten the screws to secure the WWAN card to the computer. 3. Connect the system board side data cable to the WWAN card. 4. Connect the antennae according to the color code on the WWAN card. 5. Install the : a) SmartCard reader b) base cover c) battery 6.
5. Remove the docking board from the computer and disconnect the home-button board cable. Installing the Docking Board 1. Connect the home-button board cable to the docking board and place the docking board in its slot in the computer. 2. Tighten the screws to secure the docking board to the computer. 3. Connect the docking board power flex cable to the connector. 4. Install the: a) b) c) d) e) f) 5.
f) front camera g) docking board 3. Disconnect the LVDS and docking board flex cables. 4. Remove the screws that secure the system board to the computer. 5. Lift up the system board at a 45° angle and pull it away from the computer. Installing the System Board 1. Place the system board in its compartment on the computer. 2. Tighten the screws to secure the system board to the computer. 3.
e) SmartCard reader f) base cover g) battery 4. Follow the procedures in After Working Inside Your Computer. Removing the Rear Camera 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the: a) battery b) base cover c) SmartCard reader d) WWAN Card e) speaker f) front camera g) system board 3. Remove the camera module from the system board. Installing the Rear Camera 1. Place the camera module in its slot on the system board. 2.
3. Follow the procedures in After Working Inside Your Computer. Removing the Coin-Cell Battery 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the: a) b) c) d) e) f) g) 3. battery base cover SmartCard reader WWAN Card speaker front camera system board Disconnect the coin-cell battery cable and remove it from the system board. Installing the Coin-Cell Battery 1. Connect the coin-cell battery cable to the system board. 2.
5. Follow the procedures in After Working Inside Your Computer.
System Setup 4 System Setup enables you to manage your computer hardware and specify BIOS‐level options.
Keystroke Action connected to an optional external USB keyboard) On Screen Mouse Pointer Use this to navigate the System Setup by using your finger or an interactive pen. Apply Icon Save current configuration. Defaults Icon Load setup defaults. Exit Icon Exits System Setup. Boot Menu Press when the Dell logo appears to initiate a one-time boot menu with a list of the valid boot devices for the system. Hard Drive Network Diagnostics and Enter Setup options are included in this menu.
Table 5. Boot Sequence Option Function File Browser Add Boot Option Displays the order that the BIOS searches devices when trying to find an operating system to boot. A new device can be added here. File Browser Del Boot Option A displayed boot device can be removed from the boot order. Table 6. Date/Time Option Function System Date Displays the system date. System Time Displays the system time. Table 7.
Option Description Click OK after entering the password details. System Password Allows you to set, change, or delete the computer password (previously called the primary password). The drive does not have a password set by default. To add a new password: • • • Enter the old password Enter the new password Confirm the new password Click OK after entering the password details. Strong Password Enable strong password - This option is disabled by default.
Option Description Admin Setup Lockout Allows you to enable or disable the option to enter setup when an admin password is set. • Enable Admin Setup Lockout (Default) Table 10. Secure Boot Option Function Secure Boot Enables or Disables the secure boot feature. Default : Disabled Expert Key Management Allows you to manage all secure boot keys. Table 11. Performance Option Description Multi Core Support Specifies whether the process will have one or all cores enabled.
Option Description • • Disabled - Does not allow the system to power on by special LAN signals when it receives a wake-up signal from the LAN or wireless LAN. (Default ) LAN Only - Allows the system to be powered on by special LAN signals. Table 13. POST Behaviour Option Description Adapter Warnings Allows you to activate the adapter warning messages when certain power adapters are used. The option is enabled by default.
Troubleshooting Your Computer 5 You can troubleshoot your computer using indicators like Diagnostic Lights, Beep Codes, and Error Messages during the operation of the computer. Enhanced Pre-boot System Assessment (ePSA) The ePSA is a diagnostic utility available on your computer. This utility includes a series of tests for a computer's hardware. You can run these tests even if the computer lacks any media (hard drive, optical drive, etc.).
3. During the testing process, you will be prompted to answer a YES or NO question. To respond, press Volume Up = YES or Volume Down = NO. 4. Press the Security Button ( + + ) to click OK once the tests are completed. 5. The volume up and down buttons can also be used as the key when switching between options. Beep Codes The computer may emit a series of beeps during start-up if the display cannot show errors or problems.
Code Cause and Troubleshooting Steps 1 BIOS ROM checksum in progress or failure System board failure, covers BIOS corruption or ROM error 2 No RAM detected No memory detected 3 Chipset Error (North and South Bridge Chipset, DMA/IMR/ Timer Error) , Time-Of-Day Clock test failure , Gate A20 failure , Super I/O chip failure , Keyboard controller test failure System board failure 4 RAM Read/Write failure Memory failure 5 Real-time clock power fail CMOS battery failure 6 Video BIOS test failure Vide
Code Cause and Troubleshooting Steps CMOS battery failure 6 Video BIOS test failure Video card failure 7 CPU - cache test failure Processor failure 8 Display Display failure Troubleshooting the Wacom Digitizer The Wacom Tablet Settings applet is used to adjust several settings for the digitizer. Once the Wacom drivers are loaded, an icon appears in the system tray. Troubleshooting Steps 1. Check the system information to see how many touch points are detected.
6 Specifications NOTE: Offerings may vary by region. The following specifications are only those required by law to ship with your computer. For more information regarding the configuration of your computer, click Start → Help and Support and select the option to view information about your computer.
Communications Network adapter USB 2.0 based Gigabit LAN via dock Wireless mobile broadband card (optional) Ports and Connectors Audio one microphone-in and stereo headphones/speakers combo connector Video one mini HDMI connector USB one USB 2.0 connector Memory card reader one 3-in-1 memory card reader Display Type HD IPS LED Size 10.1 inches high definition (HD) Dimensions: Height 125.11 mm (4.93 inches) Width 222.52 mm (8.76 inches) Diagonal 255.28 mm (10.
Battery Temperature range Operating 0 °C to 50 °C (32° F to 158 °F) 0 °C to 50 °C (32 °F to 158 °F) Non-Operating -20 °C to 65 °C ( –4 °F to 149 °F) -20 °C to 65 °C ( –4 °F to 149 °F) Coin-cell battery 3 V CR2025 lithium ion AC Adapter Type Input voltage 100 VAC to 240 VAC Input current (maximum) 0.87 A Input frequency 50 Hz to 60 Hz Output power 30 W Output current (30 W) 1.54 A Rated output voltage 19 Vdc/1.58 A; 19.5 Vdc/1.
Contacting Dell 7 NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be available in your area. To contact Dell for sales, technical support, or customer service issues: 1. Visit dell.com/support 2. Select your support category. 3.
