Reference Guide

ManualsBrandsDell ManualsComputer equipmentForce10 Z9000

Dell Command Line Reference Guide for the

Z9000 System

9.4(0.0)

Summary of content (1653 pages)

PAGE 1
Dell Command Line Reference Guide for the Z9000 System 9.4(0.
PAGE 2
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Copyright © 2014 Dell Inc. All rights reserved. This product is protected by U.S. and international copyright and intellectual property laws.
PAGE 3
Contents 1 About this Guide......................................................................................................41 Objectives............................................................................................................................................ 41 Audience.............................................................................................................................................. 41 Conventions.............................................................
PAGE 4
clear alarms......................................................................................................................................... 88 clear command history.......................................................................................................................89 clear line.............................................................................................................................................. 89 configure...................................................
PAGE 5
show processes ipc flow-control.....................................................................................................132 show software ifm.............................................................................................................................133 show system...................................................................................................................................... 135 show tech-support...............................................................
PAGE 6
ip access-group........................................................................................................................... 177 ip control-plane egress-filter......................................................................................................179 show ip accounting access-list...................................................................................................179 Standard IP ACL Commands............................................................................
PAGE 7
seq................................................................................................................................................237 show config.................................................................................................................................239 show ip prefix-list detail..............................................................................................................239 show ip prefix-list summary..................................................
PAGE 8
deny udp (for Extended IP ACLs)......................................................................................................279 deny arp (for Extended MAC ACLs)..................................................................................................280 deny icmp (for Extended IP ACLs).................................................................................................... 281 deny ether-type (for Extended MAC ACLs).................................................................
PAGE 9
bfd all-neighbors............................................................................................................................... 331 bfd disable......................................................................................................................................... 333 bfd enable (Configuration)............................................................................................................... 333 bfd enable (Interface)..............................................
PAGE 10
clear ip bgp.................................................................................................................................. 371 clear ip bgp dampening.............................................................................................................. 373 clear ip bgp flap-statistics...........................................................................................................374 clear ip bgp peer-group..................................................................
PAGE 11
neighbor update-source.............................................................................................................414 neighbor weight.......................................................................................................................... 415 network........................................................................................................................................416 network backdoor........................................................................
PAGE 12
show ip bgp ipv4 extcommunity-list......................................................................................... 469 show ip bgp paths extcommunity..............................................................................................470 show ip extcommunity-list......................................................................................................... 471 show running-config extcommunity-list...................................................................................
PAGE 13
hardware watchdog....................................................................................................................504 show hardware layer2................................................................................................................ 504 show hardware layer3.................................................................................................................505 show hardware stack-unit.............................................................................
PAGE 14
ip dhcp source-address-validation............................................................................................ 540 ip dhcp snooping vlan................................................................................................................ 540 ip dhcp relay information-option............................................................................................... 541 ip dhcp relay information-agent remote-id.......................................................................
PAGE 15
garp timers........................................................................................................................................ 580 gvrp enable........................................................................................................................................582 gvrp registration................................................................................................................................582 protocol gvrp...............................................
PAGE 16
show ip igmp snooping mrouter................................................................................................ 617 21 Interfaces.............................................................................................................. 619 Basic Interface Commands.............................................................................................................. 619 clear counters....................................................................................................
PAGE 17
speed (Management interface).................................................................................................. 680 stack-unit portmode................................................................................................................... 681 switchport................................................................................................................................... 682 Egress Interface Selection (EIS) Commands.......................................................
PAGE 18
arp...................................................................................................................................................... 719 arp backoff-time............................................................................................................................... 720 arp learn-enable................................................................................................................................ 721 arp max-entries..........................................
PAGE 19
show ip cam stack-unit.................................................................................................................... 770 show ip fib linecard........................................................................................................................... 772 show ip fib stack-unit........................................................................................................................774 show ip flow...............................................................
PAGE 20
show ipv6 flowlabel-zero................................................................................................................. 821 show ipv6 interface.......................................................................................................................... 822 show ipv6 mld_host......................................................................................................................... 825 show ipv6 route.................................................................
PAGE 21
isis ipv6 metric.................................................................................................................................. 863 isis metric.......................................................................................................................................... 864 isis network point-to-point.............................................................................................................. 865 isis password....................................................
PAGE 22
hg-link-bundle-monitor trigger-threshold ....................................................................................908 hg-link-bundle-monitor rate-interval............................................................................................. 908 show hg-link-bundle-distribution................................................................................................... 909 snmp-server enable traps (for High-Gigabit Port Channel).........................................................
PAGE 23
fefd-global................................................................................................................................... 951 show fefd.....................................................................................................................................952 29 Link Layer Discovery Protocol (LLDP).......................................................... 955 LLPD Commands.......................................................................................................
PAGE 24
clear ip msdp sa-cache.................................................................................................................... 988 clear ip msdp statistic....................................................................................................................... 989 debug ip msdp..................................................................................................................................990 ip msdp cache-rejected-sa..................................................
PAGE 25
show ip mroute......................................................................................................................... 1027 show ip rpf................................................................................................................................ 1030 IPv6 Multicast Commands............................................................................................................. 1030 debug ipv6 mld_host.....................................................................
PAGE 26
network area............................................................................................................................. 1065 passive-interface.......................................................................................................................1067 redistribute................................................................................................................................ 1069 redistribute bgp..................................................................
PAGE 27
ipv6 ospf cost.............................................................................................................................1125 ipv6 ospf dead-interval............................................................................................................. 1126 ipv6 ospf encryption.................................................................................................................. 1127 ipv6 ospf graceful-restart helper-reject..................................................
PAGE 28
ip pim sparse-mode.................................................................................................................. 1166 ip pim sparse-mode sg-expiry-timer....................................................................................... 1167 ip pim spt-threshold..................................................................................................................1168 no ip pim snooping dr-flood.................................................................................
PAGE 29
private-vlan mode...........................................................................................................................1207 private-vlan mapping secondary-vlan...........................................................................................1208 switchport mode private-vlan........................................................................................................1209 39 Per-VLAN Spanning Tree Plus (PVST+)........................................................
PAGE 30
policy-map-output................................................................................................................... 1246 qos-policy-input....................................................................................................................... 1247 qos-policy-output.................................................................................................................... 1248 queue egress..................................................................................
PAGE 31
ip rip receive version.......................................................................................................................1290 ip rip send version........................................................................................................................... 1291 ip split-horizon................................................................................................................................1292 maximum-paths........................................................
PAGE 32
show config.....................................................................................................................................1333 show spanning-tree rstp.................................................................................................................1333 spanning-tree rstp.......................................................................................................................... 1336 tc-flush-standard...........................................................
PAGE 33
radius-server host......................................................................................................................1375 radius-server key....................................................................................................................... 1377 radius-server retransmit............................................................................................................1379 radius-server timeout.......................................................................
PAGE 34
ip ssh server vrf.......................................................................................................................... 1413 ip ssh source-interface............................................................................................................. 1414 ip ssh vrf..................................................................................................................................... 1415 show crypto.....................................................................
PAGE 35
show snmp................................................................................................................................ 1452 show snmp engineID................................................................................................................ 1453 show snmp group..................................................................................................................... 1453 show snmp user.................................................................................
PAGE 36
50 Stacking..............................................................................................................1503 redundancy disable-auto-reboot.................................................................................................. 1503 redundancy force-failover stack-unit............................................................................................1504 redundancy protocol....................................................................................................
PAGE 37
clock summer-time date................................................................................................................1544 clock summer-time recurring........................................................................................................1546 clock timezone............................................................................................................................... 1548 clock update-calendar.....................................................................
PAGE 38
56 Virtual Link Trunking (VLT)............................................................................ 1587 back-up destination........................................................................................................................ 1587 clear vlt statistics.............................................................................................................................1588 delay-restore............................................................................................
PAGE 39
show run vrf.................................................................................................................................... 1623 59 Virtual Router Redundancy Protocol (VRRP)............................................1625 IPv4 VRRP Commands....................................................................................................................1625 advertise-interval...............................................................................................................
PAGE 40
PAGE 41
About this Guide 1 This book provides information about the Dell Networking OS command line interface (CLI). This book also includes information about the protocols and features found in Dell Z-Series platform.
PAGE 42
[X] Keywords and parameters within brackets are optional. x|y Keywords and parameters separated by a bar require you to choose one option. x||y Keywords and parameters separated by a double bar allows you to choose any or all of the options. Information Icons This book uses the following information symbols: NOTE: The Note icon signals important operational information. CAUTION: The Caution icon signals information about situations that could result in equipment damage or loss of data.
PAGE 43
CLI Basics 2 This chapter describes the command line interface (CLI) structure and command modes. The Dell Networking operating software commands are in a text-based interface that allows you to use the launch commands, change command modes, and configure interfaces and protocols. Accessing the Command Line When the system boots successfully, you are positioned on the command line in EXEC mode and not prompted to log in. You can access the commands through a serial console port or a Telnet session.
PAGE 44
When another user enters CONFIGURATION mode, Dell Networking OS sends a message similar to the following: % Warning: User "admin" on line vty2 "172.16.1.210" is in configuration In this case, the user is “admin” on vty2. Obtaining Help As soon as you are in a command mode there are several ways to access help. To obtain a list of keywords at any command mode: Type a ? at the prompt or after a keyword. There must always be a space before the ?.
PAGE 45
tacacs telnet tftp trace-group trace-list Dell(conf)#ip Interface configuration for TACACS+ Specify telnet options TFTP configuration commands Named trace-list Named trace-list When entering commands, you can take advantage of the following timesaving features: • The commands are not case-sensitive. • You can enter partial (truncated) command keywords. For example, you can enter interface teng 0/0 for the interface tengigabitethernet 0/0 command. • To complete keywords in commands, use the TAB key.
PAGE 46
Navigating the CLI Dell Networking OS displays a CLI prompt comprised of the host name and CLI mode. • Host name is the initial part of the prompt and is “Dell” by default. You can change the host name with the hostname command. • CLI mode is the second part of the prompt and reflects the current CLI mode. For a list of the Dell Networking OS command modes, refer to the command mode list in the Accessing the Command Line section.
PAGE 47
show run | grep ethernet does not return the previous search result because it only searches for instances containing a noncapitalized “ethernet” show run | grep Ethernet ignore-case returns instances containing both “Ethernet” and “ethernet” no-more does not paginate the display output save copies the output to a file for future use Displaying All Output To display the output all at once (not one screen at a time), use the no-more option after the pipe.
PAGE 48
Based on whether VRF feature is identified as supported in the Feature Configuration file, configuration command feature vrf becomes available for usage. This command will be stored in running-configuration and will precede all other VRF-related configurations. NOTE: The MXL and Z9000 platforms currently do not support VRF. These platforms support only the management and default VRFs, which are available by default. As a result, the feature vrf command is not available for these platforms.
PAGE 49
Usage Information You can activate VRF application on a device by using the feature vrf command in CONFIGURATION mode. The no feature vrf command is not supported on any of the platforms. Example Dell#show feature Feature State -----------------------------VRF enabled Command Modes To navigate and launch various CLI modes, use specific commands. Navigation to these modes is described in the following sections. BGP ADDRESS-FAMILY Mode To enable or configure IPv4 for BGP, use BGP ADDRESS-FAMILY mode.
PAGE 50
CONTROL-PLANE Mode To manage control-plane traffic, use CONTROL-PLANE mode. For more information, refer to Control Plane Policing (CoPP). To enter CONTROL-PLANE mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the control-plane-cpuqos command. The prompt changes to include (conf-controlcpuqos). You can return to CONFIGURATION mode by using the exit command. DHCP Mode To enable and configure Dynamic Host Configuration Protocol (DHCP), use DHCP mode.
PAGE 51
To enter EIS mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the management egress-interface-selection command. The prompt changes to include (conf-mgmt-eis). You can return to CONFIGURATION mode by using the exit command. EXEC Mode When you initially log in to the switch, by default, you are logged in to EXEC mode. This mode allows you to view settings and enter EXEC Privilege mode, which is used to configure the device.
PAGE 52
GRUB Mode To enable GRUB mode, press ESC when the following message appears during a system boot: Press ESC key to stop autoreboot.... Select Force10 Boot using the arrow keys and then press the “C” key to enter the GRUB Command Line Interface. The command prompt changes to grub>. INTERFACE Mode Use INTERFACE mode to configure interfaces or IP services on those interfaces. An interface can be physical (for example, a Gigabit Ethernet port) or virtual (for example, the Null interface).
PAGE 53
To enter IP ACCESS LIST mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Use the ip access-list standard or ip access-list extended command. Include a name for the ACL. The prompt changes to include (conf-std-nacl) or (conf-ext-nacl). You can return to CONFIGURATION mode by using the exit command. ISIS ADDRESS-FAMILY Mode To enable or configure IPv6 for ISIS, use ISIS ADDRESS-FAMILY mode. For more information, refer to Intermediate System to Intermediate System (IS-IS).
PAGE 54
To enter MAC ACCESS LIST mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Use the mac access-list standard or mac access-list extended command. Include a name for the ACL. The prompt changes to include (conf-std-macl) or (conf-ext-macl). You can return to CONFIGURATION mode by using the exit command. MONITOR SESSION Mode To enable and configure a traffic monitoring session using port monitoring, use MONITOR SESSION mode. For more information, refer to Port Monitoring.
PAGE 55
PORT-CHANNEL FAILOVER-GROUP Mode To configure shared LAG state tracking, use PORT-CHANNEL FAILOVER-GROUP mode. For more information, refer to Port Channel Commands. To enter PORT-CHANNEL FAILOVER-GROUP mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the port-channel failover-group command. The prompt changes to include (conf-pofailover-grp). You can return to CONFIGURATION mode by using the exit command. PREFIX-LIST Mode To configure a prefix list, use PREFIX-LIST mode.
PAGE 56
2. Use the route-map map-name [permit | deny] [sequence-number] command. The prompt changes to include (config-route-map). You can return to CONFIGURATION mode by using the exit command. ROUTER BGP Mode To enable and configure Border Gateway Protocol (BGP), use ROUTER BGP mode. For more information, refer to Border Gateway Protocol IPv4 (BGPv4) To enter ROUTER BGP mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Use the router bgp command then enter the AS number.
PAGE 57
ROUTER RIP Mode To enable and configure Router Information Protocol (RIP), use ROUTER RIP mode. For more information, refer to Routing Information Protocol (RIP). To enter ROUTER RIP mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the router rip command. The prompt changes to include (conf-router_rip). You can return to CONFIGURATION mode by using the exit command. SPANNING TREE Mode To enable and configure the Spanning Tree protocol, use SPANNING TREE mode.
PAGE 58
1. To enable VRRP globally, verify that you are logged in to CONFIGURATION mode. 2. Enter the vrrp-group command then enter the VRRP group ID. The prompt changes to include (conf-if-interface-type-slot/port-vrid-vrrp-group-id).
PAGE 59
File Management 3 This chapter contains command line interface (CLI) commands needed to manage the configuration files as well as other file management commands. boot system Tell the system where to access the Dell Networking OS image used to boot the system. Z9000 Syntax boot system {gateway ip address| stack-unit [{0-11 | 0-7]| all] [default | primary {system {A: | B:} | tftp: | | secondary]} To return to the default boot sequence, use the no boot system command.
PAGE 60
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810.
PAGE 61
CAUTION: This command deletes all files, including the startup configuration file. So, after executing this command, consider saving the running config as the startup config (use the write memory command or copy run start command). restore factory-defaults Restore factory defaults. Z9000 Syntax Parameters restore factory-defaults stack-unit {0-5 | all} {clear-all | nvram} factorydefaults Return the system to its factory default mode.
PAGE 62
When restoring all units in a stack, all the units in the stack are placed into standalone mode. When restoring a single unit in a stack, that unit placed in stand-alone mode. No other units in the stack are affected. When restoring units in stand-alone mode, the units remin in stand-alone mode after the restoration. After the restore is complete, the units power cycle immediately. CAUTION: There is no undo for this command.
PAGE 63
* persistent settings (stacking, fanout, etc.) * * All the units in the stack will be split into standalone units. * * After restoration the unit(s) will be powercycled immediately. * * Proceed with caution ! * ************************************************************** Proceed with factory settings? Confirm [yes/no]:yes -- Restore status -Unit Nvram Config -----------------------0 Success 1 Success 2 Success 3 Not present 4 Not present 5 Not present Power-cycling the unit(s).
PAGE 64
Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000 Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.
PAGE 65
Example Version 8.3.11.4 Output expanded to display current reload mode (normal or Jumpstart). Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.5.1.0 Introduced on the C-Series. E-Series Original command. Dell#show bootvar PRIMARY IMAGE FILE = system://B SECONDARY IMAGE FILE = tftp://10.16.127.35/Dell-SI-9-0-2-0.
PAGE 66
Example Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series Version 7.5.1.0 Introduced on the C-Series E-Series Original command Dell#show file flash://startup-config ! boot system rpm0 primary ftp://test:server@10.16.1.144//home/ images/ E1200_405-3.1.2b1.86.bin boot system rpm0 secondary flash://FTOS-ED-6.1.1.0.bin boot system rpm0 default ftp://:@/\ ! redundancy auto-synchroni
PAGE 67
• For a file on an FTP server, enter ftp:// user:password@hostip/filepath. • For a file on the external Flash, enter slot0:// followed by the filename. • For a file on a TFTP server, enter tftp://hostip/ filepath. • For a file on the USB port, enter usbflash://filepath. Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 68
FPGA IMAGE INFORMATION : -------------------------------------------------------------------Card FPGA Name Version Stack-unit 0 S6000 SYSTEM CPLD 10 Stack-unit 0 S6000 MASTER CPLD 12 Stack-unit 0 S6000 SLAVE CPLD 10 Dell# Usage Information NOTE: A filepath that contains a dot ( . ) is not supported. show running-config Display the current configuration and display changes from the default values.
PAGE 69
File Management ethernet for the current Ethernet CFM configuration fefd for the current FEFD configuration ftp for the current FTP configuration frrp for the current FRRP configuration fvrp for the current FVRP configuration gvrp for the current GVRP configuration host for the current host configuration hardwaremonitor for hardware-monitor action-on-error settings hypervisor for the current hypervisor configuration igmp for the current IGMP configuration interface for the current inte
PAGE 70
ospf for the current OSPF configuration pim for the current PIM configuration policy-mapinput for the current input policy map configuration policy-mapoutput for the current output policy map configuration po-failovergroup for the current port-channel failovergroup configuration prefix-list for the current prefix-list configuration privilege for the current privilege configuration qos-policyinput for the current input QoS policy configuration qos-policyoutput for the current output QoS
PAGE 71
uplinkstate-group for the uplink state group configuration users for the current users configuration vlt for the current VLT configuration wred-profile for the current wred-profile configuration configured (OPTIONAL) Enter the keyword configuration to display line card interfaces with non-default configurations only. status (OPTIONAL) Enter the keyword status to display the checksum for the running configuration and the start-up configuration.
PAGE 72
! Version 9-0(2-0) ! Last configuration change at Thu Apr 18 10:18:39 2013 by admin ! Startup-config last updated at Thu Apr 18 10:18:40 2013 by admin ! boot system stack-unit 0 primary system: A: boot system stack-unit 0 secondary tftp://10.16.127.35/DellSI-9-0-2-0.bin boot system stack-unit 0 default system: A: boot system gateway 10.16.132.
PAGE 73
Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on S-Series Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Expanded to include the last configuration change, start-up last updated (date and time), and who made the change.
PAGE 74
Command Fields Example (SSeries) Version 7.6.1.0 Introduced on the S-Series Version 7.5.1.0 Introduced on the C-Series. E-Series Original command. Lines Beginning With Description Dell Network... Name of the operating system Dell Operating... OS version number Dell Application... Software version Copyright (c)... Copyright information Build Time... Software build’s date stamp Build Path... Location of the software build files loaded on the system Dell Networking OS uptime is...
PAGE 75
Build Time: Mon Jul 16 22:19:01 PDT 2012 Build Path: /local/local/build/build15/8.3.12.0/SW/SRC/Radius Dell uptime is 1 minute(s) System image file is "s4810-14" System Type: S4810 Control Processor: Freescale QorIQ P2020 with 2147483648 bytes of memory. 128M bytes of boot flash memory. 1 52-port GE/TE/FG (SE) 52 Ten GigabitEthernet/IEEE 802.
PAGE 76
Parameters boot Enter the keyword boot to change the boot image. system Enter the keyword system to change the system image. ftp: After entering the keyword ftp:, you can either follow it with the location of the source file in this form: // userid:password@hostip/filepath or press Enter to launch a prompt sequence.
PAGE 77
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0(0.0) Added support for IPv6 for the file-url parameter. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Added support for the SSD on the Z9000 only.
PAGE 78
..................................... ............................................................... ..................................... ....................................! 12946259 bytes successfully copied Dell# reload upgrade fpga-image Use this command only on systems with SFM3 modules (and only when required by the Upgrade Procedure in the release notes).
PAGE 79
The following is a list of the Dell Networking OS version history for this command. Version 9.0.0.0 Introduced on the Z-Series. Version 8.3.1.0 Added the rpm option. Version 7.5.1.0 Introduced on the C-Series. Example Dell#upgrade sfm 1 autoreset SFM1: upgrade in progress !!! !!! !!! SFM1: upgrade complete SFM1 is active. Resetting it might temporarily impact traffic.
PAGE 80
PAGE 81
Control and Monitoring 4 This chapter contains the commands to configure and monitor the system, including Telnet, file transfer protocol (FTP), and trivial file transfer protocol (TFTP) as they apply to the following Dell Networking Z9000 platform. NOTE: Starting in version 8.3.11.4, the enable xfp-power-updates command was deprecated for the Z9000.
PAGE 82
Usage Information You must save the configuration and reload the system to implement ASF. When you enter the command, the system sends a message stating that the new mode is enabled when the system reloads. banner exec Configure a message that is displayed when your enter EXEC mode. Z9000 Syntax banner exec c line c To delete a banner, use the no banner exec command. Parameters c Enter the keywords banner exec, then enter a character delineator, represented here by the letter c. Press ENTER.
PAGE 83
Usage Information After entering the banner login command, type one or more spaces and a delineator character. Enter the banner text then the second delineator character. When the user is connected to the router, if a message of the day banner is configured, it displays first. If no message of the day banner is configured, the login banner and prompt appear. After the user has logged in, the EXEC banner (if configured) displays.
PAGE 84
Parameters keyboardinteractive Enter the keyword keyboard-interactive to require a carriage return (CR) to get the message banner prompt. c Enter a delineator character to specify the limits of the text banner. The delineator is a percent character (%). line Enter a text string for your text banner message ending the message with your delineator. The delineator is a percent character (%).
PAGE 85
Dell(conf)#end Dell#exit 13d21h9m: %RPM0-P:CP %SEC-5-LOGOUT: Exec session is terminated for user on line console This is the banner Dell con0 now available Press RETURN to get started. 13d21h10m: %RPM0-P:CP %SEC-5-LOGIN_SUCCESS: Login successful for user on line console This is the banner Dell> Related Commands banner motd — sets a Message of the Day banner. exec-banner — enables the display of a text string when you enter EXEC mode. banner motd Set a message of the day (MOTD) banner.
PAGE 86
Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series Original command Usage Information After entering the banner login command, type one or more spaces and a delineator character. Enter the banner text then the second delineator character.
PAGE 87
l2acl number ipv4acl number ipv6acl number ipv4qos number l2qos number l2pt number ipmacacl number [vmanqos | vmandual-qos] number ecfmacl number {openflow {4| 8}} Allocate space to each CAM region. Enter the CAM profile name then the amount of CAM space to be allotted. The total space allocated must equal 13. The ipv6acl range must be a factor of 2. Enter 4 or 8 for the number of OpenFlow FP blocks.
PAGE 88
When configuring space for IPv6 ACLs, the total number of Blocks must equal 13. Ranges for the CAM profiles are from 1 to 10, except for the ipv6acl profile which is from 0 to 10. The ipv6acl allocation must be a factor of 2 (2, 4, 6, 8, 10). If you enabled BMP 3.0, to perform a reload on the chassis to upgrade any configuration changes that have changed the NVRAM content, use the reload conditional nvram-cfg-change command. clear alarms Clear alarms on the system.
PAGE 89
clear command history Clear the command history log. Z9000 Syntax clear command history Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.
PAGE 90
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale.
PAGE 91
Example Version 8.3.11.1 Introduced on the Z9000. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series Original command. Dell#configure Dell(conf)# debug cpu-traffic-stats Enable the collection of computer processor unit (CPU) traffic statistics. Z9000 Syntax debug cpu-traffic-stats To disable the debugging, use the no debug cpu-traffic-stats command.
PAGE 92
The following message is an indication that collection of CPU traffic is automatically turned on. To view the traffic statistics, use the show cputraffic-stats command. If the CPU receives excessive traffic, traffic is rate controlled. NOTE: This command must be enabled before the show cpu-trafficstats command displays traffic statistics. Dell Networking recommends disabling debugging (no debug cpu-traffic-stats) after troubleshooting is complete.
PAGE 93
disable Return to EXEC mode. Z9000 Syntax Parameters disable [level] level (OPTIONAL) Enter a number for a privilege level of the Dell Networking OS. The range is from 0 to 15. The default is 1. Defaults 1 Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.
PAGE 94
Command Modes • CONFIGURATION • INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Example 94 Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000.
PAGE 95
enable Enter EXEC Privilege mode or any other privilege level configured. After entering this command, you may need to enter a password. Z9000 Syntax Parameters enable [level] level (OPTIONAL) Enter a number for a privilege level of Dell Networking OS. The range is from 0 to 15. Defaults 15 Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 96
enable optic-info-update interval Enable polling intervals of optical information updates for simple network management protocol (SNMP). Z9000 Syntax enable optical-info-update interval seconds To disable optical power information updates, use the no enable opticalinfo-update interval command. Parameters interval seconds Enter the keyword interval then the polling interval in seconds. The range is from 120 to 6000 seconds. The default is 300 seconds (5 minutes).
PAGE 97
Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 8.3.19.0 Deprecated command for S4820T. Replaced by the enable optic-info-update interval command to update information on temperature and power monitoring in the SNMP MIB.
PAGE 98
Command History • INTERFACE • TRACE-LIST • VRRP • ACCESS-LIST • PREFIX-LIST • AS-PATH ACL • COMMUNITY-LIST • ROUTER OSPF • ROUTER RIP • ROUTER ISIS • ROUTER BGP This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 99
Command Modes LINE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.7.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.1.1.0 Introduced on the E-Series ExaScale.
PAGE 100
Command Modes LINE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.
PAGE 101
• Command History COMMUNITY-LIST • PREFIX-LIST • ROUTER OSPF • ROUTER RIP • ROUTER ISIS • ROUTER BGP This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.
PAGE 102
Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series Original command. morpheus% ftp 10.31.1.111 Connected to 10.31.1.111. 220 Dell (1.0) FTP server ready Name (10.31.1.
PAGE 103
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.1.1.
PAGE 104
encryptiontype (OPTIONAL) After the keyword password, enter one of the following numbers: • 0 (zero) for an unecrypted (clear text) password • 7 (seven) for a hidden text password Defaults Not enabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.
PAGE 105
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.1.1.0 Introduced on the E-Series ExaScale.
PAGE 106
The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series Original command.
PAGE 107
• For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. • For a tunnel interface, enter the keyword tunnel. Defaults The IP address on the system that is closest to the Telnet address is used in the outgoing packets. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 108
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.1.1.0 Introduced on the E-Series ExaScale.
PAGE 109
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant FTOS Command Line Reference Guide. The following is a list of the FTOS version history for this command. Version 9.4. (0.0) Usage Information Introduced on the S-Series and Z-Series. Use this command to make the FTP clients VRF aware. The VRF name that you specify is used by the FTP client to reach the FTP server. If no VRF is specified, then the default vrf is used.
PAGE 110
ip telnet server vrf Configures the TELNET server on either a specific VRF or a management VRF. Z9000 Syntax ip telnet server vrf {management | vrf-name} To undo the TELNET server configuration, use the no ip telnet server [vrf vrf-name] command. Parameters vrf management Enter the keyword vrf followed by the keyword management to specify a management VRF that is used by the TELNET server.
PAGE 111
Parameters interface Enter the following keywords and slot/port or number information: • For Loopback interfaces, enter the keyword loopback then a number from zero (0) to 16383. • For a Port Channel, enter the keyword port-channel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
PAGE 112
ip telnet vrf Configures a TELNET client to use a specific VRF. Z9000 Syntax ip telnet [vrf vrf-name] To undo the TELENT client configuration, use the ip telnet [vrf vrf-name] command. Parameters vrf vrf-name Enter the keyword vrf and then the name of the VRF to specify the VRF that is used by the TELENT client. Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 113
• For Loopback interfaces, enter the keyword loopback then a number from zero (0) to 16383. • For a Port Channel, enter the keyword port-channel then a number. For the C-Series and S-Series, the range is 1 to 128. • For the SONET interfaces, enter the keyword sonet then slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
PAGE 114
To undo the TFTP client configuration, use the no ip tftp [vrf vrf-name] command. Parameters vrf vrf-name Enter the keyword vrf and then the name of the VRF to specify the VRF that is used by the TFTP client. Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant FTOS Command Line Reference Guide. The following is a list of the FTOS version history for this command. Version 9.4. (0.
PAGE 115
end-number (OPTIONAL) Enter a number from 1 to 9 as the last virtual terminal line to configure. You can configure multiple lines at one time. Defaults Not configured Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 116
Command Modes LINE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.1.1.
PAGE 117
NOTE: The :: notation specifies successive hexadecimal fields of zeros. count Enter the number of echo packets to be sent. The default is 5. • number: from 1 to 2147483647 • continuous: transmit echo request continuously datagram size Enter the ICMP datagram size. The range is from 36 to 15360 bytes. The default is 100. timeout Enter the interval to wait for an echo reply before timing out. The range is from 0 to 3600 seconds. The default is 2 seconds.
PAGE 118
sweep-minsize Enter the minimum size of datagram in sweep range. The range is from 52 to 15359 bytes. sweep-maxsize Enter the maximum size of datagram in sweep range. The range is from 53 to 15359 bytes. sweep-interval Enter the incremental value for sweep size. The range is from 1 to 15308 seconds. interface (IPv4 only) Enter the outgoing interface for multicast packets. Enter the IP address in A.B.C.D format. • For a Port Channel, enter the keyword port-channel then a number.
PAGE 119
Usage Information Version 8.1.1.0 Introduced on the E-Series ExaScale (IPv4). Version 7.9.1.0 Introduced VRF. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Added support for IPv6 address on the E-Series. When you enter the ping command without specifying an IP/IPv6 address (Extended Ping), you are prompted for a target IP/IPv6 address, a repeat count, a datagram size (up to 1500 bytes), a timeout (in seconds), and for Extended Commands.
PAGE 120
0/0/0 (ms) Dell# reload Reboot Dell Networking Operating System (OS). Z9000 Syntax Parameters reload [conditional nvram-cfg-change] conditional nvram-cfgchange Reload if the condition is true. A configuration change to the nvram requires a switch reload. To reload the switch, select nvram-cfg-change. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 121
send Send messages to one or all terminal line users. Z9000 Syntax Parameters send [*] | [line ] | [console] | [vty] * Enter the asterisk character * to send a message to all tty lines. line Send a message to a specific line. The range is from 0 to 11. console Enter the keyword console to send a message to the primary terminal line. vty Enter the keyword vty to send a message to the virtual terminal. Defaults none Command Modes EXEC Command History This guide is platform-specific.
PAGE 122
service timestamps To debug and log messages, add time stamps. This command adds either the uptime or the current time and date. Z9000 Syntax service timestamps [debug | log] [datetime [localtime] [msec] [show-timezone] | uptime] To disable timestamping, use the no service timestamps [debug | log] command. Parameters debug (OPTIONAL) Enter the keyword debug to add timestamps to debug messages. log (OPTIONAL) Enter the keyword log to add timestamps to log messages with severity from 0 to 6.
PAGE 123
Usage Information Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series Original command. If you do not specify parameters and enter service timestamps, it appears as service timestamps debug uptime in the running-configuration. To view the current options set for the service timestamps command, use the show running-config command. show alarms View alarms currently active in the system.
PAGE 124
E-Series Example Original command.
PAGE 125
show command-history Display a buffered log of all commands all users enter along with a time stamp. Z9000 Syntax show command-history Defaults none Command Modes Command History • • EXEC EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.
PAGE 126
[11/20 15:47:23]: CMD-(CLI):[protocol spanning-tree pvst]by default from console [11/20 15:47:23]: CMD-(CLI):[no disable]by default from console [11/20 15:47:23]: CMD-(CLI):[interface gigabitethernet 0/1]by default from console [11/20 15:47:23]: CMD-(CLI):[ip address 1.1.1.
PAGE 127
Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.
PAGE 128
show cpu-traffic-stats View the CPU traffic statistics. Z9000 Syntax Parameters show cpu-traffic-stats [port number | all | cp ] port number (OPTIONAL) Enter the port number to display traffic statistics on that port only. The range is from 1 to 1568. all (OPTIONAL) Enter the keyword all to display traffic statistics on all the interfaces receiving traffic, sorted based on the traffic. cp (OPTIONAL) Enter the keyword cp to display traffic statistics on the specified CPU.
PAGE 129
Example Dell#show cpu-traffic-stats Processor : CP -------------Received 100% traffic on GigabitEthernet 8/2 Total packets:100 LLC:0, SNAP:0, IP:100, ARP:0, other:0 Unicast:100, Multicast:0, Broadcast:0 Processor : RP1 --------------Received 62% traffic on GigabitEthernet 8/2 Total packets:500 LLC:0, SNAP:0, IP:500, ARP:0, other:0 Unicast:500, Multicast:0, Broadcast:0 Received 37% traffic on GigabitEthernet 8/1 Total packets:300 LLC:0, SNAP:0, IP:300, ARP:0, other:0 Unicast:300, Multicast:0, Broadcast:0 Pr
PAGE 130
Example Dell#show debug Generic IP: IP packet debugging is on for ManagementEthernet 0/0 Port-channel 1-2 Port-channel 5 GigabitEthernet 4/0-3,5-6,10-11,20 GigabitEthernet 5/0-1,5-6,10-11,15,17,19,21 ICMP packet debugging is on for GigabitEthernet 5/0,2,4,6,8,10,12,14,16 Dell# show inventory Display the S-Series or Z-Series switch type, components (including media), and Dell Networking Operating System (OS), including hardware identification numbers and configured protocols.
PAGE 131
Version 8.3.11.4 Output expanded to include Piece Part ID (PPID) and eSR4 optics. Version 8.3.11.1 Introduced on the Z9000. Version 7.6.1.0 Introduced this version of the command for S-Series. SSeries output differs from E-Series. Usage Information If there are no fiber ports in the unit, just the header under show inventory media displays. If there are fiber ports but no optics inserted, the output displays Media not present or accessible.
PAGE 132
APF12300017GEY 0 9 APF12300017GEY 0 10 APF12300017GEY Related Commands QSFP QSFP Yes 40GBASE-CR4-1M Yes 40GBASE-CR4-1M Yes • show interfaces — displays the interface configuration. • show interfaces transceiver — displays the physical status and operational status of an installed transceiver. The output also displays the transceiver’s serial number. show processes ipc flow-control Display the single window protocol queue (SWPQ) statistics.
PAGE 133
Usage Information Field Description Source QID /Tx Process Source Service Identifier Destination QID/Rx Process Destination Service Identifier Cur Len Current number of messages enqueued High Mark Highest number of packets in the queue at any time #of to / Timeout Timeout count #of Retr /Retries Number of retransmissions #msg Sent/Msg Sent/ Number of messages sent #msg Ackd/Ack Rcvd Number of messages acknowledged Retr /Available Retra Number of retries left Total/ Max Retra Number of
PAGE 134
Parameters clients Enter the keyword clients to display IFM client information. summary (OPTIONAL) Enter the keyword summary to display brief information about IFM clients. ifagt number Enter the keyword ifagt then the number of an interface agent to display software pipe and IPC statistics.
PAGE 135
Version 7.6.1.0 Example Introduced for the C-Series and S-Series.
PAGE 136
Version 9.4(0.0) Added support for the disabled-ports parameter . Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.4 The brief parameter no longer displays the current Reload mode. To display Reload mode, use the show reload-type command. Modified the show system stack-unit command output to support Piece Part ID (PPID). Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810.
PAGE 137
----------------------------------------------------------------------------------0 0 up up 7072 up 7072 0 1 up up 7021 up 7072 0 2 up up 7021 up 7021 Speed in RPM Example (S6000) Dell#show system Stack MAC : 90:b1:1c:f4:9b:79 Reload-Type : normal-reload] normal-reload [Next boot : -- Unit 0 -Unit Type : Management Unit Status : online Next Boot : online Required Type : S6000 - 32-port TE/FG (SI) Current Type : S6000 - 32-port TE/FG (SI) Master priority : 0 Hardware Rev : 4.
PAGE 138
-- Unit 5 -Unit Type Status Example (S4810) : Member Unit : not present Dell#show system stack-unit 0 -- Unit 0 -Unit Type : Management Unit Status : online Next Boot : online Required Type : S6000 - 32-port TE/FG (SI) Current Type : S6000 - 32-port TE/FG (SI) Master priority : 0 Hardware Rev : 4.0 Num Ports : 128 Up Time : 21 min, 8 sec Dell Networking OS Version : 9-4(0-168) Jumbo Capable : yes POE Capable : no FIPS Mode : disabled Boot Flash : 3.1.1.2 Boot Selector : 3.1.0.
PAGE 139
show tech-support Display a collection of data from other show commands, necessary for Dell Networking technical support to perform troubleshooting on S-Series or Z-Series switches. Z9000 Syntax Parameters show tech-support [stack-unit unit-id | page] stack-unit (OPTIONAL) Enter the keywords stack-unit to view CPU memory usage for the stack member designated by unit-id. The unit ID range for the Z9000 is from 0 to 7. page (OPTIONAL) Enter the keyword page to view 24 lines of text at a time.
PAGE 140
|except regular-expression | find regular-expression | save flash://result This display output is an accumulation of the same information that is displayed when you execute one of the following show commands: Example (SSeries) • show version • show clock • show running-config • show system stack-ports • show interfaces • show process memory • show process cpu • show file system • show system • show environment • show ip traffic • show ip management route • show ip route summary •
PAGE 141
Example (SSeries) Dell#show tech-support stack-unit 0 ----------------------------------- show version ------------------------------Dell Real Time Operating System Software Dell Operating System Version: 2.0 Dell Application Software Version: 9-4(0-168) Copyright (c) 1999-2014 by Dell Inc. All Rights Reserved. Build Time: Sun Mar 23 22:17:49 PDT 2014 Build Path: /work.
PAGE 142
ssh-peer-stack-unit Open an SSH connection to the peer stack-unit. Z9000 Syntax Parameters ssh-peer-stack-unit [-l username] -l username (OPTIONAL) Enter the keyword -l then your user name. The default is the user name associated with the terminal. Defaults Not configured. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 143
ipv6-address prefix-length Enter the IPv6 address in the x:x:x:x::x format then the prefix length in the /x format. The range is from /0 to /128. NOTE: The :: notation specifies successive hexadecimal fields of zeros. sourceinterface (OPTIONAL) Enter the keywords /source-interface then the interface information to include the source interface. Enter the following keywords and slot/port or number information: • For a Loopback interface, enter the keyword loopback then a number from zero (0) to 16383.
PAGE 144
Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series and added support for IPv6 address on the E-Series only. telnet-peer-stack-unit Open a Telnet connection to the peer stack unit. Z9000 Syntax telnet-peer-stack-unit Defaults Not configured. Command Modes Command History • • EXEC EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 145
Defaults 24 lines Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.
PAGE 146
• 30 hops max • 40 byte packet size • UDP port = 33434 Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T.
PAGE 147
TTL Hostname Probe1 Probe2 Probe3 1 10.11.199.190 001.000 ms 001.000 ms 002.000 ms 2 gwegress-sjc-02.Dell Networking.com (10.11.30.126) 005.000 ms 001.000 ms 001.000 ms 3 fw-sjc-01.Dell Networking.com (10.11.127.254) 000.000 ms 000.000 ms 000.000 ms 4 www.Dell Networking.com (10.11.84.18) 000.000 ms 000.000 ms 000.000 ms FTOS# Example (IPv6) Dell#traceroute 100::1 Type Ctrl-C to abort.
PAGE 148
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series Original command virtual-ip Configure a virtual IP address for the active management interface. You can configure virtual addresses both for IPv4 and IPv6 independently.
PAGE 149
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.5.1.0 Introduced on the C-Series. E-Series Original command. Usage Information You can configure both IPv4 and IPv6 virtual addresses simultaneously, but only one of each. Each time this command is issued, it replaces the previously configured address of the same family, IPv4 or IPv6.
PAGE 150
Usage Information 150 Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series Original command. The write memory command saves the running-configuration to the file labeled startup-configuration.
PAGE 151
802.1X 5 An authentication server must authenticate a client connected to an 802.1X switch port. Until the authentication, only extensible authentication protocol over LAN (EAPOL) traffic is allowed through the port to which a client is connected. After authentication is successful, normal traffic passes through the port. The Dell Networking operating software supports remote authentication dial-in service (RADIUS) and active directory environments using 802.1X Port Authentication.
PAGE 152
debug dot1x Display 802.1X debugging information. Z9000 Syntax Parameters debug dot1x [all | auth-pae-fsm | backend-fsm | eapol-pdu] [interface interface] all Enable all 802.1X debug messages. auth-pae-fsm Enable authentication PAE FSM debug messages. backend-fsm Enable backend FSM debug messages. eapol-pdu Enable the EAPOL frame trace and related debug messages. interface interface Restricts the debugging information to an interface.
PAGE 153
To delete the authentication failure VLAN, use the no dot1x auth-fail-vlan vlan-id [max-attempts number] command. Parameters vlan-id Enter the VLAN Identifier. The range is from 1 to 4094. max-attempts number (OPTIONAL) Enter the keywords max-attempts followed number of attempts desired before authentication fails. The range is from 1 to 5. The default is 3. Defaults 3 attempts Command Modes CONFIGURATION (conf-if-interface-slot/port) Command History This guide is platform-specific.
PAGE 154
dot1x auth-server Configure the authentication server to RADIUS. Z9000 Syntax dot1x auth-server radius Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.
PAGE 155
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.4.2.1 Introduced on the C-Series and S-Series. The prerequisites for enabling MAB-only authentication on a port are: • Enable 802.1X authentication globally on the switch and on the port (the dot1x authentication command).
PAGE 156
Related Commands Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 7.6.1.0 Introduced on the C-Series and S-Series. Version 7.4.1.0 Introduced on the E-Series TeraScale. dot1x authentication (Interface) — Enable dot1x on an interface. dot1x authentication (Interface) Enable dot1x on an interface.
PAGE 157
Related Commands dot1x authentication (Configuration) — Enable dot1x globally. dot1x guest-vlan Configure a guest VLAN for limited access users or for devices that are not 802.1X capable. Z9000 Syntax dot1x guest-vlan vlan-id To disable the guest VLAN, use the no dot1x guest-vlan vlan-id command. Parameters vlan-id Enter the VLAN Identifier. The range is from 1 to 4094. Defaults Not configured.
PAGE 158
If the host fails authentication for the designated number of times, the authenticator places the port in authentication failed VLAN (dot1x auth-failvlan). NOTE: You can create the Layer 3 portion of a guest VLAN and authentication fail VLANs regardless if the VLAN is assigned to an interface or not. After an interface is assigned a guest VLAN (which has an IP address), routing through the guest VLAN is the same as any other traffic. However, the interface may join/leave a VLAN dynamically.
PAGE 159
Usage Information Related Commands Version 8.3.11.1 Introduced on the Z9000. Version 8.4.1.0 Added the multi-auth option on the C-Series and S-Series. Version 8.3.2.0 Added the single-host and multi-host options on the C-Series, E-Series, and S-Series. • Single-host mode authenticates only one host per authenticator port and drops all other traffic on the port. • Multi-host mode authenticates the first host to respond to an Identity Request and then permits all other traffic on the port.
PAGE 160
Version 8.4.1.0 Usage Information Introduced on the C-Series and S-Series. To disable MAC authentication bypass on a port, enter the no dot1x mac-authbypass command. dot1x max-eap-req Configure the maximum number of times an extensive authentication protocol (EAP) request is transmitted before the session times out. Z9000 Syntax dot1x max-eap-req number To return to the default, use the no dot1x max-eap-req command.
PAGE 161
dot1x max-supplicants Restrict the number of supplicants that can be authenticated and permitted to access the network through the port. This configuration is only takes effect in Multi-auth mode. Z9000 Syntax Parameters dot1x max-supplicants number number Enter the number of supplicants that can be authenticated on a single port in Multi-auth mode. The range is from 1 to 128. The default is 128. Defaults 128 hosts can be authenticated on a single authenticator port.
PAGE 162
Parameters forceauthorized Enter the keywords force-authorized to forcibly authorize a port. auto Enter the keyword auto to authorize a port based on the 802.1X operation result. forceunauthorized Enter the keywords force-unauthorized to forcibly deauthorize a port. Defaults none Command Modes Auto Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 163
Defaults 60 seconds Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 7.6.1.
PAGE 164
Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 7.6.1.0 Introduced on the C-Series and S-Series. Version 7.4.1.0 Introduced on the E-Series. dot1x reauth-max Configure the maximum number of times a port can re-authenticate before the port becomes unauthorized.
PAGE 165
Version 7.4.1.0 Introduced on the E-Series. dot1x server-timeout Configure the amount of time after which exchanges with the server time-out. Z9000 Syntax dot1x server-timeout seconds To return to the default, use the no dot1x server-timeout command. Parameters seconds Enter a time-out value in seconds. The range is from 1 to 300, where 300 is implementation dependant. The default is 30. Defaults 30 seconds Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 166
Where the default values are as follows: dot1x server-timeout (30 seconds), radius-server retransmit (3 seconds), and radius-server timeout (5 seconds). For example: Dell(conf)#radius-server host 10.11.197.105 timeout 6 Dell(conf)#radius-server host 10.11.197.105 retransmit 4 Dell(conf)#interface gigabitethernet 2/23 Dell(conf-if-gi-2/23)#dot1x server-timeout 40 dot1x supplicant-timeout Configure the amount of time after which exchanges with the supplicant time-out.
PAGE 167
dot1x tx-period Configure the intervals at which EAPOL PDUs the Authenticator PAE transmits. Z9000 Syntax dot1x tx-period seconds To return to the default, use the no dot1x tx-period command. Parameters seconds Enter the interval time, in seconds, that EAPOL PDUs are transmitted. The range is from 1 to 65535. The default is 30. Defaults 30 seconds Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 168
mac-address • For a Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a Fast Ethernet interface, enter the keyword FastEthernet then the slot/port information. • For a Ten-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. (Optional) MAC address of an 802.1X-authenticated supplicant. Defaults none Command Modes • EXEC • EXEC privilege Command History This guide is platform-specific.
PAGE 169
Dell#show dot1x cos-mapping int g 2/21 mac-address 00:00:01:00:07:00 802.1p CoS re-map table on Gi 2/21: ---------------------------------802.1p CoS re-map table for Supplicant: 00:00:01:00:07:00 Dot1 Remapped Dot1p 0 7 1 6 2 5 3 4 4 3 5 2 6 1 7 0 show dot1x interface Display the 802.1X configuration of an interface.
PAGE 170
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.4.2.1 Added the mac-address option on the C-Series and SSeries. Version 7.6.1.0 Introduced on the C-Series, E-Series, and S-Series. Usage Information If you enable 802.1X multi-supplicant authentication on a port, additional 802.
PAGE 171
Quiet Period: ReAuth Max: Supplicant Timeout: Server Timeout: Re-Auth Interval: Max-EAP-Req: Host Mode: Max-Supplicants: 60 seconds 1 30 seconds 30 seconds 60 seconds 2 MULTI_AUTH 128 Port status and State info for Supplicant: 00:00:01:00:07:00 Port Auth Status: Untagged VLAN id: Auth PAE State: Backend State: Dell# Example (Interface) AUTHORIZED(MAC-AUTH-BYPASS) 4094 Authenticated Idle Dell#show dot1x interface g 0/21 802.
PAGE 172
PAGE 173
Access Control Lists (ACL) 6 Access control lists (ACLs) are supported by the Dell Networking operating software on the Z9000 platform.
PAGE 174
description Enter a description of up to 80 characters. Defaults Not configured. Command Modes • CONFIGURATION-STANDARD-ACCESS-LIST • CONFIGURATION-EXTENDED-ACCESS-LIST • CONFIGURATION-MAC ACCESS LIST-STANDARD • CONFIGURATION-MAC ACCESS LIST-EXTENDED Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 175
show config Display the current ACL configuration. Z9000 Syntax show config Command Modes • CONFIGURATION-STANDARD-ACCESS-LIST • CONFIGURATION-EXTENDED-ACCESS-LIST Command History • CONFIGURATION-MAC ACCESS LIST-STANDARD • CONFIGURATION-MAC ACCESS LIST-EXTENDED This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 176
NOTE: Also refer to the Commands Common to all ACL Types section. access-class Apply a standard ACL to a terminal line. Z9000 Syntax access-class access-list-name To remove an ACL, use the no access-class access-list-name command. Parameters access-listname Enter the name of a configured Standard ACL, up to 140 characters. Defaults Not configured. Command Modes LINE Command History This guide is platform-specific.
PAGE 177
Parameters access-listname (OPTIONAL) Enter the name of a configured access-list, up to 140 characters. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.
PAGE 178
implicit-permit (that is, if the traffic does not match the filters in the ACL, the traffic is permitted instead of dropped). vlan vlan-id (OPTIONAL) Enter the keyword vlan then the ID numbers of the VLANs. The range is from 1 to 4094 (you can use IDs from 1 to 4094). Defaults Not enabled. Command Modes INTERFACE/VRF MODE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 179
ip control-plane egress-filter Enable egress Layer 3 ACL lookup for IPv4 CPU traffic. Z9000 Syntax ip control-plane egress-filter Defaults Not enabled. Command Modes EXEC Privilege Command History Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. show ip accounting access-list Display the IP access-lists created on the switch and the sequence of filters.
PAGE 180
Command Modes Command History • • EXEC EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.5.1.
PAGE 181
The Z9000 supports both Ingress and Egress IP ACLs. NOTE: Also refer to the Commands Common to all ACL Types and Common IP ACL Commands sections. deny To drop packets with a certain IP address, configure a filter. Z9000 Syntax deny {source | any | host {ip-address}} To remove this filter, you have two choices: Parameters • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no deny {source [mask] | any | host ip-address} command.
PAGE 182
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Add the DSCP value for ACL matching. Version 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.
PAGE 183
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.10.0 Introduced on the S4810. Version 8.1.1.
PAGE 184
To remove this filter, you have two choices: Parameters • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no permit {source [mask] | any | host ip-address} command. source Enter the IP address in dotted decimal format of the network from which the packet was sent. mask (OPTIONAL) Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or non-contiguous.
PAGE 185
Version 8.3.1.0 Add the DSCP value for ACL matching. Version 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Added support for the non-contiguous mask and added the monitor option. Version 6.5.10 Expanded to include the optional QoS order priority for the ACL entry.
PAGE 186
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced on the E-Series ExaScale (IPv6).
PAGE 187
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.11.1 Introduced on the Z9000. Version 8.1.1.0 Introduced on the E-Series ExaScale Version 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.
PAGE 188
host ip-address Enter the keyword host then the IP address to specify a host IP address or hostname. count (OPTIONAL) Enter the keyword count to count packets the filter processes. bytes (OPTIONAL) Enter the keyword bytes to count bytes the filter processes. dscp (OPTIONAL) Enter the keyword dcsp to match to the IP DCSCP values. order (OPTIONAL) Enter the keyword order to specify the QoS order for the ACL entry.
PAGE 189
Usage Information Related Commands The order option is relevant in the context of the Policy QoS feature only. The following applies: • The seq sequence-number command is applicable only in an ACL group. • The order option works across ACL groups that have been applied on an interface via the QoS policy framework. • The order option takes precedence over seq sequence-number.
PAGE 190
Parameters ip Enter the keyword ip to configure a generic IP access list. The keyword ip specifies that the access list denies all IP protocols. ip-protocolnumber Enter a number from 0 to 255 to deny based on the protocol identified in the IP protocol header. source Enter the IP address of the network or host from which the packets were sent. mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or noncontiguous.
PAGE 191
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Add the DSCP value for ACL matching. Version 8.
PAGE 192
deny icmp To drop all or specific internet control message protocol (ICMP) messages, configure a filter. Z9000 Syntax deny icmp {source mask | any | host ip-address} {destination mask | any | host ip-address} [dscp] [count [byte] | log] [order] [monitor] [fragments] To remove this filter, you have two choices: • • Parameters 192 Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 193
based Monitoring” in the Port Monitoring chapter of the Dell Networking OS Configuration Guide. fragments Enter the keyword fragments to use ACLs to control packet fragments. Defaults Not configured. Command Modes CONFIGURATION-EXTENDED-ACCESS-LIST Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 194
deny tcp Configure a filter that drops transmission control protocol (TCP) packets meeting the filter criteria. Z9000 Syntax deny tcp {source mask | any | host ip-address} [bit] [operator port [port]] {destination mask | any | host ip-address} [dscp] [bit] [operator port [port]] [count [byte] | log] [order] [monitor] [fragments] To remove this filter, you have two choices: Parameters • Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 195
port port Enter the application layer port number. Enter two port numbers if using the range logical operand. The range is from 0 to 65535. The following list includes some common TCP port numbers: • • • • 23 = Telnet 20 and 21 = FTP 25 = SMTP 169 = SNMP destination Enter the IP address of the network or host to which the packets are sent. mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or non-contiguous.
PAGE 196
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Added the keyword dscp. Version 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.
PAGE 197
5 6 7 8 0001110000000000 0001111000000000 0001111100000000 0001111101000000 1111111000000000 1111111100000000 1111111111000000 1111111111111111 7168 7680 7936 8000 7679 7935 7999 8000 512 256 64 1 Total Ports: 4001 Example An ACL rule with a TCP port lt 1023 uses only one entry in the CAM. Rule# Data Mask From To 1 0000000000000000 1111110000000000 0 #Covered 1023 1024 Total Ports: 1024 Related Commands deny — assigns a filter to deny IP traffic.
PAGE 198
• eq = equal to • neq = not equal to • gt = greater than • lt = less than • range = inclusive range of ports (you must specify two ports for the port command) port port Enter the application layer port number. Enter two port numbers if using the range logical operand. The range is from 0 to 65535. destination Enter the IP address of the network or host to which the packets are sent. mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.
PAGE 199
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Added the keyword dscp. Version 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.
PAGE 200
5 6 7 8 0001110000000000 0001111000000000 0001111100000000 0001111101000000 1111111000000000 1111111100000000 1111111111000000 1111111111111111 7168 7680 7936 8000 7679 7935 7999 8000 512 256 64 1 Total Ports: 4001 Example An ACL rule with a TCP port lt 1023 uses only one entry in the CAM. Rule# Data Mask From To 1 0000000000000000 1111110000000000 0 #Covered 1023 1024 Total Ports: 1024 Related Commands deny — assigns a filter to deny IP traffic.
PAGE 201
Usage Information Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names were up to 16 characters long. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. The number of entries allowed per ACL is hardware-dependent. For detailed specification on entries allowed per ACL, refer to your line card documentation.
PAGE 202
destination Enter the IP address of the network or host to which the packets are sent. count (OPTIONAL) Enter the keyword count to count packets processed by the filter. bytes (OPTIONAL) Enter the keyword bytes to count bytes processed by the filter. dscp (OPTIONAL) Enter the keyword dcsp to match to the IP DCSCP values. order (OPTIONAL) Enter the keyword order to specify the QoS priority for the ACL entry.
PAGE 203
Usage Information The order option is relevant in the context of the Policy QoS feature only. For more information, refer to the “Quality of Service” chapter of the Dell Networking OS Configuration Guide. The software cannot count both packets and bytes; when you enter the count byte options, only bytes are incremented. Related Commands ip access-list extended — creates an extended ACL. permit tcp — assigns a permit filter for TCP packets. permit udp — assigns a permit filter for UDP packets.
PAGE 204
• urg: urgent field dscp Enter the keyword dscp to deny a packet based on the DSCP value. The range is from 0 to 63. operator (OPTIONAL) Enter one of the following logical operand: port port • eq = equal to • neq = not equal to • gt = greater than • lt = less than • range = inclusive range of ports (you must specify two ports for the port parameter) Enter the application layer port number. Enter two port numbers if you are using the range logical operand. The range is from 0 to 65535.
PAGE 205
NOTE: For more information, refer to the Flow-based Monitoring section in the Port Monitoring chapter of the Dell Networking OS Configuration Guide. fragments Enter the keyword fragments to use ACLs to control packet fragments. Defaults Not configured. Command Modes CONFIGURATION-EXTENDED-ACCESS-LIST Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 206
The S-Series cannot count both packets and bytes; when you enter the count byte options, only bytes are incremented. The monitor option is relevant in the context of flow-based monitoring only. For more information, refer to Port Monitoring. Most ACL rules require one entry in the CAM. However, rules with TCP and UDP port operators (for example, gt, lt, or range) may require more than one entry.
PAGE 207
Parameters • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no permit udp {source mask | any | host ip-address} {destination mask | any | host ip-address command. source Enter the IP address of the network or host from which the packets were sent. mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or non-contiguous.
PAGE 208
in which you are creating the rule is applied to the monitored interface. NOTE: For more information, refer to the Flow-based Monitoring section in the Port Monitoring chapter of the Dell Networking OS Configuration Guide. fragments Enter the keyword fragments to use ACLs to control packet fragments. Defaults Not configured. Command Modes CONFIGURATION-EXTENDED-ACCESS-LIST Command History This guide is platform-specific.
PAGE 209
The S-Series cannot count both packets and bytes; when you enter the count byte options, only bytes are incremented. The monitor option is relevant in the context of flow-based monitoring only. For more information, refer to Port Monitoring. Most ACL rules require one entry in the CAM. However, rules with TCP and UDP port operators (for example, gt, lt, or range) may require more than one entry.
PAGE 210
access-listname Enter the name of a configured IP access list, up to 140 characters. StartingSeqNu m Enter the starting sequence number to resequence. The range is from 0 to 4294967290. Step-toIncrement Enter the step to increment the sequence number. The range is from 1 to 4294967290. Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific.
PAGE 211
Step-toIncrement Enter the step to increment the sequence number. The range is from 1 to 65535. Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.11.1 Introduced on the Z9000. Version 8.1.1.
PAGE 212
permit Enter the keyword permit to configure a filter to forward packets meeting this criteria. ip-protocolnumber Enter a number from 0 to 255 to filter based on the protocol identified in the IP protocol header. icmp Enter the keyword icmp to configure an ICMP access list filter. ip Enter the keyword ip to configure a generic IP access list. The keyword ip specifies that the access list permits all IP protocols. tcp Enter the keyword tcp to configure a TCP access list filter.
PAGE 213
byte (OPTIONAL) Enter the keyword byte to count bytes the filter processes. log (OPTIONAL, E-Series only) Enter the keyword log to enter ACL matches in the log. Supported on Jumbo-enabled line cards only. dscp (OPTIONAL) Enter the keyword dcsp to match to the IP DCSCP values. order (OPTIONAL) Enter the keyword order to specify the QoS order for the ACL entry. The range is from 0 to 254 (where 0 is the highest priority and 254 is the lowest; lower-order numbers have a higher priority).
PAGE 214
Usage Information Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Added support for the non-contiguous mask and added the monitor option. Deprecated the keyword established. Version 6.5.10 Expanded to include the optional QoS order priority for the ACL entry. The monitor option is relevant in the context of flow-based monitoring only. For more information, refer to Port Monitoring. The order option is relevant in the context of the Policy QoS feature only.
PAGE 215
The MAC ACL can be applied on Physical, Port-channel and VLAN interfaces. As per the specified rules in the acl, the traffic on the interface/ VLAN members or Port-channel members will be permitted or denied. clear counters mac access-group Clear counters for all or a specific MAC ACL. Z9000 Syntax Parameters clear counters mac access-group [mac-list-name] mac-list-name (OPTIONAL) Enter the name of a configured MAC access list.
PAGE 216
Parameters access-listname Enter the name of a configured MAC access list, up to 140 characters. vlan vlan-range (OPTIONAL) Enter the keyword vlan and then enter a range of VLANs. The range is from 1 to 4094 (you can use IDs 1 to 4094). NOTE: This option is available only with the keywordin option. in Enter the keyword in to configure the ACL to filter incoming traffic. out Enter the keyword out to configure the ACL to filter outgoing traffic. NOTE: The option is not available on the S-Series.
PAGE 217
Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. Usage Information You can assign one ACL (standard or extended) to an interface. Related Commands mac access-list standard — configures a standard MAC ACL. mac access-list extended — configures an extended MAC ACL.
PAGE 218
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.4.1.0 Introduced. show mac accounting access-list Display MAC access list configurations and counters (if configured).
PAGE 219
Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series pre-Version 6.1.1.0 Introduced on the E-Series.
PAGE 220
deny To drop packets with a the MAC address specified, configure a filter. Z9000 Syntax deny {any | mac-source-address [mac-source-address-mask]} [count [byte]] [log] [monitor] To remove this filter, you have two choices: Parameters • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no deny {any | mac-source-address mac-source-addressmask} command. any Enter the keyword any to specify that all routes are subject to the filter.
PAGE 221
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Added the monitor option. When you use the log option, the CP processor logs detail the packets that match.
PAGE 222
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.
PAGE 223
Parameters any Enter the keyword any to forward all packets received with a MAC address. mac-sourceaddress Enter a MAC address in nn:nn:nn:nn:nn:nn format. mac-sourceaddress-mask (OPTIONAL) Specify which bits in the MAC address must match. If no mask is specified, a mask of 00:00:00:00:00:00 is applied (in other words, the filter allows only MAC addresses that match). count (OPTIONAL) Enter the keyword count to count packets processed by the filter.
PAGE 224
Usage Information When you use the log option, the CP processor logs details about the packets that match. Depending on how many packets match the log entry and at what rate, the CP may become busy as it has to log these packets’ details. NOTE: When ACL logging and byte counters are configured simultaneously, byte counters may display an incorrect value. Configure packet counters with logging instead. Related Commands deny — configures a MAC ACL filter to drop packets.
PAGE 225
in which you are creating the rule is applied to the monitored interface. NOTE: For more information, refer to the “Flow-based Monitoring” section in the Port Monitoring chapter of the Dell Networking OS Configuration Guide. Defaults Not configured Command Modes CONFIGURATION-MAC ACCESS LIST-STANDARD Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 226
Extended MAC ACL Commands When an access-list is created without any rule and then applied to an interface, ACL behavior reflects implicit permit. The following commands configure Extended MAC ACLs. The Z9000 supports both Ingress and Egress MAC ACLs. NOTE: For more information, also refer to the Commands Common to all ACL Types and Common MAC Access List Commands sections. deny To drop packets that match the filter criteria, configure a filter.
PAGE 227
ethertype operator (OPTIONAL) To filter based on protocol type, enter one of the following Ethertypes: • ev2 - is the Ethernet II frame format • llc - is the IEEE 802.3 frame format • snap - is the IEEE 802.3 SNAP frame format count (OPTIONAL) Enter the keyword count to count packets processed by the filter. byte (OPTIONAL) Enter the keyword byte to count bytes processed by the filter. log (OPTIONAL, E-Series only) Enter the keyword log to log the packets.
PAGE 228
NOTE: When ACL logging and byte counters are configured simultaneously, byte counters may display an incorrect value. Configure packet counters with logging instead. Related Commands permit — configures a MAC address filter to pass packets. seq — configures a MAC address filter with a specified sequence number. mac access-list extended Name a new or existing extended MAC access control list (extended MAC ACL).
PAGE 229
pre-Version 6.1.1.0 Usage Information Introduced on the E-Series. The number of entries allowed per ACL is hardware-dependent. For detailed specifications on entries allowed per ACL, refer to your line card documentation. Prior to 7.8.1.0, names are up to 16 characters long.
PAGE 230
• Parameters Use the no permit {any | host mac-address | mac-source-address mac-source-address-mask} {any | mac-destination-address macdestination-address-mask} command. any Enter the keyword any to forward all packets. host Enter the keyword host then a MAC address to forward packets with that host address. mac-sourceaddress Enter a MAC address in nn:nn:nn:nn:nn:nn format. mac-sourceaddress-mask (OPTIONAL) Specify which bits in the MAC address must match.
PAGE 231
Defaults Not configured. Command Modes CONFIGURATION-MAC ACCESS LIST-EXTENDED Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.
PAGE 232
Parameters sequencenumber Enter a number as the filter sequence number. The range is from zero (0) to 65535. deny Enter the keyword deny to drop any traffic matching this filter. permit Enter the keyword permit to forward any traffic matching this filter. any Enter the keyword any to filter all packets. host macaddress Enter the keyword host and then enter a MAC address to filter packets with that host address. mac-sourceaddress Enter a MAC address in nn:nn:nn:nn:nn:nn format.
PAGE 233
NOTE: For more information, refer to the Flow-based Monitoring section in the Port Monitoring chapter of the Dell Networking OS Configuration Guide. Defaults Not configured. Command Modes CONFIGURATION-MAC ACCESS LIST-STANDARD Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 234
clear ip prefix-list Reset the number of times traffic mets the conditions (“hit” counters) of the configured prefix lists. Z9000 Syntax Parameters clear ip prefix-list [prefix-name] prefix-name (OPTIONAL) Enter the name of the configured prefix list to clear only counters for that prefix list, up to 140 characters long. Defaults Clears “hit” counters for all prefix lists unless a prefix list is specified. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 235
Parameters ip-prefix Specify an IP prefix in the network/length format. For example, 35.0.0.0/ 8 means match the first 8 bits of address 35.0.0.0. ge min-prefixlength (OPTIONAL) Enter the keyword ge and then enter the minimum prefix length, which is a number from zero (0) to 32. le max-prefixlength (OPTIONAL) Enter the keyword le and then enter the maximum prefix length, which is a number from zero (0) to 32. Defaults Not configured.
PAGE 236
Parameters prefix-name Enter a string up to 16 characters long as the name of the prefix list, up to 140 characters long. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.
PAGE 237
ge min-prefixlength (OPTIONAL) Enter the keyword ge and then enter the minimum prefix length, which is a number from zero (0) to 32. le max-prefixlength (OPTIONAL) Enter the keyword le and then enter the maximum prefix length, which is a number from zero (0) to 32. Command Modes PREFIX-LIST Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 238
Parameters sequencenumber Enter a number. The range is from 1 to 4294967294. deny Enter the keyword deny to configure a filter to drop packets meeting this condition.. permit Enter the keyword permit to configure a filter to forward packets meeting this condition. any (OPTIONAL) Enter the keyword any to match any packets. ip-prefix /nn (OPTIONAL) Specify an IP prefix in the network/length format. For example, 35.0.0.0/8 means match the first 8 bits of address 35.0.0.0.
PAGE 239
show config Display the current PREFIX-LIST configurations. Z9000 Syntax show config Command Modes PREFIX-LIST Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000.
PAGE 240
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.8.1.
PAGE 241
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.8.1.
PAGE 242
continue To a route-map entry with a higher sequence number, configure a route-map. Z9000 Syntax Parameters continue [sequence-number] sequencenumber (OPTIONAL) Enter the route map sequence number. The range is from 1 to 65535. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 243
• A successful match with a continue clause, the route map executes the set clauses and then goes to the specified route map entry upon execution of the continue clause. • If the next route map entry contains a continue clause, the route map executes the continue clause if a successful match occurs. • If the next route map entry does not contain a continue clause, the route map evaluates normally.
PAGE 244
Related Commands Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. pre-Version 7.7.1.0 Introduced. route-map — enables a route map. match as-path To match routes that have a certain AS number in their BGP path, configure a filter. Z9000 Syntax match as-path as-path-name To delete a match AS path filter, use the no match as-path as-path-name command.
PAGE 245
Related Commands set as-path — adds information to the BGP AS_PATH attribute. match community To match routes that have a certain COMMUNITY attribute in their BGP path, configure a filter. Z9000 Syntax match community community-list-name [exact] To delete a community match filter, use the no match community command. Parameters communitylist-name Enter the name of a configured community list. exact (OPTIONAL) Enter the keywords exact to process only those routes with this community list name.
PAGE 246
match interface To match routes whose next hop is on the interface specified, configure a filter. Z9000 Syntax match interface interface To remove a match, use the no match interface interface command. Parameters interface Enter the following keywords and slot/port or number information: • . • For the loopback interface, enter the keyword loopback then a number from zero (0) to 16383. • For a Port Channel interface, enter the keyword portchannel then a number. The range is from 1 to 128.
PAGE 247
pre-Version 6.1.1.0 Related Commands Introduced on the E-Series. match ip address — redistributes routes that match an IP address. match ip next-hop — redistributes routes that match the next-hop IP address. match ip route-source — redistributes routes that match routes advertised by other routers. match metric — redistributes routes that match a specific metric. match route-type — redistributes routes that match a route type. match tag — redistributes routes that match a specific tag.
PAGE 248
Related Commands Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. match interface — redistributes routes that match the next-hop interface. match ip next-hop — redistributes routes that match the next-hop IP address. match ip route-source — redistributes routes that match routes advertised by other routers. match metric — redistributes routes that match a specific metric.
PAGE 249
Related Commands Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. match interface — redistributes routes that match the next-hop interface.
PAGE 250
Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810 Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names were up to 16 characters long. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.
PAGE 251
Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. match interface — redistributes routes that match the next-hop interface.
PAGE 252
Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale.
PAGE 253
The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series.
PAGE 254
Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. match interface — redistributes routes that match the next-hop interface.
PAGE 255
prompted for a sequence number if there are multiple instances of the route map. The range is from 1 to 65535. Defaults Not configured. If you do not define a keyword (permit or deny) for the route map, the permit action is the default. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 256
To remove an AS-Path setting, use the no set as-path {prepend as-number | tag} command. Parameters prepend asnumber Enter the keyword prepend and then enter up to eight AS numbers to be inserted into the BGP path information. The range is from 1 to 65535. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 257
set automatic-tag To automatically compute the tag value of the route, configure a filter. Z9000 Syntax set automatic-tag To return to the default, enter no set automatic-tag. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 258
To insert the community list into the COMMUNITY attribute, use the no set comm-list community-list-name delete command. Parameters communitylist-name Enter the name of an established Community list, up to 140 characters. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 259
set community Allows you to assign a BGP COMMUNITY attribute. Z9000 Syntax set community {community-number | local-as | no-advertise | noexport | none} [additive] To delete a BGP COMMUNITY attribute assignment, use the no set community {community-number | local-as | no-advertise | no-export | none} command. Parameters communitynumber Enter the community number in AA:NN format where AA is the AS number (2 bytes) and NN is a value specific to that autonomous system.
PAGE 260
Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. ip community-list — configures community access list.
PAGE 261
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Dell Networking OS Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale.
PAGE 262
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. Usage Information The set local-preference command changes the LOCAL_PREF attribute for routes meeting the route map criteria.
PAGE 263
Related Commands Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. set automatic-tag — computes the tag value of the route. set level — specifies the OSPF area for route redistribution.
PAGE 264
Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Implemented the keyword internal. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. set automatic-tag — computes the tag value of the route.
PAGE 265
Usage Information Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. If you configure the set next-hop command, its configuration takes precedence over the neighbor next-hop-self command in the ROUTER BGP mode.
PAGE 266
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. set tag To specify a tag for redistributed routes, configure a filter. Z9000 Syntax set tag tag-value To delete a setting, use the no set tag command.
PAGE 267
Related Commands set automatic-tag — computes the tag value of the route. set level — specifies the OSPF area for route redistribution. set metric — specifies the metric value assigned to redistributed routes. set metric-type — specifies the route type assigned to redistributed routes. set weight To add a non-RFC compliant attribute to the BGP route to assist with route selection, configure a filter. Z9000 Syntax set weight weight To delete a weight specification, use the no set weight weight command.
PAGE 268
Usage Information If you do not use the set weight command, router-originated paths have a weight attribute of 32768 and all other paths have a weight attribute of zero. show config Display the current route map configuration. Z-Series Syntax show config Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 269
Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.
PAGE 270
Parameters as-path-name Enter the access-list name, up to 140 characters. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.
PAGE 271
Example Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. pre-Version 6.1.1.0 Introduced on the E-Series. Dell#show ip as-path-access-lists ip as-path access-list 1 permit ^$ permit ^$.*$$ deny .* ip as-path access-list 91 permit ^$ deny .* permit ^$.*$$ Dell# IP Community List Commands IP community list commands are supported on the platform.
PAGE 272
Example Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. pre-Version 6.1.1.0 Introduced on the E-Series. Dell(conf)#ip community-list TestComList Dell(config-community-list)# show ip community-lists Display configured IP community lists in alphabetic order.
PAGE 273
deny deny deny deny deny deny deny deny deny deny deny deny deny Dell# 14551:20 701:112 702:112 703:112 704:112 705:112 14551:112 701:666 702:666 703:666 704:666 705:666 14551:666 deny (for Standard IP ACLs) To drop packets with a certain IP address, configure a filter.
PAGE 274
Command Modes Command History Usage Information CONFIGURATION-STANDARD-ACCESS-LIST Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. Version 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 275
Parameters Defaults • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no deny {ip | ip-protocol-number} {source mask | any | host ip-address} {destination mask | any | host ip-address} command. log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 276
capability, traffic with particular flows that are traversing through the ingress and egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface. This feature is particularly useful when looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic.
PAGE 277
Command Modes Command History Usage Information CONFIGURATION-STANDARD-ACCESS-LIST Version 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 278
• Parameters Defaults Use the no deny tcp {source mask | any | host ip-address} {destination mask | any | host ip-address} command. log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages. threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated. with the seq, permit, or deny commands.
PAGE 279
monitoring only specified traffic instead all traffic on the interface. This feature is particularly useful when looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic. You may specify traffic using standard or extended access-lists. This mechanism copies all incoming or outgoing packets on one port and forwards (mirrors) them to another port. The source port is the monitored port (MD) and the destination port is the monitoring port (MG).
PAGE 280
Usage Information When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero. If ACL logging was stopped previously because the configured threshold is exceeded, it is re-enabled for this new interval.
PAGE 281
in which you are creating the rule is applied to the monitored interface. Defaults By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes Command History Usage Information CONFIGURATION-EXTENDED-ACCESS-LIST Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. Version 9.4(0.
PAGE 282
Syntax deny icmp {source mask | any | host ip-address} {destination mask | any | host ip-address} [dscp] [message-type] [count [byte]] [order] [fragments] [log [interval minutes] [thresholdin-msgs [count]] [monitor] To remove this filter, you have two choices: Parameters Defaults • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no deny icmp {source mask | any | host ip-address} {destination mask | any | host ip-address} command.
PAGE 283
ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces. You can activate flow-based monitoring for a monitoring session by entering the flow-based enable command in the Monitor Session mode. When you enable this capability, traffic with particular flows that are traversing through the ingress and egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction.
PAGE 284
Defaults By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes Command History Usage Information CONFIGURATION-EXTENDED-ACCESS-LIST Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. Version 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms.
PAGE 285
• • Parameters Defaults Use the no seq sequence-number command if you know the filter’s sequence number. Use the no deny {any | mac-source-address mac-source-addressmask} command. log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages. threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated.
PAGE 286
egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface. This feature is particularly useful when looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic. You may specify traffic using standard or extended access-lists.
PAGE 287
Defaults By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes Command History Usage Information CONFIGURATION-MAC ACCESS LIST-EXTENDED Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. Version 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms.
PAGE 288
permit (for Standard IP ACLs) To permit packets from a specific source IP address to leave the switch, configure a filter. Syntax permit {source [mask]| any | host ip-address} [count [byte]] [dscp value] [order] [fragments] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, you have two choices: • • Parameters Defaults Use the no seq sequence-number command if you know the filter’s sequence number. Use the no permit {source [mask] | any | host ip-address} command.
PAGE 289
standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces. You can activate flow-based monitoring for a monitoring session by entering theflow-based enable command in the Monitor Session mode.
PAGE 290
monitor Defaults (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes Command History Usage Information CONFIGURATION-EXTENDED-ACCESS-LIST Version 9.
PAGE 291
address-mask | any} [count [byte]] [order] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, you have two choices: Parameters Defaults • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no permit ether-type protocol-type-number {destination-mac-address mac-address-mask | any} vlan vlanid {source-mac-address mac-address-mask | any} command. log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 292
You can activate flow-based monitoring for a monitoring session by entering the flow-based enable command in the Monitor Session mode. When you enable this capability, traffic with particular flows that are traversing through the ingress and egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface.
PAGE 293
Command Modes Command History Usage Information CONFIGURATION-STANDARD-ACCESS-LIST Version 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 294
• Parameters Defaults Use the no permit udp {source mask | any | host ip-address} {destination mask | any | host ip-address command. log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages. threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated with the seq, permit, or deny commands.
PAGE 295
Layer 3 ingress and egress traffic. You may specify traffic using standard or extended access-lists. This mechanism copies all incoming or outgoing packets on one port and forwards (mirrors) them to another port. The source port is the monitored port (MD) and the destination port is the monitoring port (MG). Related Commands ip access-list extended — creates an extended ACL. permit — assigns a permit filter for IP packets. permit tcp — assigns a permit filter for TCP packets.
PAGE 296
Command Modes Command History Usage Information CONFIGURATION-EXTENDED-ACCESS-LIST Version 9.4(0.0) Added the support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. Version 9.3(0.0) Added the support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 297
To remove this filter, you have two choices: • • Parameters Defaults Use the no seq sequence-number command if you know the filter’s sequence number. Use the no permit {any | mac-source-address mac-sourceaddress-mask} command. log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 298
particularly useful when looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic. You may specify traffic using standard or extended access-lists. This mechanism copies all incoming or outgoing packets on one port and forwards (mirrors) them to another port. The source port is the monitored port (MD) and the destination port is the monitoring port (MG). Related Commands deny — configures a MAC ACL filter to drop packets.
PAGE 299
Usage Information When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero. If ACL logging was stopped previously because the configured threshold is exceeded, it is re-enabled for this new interval.
PAGE 300
Defaults threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated with the seq, permit, or deny commands. The threshold range is from 1 to 100. interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The interval range is from 1 to 10 minutes.
PAGE 301
Related Commands ip access-list extended — creates an extended ACL. permit — assigns a permit filter for IP packets. permit udp — assigns a permit filter for UDP packets. seq arp (for Extended MAC ACLs) Configure an egress filter with a sequence number that filters ARP packets meeting this criteria. This command is supported only on 12-port GE line cards with SFP optics. For specifications, refer to your line card documentation. NOTE: Only the options that have been newly introduced in Release 9.3(0.
PAGE 302
Command History Usage Information Version 9.3.0.0 Added support for logging of ACLs on the S4810, S4820T, Z9000, and MXL 10/40GbE Switch IO Module platforms. Version 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, Z9000, and MXL 10/40GbE Switch IO Module platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 303
Parameters Defaults log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages. threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated. with the seq, permit, or deny commands. You can enter a threshold in the range of 1-100.
PAGE 304
Layer 3 ingress and egress traffic. You may specify traffic using standard or extended access-lists. This mechanism copies all incoming or outgoing packets on one port and forwards (mirrors) them to another port. The source port is the monitored port (MD) and the destination port is the monitoring port (MG). seq (for IP ACLs) Assign a sequence number to a deny or permit filter in an extended IP access list while creating the filter.
PAGE 305
new interval commences from zero. If ACL logging was stopped previously because the configured threshold is exceeded, it is re-enabled for this new interval. If ACL logging is stopped because the configured threshold is exceeded, it is reenabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs.
PAGE 306
monitor Defaults (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes Command History Usage Information ACCESS-LIST Version 9.4(0.
PAGE 307
permit udp (for IPv6 ACLs) Configure a filter to pass UDP packets meeting the filter criteria. Syntax permit udp {source address mask | any | host ipv6-address} [operator port [port]] {destination address | any | host ipv6address} [operator port [port]] [count [byte]] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, you have two choices: • • Parameters Defaults Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 308
If ACL logging is stopped because the configured threshold is exceeded, it is reenabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces.
PAGE 309
monitor Defaults (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is 5 minutes. By default, flow-based monitoring is not enabled. Command Modes Command History Usage Information ACCESS-LIST Version 9.4(0.
PAGE 310
permit icmp (for IPv6 ACLs) To allow all or specific internet control message protocol (ICMP) messages, configure a filter. Syntax permit icmp {source address mask | any | host ipv6-address} {destination address | any | host ipv6-address} [message-type] [count [byte]] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, you have two choices: Parameters Defaults • Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 311
If ACL logging is stopped because the configured threshold is exceeded, it is reenabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces.
PAGE 312
Defaults By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes Command History Usage Information ACCESS-LIST Version 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms.
PAGE 313
• Parameters Defaults Use the no deny udp {source address mask | any | host ipv6address} {destination address | any | host ipv6-address} command log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages. threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated. with the seq, permit, or deny commands.
PAGE 314
egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface. This feature is particularly useful when looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic. You may specify traffic using standard or extended access-lists.
PAGE 315
Command Modes Command History Usage Information ACCESS-LIST Version 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 316
• • Parameters Defaults Use the no seq sequence-number command syntax if you know the filter’s sequence number Use the no deny icmp {source address mask | any | host ipv6address} {destination address | any | host ipv6-address} command log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 317
ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface. This feature is particularly useful when looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic. You may specify traffic using standard or extended access-lists. This mechanism copies all incoming or outgoing packets on one port and forwards (mirrors) them to another port.
PAGE 318
Version 9.4(0.0) Usage Information Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero.
PAGE 319
7 Access Control List (ACL) VLAN Groups and Content Addressable Memory (CAM) This chapter describes the access control list (ACL) VLAN group and content addressable memory (CAM) enhancements. member vlan Add VLAN members to an ACL VLAN group. Syntax Parameters member vlan {VLAN-range} VLAN-range Enter the member VLANs using comma-separated VLAN IDs, a range of VLAN IDs, a single VLAN ID, or a combination.
PAGE 320
ip access-group Apply an egress IP ACL to the ACL VLAN group. Syntax Parameters ip access-group {group name} out implicit-permit group-name Enter the name of the ACL VLAN group where you want the egress IP ACLs applied, up to 140 characters. out Enter the keyword out to apply the ACL to outgoing traffic.
PAGE 321
Command History Version 9.3. (0.0) Introduced on the S4810, S4820T, Z9000 and MXL platforms Usage Information When an ACL-VLAN-Group name or the Access List Group Name contains more than 30 characters, the name is truncated in the show acl-vlan-group command output. Examples The following sample illustrates the output of the show acl-vlan-group command. NOTE: Some group names and some access list names are truncated.
PAGE 322
Group5 Vlan Members : 1,1000 Dell# show cam-acl-vlan Display the number of flow processor (FP) blocks that is allocated for the different VLAN services. Syntax show cam-acl-vlan Command Modes EXEC Privilege Command History Usage Information Version 9.3. (0.0) Introduced on the S4810, S4820T, Z9000 and MXL platforms. After CAM configuration for ACL VLAN groups is performed, you must reboot the system to enable the settings to be stored in nonvolatile storage.
PAGE 323
Example Field Description VlanAclOpt Number of FP blocks for ACL VLAN optimzation feature. Dell#show cam-acl-vlan -- Chassis Vlan Cam ACL -Current Settings(in block sizes) VlanOpenFlow : 0 VlanIscsi : 2 VlanHp : 1 VlanFcoe : 1 VlanAclOpt : 0 -- Stack unit 0 -Current Settings(in block sizes) VlanOpenFlow : 0 VlanIscsi : 2 VlanHp : 1 VlanFcoe : 1 VlanAclOpt : 0 cam-acl-vlan Allocate the number of flow processor (FP) blocks or entries for VLAN services and processes.
PAGE 324
Command History Usage Information Version 9.3(0.0) Introduced on the S4810 and Z9000 platforms. The VLAN ContentAware Processor (VCAP) application is a pre-ingress CAP that modifies the VLAN settings before packets are forwarded. To support the ACL CAM optimization functionality, the CAM carving feature is enhanced. A total of four VACP groups are present, of which two are for fixed groups and the other two are for dynamic groups.
PAGE 325
Example 1: Output of the show camusage Command Field Description LineCard Number of the line card that contains information on ACL VLAN groups Portpipe The hardware path that packets follow through a system for ACL optimization CAM-Region Type of area in the CAM block that is used for ACL VLAN groups Total CAM space Total amount of space in the CAM block Used CAM Amount of CAM space that is currently in use Available CAM Amount of CAM space that is free and remaining to be allocated for ACLs
PAGE 326
| 12286 | | 262127 | | 2834 --More-- | IN-L3 FIB | 262141 | 14 | IN-L3-SysFlow | 2878 | 44 Example 2: Output of the show camusage acl Command Dell#show cam-usage acl Linecard|Portpipe| CAM Partition | Total CAM | |Available CAM ========|========|=================|=============| =============|============ 11 | 0 | IN-L2 ACL | 1008 | 0 | 1008 | | IN-L3 ACL | 12288 | 2 | 12286 | | OUT-L2 ACL | 1024 | 2 | 1022 | | OUT-L3 ACL | 1024 | 0 | 1024 Example 3: Output of the show camusage router Command
PAGE 327
Example 4: Output of the show camusage switch Command Dell#show cam-usage switch Linecard|Portpipe| CAM Partition | Total CAM | |Available CAM ========|========|=================|=============| =============|============== 11 | 0 | IN-L2 ACL | 7152 | | 7152 | | IN-L2 FIB | 32768 | | 31687 | | OUT-L2 ACL | 0 | | 0 11 | 1 | IN-L2 ACL | 7152 | | 7152 | | IN-L2 FIB | 32768 | | 31687 | | OUT-L2 ACL | 0 | | 0 Used CAM 0 1081 0 0 1081 0 show running config acl-vlan-group Display the running configuration of al
PAGE 328
Dell#show running-config acl-vlan-group group1 ! acl-vlan-group group1 description Acl Vlan Group1 member vlan 1-10,400-410,500 ip access-group acl1 out implicit-permit Dell# acl-vlan-group Create an ACL VLAN group. Syntax acl-vlan-group {group name} To remove an ACL VLAN group, use the no acl-vlan-group {group name} command. Parameters group-name Specify the name of the ACL VLAN group. The name can contain a maximum 140 characters.
PAGE 329
show acl-vlan-group detail Display all the ACL VLAN Groups or display a specific ACL VLAN Group by name. To display the names in their entirety, the output displays in a line-by-line format. Syntax Parameters show acl-vlan-group detail detail Display information in a line-by-line format to display the names in their entirety. Without the detail option, the output is displayed in a table style and information may be truncated.
PAGE 330
description (ACL VLAN Group) Add a description to the ACL VLAN group. Syntax Parameters description description description Enter a description to identify the ACL VLAN group (80 characters maximum). Default No default behavior or values Command Modes CONFIGURATION (conf-acl-vl-grp) Command History Usage Information 330 Version 9.3. (0.
PAGE 331
8 Bidirectional Forwarding Detection (BFD) Bidirectional forwarding detection (BFD) is a detection protocol that provides fast forwarding path failure detection. The Dell Networking operating software implementation is based on the standards specified in the IETF Draft draft-ietf-bfd-base-03 and supports BFD on all Layer 3 physical interfaces including VLAN interfaces and port-channels BFD is supported on the Z9000 platform.
PAGE 332
The default is active. Defaults Refer to Parameters. Command Modes ROUTER OSPF ROUTER OSPFv3 ROUTER BGP ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 9.2. (0.
PAGE 333
Related Commands bfd neighbor — Explicitly enables a BFD session with a BGP neighbor or a BGP peer group. neighbor bfd disable — Explicitly disables a BFD session with a BGP neighbor or a BGP peer group. bfd disable Disable BFD on an interface. Z9000 Syntax bfd disable Re-enable BFD using the no bfd disable command. Defaults BFD is disabled by default. Command Modes VRRP Command History This guide is platform-specific.
PAGE 334
Defaults BFD is disabled by default. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.10.0 Introduced on the S4810. Version 8.2.1.0 Introduced on the E-Series ExaScale.
PAGE 335
Version 7.6.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced on the E-Series. bfd interval Specify non-default BFD session parameters beginning with the transmission interval. Z9000 Syntax Parameters bfd interval interval min_rx min_rx multiplier value role {active | passive} interval milliseconds Enter the keywords interval to specify non-default BFD session parameters beginning with the transmission interval. The range is from 50 to 1000. The default is 100.
PAGE 336
Example Version 8.3.10.0 Introduced on the S4810. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced on the E-Series. Dell(conf-if-gi-0/3)#bfd interval 250 min_rx 300 multiplier 4 role passive Dell(conf-if-gi-0/3)# bfd neighbor Establish a BFD session with a neighbor. Z9000 Syntax bfd neighbor ip-address To remove the BFD session with the neighbor, use the no bfd neighbor ipaddress command.
PAGE 337
Version 7.4.1.0 Related Commands Introduced on the E-Series. show bfd neighbors — displays the BFD neighbor information on all interfaces or a specified interface. bfd protocol-liveness Enable the BFD protocol liveness feature. Z9000 Syntax bfd protocol-liveness Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 338
To disable BFD for all neighbors configured through static routes, use the no ip route bfd [interval interval min_rx min_rx multiplier value role {active | passive}] command. Parameters interval milliseconds (OPTIONAL) Enter the keywords interval to specify nondefault BFD session parameters beginning with the transmission interval. The range is from 50 to 1000. The default is 100.
PAGE 339
ipv6 ospf bfd all-neighbors Establish BFD sessions with all OSPFv3 neighbors on a single interface or use non-default BFD session parameters. Z9000 Syntax ipv6 ospf bfd all-neighbors [disable | [interval interval min_rx min_rx multiplier value role {active | passive}]] To disable all BFD sessions on an OSPFv3 interface implicitly, use the no ipv6 ospf bfd all-neighbors disable command in interface mode.. Parameters disable (OPTIONAL) Enter the keyword disable to disable BFD on this interface.
PAGE 340
Usage Information This command provides the flexibility to fine-tune the timer values based on individual interface needs when you configure ipv6 ospf BFD in CONFIGURATION mode. Any timer values specified with this command overrides timers set using the bfd all-neighbors command. Using the no form of this command does not disable BFD if you configure BFD in CONFIGURATION mode. To disable BFD on a specific interface while you configure BFD in CONFIGURATION mode, use the keyword disable.
PAGE 341
Defaults See Parameters Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.0.0 Introduced on Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on S4810. Version 8.2.1.0 Introduced on the E-Series ExaScale.
PAGE 342
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.8.0 Introduced on the S4810. Version 8.4.1.3 Introduced on the E-Series ExaScale.
PAGE 343
peer-groupname Enter the name of the peer group that you want to explicitly disable for BFD sessions. Defaults none Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000.
PAGE 344
Parameters interface Enter one of the following keywords and slot/port or number information: • • • detail Defaults Command Modes Command History For a 10-Gigabit Ethernet interface, enter the keyword tengigabitethernet then the slot/port information. For a port-channel interface, enter the keyword portchannel then a number. For the C-Series, Z-Series, and S8410, the range is from 1 to 128. For VLAN interfaces, enter the keyword vlan then a number from 1 to 4094.
PAGE 345
Example (Detail) Dell#show bfd neighbors detail Related Commands bfd neighbor — establishes a BFD session with a neighbor. Session Discriminator: 1 Neighbor Discriminator: 1 Local Addr: 10.1.3.2 Local MAC Addr: 00:01:e8:02:15:0e Remote Addr: 10.1.3.
PAGE 346
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands 346 Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.10.0 Introduced on the S4810. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the C-Series.
PAGE 347
Border Gateway Protocol 9 BGP is an external gateway protocol that transmits interdomain routing information within and between autonomous systems (AS). BGP version 4 (BGPv4) supports classless inter-domain routing (CIDR) and the aggregation of routes and AS paths. Basically, two routers (called neighbors or peers) exchange information including full routing tables and periodically sent messages to update those routing tables. BGP is supported in Dell Networking OS version 9.0.0.
PAGE 348
Parameters ipv4 multicast Enter the keyword ipv4 followed by the keyword multicast to enable BGPv4 multicast mode. ipv6 unicast Enter the keyword ipv6 followed by the keyword unicast to enable BGPv6 mode. Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 349
attribute-map map-name (OPTIONAL) Enter the keywords attribute-map then the name of a configured route map to modify attributes of the aggregate, excluding AS_PATH and NEXT_HOP attributes. summary-only (OPTIONAL) Enter the keyword summary-only to advertise only the aggregate address. Specific routes are not advertised. suppress-map map-name (OPTIONAL) Enter the keywords suppress-map then the name of a configured route map to identify which morespecific routes in the aggregate are suppressed.
PAGE 350
In the show ip bgp command, aggregates contain an ‘a’ in the first column and routes suppressed by the aggregate contain an ‘s’ in the first column. When an aggregate address is denied using a peer's outbound route-map, individual routes suppressed by the aggregate address are advertised to that peer.
PAGE 351
Related Commands neighbor add-path — specifies that this neighbor/peer group can send/receive multiple path advertisements. bgp always-compare-med Allows you to enable comparison of the MULTI_EXIT_DISC (MED) attributes in the paths from different external ASs. Z9000 Syntax bgp always-compare-med To disable comparison of MED, enter no bgp always-compare-med. Defaults Disabled (that is, the software only compares MEDs from neighbors within the same AS).
PAGE 352
Defaults asplain Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.
PAGE 353
Related Commands bgp four-octet-as-support — enables 4-byte support for the BGP process. bgp bestpath as-path ignore Ignore the AS PATH in BGP best path calculations. Z9000 Syntax bgp bestpath as-path ignore To return to the default, enter the no bgp bestpath as-path ignore command. Defaults Disabled (that is, the software considers the AS_PATH when choosing a route as best). Command Modes ROUTER BGP Command History This guide is platform-specific.
PAGE 354
Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.4 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810.
PAGE 355
Version 7.7.1.0 Usage Information Introduced on the C-Series. The software compares the MEDs only if the path contains no external autonomous system numbers. If you enable this command, use the clear ip bgp * command to recompute the best path. bgp bestpath med missing-as-best During path selection, indicate preference to paths with missing MED (MULTI_EXIT_DISC) over paths with an advertised MED attribute.
PAGE 356
bgp bestpath router-id ignore Do not compare router-id information for external paths during best path selection. Z9000 Syntax bgp bestpath router-id ignore To return to the default selection, use the no bgp bestpath router-id ignore command. Defaults Disabled Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 357
The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Usage Information Route reflection to clients is not necessary if all client routers are fully meshed.
PAGE 358
Usage Information Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. When a BGP cluster contains only one route reflector, the cluster ID is the route reflector’s router ID. For redundancy, a BGP cluster may contain two or more route reflectors. Assign a cluster ID with the bgp cluster-id command.
PAGE 359
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Added support for the 4-byte format To accept 4-byte formats before entering a 4-byte AS number, configure your system. All the routers in the Confederation must be 4 byte or 2 byte identified routers. You cannot mix them.
PAGE 360
Parameters as-number Enter the AS number. The range is from 0 to 65535 (2 byte), from 1 to 4294967295 (4 byte), or from 0.1 to 65535.65535 (dotted format). ...as-number (OPTIONAL) Enter up to 16 confederation numbers. The range is from 0 to 65535 (2 byte), from 1 to 4294967295 (4 byte), or from 0.1 to 65535.65535 (dotted format). Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific.
PAGE 361
bgp dampening Enable BGP route dampening and configure the dampening parameters. Z9000 Syntax bgp dampening [half-life reuse suppress max-suppress-time] [route-map map-name] To disable route dampening, use the no bgp dampening [half-life reuse suppress max-suppress-time] [route-map map-name] command. Parameters half-life (OPTIONAL) Enter the number of minutes after which the Penalty is decreased.
PAGE 362
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. If you enter the bgp dampening command, the default values for half-life, reuse, suppress, and max-suppress-time are applied.
PAGE 363
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Usage Information All routers apply the bgp default local-preference command setting within the AS. To set the local preference for a specific route, use the set localpreference command in ROUTE-MAP mode.
PAGE 364
peer. If not, the update is dropped and a counter is increments. Use the show ip bgp neighbors command to view the “failed enforce-first-as check” counter. If you disable the enforce-first-as command, it can be viewed using the show ip protocols command. In the event of an enfore-first-as check failure, the existing BGP session is flapped. Related Commands show ip bgp neighbors — views the information the BGP neighbors exchange. show ip protocols — views information on routing protocols.
PAGE 365
also manually execute the clear ip bgp command in order for the configuration to take effect. bgp four-octet-as-support Enable 4-byte support for the BGP process. Z9000 Syntax bgp four-octet-as-support To disable fast external failover, use the no bgp four-octet-as-support command. Defaults Disabled (supports 2–byte format) Command Modes ROUTER BGP Command History This guide is platform-specific.
PAGE 366
This command automatically restarts the BGP instance for the configuration to take effect. bgp graceful-restart To support graceful restart as a receiver only, enable graceful restart on a BGP neighbor, a BGP node, or designate a local router. Z9000 Syntax bgp graceful-restart [restart-time seconds] [stale-path-time seconds] [role receiver-only] To return to the default, use the no bgp graceful-restart command.
PAGE 367
BGP graceful restart is active only when the neighbor becomes established. Otherwise it is disabled. Graceful-restart applies to all neighbors with established adjacency. This command automatically restarts the BGP instance for the configuration to take effect. bgp log-neighbor-changes Enable logging of BGP neighbor resets. Z-SeriesS6000 Syntax bgp log-neighbor-changes To disable logging, use the no bgp log-neighbor-changes command.
PAGE 368
Defaults Disabled (that is, paths/routes for the same destination but from different ASs do not have their MEDs compared). Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T.
PAGE 369
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.
PAGE 370
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Version 7.6.1.0 Introduced BGP uses regular expressions (regex) to filter route information. In particular, the use of regular expressions to filter routes based on AS-PATHs and communities is common.
PAGE 371
bgp router-id Assign a user-given ID to a BGP router. Z9000 Syntax bgp router-id ip-address To delete a user-assigned IP address, use the no bgp router-id command. Parameters ip-address Enter an IP address in dotted decimal format to reset only that BGP neighbor. Defaults The router ID is the highest IP address of the Loopback interface or, if no Loopback interfaces are configured, the highest IP address of a physical interface on the router.
PAGE 372
Parameters * Enter an asterisk ( * ) to reset all BGP sessions. as-number Enter the AS number to reset all neighbors belonging to that AS. The range is from 0 to 65535 (2 byte), from 1 to 4294967295 (4 byte), or from 0.1 to 65535.65535 (dotted format). ip-address Enter an IP address in dotted decimal format to reset all prefixes from that neighbor. flap-statistics (OPTIONAL) Enter the keyword flap-statistics to reset the flap statistics on all prefixes from that neighbor.
PAGE 373
peer-group Enter the peer-group to clear all members of the peergroup. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000.
PAGE 374
Usage Information Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. After you enter this command, the software deletes the history routes and returns the suppressed routes to the Active state. The clear ip bgp dampening command does not clear the history paths. clear ip bgp flap-statistics Clear BGP flap statistics, which includes number of flaps and the time of the last flap.
PAGE 375
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series.
PAGE 376
Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. debug ip bgp Display all information on BGP, including BGP events, keepalives, notifications, and updates. Z9000 Syntax debug ip bgp [ip-address | peer-group peer-group-name] [in | out] To disable all BGP debugging, use the no debug ip bgp command. Parameters ip-address Enter the IP address of the neighbor in dotted decimal format.
PAGE 377
The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. To view information on both incoming and outgoing routes, do not include the in and out parameters in the debugging command.
PAGE 378
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.
PAGE 379
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. To remove all configured debug commands for BGP, enter the no debug ip bgp command. debug ip bgp keepalives Display information about BGP keepalive messages.
PAGE 380
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. To remove all configured debug commands for BGP, enter the no debug ip bgp command. debug ip bgp notifications Allows you to view information about BGP notifications received from neighbors.
PAGE 381
Usage Information Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. To remove all configured debug commands for BGP, enter the no debug ip bgp command. debug ip bgp soft-reconfiguration Enable soft-reconfiguration debug. Z9000 S6000 Syntax debug ip bgp {ip-address | peer-group-name} softreconfiguration To disable, use the no debug ip bgp {ip-address | peer-group-name} soft-reconfiguration command.
PAGE 382
Usage Information This command turns on BGP soft-reconfiguration inbound debugging. If no neighbor is specified, debug turns on for all neighbors. debug ip bgp updates Allows you to view information about BGP updates. Z9000 Syntax debug ip bgp updates [in | out | prefix-list prefix-list-name] To disable debugging, use the no debug ip bgp [ip-address | peer-group peer-group-name] updates [in | out] command. Parameters in (OPTIONAL) Enter the keyword in to view only BGP updates received from neighbors.
PAGE 383
Usage Information To remove all configured debug commands for BGP, enter the no debug ip bgp command. default-metric Allows you to change the metric of redistributed routes to locally originated routes. Use this command with the redistribute command. Z9000 Syntax default-metric number To return to the default setting, use the no default-metric command. Parameters number Enter a number as the metric to be assigned to routes from other protocols. The range is from 1 to 4294967295.
PAGE 384
description Enter a description of the BGP routing protocol Z9000 Syntax description {description} To remove the description, use the no description {description} command. Parameters description Enter a description to identify the BGP protocol (80 characters maximum). Defaults none Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 385
Parameters Defaults externaldistance Enter a number to assign to routes learned from a neighbor external to the AS. The range is from 1 to 255. The default is 20. internaldistance Enter a number to assign to routes learned from a router within the AS. The range is from 1 to 255. The default is 200. local-distance Enter a number to assign to routes learned from networks listed in the network command. The range is from 1 to 255. The default is 200.
PAGE 386
Parameters ebgp Enter the keyword ebgp to enable multipath support for External BGP routes. ibgp Enter the keyword ibgp to enable multipath support for Internal BGP routes. number Enter a number as the maximum number of parallel paths. Defaults none Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 387
activate Enter the keyword activate to enable the neighbor/peer group in the new AFI/SAFI. Defaults Disabled Command Modes CONFIGURATION-ROUTER-BGP-ADDRESS FAMILY Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 388
path-count Enter the number paths supported. The range is from 2 to 64. Defaults none Command Modes CONFIGURATION-ROUTER-BGP-ADDRESS FAMILY Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T.
PAGE 389
Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.
PAGE 390
Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. neighbor allowas-in Set the number of times an AS number can occur in the AS path. Z-Series Syntax neighbor {ip-address | peer-group-name} allowas-in number To return to the default value, use the no neighbor {ip-address | peergroup-name} allowas-in command.
PAGE 391
Related Commands bgp four-octet-as-support — enables 4-byte support for the BGP process. neighbor default-originate Inject the default route to a BGP peer or neighbor. Z-Series Syntax neighbor {ip-address | peer-group-name} default-originate [route-map map-name] To remove a default route, use the no neighbor {ip-address | peergroup-name} default-originate command. Parameters ip-address (OPTIONAL) Enter the IP address of the neighbor in dotted decimal format.
PAGE 392
Route-map configuration on a BGP peer or peer group works only when the LOCRIB contains at least one route. When you apply a default route to a BGP peer or peer group using the neighbor default-originate command, changes to the configured default route-map are applied to the BGP peer or peer group only after a delay of 15 seconds. As a result, you must wait for a period of 15 seconds before manually resetting BGP using the clear ip bgp command.
PAGE 393
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. neighbor distribute-list Distribute BGP information via an established prefix list.
PAGE 394
Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Usage Information Other BGP filtering commands include: neighbor filter-list, ip as-path access-list, and neighbor route-map. Related Commands ip as-path access-list — configures IP AS-Path ACL. neighbor route-map — assigns a route map to a neighbor or peer group.
PAGE 395
Version 7.7.1.0 Usage Information Introduced on the C-Series. To prevent loops, the neighbor ebgp-multihop command does not install the default routes of the multihop peer. Networks not directly connected are not considered valid for best-path selection. neighbor fall-over Enable or disable fast fall-over for BGP neighbors. Z-Series Syntax neighbor {ipv4-address | peer-group-name} fall-over To disable, use the no neighbor {ipv4-address | peer-group-name} fall-over command.
PAGE 396
Related Commands show ip bgp neighbors — displays information on the BGP neighbors. neighbor filter-list Configure a BGP filter based on the AS-PATH attribute. Z-Series Syntax neighbor {ip-address | peer-group-name} filter-list as-pathname {in | out} To delete a BGP filter, use the no neighbor {ip-address | peer-groupname} filter-list as-path-name {in | out} command. Parameters ip-address Enter the IP address of the neighbor in dotted decimal format.
PAGE 397
Usage Information To enter AS-PATH ACL mode and configure the AS-PATH filters to deny or permit BGP routes based on information in their AS-PATH attribute, use the ip as-path access-list command in CONFIGURATION mode. Related Commands ip as-path access-list — enter AS-PATH ACL mode and configure the AS-PATH filters. neighbor local-as To accept external routes from neighbors with a local AS number in the AS number path, configure Internal BGP (IBGP) routers.
PAGE 398
Version 7.7.1.0 Usage Information Introduced on the C-Series. If a local-as is configured, BGP does not allow for the configuration of BGP confederation. Similarly, if BGP confederation is configured, then BGP does not allow the configuration of local-as. This command automatically restarts the neighbor session for the configuration to take effect. Related Commands bgp four-octet-as-support — enables 4-byte support for the BGP process.
PAGE 399
Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.
PAGE 400
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant FTOS Command Line Reference Guide. The following is a list of the FTOS version history for this command. Usage Information Version 8.3.11.1 Introduced on the Z9000. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series.
PAGE 401
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. This command automatically restarts the neighbor session for the configuration to take effect. Configure the same password on both BGP peers or a connection does not occur.
PAGE 402
peer-groupname Enter the name of a configured peer group. Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.
PAGE 403
show ip bgp peer-group — views BGP peers. show ip bgp neighbors — views BGP neighbors configurations. neighbor peer-group (creating group) Allows you to create a peer group and assign it a name. Z-Series Syntax neighbor peer-group-name peer-group To delete a peer group, use the no neighbor peer-group-name peer-group command. Parameters peer-groupname Enter a text string up to 16 characters long as the name of the peer group. Defaults Not configured.
PAGE 404
neighbor peer-group passive Enable passive peering on a BGP peer group, that is, the peer group does not send an OPEN message, but responds to one. Z-Series Syntax neighbor peer-group-name peer-group passive [sessions] To delete a passive peer-group, use the no neighbor peer-group-name peer-group passive command. Parameters peer-groupname Enter a text string up to 16 characters long as the name of the peer group. Defaults Not configured.
PAGE 405
neighbor remote-as Create and specify the remote peer to the BGP neighbor. Z-Series Syntax neighbor {ip-address | peer-group-name} remote-as number To delete a remote AS entry, use the no neighbor {ip-address | peergroup-name} remote-as number command. Parameters ip-address Enter the IP address of the neighbor to enter the remote AS in its routing table. peer-groupname Enter the name of the peer group to enter the remote AS into routing tables of all routers within the peer group.
PAGE 406
bgp four-octet-as-support — enables 4-byte support for the BGP process. neighbor remove-private-as Remove private AS numbers from the AS-PATH of outgoing updates. Z-Series Syntax neighbor {ip-address | peer-group-name} remove-private-as To return to the default, use the no neighbor {ip-address | peer-groupname} remove-private-as command. Parameters ip-address Enter the IP address of the neighbor to remove the private AS numbers.
PAGE 407
Private AS numbers are from 64512 to 65535 (2 byte). neighbor route-map Apply an established route map to either incoming or outbound routes of a BGP neighbor or peer group. Z-Series Syntax neighbor {ip-address | peer-group-name} route-map map-name {in | out} To remove the route map, use the no neighbor {ip-address | peergroup-name} route-map map-name {in | out} command. Parameters ip-address Enter the IP address of the neighbor in dotted decimal format.
PAGE 408
Version 7.7.1.0 Usage Information Introduced on the C-Series. When you apply a route map to outbound routes, only routes that match at least one section of the route map are permitted. If you identify a peer group by name, the peers in that peer group inherit the characteristics in the Route map used in this command. If you identify a peer by IP address, the Route map overwrites either the inbound or outbound policies on that peer.
PAGE 409
Version 7.7.1.0 Usage Information Introduced on the C-Series. A route reflector reflects routes to the neighbors assigned to the cluster. Neighbors in the cluster do not need not to be fully meshed. By default, when you use no route reflector, the internal BGP (IBGP) speakers in the network must be fully meshed. The first time you enter this command, the router configures as a route reflector and the specified BGP neighbors configure as clients in the route-reflector cluster.
PAGE 410
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.11.1 Introduced on the Z9000. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series.
PAGE 411
Usage Information Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Peers that are enabled within a peer group are disabled when their peer group is disabled. The neighbor shutdown command terminates all BGP sessions on the BGP neighbor or BGP peer group. Use this command with caution as it terminates the specified BGP sessions.
PAGE 412
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced. This command enables soft-reconfiguration for the BGP neighbor specified. BGP stores all the updates the neighbor receives but does not reset the peer-session.
PAGE 413
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 8.3.11.1 Introduced on the Z9000. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. neighbor timers Set keepalive and hold time timers for a BGP neighbor or a peer group.
PAGE 414
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Timer values configured with the neighbor timers command override the timer values configured with any other command.
PAGE 415
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Loopback interfaces are up constantly and the BGP session may need one interface constantly up to stabilize the session. The neighbor update-source command is not necessary for directly connected internal BGP sessions.
PAGE 416
Usage Information Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. In the Dell Networking OS best path selection process, the path with the highest weight value is preferred. NOTE: In the Dell Networking OS best-path selection process, the path with the highest weight value is preferred.
PAGE 417
• set origin • set weight If the route map is not configured, the default is deny (to drop all routes). Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 418
network backdoor Specify this IGP route as the preferred route. Z-Series Syntax network ip-address mask backdoor To remove a network, use the no network ip-address mask backdoor command. Parameters ip-address Enter an IP address in dotted decimal format of the network. mask Enter the mask of the IP address in the slash prefix length format (for example, /24). The mask appears in command outputs in dotted decimal format (A.B.C.D). Defaults Not configured.
PAGE 419
redistribute Redistribute routes into BGP. Z-Series Syntax redistribute {connected | static} [route-map map-name] To disable redistribution, use the no redistribution {connected | static} command. Parameters connected Enter the keyword connected to redistribute routes from physically connected interfaces. static Enter the keyword static to redistribute manually configured routes. These routes are treated as incomplete routes.
PAGE 420
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Introduced the ability to substitute IGP cost for MED when a peer/peer-group outbound route-map is set as internal. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. You can use the redistribute command to advertise the IGP cost as the MED on redistributed routes.
PAGE 421
Parameters process-id Enter the number of the OSPF process. The range is from 1 to 65535. match external {1 | 2} (OPTIONAL) Enter the keywords match external to redistribute OSPF external routes. You can specify 1 or 2 to redistribute those routes only. match internal (OPTIONAL) Enter the keywords match internal to redistribute OSPF internal routes only. route-map map-name (OPTIONAL) Enter the keywords route-map then the name of a configured route map. Defaults Not configured.
PAGE 422
router bgp To configure and enable BGP, enter ROUTER BGP mode. Z-Series Syntax router bgp as-number To disable BGP, use the no router bgp as-number command. Parameters as-number Enter the AS number. The range is from 1 to 65535 (2 byte), from 1 to 4294967295 (4 byte), or from 0.1 to 65535.65535 (dotted format). Defaults Not enabled. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 423
show capture bgp-pdu neighbor Display BGP packet capture information for an IPv4 address on the system. Z-Series Syntax Parameters show capture bgp-pdu neighbor ipv4-address ipv4-address Enter the IPv4 address (in dotted decimal format) of the BGP address to display packet information for that address. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 424
14141401 0c020a01 04000100 01020080 00000000 PDU[2] : len 19, captured 00:34:51 ago ffffffff ffffffff ffffffff ffffffff 00130400 PDU[3] : len 19, captured 00:34:50 ago ffffffff ffffffff ffffffff ffffffff 00130400 [. . .] Dell# show config View the current ROUTER BGP configuration. Z-Series Syntax show config Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 425
Parameters ipv4 unicast (OPTIONAL) Enter the keywords ipv4 unicast to view information only related to ipv4 unicast routes. network (OPTIONAL) Enter the network address (in dotted decimal format) of the BGP network to view information only on that network. network-mask (OPTIONAL) Enter the network mask (in slash prefix format) of the BGP network address. longer-prefixes (OPTIONAL) Enter the keywords longer-prefixes to view all routes with a common prefix.
PAGE 426
Example Field Description LocPrf Displays the BGP LOCAL_PREF attribute for the route. Weight Displays the route’s weight. Path Lists all the ASs the route passed through to reach the destination network. Dell#show ip bgp BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.
PAGE 427
Usage Information Example Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. The following describes the show ip bgp cluster-list command shown in the following example. Field Description Network Displays the destination network prefix of each BGP route. Next Hop Displays the next hop address of the BGP router. If 0.0.0.
PAGE 428
Weight Path *>I 55.0.0.0/24 172.16.0.2 0 0 400 500 600 i *>I 66.0.0.0/24 172.16.0.2 0 0 500 i *>I 77.0.0.0/24 172.16.0.2 0 0 i Dell# show ip bgp community View information on all routes with Community attributes or view specific BGP community groups. Z-Series Syntax Parameters show ip bgp [ipv4 unicast] community [community-number] [localas] [no-export] [no-advertise] ipv4 unicast (OPTIONAL) Enter the keywords ipv4 unicast to view information only related to ipv4 unicast routes.
PAGE 429
Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.
PAGE 430
aa:nn | Community number in aa:nn format Pipe through a command Dell#show ip bgp community BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.5 Status codes: s suppressed, S stale, d dampened, h history, * valid, > best Path source: I - internal, a - aggregate, c - confed-external, r - redistributed n - network, D - denied, S - stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Weight Path *> 55.0.0.0/24 172.16.0.2 *> 66.0.0.0/24 172.16.0.
PAGE 431
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.
PAGE 432
172.16.0.2 0 200 i Dell#show ip bgp 55.0.0.0/24 BGP routing table entry for 55.0.0.0/24 Paths: (1 available, table Default-IP-Routing-Table.) Not advertised to any peer Received from : 172.16.0.2 (172.16.0.2) AS_PATH : 200 Best Next-Hop : 172.16.0.2, Cost : 0 Origin IGP, Metric 4294967295 (Default), LocalPref Weight 0, external Communities : 200:1 1000:1 100, 3000:1 show ip bgp dampened-paths View BGP routes that are dampened (non-active).
PAGE 433
route-up event corresponding to the same route is not considered as a flap and is not penalized. The history paths that the show ip bgp command displays contain only the prefix and the next-hop information. The next-hop information shows the ip address of the neighbor. It does not show the actual next-hop details. The following describes the show ip bgp damp command shown in the following example. Example Field Description Network Displays the network ID to which the route is dampened.
PAGE 434
Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Version 7.5.1.0 Introduced.
PAGE 435
PeerUpdTmrP 0x41ee70cc : DfrdNHTmrP 0x41ee7174 : DfrdRtselTmrP 0x41ee713c : FastExtFallover 1 : FastIntFallover 0 : Enforce1stAS 1 PeerIdBitsP 0x41967120 : softOutSz 16 : RibUpdCtxCBP 0 UpdPeerCtxCBP 0 : UpdPeerCtxAFI 0 : TcpioCtxCB 0 : RedistBlk 1 NextCBPurg 1101119536 : NumPeerToPurge 0 : PeerIBGPCnt 0 : NonDet 0 : DfrdPathSel 0 BGPRst 0 : NumGrCfg 1 : DfrdTmestmp 0 : SnmpTrps 0 : IgnrBestPthASP 0 RstOn 1 : RstMod 1 : RstRole 2 : AFFalgs 7 : RstInt 120 : MaxeorExtInt 361 FixedPartCrt 1 : VarParCrt 1 Packe
PAGE 436
Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.
PAGE 437
show ip bgp filter-list View the routes that match the filter lists. Z-Series Syntax Parameters show ip bgp [ipv4 unicast] filter-list as-path-name ipv4 unicast (OPTIONAL) Enter the keywords ipv4 unicast to view information only related to ipv4 unicast routes. as-path-name Enter an AS-PATH access list name. The range is 140 characters. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific.
PAGE 438
Example Field Description Next Hop Displays the next hop address of the BGP router. If 0.0.0.0 is listed in this column, then local routes exist in the routing table. Metric Displays the BGP route’s metric, if assigned. LocPrf Displays the BGP LOCAL_PREF attribute for the route. Weight Displays the route’s weight. Path Lists all the ASs the route passed through to reach the destination network.
PAGE 439
filter-list aspath-name (OPTIONAL) Enter the keyword filter-list then the name of a configured AS-PATH ACL. The range is 140 characters. regexp regularexpression Enter a regular expression then use one or a combination of the following characters to match. The range is 256 characters. • . = (period) any single character (including a white space). • * = (asterisk) the sequences in a pattern (zero or more sequences). • + = (plus) the sequences in a pattern (one or more sequences).
PAGE 440
Example Field Description Network Displays the network ID to which the route is flapping. From Displays the IP address of the neighbor advertising the flapping route. Flaps Displays the number of times the route flapped. Duration Displays the hours:minutes:seconds since the route first flapped. Reuse Displays the hours:minutes:seconds until the flapped route is available. Path Lists all the ASs the flapping route passed through to reach the destination network.
PAGE 441
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.
PAGE 442
* * * 6.0.0.0/20 * *> * * 9.2.0.0/16 * --More-- 63.114.8.33 63.114.8.33 63.114.8.60 63.114.8.34 63.114.8.33 63.114.8.33 63.114.8.60 63.114.8.34 0 0 0 0 0 0 0 0 0 18508 18508 18508 18508 18508 18508 18508 18508 701 209 209 209 ? 209 209 209 1 i 1 i 3549 i 3549 i 3549 i 701 i 701 i Dell>sho ip bgp vrf testinconsistent-as BGP table version is 11, local router ID is 66.66.77.
PAGE 443
detail (OPTIONAL) Enter the keyword detail to view neighborspecific internal information for the IPv4 Unicast address family. flap-statistics (OPTIONAL) Enter the keywords flap-statistics to view flap statistics on the neighbor’s routes. routes (OPTIONAL) Enter the keyword routes to view only the neighbor’s feasible routes.
PAGE 444
Usage Information After a peer reset, the contents of the notification log messages is displayed in hex values for debugging. The neighbor information that this command displays does not include counts corresponding to ignored prefixes and updates. However, the martian case is an exception where neighbor information corresponding to ignored updates is displayed. BGP shows the exact information that is exchanged between the BGP peers.
PAGE 445
Example The Lines Beginning with: Description Minimum time Displays the minimum time, in seconds, between advertisements. (list of inbound and outbound policies) Displays the policy commands configured and the names of the Route map, AS-PATH ACL, or Prefix list configured for the policy. For address family: Displays the IPv4 Unicast as the address family. BGP table version Displays which version of the primary BGP routing table the router and the neighbor are using.
PAGE 446
Capabilities advertised to neighbor for IPv4 Unicast : MULTIPROTO_EXT(1) ROUTE_REFRESH(2) ADD_PATH(69) CISCO_ROUTE_REFRESH(128) For address family: IPv4 Unicast BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 InQ : Added 0, Replaced 0, Withdrawn 0 OutQ : Added 0, Withdrawn 0 Allow local AS number 0 times in AS-PATH attribute Prefixes accepted 2, withdrawn 15 by peer, martian prefixes ignored 0 Prefixes advertised 0, denied 0, withdrawn 0 from peer Connections established 1; dropped 0 Last res
PAGE 447
Usage Information Example Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. The following describes the show ip bgp next-hop command shown in the following example. Field Description Next-hop Displays the next-hop IP address. Via Displays the IP address and interface used to reach the next hop. RefCount Displays the number of BGP routes using this next hop. Cost Displays the cost associated with using this next hop.
PAGE 448
• { } = (braces) minimum and the maximum match count. • ^ = (caret) the beginning of the input string. If you use the caret at the beginning of a sequence or range, it matches on everything BUT the characters specified. $ = (dollar sign) the end of the output string. • Command Modes Command History • • EXEC EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 449
Dell#show ip bgp paths Total 2 Paths Refcount Metric Path 1 0 200 i 1 0 200 i show ip bgp paths community View all unique COMMUNITY numbers in the BGP database. Z-Series Syntax show ip bgp paths community Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 450
1 1 NO-ADVERTISE 200:1 1000:1 3000:1 show ip bgp peer-group Allows you to view information on the BGP peers in a peer group. Z-Series Syntax Parameters show ip bgp [ipv4 unicast] peer-group [peer-group-name [detail | summary]] ipv4 unicast (OPTIONAL) Enter the keywords ipv4 unicast to view information only related to ipv4 unicast routes. peer-groupname (OPTIONAL) Enter the name of a peer group to view information about that peer group only.
PAGE 451
Example Line beginning with: Description Peer-group Displays the peer group’s name. Administratively shut Displays the peer group’s status if the peer group is not enabled. If you enable the peer group, this line is not displayed. BGP version Displays the BGP version supported. Minimum time Displays the time interval between BGP advertisements. For address family Displays IPv4 Unicast as the address family. BGP neighbor Displays the name of the BGP neighbor.
PAGE 452
• * = (asterisk) the sequences in a pattern (zero or more sequences). • + = (plus) the sequences in a pattern (one or more sequences). • ? = (question mark) sequences in a pattern (either zero or one sequences). NOTE: Enter an escape sequence (CTRL+v) prior to entering the ? regular expression. • [ ] = (brackets) a range of single-character patterns. • ( ) = (parenthesis) groups a series of pattern elements to a single element. • { } = (braces) minimum and the maximum match count.
PAGE 453
Example Field Description LocPrf Displays the BGP LOCAL_PREF attribute for the route. Weight Displays the route’s weight Path Lists all the AS paths the route passed through to reach the destination network. Dell#show ip bgp regexp ^200 BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.
PAGE 454
Usage Information Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. In BGP, route attributes are maintained at different locations. When attributes that correspond to multiple routes change, then attribute counts that the show ip bgp summary command displays are calculated as summations of attributes corresponding to all the associated routes.
PAGE 455
Field Description Dampening enabled Displayed only when you enable dampening. Displays the number of paths designated as history, dampened, or penalized. Neighbor Displays the BGP neighbor address. AS Displays the AS number of the neighbor. MsgRcvd Displays the number of BGP messages that neighbor received. MsgSent Displays the number of BGP messages that neighbor sent. TblVer Displays the version of the BGP table that was sent to that neighbor.
PAGE 456
Field Description If the neighbor is disabled, the phrase (Admin shut) appears in this column. Example (S4810) Dell#show ip bgp summary BGP router identifier 192.168.11.
PAGE 457
Example Dell#show running-config bgp ! router bgp 100 network 1.1.11.1/32 network 1.1.12.1/32 network 1.1.13.1/32 neighbor 10.1.1.2 remote-as 200 neighbor 10.1.1.2 no shutdown Dell# timers bgp Adjust the BGP Keep Alive and Hold Time timers. Z-Series Syntax timers bgp keepalive holdtime To return to the default, use the no timers bgp command. Parameters keepalive Enter a number for the time interval, in seconds, between keepalive messages sent to the neighbor routers. The range is from 1 to 65535.
PAGE 458
MBGP Commands Multiprotocol BGP (MBGP) is an enhanced BGP that enables multicast routing policy throughout the internet and connecting multicast topologies between BGP and autonomous systems (ASs). Dell Networking OS MBGP is implemented as per IETF RFC 1858. BGPv4 is supported in the following: Dell Networking OS Version Platform Support 7.8.1.0, MBGP for S-Series IPv4 Multicast Only debug ip bgp dampening View information on routes being dampened.
PAGE 459
distance bgp Configure three administrative distances for routes. Syntax distance bgp external-distance internal-distance local-distance To return to default values, use the no distance bgp command. Parameters Defaults externaldistance Enter a number to assign to routes learned from a neighbor external to the AS. The range is from 1 to 255. The default is 20. internaldistance Enter a number to assign to routes learned from a router within the AS. The range is from 1 to 255. The default is 200.
PAGE 460
Related Commands router bgp — enters ROUTER mode on the switch. show ip bgp dampened-paths View BGP routes that are dampened (non-active). Z-Series Syntax Parameters Command Modes Command History show ip bgp [ipv4 unicast] dampened-paths ipv4 unicast • EXEC • EXEC Privilege (OPTIONAL) Enter the keywords ipv4 unicast to view information only related to ipv4 unicast routes. This guide is platform-specific.
PAGE 461
Example Field Description From Displays the IP address of the neighbor advertising the dampened route. Reuse Displays the hour:minutes:seconds until the dampened route is available. Path Lists all the ASs the dampened route passed through to reach the destination network. Dell#show ip bgp dampened-paths BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.
PAGE 462
soo Enter the keyword soo to designate a Site-of-Origin community (also known as Route Origin). as4 ASN4:NN Enter the keyword as4 then the 4-octet AS specific extended community number in the format ASN4:NN (4byte AS number:2-byte community value). ASN:NNNN Enter the 2-octet AS specific extended community number in the format ASN:NNNN (2-byte AS number:4-byte community value).
PAGE 463
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Version 7.6.1.0 Introduced on the E-Series. Usage Information Duplicate commands are silently accepted.
PAGE 464
ip extcommunity-list To enter the Extended Community-list mode, use this feature. Z-Series Syntax ip extcommunity-list word To exit from this mode, use the exit command. Parameters word Enter a community list name (maximum 16 characters). Defaults none Command Modes CONFIGURATION (conf-ext-community-list) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 465
Command Modes ROUTE MAP (config-route-map) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Version 7.6.1.0 Introduced on the E-Series.
PAGE 466
Command Modes CONFIGURATION (conf-ext-community-list) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Version 7.6.1.0 Introduced on the E-Series. deny — configures to delete (deny) rules.
PAGE 467
Related Commands deny regex — denies a community using a regular expression. set extcommunity rt To set Route Origin community attributes in Route Map, use this feature. Z-Series Syntax set extcommunity rt {as4 ASN4:NN [non-trans] | ASN:NNNN [nontrans] | IPADDR:NN [non-trans]} [additive] To delete the Route Origin community, use the no set extcommunity command.
PAGE 468
Usage Information Related Commands If the set community rt and soo are in the same route-map entry, the behavior defines as: • If the rt option comes before soo, with or without the additive option, soo overrides the communities rt sets. • If the rt option comes after soo, without the additive option, rt overrides the communities soo sets. • If the rt with the additive option comes after soo, rt adds the communities soo sets.
PAGE 469
Usage Information Related Commands Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Version 7.6.1.0 Introduced on the E-Series. If the set community rt and soo are in the same route-map entry, the behavior defines as: • If the rt option comes before soo, with or without the additive option, soo overrides the communities rt sets.
PAGE 470
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Version 7.6.1.0 Introduced on the E-Series. If there is a type or sub-type that is not well-known, it is displayed as:TTSS:XX:YYYY. Where TT is type, SS is sub-type displayed in hexadecimal format, XX:YYYY is the value divided into 2–byte and 4-byte values in decimal format. This format is consistent with other vendors.
PAGE 471
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series.
PAGE 472
Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 8.3.19.0 Introduced on the S4820T. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Version 7.6.1.
PAGE 473
Example Dell#show running-config extcommunity-list test ip extcommunity-list test permit rt 65033:200 deny soo 101.11.11.2:23 permit rt as4 110212:340 deny regex ^(65001_)$ Dell# IPv6 BGP Commands IPv6 border gateway protocol (IPv6 BGP) is supported on the Z-Series platform. BGP is an external gateway protocol that transmits interdomain routing information within and between Autonomous Systems (AS).
PAGE 474
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 8.3.19.0 Introduced on the S4820T. Version 8.4.1.0 Added support for IPv4 multicast and IPv6 unicast routes. Version 7.8.1.0 Introduced on the S4810. Version 7.7.1.0 Introduced on the C-Series. Version 7.2.1.
PAGE 475
Usage Information Version 7.8.1.0 Introduced on the S4810. Version 7.7.1.0 Introduced on the C-Series. Version 7.2.1.0 Introduced on the E-Series TeraScale. This command turns on BGP soft-reconfiguration inbound debugging for IPv6 unicast routes. If no neighbor is specified, debug is turned on for all neighbors. ipv6 prefix-list Configure an IPv6 prefix list. Z-Series Syntax Parameters ipv6 prefix-list prefix-list name prefix-list name Enter the name of the prefix list.
PAGE 476
Parameters ipv4-address | ipv6-address Enter the IP address of the neighbor for which you want to start storing inbound routing updates. peer-groupname Enter the name of the peer group for which you want to start storing inbound routing updates. Defaults Disabled. Command Modes ROUTER BGPv6 ADDRESS FAMILY (conf-router_bgpv6_af) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 477
Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant FTOS Command Line Reference Guide. The following is a list of the FTOS version history for this command. Related Commands Version 9.0.0.0 Introduced on the Z9000. Version 8.3.10.0 Introduced on the S4810. ipv6 prefix-list — configures an IPv6 prefix-list.
PAGE 478
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.10.0 Introduced on the S4810.
PAGE 479
Content Addressable Memory (CAM) 10 Content addressable memory (CAM) commands are supported on the Dell Networking Z9000 platform. NOTE: Not all CAM commands are supported on all platforms. Be sure to note the platform when looking for a command. WARNING: If you are using these features for the first time, contact Dell Networking Technical Assistance Center (TAC) for guidance. CAM Profile Commands The CAM profiling feature allows you to partition the CAM to best suit your application.
PAGE 480
validation for DHCP, Ethernet Connectivity Fault Management (CFM) ACLs, OpenFlow, and Policy-based Routing (PBR).
PAGE 481
Vman-qos| vman-dual-qos number Enter the keyword evman-qos and then the number of FP blocks for VMAN QoS. The range is from 0 to 6. vman-dual-qos number Enter the keyword vman-dual-qos and then the number of FP blocks for VMAN dual QoS. The range is from 0 to 4. Ipv4pbr number Enter the keyword ipv4pbr and then the number of FP blocks for ipv4pbr ACL. The range is from 0 to 8. Openflow number Enter the keyword openflow and then the number of FP blocks for open flow (multiples of 4).
PAGE 482
Usage Information Version 9.4. (0.0) Added support for PBR and VRF. Version 9.2(0.2) Added support for fcoe. Version 9.1. (0.0) Added support for OpenFlow. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.10.2 Clarified block information for the S4810. Version 8.3.10.0 Introduced on the S4810. Version 8.3.1.0 Added the keywords ecfmacl, vman-qos, and vman-dualqos. Version 8.2.1.0 Introduced on the S-Series. Version 7.8.1.
PAGE 483
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810.
PAGE 484
NOTE: An ACL itself may still require more that a single FP entry, regardless of the number of interfaces. For more information, refer to the “IP Access Control Lists”, “Prefix Lists”, and “Route-map” sections in the Dell Networking OS Configuration Guide. show cam-acl Display the details of the CAM profiles on the chassis and all line cards. Z9000 Syntax show cam-acl Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 485
L2Acl Ipv4Acl Ipv6Acl Ipv4Qos L2Qos L2PT IpMacAcl VmanQos VmanDualQos EcfmAcl FcoeAcl iscsiOptAcl ipv4pbr vrfv4Acl Openflow fedgovacl : : : : : : : : : : : : : : : : 1 block = 128 entries 6 4 0 2 1 0 0 0 0 0 0 0 0 0 0 0 -- Stack unit 7 -Current Settings(in block sizes) 1 block = 128 entries L2Acl : 6 Ipv4Acl : 4 Ipv6Acl : 0 Ipv4Qos : 2 L2Qos : 1 L2PT : 0 IpMacAcl : 0 VmanQos : 0 VmanDualQos : 0 EcfmAcl : 0 FcoeAcl : 0 iscsiOptAcl : 0 ipv4pbr : 0 vrfv4Acl : 0 Openflow : 0 fedgovacl : 0 Dell# Example (NonD
PAGE 486
IpMacAcl : VmanQos : VmanDualQos: Ipv4pbr : 0 0 0 0 Dell# test cam-usage Verify that enough CAM space is available for the IPv6 ACLs you have created. Z9000 Syntax Parameters test cam-usage service-policy input input policy name linecard {number | all} policy-map name Enter the name of the policy-map to verify. Maximum is 32 characters. number Enter all to get information for all the linecards/stack-units or enter the linecard/ stack-unit number to get information for a specific card.
PAGE 487
The following describes the test cam-usage command shown in the following example. Term Explanation Stack-Unit Lists the stack unit or units that are checked. Entering all shows the status for all stacks. Portpipe Lists the portpipe (port-set) or port pipes (port-sets) that are checked. Entering all shows the status for linecards and port-pipes in the chassis. CAM Partition Shows the CAM profile of the CAM. Available CAM Identifies the amount of CAM space remaining for that profile.
PAGE 488
Example (SSeries) Term Explanation Estimated CAM per Port Estimates the amount of CAM space the listed policy will require. Status Indicates whether or not the policy will be allowed in the CAM.
PAGE 489
Control Plane Policing (CoPP) 11 The CoPP commands are supported on the Dell Networking Z9000 platform. control-plane-cpuqos To manage control-plane traffic, enter control-plane mode and configure the switch. Z9000 Syntax control-plane-cpuqos Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 490
Defaults None Command Modes CONFIGURATION Command History Usage Information Version 9.4(0.0) Introduced on the S–Series and Z9000. Use this command to add the IPv4 catch-all route (0.0.0.0/0) in the LPM route forwarding table if it was deleted using the no ip unknown-unicast command previously. This will be the default configuration after reload. ipv6 unknown-unicast Disable soft forwarding of unknown IPv6 destination packets.
PAGE 491
Command Modes CONTROL-PLANE-CPUQOS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.8.0 Introduced on the S4810.
PAGE 492
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.8.0 Introduced on the S4810. This command applies the service-policy based on the type of protocol defined in the ACL rules. Create ACL and QoS policies prior to enabling this command. For CoPP, use the keyword cpu-qos when creating qos-policy-input. Related Commands ip access-list extended — creates an extended IP ACL.
PAGE 493
Version 8.3.8.0 Usage Information Introduced on the S4810. This command applies the service-policy based on the type of protocol defined in the ACL rules. Create ACL and QoS policies prior to enabling this command. Example Dell#show cpu-queue rate cp for 8 queue platform Service-Queue Rate (PPS) -------------- ----------Q0 1300 Q1 300 Q2 300 Q3 300 Q4 2000 Q5 400 Q6 400 Q7 1100 Dell# show ip protocol-queue-mapping Display the queue mapping for each configured protocol.
PAGE 494
100 UDP (DHCP) UDP (DHCP-R) TCP (FTP) ICMP IGMP TCP (MSDP) UDP (NTP) OSPF PIM UDP (RIP) TCP (SSH) TCP (TELNET) VRRP Dell# 67/68 67 any any any any/639 any any any any any any any 68/67 67 21 any any 639/any 123 any any 520 22 23 any _ _ _ _ _ _ _ _ _ _ _ _ _ Q6/Q5 Q6 Q6 Q6 Q7 Q6 Q6 Q7 Q7 Q7 Q6 Q6 Q7 CP CP CP CP CP CP CP CP CP CP CP CP CP _ _ _ _ _ _ _ _ _ _ _ _ _ show ipv6 protocol-queue-mapping Display the queue mapping for each configured IPv6 protocol.
PAGE 495
show mac protocol-queue-mapping Display the queue mapping for the MAC protocols. Z9000 Syntax show mac protocol-queue-mapping Defaults Not configured. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 496
PAGE 497
Debugging and Diagnostics 12 The basic debugging and diagnostic commands are supported by the Dell Networking Operating System (OS) on the Z-Series platform. This chapter contains the following sections: • Offline Diagnostic Commands • Buffer Tuning Commands • Hardware Commands Offline Diagnostic Commands The offline diagnostics test suite is useful for isolating faults and debugging hardware. While tests are running, Dell Networking OS results are saved as a text file (TestReport-SU-X.
PAGE 498
and perform essential path verifications. In addition, they verify the identification registers of the components on the board. level1 Enter the keyword Level1 to run Level 1 diagnostics. Level 1 diagnostics is a smaller set of diagnostic tests with support for automatic partitioning. They perform status/self test for all the components on the board and test their registers for appropriate values.
PAGE 499
Version 7.7.1.0 Introduced on the S-Series. offline stack-unit Place a stack unit in the offline state. Z9000 Syntax Parameters offline stack-unit number number Enter the stack-unit id. Z9000 - 0 to 7. Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 500
online stack-unit Place a stack unit in the online state. Z9000 Syntax Parameters online stack-unit number number Enter the stack-unit number. The Z9000 range is from 0 to 7. Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.
PAGE 501
buffer-profile (Configuration) Create a buffer profile that can be applied to an interface. Z9000 Syntax Parameters buffer-profile {fp | csf] profile-name {global {1Q | | 4q} fp Enter the keyword fp to create a buffer profile for the Field Processor. csf Enter the keyword csf to create a buffer profile for the Switch Fabric Processor. profile-name Create a name for the buffer profile, global Apply one of two pre-defined buffer profiles to all of the port-pipes in the system.
PAGE 502
If the default buffer-profile is active, Dell Networking OS displays an error message instructing you to remove the default configuration using the no bufferprofile global command. Reload the system for the global buffer-profile to take effect. Hardware Commands These commands display information from a hardware sub-component or ASIC. clear hardware stack-unit Clear statistics from selected hardware components.
PAGE 503
The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.0 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. show hardware stack-unit — displays the data plane or management plane input and output statistics of the designated component of the designated stack member.
PAGE 504
Version 7.8.1.0 Related Commands Introduced on the S-Series. show hardware stack-unit — displays the data plane or management plane input and output statistics of the designated component of the designated stack member. hardware watchdog To trigger a reboot and restart the system, set the watchdog timer. Z9000 Syntax hardware watchdog stack-unit {<0-5> | all} Defaults Enabled. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 505
port-set 0–0 Enter the keywords port-set with a port-pipe number. The range is from 0 or 3 for the Z9000.. Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 506
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.0 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. show hardware stack-unit Display the data plane or management plane input and output statistics of the designated component of the designated stack member.
PAGE 507
cpu management statistics Enter the keywords cpu management statistics to display the counters of the management port. cpu satainterface statistics Enter the keywords cpu sata-interface statistics to display the sata interface error counter statistics. drops [unit unit-number [port portnumber | no]] Enter the keyword drops to display internal drops on the selected stack member. Enter the drops keyword to display internal drops on the selected stack member.
PAGE 508
Version 8.3.11.4 Added user port information. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Introduced on the S-Series.
PAGE 509
Example (Drops Unit, Port) Dell#show hardware stack-unit 0 drops unit 1 port 27 --- Ingress Drops --Ingress Drops : 0 IBP CBP Full Drops : 0 PortSTPnotFwd Drops : 0 IPv4 L3 Discards : 0 Policy Discards : 0 Packets dropped by FP : 0 (L2+L3) Drops : 0 Port bitmap zero Drops : 0 Rx VLAN Drops : 0 --- Ingress MAC counters--Ingress FCSDrops : 0 Ingress MTUExceeds : 0 --- MMU Drops --HOL DROPS : 0 TxPurge CellErr : 0 Aged Drops : 0 --- Egress MAC counters--Egress FCS Drops : 0 --- Egress FORWARD PROCESSOR Drops
PAGE 510
hg3 down 10G FD 0 Dell# Example (Register) 510 SW No Forward None F XGMII 16360 Dell#show hardware stack-unit 0 unit 1 register 0x0068003c AGINGCTRMEMDEBUG.mmu0 = 0x00000000 0x0068003d AGINGEXPMEMDEBUG.mmu0 = 0x00000000 0x00680017 ASFCONFIG.mmu0 = 0x0000000e 0x0060004c ASFPORTSPEED.ge0 = 0x00000000 0x0060104c ASFPORTSPEED.ge1 = 0x00000000 0x0060204c ASFPORTSPEED.ge2 = 0x00000000 0x0060304c ASFPORTSPEED.ge3 = 0x00000000 0x0060404c ASFPORTSPEED.ge4 = 0x00000000 0x0060504c ASFPORTSPEED.
PAGE 511
0x0e719102 BCAST_BLOCK_MASK.hg1 = 0x00000000 0x0e71a102 BCAST_BLOCK_MASK.hg2 = 0x00000000 0x0e71b102 BCAST_BLOCK_MASK.hg3 = 0x00000000 0x0e71c102 BCAST_BLOCK_MASK.cpu0 = 0x00000000 0x0b700001 BCAST_STORM_CONTROL.ge0 = 0x00000000 0x0b701001 BCAST_STORM_CONTROL.ge1 = 0x00000000 0x0b702001 BCAST_STORM_CONTROL.ge2 = 0x00000000 0x0b703001 BCAST_STORM_CONTROL.ge3 = 0x00000000 0x0b704001 BCAST_STORM_CONTROL.ge4 = 0x00000000 0x0b705001 BCAST_STORM_CONTROL.ge5 = 0x00000000 0x0b706001 BCAST_STORM_CONTROL.
PAGE 512
The linkStatus of Front End Port 20 is FALSE The linkStatus of Front End Port 21 is FALSE The linkStatus of Front End Port 22 is FALSE The linkStatus of Front End Port 23 is TRUE The linkStatus of Hg Port 24 is TRUE The linkStatus of Hg Port 25 is TRUE The linkStatus of Hg Port 26 is FALSE The linkStatus of Hg Port 27 is FALSE !------------------ output truncated ---------------! Example (Total-Buffer) Dell(conf)#show hardware stack-unit 0 buffer total-buffer Example (Buffer-Info) Dell(conf)#sh hardware
PAGE 513
stack-unit id Enter the keywords stack-unit to select a stack member ID. The unit ID range for Z9000 is 0. port-set number [counters] Enter the keywords port-set with a port-pipe number. The range is 0 to 1 for the Z9000. (OPTIONAL) Enter the keyword counters to display hit counters for the selected ACL or QoS option. Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 514
1 25 Dell# Example L2BCASTPackets 0 param1=0(0x00)}, action={act=CosQCpuNew, param0=7(0x07), param1=0(0x00)}, action={act=CopyToCpu, param0=0(0x00), param1=0(0x00)}, action={act=UpdateCounter, param0=1(0x01), param1=0(0x00)}, meter=NULL, counter={idx=1, mode=0x01, entries=1} ############## FP Entry for redirecting LACP traffic to CPU Port ############ EID 2045: gid=1, slice=15, slice_idx=0x02, prio=0x7fd, flags=0x82, Installed tcam: color_indep=0, higig=0, higig_mask=0, KEY=0x00000000 00000000 00000000 0
PAGE 515
action={act=UpdateCounter, param0=1(0x01), param1=0(0x00)}, !--------- output truncated -----------------! Debugging and Diagnostics 515
PAGE 516
PAGE 517
Dynamic Host Configuration Protocol (DHCP) 13 Dynamic host configuration protocol (DHCP) is an application layer protocol that dynamically assigns IP addresses and other configuration parameters to network end-stations (hosts) based on the configuration policies the network administrators determine. The Dell Networking operating system supports the basic DHCP commands on the Z9000 platform.
PAGE 518
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced on the C-Series and S-Series.
PAGE 519
default-router Assign a default gateway to clients based on the address pool. Z9000 Syntax Parameters default-router address [address2...address8] address Enter a list of routers that may be the default gateway for clients on the subnet. You may specify up to eight routers. List them in order of preference. Defaults none Command Modes DHCP Command History This guide is platform-specific.
PAGE 520
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced on the C-Series and S-Series. dns-server Assign a DNS server to clients based on address pool. Z9000 Syntax Parameters dns-server address [address2...address8] address Enter a list of DNS servers that may service clients on the subnet. You may list up to eight servers, in order of preference.
PAGE 521
Defaults none Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.
PAGE 522
Version 8.2.1.0 Introduced on the C-Series and S-Series. hardware-address For manual configurations, specify the client hardware address. Z9000 Syntax Parameters hardware-address address address Enter the hardware address of the client. Defaults none Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 523
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced on the C-Series and S-Series. ip helper-address Configures the destination broadcast address or the host address for DHCP server requests.
PAGE 524
lease Specify a lease time for the addresses in a pool. Z9000 Syntax Parameters lease {days [hours] [minutes] | infinite} days Enter the number of days of the lease. The range is from 0 to 31. hours Enter the number of hours of the lease. The range is from 0 to 23. minutes Enter the number of minutes of the lease. The range is from 0 to 59. infinite Specify that the lease never expires. Defaults 24 hours Command Modes DHCP Command History This guide is platform-specific.
PAGE 525
Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced on the C-Series and S-Series.
PAGE 526
Version 8.2.1.0 Introduced on the C-Series and S-Series. network Specify the range of addresses in an address pool. Z9000 Syntax Parameters network network /prefix-length network/ prefix-length Specify a range of addresses. Prefix-length range is from 17 to 31. Defaults none Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 527
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced on the C-Series and S-Series. show ip dhcp binding Display the DHCP binding table. Z9000 Syntax show ip dhcp binding Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 528
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.
PAGE 529
show ip dhcp server Display the DHCP server statistics. Z9000 Syntax show ip dhcp server statistics Defaults none Command Modes EXEC Privilege Command History Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced on the C-Series and S-Series. clear host Removes one or all dynamically learned host table entries for a specific VRF.
PAGE 530
Version 9.4. (0.0) Introduced on the S-Series and Z-Series. Usage Information Use this command to delete one or all dynamically learned host table entries corresponding to a specific VRF. Example Dell#clear host vrf jay dell Dell#clear host vrf jay * ip domain-list Adds a domain name to the DNS list. This domain name is appended to incomplete host names in DNS requests corresponding to a specific VRF.
PAGE 531
ip domain-name Configures the default domain corresponding to a specific VRF. This domain is appended to the in complete DNS requests corresponding to the specified VRF. Z9000 Syntax ip domain-name [vrf vrf-name] name To undo the domain name configuration corresponding to a specific VRF, use the no ip domain-name [vrf vrf-name] name command. Parameters vrf vrf-name (Optional) Enter the key word vrf and then the name of the VRF to configure the domain corresponding to that VRF.
PAGE 532
Parameters vrf vrf-name (Optional) Enter the key word vrf and then the name of the VRF to configure the name server to IP address mapping for that VRF. name Enter the name od the host to be associated with an IP address. ip-address Enter the IP address of the name server in dotted decimal format. Defaults None Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 533
ip-address [ipaddress2] [ipaddress3] [ipaddress4] [ipaddress5] [ipaddress6] Enter the IP address of the name server in dotted decimal format. NOTE: Use the additional ip-address parameters (ipaddress2 to ip-address6) in a sequential order to specify up to a maximum of six IP addresses per VRF. Defaults None Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 534
Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Introduced on the E-Series. Version 8.2.1.0 Introduced on the C-Series and S-Series. arp inspection-trust — specifies a port as trusted so that ARP frames are not validated against the binding table.
PAGE 535
clear ip dhcp snooping Clear the DHCP binding table. Z9000 Syntax clear ip dhcp snooping binding Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T.
PAGE 536
The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.2) Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Introduced on the E-Series. Version 7.8.1.0 Introduced on the C-Series and S-Series. ip dhcp snooping Enable DHCP snooping globally. Z9000 Syntax [no] ip dhcp snooping Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 537
ip dhcp snooping binding Create a static entry in the DHCP binding table. Z-Series Syntax Parameters [no] ip dhcp snooping binding mac address vlan-id vlan-id ip ip-address interface type slot/port lease number mac address Enter the keyword mac then the MAC address of the host to which the server is leasing the IP address. vlan-id vlan-id Enter the keywords vlan-id then the VLAN to which the host belongs. The range is from 2 to 4094.
PAGE 538
Related Commands Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Introduced on the E-Series. Version 7.8.1.0 Introduced on the C-Series and S-Series. show ip dhcp snooping — displays the contents of the DHCP binding table. ip dhcp snooping database Delay writing the binding table for a specified time. Z9000 Syntax Parameters ip dhcp snooping database write-delay minutes minutes The range is from 5 to 21600.
PAGE 539
Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.
PAGE 540
ip dhcp source-address-validation Enable the IP Source Guard. Z9000 Syntax Parameters [no] ip dhcp source-address-validation [ipmac] ipmac Enable IP+MAC Source Address Validation. Defaults Disabled Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.
PAGE 541
Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.1.0 Introduced on the E-Series. Version 7.8.1.0 Introduced on the C-Series and S-Series.
PAGE 542
Example Version 9.4. (0.0) Added support for VRF. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Introduced on the E-Series. Version 7.8.1.0 Introduced on C-Series and S-Series. Dell(conf)#ip dhcp relay information-option vpn ip dhcp relay information-agent remote-id Manually re-set the remote-id for Option 82.
PAGE 543
ip dhcp snooping verify mac-address Validate a DHCP packet’s source hardware address against the client hardware address field (CHADDR) in the payload. Z9000 Syntax [no] ip dhcp snooping verify mac-address Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 544
The following is a list of the Dell Networking OS version history for this command. 544 Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Introduced on the E-Series. Version 7.8.1.0 Introduced on the C-Series and S-Series.
PAGE 545
Equal Cost Multi-Path (ECMP) 14 Equal cost multi-path (ECMP) is supported on the Dell Networking Z9000 platform. ecmp-group Provides a mechanism to monitor traffic distribution on an ECMP link bundle. A system log is generated when the standard deviation of traffic distribution on a member link exceeds a defined threshold. Z9000 Syntax ecmp-group {ecmp-group-id interface interface | link-bundlemonitor} To remove the selected interface, use the ecmp-group no interface command.
PAGE 546
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.10.0 Introduced on the S4810. Using CONFIGURATION mode, create an ECMP group ID. You can then assign interfaces to the ECMP group using CONFIGURATION ECMP-GROUP mode. You can also enable on the port-channel configuration using the CONFIGURATION ECMP-GROUP command mode.
PAGE 547
ecmp crc16 | crc16cc | crc32MSB | crc32LSB | crcupper | dest-ip | lsb | xor1 | xor2 | xor4 | xor8 | xor16 hg {crc16 | crc16cc | crc32MSB | crc32LSB | xor1 | xor2 | xor4 | xor8 | xor16} stack-unit stack-unitnumber | portset port-pipe TeraScale and ExaScale Only: Enter the keyword ecmp then one of the following options: • crc16: Use CRC16_BISYNC — 16 bit CRC16-bisync polynomial (default) • crc16cc: Use CRC16_CCITT — 16 bit CRC16 using CRC16-CCITT polynomial • crc32MSB: Use CRC32_UPPER — MSB 16 bits of
PAGE 548
Enter the keywords port-set port-pipe then the port pipe number. The range is from 0 to 5. hg-seed seedvalue stackunit Z-Series only: Enter the keywords hg-seed then the hash algorithm seed value. The range is from 0 to 2147483646. Enter the keywords stack-unit then the stack unit number. The range is from 0 to 7. Enter the keywords port-set then the stack-unit port-pipe number. The range is from 0 to 5. lag hash algorithm Z-Series only: Enter the keywords hg-seed . The range is from 0 to 47.
PAGE 549
Version 7.7.1.1 Usage Information Added the nh-ecmp option. To ensure that CRC is not used for LAG, set the default hash-algorithm method on ExaScale systems. For example,hash-algorithm ecmp xor lag checksum nh-ecmp checksum. The hash value calculated with the hash-algorithm command is unique to the entire chassis. The hash algorithm command with the stack—unit option changes the hash for a particular stack—unit by applying the mask specified in the IPSA and IPDA fields.
PAGE 550
hash-algorithm ecmp Change the hash algorithm used to distribute traffic flows across an ECMP (equal-cost multipath routing) group. Z9000 Term heading Description heading Syntax hash-algorithm ecmp {crc-upper} | {dest-ip} | {lsb} To return to the default hash algorithm, use the no hash-algorithm ecmp command. Parameters Defaults crc-upper Uses the upper 32 bits of the key for the hash computation. The default is crc-lower. dest-ip Uses the destination IP for ECMP hashing. The default is enabled.
PAGE 551
Term heading Description heading various test scenarios, but if the default algorithm does not provide satisfactory distribution of traffic, use this command to designate another algorithm. When a member leaves or is added to the ECMP group, the hash algorithm is recalculated to balance traffic across the members. hash-algorithm hg To distribute traffic flows across different internal HiGig links, change the hash algorithm.
PAGE 552
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 8.3.11.4 Introduced on the Z9000. hash-algorithm hg-seed Select the seed value used in HiGig hashing.
PAGE 553
Parameters seed value Enter the keyword seed then the seed value. The range is from 0 to 4095. linecard slot Enter the keyword linecard then the linecard slot number. port-set number Enter the keyword port-set then the linecard port-pipe number. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 554
ip ecmp-group Enable and specify the maximum number of ecmp that the L3 CAM hold for a route, By default, when maximum paths are not configured, the CAM can hold a maximum of 16 ecmp per route. Z9000 Syntax ip ecmp-group {maximum-paths | {number} {path-fallback} To negate a command, use the no ip ecmp-group maximum-paths {number} command. Parameters maximumpaths Specify the maximum number of ECMP for a route. The range is 2 to 64. path-fallback Use the keywords path-fallback to enable this feature.
PAGE 555
Parameters percent Indicate the threshold value when traffic distribution starts being monitored on an ECMP link bundle. The range is from 1 to 90%. The default is 60%. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.
PAGE 556
Version 8.3.10.0 Introduced on the S4810. show config Display the ECMP configuration. Z9000 Syntax show config Command Modes CONFIGURATION-ECMP-GROUP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.
PAGE 557
Example Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810.
PAGE 558
PAGE 559
FIPS Cryptography 15 To configure federal information processing standards (FIPS) cryptography, use the following commands on the Z-Series platform. fips mode enable Enable the FIPS cryptography mode on the platform. Z-Series Syntax [no] fips mode enable To disable the FIPS cryptography mode, use the no fips mode enable command.
PAGE 560
show fips status Displays the status of the FIPS mode. Z-Series Syntax show fips status Defaults None Command Modes EXEC Example Dell #show fips status FIPS Mode: Enabled Dell# Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.1(0.0) Introduced on the Z9000. Version 8.3.19.
PAGE 561
Example Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on S4810. Dell #show ip ssh SSH server SSH server version Password Authentication Hostbased Authentication RSA Authentication Vty Encryption 1 3des-cbc 2 3des-cbc : enabled. : v1 and v2. : enabled. : disabled. : disabled. HMAC Remote IP hmac-md5 10.1.20.48 hmac-md5 10.1.20.48 With FIPS Mode enabled: Dell #show ip ssh SSH server : enabled. SSH server version : v2. Password Authentication : enabled.
PAGE 562
-c encryption cipher Enter the following encryption cipher to use. (For v2 clients only.) Without the FIPS mode enabled: • 3des-cbc: Force ssh to use 3des-cbc encryption cipher. With the FIPS mode enabled: • aes128–cbc: Force ssh to use the aes128–cbc encryption cipher. • aes256–cbc: Force ssh to use the aes256–cbc encryption cipher. -l username (OPTIONAL) Enter the keyword —l then the user name used in this SSH session. The default is the user name of the user associated with the terminal.
PAGE 563
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Usage Information Version 9.1(0.0) Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. ip ssh server Configure an SSH server.
PAGE 564
aes256-cbc Force ssh to use aes256-cbc encryption cipher Dell#ssh 10.11.8.
PAGE 565
16 Force10 Resilient Ring Protocol (FRRP) Force10 resilient ring protocol (FRRP) is supported on Dell Networking Z9000 platform. FRRP is a proprietary protocol for that offers fast convergence in a Layer 2 network without having to run the spanning tree protocol (STP). The resilient ring protocol is an efficient protocol that transmits a highspeed token across a ring to verify the link status.
PAGE 566
Usage Information Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced on the C-Series. Version 7.5.1.0 Introduced. Executing this command without the optional ring-id command clears the statistics counters on all the available rings. Dell Networking OS requires a command line confirmation before the command executes.
PAGE 567
detail Enter the keyword detail to display detailed debug information related to the entire ring protocol packets. ring-id (Optional) Enter the ring identification number. The range is from 1 to 255. count number Enter the keyword count then the number of debug outputs. The range is from 1 to 65534. Defaults Disabled. Command Modes CONFIGURATION (conf-frrp) Command History This guide is platform-specific.
PAGE 568
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced.
PAGE 569
interface Configure the primary, secondary, and control-vlan interfaces. Z9000 Syntax interface {primary interface secondary interface control-vlan vlan-id} To return to the default, use the no interface {primary interface secondary interface control-vlan vlan-id} command.
PAGE 570
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced. Usage Information This command causes the Ring Manager to take ownership of the two ports after IFM validates the configuration.
PAGE 571
Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced. mode Set the Master or Transit mode of the ring. Z9000 Syntax mode {master | transit} To reset the mode, use the no mode {master | transit} command. Parameters master Enter the keyword master to set the Ring node to Master mode. transit Enter the keywordtransit to set the Ring node to Transit mode.
PAGE 572
protocol frrp Enter the Resilient Ring Protocol and designate a ring identification. Z9000 Syntax protocol frrp {ring-id} To exit the ring protocol, use the no protocol frrp {ring-id} command. Parameters ring-id Enter the ring identification number. The range is from 1 to 255. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 573
summary (OPTIONAL) Enter the keyword summary to view just a summarized version of the Ring configuration. Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 574
Primary : GigabitEthernet 0/16 State: Forwarding Secondary: Port-channel 100 State: Blocking Control Vlan: 1 Ring protocol Timers: Hello-Interval 50 msec Dead-Interval 150 msec Ring Master's MAC Address is 00:01:e8:13:a3:19 Topology Change Statistics: Tx:110 Rx:45 Hello Statistics: Tx:13028 Rx:12348 Number of state Changes: 34 Member Vlans: 1000-1009 Dell# Example (2 Summary) Dell#show frrp 2 summary Related Commands protocol frrp — enters the resilient ring protocol and designate a ring identification.
PAGE 575
Command Modes CONFIGURATION (conf-frrp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.
PAGE 576
PAGE 577
GARP VLAN Registration (GVRP) 17 The Dell Networking operating system supports the basic GVRP commands on the Z9000 platform. The generic attribute registration protocol (GARP) mechanism allows the configuration of a GARP participant to propagate through a network quickly. A GARP participant registers or de-registers its attributes with other participants by making or withdrawing declarations of attributes.
PAGE 578
• VLANs created dynamically with GVRP exist only as long as a GVRP-enabled device is sending updates. If the devices no longer send updates, or GVRP is disabled, or the system is rebooted, all dynamic VLANs are removed. • GVRP manages the active topology, not non-topological data such as VLAN protocols. If a local bridge must classify and analyze packets by VLAN protocols, manually configure protocol-based VLANs, and simply rely on GVRP for VLAN updates.
PAGE 579
Related Commands show gvrp statistics — displays the GVRP statistics. debug gvrp Enable debugging on GVRP. Z9000 Syntax debug gvrp {config | events | pdu} To disable debugging, use the no debug gvrp {config | events | pdu} command. Parameters config Enter the keyword config to enable debugging on the GVRP configuration. event Enter the keyword event to enable debugging on the JOIN/ LEAVE events.
PAGE 580
disable Globally disable GVRP. Z9000 Syntax disable To re-enable GVRP, use the no disable command. Defaults Enabled. Command Modes CONFIGURATION-GVRP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 581
NOTE: Designate the milliseconds in multiples of 100. leave Enter the keyword leave then the number of milliseconds to configure the leave time. The range is from 100 to 2147483647 milliseconds. The default is 600 milliseconds. NOTE: Designate the milliseconds in multiples of 100. leave-all Enter the keywords leave-all then the number of milliseconds to configure the leave-all time. The range is from 100 to 2147483647 milliseconds. The default is 1000 milliseconds.
PAGE 582
gvrp enable Enable GVRP on physical interfaces and LAGs. Z9000 Syntax gvrp enable To disable GVRP on the interface, use the no gvrp enable command. Defaults Disabled. Command Modes CONFIGURATION-INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.
PAGE 583
Defaults normal Command Modes CONFIGURATION-INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810.
PAGE 584
The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on C-Series, E-Series, and S-Series disable — globally disables GVRP. show config Display the global GVRP configuration.
PAGE 585
show garp timers Display the GARP timer settings for sending GARP messages. Z9000 Syntax show garp timers Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T.
PAGE 586
interface (OPTIONAL) Enter the following keywords and slot/port or number information: • For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
PAGE 587
show gvrp statistics Display the GVRP configuration statistics. Z9000 Syntax Parameters show gvrp statistics {interface interface | summary} interface interface summary (OPTIONAL) Enter the keyword interface then one of the interface keywords and slot/ port or number information: • For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 588
• Example An entry for a new GVRP VLAN could not be created in the GVRP database.
PAGE 589
18 GRUB GRUB commands are supported on the Z9000 platform only. To access this mode, press the ESC key when the following line appears on the console during a system boot: Press ESC key to stop autoreboot... Select Force10 Boot on the screen and press C. You enter the GRUB mode immediately, as indicated by the grub> prompt. NOTE: This chapter describes only a few commands available in GRUB. NOTE: You cannot use the Tab key to complete commands in this mode. clear Clears the grub screen.
PAGE 590
Command Modes Command History Example grub Version 8.3.11.1 Introduced on the Z9000. grub>list_env serverip=10.11.200.241 ipaddr=10.11.196.141 netmask=255.255.0.0 gatewayip=10.11.196.
PAGE 591
save_env Saves the environment variables set using the set command. Z9000 Syntax Parameters Command Modes Command History save_env environment variable environment variable Enter the environment variable to be saved. grub Version 8.3.11.1 Introduced on the Z9000. Usage Information The environment variables are listed under the list_env command. You must save the environment variables before rebooting. The save_env command must be used for each variable set using the set command.
PAGE 592
secondary_boo t Set the secondary boot parameter. The location must be flash0, flash1 or any valid tftp location. The secondary boot parameter must be in the following syntax: set secondary_boot=’f10boot flash0 | flash1 | tftp://ip-addr/file’ default_boot Set the default boot parameter. The location must be flash0, flash1 or any valid tftp location.
PAGE 593
19 ICMP Message Types This chapter lists and describes the possible ICMP message type resulting from a ping. The first three columns list the possible symbol or type/code. For example, you would receive a ! or 03 as an echo reply from your ping. ICMP Messages and Their Definitions.\ Symbol Type Code . Query Error Timeout (no reply) ! 0 U 3 C Description 4 5 ICMP Message Types 3 echo reply . destination unreachable: 0 network unreachable . 1 host unreachable .
PAGE 594
Symbol & Type Code Description 0 redirect for network . 1 redirect for host . 2 redirect for type-of-service and network . 3 redirect for type-of-service and host . 8 0 echo request . 9 0 router advertisement . 10 0 router solicitation . 11 Error time exceeded: 0 time-to-live equals 0 during transit . 1 time-to-live equals 0 during reassembly . 12 594 Query parameter problem: 1 IP header bad (catchall error) . 2 required option missing .
PAGE 595
Internet Group Management Protocol (IGMP) 20 The IGMP commands are supported by the Dell Networking operating software on the Z9000 platform. This chapter contains the following sections: • IGMP Commands • IGMP Snooping Commands IGMP Commands Dell Networking OS supports IGMPv1/v2/v3 and is compliant with RFC-3376.
PAGE 596
• For a VLAN interface, enter the keyword vlan then the slot/port information. The range is from 1 to 4094. • For a 1-Gigabit Ethernet interface, enter the keyword gigabitethernet followed by the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword tengigabitethernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. Command Modes EXEC Command History This guide is platform-specific.
PAGE 597
interface interface Enter the following keywords and slot/port or number information: • For a 1-Gigabit Ethernet interface, enter the keyword gigabitethernet followed by the slot/port information. • For a Port Channel interface, enter the keyword portchannel then a number. The range is from 1 to 128. • For a 10–Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 598
Parameters access-list Enter the name of the extended ACL (16 characters maximum). Defaults Not configured Command Modes INTERFACE (conf-if-interface-slot/port) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 599
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the C-Series and S-Series. Version 7.6.1.0 Introduced on the E-Series. ip igmp immediate-leave Enable IGMP immediate leave. Z9000 Syntax ip igmp immediate-leave [group-list prefix-list-name] To disable ip igmp immediate leave, use the no ip igmp immediateleave command.
PAGE 600
Usage Information Querier normally sends some group-specific queries when a leave message is received for a group prior to deleting a group from the membership database. There may be situations when you require immediate deletion of a group from the membership database. This command provides a way to achieve the immediate deletion. In addition, this command provides a way to enable immediate-leave processing for specified groups.
PAGE 601
ip igmp querier-timeout Change the interval that must pass before a multicast router decides that there is no longer another multicast router that should be the querier. Syntax ip igmp querier-timeout seconds To return to the default value, use the no ip igmp querier-timeout command. Parameters seconds Enter the number of seconds the router must wait to become the new querier. The range is from 60 to 300. The default is 125 seconds.
PAGE 602
ip igmp query-interval Change the transmission frequency of IGMP general queries the Querier sends. Z9000 Syntax ip igmp query-interval seconds To return to the default values, use the no ip igmp query-interval command. Parameters seconds Enter the number of seconds between queries sent out. The range is from 1 to 18000. The default is 60 seconds. Defaults 60 seconds Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 603
ip igmp query-max-resp-time Set the maximum query response time advertised in general queries. Z9000 Syntax ip igmp query-max-resp-time seconds To return to the default values, use the no ip igmp query-max-resp-time command. Parameters seconds Enter the number of seconds for the maximum response time. The range is from 1 to 25. The default is 10 seconds. Defaults 10 seconds Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 604
ip igmp ssm-map To translate (*,G) memberships to (S,G) memberships, use a statically configured list. Z9000 Syntax ip igmp ssm-map std-access-list source-address Undo this configuration, that is, remove SSM map (S,G) states and replace them with (*,G) state, use the ip igmp ssm-map std-access-list sourceaddress command. Parameters std-access-list Specify the standard IP access list that contains the mapping rules for multicast groups.
PAGE 605
ip igmp static-group Configure an IGMP static group. Z9000 Syntax ip igmp static-group {group address [exclude [source address]] | [include {source address}]} To delete a static address, use the no ip igmp static-group {group address [exclude [source address]] | [include {source address}]} command. Parameters group address Enter the group address in dotted decimal format (A.B.C.D). exclude source address (OPTIONAL) Enter the keyword exclude then the source address, in dotted decimal format (A.B.C.
PAGE 606
implicitly assumes all sources are included. If you do not specify either include or exclude, Dell Networking OS implicitly assumes a IGMPv2 static join. Command Limitations Related Commands • Only one mode (include or exclude) is permitted per multicast group per interface. To configure another mode, all sources belonging to the original mode must be unconfigured.
PAGE 607
Version 7.5.1.0 Introduced on the E-Series. show ip igmp groups View the IGMP groups. Z9000 Syntax Parameters show ip igmp groups [group-address [detail] | detail | interface [group-address [detail]]] group-address (OPTIONAL) Enter the group address in dotted decimal format to view information on that group only. interface (OPTIONAL) Enter the interface type and slot/port information: detail • For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128.
PAGE 608
Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series and C-Series. Version 7.5.1.0 Expanded to support the detail option. E-Series legacy command. Usage Information This command displays the IGMP database, including configured entries for either all groups on all interfaces, all groups on specific interfaces, or specific groups on specific interfaces.
PAGE 609
Group Address Interface Mode 225.0.0.0 Vlan 100 IGMPv2 Member Ports: Po 2* 225.0.0.1 Vlan 100 IGMPv2 Member Ports: Po 2* 225.0.0.2 Vlan 100 IGMPv2 Member Ports: Po 2* 225.0.0.3 Vlan 100 IGMPv2 Member Ports: Po 2* 225.0.0.4 Vlan 100 IGMPv2 Member Ports: Po 2* Uptime Expires Last Reporter 00:00:05 00:02:04 3.0.0.51 00:00:05 00:02:04 3.0.0.51 00:00:05 00:02:04 3.0.0.51 00:00:05 00:02:04 3.0.0.51 00:00:05 00:02:04 3.0.0.51 show ip igmp interface View information on the interfaces participating in IGMP.
PAGE 610
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series legacy command. Usage Information IGMP commands accept only non-VLAN interfaces — specifying VLAN does not yield results.
PAGE 611
Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the C-Series and S-Series. Version 7.7.1.0 Introduced on the E-Series. ip igmp ssm-map — uses a statically configured list to translate (*,G) memberships to (S,G) memberships.
PAGE 612
If the IP SA in the incoming IGMP general query frame is lower than the IP address of the VLAN interface, the switch disables its IGMP snooping Querier functionality. If the IP SA of the incoming IGMP general query is higher than the VLAN IP address, the switch continues to work as an IGMP snooping Querier. ip igmp snooping enable Enable IGMP snooping on all or a single VLAN. This command is the master on/off switch to enable IGMP snooping.
PAGE 613
ip igmp snooping fast-leave Enable IGMP snooping fast-leave for this VLAN. Z9000 Syntax ip igmp snooping fast-leave To disable IGMP snooping fast leave, use the no igmp snooping fast-leave command. Defaults Not configured. Command Modes INTERFACE VLAN — (conf-if-vl-n) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 614
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.
PAGE 615
Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series.
PAGE 616
Command Modes INTERFACE VLAN — (conf-if-vl-n) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T.
PAGE 617
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information This command enables the IGMP switch to send General Queries periodically. This behavior is useful when there is no multicast router present in the VLAN because the multicast traffic is not routed.
PAGE 618
Usage Information If the port channel is a VLT port channel, an asterisk (*) after the port channel number (Po 100*) indicates the port channel is locally down and that a remote VLT port is up. Example Dell#show ip igmp snooping mrouter Interface Router Ports Vlan 2 Gi 13/3, Po 1 Dell# Related Commands 618 • ip igmp snooping mrouter — configures a static connection to the multicast router. • show ip igmp groups — view groups.
PAGE 619
21 Interfaces The commands in this chapter are supported by Dell Networking operating software on the Z9000 platform. This chapter contains the following sections: • Basic Interface Commands • Port Channel Commands • Time Domain Reflectometer (TDR) • UDP Broadcast Basic Interface Commands The following commands are for Physical, Loopback, and Null interfaces.
PAGE 620
• For a tunnel interface, enter the keyword tunnel. The range is from 1 to 16383. vrrp [[ipv6] vrid] (OPTIONAL) Enter the keyword vrrp to clear the counters of all VRRP groups. To clear the counters of VRRP groups on all IPv6 interfaces, enter ipv6. To clear the counters of a specified group, enter a VRID number from 1 to 255. learning-limit (OPTIONAL) Enter the keywords learning-limit to clear unknown source address (SA) drop counters when MAC learning limit is configured on the interface.
PAGE 621
clear dampening Clear the dampening counters on all the interfaces or just the specified interface. Z9000 Syntax Parameters clear dampening [interface] interface (OPTIONAL) Enter any of the following keywords and slot/ port or number to clear counters from a specified interface: • For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 622
Related Commands show interfaces dampening — displays interface dampening information. dampening — configures dampening on an interface. dampening Configure dampening on an interface. Z9000 Syntax Parameters dampening [[[[half-life] [reuse-threshold]] [suppressthreshold]] [max-suppress-time]] half-life Enter the number of seconds after which the penalty is decreased. The penalty decreases half after the half-life period expires. The range is from 1 to 30 seconds. The default is 5 seconds.
PAGE 623
Usage Information Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced on the E-Series. With each flap, Dell Networking OS penalizes the interface by assigning a penalty (1024) that decays exponentially depending on the configured half-life. After the accumulated penalty exceeds the suppress threshold value, the interface moves to the Error-Disabled state. This interface state is deemed as “down” by all static/ dynamic Layer 2 and Layer 3 protocols.
PAGE 624
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Modified for E-Series: Revised from 78 to 240 characters.
PAGE 625
Version 9.0.2.0 Introduced on the S6000. Version 8.3.11.1 Introduced on the Z9000. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Documentation modified—added Management to distinguish from duplex (10/100 Interfaces). Usage Information This command applies only to the Management interface on the route processor modules (RPMs).
PAGE 626
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.4.1.0 Introduced Usage Information This command applies to any physical interface with speed set to 10/100. Related Commands speed (for 10/100/1000 interfaces) — sets the speed on the Base-T Ethernet interface.
PAGE 627
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.
PAGE 628
• • Speeds less than 1 Gig cannot be configured when the asymmetric flow control configuration is on. The following error is returned: Can’t configure speed <1G when Asymmetric flowcontrol is on, config ignored Dell Networking OS only supports rx on tx on and rx off tx off for speeds less than 1 Gig (Symmetric). NOTE: If you use the disable rx flow control command, Dell Networking recommends rebooting the system.
PAGE 629
Related Commands on on on on off off on on off off on on on on off off on on on on off off on on show running-config — displays the flow configuration parameters (non-default values only). show interfaces — displays the negotiated flow control parameters. interface Configure a physical interface on the switch.
PAGE 630
Usage Information Version 9.4(0.0) Added the support for interfaces. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.4.1.
PAGE 631
interface group Create or delete group of VLANs with a single command. You can also use this command to apply a set of configurations on a group of interfaces. Z9000 Syntax interface group [fortyGigE slot/port { - port }| gigabitethernet slot/port { - port }| tengigabitethernet slot/ port { - port } | vlan vlanid {- vlanid } ] To delete a range of VLANs, use the following command: no interface group vlan vlanid {- vlanid} Parameters interface, interface,...
PAGE 632
Usage Information The interface group command will create all the non-existent VLANs specified in the range. On successful command execution, the CLI switches to the interface group context. The configuration commands inside the group context will be the similar to that of the existing range command. Note: For release 9.4(0.0), the group command is supported only for VLANs and physical interfaces.
PAGE 633
Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.4.1.0 Introduced Example Dell(conf)#interface loopback 1655 Dell(conf-if-lo-1655)# Related Commands interface — configures a physical interface. interface null — configures a Null interface. interface port-channel — configures a port channel. interface vlan — configures a VLAN.
PAGE 634
Usage Information You cannot delete a Management port. The Management port is enabled by default (no shutdown). To assign an IP address to the Management port, use the ip address command. If your system has two RPMs installed, use the show redundancy command to display which RPM is the Primary RPM. Example Dell(conf)#interface managementethernet 0/0 Dell(conf-if-ma-0/0)# Related Commands management route — configures a static route that points to the Management interface or a forwarding router.
PAGE 635
Usage Information You cannot delete the Null interface. The only configuration command possible in a Null interface is ip unreachables. Example Dell(conf)#interface null 0 Dell(conf-if-nu-0)# Related Commands interface — configures a physical interface. interface loopback — configures a Loopback interface. interface port-channel — configures a port channel. interface vlan — configures a VLAN. ip unreachables — enables generation of internet control message protocol (ICMP) unreachable messages.
PAGE 636
Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.5.1.
PAGE 637
Example (Multiple Ports) Dell(conf)#interface range gi 2/0 - 23, gi 2/1 - 10 Dell(conf-if-range-gi-2/0-23# Example (Overlapping Ports) Dell(conf)#interface range gi 2/1 - 11, gi 2/1 - 23 Dell(conf-if-range-gi-2/1-23# Usage Information Only VLAN and port-channel interfaces created using the interface vlan and interface port-channel commands can be used in the interface range command. Use the show running-config command to display the VLAN and port-channel interfaces.
PAGE 638
show range — shows the bulk configuration ranges. interface range macro (define) — defines a macro for an interface-range. interface range macro (define) Defines a macro for an interface range and then saves the macro in the running configuration. Z9000 Syntax Parameters define interface range macro name interface , interface , ... name Enter up to 16 characters for the macro name. interface, interface,...
PAGE 639
Example (Single Range) Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.2.1.0 Added support for 4093 VLANs on E-Series ExaScale. Prior releases supported 2094. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.
PAGE 640
The following is a list of the Dell Networking OS version history for this command. Example (Single Range) Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.2.1.
PAGE 641
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 9.1. (0.0) Introduced on the S4810; added support for OpenFlow. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. For more information about VLANs and the commands to configure them, refer to the Virtual LAN (VLAN) Commands section of the Layer 2 chapter. FTP, TFTP, and SNMP operations are not supported on a VLAN. MAC ACLs are not supported in VLANs. IP ACLs are supported.
PAGE 642
intf-type cr4 autoneg Set the interface type as CR4 with auto-negotiation enabled. Z9000 Syntax intf-type cr4 autoneg If you configure intf-type cr4 autoneg, use the no intf-type cr4 autoneg command to set the interface type as cr4 with autonegotiation disabled. Defaults Not configured Command Modes CONFIGURATION Command History Usage Information Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000.
PAGE 643
Defaults Enabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.
PAGE 644
Version 8.3.16.1 Usage Information Related Commands Introduced on the MXL 10/40GbE Switch IO Module. If you configure interface type as CR4 with auto-negotiation enabled, also configure CR4 with auto-negotiation. Many DAC cable link issues are resolved by setting the interface type as CR4. • Interfaces — configures a physical interface. • interface loopback — configures a loopback interface. • interface null — configures a null interface.
PAGE 645
The no negotiation auto command is only available if you first manually set the speed of a port to 10Mbits or 100Mbits. The negotiation auto command provides a mode option for configuring an individual port to forced-master/forced slave after you enable auto-negotiation. NOTE: The mode option is not available on non-10/100/1000 Base-T Ethernet line cards. If you do not use the mode option, the default setting is slave.
PAGE 646
User Information Both sides of the link must have auto-negotiation enabled or disabled for the link to come up. The following details the possible speed and auto-negotiation combinations for a line between two 10/100/1000 Base-T Ethernet interfaces.
PAGE 647
• For the management port, enter the keyword managementethernet then the slot (0 or 1) and the port (0). • For a Tunnel interface, enter the keyword tunnel then the slot/port. The range is from 1 to 16383. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a VLAN interface, enter the keyword vlan then the slot/port.
PAGE 648
Example (Single Interface) Key Description m Change the view from a single interface to all interfaces on the line card or visa-versa. c Refresh the view. b Change the counters displayed from Packets on the interface to Bytes. r Change the [delta] column from change in the number of packets/bytes in the last interval to rate per second. l Change the view to the next interface on the line card, or if in line card mode, the next line card in the chassis.
PAGE 649
Gi 0/1 Down 0 0 0 0 Gi 0/2 Up 61512 52 66160 42 Gi 0/3 Up 63086 20 9405888 24 Gi 0/4 Up 14697471418 2661481 13392989657 2661385 Gi 0/5 Up 3759 3 161959604 832816 Gi 0/6 Up 4070 3 8680346 5 Gi 0/7 Up 61934 34 138734357 72 Gi 0/8 Up 61427 1 59960 1 Gi 0/9 Up 62039 53 104239232 3 Gi 0/10 Up 17740044091 372 7373849244 79 Gi 0/11 Up 18182889225 44 7184747584 138 Gi 0/12 Up 18182682056 0 3682 1 Gi 0/13 Up 18182681434 43 6592378911 144 Gi 0/14 Up 61349 55 86281941 15 Gi 0/15 Up 59808 58 62060 27 Gi 0/16 Up 59889 1
PAGE 650
Usage Information Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series. If the packet includes a Layer 2 header, the difference between the link MTU and IP MTU (ip mtu command) must be enough bytes to include the Layer 2 header. When you enter the no mtu command, Dell Networking OS reduces the IP MTU value to 1536 bytes.
PAGE 651
portmode hybrid To accept both tagged and untagged frames, set a physical port or port-channel. A port configured this way is identified as a hybrid port in report displays. Z9000 Syntax portmode hybrid To return a port to accept either tagged or untagged frames (non-hybrid), use the no portmode hybrid command. Defaults non-hybrid Command Modes INTERFACE (conf-if-interface-slot/port) Command History This guide is platform-specific.
PAGE 652
The following describes the interface vlan command shown in the following example. This example shows unconfiguration of the hybrid port using the no portmode hybrid command. NOTE: Remove all other configurations on the port before you can remove the hybrid configuration from the port.
PAGE 653
NOTE: Because polling occurs every 15 seconds, the number of seconds designated here rounds to the multiple of 15 seconds lower than the entered value. For example, if 44 seconds is designated, it rounds to 30; 45 to 59 seconds rounds to 45. Defaults 299 seconds Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 654
Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series.
PAGE 655
Example Dell(conf)#interface range gigabitethernet 1/1 - 2 Dell(conf-if-range-gi-1/1-2)#show config ! interface GigabitEthernet 1/1 no ip address switchport no shutdown ! interface GigabitEthernet 1/2 no ip address switchport no shutdown Dell(conf-if-range-gi-1/1-2)# show interfaces Display information on a specific physical interface or virtual interface.
PAGE 656
Usage Information Version 8.3.12.1 Updated command output to support multiple IPv6 addresses on S4810. Version 8.3.11.4 Output expanded to support eSR4 optics in Z9000. Version 8.3.11.1 Introduced on the Z9000. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.2 Included SFP and SFP+ optics power detail in the E-Series and C-Series output. Version 8.2.1.0 Added support for 4093 VLANs on the E-Series ExaScale.
PAGE 657
Line Description • Wavelength, F10 unknown—Dell Force10 ID is present, but not able to determine the optics type • Unknown, Non-qualified— if wavelength is reading error, and F10 ID is not present Dell Networking allows unsupported SFP and XFP transceivers to be used, but Dell Networking OS might not be able to retrieve some data about them.
PAGE 658
Line Description – discarded = the sum of runts, giants, CRC, and overrun packets discarded without any processing Output Statistics: Displays output statistics sent out of the interface including: • Number of packets, bytes, and underruns out of the interface • Packet size and the number of those packets outbound to the interface • Number of Multicast, Broadcast, and Unicast packets: – Multicasts = number of MAC multicast packets – Broadcasts = number of MAC broadcast packets – Unicasts = number of
PAGE 659
Output Statistics: 0 packets, 0 bytes, 0 underruns 0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts 0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts 0 Multicasts, 0 Broadcasts, 0 Unicasts 0 throttles, 0 discarded, 0 collisions, 0 wreddrops Rate info (interval 299 seconds): Input 00.00 Mbits/sec, 0 packets/sec, 0.00% of line-rate Output 00.00 Mbits/sec, 0 packets/sec, 0.
PAGE 660
Time since last interface status change: 1w0d5h Dell# Example (ManagementE thernet) Dell#show interfaces managementethernet 0/0 Example (ManagementE thernet, two IPv6 addresses) Dell#show interfaces managementethernet 0/0 ManagementEthernet 0/0 is up, line protocol is up Hardware is Force10Eth, address is 00:01:e8:0b:a9:4c Current address is 00:01:e8:0b:a9:4c Pluggable media not present Interface index is 503595208 Internet address is 10.11.201.
PAGE 661
Last clearing of "show interface" counters 00:06:14 Queueing strategy: fifo Input 791 packets, 62913 bytes, 775 multicast Received 0 errors, 0 discarded Output 21 packets, 3300 bytes, 20 multicast Output 0 errors, 0 invalid protocol Time since last interface status change: 00:06:03 Example (OpenFlow instance) Dell#show interfaces vlan 6 Vlan 6 is down, line protocol is down Address is 00:01:e8:8a:e1:8c, Current address is 00:01:e8:8a:e1:8c Interface index is 1107525638 of-instance: 2 Internet address is no
PAGE 662
show interfaces configured Display any interface with a non-default configuration. Z9000 Syntax show interfaces configured Command Modes • EXEC • EXEC Privilege Command History Example 662 Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.
PAGE 663
Time since last interface status change: 00:04:59 Dell# Related Commands show interfaces — displays information on a specific physical interface or virtual interface. show interfaces dampening Display interface dampening information. Z9000 Syntax Parameters show interfaces dampening [[interface] [summary] [detail]] interface (Optional) Enter one of the following keywords and slot/port or number information: • For a Port Channel interface, enter the keywords portchannel then a number.
PAGE 664
Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced Example Dell#show interfaces dampening Interface Supp Flaps Penalty Half-Life Reuse Suppress Max-Sup State Gi 3/2 Up 0 0 20 800 4500 120 Gi 3/10 Up 0 0 5 750 2500 20 Dell# Related Commands dampening — configures dampening on an interface. show interfaces — displays information on a specific physical interface or virtual interface.
PAGE 665
Usage Information The following describes the show interfaces gigabitethernet command following example. Mode Control Indicates if auto negotiation is enabled. If so, indicates the selected speed and duplex. Mode Status Displays auto negotiation fault information. When the interface completes auto negotiation successfully, the autoNegComplete field and the linkstatus field read “True.” AutoNegotiatio n Advertise Displays the control words the local interface advertises during negotiation.
PAGE 666
• Auto • 1000MB • 100MB • 10MB Example Dell#show int gigabitethernet 1/0 phy Mode Control: SpeedSelection: 10b AutoNeg: ON Loopback: False PowerDown: False Isolate: False DuplexMode: Full Mode Status: AutoNegComplete: False RemoteFault: False LinkStatus: False JabberDetect: False AutoNegotation Advertise: 100MegFullDplx: True 100MegHalfDplx: True 10MegFullDplx: False 10MegHalfDplx: True Asym Pause: False Sym Pause: False AutoNegotiation Remote Partner's Ability: 100MegFullDplx: False 100MegHalfDplx
PAGE 667
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series.
PAGE 668
show interfaces status Z9000 Syntax Parameters show interfaces [interface | linecard slot-number] status interface linecard slotnumber (OPTIONAL) Enter one of the following keywords and slot/ port or number information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
PAGE 669
Gi 0/0 Up 1000 Mbit Auto -Gi 0/1 Down Auto Auto 1 Gi 0/2 Down Auto Auto 1 Gi 0/3 Down Auto Auto -Gi 0/4 DellPort Up 1000 Mbit Auto 30-130 Gi 0/5 Down Auto Auto -Gi 0/6 Down Auto Auto -Gi 0/7 Up 1000 Mbit Auto 1502,1504,1506-1508,1602 Gi 0/8 Down Auto Auto -Gi 0/9 Down Auto Auto -Gi 0/10 Down Auto Auto -Gi 0/11 Down Auto Auto -Gi 0/12 Down Auto Auto -Gi 0/13 Down Auto Auto -Gi 0/14 Down Auto Auto -Gi 0/15 Down Auto Auto Dell# Related Commands show interfaces — displays information on a specific physical int
PAGE 670
The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.2.1.0 Added support for 4093 VLANs on E-Series ExaScale. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.
PAGE 671
Vlan 2 --More-Related Commands interface — configures a physical interface on the switch. show ip interface — displays Layer 3 information about the interfaces. show interfaces — displays information on a specific physical interface or virtual interface. show interfaces transceiver — displays the physical status and operational status of an installed transceiver. The output also displays the transceiver’s serial number.
PAGE 672
Usage Information 672 Version 7.6.1.0 Introduced on the C-Series and S-Series. Version 6.5.4.0 Introduced on the E-Series. The following describes the show interfaces transceiver command shown in the following example. Line Description Rx Power measurement type Output depends on the vendor, typically either “Average” or “OMA” (Receiver optical modulation amplitude). Temp High Alarm threshold Factory-defined setting, typically in Centigrade. Value differs between SFPs and SFP+.
PAGE 673
Interfaces Line Description Temp Low Warning threshold Factory-defined setting. Value can differ between SFP and SFP+. Voltage Low Warning threshold Factory-defined setting. Value can differ between SFP and SFP+. Bias Low Warning threshold Factory-defined setting. Value can differ between SFP and SFP+. TX Power Low Warning threshold Factory-defined setting. Value can differ between SFP and SFP+. Power Low Warning threshold Factory-defined setting. Value can differ between SFP and SFP+.
PAGE 674
Line Description RS state This is the reserved digital state of the pin AS(1) per SFF-8079 and RS(1) per SFF-8431. Tx Disable state If the admin status of the port is down then this flag is set to true. Temperature High Alarm Flag This can be either true or false, depending on the Current voltage value displayed above. Voltage High Alarm Flag This can be either true or false, depending on the Current Temperature value displayed above.
PAGE 675
Example Line Description Tx Bias Low Warning Flag This can be either true or false, depending on the present Tx bias current value displayed above. Tx Power Low Warning Flag This can be either true or false, depending on the Current Tx power value displayed above. Rx Power Low Warning Flag This can be either true or false, depending on the Current Rx power value displayed above. Dell#show interfaces gigabitethernet 1/0 transceiver SFP is present.
PAGE 676
SFP 1 RX Power Low Warning threshold = 0.016mW =================================== SFP 1 Temperature = 39.930C SFP 1 Voltage = 3.293V SFP 1 Tx Bias Current = 6.894mA SFP 1 Tx Power = 0.328mW SFP 1 Rx Power = 0.
PAGE 677
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Added support for 4093 VLANs on E-Series ExaScale. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.1.1.0 Introduced.
PAGE 678
Related Commands ecmp-group — configures a mechanism to monitor traffic distribution. shutdown Disable an interface. Z9000 Syntax shutdown To activate an interface, use the no shutdown command. Defaults The interface is disabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 679
Related Commands interface port-channel — creates a port channel interface. interface vlan — creates a VLAN. show ip interface — displays the interface routing status. Add the keyword brief to display a table of interfaces and their status. speed (for 10/100/1000 interfaces) Set the speed for 10/100/1000 Base-T Ethernet interfaces. Set both sides of a link to the same speed (10/100/1000) or to auto or the link may not come up.
PAGE 680
The following is a list of the Dell Networking OS version history for this command. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Supported on LC-EH-GE-50P or the LC-EJ-GE-50P cards. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series.
PAGE 681
1000 Enter the keyword 1000 to set the interface to autonegotiate its speed. auto Enter the keyword auto to set the interface to autonegotiate its speed. Defaults auto Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 682
number Enter the port number of the 40G port to be split. The range is from 0 to 124 in multiples of 4 (0, 4, 8, 12, ... 120 124). Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.
PAGE 683
tengigabit slot/port | fortyGigE slot/port | port-channel number} command. Parameters backup interface Use this option to configure a redundant Layer 2 link without using Spanning Tree. The keywords backup interface configures a backup port so that if the primary port fails, the backup port changes to the up state. If the primary later comes up, it becomes the backup. gigabit Enter the keyword gigabit if the backup port is a 1G port.
PAGE 684
Usage Information If an IP address or VRRP group is assigned to the interface, you cannot use the switchport command on the interface. To use the switchport command on an interface, only the no ip address and no shutdown statements must be listed in the show config output. When you enter the switchport command, the interface is automatically added to the default VLAN. To use the switchport backup interface command on a port, first enter the switchport command.
PAGE 685
all • For Telnet, enter the keyword telnet. • For TFTP, enter the keyword tftp. Configure all applications. Defaults None. Command Modes EIS Mode (conf-mgmt-eis) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2. (0.0) Introduced on the Z9000, S4810, and S4820T.
PAGE 686
Version 9.3. (0.0) Added support for the HTTP and ICMP traffic on the Z9000, S4810, and S4820T. clear management application pkt-cntr Clear management application packet counters for all management application types. Z9000 Syntax clear management application pkt-cntr Defaults None. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 687
management egress-interface-selection To make configured application traffic egress through the management port instead of the front-end (FE) port, enable and configure a management egress interface. Z9000 Syntax management egress-interface-selection To disable and remove management egress interface selection (EIS) configurations, use the no management egress-interface-selection command. Defaults None. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 688
show management application pkt-cntr Display the number of packets for each application type that have taken the management route. Z9000 Syntax show management application pkt-cntr Defaults None. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2. (0.
PAGE 689
Version 9.2. (0.0) Example Introduced on the Z9000, S4810, and S4820T. Dell#show management dns : ftp : ntp : radius : sflow-collector : snmp : ssh : syslog : tacacs : telnet : tftp : application pkt-fallback-cntr 0 0 0 0 0 0 2 0 0 0 0 Port Channel Commands A Link Aggregation Group (LAG) is a group of links that appear to a MAC client as if they were a single link according to IEEE 802.3ad. In Dell Networking OS, a LAG is referred to as a Port Channel.
PAGE 690
• • • For a Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. Defaults Not configured. Command Modes INTERFACE PORTCHANNEL Command History This guide is platform-specific.
PAGE 691
On the E-Series TeraScale, you can add up to 16 interfaces to a Port Channel; ESeries ExaScale can add up to 64. You can have eight interfaces per Port Channel on the C-Series and S-Series. The interfaces can be located on different line cards but must be the same physical type and speed (for example, all 1-Gigabit Ethernet interfaces). However, you can combine 100/1000 interfaces and GE interfaces in the same Port Channel.
PAGE 692
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.
PAGE 693
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on S4810. Version 8.3.11.1 Introduced on Z9000. Version 8.1.1.0 Introduced on E-Series ExaScale. Version 7.6.1.0 Introduced on S-Series. Version 7.5.1.0 Introduced on C-Series. pre-Version 6.2.1.0 Introduced on E-Series. Port Channel interfaces are logical interfaces and can be either in Layer 2 mode (by using the switchport command) or Layer 3 mode (by configuring an IP address).
PAGE 694
shutdown — disables/enables the port channel. minimum-links Configure the minimum number of links in a LAG (Port Channel) that must be in “oper up” status for the LAG to be also in “oper up” status. Z9000 Syntax Parameters minimum-links number number Enter the number of links in a LAG that must be in “oper up” status. The range is from 1 to 16. The default is 1. Defaults 1 Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 695
port-channel failover-group To configure a LAG failover group, access PORT-CHANNEL FAILOVER-GROUP mode. Z9000 Syntax port-channel failover-group To remove all LAG failover groups, use the no port-channel failover-group command. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 696
show config Display the current configuration of the selected LAG. Z9000 Syntax show config Command Modes INTERFACE PORTCHANNEL Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.
PAGE 697
Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.
PAGE 698
Example 698 Field Description Queueing strategy. States the packet queuing strategy. FIFO means first in first out. packets input... Displays the number of packets and bytes into the interface. Input 0 IP packets... Displays the number of packets with IP headers, VLAN tagged headers, and MPLS headers. The number of packets may not add correctly because a VLAN tagged IP packet counts as both a VLAN packet and an IP packet. 0 64-byte...
PAGE 699
Dell# User Information The following describes the show interfaces port-channel brief command shown in the following example. Field Description LAG Lists the port channel number. Mode Lists the mode: Status Example • L3 — for Layer 3 • L2 — for Layer 2 Displays the status of the port channel. • down — if the port channel is disabled (shutdown) • up — if the port channel is enabled (no shutdown) Uptime Displays the age of the port channel in hours:minutes:seconds.
PAGE 700
Parameters outgoing-portchannel number Enter the keywords outgoing-port-channel then the number of the port channel to display flow information. incominginterface interface Enter the keywords incoming-interface then the interface type and slot/port or number information: • For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 701
Usage Information Because this command calculates based on a Layer 2 hash algorithm, use this command to display flows for switched Layer 2 packets, not for routed packets (use the show ip flow command to display routed packets). The show port-channel-flow command returns the egress port identification in a given port-channel if a valid flow is entered. A mismatched flow error occurs if MAC-based hashing is configured for a Layer 2 interface and you are trying to display a Layer 3 flow.
PAGE 702
tdr-cable-test Test the condition of copper cables on 100/1000 Base-T modules. Z9000 Syntax Parameters tdr-cable-test interface interface Enter the keyword GigabitEthernet then the slot/port information for the 100/1000 Ethernet interface. Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 703
show tdr Display the TDR test results. Z9000 Syntax Parameters show tdr interface interface Enter the keyword GigabitEthernet then the slot/port information for the 100/1000 Ethernet interface. Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 704
Status Definition Status: Impedance Mismatch There is an impedance mismatch in the cables. Example Dell#show tdr gigabitethernet 10/47 Time since last test: 00:00:02 Pair A, Length: OK Status: Terminated Pair B, Length: 92 (+/- 1) meters, Status: Short Pair C, Length: 93 (+/- 1) meters, Status: Open Pair D, Length: 0 (+/- 1) meters, Status: Impedance Mismatch Related Commands tdr-cable-test — runs the TDR test.
PAGE 705
Example Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Pre-version 8.3.7.0 Introduced on the E-Series ExaScale. Dell#debug ip udp-helper UDP helper debugging is on 01:20:22: Pkt rcvd on Gi 5/0 with IP DA (0xffffffff) will be sent on Gi 5/1 Gi 5/2 Vlan 3 01:44:54: Pkt rcvd on Gi 7/0 is handed over for DHCP processing. Related Commands ip udp-broadcast-address — configures a UDP IP address for broadcast.
PAGE 706
Version 8.3.7.0 Introduced on the S4810. Pre-version 8.3.7.0 Introduced on the E-Series ExaScale. Usage Information When a UDP broadcast packet is flooded out of an interface, and the outgoing interface is configured using this command, the outgoing packet’s IP destination address is replaced with the configured broadcast address. Related Commands debug ip udp-helper — enables debug and displays the debug information on a console.
PAGE 707
Usage Information If you configure the ip helper-address command and ip udp-helper udpport command, the behavior is that the UDP broadcast traffic with port numbers 67/68 is unicast relayed to the DHCP server per the ip helper-address configuration. This occurs regardless if the ip udp-helper udp-port command contains port numbers 67/68 or not.
PAGE 708
Related Commands debug ip udp-helper — enables debug and displays the debug information on a console. ip udp-broadcast-address — configures a UDP IP address for broadcast. ip udp-helper udp-port — enables the UDP broadcast feature on an interface either for all UDP ports or a specified list of UDP ports. Enhanced Validation of Interface Ranges This functionality is supported on the Z9000 platform.
PAGE 709
Internet Protocol Security (IPSec) 22 Internet protocol security (IPSec) is an end-to-end security scheme for securing IP communications by authenticating and encrypting all packets in a session. Use IPSec between hosts, gateways, or hosts and gateways. IPSec uses a series of protocol functions to achieve information security: • Authentication Headers (AH) — Connectionless integrity and origin authentication for IP packets.
PAGE 710
To delete a transform set, use the no crypto ipsec transform-set name {ah-authentication {md5|sha1|null} | esp-authentication {md5| sha1|null} | esp-encryption {3des|cbc|des|null}} command. Parameters name Enter the name for the transform set. ahauthentication Enter the keywords ah-authentication then the transform type of operation to apply to traffic. The transform type represents the encryption or authentication applied to traffic.
PAGE 711
Usage Information Example • Both sides of the link must specify the same transform set. • You can create up to 64 transform sets. Dell(conf)#int ten 0/4 Dell(conf-if-te-0/4)#ipv6 address 200:1::/64 eui64 Dell(conf)#int ten 0/6 Dell(conf-if-te-0/6)#ipv6 address 801:10::/64 eui64 crypto ipsec policy Create a crypto policy used by ipsec. Z9000 Syntax crypto ipsec policy name seq-num ipsec-manual To delete a crypto policy entry, use the no crypto ipsec policy name seqnum ipsec-manual command.
PAGE 712
management crypto-policy Apply the crypto policy to management traffic. Z9000 Syntax management crypto-policy name To remove the management traffic crypto policy, use the no management crypto-policy name command. Parameters name Enter the name for the crypto policy.. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 713
source-port number Enter the source port number. destinationport number Enter the destination port number. Defaults none Command Modes CONFIG-CRYPTO-POLICY Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.2) Usage Information Example • Introduced on the Z9000, S4810, and S4820T.
PAGE 714
outbound Specify the outbound session key for IPSec. ah Use the AH protocol when you select the AH transform set in the crypto policy. esp Use the ESP protocol when you select the ESP transform set in the crypto policy. spi Enter the security parameter index number. hex-key-string Enter the session key in hex format (a string of 8, 16, or 20 bytes). For DES algorithms, specify at least 16 bytes per key. For SHA algorithms, specify at least 20 bytes per key.
PAGE 715
Version 9.2(0.2) Example Introduced on the Z9000, S4810, and S4820T. Dell#show crypto ipsec transform-set Transform-Set Name Transform-Set refCnt AH Transform ESP Auth Transform ESP Encry Transform Dell# : dallas : 0 : : : 3des show crypto ipsec policy Display the crypto policy configuration. Z9000 Syntax show crypto ipsec policy Command Modes EXEC Command History This guide is platform-specific.
PAGE 716
Protocol type IP or IPv6 Source address Source mask Source port Destination address Destination mask Destination port source-interface name source-interface num : : : : : : : : : : tcp IPv6 a::1 /128 0 a::2 /128 23 Match sequence Num Protocol type IP or IPv6 Source address Source mask Source port Destination address Destination mask Destination port source-interface name source-interface num : : : : : : : : : : : 1 tcp IPv6 a::1 /128 23 a::2 /128 0 Match sequence Num Protocol type IP or IPv6 Source ad
PAGE 717
transform-set Specify the transform set the crypto policy uses. Z9000 Syntax transform-set transform-set-name To delete a transform set from the crypto policy, use the no transform-set transform-set-name command. Parameters transform-setname Enter the name for the crypto policy transform set. Defaults none Command Modes CONFIG-CRYPTO-POLICY Command History This guide is platform-specific.
PAGE 718
PAGE 719
23 IPv4 Routing The basic IPv4 commands are supported by Dell Networking operating system on the Z9000 platform. arp To associate an IP address with a MAC address in the switch, use address resolution protocol (ARP). Z9000 Syntax arp ip-address mac-address interface To remove an ARP address, use the no arp ip-address command. Parameters ip-address Enter an IP address in dotted decimal format. mac-address Enter a MAC address in nnnn.nnnn.nnnn format.
PAGE 720
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series. Usage Information You cannot use Class D or Class E IP addresses or zero IP address (0.0.0.
PAGE 721
Version 8.3.8.0 Introduced on the S4810. Usage Information This timer is an exponential backoff timer. Over the specified period, the time between ARP requests increases. This behavior reduces the potential for the system to slow down while waiting for a multitude of ARP responses. Related Commands show arp retries — displays the configured number of ARP retries. arp learn-enable Enable ARP learning using gratuitous ARP.
PAGE 722
arp max-entries Enables you to configure the maximum number of ARP entries per VRF that are allowed for IPv4.. Syntax Parameters arp max-entries [vrf vrf-name] max-number vrf vrf-name Enter the name of a specific VRF for which you want to configure maximum number of ARP entries that IPv4 allows. max-number Enter the maximum number of ARP entries that a VRF RTM can hold. The range is from 0 to 65535. Defaults Not configured.
PAGE 723
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Introduced. Usage Information Retries are 20 seconds apart.
PAGE 724
Related Commands Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. show interfaces — displays the ARP timeout value for all available interfaces. clear arp-cache Clear the dynamic ARP entries from a specific interface or optionally delete (no-refresh) ARP entries from the content addressable memory (CAM).
PAGE 725
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.3.7.
PAGE 726
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. clear ip fib stack-unit Clear all FIB entries in the specified stack unit (use this command with caution, refer to Usage Information.
PAGE 727
clear ip route Clear one or all routes in the routing table. Z9000 Syntax Parameters clear ip route {* | ip-address mask} * Enter an asterisk (*) to clear all learned IP routes. ip-address mask Enter a specific IP address and mask in dotted decimal format to clear that IP address from the routing table. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 728
clear tcp statistics Clear TCP counters. Z9000 Syntax Parameters clear tcp statistics [all | cp | rp1 | rp2] all Enter the keyword all to clear all TCP statistics maintained on all switch processors. cp (OPTIONAL) Enter the cp to clear only statistics from the Control Processor. rp1 (OPTIONAL) Enter the keyword rp1 to clear only the statistics from Route Processor 1. rp2 (OPTIONAL) Enter the keyword rp2 to clear only the statistics from Route Processor 2.
PAGE 729
To stop debugging ARP transactions, use the no debug arp command. Parameters interface count value (OPTIONAL) Enter the following keywords and slot/port or number information: • For a 1-Gigabit Ethernet interface, enter the keyword Gigabitethernet then the slot/port information. • For the Management interface, enter the keyword ManagementEthernet then the slot/port information. The slot range is from 0 to 1 and the port range is 0.
PAGE 730
Usage Information To stop packets from flooding the user terminal when debugging is turned on, use the count option. debug ip dhcp Enable debug information for dynamic host configuration protocol (DHCP) relay transactions and display the information on the console. Z9000 Syntax debug ip dhcp To disable debug, use the no debug ip dhcp command. Defaults Debug disabled Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 731
00:12:40 : %RELAY-I-PACKET: BOOTP REQUEST (Unicast) received at interface 113.3.3.17 BOOTP Request, hops = 0, XID = 0xda4f9503, secs = 0, hwaddr = 00:60:CF:20:7B:8C, giaddr = 0.0.0.0 00:12:40 : %RELAY-I-BOOTREQUEST: Forwarded BOOTREQUEST for 00:60:CF:20:7B:8C to 14.4.4.2 00:12:42 : %RELAY-I-PACKET: BOOTP REPLY (Unicast) received at interface 14.4.4.1 BOOTP Reply, hops = 0, XID = 0xda4f9503, secs = 0, hwaddr = 00:60:CF:20:7B: 8C, giaddr = 113.3.3.
PAGE 732
count value • For a Tunnel interface, enter the keywords tunnel then a number. The range is from 1 to 16383. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a VLAN, enter the keyword vlan then a number from 1 to 4094. (OPTIONAL) Enter the keyword count then the count value. The range is from 1 to 65534. The default is Infinity.
PAGE 733
debug ip packet View a log of IP packets sent and received. Z9000 Syntax debug ip packet [access-group name] [count value] [interface] To disable debugging, use the no debug ip packet [access-group name] [count value] [interface] command. Parameters access-group name Enter the keyword access-group then the access list name (maximum 16 characters) to limit the debug output based on the defined rules in the ACL. count value (OPTIONAL) Enter the keyword count then the count value.
PAGE 734
Usage Information Example 734 Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Added support for 4094 VLANs on the E-Series ExaScale (the prior limit was 2094). Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Added the access-group option. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.3.1.0 Added the count option.
PAGE 735
UDP src=0, dst=0 IP: s=10.1.2.62 (local), d=10.1.2.3 (Ma 0/0), len 1500, sending fragment IP Fragment, Ident = 4741, fragment offset = 0 ICMP type=0, code=0 IP: s=10.1.2.62 (local), d=10.1.2.3 (Ma 0/0), len 1500, sending fragment IP Fragment, Ident = 4741, fragment offset = 1480 IP: s=40.40.40.40 (local), d=224.0.0.5 (Gi 4/11), len 64, sending broad/multicast proto=89 IP: s=40.40.40.40 (local), d=224.0.0.6 (Gi 4/11), len 28, sending broad/multicast proto=2 IP: s=0.0.0.0, d=30.30.30.
PAGE 736
ip address Assign a primary and secondary IP address to the interface. Z9000 Syntax ip address ip-address mask [secondary] To delete an IP address from an interface, use the no ip address [ipaddress] command. Parameters ip-address Enter an IP address in dotted decimal format. mask Enter the mask of the IP address in slash prefix format (for example, /24). secondary (OPTIONAL) Enter the keyword secondary to designate the IP address as the secondary address. Defaults Not configured.
PAGE 737
ip directed-broadcast Enables the interface to receive directed broadcast packets. Z9000 Syntax ip directed-broadcast To disable the interface from receiving directed broadcast packets, use the no ip directed-broadcast command. Defaults Disabled (that is, the interface does not receive directed broadcast packets) Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 738
Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.
PAGE 739
Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.
PAGE 740
Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810.
PAGE 741
Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Added support for IPv6. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.
PAGE 742
To re-enable the hop-count increment, use the no ip helper-address hopcount disable command. Defaults Enabled; the hops field in the DHCP message header is incremented by default. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
PAGE 743
Parameters name Enter a text string to associate with one IP address. ip address Enter an IP address, in dotted decimal format, to be mapped to the name. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
PAGE 744
NOTE: When you configure the capability to enable the loopback IP address to be sent for easy debugging and diagnosis (IP addresses of the devices for which the ICMP source interface is configured), the source IP address of the outgoing ICMP error message is modified, although the packets are not sent out using the configured interface.
PAGE 745
Example Dell(conf)#ip icmp source-interface tengigabitethernet 0/0 Dell(conf)# ipv6 icmp source-interface Enable the ICMP error and unreachable messages to be sent with the source interface IP address, such as the loopback address, instead of the hops of the preceding devices along the network path to be used for easy debugging and diagnosis of network disconnections and reachability problems with IPv6 packets. This functionality is supported on the , , , and Z9000 platforms.
PAGE 746
Usage Information You can enable the mechanism to configure the source or the originating interface from which the packet (the device that generates the ICMP error messages) is received by the switch to send the loopback address instead of its source IP address to be used in the ICMP unreachable messages and in the traceroute command output. The loopback address must be unique in a particular domain.
PAGE 747
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced for the E-Series. To avoid denial of service (DOS) attacks, keep the number of fragments allowed for re-assembly low.
PAGE 748
Related Commands show ip route — views the switch routing table. show ipv6 route — displays the IPv6 routes. ip mtu Set the IP MTU (frame size) of the packet the RPM transmits for the line card interface. If the packet must be fragmented, Dell Networking OS sets the size of the fragmented packets to the size specified in this command. Syntax ip mtu value To return to the default IP MTU value, use the no ip mtu command. Parameters value Enter the maximum MTU size if the IP packet is fragmented.
PAGE 749
Layer 2 header, the difference between the link MTU and IP MTU (the ip mtu command) must be enough bytes to include for the Layer 2 header. Link MTU and IP MTU considerations for Port Channels and VLANs are as follows Port Channels: • All members must have the same link MTU value and the same IP MTU value. • The Port Channel link MTU and IP MTU must be less than or equal to the link MTU and IP MTU values configured on the channel members.
PAGE 750
ip name-server Enter up to six IPv4 addresses of name servers. The order you enter the addresses determines the order of their use. Z9000 Syntax ip name-server ipv4-address [ipv4-address2...ipv4-address6] To remove a name server, use the no ip name-server ip-address command. Parameters ipv4-address Enter the IPv4 address, in dotted decimal format, of the name server to be used. ipv4-address2...
PAGE 751
ip proxy-arp Enable proxy ARP on an interface. Z9000 Syntax ip proxy-arp To disable proxy ARP, use the no ip proxy-arp command. Defaults Enabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 752
To delete all routes matching a certain route, use the no ip route destination mask command. Parameters destination Enter the IP address in dotted decimal format of the destination device. mask Enter the mask in the slash prefix format (/x) of the destination IP address. ip-address Enter the IP address of the forwarding router in dotted decimal format. interface ipaddress Enter the keyword interface then the IP address.
PAGE 753
Usage Information Related Commands Version 8.2.1.0 Added support for 4094 VLANs on the E-Series ExaScale (the prior limit was 2094). Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.9.1.0 Introduced VRF on the E-Series. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. Using the following example of a static route: ip route 33.33.33.0 /24 tengigabitethernet 0/0 172.31.5.
PAGE 754
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. ip tcp initial-time Define the wait duration in seconds for the TCP connection to be established. This command is supported on the , , , and Z9000 platforms.
PAGE 755
show ip tcp initial-time Displays the interval that you configured for the device to wait before the TCP connection is attempted to be established. This command is supported on the , , , Z9000, and MXL platforms. Syntax show ip tcp initial-time Command Modes EXEC EXEC Privilege Command History Version 9.3(0.0) Introduced on the S4810, S4820T, S6000, Z9000, and MXL platforms. ip unreachables Enable the generation of internet control message protocol (ICMP) unreachable messages.
PAGE 756
pre-Version 6.1.1.0 Introduced on the E-Series. load-balance By default, for C-Series and S-Series, Dell Networking OS uses an IP 4-tuple (IP SA, IP DA, Source Port, and Destination Port) to distribute IP traffic over members of a Port Channel as well as equal-cost paths. To designate another method to balance traffic over Port Channel members, use the load-balance command.
PAGE 757
tcp-udp enable Enter the keywords to distribute traffic based on the following: • ingress-port enable enable — Takes the TCP/UDP source and destination ports into consideration when doing hash computations. This option is enabled by default. Enter the keywords to distribute traffic based on the following: • enable — Takes the source port into consideration when doing hash computations. This option is disabled by default.
PAGE 758
load-balance hg Choose the traffic flow parameters the hash calculation uses while distributing the traffic across internal higig links.
PAGE 759
mac [sourcemac | sourceport-id | sourcemodule-id | dest-mac | dest-port-id | dest-moduleid | vlan | ethertype | source-destmac ] tunnel [ipv4over-ipv4 | ipv4-over-greipv4 | mac-inmac]} To use MAC key fields in hash computation, enter the keyword mac then one of the parameters: • source-mac — Use source-mac field in hash calculation. • source-port-id — Use src-port-id field in hash calculation. • source-module-id — Use src-module-id field in hash calculation.
PAGE 760
management route Configure a static route that points to the Management interface or a forwarding router. Z9000 Syntax management route {{ip-address mask | {ipv6-address prefixlength}} {forwarding-router-address | managementethernet} To remove a static route, use the no management route{{ip-address mask | {ipv6-address prefix-length}}{forwarding-router-address | managementethernet} command.
PAGE 761
pre-Version 6.1.1.0 Introduced on the E-Series. Usage Information When a static route (or a protocol route) overlaps with Management static route, the static route (or a protocol route) is preferred over the Management Static route. Also, Management static routes and the Management Connected prefix are not reflected in the hardware routing tables. Separate routing tables are maintained for IPv4 and IPv6 management routes. This command manages both tables.
PAGE 762
• statistics — view DAI statistics macaddress mac-address mask (OPTIONAL) Enter the keyword macaddress then a MAC address in nn:nn:nn:nn:nn:nn format. Enter the optional MAC address mask in nn:nn:nn:nn:nn format also. static (OPTIONAL) Enter the keyword static to view entries entered manually. retries (OPTIONAL) Enter the keyword retries to show the number of ARP retries before a 20–second back off. dynamic (OPTIONAL) Enter the keyword dynamic to view dynamic entries.
PAGE 763
Usage Information The following example shows two VLANs that are associated with a private VLAN (PVLAN) (refer to Private VLAN (PVLAN)). If you have entered the clear arp-cache command to remove a large number of ARP entries and the command is still being processed in the background, an error message display if you attempt to enter the show arp command: Clear arp in-progress. Please try after sometime! The following describes the show arp command shown in the following example.
PAGE 764
CP Internet 10.16.134.254 20 00:01:e8:d5:9e:e2 CP Internet 133.33.33.4 1 00:01:e8:d5:9e:e2 CP Usage Information Ma 0/0 Ma 0/0 The following describes the show arp summary command shown in the following example. Description Total Entries Lists the total number of ARP entries in the ARP table. Static Entries Lists the total number of configured or static ARP entries. Dynamic Entries Lists the total number of learned or dynamic ARP entries. CPU Lists which CPU the entries are stored on.
PAGE 765
Related Commands Version 8.3.11.1 Introduced on the Z9000. Version 8.3.1.0 Introduced. arp retries — sets the number of ARP retries in case the system does not receive an ARP reply in response to an ARP request. show hosts View the host table and DNS configuration. Z9000 Syntax show hosts Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 766
Field Description • If DNS is not enabled, the Name/Address lookup is static mapping Name servers are... Lists the name servers, if configured. Host Displays the host name assigned to the IP address. Flags Classifies the entry as one of the following: • perm — the entry was manually configured and will not time out • temp — the entry was learned and will time out after 72 hours of inactivity.
PAGE 767
show ip cam linecard View CAM entries for a port pipe on a line card. Syntax Parameters show ip cam linecard number port-set pipe-number [ip-address mask [longer-prefixes] | index index-number | summary | vrf vrf instance] number Enter the number of the line card. pipe-number Enter the number of the line card’s port-pipe. The range is from 0 to 1. ip-address mask [longerprefix] (OPTIONAL) Enter the IP address and mask of a route to CAM entries for that route only.
PAGE 768
Usage Information Example 768 The following describes the show ip cam command shown in the following example. Field Description Index Displays the CAM index number of the entry. Destination Displays the destination route of the index. EC Displays the number of equal cost multipaths (ECMP) available for the default route for non-Jumbo line cards. For Jumbo line cards, displays 0,1 when ECMP is more than eight. CG Displays 0.
PAGE 769
Usage Information Example (Summary) The following describes the show ip cam summary command shown in the following example. Field Description Prefix Length Displays the prefix-length or mask for the IP address configured on the linecard 0 port pipe 0. Current Use Displays the number of routes currently configured for the corresponding prefix or mask on the linecard 0 port pipe 0. Initial Size Displays the CAM size Dell Networking OS allocates for the corresponding mask.
PAGE 770
show ip cam stack-unit Display CAM entries for an S-Series or Z-Series switch. Z9000 Syntax Parameters show ip cam stack-unit {id} [port-set {pipe-number} | hostname {ip-address mask [longer-prefixes [ecmp-group detail]]}| ecmpgroup {detail | member-info [detail [group-index indexnumber]]}| summary] id Enter the stack-unit ID. The unit ID range is from 0 to 7 for the Z9000. port-set pipenumber Enter the keyword port-set then the number of the stack unit’s port-pipe.
PAGE 771
The following is a list of the Dell Networking OS version history for this command. Usage Information Example Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Added support for up to seven stack members. Version 7.6.1.0 Introduced on the S-Series. The following describes the show ip cam command shown in the following example. Field Description Destination Displays the destination route of the index.
PAGE 772
Field Description Prefix Length Displays the prefix-length or mask for the IP address configured on the linecard 0 port pipe 0. Current Use Displays the number of routes currently configured for the corresponding prefix or mask on the linecard 0 port pipe 0. Initial Size Displays the CAM size Dell Networking OS allocates for the corresponding mask. Dell Networking OS adjusts the CAM size if the number of routes for the mask exceeds the initial allocation.
PAGE 773
ip-address mask (OPTIONAL) Enter the IP address of the network destination to view only information on that destination. Enter the IP address is dotted decimal format (A.B.C.D). Enter the mask in slash prefix format (/X). longer-prefixes (OPTIONAL) Enter the keywords longer-prefixes to view all routes with a common prefix. summary (OPTIONAL) Enter the keyword summary to view the total number of prefixes in the FIB.
PAGE 774
Example Dell>show ip fib linecard 12 Destination Gateway First-Hop Mac-Addr Port VId Index EC ------------------------------------------------------------------------------3.0.0.0/8 via 100.10.10.10, So 2/8 100.10.10.10 00:01:e8:00:03:ff So 2/8 0 60260 0 3.0.0.0/8 via 101.10.10.10, So 2/9 00.10.10.0/24 Direct, So 2/8 0.0.0.0 00:01:e8:00:03:ff So 2/8 0 11144 0 100.10.10.1/32 via 127.0.0.1 127.0.0.1 00:00:00:00:00:00 CP 0 3276 0 100.10.10.10/32 via 100.10.10.10, So 2/8 100.10.10.
PAGE 775
The following is a list of the Dell Networking OS version history for this command. Usage Information Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Added support for up to seven stack members. Version 7.6.1.0 Introduced on the S-Series. The following describes the show ip fib stack-unit command shown in the following example.
PAGE 776
show ip flow Show how a Layer 3 packet is forwarded when it arrives at a particular interface. Z9000 Syntax Parameters show ip flow interface interface {source-ip address destination-ip address} {protocol number [tcp | udp]} {src-port number destination-port number} interface interface Enter the keyword interface then one of the following interface keywords. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 777
Usage Information Version 7.9.1.0 Introduced VRF on the E-Series. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. This command provides egress port information for a given IP flow. This information is useful in identifying which interface the packet follows in the case of Port-channel and Equal Cost Multi Paths. Use this command for routed packed only.
PAGE 778
• For the Null interface, enter the keyword null then zero (0). • For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a stack-unit interface, enter the keyword stackunit then the stack unit number. The range is from 0 to 7.
PAGE 779
Usage Information Example The following describes the show ip interface command shown in the following example. Lines Description TenGigabitEthern et 0/0... Displays the interface’s type, slot/port, and physical and line protocol status. Internet address... States whether an IP address is assigned to the interface. If an IP address is assigned, that address is displayed. IP MTU is... Displays IP MTU value. Inbound access... Displays the name of the configured incoming access list.
PAGE 780
Example (Brief) Fields Description Protocol States whether IP is enabled (up) or disabled (down) on the interface. Dell#show ip int brief Interface IP-Address Status Protocol GigabitEthernet 1/0 unassigned down down GigabitEthernet 1/1 unassigned down down GigabitEthernet 1/2 unassigned up up GigabitEthernet 1/3 unassigned up up GigabitEthernet 1/4 unassigned up up GigabitEthernet 1/5 10.10.10.
PAGE 781
Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. Dell#show ip management-route Destination ----------10.1.2.0/24 172.16.1.0/24 Dell# Gateway ------ManagementEthernet 0/0 10.1.2.
PAGE 782
Example Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.4.1.0 Introduced on the C- and E-Series. Version 8.3.7.0 Introduced on the S4810. Dell#show ipv6 management-route IPv6 Destination Gateway ---------------------2001:34::0/64 ManagementEthernet 0/0 2001:68::0/64 2001:34::16 Dell# State ----Connected Active show ip protocols View information on all routing protocols enabled and active on the switch.
PAGE 783
pre-Version 6.1.1.0 Example Introduced on the E-Series. Dell#show ip protocols Routing Protocol is "bgp 1" Cluster Id is set to 20.20.20.3 Router Id is set to 20.20.20.3 Fast-external-fallover enabled Regular expression evaluation optimization enabled Capable of ROUTE_REFRESH For Address Family IPv4 Unicast BGP table version is 0, main routing table version 0 Distance: external 20 internal 200 local 200 Neighbor(s): Address : 20.20.20.
PAGE 784
• If you enter isis, you can include the ISIS routingtag. • If you enter ospf, you can include the OSPF processid. process-id (OPTIONAL) Specify that only OSPF routes with a certain process ID must be displayed. routing-tag (OPTIONAL) Specify that only ISIS routes with a certain routing tag must be displayed. connected (OPTIONAL) Enter the keyword connected to view only the directly connected routes. all (OPTIONAL) Enter the keyword all to view both active and non-active routes.
PAGE 785
Example Field Description (undefined) Identifies the type of route: • C = connected • S = static • R = RIP • B = BGP • IN = internal BGP • EX = external BGP • LO = Locally Originated • O = OSPF • IA = OSPF inter area • N1 = OSPF NSSA external type 1 • N2 = OSPF NSSA external type 2 • E1 = OSPF external type 1 • E2 = OSPF external type 2 • i = IS-IS • L1 = IS-IS level-1 • L2 = IS-IS level-2 • IA = IS-IS inter-area • * = candidate default • > = non-active route • + =
PAGE 786
100.10.10.0/24 > R 100.10.10.0/24 C 101.10.10.0/24 > R 101.10.10.
PAGE 787
Example Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series.
PAGE 788
Usage Information Example Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. The following describes the show ip route summary shown in the following example.
PAGE 789
show ip traffic View IP, ICMP, UDP, TCP and ARP traffic statistics. Z9000 Syntax show ip traffic [all | cp | rp1 | rp2] NOTE: These options are supported only on the E-Series. Parameters all (OPTIONAL) Enter the keyword all to view statistics from all processors. If you do not enter a keyword, you also view all statistics from all processors. cp (OPTIONAL) Enter the keyword cp to view only statistics from the Control Processor.
PAGE 790
Keyword Definition unknown protocol... No receiver for these packets. Counts packets whose protocol type field is not recognized by Dell Networking OS. not a gateway... Packets can not be routed; the host/network is unreachable. security failures...
PAGE 791
Example • ARP Statistics: Rcvd: Replies: Object = f10ArpReplyRecv, OIDs = 1.3.6.1.4.1.6027.3.3.5.2.3 • ARP Statistics: Sent: Request: Object = f10ArpReqSent, OIDs = 1.3.6.1.4.1.6027.3.3.5.2.2 • ARP Statistics: Sent: Replies: Object = f10ArpReplySent, OIDs = 1.3.6.1.4.1.6027.3.3.5.2.4 • ARP Statistics: Sent: Proxy: Object = f10ArpProxySent, OIDs = 1.3.6.1.4.1.6027.3.3.5.2.
PAGE 792
cp Enter the keyword cp to view only TCP information from the Control Processor. rp1 Enter the keyword rp1 to view only TCP statistics from Route Processor 1. rp2 Enter the keyword rp2 to view only TCP statistics from Route Processor 2. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 793
Example Field Description 0 partially... Displays the number of partially duplicated packets and bytes received. 7 out-of-order... Displays the number of packets and bytes received out of order. 0 packets with data after window Displays the number of packets and bytes received that exceed the switch’s window size. 0 packets after close Displays the number of packet received after the TCP connection was closed. 0 window probe packets...
PAGE 794
329 packets (1263 bytes) in sequence 17 dup packets (6 bytes) 0 partially dup packets (0 bytes) 7 out-of-order packets (0 bytes) 0 packets ( 0 bytes) with data after window 0 packets after close 0 window probe packets, 41 window update packets 41 dup ack packets, 0 ack packets with unsend data 10184 ack packets (12439508 bytes) Sent: 12007 Total, 0 urgent packets 25 control packets (including 24 retransmitted) 11603 data packets (12439677 bytes) 24 data packets (7638 bytes) retransmitted 355 ack only packet
PAGE 795
IPv6 Access Control Lists (IPv6 ACLs) 24 IPv6 ACLs and IPv6 Route Map commands are supported on Dell Networking Z9000 platform. NOTE: For IPv4 ACL commands, refer to the Access Control Lists (ACL) chapter. Important Points to Remember • Certain platforms require manual CAM usage space allotment. For more information, refer to the cam-acl command. • Egress IPv6 ACL and IPv6 ACL on the Loopback interface is not supported. • Reference to an empty ACL permits any traffic.
PAGE 796
Example Version 8.3.19.0 Introduced on the S4820T. Version 8.3.7.0 Introduced on the S4810. Version 8.4.2.1 Introduced on the S-Series. Version 8.4.2.0 Introduced on the E-Series TeraScale. Version 7.8.1.0 Introduced on the C-Series.
PAGE 797
Example Version 8.4.2.1 Introduced on the S-Series. Version 8.4.2.0 Introduced on the E-Series TeraScale. Version 7.8.1.0 Introduced on the C-Series.
PAGE 798
permit icmp To allow all or specific internet control message protocol (ICMP) messages, configure a filter. Syntax permit icmp {source address mask | any | host ipv6-address} {destination address | any | host ipv6-address} [message-type] [count [byte]] | [log] [monitor] To remove this filter, you have two choices: • Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 799
permit To configure a filter that matches the filter criteria, select an IPv6 protocol number, ICMP, IPv6, TCP, or UDP. Syntax permit {ipv6-protocol-number | icmp | ipv6 | tcp | udp} To remove this filter, you have two choices: Parameters • Use the no seq sequence-number command syntax if you know the filter’s sequence number • Use the no permit {ipv6-protocol-number | icmp | ipv6 | tcp | udp} command ip-protocolnumber Enter an IPv6 protocol number. The range is from 0 to 255.
PAGE 800
ipv6 control-plane egress-filter Enable egress Layer 3 ACL lookup for IPv6 CPU traffic. Z9000 Syntax ipv6 control-plane egress-filter Defaults Not enabled. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.
PAGE 801
ospfv3 Specify that this ACL is for OSPFv3 control plane traffic Defaults All access lists contain an implicit “deny any”; that is, if no match occurs, the packet is dropped. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.4(0.
PAGE 802
l2acl 1-4 ipv4acl 1- 4 ipv6acl 0-4 • L3 ACL (ipv4acl: 1 • IPv6 L3 ACL (ipv6acl): 2 Allocate space to support IPv6 ACLs. Enter all of the profiles and a range. Enter the CAM profile name then the amount to be allotted. The total space allocated must equal 4. The ipv6acl range must be a factor of 2. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 803
cam-acl Allocate space for IPv6 ACLs. Z9000 Syntax Parameters cam-acl {default | l2acl 1-10 ipv4acl 1-10 ipv6acl 0-10 ipv4qos 1-10 l2qos 1-10} default Use the default CAM profile settings, and set the CAM as follows: • • • • • l2acl 1-10 ipv4acl 1-10 ipv6acl 0-10 ipv4qos 1-10 l2qos 1-10 L3 ACL (ipv4acl): 6 L2 ACL(l2acl): 5 IPv6 L3 ACL (ipv6acl): 0 L3 QoS (ipv4qos): 1 L2 QoS (l2qos): 1 Allocate space to support IPv6 ACLs. Enter all of the profiles and a range.
PAGE 804
Ranges for the CAM profiles are from 1 to 10, except for the ipv6acl profile which is from 0 to 10. The ipv6acl allocation must be a factor of 2 (2, 4, 6, 8, 10).
PAGE 805
25 IPv6 Basics IPv6 basic commands are supported on the Dell Networking Z-Series platform. NOTE: For information about the Dell Networking operating software version and platform that supports IPv6 in each software feature, refer to the IPv6 Addressing chapter of the Dell Networking OS Configuration Guide. clear ipv6 fib Clear (refresh) all forwarding information base (FIB) entries on a linecard or stack unit.
PAGE 806
clear ipv6 route Clear (refresh) all or a specific route from the IPv6 routing table. Z9000 Syntax Parameters clear ipv6 route {* | ipv6-address prefix-length} * Enter the * to clear (refresh) all routes from the IPv6 routing table. ipv6-address prefix-length Enter the IPv6 address in the x:x:x:x::x format then the prefix length in the /x format. The range is from /0 to /128. NOTE: The :: notation specifies successive hexadecimal fields of zeros.
PAGE 807
The following is a list of the Dell Networking OS version history for this command. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. ipv6 address autoconfig Configure IPv6 address auto-configuration for the management interface. Syntax ipv6 address autoconfig To disable the address autoconfig operation on the management interface, use the no ipv6 address autoconfig command.
PAGE 808
• Removing auto-configuration removes all auto-configured IPv6 addresses and the link-local IPv6 address from that management interface. • IPv6 addresses on a single management interface cannot be members of the same subnet. • IPv6 secondary addresses on management interfaces across a platform must be members of the same subnet. • IPv6 secondary addresses on management interfaces should not match the virtual IP address and should not be in the same subnet as the virtual IP.
PAGE 809
Usage Information Example Version 7.8.1.0 Introduced on the C-Series and S-Series. Version 7.4.1.0 Introduced on the E-Series TeraScale. • If two addresses are configured, delete an existing address before configuring a new address. • If the last manually-configured global IPv6 address is removed using the “no” form of the command, the link-local IPv6 address is removed automatically. • IPv6 addresses on a single management interface cannot be members of the same subnet.
PAGE 810
Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.2) Introduced. Usage Information This command allows you to create an EUI64 address based on the specified prefix and MAC address only.
PAGE 811
Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. ipv6 flowlabel-zero Configure system to set the flow label field in the packets to zero. Z9000 Syntax ipv6 flowlabel-zero To disable the 0 from being set in the field and allow the rotocol operations to fill the field, use the no ipv6 flowlabel-zero command. Default Disabled Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 812
Parameters name Enter a text string to associate with one IP address. ipv6-address Enter the IPv6 address (X:X:X:X::X) to be mapped to the name. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.0.0 Introduced on the Z9000. Version 8.
PAGE 813
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.7.0 Introduced on the S4810. Version 8.4.2.1 Introduced on the C-Series and S-Series. Version 8.4.1.
PAGE 814
Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. ipv6 nd prefix Specify which IPv6 prefixes are included in Neighbor Advertisements. Z9000 Syntax Parameters Command Modes 814 ipv6 nd prefix {ipv6-prefix | prefix-length | default} [noadvertise] | [no-autoconfig] [no-rtr-address] [off-link] [lifetime {valid | infinite} {preferred | infinite}] ipv6-prefix Enter an IPv6 prefix. prefix-length Enter the prefix then the prefix length. The length range is from 0 to 128.
PAGE 815
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.2.0 Introduced on the E-Series TeraScale, C-Series, and S-Series.
PAGE 816
• For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a tunnel interface, enter the keyword tunnel then the tunnel interface number. The range is from 1 to 16383. • For a VLAN interface, enter the keyword VLAN then the vlan number. The range is from 1 to 4094.
PAGE 817
Usage Information Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.8.1.0 Introduced on the C-Series and S-Series. Version 7.4.1.0 Introduced on the E-Series TeraScale. When the interface goes down, Dell Networking OS withdraws the route. The route is re-installed, by Dell Networking OS, when the interface comes back up. When a recursive resolution is “broken,” Dell Networking OS withdraws the route.
PAGE 818
Defaults Enabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.7.0 Introduced on the S4810. Version 8.4.2.1 Introduced on the S-Series. Version 8.2.1.
PAGE 819
Parameters unit-number Enter the stack unit’s ID number. The range is from 0 to 11. port-set Enter the keyword Port Set. summary (OPTIONAL) Enter the keyword summary to display a table listing network prefixes and the total number prefixes which can be entered into the IPv6 CAM. index (OPTIONAL) Enter the index in the IPv6 CAM. ipv6-address Enter the IPv6 address in the x:x:x:x::x/n format to display networks that have more specific prefixes. The range is from /0 to /128.
PAGE 820
show ipv6 control-plane icmp Displays the status of the icmp control-plane setting for the error eate limit setting. Z9000 Syntax show ipv6 control-plane icmp Default 100 Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 8.3.19.0 Introduced on the S4820T.
PAGE 821
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.7.0 Introduced on the S4810. Version 8.4.2.1 Introduced on the S-Series. Host tables are not stored in CAM tables on S-Series platforms.
PAGE 822
show ipv6 interface Display the status of interfaces configured for IPv6.
PAGE 823
Defaults Command Modes Command History tunnel tunnelid (OPTIONAL) View information for a tunnel interface. vlan (OPTIONAL) View information for IPv6 VLANs. none • • EXEC EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2. (0.0) Added support for tunnel interface. Version 9.0.0.
PAGE 824
ND ND ND ND advertised reachable time is 0 advertised retransmit interval router advertisements are sent router advertisements live for milliseconds is 0 milliseconds every 200 to 600 seconds 1800 seconds Dell# Example (Managementet hernet) Dell# Dell#show ipv6 int man 0/0 ManagementEthernet 0/0 is up, line protocol is up IPV6 is enabled Link Local address: fe80::201:e8ff:fe8a:e8f7 Global Unicast address(es): Actual address is 600::1, subnet is 600::/64 Virtual-IP IPv6 address is not set Global Anycast
PAGE 825
MTU is 1500 ICMP redirects are not sent DAD is enabled: number of DAD attempts: 1 ND reachable time is 30 seconds ND advertised reachable time is 30 seconds ND advertised retransmit interval is 30 seconds ND router advertisements are sent every 200 seconds ND router advertisements live for 1800 seconds show ipv6 mld_host Display the IPv6 MLD host counters. Z9000 Syntax show ipv6 mld_host Command Modes EXEC Command History This guide is platform-specific.
PAGE 826
Example MLD Host Traffic Counters Elapsed time since counters cleared: 0028:33:52 Received Sent Valid MLD Packets 97962 18036 Reports 79962 18034 Leaves ---0 MLDv2 Queries 18000 ---MLDv1 Queries 0 ---Errors: Malformed Packets: 4510 show ipv6 route Displays the IPv6 routes.
PAGE 827
Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information IPv6 Basics Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced on the E-Series ExaScale.
PAGE 828
Field Description • Example (ESeries) + = summary routes Destination Identifies the route’s destination IPv6 address. Gateway Identifies whether the route is directly connected and on which interface the route is configured. Dist/Metric Identifies if the route has a specified distance or metric. Last Change Identifies when the route was last changed or configured.
PAGE 829
Example (Summary) Dell#show ipv6 route summary Route Source Active Routes Non-active Routes connected 5 0 static 0 0 Total 5 0 Total 5 active route(s) using 952 bytes trust ipv6-diffserv Allows the dynamic classification of IPv6 DSCP. Syntax trust ipv6-diffserv To remove the definition, use the no trust ipv6-diffserv command. Defaults none Command Modes CONFIGURATION-POLICY-MAP-IN Command History This guide is platform-specific.
PAGE 830
IPv6 Service Class Field Queue ID 101XXXXX 5 100XXXXX 4 011XXXXX 3 010XXXXX 2 001XXXXX 1 000XXXXX 0 IPv6 Basics
PAGE 831
Intermediate System to Intermediate System (IS-IS) 26 The intermediate system to intermediate system (IS-IS) protocol for IPv4 and IPv6 is supported on the Z9000 platform. IS-IS is an interior gateway protocol that uses a shortest-path-first algorithm. IS-IS facilitates the communication between open systems, supporting routers passing both IP and OSI traffic. A router is considered an intermediate system. Networks are partitioned into manageable routing domains, called areas.
PAGE 832
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 7.5.1.0 Introduced on the E-Series. To perform protocol-support consistency checks on hello packets, use this command. The adjacency-check is enabled by default. advertise Leak routes between levels (distribute IP prefixes between Level 1 and Level 2 and vice versa).
PAGE 833
Usage Information Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 7.5.1.0 Added IPv6 ISIS support. Version 6.3.1.0 Version 6.3.1.0 Introduced You cannot disable leaking from one level to another; however, you can regulate the rate flow from one level to another using an IP Prefix list. If you do not configure the IP Prefix list, all routes are leaked. You can find more information in IETF RFC 2966, Domain-wide Prefix Distribution with Two-Level IS-IS.
PAGE 834
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. To prevent the link state database from receiving incorrect routing information from unauthorized routers, use the area-password command on routers within an area. The configured password injects into Level 1 LSPs, CSNPs, and PSNPs. Related Commands • domain-password — allows you to set the authentication password for a routing domain.
PAGE 835
clear isis Restart the IS-IS process. All IS-IS data is cleared. Z9000 Syntax Parameters clear isis [tag] {* | database | traffic} tag (Optional) Enter an alphanumeric string to specify the IS-IS routing tag area. * Enter the keyword * to clear all IS-IS information and restart the IS-IS process. This command removes IS-IS neighbor information and IS-IS LSP database information and the full SPF calculation is done. database Clears IS-IS LSP database information. traffic Clears IS-IS counters.
PAGE 836
nsap Enter a specific NSAP address that is associated with the name parameter. Defaults Not configured. Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.
PAGE 837
Usage Information Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Entering debug isis enables all debugging parameters. To display all debugging information in one output, use this command. To turn off debugging, you normally enter separate no forms of each command. To disable all debug messages for IS-IS at once, enter the no debug isis command.
PAGE 838
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. debug isis local-updates To debug IS-IS local update packets, enable debugging on a specific interface and provides diagnostic information. Z9000 Syntax debug isis local-updates [interface] To turn off debugging, use the no debug isis local-updates [interface] command.
PAGE 839
Version 8.3.12.0 Introduced on the S4810. Version 6.3.1.0 Introduced. debug isis snp-packets To debug IS-IS complete sequence number PDU (CSNP) and partial sequence number PDU (PSNP) packets, enable debugging on a specific interface and provides diagnostic information. Z9000 Syntax debug isis snp-packets [interface] To turn off debugging, use the no debug isis snp-packets [interface] command.
PAGE 840
Version 6.3.1.0 Introduced. debug isis spf-triggers Enable debugging on the events that triggered IS-IS shortest path first (SPF) events for debugging purposes. Z9000 Syntax debug isis spf-triggers To turn off debugging, use the no debug isis spf-triggers command. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 841
• For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a Gigabit Ethernet interface, enter the keyword GigabitEthernet the slot/port information. • For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a VLAN, enter the keyword vlan then a number from 1 to 4094.
PAGE 842
route-map map-name (OPTIONAL) A default route the routing process generates if the route map is satisfied. Defaults Not configured. Command Modes • ROUTER ISIS (for IPv4) • CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (for IPv6) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 843
description Enter a description of the IS-IS routing protocol. Z9000 Syntax description {description} To remove the description, use the no description {description} command. Parameters description Defaults none Command Modes ROUTER ISIS Command History Related Commands Enter a description to identify the IS-IS protocol (80 characters maximum). Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.
PAGE 844
ip-address mask (OPTIONAL) Enter an IP address in dotted decimal format and enter a mask in either dotted decimal or /prefix format. prefix-list (OPTIONAL) Enter the name of a prefix list name. Defaults weight = 115 Command Modes • ROUTER ISIS (for IPv4) • CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (for IPv6) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 845
• For a 1- Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a SONET interface, enter the keyword sonet then the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a VLAN, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured.
PAGE 846
To return to the default values, use the no distribute-list prefix-listname out [bgp as number connected | ospf process-id | rip | static] command. Parameters prefix-listname Specify the prefix list to filter prefixes in routing updates. connected (OPTIONAL) Enter the keyword connected for directly connected routing process. ospf process-id (OPTIONAL) Enter the keyword ospf then the OSPF process-ID number. The range is from 1 to 65535. bgp as number (OPTIONAL) Enter the BGP then the AS Number.
PAGE 847
distribute-list redistributed-override Suppress flapping of routes when the same route is redistributed into IS-IS from multiple routers in the network. Z9000 Syntax distribute-list redistributed-override in To return to the default, use the no distribute-list redistributedoverride in command. Defaults none Command Modes • ROUTER ISIS (for IPv4) • CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (for IPv6) Command History This guide is platform-specific.
PAGE 848
Parameters hmac-md5 (OPTIONAL) Enter the keywords hmac-md5 to encrypt the password using MD5. encryptiontype (OPTIONAL) Enter 7 to encrypt the password using DES. password Enter an alphanumeric string up to 16 characters long. If you do not specify an encryption type or hmac-md5 keywords, the password is processed as plain text which provides limited security. Defaults No default password. Command Modes ROUTER ISIS Command History This guide is platform-specific.
PAGE 849
Parameters ietf Enter ietf to enable graceful restart on the IS-IS router. Defaults Graceful restart disabled. Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T.
PAGE 850
Defaults 5 minutes Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.1.
PAGE 851
Related Commands Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.1.0 Introduced on the E-Series. graceful-restart t3 — configures the overall wait time before graceful restart completes. graceful-restart t1 Set the graceful restart wait time before unacknowledged restart requests are generated.
PAGE 852
Version 8.3.11.1 Introduced on the Z9000. Version 8.3.1.0 Introduced on the E-Series. graceful-restart t2 Configure the wait time for the graceful restart timer T2 that a restarting router uses as the wait time for each database to synchronize. Z9000 Syntax graceful-restart t2 {level-1 | level-2} seconds To return to the default, use the no graceful-restart t2 command.
PAGE 853
graceful-restart t3 Configure the overall wait time before graceful restart completes. Z9000 Syntax graceful-restart t3 {adjacency | manual} seconds To return to the default, use the no graceful-restart t3 command. Parameters adjacency Enter the keyword adjacency so that the restarting router receives the remaining time value from its peer and adjusts its T3 value so if you have configured this option. manual Enter the keyword manual to specify a time value that the restarting router uses.
PAGE 854
Related Commands graceful-restart restart-wait — enables the graceful restart maximum wait time before a restarting peer comes up. hello padding Use to turn ON or OFF padding for LAN and point-to-point hello PDUs or to selectively turn padding ON or OFF for LAN or point-to-point hello PDUs. Z9000 Syntax hello padding [multi-point | point-to-point] To return to the default, use the no hello padding [multi-point | pointto-point] command.
PAGE 855
hostname dynamic Enables dynamic learning of hostnames from routers in the domain and allows the routers to advertise the hostname in LSPs. Z9000 Syntax hostname dynamic To disable this command, use the no hostname dynamic command. Defaults Enabled. Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 856
Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000.
PAGE 857
Usage Information Related Commands Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 7.5.1.0 Introduced. To assign a network entity title to enable IS-IS, use the net command. • net — configures an IS-IS network entity title (NET) for the routing process. • router isis — enables the IS-IS routing protocol. ipv6 router isis Enable the IPv6 IS-IS routing protocol and specify an IPv6 IS-IS process.
PAGE 858
Usage Information Version 8.3.11.1 Introduced on the Z9000. Version 7.5.1.0 Introduced on the E-Series. Configure a network entity title (the net command) to specify the area address and the router system ID. To establish adjacencies and establish dynamic routing, enable routing on one or more interfaces. You can configure only one IS-IS routing process to perform Level 2 routing. A level-1-2 designation performs Level 1 and Level 2 routing at the same time.
PAGE 859
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Because the default establishes Level 1 and Level 2 adjacencies, you do not need to configure this command. Routers in an IS-IS system must be configured as a Level 1-only, Level 1-2, or Level 2-only system.
PAGE 860
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. The default values of this command are typically satisfactory transmission times for a specific interface on a designated intermediate system. To maintain database synchronization, the designated routers send CSNPs. You can configure Level 1 and Level 2 CSNP intervals independently.
PAGE 861
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Usage Information Hello packets are held for a length of three times the value of the hello interval. To conserve bandwidth and CPU usage, use a high hello interval seconds. Use a low hello interval seconds for faster convergence (but uses more bandwidth and CPU resources).
PAGE 862
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Usage Information The holdtime (the product of the hello-multiplier multiplied by the hello-interval) determines how long a neighbor waits for a hello packet before declaring the neighbor is down so routes can be recalculated. Related Commands isis hello-interval — specifies the length of time between hello packets.
PAGE 863
Related Commands hello padding — turns ON or OFF padding for LAN and point-to-point hello PDUs. isis ipv6 metric Assign metric to an interface for use with IPv6 information. Z9000 Syntax isis ipv6 metric default-metric [level-1 | level-2] To return to the default values, use the no ipv6 isis metric [defaultmetric] [level-1 | level-2] command. Parameters default-metric Metric assigned to the link and used to calculate the cost from each other router via the links in the network to other destinations.
PAGE 864
Usage Information Dell Networking recommends configuring metrics on all interfaces. Without configuring this command, the IS-IS metrics are similar to hop-count metrics. isis metric Assign a metric to an interface. Z9000 Syntax isis metric default-metric [level-1 | level-2] To return to the default values, use the no isis metric [default-metric] [level-1 | level-2] command.
PAGE 865
Usage Information Dell Networking recommends configuring metrics on all interfaces. Without configuring this command, the IS-IS metrics are similar to hop-count metrics. isis network point-to-point Enable the software to treat a broadcast interface as a point-to-point interface. Z9000 Syntax isis network point-to-point To disable the feature, use the no isis network point-to-point command. Defaults Not enabled. Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 866
Parameters encryptiontype (OPTIONAL) Enter 7 to encrypt the password using DES. hmac-md5 (OPTIONAL) Enter the keywords hmac-md5 to encrypt the password using MD5. password Assign the interface authentication password. level-1 (OPTIONAL) Independently configures the authentication password for Level 1. The router acts as a station router for Level 1 routing. This setting is the default. level-2 (OPTIONAL) Independently configures the authentication password for Level 2.
PAGE 867
isis priority Set the priority of the designated router you select. Z9000 Syntax isis priority value [level-1 | level-2] To return to the default values, use the no isis priority [value] [level-1 | level-2] command. Parameters value This value sets the router priority. The higher the value, the higher the priority. The range is from 0 to 127. The default is 64. level-1 (OPTIONAL) Specify the priority for Level 1. This setting is the default. level-2 (OPTIONAL) Specify the priority for Level 2.
PAGE 868
is-type Configure IS-IS operating level for a router. Z9000 Syntax is-type {level-1 | level-1-2 | level-2-only} To return to the default values, use the no is-type command. Parameters level-1 Allows a router to act as a Level 1 router. level-1-2 Allows a router to act as both a Level 1 and Level 2 router. This setting is the default. level-2-only Allows a router to act as a Level 2 router. Defaults level-1-2 Command Modes ROUTER ISIS Command History This guide is platform-specific.
PAGE 869
log-adjacency-changes Generate a log messages for adjacency state changes. Z9000 Syntax log-adjacency-changes To disable this function, use the no log-adjacency-changes command. Defaults Adjacency changes are not logged. Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 870
level-2 (OPTIONAL) Enter the keywords level-2 to apply the configuration to generation of Level-2 LSPs. interval seconds Enter the maximum number of seconds between LSP generations. The range is from 0 to 120 seconds. The default is 5 seconds. initial_wait_inte rval seconds (OPTIONAL) Enter the initial wait time, in seconds, before running the first LSP generation. The range is from 0 to 120 seconds. The default is 1 second.
PAGE 871
lsp-mtu Set the maximum transmission unit (MTU) of IS-IS link-state packets (LSPs). This command only limits the size of LSPs this router generates. Z9000 Syntax lsp-mtu size To return to the default values, use the no lsp-mtu command. Parameters size The maximum LSP size, in bytes. The range is from 128 to 1497 for Non-Jumbo mode and from 128 to 9195 for Jumbo mode. The default is 1497. Defaults 1497 bytes. Command Modes ROUTER ISIS Command History This guide is platform-specific.
PAGE 872
lsp-refresh-interval Set the link state PDU (LSP) refresh interval. LSPs must be refreshed before they expire. When the LSPs are not refreshed after a refresh interval, they are kept in a database until their max-lsp-lifetime reaches zero and then LSPs is purged. Z9000 Syntax lsp-refresh-interval seconds To restore the default refresh interval, use the no lsp-refresh-interval command. Parameters seconds The LSP refresh interval, in seconds.
PAGE 873
max-area-addresses Configure manual area addresses. Z9000 Syntax max-area-addresses number To return to the default values, use the no max-area-addresses command. Parameters number Set the maximum number of manual area addresses. The range is from 3 to 6. The default is 3. Defaults 3 addresses Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 874
Parameters seconds The maximum lifetime of LSP in seconds. This value must be greater than the lsp-refresh-interval command. The higher the value the longer the LSPs are kept. The range is from 1 to 65535. The default is 1200. Defaults 1200 seconds Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 875
Defaults Command Modes Command History 4 • ROUTER ISIS (for IPv4) • CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (for IPv6) This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.
PAGE 876
Defaults narrow; if no Level is specified, Level-1 and Level-2 are configured. Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000.
PAGE 877
The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.12.0 Introduced on the S4810. Version 7.8.1.0 Introduced. net To configure an IS-IS network entity title (NET) for a routing process, use this mandatory command. If you did not configure a NET, the IS-IS process does not start.
PAGE 878
passive-interface Suppress routing updates on an interface. This command stops the router from sending updates on that interface. Z9000 Syntax passive-interface interface To delete a passive interface configuration, use the no passive-interface interface command. Parameters interface Enter the following keywords and slot/port or number information: • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
PAGE 879
redistribute Redistribute routes from one routing domain to another routing domain. Z9000 Syntax redistribute {static | connected | rip} [level-1 | level-1-2 | level-2] [metric metric-value] [metric-type {external | internal}] [route-map map-name] To end redistribution or disable any of the specified keywords, use the no redistribute {static | connected | rip} [metric metric-value] [metric-type {external | internal}] [level-1 | level-1-2 | level-2] [route-map map-name] command.
PAGE 880
• Command History CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (for IPv6) This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.12.0 Introduced on the S4810.
PAGE 881
redistribute bgp Redistribute routing information from a BGP process. Z9000 Syntax redistribute bgp AS number [level-1| level-1-2 | level-2] [metric metric-value] [metric-type {external| internal}] [route-map map-name] To return to the default values, use the no redistribute bgp command with the appropriate parameters. Parameters AS number Enter a number that corresponds to the autonomous system number. The range is from 1 to 65355.
PAGE 882
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.12.0 Introduced on the S4810. Version 7.5.1.0 Added support for IPv6 ISIS. Version 6.3.1.0 Introduced. Usage Information BGP to IS-IS redistribution supports “match” options using route maps. You can set the metric value, level, and metric-type of redistributed routes by the redistribution command. You can “set” more advanced options using route maps.
PAGE 883
metric-type {external | internal} (OPTIONAL) The external link type associated with the default route advertised into a routing domain. The two options are: • external • internal level-1 (OPTIONAL) Routes are independently redistributed into ISIS as Level 1 routes. level-1-2 (OPTIONAL) Routes are independently redistributed into ISIS as Level-1-2 routes. level-2 (OPTIONAL) Routes are independently redistributed into ISIS as Level 2 routes. This setting is the default.
PAGE 884
Usage Information How a metric value assigned to a redistributed route is advertised depends on how on the configuration of the metric-style command. If the metric-style command is set for Narrow mode and the metric value in the redistribute ospf command is set to a number higher than 63, the metric value advertised in LSPs is 63. If the metric-style command is set for wide mode, the metric value in the redistribute ospf command is advertised.
PAGE 885
You can configure only one IS-IS routing process to perform Level 2 routing. A level-1-2 designation performs Level 1 and Level 2 routing at the same time. Related Commands • ip router isis — configures IS-IS routing processes for IP on interfaces and attaches an area designator to the routing process. • net — configures an IS-IS network entity title (NET) for a routing process. • is-type — assigns a type for a given area.
PAGE 886
show config Display the changes you made to the IS-IS configuration. Default values are not shown. Z9000 Syntax show config Command Modes • ROUTER ISIS (for IPv4) • CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (for IPv6) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 887
show isis database Display the IS-IS link state database. Z9000 Syntax Parameters show isis database [level-1 | level-2] [local] [detail | summary] [lspid] level-1 (OPTIONAL) Displays the Level 1 IS-IS link-state database. level-2 (OPTIONAL) Displays the Level 2 IS-IS link-state database. local (OPTIONAL) Displays local link-state database information. detail (OPTIONAL) Detailed link-state database information of each LSP displays when specified. If not specified, a summary displays.
PAGE 888
Field Description The first six octets are the System ID of the originating router. The first six octets are the System ID of the originating router. The next octet is the pseudonode ID. If this byte is not zero, the LSP describes system links. If this byte is zero (0), the LSP describes the state of the originating router. The designated router for a LAN creates and floods a pseudonode LSP and describes the attached systems. The last octet is the LSP number.
PAGE 889
ISIS.00-00 * 0x00000006 0xCF43 580 ! FTOS#show isis database detail ISIS.00-00 0/0/0 IS-IS Level-1 Link State Database LSPID LSP Seq Num LSP Checksum LSP Holdtime ATT/P/OL ISIS.00-00 * 0x0000002B 0x853B 1075 0/0/0 Area Address: 49.0000.0001 NLPID: 0xCC 0x8E IP Address: 10.1.1.1 IPv6 Address: 1011::1 Topology: IPv4 (0x00) IPv6 (0x8002) Metric: 10 IS OSPF.00 Metric: 10 IS (MT-IPv6) OSPF.00 Metric: 10 IP 15.1.1.0 255.255.255.
PAGE 890
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.1.0 Introduced on the E-Series.
PAGE 891
The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. FTOS#show isis hostname System Id Dynamic Name Static Name *F100.E120.0013 Force10 ISIS FTOS# show isis interface Display detailed IS-IS interface status and configuration information.
PAGE 892
Example Version 9.2(0.2) Introduced on the Z9000. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. FTOSF>show isis int GigabitEthernet 0/7 is up, line protocol is up MTU 1497, Encapsulation SAP Routing Protocol: IS-IS Circuit Type: Level-1-2 Interface Index 37847070, Local circuit ID 1 Level-1 Metric: 10, Priority: 64, Circuit ID: systest-3.
PAGE 893
• For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a VLAN, enter the keyword vlan then a number from 1 to 4094. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific.
PAGE 894
Example Field Description Circuit Id The neighbor’s interpretation of the designated router for the interface. The bold sections below identify that Multi-Topology IS-IS is enabled. FTOS#show isis neighbors System Id Interface State Type Priority Uptime Circuit Id TEST Gi 7/1 Up L1L2(M) 127 09:28:01 TEST.02 ! FTOS#show isis neighbors detail System Id Interface State Type Priority Uptime Circuit Id TEST Gi 7/1 Up L1L2(M) 127 09:28:04 TEST.02 Area Address(es): 49.0000.0001 IP Address(es): 25.1.1.
PAGE 895
System Id: F100.E120.0013 IS-Type: level-1-2 Manual area address(es): 49.0000.0001 Routing for area address(es): 49.0000.0001 Interfaces supported by IS-IS: GigabitEthernet 1/0 - IP - IPv6 GigabitEthernet 1/1 - IP - IPv6 GigabitEthernet 1/10 - IP - IPv6 Loopback 0 - IP - IPv6 Redistributing: Distance: 115 Generate narrow metrics: level-1-2 Accept narrow metrics: level-1-2 Generate wide metrics: none Accept wide metrics: none Multi Topology Routing is enabled in transition mode.
PAGE 896
Usage Information Example 896 Version 9.2(0.2) Introduced on the Z9000. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. The following describes the show isis traffic command shown in the following example. Item Description Level-1/Level-2 Hellos (sent/rcvd) Displays the number of Hello packets sent and received. PTP Hellos (sent/ rcvd) Displays the number of point-to-point Hellos sent and received.
PAGE 897
IS-IS: IS-IS: IS-IS: IS-IS: IS-IS: IS-IS: IS-IS: IS-IS: IS-IS: FTOS# Level-2 LSPs CSNPs (sent/rcvd) : 472/238 Level-1 LSPs PSNPs (sent/rcvd) : 0/0 Level-2 LSPs PSNPs (sent/rcvd) : 10/337 Level-1 DR Elections : 4 Level-2 DR Elections : 4 Level-1 SPF Calculations : 0 Level-2 SPF Calculations : 389 LSP checksum errors received : 0 LSP authentication failures : 0 spf-interval Specify the minimum interval between shortest path first (SPF) calculations.
PAGE 898
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.12.0 Introduced on the S4810. Version 7.8.1.0 Added support for multi-topology ISIS. Version 7.5.1.0 Added support for SPF Throttling Enhancement. This command spf-interval in CONFIG-ROUTER-ISIS-AF-IPV6 mode is used for IPv6 Multi-Topology route computation only.
PAGE 899
27 Link Aggregation Control Protocol (LACP) This chapter contains commands for Dell Networks’s implementation of the link aggregation control protocol (LACP) for creating dynamic link aggregation groups (LAGs) — known as “port-channels” in the Dell Networking operating software. The LACP commands in this chapter are supported by Dell Networking OS on the Z9000 platform.
PAGE 900
Version 6.2.1.1 Related Commands Introduced on the E-Series. show lacp — displays the LACP configuration. debug lacp Debug LACP (configuration, events, and so on). Z9000 Syntax debug lacp [config | events | pdu [interface-type [in | out]]] To disable LACP debugging, use the no [config | events | pdu [interface-type [in | out]]] command. Parameters config (OPTIONAL) Enter the keyword config to debug the LACP configuration.
PAGE 901
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.2.1.1 Introduced on the E-Series. lacp long-timeout Configure a long timeout period (30 seconds) for an LACP session.
PAGE 902
Related Commands show lacp — displays the LACP configuration. lacp port-priority To influence which ports will be put in Standby mode when there is a hardware limitation that prevents all compatible ports from aggregating, configure the port priority. Z-Series Syntax lacp port-priority priority-value To return to the default setting, use the no lacp port-priority priorityvalue command. Parameters priority-value Enter the port-priority value. The higher the value number, the lower the priority.
PAGE 903
lacp system-priority Configure the LACP system priority. Z-Series Syntax Parameters lacp system-priority priority-value priority-value Enter the port-priority value. The higher the value number, the lower the priority. The range is from 1 to 65535. The default is 32768. Defaults 32768 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 904
NOTE: LACP modes are defined in Usage Information. passive Enter the keyword passive to set the mode to the passive state. NOTE: LACP modes are defined in Usage Information. off Enter the keyword off to set the mode to the off state. NOTE: LACP modes are defined in Usage Information. Defaults off Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 905
port-channel-protocol lacp Enable LACP on any LAN port. Z9000 Syntax port-channel-protocol lacp To disable LACP on a LAN port, use the no port-channel-protocol lacp command. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.
PAGE 906
Defaults Command Modes Command History Without a Port Channel specified, the command clears all Port Channel counters. • • EXEC EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example (PortChannelNumber) Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.
PAGE 907
----------------------------------------------------Gi 10/6 200 200 0 0 0 0 Dell# Related Commands clear lacp counters — clears the LACP counters. show interfaces port-channel — displays information on configured Port Channel groups. hg-link-bundle-monitor Enable the capability to examine the utilization and traffic distribution of high-Gigabit port channels. This command is supported on the Z9000 platform.
PAGE 908
hg-link-bundle-monitor trigger-threshold Specify the threshold value for high-Gigabit Ethernet port channels or trunk groups, which is a checkpoint exceeding which the link bundle is marked as being overutilized and alarm is generated. This command is supported on the Z9000 platform. Syntax hg-link-bundle-monitor trigger-threshold <1-90> To restore the default value, use the no version of this command.. Parameters <1-90> Command Modes CONFIGURATION Command History Version 9.3(0.
PAGE 909
Usage Information This interval cannot be configured per high-Gigabit port channel and is applicable for all of the high-Gigabit port channels on the system. show hg-link-bundle-distribution Display the traffic-handling and utilization of the member interfaces of the high-Gigabit port channel or trunk group. This command is supported on the Z9000 platform.
PAGE 910
Field Description port channel occurred.
PAGE 911
show hardware stack-unit (for high-Gigabit Ethernet ports) Display the data plane or management plane input and output statistics of the high-Gigabit Ethernet or backplane port of the designated stack unit or Z9000 unit. NOTE: Only the parameters that are newly introduced with this command in Release 9.3(0.0) are explained here. For a complete description of all of the options that are available with this command, refer the relevant Command Reference Guide of the applicable platform of Release 9.2(0.0).
PAGE 912
Output Statistics: 1335309 packets, 187184751 bytes, 0 underruns 0 64-byte pkts, 665971 over 64-byte pkts, 586727 over 127byte pkts 82038 over 255-byte pkts, 58 over 511-byte pkts, 515 over 1023-byte pkts 408949 Multicasts, 0 Broadcasts, 926163 Unicasts 0 throttles, 0 discarded, 0 collisions, 0 wredDrops Rate info (interval 30 seconds): Input 00.08 Mbits/sec, 10 packets/sec, 0.00% of line-rate Output 00.00 Mbits/sec, 3 packets/sec, 0.
PAGE 913
Defaults none Command Modes EXEC Privilege Command History Related Commands Version 9.3(0.0) Added support for the hg-stats option on the Z9000 platform. show hardware stack-unit — displays the data plane or management plane input and output statistics of the designated component of the designated stack member.
PAGE 914
PAGE 915
28 Layer 2 This chapter describes commands to configure Layer 2 features. This chapter contains the following sections: • MAC Addressing Commands • Virtual LAN (VLAN) Commands • The VLAN commands are supported on all the Z9000 platform. MAC Addressing Commands The following commands are related to configuring, managing, and viewing MAC addresses. clear mac-address-table Clear the MAC address table of all MAC address learned dynamically.
PAGE 916
vlan vlan-id Enter the keyword vlan then a VLAN ID number from 1 to 4094. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Added support for sticky MAC addresses.
PAGE 917
Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 On the E-Series, available in INTERFACE VLAN context, reduced the minimum aging time in the INTERFACE VLAN context from 10 seconds to 1 second. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series.
PAGE 918
output-range interface vlan vlan-id For a multicast MAC address, enter the keyword outputrange then one of the following interfaces to indicate a range of ports for which traffic is forwarded: • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128.
PAGE 919
mac-address-table station-move threshold Change the frequency with which the MAC address station-move trap is sent after a MAC address changes in a VLAN. A trap is sent if a station move is detected above a threshold number of times in a given interval. Syntax Parameters [no] mac-address-table station-move threshold number interval count threshold number Enter the keyword threshold then the number of times MAC addresses in VLANs can change before an SNMP trap is sent. The range is from 1 to 10.
PAGE 920
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Introduced on the S-Series. Version 7.6.1.
PAGE 921
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.12.
PAGE 922
this occurs, un-configure the existing configuration first and then reapply the limit with a lower value. Related Commands mac learning-limit mac-address-sticky — Replaces deprecated no-station-move parameter. show mac learning-limit — displays MAC learning-limit configuration. mac learning-limit learn-limit-violation Configure an action for a MAC address learning-limit violation.
PAGE 923
Related Commands show mac learning-limit — displays details of the mac learning-limit. mac learning-limit mac-address-sticky Maintain the dynamically learned mac addresses as sticky MAC addresses on the selected port. Z-Series Syntax mac learning-limit mac-address-sticky To convert the sticky MAC addresses to dynamic MAC addresses, use the no mac learning-limit command. Parameters mac-addresssticky Configures the dynamic MAC addresses as sticky on an interface.
PAGE 924
To disable a configuration, use the no mac learning-limit station-moveviolation command, then the configured keyword. Parameters log Enter the keyword log to generate a syslog message on a station move violation. shutdown-both Enter the keyword shutdown to shut down both the original and offending interface and generate a syslog message. shutdownoffending Enter the keywords shutdown-offending to shut down the offending interface and generate a syslog message.
PAGE 925
Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.
PAGE 926
• vlan vlan-id For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. (OPTIONAL) Enter the keyword vlan then the VLAN ID to display the MAC address assigned to the VLAN. The range is from 1 to 4094. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 927
• For a Port Channel interface, enter the keywords portchannel then a number. • For a SONET interface, enter the keyword sonet then the slot/ port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. static (OPTIONAL) Enter the keyword static to display only those MAC addresses specifically configured on the switch.
PAGE 928
112 113 114 115 116 117 Dell# 0 0 0 0 0 0 0 0 0 0 0 0 00:01:e8:0d:b7:62 00:01:e8:0d:b7:61 00:01:e8:0d:b7:60 00:01:e8:0d:b7:5f 00:01:e8:0d:b7:5e 00:01:e8:0d:b7:5d SYSTEM_STATIC SYSTEM_STATIC SYSTEM_STATIC SYSTEM_STATIC SYSTEM_STATIC SYSTEM_STATIC DROP DROP DROP DROP DROP DROP show mac-address-table Display the MAC address table.
PAGE 929
count (OPTIONAL) Enter the keyword count, then optionally, by an interface or VLAN ID, to display total or interface-specific static addresses, dynamic addresses, and MAC addresses in use. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 930
Column Heading Description • State Example Usage Information te — 10 Gigabit Ethernet then a slot/port. Lists if the MAC address is in use (Active) or not in use (Inactive).
PAGE 931
Line Beginning With Description Static Address... Lists the number of user-defined MAC addresses. Total MAC... Lists the total number of MAC addresses the switch uses. Example (Count) Dell# show mac-address-table count MAC Entries for all vlans : Dynamic Address Count : 110 Static Address (User-defined) Count : 0 Sticky Address Count : 0 Total Synced Mac from Peer(N): 100 Total MAC Addresses in Use: 110 Dell# Related Commands show mac-address-table aging-time — displays MAC aging time.
PAGE 932
Example Dell#show mac-address-table aging-time Mac-address-table aging time : 1800 Dell# Related Commands show mac-address-table — displays the current MAC address configuration. show mac accounting destination Display destination counters for Layer 2 traffic (available on physical interfaces only).
PAGE 933
Usage Information MAC Accounting information can be accessed using SNMP via the Force10 Monitor MIB. For more information about enabling SNMP, refer to the Dell Networking OS Configuration Guide. NOTE: Currently, the Force10 MONITOR MIB does not return the MAC addresses in an increasing order using SNMP. As a workaround, you can use the -C c option in snmpwalk or snmpbulkwalk to access the Force10 MONITOR MIB. For example: % snmpwalk -C c -v 2c -c public 133.33.33.131 enterprise.6027.3.3.
PAGE 934
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.3.7.0 Introduced on the S4810.
PAGE 935
default vlan-id Specify a VLAN as the Default VLAN. Z9000 Syntax default vlan-id vlan-id To remove the default VLAN status from a VLAN and VLAN 1 does not exist, use the no default vlan-id vlan-id syntax. Parameters vlan-id Enter the VLAN ID number of the VLAN to become the new Default VLAN. The range is from 1 to 4094. The default is 1. Defaults The Default VLAN is VLAN 1. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 936
default-vlan disable Disable the default VLAN so that all switchports are placed in the Null VLAN until they are explicitly configured as a member of another VLAN. Z9000 Defaults Enabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.
PAGE 937
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. Usage Information To display information about a named VLAN, enter the show vlan command with the name parameter or the show interfaces description command.
PAGE 938
no ip address no shutdown Dell(conf-if-vl-100)# show vlan Display the current VLAN configurations on the switch. Z9000 Syntax Parameters show vlan [brief | id vlan-id | name vlan-name] brief (OPTIONAL) Enter the keyword brief to display the following information: • VLAN ID • VLAN name (left blank if none is configured) • Spanning Tree Group ID • MAC address aging time • IP address id vlan-id (OPTIONAL) Enter the keyword id then a number from 1 to 4094.
PAGE 939
Usage Information Version 7.6.1.0 Introduced on the S-Series and revised the output to display Native VLAN. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. The following describes the show vlan command shown in the following example. Column Heading Description (Column 1 — no heading) • asterisk symbol (*) = Default VLAN • G = GVRP VLAN • P = primary VLAN C = community VLAN I = isolated VLAN • O = OpenFlow NUM Displays existing VLAN IDs.
PAGE 940
Q: U - Untagged, T - Tagged, O - Openflow x - Dot1x untagged, X - Dot1x tagged o - OpenFlow untagged, O - OpenFlow tagged G - GVRP tagged, M - Vlan-stack i - Internal untagged, I - Internal tagged, v - VLT untagged, V - VLT tagged NUM Status Description Q Ports * 1 Inactive 2 Active U Po1(Gi 13/0) T Po20(Gi 13/6), Gi 13/25 T Gi 13/7 3 Active T Po20(Gi 13/6) T Gi 13/7 U Gi 13/1 4 Active U Po2(Gi 13/2) T Po20(Gi 13/6) T Gi 13/7 5 Active T Po20(Gi 13/6) T Gi 13/7 U Gi 13/3 6 Active U Po3(Gi 13/4) T Po20(Gi 13/
PAGE 941
Example (Brief) Dell#show vlan br VLAN Name STG MAC Aging IP Address ---- -----------------------------------1 0 1800 unassigned 2 0 1800 2.2.2.2/24 3 0 1800 3.3.3.
PAGE 942
Defaults All interfaces in Layer 2 mode are untagged. Command Modes INTERFACE VLAN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.5.1.
PAGE 943
• For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. Defaults Not configured. Command Modes INTERFACE VLAN Command History This guide is platform-specific.
PAGE 944
untagged Add a Layer 2 interface to a VLAN as an untagged interface. Z9000 Syntax untagged interface To remove an untagged interface from a VLAN, use the no untagged interface command. Parameters interface Enter the following keywords and slot/port or number information: • • • For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 945
Related Commands interface vlan — configures a VLAN. tagged — specifies which interfaces in a VLAN are tagged. Far-End Failure Detection (FEFD) The Dell Networking operating software supports far-end failure detection (FEFD) on the Ethernet interfaces of the Z9000 platform. The FEFD feature detects and reports far-end link failures. • FEFD is not supported on the Management interface. • During an RPM failover, FEFD is operationally disabled for approximately 8 to 10 seconds.
PAGE 946
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.12.0 Introduced on the S4810. Legacy ESeries command. Related Commands • fefd — enables far-end failure detection on an interface. • fefd reset — enables FEFD globally on the system. fefd Enable Far-End Failure Detection on an interface, set the FEFD interval, or select the FEFD mode.
PAGE 947
Usage Information Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.12.0 Introduced on the S4810. When you enter no fefd for an interface and fefd-global, FEFD is enabled on the interface because the no fefd command is not retained in the configuration file. To keep the interface FEFD disabled when the global configuration changes, use the fefd reset command.
PAGE 948
Related Commands • fefd reset — enables FEFD globally on the system. • fefd mode — changes FEFD mode on an interface. fefd interval Set an interval between control packets. Z9000 Syntax fefd interval seconds To return to the default value, use the no fefd interval command. Parameters seconds Enter a number as the time between FEFD control packets. The range is from 3 to 300 seconds. The default is 15 seconds.
PAGE 949
Parameters normal (OPTIONAL) Enter the keyword normal to change the link state to “unknown” when a far-end failure the software detects on that interface. When the interface is placed in “unknown” state, the software brings down the line protocol. aggressive (OPTIONAL) Enter the keyword aggressive to change the link state to “error-disabled” when a far-end failure the software detects on that interface.
PAGE 950
Defaults Not configured. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.12.0 Introduced on the S4810. Legacy ESeries command.
PAGE 951
Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Legacy ESeries command. Related Commands • fefd — enables far-end failure detection. • fefd-global — enables FEFD globally on the system. fefd-global Enable FEFD globally on the system. Z9000 Syntax fefd-global [interval seconds][mode {normal | aggressive}] To disable FEFD globally, use the no fefd-global [mode {normal | aggressive}] command.
PAGE 952
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.12.0 Introduced on the S4810. Legacy ESeries command. Usage Information If you enter only the fefd-global syntax, the mode is normal and the default interval is 15 seconds. If you disable FEFD globally (no fefd-global), the system does not remove the FEFD interface configuration. Related Commands • fefd — enables far-end failure detection.
PAGE 953
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.12.0 Introduced on the S4810. Legacy ESeries command. Usage Information Example The following describes the show fefd command shown in the following example. Field Description Interface Displays the interfaces type and number. Mode Displays the mode (aggressive or normal) or NA if the interface contains fefd reset in its configuration. Interval Displays the interval between FEFD packets.
PAGE 954
Related Commands 954 • fefd — enables far-end failure detection. • fefd disable — disables FEFD on an interface only. • fefd-global — enables FEFD globally on the system. • fefd reset — resets all interfaces or a single interface that was in “error-disabled” mode.
PAGE 955
Link Layer Discovery Protocol (LLDP) 29 The link layer discovery protocol (LLDP) advertises connectivity and management from the local station to the adjacent stations on an IEEE 802 LAN. This chapter contains the following sections: • LLPD Commands • LLDP-MED Commands LLDP facilitates multi-vendor interoperability by using standard management tools to discover and make available a physical topology for network management.
PAGE 956
vlan-name Enter the keywords vlan-name to advertise the vlan-name TLV. This keyword is only supported on the C-Series and SSeries. Defaults Disabled. Command Modes CONFIGURATION (conf-lldp) and INTERFACE (conf-if-interface-lldp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 957
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Introduced on the S-Series. Version 7.6.1.
PAGE 958
Usage Information Version 9.1. (0.0) Modified to support management-address parameter. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Introduced on the S-Series. Version 7.6.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced on the E-Series. The command options management-address,system-capabilities, systemdescription, and system-name can be invoked individually or together, in any sequence.
PAGE 959
Version 9.1. (0.0) Introduced on the Z9000 and S4810. Version 8.3.19.0 Introduced on the S4820T. clear lldp counters Clear LLDP transmitting and receiving counters for all physical interfaces or a specific physical interface. Z9000 Syntax Parameters clear lldp counters interface interface Enter the following keywords and slot/port or number information: • For a Fast Ethernet interface, enter the keyword FastEthernet then the slot/ port information.
PAGE 960
clear lldp neighbors Clear LLDP neighbor information for all interfaces or a specific interface. Z9000 Syntax Parameters clear lldp neighbors {interface} interface Defaults none Command Modes EXEC Privilege Command History Enter the following keywords and slot/port or number information: • For a Fast Ethernet interface, enter the keyword FastEthernet then the slot/ port information. • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet followed by the slot/ port information.
PAGE 961
To disable debugging, use the no debug lldp interface {interface | all}{events} {packet {brief | detail} {tx | rx | both}} command. Parameters interface Enter the following keywords and slot/port or number information: • For a Fast Ethernet interface, enter the keyword FastEthernet then the slot/ port information. • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet followed by the slot/ port information.
PAGE 962
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Introduced on the S-Series. Version 7.6.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced on the E-Series. disable Enable or disable LLDP. Z9000 Syntax disable To enable LLDP, use the no disable command.
PAGE 963
show lldp neighbors — displays the LLDP neighbors. hello Configure the rate at which the LLDP control packets are sent to its peer. Z9000 Syntax hello seconds To revert to the default, use the no hello seconds command. Parameters seconds Enter the rate, in seconds, at which the control packets are sent to its peer. The rate is from 5 to 180 seconds. The default is 30 seconds.
PAGE 964
Command Modes LLDP (conf-lldp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.2) Usage Information Introduced on the Z9000 and S4810. To enable LLDP on the management interface, use the no disable command in LLDP-MANAGEMENT-INTERFACE mode (conf-lldp-mgmtIf).
PAGE 965
Related Commands protocol lldp (Configuration) — enables LLDP globally. show lldp neighbors — displays the LLDP neighbors. multiplier Set the number of consecutive misses before LLDP declares the interface dead. Z9000 Syntax multiplier integer To return to the default, use the no multiplier integer command. Parameters integer Enter the number of consecutive misses before the LLDP declares the interface dead. The range is from 2 to 10.
PAGE 966
Command Modes CONFIGURATION (conf-lldp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.
PAGE 967
Version 7.4.1.0 Usage Information Introduced on the E-Series. Before LLDP can be configured on an interface, it must be enabled globally from CONFIGURATION mode. This command places you in LLDP mode on the interface; it does not enable the protocol. When you enter the LLDP protocol in the Interface context, it overrides global configurations. When you execute the no protocol lldp from INTERFACE mode, interfaces begin to inherit the configuration from global LLDP CONFIGURATION mode.
PAGE 968
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Introduced on the S-Series. Version 7.6.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced on the E-Series. Usage Information Omitting the keyword detail displays only the remote chassis ID, Port ID, and Dead Interval.
PAGE 969
Number of Table Drops : Number of Table Age Outs : Dell# 0 400 show management-interface Display LLDP management interface configuration information. Z9000 Syntax show management-interface Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2. (0.
PAGE 970
Example Dell#show running-config lldp ! protocol lldp advertise dot1-tlv port-protocol-vlan-id port-vlan-id advertise dot3-tlv max-frame-size advertise management-tlv system-capabilities systemdescription hello 15 multiplier 3 no disable Dell# LLDP-MED Commands The following are the LLDP-MED (Media Endpoint Discovery) commands. Dell Networking OS LLDP-MED commands are an extension of the set of LLDP TLV advertisement commands. The C-Series and S-Series support all commands.
PAGE 971
To return to the default, use the no advertise med guest-voice {vlan-id layer2_priority DSCP_value} | {priority-tagged number} command. Parameters vlan-id Enter the VLAN ID. The range is from 1 to 4094. layer2_priority Enter the Layer 2 priority. The range is from 0 to 7. DSCP_value Enter the DSCP value. The range is from 0 to 63. priority-tagged number Enter the keywords priority-tagged followed the Layer 2 priority. The range is from 0 to 7. Defaults Unconfigured.
PAGE 972
Parameters vlan-id Enter the VLAN ID. The range is from 1 to 4094. layer2_priority Enter the Layer 2 priority. The range is from 0 to 7. DSCP_value Enter the DSCP value. The range is from 0 to 63. priority-tagged number Enter the keywords priority-tagged then the Layer 2 priority. The range is from 0 to 7. Defaults unconfigured. Command Modes CONFIGURATION (conf-lldp) Command History This guide is platform-specific.
PAGE 973
civic-based value Enter the keywords civic-based then the civic based location in hexadecimal format. The range is from 6 to 255 bytes. ecs-elin value Enter the keywords ecs-elin then the Emergency Call Service (ecs) Emergency Location Identification Number (elin) numeric location string. The range is from 10 to 25 characters. Defaults unconfigured. Command Modes CONFIGURATION (conf-lldp) Command History This guide is platform-specific.
PAGE 974
Command Modes CONFIGURATION (conf-lldp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.
PAGE 975
Defaults unconfigured. Command Modes CONFIGURATION (conf-lldp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810.
PAGE 976
Defaults unconfigured. Command Modes CONFIGURATION (conf-lldp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810.
PAGE 977
Command Modes CONFIGURATION (conf-lldp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.
PAGE 978
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Introduced on the S-Series. Version 7.6.1.
PAGE 979
The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Introduced on the S-Series. Version 7.6.1.0 Introduced on the C-Series and E-Series. debug lldp interface — debugs LLDP. show lldp neighbors — displays the LLDP neighbors.
PAGE 980
Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Introduced on the S-Series. Version 7.6.1.0 Introduced on the C-Series and E-Series. debug lldp interface — debugs LLDP. show lldp neighbors — displays the LLDP neighbors.
PAGE 981
Microsoft Network Load Balancing 30 This functionality is supported on the Z9000 platform. Network Load Balancing (NLB) is a clustering functionality that is implemented by Microsoft on Windows 2000 Server and Windows Server 2003 operating systems. NLB uses a distributed methodology or pattern to equally split and balance the network traffic load across a set of servers that are part of the cluster or group.
PAGE 982
response with MAC-s4 is received as the last one). The interface associated with server, S4, is added to the ARP table. • With NLB feature enabled, after learning the NLB ARP entry, all the subsequent traffic is flooded on all ports in VLAN1. With NLB, the data frame is forwarded to all the servers for them to perform load-balancing. NLB Multicast Mode Scenario Consider a sample topology in which four servers, namely S1 through S4, are configured as a cluster or a farm.
PAGE 983
learned, traffic is forwarded to only one server rather than the entire cluster, and failover and balancing are not preserved. To preserve failover and balancing, the switch forwards the traffic destined for the server cluster to all member ports in the VLAN connected to the cluster. To ensure that this happens, you must configure the ip vlan-flooding command on the Dell switch at the time that the Microsoft cluster is configured.
PAGE 984
Defaults Not configured. Command Modes CONFIGURATION Command History Version 9.3(0.0) • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • The interface specified here must be one of the interfaces configured using the {output-range | output} interface option with the mac-addresstable static command.
PAGE 985
NOTE: Use this option if you want multicast functionality in an L2 VLAN without IGMP protocols. output interface output-range interface vlan vlan-id For a multicast MAC address, enter the keyword output then one of the following interfaces for which traffic is forwarded: • For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 986
ip vlan-flooding Enable unicast data traffic flooding on VLAN member ports. Syntax ip vlan-flooding To disable, use the no ip vlan-flooding command. Command Modes Command History CONFIGURATION Version 9.3(0.0) Introduced on the S4810, S4820T, S6000, Z9000, and MXL platforms Default Disabled Usage Information By default this command is disabled. There might be some ARP table entries which are resolved through ARP packets which had Ethernet MAC SA different from MAC information inside the ARP packet.
PAGE 987
Multicast Source Discovery Protocol (MSDP) 31 Multicast source discovery protocol (MSDP) connects multiple PIM Sparse-Mode (PIM-SM) domains together. MSDP peers connect using TCP port 639. Peers send keepalives every 60 seconds. A peer connection is reset after 75 seconds if no MSDP packets are received. MSDP connections are parallel with MBGP connections. The Dell Networking operating system supports MSDP commands on the Z9000 platform.
PAGE 988
clear ip msdp sa-cache Clears the entire source-active cache, the source-active entries of a particular multicast group, rejected, or local source-active entries. Z9000 Syntax Parameters clear ip msdp sa-cache [group-address | rejected-sa | local] group-address Enter the group IP address in dotted decimal format (A.B.C.D.).
PAGE 989
clear ip msdp statistic Clears the entire source-active cache, the source-active entries of a particular multicast group, rejected, or local source-active entries. Z9000 Syntax Parameters clear ip msdp sa-cache [group-address | rejected-sa | local] group-address Enter the group IP address in dotted decimal format (A.B.C.D.).
PAGE 990
debug ip msdp Turn on MSDP debugging. Z9000 Syntax debug ip msdp {event peer address | packet peer address | pim} To turn debugging off, use the no debug ip msdp {event peer address | packet peer address | pim} command. Parameters event peer address Enter the keyword event then the peer address in a dotted decimal format (A.B.C.D.). packet peer address Enter the keyword packet then the peer address in a dotted decimal format (A.B.C.D.). pim Enter the keyword pim to debug advertisement from PIM.
PAGE 991
Parameters number Enter the number of rejected SA entries to cache. The range is from 0 to 32766. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T.
PAGE 992
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.
PAGE 993
ip msdp mesh-group To be a member of a mesh group, configure a peer. Z9000 Syntax ip msdp mesh-group {name} {peer address} To remove the peer from a mesh group, use the no ip msdp mesh-group {name} {peer address} command. Parameters name Enter a string of up to 16 characters long for as the mesh group name. peer address Enter the peer address in a dotted decimal format (A.B.C.D.). Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 994
ip msdp originator-id Configure the MSDP Originator ID. Z9000 Syntax ip msdp originator-id {interface} To remove the originator-id, use the no ip msdp originator-id {interface} command. Parameters interface Enter the following keywords and slot/port or number information: • For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. • For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128.
PAGE 995
ip msdp peer Configure an MSDP peer. Z9000 Syntax ip msdp peer peer address [connect-source] [description] [salimit number] To remove the MSDP peer, use the no ip msdp peer peer address [connect-source interface] [description name] [sa-limit number] command. Parameters peer address Enter the peer address in a dotted decimal format (A.B.C.D.).
PAGE 996
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 7.5.1.0 Added option for SA upper limit and the description option. Version 6.2.1.1 Introduced The connect-source option is used to supply a source IP address for the TCP connection.
PAGE 997
The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced Modifications to the ACL do not have an immediate effect on the sa-cache. To apply the redistribute filter to entries already present in the SA cache, use the clear ip msdp sa-cache local command.
PAGE 998
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Introduced on the E-Series. ip msdp sa-limit Configure the upper limit of source-active (SA) entries in SA-cache. Z9000 Syntax ip msdp sa-limit number To return to the default, use the no ip msdp sa-limit number command. Parameters number Enter the maximum number of SA entries in SA-cache.
PAGE 999
continue to be accepted. To enforce the limit in such situation, use the clear ip msdp sa-cache command. Related Commands ip msdp peer — configures the MSDP peer. clear ip msdp peer — clears the MSDP peer. show ip msdp — displays the MSDP information ip msdp shutdown Administratively shut down a configured MSDP peer. Z9000 Syntax Parameters ip msdp shutdown {peer address} peer address Enter the peer address in a dotted decimal format (A.B.C.D.). Defaults Not configured.
PAGE 1000
ip multicast-msdp Enable MSDP. Z9000 Syntax ip multicast-msdp To exit MSDP, use the no ip multicast-msdp command. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T.
PAGE 1001
Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 6.2.1.
PAGE 1002
show ip msdp sa-cache rejected-sa Display the rejected SAs in the SA cache. Z9000 Syntax show ip msdp sa-cache rejected-sa Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example 1002 Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 1003
32 Multiple Spanning Tree Protocol (MSTP) Multiple spanning tree protocol (MSTP), as implemented by the Dell Networking operating system, conforms to IEEE 802.1s. This command supports the Dell Networking Z9000 platform. debug spanning-tree mstp Enable debugging of the multiple spanning tree protocol and view information on the protocol.
PAGE 1004
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.3.7.
PAGE 1005
Related Commands Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.5.1.0 Introduced. protocol spanning-tree mstp — enters MULTIPLE SPANNING TREE mode. forward-delay The amount of time the interface waits in the Blocking State and the Learning State before transitioning to the Forwarding State.
PAGE 1006
Related Commands Version 7.5.1.0 Introduced on the C-Series. Version 6.5.1.0 Introduced. max-age — changes the wait time before MSTP refreshes protocol configuration information. hello-time — changes the time interval between bridge protocol data units (BPDUs). hello-time Set the time interval between generation of MSTB bridge protocol data units (BPDUs). Z9000 Syntax hello-time seconds To return to the default value, use the no hello-time command.
PAGE 1007
max-age — changes the wait time before MSTP refreshes protocol configuration information. max-age To maintain configuration information before refreshing that information, set the time interval for the MSTB. Z9000 Syntax max-age seconds To return to the default values, use the no max-age command. Parameters max-age Enter a number of seconds the Dell Networking OS waits before refreshing configuration information. The range is from 6 to 40. The default is 20 seconds.
PAGE 1008
max-hops Configure the maximum hop count. Z9000 Syntax max-hops number To return to the default values, use the no max-hops command. Parameters range Enter a number for the maximum hop count. The range is from 1 to 40. The default is 20. Defaults 20 hops Command Modes MULTIPLE SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1009
msti Configure multiple spanning tree instance, bridge priority, and one or multiple VLANs mapped to the MST instance. Z9000 Syntax msti instance {vlan range | bridge-priority priority} To disable mapping or bridge priority, use the no msti instance {vlan range | bridge-priority priority} command. Parameters msti instance Enter the MSTP instance. The range is from zero (0) to 63. vlan range Enter the keyword vlan then the identifier range value. The range is from 1 to 4094.
PAGE 1010
name The name you assign to the multiple spanning tree region. Z9000 Syntax name region-name To remove the region name, use the no name command. Parameters region-name Enter the MST region name. The range is 32 character limit. Defaults no default name. Command Modes MULTIPLE SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1011
protocol spanning-tree mstp To enable and configure the multiple spanning tree group, enter MULTIPLE SPANNING TREE mode. Z9000 Syntax protocol spanning-tree mstp To disable the multiple spanning tree group, use the no protocol spanningtree mstp command. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1012
revision The revision number for the multiple spanning tree configuration. Z9000 Syntax revision range To return to the default values, use the no revision command. Parameters range Enter the revision number for the MST configuration. The range is from 0 to 65535. The default is 0. Defaults 0 Command Modes MULTIPLE SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1013
show config View the current configuration for the mode. Only non-default values are shown. Z9000 Syntax show config Command Modes MULTIPLE SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T.
PAGE 1014
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.
PAGE 1015
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.4.2.1 Support for the optional keyword guard was added on the C-Series, S-Series, and E-Series TeraScale. Version 8.
PAGE 1016
BPDU (Mrecords): sent 7, received 1103 The port is not in the portfast mode Example (EDS and LBK) The bold line shows the loopback BPDU inconsistency (LBK_INC). Dell#show spanning-tree msti 0 brief MSTI 0 VLANs mapped 1-4094 Executing IEEE compatible Spanning Tree Protocol Root ID Priority 32768, Address 0001.e801.6aa8 Root Bridge hello time 2, max age 20, forward delay 15, max hops 20 Bridge ID Priority 32768, Address 0001.e801.
PAGE 1017
Example (Guard) Field Description Instance MSTP instance. Sts Port state: root-inconsistent (INCON Root), forwarding (FWD), listening (LIS), blocking (BLK), or shut down (EDS Shut). Guard Type Type of STP guard configured (Root, Loop, or BPDU guard).
PAGE 1018
Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series. spanning-tree msti Configure multiple spanning tree instance cost and priority for an interface. Z9000 Syntax Parameters spanning-tree msti instance {cost cost | priority priority} msti instance Enter the keyword msti and the MST instance number. The range is from zero (0) to 63. cost cost (OPTIONAL) Enter the keyword cost then the port cost value.
PAGE 1019
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.5.1.0 Introduced on the E-Series. spanning-tree mstp edge-port Configures the interface as an MST edge port and optionally a Bridge Protocol Data Unit (BPDU) guard.
PAGE 1020
Usage Information Version 8.3.7.1 Introduced on the S4810. Version 8.2.1.0 Introduced the hardware shutdown-on-violation option. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.5.1.0 Introduced on the E-Series. On an MSTP switch, a port configured as an edge port immediately transitions to the Forwarding state. Only configure ports connected to end-hosts as edge ports. Consider an edge port similar to a port with spanning-tree portfast enabled.
PAGE 1021
Usage Information By default, Dell Networking OS implements an optimized flush mechanism for MSTP. This mechanism helps in flushing the MAC addresses only when necessary (and less often) allowing for faster convergence during topology changes. However, if a standards-based flush mechanism is needed, this knob command can be turned on to enable flushing MAC addresses after receiving every topology change notification.
PAGE 1022
PAGE 1023
33 Multicast The multicast commands are supported by Dell Networking operating system (OS) on all Z9000 platform. This chapter contains the following sections: • IPv4 Multicast Commands IPv4 Multicast Commands The following section contains the IPv4 multicast commands. clear ip mroute Clear learned multicast routes on the multicast forwarding table. To clear the protocol-independent multicast (PIM) tree information base, use the clear ip pim tib command.
PAGE 1024
Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the C-Series. E-Series legacy command Related Commands show ip pim tib — shows the PIM tree information base. ip mroute Assign a static mroute.
PAGE 1025
distance (OPTIONAL) Enter a number as the distance metric assigned to the mroute. The range is from 0 to 255. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T.
PAGE 1026
Usage Information Version 7.8.1.0 Introduced on the C-Series. Version 7.6.1.0 Introduced on the E-Series. This feature allows you to limit the number of multicast entries on the system. This number is the total of all the multicast entries on all line cards in the system. On each line card, the multicast module only installs the maximum number of entries, depending on the configured CAM profile. To store multicast routes, use the IN-L3-McastFib CAM partition.
PAGE 1027
Related Commands ip pim sparse-mode — enables IGMP and PIM on an interface. show ip mroute View the multicast routing table. Z9000 Syntax Parameters show ip mroute [static | group-address [source-address] | count | snooping [vlan vlan-id] [group-address [source-address]] | summary | vlt [group-address [source-address] | count] static (OPTIONAL) Enter the keyword static to view static multicast routes.
PAGE 1028
Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 9.2. (0.0) Added support for keyword vlt to the Z9000, S4810, and S4820T. Version 8.4.1.
PAGE 1029
Example (VLT) Dell#show ip mroute vlt IP Multicast Routing Table Flags: S – Synced (*, 225.1.1.1), uptime 00:39:33 flags: S Incoming interface: Vlan 10 Spanned outgoing interface list: Vlan 20 (S) Vlan 30 (50.1.1.2, 225.1.1.1), uptime 00:39:33 flags: S Incoming interface: Vlan 10 Spanned outgoing interface list: Vlan 20 (S) Usage Information Example The following describes the show ip mroute command shown in the following example.
PAGE 1030
show ip rpf View reverse path forwarding. Z9000 Syntax show ip rpf Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.
PAGE 1031
debug ipv6 mld_host Enable the collection of debug information for MLD host transactions. Z9000 Syntax [no] debug ipv6 mld_host [int-count | interface type] [slot/ port-range] To discontinue collection of debug information for the MLD host transactions, use the no debug ipv6 mld_host command. Parameters int-count Enter the keyword count to indicate the number of required debug messages.
PAGE 1032
ip multicast-limit To limit the number of multicast entries on the system, use this feature. Z9000 Syntax Parameters ip multicast-limit limit limit Enter the desired maximum number of multicast entries on the system. The S-Series range is from 1 to 2000. Defaults The S-Series default is 400. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1033
Open Shortest Path First (OSPFv2 and OSPFv3) 34 Open Shortest Path First version 2 for IPv4 is supported on Z9000 Dell Networking Operating System (OS) platform. Open Shortest Path First version 3 (OSPFv3) for IPv6 is supported on the Z9000 platform. OSPF is an Interior Gateway Protocol (IGP), which means that it distributes routing information between routers in a single Autonomous System (AS).
PAGE 1034
Defaults cost = 1; no areas are configured. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.
PAGE 1035
no-summary (OPTIONAL) Specify that no summary LSAs should be sent into the NSSA. Defaults Not configured. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.
PAGE 1036
Defaults Not configured. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.
PAGE 1037
Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.
PAGE 1038
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Added support for the Multi-Process OSPF. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series. clear ip ospf Clear all OSPF routing tables.
PAGE 1039
pre-Version 6.1.1.1 Introduced on the E-Series. clear ip ospf statistics Clear the packet statistics in interfaces and neighbors. Z9000 Syntax Parameters clear ip ospf [process-id] [vrf vrf-name] statistics [interface name {neighbor router-id}] process-id Enter the OSPF Process ID to clear a specific process. If no Process ID is entered, all OSPF processes are cleared. vrf vrf-name Enter the keyword vrf followed by the name of the VRF to clear all OSPF routing tables corresponding to that VRF.
PAGE 1040
Related Commands Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Added support for the Multi-Process OSPF. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series. show ip ospf statistics — displays the OSPF statistics. debug ip ospf Display debug information on OSPF.
PAGE 1041
The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.8.0 Added the database-timer rate-limit option for the S4810. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Added support for the Multi-Process OSPF. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series.
PAGE 1042
Field Description • Example 2 - MD5 authentication configured using the ip ospf message-digest-key command auk: If the ip ospf authentication-key command is configured, this field displays the key used. keyid: If the ip ospf message-digest-key command is configured, this field displays the MD5 key to: Displays the interface to which the packet is intended. dst: Displays the destination IP address. netmask: Displays the destination IP address mask.
PAGE 1043
default-information originate To generate a default external route into an OSPF routing domain, configure Dell Networking Operating System (OS). Z9000 Syntax default-information originate [always] [metric metric-value] [metric-type type-value] [route-map map-name] To return to the default values, use the no default-information originate command. Parameters always (OPTIONAL) Enter the keyword always to specify that default route information must always be advertised.
PAGE 1044
pre-Version 6.1.1.1 Related Commands Introduced on the E-Series. redistribute — redistributes routes from other routing protocols into OSPF. default-metric Change the metrics of redistributed routes to a value useful to OSPF. Use this command with the redistribute command. Z9000 Syntax default-metric number To return to the default values, use the no default-metric [number] command. Parameters number Enter a number as the metric. The range is from 1 to 16777214. Defaults Disabled.
PAGE 1045
description Add a description about the selected OSPF configuration. Z9000 Syntax description description To remove the OSPF description, use the no description command. Parameters description Enter a text string description to identify the OSPF configuration (80 characters maximum). Defaults none Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1046
Parameters weight Specify an administrative distance. The range is from 1 to 255. The default is 110. ip-address (OPTIONAL) Enter a router ID in the dotted decimal format. If you enter a router ID, include the mask for that router address. mask (OPTIONAL) Enter a mask in dotted decimal format or /n format. access-listname (OPTIONAL) Enter the name of an IP standard access list, up to 140 characters. Defaults 110 Command Modes ROUTER OSPF Command History This guide is platform-specific.
PAGE 1047
Defaults inter-area dist2 (OPTIONAL) Enter the keywords inter-area then a number to specify a distance metric for routes between areas. The range is from 1 to 255. The default is 110. intra-area dist1 (OPTIONAL) Enter the keywords intra-area then a number to specify a distance metric for all routes within an area. The range is from 1 to 255. The default is 110.
PAGE 1048
Parameters prefix-listname Enter the name of a configured prefix list. interface (OPTIONAL) Enter one of the following keywords and slot/ port or number information: • For Port Channel groups, enter the keywords portchannel then a number. For the C-Series and S-Series, the range is from 1 to 128. • For a SONET interface, enter the keyword sonet then the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 1049
To remove a filter, use the no distribute-list prefix-list-name out [bgp | connected | isis | rip | static] command. Parameters prefix-listname Enter the name of a configured prefix list. bgp (OPTIONAL) Enter the keyword bgp to specify that BGP routes are distributed. NOTE: BGP and ISIS routes are not available on the CSeries. BGP, ISIS, and RIP routes are not available on the S-Series. connected (OPTIONAL) Enter the keyword connected to specify that connected routes are distributed.
PAGE 1050
Usage Information Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series. The distribute-list out command applies to routes autonomous system boundary routers (ASBRs) redistributes into OSPF. It can be applied to external type 2 and external type 1 routes, but not to intra-area and inter-area routes. enable inverse-mask By default, Dell Networking Operating System (OS) allows you to input the OSPF network command with a net-mask.
PAGE 1051
Parameters number Enter the convergence level desired. The higher this parameter is set, the faster OSPF converge takes place. The range is from 1 to 4. Defaults none. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.
PAGE 1052
Defaults Not Configured Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.
PAGE 1053
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.12.0 Introduced on the S4810. Version 7.8.1.0 Restart role enabled on the S-Series (Both Helper and Restart roles now supported on S-Series). Added support for Multi-Process OSPF. Version 7.7.1.0 Added Helper-Role support on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series.
PAGE 1054
Version 8.3.11.1 Introduced on the Z9000. Version 8.3.12.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series. graceful-restart role Specify the role for your OSPF router during graceful restart. Z9000 Syntax graceful-restart role [helper-only | restart-only] To disable graceful restart role, use the no graceful-restart role command.
PAGE 1055
pre-Version 6.1.1.1 Introduced on the E-Series. ip ospf auth-change-wait-time OSPF provides a grace period while OSPF changes its interface authentication type. During the grace period, OSPF sends out packets with new and old authentication scheme until the grace period expires. Z9000 Syntax ip ospf auth-change-wait-time seconds To return to the default, use the no ip ospf auth-change-wait-time command. Parameters seconds Enter the seconds. The range is from 0 to 300. Defaults zero (0) seconds.
PAGE 1056
Parameters encryptiontype (OPTIONAL) Enter 7 to encrypt the key. key Enter an eight-character string. Strings longer than eight characters are truncated. Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.
PAGE 1057
The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series. If this command is not configured, cost is based on the auto-cost command.
PAGE 1058
Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series. Usage Information By default, the dead interval is four times the default hello-interval. Related Commands ip ospf hello-interval — sets the time interval between the hello packets. ip ospf hello-interval Specify the time interval between the hello packets sent on the interface.
PAGE 1059
Usage Information The time interval between the hello packets must be the same for routers in a network. Related Commands ip ospf dead-interval — sets the time interval before a router is declared dead. ip ospf message-digest-key Enable OSPF MD5 authentication and send an OSPF message digest key on the interface. Z9000 Syntax ip ospf message-digest-key keyid md5 key To delete a key, use the no ip ospf message-digest-key keyid command. Parameters keyid Enter a number as the key ID.
PAGE 1060
authenticated with the old key and the second packet authenticated with the new key. This process ensures that the neighbors learn the new key and communication is not disrupted by keeping the old key enabled. After the reply is received and the new key is authenticated, delete the old key. Dell recommends keeping only one key per interface. NOTE: The MD5 secret is stored as plain text in the configuration file with service password encryption. Write down or otherwise record the key.
PAGE 1061
ip ospf network Set the network type for the interface. Z9000 Syntax ip ospf network {broadcast | point-to-point} To return to the default, use the no ip ospf network command. Parameters broadcast Enter the keyword broadcast to designate the interface as part of a broadcast network. point-to-point Enter the keywords point-to-point to designate the interface as part of a point-to-point network. Defaults Broadcast. Command Modes ROUTER OSPF Command History This guide is platform-specific.
PAGE 1062
Parameters number Enter a number as the priority. The range is from 0 to 255. The default is 1. Defaults 1 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.
PAGE 1063
Defaults 5 seconds Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.
PAGE 1064
The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series.
PAGE 1065
maximum-paths Enable the software to forward packets over multiple paths. Z9000 Syntax maximum-paths number To disable packet forwarding over multiple paths, use the no maximum-paths command. Parameters number Specify the number of paths. The range for OSPFv2 is from 1 to 64. The default for OSPFv2 is 4 paths. The range for OSPFv3 is from 1 to 64. The default for OSPFv3 is 8 paths. Defaults 4 Command Modes ROUTER OSPF for OSPFv2 Command History This guide is platform-specific.
PAGE 1066
To disable an OSPF area, use the no network ip-address mask area areaid command. Parameters ip-address Specify a primary or secondary address in dotted decimal format. The primary address is required before adding the secondary address. mask Enter a network mask in /prefix format. (/x) area-id Enter the OSPF area ID as either a decimal value or in a valid IP address. Decimal value range is from 0 to 65535. IP address format is dotted decimal format A.B.C.D.
PAGE 1067
passive-interface Suppress both receiving and sending routing updates on an interface. Z9000 Syntax passive-interface {default | interface} To enable both the receiving and sending routing, use the no passiveinterface interface command. To return all OSPF interfaces (current and future) to active, use the no passiveinterface default command. Parameters default Enter the keyword default to make all OSPF interfaces (current and future) passive.
PAGE 1068
Usage Information Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Modified to include the keyword default. pre-Version 6.1.1.1 Introduced on the E-Series. Although the passive interface does not send or receive routing updates, the network on that interface is still included in OSPF updates sent using other interfaces. The default keyword sets all interfaces as passive.
PAGE 1069
On configuring suppression using the passive-interface command, the state of the OSPF neighbor does not change to INIT; instead, the state of the OSPF neighbor changes to DOWN after the dead-timer expires. redistribute Redistribute information from another routing protocol throughout the OSPF process.
PAGE 1070
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Added support for Multi-Process OSPF.
PAGE 1071
• 2 = for OSPF External type 2 route-map map-name (OPTIONAL) Enter the keywords route-map then the name of the route map. tag tag-value (OPTIONAL) Enter the keyword tag to set the tag for routes redistributed into OSPF. The range is from 0 to 4294967295. Defaults none Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1072
level-1 (OPTIONAL) Enter the keywords level-1 to redistribute only IS-IS Level-1 routes. level-1-2 (OPTIONAL) Enter the keywords level-1-2 to redistribute both IS-IS Level-1 and Level-2 routes. level-2 (OPTIONAL) Enter the keywords level-2 to redistribute only IS-IS Level-2 routes. metric metricvalue (OPTIONAL) Enter the keyword metric then a number. The range is from 0 (zero) to 4294967295.
PAGE 1073
router-id To configure a fixed router ID, use this command. Z9000 Syntax router-id ip-address To remove the fixed router ID, use the no router-id ip-address command. Parameters ip-address Enter the router ID in the IP address format. Defaults none. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1074
n]: Dell# router ospf To configure an OSPF instance, enter ROUTER OSPF mode. Z9000 Syntax router ospf process-id To clear an OSPF instance, use the no router ospf process-id command. Parameters process-id Enter a number for the OSPF instance. The range is from 1 to 65535. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1075
show config Display the non-default values in the current OSPF configuration. Z9000 Syntax show config Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.
PAGE 1076
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.8.0 Added output for LSA throttling timers. Version 8.3.7.0 Introduced on the S4810.
PAGE 1077
vrf Supports only single TOS (TOS0) routes SPF schedule delay 5 secs, Hold time between two SPFs 10 secs Convergence Level 0 Min LSA origination 0 msec, Min LSA arrival 1000 msec Min LSA hold time 5000 msec, Max LSA wait time 5000 msec Number of area in this router is 1, normal 1 stub 0 nssa 0 Area BACKBONE (0) Number of interface in this area is 1 SPF algorithm executed 205 times Area ranges are Dell# Related Commands show ip ospf database — displays information about the OSPF routes configured.
PAGE 1078
Usage Information Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series and E-Series. To isolate problems with external routes, use this command. In OSPF, external routes are calculated by adding the LSA cost to the cost of reaching the ASBR router. If an external route does not have the correct cost, use this command to determine if the path to the originating router is correct. The display output is not sorted in any order.
PAGE 1079
Usage Information Example Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Added support of Multi-Process OSPF. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series. The following describes the show ip ospf process-id database command shown in the following example. Field Description Link ID Identifies the router ID.
PAGE 1080
13.1.1.0 13.1.2.0 172.16.1.0 Dell> Related Commands 13.1.1.1 13.1.1.1 13.1.1.1 1192 0x8000006b 0x2718 1184 0x8000006b 0x1c22 148 0x8000006d 0x533b 0 0 0 show ip ospf database asbr-summary — displays only ASBR summary LSA information. show ip ospf database asbr-summary Display information about autonomous system (AS) boundary LSAs.
PAGE 1081
Usage Information Example Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series. The following describes the show ip ospf database asbr-summary command shown in the following example. Field Description LS Age Displays the LSA’s age. Options Displays the optional capabilities available on router.
PAGE 1082
LS age: 473 Options: (No TOS-capability, No DC, E) LS type: Summary Asbr Link State ID: 104.1.50.1 Advertising Router: 1.1.1.10 LS Seq Number: 0x80000010 Checksum: 0x4198 Length: 28 --More-Related Commands show ip ospf database — displays OSPF database information. show ip ospf database external Display information on the AS external (type 5) LSAs.
PAGE 1083
Usage Information Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Added support for Multi-Process OSPF. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series. The following describes the show ip ospf process-id database external command shown in the following example. Field Description LS Age Displays the LSA’s age.
PAGE 1084
Example Field Description External Route Tag Displays the 32-bit field attached to each external route. The OSPF protocol does not use this field, but you can use the field for external route management. Dell#show ip ospf 1 database external OSPF Router with ID (20.20.20.5) (Process ID 1) Type-5 AS External LS age: 612 Options: (No TOS-capability, No DC, E) LS type: Type-5 AS External Link State ID: 12.12.12.2 Advertising Router: 20.31.3.
PAGE 1085
link-state-id adv-router ipaddress (OPTIONAL) Specify LSA ID in dotted decimal format. The LSA ID value depends on the LSA type, and it can be one of the following: • the network’s IP address for Type 3 LSAs or Type 5 LSAs • the router’s OSPF router ID for Type 1 LSAs or Type 4 LSAs • the default destination (0.0.0.0) for Type 5 LSAs (OPTIONAL) Enter the keywords adv-router and the ipaddress to display only the LSA information about that router.
PAGE 1086
Field Example Description • DC or No DC is displayed depending on whether the originating router can support OSPF over demand circuits. • E or No E is displayed on whether the originating router can accept AS External LSAs. LS Type Displays the LSA’s type. Link State ID Displays the Link State ID. Advertising Router Identifies the router ID of the LSA’s originating router. Checksum Identifies the link state sequence number. This number enables you to identify old or duplicate LSAs.
PAGE 1087
show ip ospf database nssa-external Display NSSA-External (type 7) LSA information. Z9000 Syntax Parameters show ip ospf [process-id] database nssa-external [link-stateid] [adv-router ip-address] process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. link-state-id (OPTIONAL) Specify LSA ID in dotted decimal format.
PAGE 1088
Related Commands show ip ospf database — displays OSPF database information. show ip ospf database opaque-area Display the opaque-area (type 10) LSA information. Z9000 Syntax Parameters show ip ospf [process-id] database opaque-area [link-state-id] [adv-router ip-address] process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. link-state-id (OPTIONAL) Specify LSA ID in dotted decimal format.
PAGE 1089
pre-Version 6.1.1.1 Usage Information Example Introduced on the E-Series. The following describes the show ip ospf process-id database opaquearea command shown in the following example. Item Description LS Age Displays the LSA’s age. Options Displays the optional capabilities available on router. The following options can be found in this item: • TOS-capability or No TOS-capability is displayed depending on whether the router can support Type of Service.
PAGE 1090
Advertising Router: 10.16.1.160 LS Seq Number: 0x80000002 Checksum: 0x19c2 --More-Related Commands show ip ospf database — displays OSPF database information. show ip ospf database opaque-as Display the opaque-as (type 11) LSA information. Syntax Parameters show ip ospf process-id database opaque-as [link-state-id] [adv-router ip-address] process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process.
PAGE 1091
Related Commands Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series. show ip ospf database — displays OSPF database information. show ip ospf database opaque-link Display the opaque-link (type 9) LSA information. Z9000 Syntax Parameters show ip ospf [process-id] database opaque-link [link-state-id] [adv-router ip-address] process-id Enter the OSPF Process ID to show a specific process.
PAGE 1092
Related Commands Version 7.8.1.0 Added support for Multi-Process OSPF. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series. show ip ospf database — displays OSPF database information. show ip ospf database router Display the router (type 1) LSA information.
PAGE 1093
Usage Information Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Added support for Multi-Process OSPF. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series. The following describes the show ip ospf process-id database router command shown in the following example. Item Description LS Age Displays the LSA age. Options Displays the optional capabilities available on router.
PAGE 1094
Example Dell#show ip ospf 100 database router OSPF Router with ID (1.1.1.10) (Process ID 100) Router (Area 0) LS age: 967 Options: (No TOS-capability, No DC, E) LS type: Router Link State ID: 1.1.1.10 Advertising Router: 1.1.1.10 LS Seq Number: 0x8000012f Checksum: 0x3357 Length: 144 AS Boundary Router Area Border Router Number of Links: 10 Link connected to: a Transit Network (Link ID) Designated Router address: 192.68.129.1 (Link Data) Router Interface address: 192.68.129.
PAGE 1095
show ip ospf database summary Display the network summary (type 3) LSA routing information. Z9000 Syntax Parameters show ip ospf [process-id] database summary [link-state-id] [adv-router ip-address] process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. link-state-id (OPTIONAL) Specify LSA ID in dotted decimal format.
PAGE 1096
Usage Information Example The following describes the show ip ospf process-id database summary command shown in the following example. Item Description LS Age Displays the LSA age. Options Displays the optional capabilities available on router. The following options can be found in this item: • TOS-capability or No TOS-capability is displayed depending on whether the router can support Type of Service.
PAGE 1097
LS Seq Number: 0x80000016 Checksum: 0x987c Length: 28 Network Mask: /24 TOS: 0 Metric: 1 LS age: 7 Options: (No TOS-capability, No DC, E) LS type: Summary Network Link State ID: 192.68.33.0 Advertising Router: 1.1.1.10 LS Seq Number: 0x80000016 Checksum: 0x1241 Length: 28 Network Mask: /26 TOS: 0 Metric: 1 Dell# Related Commands show ip ospf database — displays OSPF database information. show ip ospf interface Display the OSPF interfaces configured.
PAGE 1098
• Command History EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information 1098 Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.
PAGE 1099
Example Item Description Neighbor Count... This line displays the number of neighbors and adjacent neighbors. Listed below this line are the details about each adjacent neighbor. Dell>show ip ospf int GigabitEthernet 13/17 is up, line protocol is up Internet Address 192.168.1.2/30, Area 0.0.0.1 Process ID 1, Router ID 192.168.253.2, Network Type BROADCAST, Cost: 1 Transmit Delay is 1 sec, State DR, Priority 1 Designated Router (ID) 192.168.253.2, Interface address 192.168.1.
PAGE 1100
Parameters process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Example Version 9.0.2.0 Introduced on the S6000..
PAGE 1101
show ip ospf routes Display routes OSPF calculates and stores in OSPF RIB. Z9000 Syntax Parameters show ip ospf [process-id] routes process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1102
NOTE: Starting with Version 9.4(0.0), the loopback IP address advertised to the neighbor is not displayed in the output because they are not accounted as inactive OSPF routes, whereas the loopback IP address is displayed until Dell Networking OS Version 9.3(0.0). Starting with Version 9.4(0.0), the show ip ospf routes command displays the interface and area ID information of connected networks in addition to the other settings, whereas these details are not displayed until Dell Networking OS Version 9.3(0.
PAGE 1103
• neighbor router-id For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. (OPTIONAL) Enter the keyword neighbor then the neighbor’s router-id in dotted decimal format (A.B.C.D.). Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1104
Row Heading Description Tx-Mark The highest number mark in the transmission queue. Rx-Mark The highest number mark in the reception queue. Hello-Q The queue, for transmission or reception, for the hello packets. LSR-Q The queue, for transmission or reception, for the link state request packets. Other-Q The queue, for transmission or reception, for the link state acknowledgement, database description, and update packets.
PAGE 1105
Example Dell#show ip ospf 1 statistics global OSPF Packet Count Total Error Hello DDiscr LSReq LSUpd LSAck RX 10 0 8 2 0 0 0 TX 10 0 10 0 0 0 0 OSPF Global Queue Length TxQ-Len RxQ-Len Hello-Q 0 0 LSR-Q 0 0 Other-Q 0 0 Tx-Mark 0 0 0 Rx-Mark 2 0 0 Error packets (Only for RX) Intf-Down Wrong-Len Auth-Err Version No-Buffer Q-OverFlow 0 0 0 0 0 0 Non-Dr Invld-Nbr MD5-Err AreaMis Seq-No Unkown-Pkt 0 0 0 0 0 0 Self-Org 0 Nbr-State 0 Chksum 0 Conf-Issues 0 Socket 0 Error packets (Only for TX) Socket Error
PAGE 1106
Dell(conf-if-te-0/6)# Related Commands clear ip ospf statistics — clears the packet statistics in all interfaces and neighbors. show ip ospf timers rate-limit Show the LSA currently in the queue waiting for timers to expire. Z9000 Syntax Parameters show ip ospf [process-id] timers rate-limit process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process.
PAGE 1107
show ip ospf topology Display routers in directly connected areas. Z9000 Syntax Parameters show ip ospf [process-id] topology process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1108
summary-address To advertise one external route, set the OSPF ASBR. Z9000 Syntax summary-address ip-address mask [not-advertise] [tag tag-value] To disable summary address, use the no summary-address ip-address mask command. Parameters ip-address Specify the IP address in dotted decimal format of the address to summarize. mask Specify the mask in dotted decimal format of the address to summarize.
PAGE 1109
With the not-advertise parameter configured, you can use this command to filter out some external routes. For example, if you want to redistribute static routes to OSPF, but you don't want OSPF to advertise routes with prefix 1.1.0.0, you can configure the summary-address 1.1.0.0 255.255.0.0 not-advertise to filter out all the routes fall in range 1.1.0.0/16. Related Commands area range — summarizes routes within an area.
PAGE 1110
pre-Version 6.1.1.1 Usage Information Introduced on the E-Series. Setting the delay and holdtime parameters to a low number enables the switch to an alternate path quickly but requires more CPU usage. timers throttle lsa all Configure LSA transmit intervals. Z9000 Syntax timers throttle lsa all {start-interval | hold-interval | maxinterval} To return to the default, use the no timers throttle lsa command.
PAGE 1111
Usage Information LSAs are sent after the start-interval and then after hold-interval until the maximum interval is reached. In throttling, exponential backoff is used when sending same LSA, so that the interval is multiplied until the maximum time is reached. For example, if the start-interval 5000 and hold-interval 1000 and max-interval 100,000, the LSA is sent at 5000 msec, then 1000 msec, then 2000 msec, them 4000 until 100,000 msec is reached.
PAGE 1112
area authentication Configure an IPsec authentication policy for OSPFv3 packets in an OFSPFv3 area. Z-Series Syntax Parameters area area-id authentication ipsec spi number {MD5 | SHA1} [keyencryption-type] key area area-id Area for which OSPFv3 traffic is to be authenticated. For area-id, you can enter a number. The range is from 0 to 4294967295. ipsec spi number Security Policy index (SPI) value that identifies an IPsec security policy. The range is from 256 to 4294967295.
PAGE 1113
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.4.2.0 Introduced on the E-Series TeraScale. Before you enable IPsec authentication on an OSPFv3 area, you must first enable OSPFv3 globally on the router. Configure the same authentication policy (same SPI and key) on each interface in an OSPFv3 link. An SPI number must be unique to one IPsec security policy (authentication or encryption) on the router.
PAGE 1114
esp encryptionalgorithm Encryption algorithm used with ESP. Valid values are: 3DES, DES, AES-CBC, and NULL. For AES-CBC, only the AES-128 and AES-192 ciphers are supported. keyencryptionalgorithm (OPTIONAL) Specifies if the key is encrypted. key Text string used in encryption. Valid values: 0 (key is not encrypted) or 7 (key is encrypted).
PAGE 1115
Usage Information Version 9.1. (0.0) Introduced on the S4810 and Z9000. Version 8.4.2.0 Introduced on the E-Series TeraScale. Version 8.3.19.0 Introduced on the S4820T. Before you enable IPsec encryption on an OSPFv3 interface, first enable OSPFv3 globally on the router. Configure the same encryption policy (same SPI and keys) on each interface in an OSPFv3 link. An SPI value must be unique to one IPsec security policy (authentication or encryption) on the router.
PAGE 1116
Version 9.1. (0.0) Introduced on the S4810 and Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 7.8.1.0 Added support for C-Series. Version 7.4.1.0 Introduced on the E-Series. debug ipv6 ospf bfd Display debug information and interface types for bidirectional forwarding detection (BFD) on OSPF IPv6 packets.
PAGE 1117
Example Lines Beginning With or Including Description OSPFv3... Debugging is on for all OSPFv3 packets and all interfaces. 05:21:01 Displays the time stamp. Sending Ver:3 Sending OSPF3 version..
PAGE 1118
• For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a Port Channel interface, enter the keyword portchannel then a number. The range is 1 to 128. • For a tunnel interface, enter the keyword tunnel then a number. The range is 1 to 16383. • For a VLAN, enter the keyword vlan then a number from 1 to 4094. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 1119
Lines Beginning With or Including Description • 2 - database description • 3 - link state request • 4 - link state update • 5 - link state acknowledgement • 7 - external LSA • 8 - link-state advertisement (OSPFv3) • 9 - link local LSA (OSPFv2), Intra-Area-Prefix LSA (OSPFv3) • 11 - grace LSA (OSPFv3) Length: Displays the packet length. Router ID: Displays the OSPF3 router ID. Area ID: Displays the Area ID. Chksum: Displays the OSPF3 checksum.
PAGE 1120
Command Modes ROUTER OSPFv3 Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.1. (0.0) Introduced on the S4810 and Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 7.8.1.0 Added support for C-Series. Version 7.4.1.0 Introduced on the E-Series.
PAGE 1121
Version 8.3.19.0 Usage Information Introduced on the S4820T. By default, OSPFv3 graceful restart is disabled and functions only in a helper role to help restarting neighbor routers in their graceful restarts when it receives a Grace LSA. To enable OSPFv3 graceful restart, enter the ipv6 router ospf command to enter OSPFv3 configuration mode and then configure a grace period using the gracefulrestart grace-period command.
PAGE 1122
Version 8.3.19.0 Usage Information Introduced on the S4820T. OSPFv3 graceful restart supports planned-only and/or unplanned-only restarts. The default is support for both planned and unplanned restarts. • A planned restart occurs when you enter the redundancy force-failover rpm command to force the primary RPM to switch to the backup RPM. During a planned restart, OSPF sends out a Type-11 Grace LSA before the system switches over to the backup RPM.
PAGE 1123
ipv6 ospf authentication Configure an IPsec authentication policy for OSPFv3 packets on an IPv6 interface. Z-Series Syntax Parameters ipv6 ospf authentication {null | ipsec spi number {MD5 | SHA1} [key-encryption-type] key}} null Causes an authentication policy configured for the area to not be inherited on the interface. ipsec spi number Security Policy index (SPI) value that identifies an IPsec security policy. The range is from 256 to 4294967295.
PAGE 1124
An SPI value must be unique to one IPsec security policy (authentication or encryption) on the router. Configure the same authentication policy (same SPI and key) on each OSPFv3 interface in a link. To remove an IPsec authentication policy from an interface, enter the no ipv6 ospf authentication spi number command. To remove null authentication on an interface to allow the interface to inherit the authentication policy configured for the OSPFv3 area, enter the no ipv6 ospf authentication null command.
PAGE 1125
• Passive — The passive system does not initiate a session. It only responds to a request for session initialization from the active system. The default is Active. Defaults See Parameters Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2.0.
PAGE 1126
Usage Information Version 9.1. (0.0) Introduced on the S4810 and Z9000. Version 7.8.1.0 Added support for C-Series. Version 7.4.1.0 Introduced on the E-Series. Version 8.3.19.0 Introduced on the S4820T.
PAGE 1127
Version 7.4.1.0 Introduced on the E-Series. Version 8.3.19.0 Introduced on the S4820T. Usage Information By default, the dead interval is four times longer than the default hello-interval. Related Commands ipv6 ospf hello-interval – specifies the time interval between hello packets. ipv6 ospf encryption Configure an IPsec encryption policy for OSPFv3 packets on an IPv6 interface.
PAGE 1128
keyencryptiontype (OPTIONAL) Specifies if the authentication key is encrypted. key Text string used in authentication. Valid values: 0 (key is not encrypted) or 7 (key is encrypted). For MD5 authentication, the key must be 32 hex digits (nonencrypted) or 64 hex digits (encrypted). For SHA-1 authentication, the key must be 40 hex digits (non-encrypted) or 80 hex digits (encrypted). Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1129
show crypto ipsec sa ipv6 – displays the security associations set up for OSPFv3 interfaces in encryption policies. ipv6 ospf graceful-restart helper-reject Configure an OSPFv3 interface to not act upon the Grace LSAs that it receives from a restarting OSPFv3 neighbor. Z-Series Syntax ipv6 ospf graceful-restart helper-reject To disable the helper-reject role, enter no ipv6 ospf graceful-restart helper-reject. Defaults The helper-reject role is not configured.
PAGE 1130
To return to the default time interval, enter no ipv6 ospf hello—interval. Parameters seconds Enter the time interval in seconds as the time between hello packets. The range is from 1 to 65525 seconds. Defaults 10 seconds (Ethernet). Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1131
Command History Usage Information Version 9.1. (0.0) Introduced on the S4810 and Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 7.8.1.0 Added support for the C-Series. Version 7.4.1.0 Introduced on the E-Series. Setting a priority of 0 makes the router ineligible for election as a Designated Router or Backup Designated Router. Use this command for interfaces connected to multi-access networks, not pointto-point networks. ipv6 router ospf Enable OSPF for IPv6 router configuration.
PAGE 1132
maximum-paths Enable the software to forward packets over multiple paths. Z9000 Syntax maximum-paths number To disable packet forwarding over multiple paths, use the no maximum-paths command. Parameters number Defaults 8 Command Modes ROUTER OSPF Command History Specify the number of paths. The range is from 1 to 64. The default is 8 paths. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.
PAGE 1133
• For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a VLAN, enter the keyword vlan then a number from 1 to 4094. Defaults Enabled, that is sending of routing updates are enabled by default. Command Modes ROUTER OSPF for OSPFv2 ROUTER OSPFv3 for OSPFv3 Command History Usage Information Version 9.1. (0.
PAGE 1134
Parameters bgp as number Enter the keyword bgp then the autonomous system number. The range is from 1 to 65535. connected Enter the keyword connected to redistribute routes from physically connected interfaces. static Enter the keyword static to redistribute manually configured routes. metric metricvalue Enter the keyword metric then the metric value. The range is from 0 to 16777214. The default is 20.
PAGE 1135
Version 9.1. (0.0) Introduced support for OSPFv3 on the S4810 and Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 7.8.1.0 Added support for the C-Series. Version 7.4.1.0 Introduced on the E-Series. Usage Information To redistribute the default route (x:x:x:x::x), use the default-information originate command. Related Commands default-information originate – configures default external route into OSPFv3. router-id Designate a fixed router ID.
PAGE 1136
Usage Information You can configure an arbitrary value in the IP address for each router. However, each router ID must be unique. If this command is used on an OSPFv3 process that is already active (has neighbors), all the neighbor adjacencies are brought down immediately and new sessions are initiated with the new router ID. Related Commands clear ipv6 ospf process – resets an OSPFv3 router process. show crypto ipsec policy Display the configuration of IPsec authentication and encryption policies.
PAGE 1137
Example Dell#show crypto ipsec policy Crypto IPSec client security policy data Policy name : OSPFv3-1-502 Policy refcount : 1 Inbound ESP SPI : 502 (0x1F6) Outbound ESP SPI : 502 (0x1F6) Inbound ESP Auth Key : 123456789a123456789b123456789c12 Outbound ESP Auth Key : 123456789a123456789b123456789c12 Inbound ESP Cipher Key : 123456789a123456789b123456789c123456789d12345678 Outbound ESP Cipher Key : 123456789a123456789b123456789c123456789d12345678 Transform set : esp-3des esp-md5-hmac Crypto IPSec client secu
PAGE 1138
Transform set The set of security protocols and algorithms used in the policy. Inbound AH SPI The authentication header (AH) security policy index (SPI) for inbound and outbound links. Outbound AH SPI Inbound AH Key The AH key for inbound and outbound links. Outbound AH Key show crypto ipsec sa ipv6 Display the IPsec security associations (SAs) used on OSPFv3 interfaces.
PAGE 1139
Version 8.3.19.0 Introduced on the S4820T. Usage Information The show crypto ipsec sa ipv6 command output displays security associations set up for OSPFv3 links in IPsec authentication and encryption policies on the router. Related Commands show crypto ipsec policy – displays the configuration of IPsec authentication and encryption policies.
PAGE 1140
show crypto ipsec sa ipv6 Command Fields Field Description Interface IPv6 interface Link local address IPv6 address of interface IPSecv6 policy name Name of the IPsec security policy applied to the interface. inbound/outbound ah Authentication policy applied to inbound or outbound traffic. inbound/outbound esp Encryption policy applied to inbound or outbound traffic. spi Security policy index number used to identify the policy.
PAGE 1141
Command History Version 9.1. (0.0) Added support for OSPFv3 on the S4810 and Z9000. Version 8.4.2.2 Added support for the display of graceful restart parameters and Type-11 Grace LSAs on E-Series TeraScale routers. Version 8.3.19.0 Introduced on the S4820T. Version 7.8.1.0 Added support for C-Series. Usage Information The show crypto ipsec sa ipv6 command output displays security associations set up for OSPFv3 links in IPsec authentication and encryption policies on the router.
PAGE 1142
Inter Area Pfx LSA Count 1 Inter Area Rtr LSA Count 0 Group Mem LSA Count 0 Type-7 LSA count 0 Intra Area Pfx LSA Count 2 Intra Area TE LSA Count 2 Area 1 database summary Type Count/Status Brd Rtr Count 1 AS Bdr Rtr Count 1 LSA count 8 Rtr LSA Count 1 Net LSA Count 0 Inter Area Pfx LSA Count 5 Inter Area Rtr LSA Count 0 Group Mem LSA Count 0 Type-7 LSA count 0 Intra Area Pfx LSA Count 2 Intra Area TE LSA Count 2 E1200-T2C2#sh ipv6 ospf neighbor Neighbor ID ID Interface 63.114.8.
PAGE 1143
Command History Usage Information Version 9.2. (0.0) Added support for showing BFD status on the S4820T, S4810, and Z9000. Version 9.1. (0.0) Added support for OSPFv3 on the S4810 and Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 7.8.1.0 Added support for the C-Series. Version 7.4.1.0 Introduced on the E-Series. If you enable BFD at the global level, show ipv6 ospf interface shows the BFD provisioning.
PAGE 1144
Defaults none Command Modes EXEC • For a Port Channel interface, enter the keywords portchannel then a number. For the C-Series, Z-Series, and S4810, the range is 1 to 128. • For a VLAN, enter the keyword vlan then the VLAN ID. The range is 1 to 4094. EXEC Privilege Command History Example Version 9.1. (0.0) Introduced support for OSPFv3 on the S4810 and Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 7.8.1.0 Added support for the C-Series. Version 7.4.1.
PAGE 1145
Policy-based Routing (PBR) 35 Policy-based routing (PBR) allows you to apply routing policies to specific interfaces. To enable PBR, create a redirect list and apply it to the interface. After the redirect list is applied to the interface, all traffic passing through the interface is subject to the rules defined in the redirect list. PBR is supported by the Dell Networking Operating System (OS). The commands in this chapter are supported on the Z9000 platform.
PAGE 1146
Related Commands ip redirect-list – enables an IP Redirect List. ip redirect-group Apply a redirect list (policy-based routing) on an interface. You can apply multiple redirect lists to an interface by entering this command multiple times. Z9000 Syntax ip redirect-group redirect-list-name To remove a redirect list from an interface, use the no ip redirect-group name command. Parameters redirect-listname Enter the name of a configured redirect list.
PAGE 1147
• show ip redirect-list – displays the redirect-list configuration. ip redirect-list Configure a redirect list and enter REDIRECT-LIST mode. Z9000 Syntax ip redirect-list redirect-list-name To remove a redirect list, use the no ip redirect-list command. Parameters redirect-listname Defaults none Command Modes CONFIGURATION Command History Enter the name of a redirect list. Version 9.4.0.0 Introduced on the Z9000. Version 8.4.2.1 Introduced on the C-Series and S-Series. Version 8.4.2.
PAGE 1148
Parameters ip-protocolnumber Enter a number from 0 to 255 for the protocol identified in the IP protocol header. protocol-type Enter one of the following keywords as the protocol type: ip for any internet protocol • tcp for transmission control protocol • udp for user datagram protocol Enter the IP address of the network or host from which the packets were sent. mask Enter a network mask in /prefix format (/x). any Enter the keyword any to specify that all traffic is subject to the filter.
PAGE 1149
Version 8.4.2.1 Introduced on the C-Series and S-Series. Version 8.4.2.0 Introduced on the E-Series TeraScale. Version 7.5.1.0 Introduced on the E-Series ExaScale. redirect Configure a rule for the redirect list.
PAGE 1150
source Enter the IP address of the network or host from which the packets were sent. mask Enter a network mask in /prefix format (/x). any Enter the keyword any to specify that all traffic is subject to the filter. host ip-address Enter the keyword host then the IP address to specify a host IP address. destination Enter the IP address of the network or host to which the packets are sent. operator (OPTIONAL) For TCP and UDP parameters only.
PAGE 1151
Parameters sequencenumber Enter a number from 1 to 65535. permit Enter the keyword permit assign the sequence to the permit list. redirect Enter the keyword redirect to assign the sequence to the redirect list. ip-address Enter the IP address of the forwarding router. ip-protocolnumber Enter the keyword ip-protocol-number then the number from 0 to 255 for the protocol identified in the IP protocol header.
PAGE 1152
• source port Enter the keywords source-port then the port number to be matched in the ACL rule in the ICAP rule destinationport Enter the keywords destination-port then the port number to be matched in the ACL rule in the ICAP rule. source-portrange Enter the keywords Source-port-range then the range of the start port to end port to be matched in the ACL rule in the ICAP rule.
PAGE 1153
Command History Version 9.4. (0.0) Added support for removing SONET interface on the S6000, S4810, S4820T and Z9000 platforms. Version 7.4.1.0 Introduced. Usage Information The show cam pbr command displays the PBR CAM content.
PAGE 1154
Command Modes Command History Example • EXEC • EXEC Privilege Version 9.4. (0.0) Added support for removing SONET interface on the S6000, S4810, S4820T and Z9000 platforms. Dell#show ip redirect-list IP redirect-list ecmp: Defined as: seq 5 redirect 100.1.1.
PAGE 1155
PIM-Sparse Mode (PIM-SM) 36 The protocol-independent multicast (PIM) commands are supported by the Dell Networking operating software on the Z-Series platform. IPv4 PIM-Sparse Mode Commands The following describes the IPv4 PIM-sparse mode (PIM-SM) commands. clear ip pim rp-mapping The bootstrap router (BSR) feature uses this command to remove all or particular rendezvous point (RP) advertisement.
PAGE 1156
clear ip pim tib Clear PIM tree information from the PIM database. Z9000 Syntax Parameters clear ip pim tib [group] group (OPTIONAL) Enter the multicast group address in dotted decimal format (A.B.C.D). Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1157
To disable PIM debugging, use the no debug ip pim command or use the undebug all to disable all debugging command. Parameters bsr (OPTIONAL) Enter the keyword bsr to view PIM Candidate RP/BSR activities. events (OPTIONAL) Enter the keyword group to view PIM messages for a specific group. group (OPTIONAL) Enter the keyword group to view PIM messages for a specific group. packet [in | out] (OPTIONAL) Enter the keyword packet to view PIM packets.
PAGE 1158
Version 7.8.1.0 Introduced on the S-Series. ip pim bsr-border Define the border of PIM domain by filtering inbound and outbound PIM-BSR messages per interface. Z9000 Syntax ip pim bsr-border To return to the default value, use the no ip pim bsr-border command. Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1159
• For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a VLAN, enter the keyword vlan then a number from 1 to 4094. hash-masklength (OPTIONAL) Enter the hash mask length. The range is from zero (0) to 32. The default is 30. priority (OPTIONAL) Enter the priority used in Bootstrap election process. The range is from zero (0) to 255.
PAGE 1160
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.
PAGE 1161
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.8.1.0 Introduced on the C-Series for the port-channels and the SSeries. Version 7.7.1.0 Introduced on the E-Series. Example Dell(conf)# ip access-list extended iptv-channels Dell(config-ext-nacl)# permit ip 10.1.2.3/24 225.1.1.
PAGE 1162
Example Dell(conf)# ip access-list standard map1 Dell(config-std-nacl)# permit 224.0.0.1/24 Dell(config-std-nacl)#exit Dell(conf)#int gig 1/1 Dell(config-if-gi-1/1)# ip pim ingress-interface-map map1 ip pim neighbor-filter To prevent a router from participating in protocol independent multicast (PIM), configure this feature. Z9000 Syntax ip pim neighbor-filter {access-list} To remove the restriction, use the no ip pim neighbor-filter {accesslist} command.
PAGE 1163
ip pim query-interval Change the frequency of PIM Router-Query messages. Z9000 Syntax ip pim query-interval seconds To return to the default value, use the no ip pim query-interval seconds command. Parameters seconds Enter a number as the number of seconds between router query messages. The range is from 0 to 65535. The default is 30 seconds. Defaults 30 seconds Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1164
Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810.
PAGE 1165
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.
PAGE 1166
priority (OPTIONAL) Enter the priority used in Bootstrap election process. The range is zero (0) to 255. The default is 192. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.
PAGE 1167
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.8.1.0 Introduced on the C-Series for the port-channels and the SSeries. The interface must be enabled (the no shutdown command) and not have the switchport command configured. Multicast must also be enabled globally (using the ip multicast-lag-hashing command).
PAGE 1168
Usage Information Version 7.8.1.0 Introduced on the C-Series for the port-channels and the SSeries. Version 7.7.1.1 Introduced This command configures an expiration timer for all S.G entries, unless they are assigned to an Extended ACL. ip pim spt-threshold To switch to the shortest path tree when the traffic reaches the specified threshold value, configure the PIM router. Syntax ip pim spt-threshold value | infinity To return to the default value, use the no ip pim spt-threshold command.
PAGE 1169
no ip pim snooping dr-flood Disable the flooding of multicast packets to the PIM designated router. Syntax no ip pim snooping dr-flood To re-enable the flooding of multicast packets to the PIM designated router, use the ip pim snooping dr-flood command. Defaults Enabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1170
show ip pim bsr-router View information on the Bootstrap router. Z9000 Syntax show ip pim bsr-router Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.
PAGE 1171
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.1.1.0 Introduced on the E-Series ExaScale.
PAGE 1172
172.21.110.1 172.21.203.1 Gi 13/6 Gi 13/7 v2/S 0 v2/S 0 30 1 30 1 172.21.110.1 172.21.203.1 show ip pim neighbor View PIM neighbors. Z9000 Syntax show ip pim neighbor Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.
PAGE 1173
Field Example Description • 1 = default Designated Router priority (use the ip pim dr-priority command) • DR = Designated Router • S = Sparse mode Dell#show ip pim neighbor Neighbor Interface Uptime/Expires Ver Address 127.87.3.4 Gi 7/16 09:44:58/00:01:24 v2 Dell# DR Prio/Mode 1 / S show ip pim rp View all multicast groups-to-RP mappings.
PAGE 1174
224.2.217.146 224.3.3.3 225.1.2.1 225.1.2.2 229.1.2.1 229.1.2.2 Dell# Example (Mapping) 165.87.20.4 165.87.20.4 165.87.20.4 165.87.20.4 165.87.20.4 165.87.20.4 Dell#sh ip pim rp mapping Group(s): 224.0.0.0/4 RP: 165.87.20.4, v2 Info source: 165.87.20.5, via bootstrap, priority 0 Uptime: 00:03:11, expires: 00:02:46 RP: 165.87.20.3, v2 Info source: 165.87.20.5, via bootstrap, priority 0 Uptime: 00:03:11, expires: 00:03:03 Dell# Example (Address) Dell#sh ip pim rp 229.1.2.1 Group RP 229.1.2.1 165.87.20.
PAGE 1175
Usage Information Example (#2) The following describes the show ip pim snooping interface commands shown in the following example. Field Description Interface Displays the VLAN interfaces with PIM-SM snooping enabled. Ver/Mode Displays the PIM version number for each VLAN interface with PIM-SM snooping enabled: • v2 = PIM version 2 • S = PIM Sparse mode Nbr Count Displays the number of neighbors learned through PIM-SM snooping on the interface.
PAGE 1176
Usage Information Version 8.3.12.0 Introduced on the S4810. Version 8.4.1.1 Introduced on the E-Series ExaScale. The following describes the show ip pim snooping neighbor commands shown in the following example. Field Description Neighbor address Displays the IP address of the neighbor learned through PIM-SM snooping. Interface Displays the VLAN ID number and slot/port on which the PIM-SM-enabled neighbor was discovered.
PAGE 1177
group-address (OPTIONAL) Enter the group address in dotted decimal format (A.B.C.D) to display TIB information PIM-SM snooping discovered for a specified multicast group. source-address (OPTIONAL) Enter the source address in dotted decimal format (A.B.C.D) to display TIB information PIM-SM snooping discovered for a specified multicast source. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific.
PAGE 1178
Field Description • Example K=acknowledge pending state Incoming interface Displays the reverse path forwarding (RPF) interface towards the RP/ source. RPF neighbor Displays the next hop from this interface towards the RP/ source.
PAGE 1179
• Command History EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.4.1.1 Support for the display of PIM-SM snooping status was added on E-Series ExaScale.
PAGE 1180
Memory usage: TIB Nexthop cache Interface table Neighbor table RP Mapping : : : : : 3768 bytes 0 bytes 992 bytes 528 bytes 0 bytes show ip pim tib View the PIM tree information base (TIB). Z9000 Syntax Parameters show ip pim tib [group-address [source-address]] group-address (OPTIONAL) Enter the group address in dotted decimal format (A.B.C.D). source-address (OPTIONAL) Enter the source address in dotted decimal format (A.B.C.D).
PAGE 1181
Example Field Description expires Displays the amount of time until the entry expires and is removed from the database. RP Displays the IP address of the RP/source for this entry.
PAGE 1182
Incoming interface: GigabitEthernet 4/23, RPF neighbor 10.211.1.2 Outgoing interface list: GigabitEthernet 8/0 (*, 226.1.1.3), uptime 00:18:08, expires 00:00:52, RP 10.211.2.1, flags: SCJ Incoming interface: GigabitEthernet 4/23, RPF neighbor 10.211.1.2 Outgoing interface list: GigabitEthernet 8/0 (*, 226.1.1.4), uptime 00:18:08, expires 00:00:52, RP 10.211.2.1, flags: SCJ Incoming interface: GigabitEthernet 4/23, RPF neighbor 10.211.1.
PAGE 1183
ipv6 pim bsr-border Invoke IPv6 PIM debugging. Syntax debug ipv6 pim [bsr | events | group group | packet | register [group] | state | | timer [assert | hello | joinprune | register]] To disable IPv6 PIM debugging, use the no debug ipv6 pim command. Parameters bsr (OPTIONAL) Enter the keyword bsr to invoke debugging of IPv6 PIM Candidate RP/BSR activities. events (OPTIONAL) Enter the keyword events to invoke debugging of IPv6 PIM events.
PAGE 1184
Version 8.3.12.0 Introduced on the S4810. Version 7.4.1.0 Introduced ipv6 pim bsr-candidate Configure the router as a bootstrap (BSR) candidate. Syntax ipv6 pim bsr-candidate interface [hash-mask-length] [priority] To disable the bootstrap candidate, use the no ipv6 pim bsr-candidate command. Parameters interface Enter the following keywords and slot/port or number information: • For a Loopback interface, enter the keyword loopback then a number from 0 to 16383.
PAGE 1185
ipv6 pim dr-priority Change the designated router (DR) priority for the IPv6 interface. Syntax ipv6 pim dr-priority priority-value To remove the DR priority value assigned, use the no ipv6 pim dr-priority command. Parameters priority-value Enter a number. Preference is given to larger/higher number. The range is from 0 to 4294967294. The default is 1. Defaults 1 Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1186
Defaults none Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 7.3.1.
PAGE 1187
Version 8.3.1.0 Usage Information Introduced Do not enter this command before creating the access-list. ipv6 pim query-interval Change the frequency of IPv6 PIM router-query messages. Syntax ipv6 pim query-interval seconds To return to the default value, use the no ipv6 pim query-interval seconds command. Parameters seconds Enter a number as the number of seconds between router query messages. The range is from 0 to 65535. The default is 30 seconds.
PAGE 1188
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.1.
PAGE 1189
Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 7.4.1.0 Introduced The RP addresses are stored in the order in which they are entered.
PAGE 1190
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 7.4.1.0 Introduced ipv6 pim sparse-mode Enable IPv6 PIM sparse mode on the interface.
PAGE 1191
ipv6 pim spt-threshold Specifies when a PIM leaf router should join the shortest path tree. Syntax ipv6 pim spt-threshold {kbps | infinity} To return to the default value, use the no ipv6 pim spt-threshold command. Parameters kbps Enter a traffic rate in kilobytes per second. The range is from 0 to 4294967 kbps. The default is 10 kbps. infinity Enter the keyword infinity to have all sources for the specified group use the shared tree and never join shortest path tree (SPT).
PAGE 1192
The following is a list of the Dell Networking OS version history for this command. Example Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 7.4.1.
PAGE 1193
DR : this router Dell# show ipv6 pim neighbor Displays IPv6 PIM neighbor information. Syntax Parameters show ipv6 pim neighbor [detail] detail (OPTIONAL) Enter the keyword detail to displayed PIM neighbor detailed information. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1194
NOTE: The :: notation specifies successive hexadecimal fields of zero. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 7.4.1.
PAGE 1195
NOTE: The :: notation specifies successive hexadecimal fields of zero. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 7.4.1.
PAGE 1196
PAGE 1197
37 Port Monitoring The port monitoring feature allows you to monitor network traffic by forwarding a copy of each incoming or outgoing packet from one port to another port. The commands in this chapter are supported on the Z9000 platform. Important Points to Remember • Port monitoring is supported on physical ports and logical interfaces, such as Port Channels and virtual local area networks (VLANs). • The monitoring (destination, “MG”) and monitored (source, “MD”) ports must be on the same switch.
PAGE 1198
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.
PAGE 1199
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4(0.0) Added support for the rpm/erpm option on the Z9000. Version 9.0.2.0 Introduced on the S6000. Version 9.0.2.0 Introduced on the MXL. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.
PAGE 1200
Example Version 8.3.7.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.7.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced on the E-Series.
PAGE 1201
Example Related Commands Version 8.3.19.0 Introduced on the S4820T. Version 8.3.7.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.7.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced on the E-Series.
PAGE 1202
The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.7.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced on the E-Series.
PAGE 1203
• For a VLAN interface enter the keyword VLAN followed by a number from 1 to 4094. • For a port channel interface, enter the keyword portchannel followed by the port-channel id . range Enter the keyword range to specify the list of interfaces. destination Enter the keyword destination to specify the destination interface. interface direction {rx | tx | both} • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 1204
Example 1204 Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.7.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced on the E-Series.
PAGE 1205
Private VLAN (PVLAN) 38 The private VLAN (PVLAN) feature of the Dell Networking operating software is supported on the Z9000 platforms. Private VLANs extend the Dell Networking OS security suite by providing Layer 2 isolation between ports within the same private VLAN. A private VLAN partitions a traditional VLAN into subdomains identified by a primary and secondary VLAN pair. The Dell Networking OS private VLAN implementation is based on RFC 3069. For more information, refer to the following commands.
PAGE 1206
Port Types: • Community port: A community port is a port that belongs to a community VLAN and is allowed to communicate with other ports in the same community VLAN and with promiscuous ports. • Isolated port: An isolated port is a port that, in Layer 2, can only communicate with promiscuous ports that are in the same PVLAN. • Promiscuous port: A promiscuous port is a port that is allowed to communicate with any other port type.
PAGE 1207
Related Commands Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the C-Series and S-Series. private-vlan mode — sets the mode of the selected VLAN to community, isolated, or primary. private-vlan mapping secondary-vlan — maps secondary VLANs to the selected primary VLAN. show arp — displays the ARP table. switchport mode private-vlan — sets PVLAN mode of the selected port.
PAGE 1208
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the C-Series and S-Series. The VLAN: • can be in only one mode, either community, isolated, or primary. • mode ode to community or isolated even before associating it to a primary VLAN. This secondary VLAN continues to work normally as a normal VLAN even though it is not associated to a primary VLAN.
PAGE 1209
Command Modes INTERFACE VLAN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.
PAGE 1210
Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.
PAGE 1211
Per-VLAN Spanning Tree Plus (PVST+) 39 The Dell Networking operating software implementation of per-VLAN spanning tree plus (PVST+) is based on the IEEE 802.1w standard spanning tree protocol. Dell Networking OS supports PVST+ on the Z9000 platform. NOTE: For easier command line entry, the plus (+) sign is not used at the command line. description Enter a description of the PVST+. Z9000 Syntax description {description} To remove the description, use the no description {description} command.
PAGE 1212
Related Commands protocol spanning-tree pvst — enter SPANNING TREE mode on the switch. disable Disable PVST+ globally. Z9000 Syntax disable To enable PVST+, use the no disable command. Defaults Disabled. Command Modes CONFIGURATION (conf-pvst) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1213
extend system-id To augment the Bridge ID with a VLAN ID so that PVST+ differentiate between BPDUs for each VLAN, use extend system ID. If the VLAN receives a BPDU meant for another VLAN, PVST+ does not detect a loop, and both ports can remain in Forwarding state. Z9000 Syntax extend system-id Defaults Disabled Command Modes PROTOCOL PVST Command History This guide is platform-specific.
PAGE 1214
protocol spanning-tree pvst To enable PVST+ on a device, enter the PVST+ mode. Z9000 Syntax protocol spanning-tree pvst To disable PVST+, use the disable command. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
PAGE 1215
show spanning-tree pvst View the Per-VLAN spanning tree configuration. Z9000 Syntax Parameters show spanning-tree pvst [vlan vlan-id] [brief] [guard] vlan vlan-id (OPTIONAL) Enter the keyword vlan then the VLAN ID. The range is 1 to 4094. brief (OPTIONAL) Enter the keyword brief to view a synopsis of the PVST+ configuration information.
PAGE 1216
Usage Information Example (Brief) Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.4.1.0 Expanded to display port error disable state (EDS) caused by loopback BPDU inconsistency and Port VLAN ID inconsistency. Version 6.2.1.1 Introduced. The following describes the show spanning-tree pvst command shown in the following examples. Field Description Interface Name PVST interface. Instance PVST instance.
PAGE 1217
Number of topology changes 3, last change occured 00:57:00 Port 130 (GigabitEthernet 1/0) is designated Forwarding Port path cost 20000, Port priority 128, Port Identifier 128.130 Designated root has priority 4096, address 0001.e805.e3:06 Designated bridge has priority 4096, address 0001.e805.e3:06 Designated port id is 128.
PAGE 1218
Edge port:no (default) port guard :none (default) Link type: point-to-point (auto) bpdu filter:disable (default) Bpdu guard :disable (default) Bpdus sent 1, received 0 Interface Designated Name PortID Prio Cost Sts Cost Bridge ID PortID --------------------------------------------------------Gi 1/0 128.1223 128 20000 EDS 0 32768 0001.e800.a12b 128.
PAGE 1219
vlan vlan-range Enter the keyword vlan then the VLAN numbers. The range is from 1 to 4094. cost number Enter the keyword cost then the port cost value. The range is from 1 to 200000. Defaults: • 100 Mb/s Ethernet interface = 200000. • 1-Gigabit Ethernet interface = 20000. • 10-Gigabit Ethernet interface = 2000. • Port Channel interface with one 100 Mb/s Ethernet = 200000. • Port Channel interface with one 1 Gigabit Ethernet = 20000. • Port Channel interface with one 10 Gigabit Ethernet = 2000.
PAGE 1220
Usage Information Version 8.2.1.0 Introduced the hardware shutdown-on-violation option. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Added the optional Bridge Port Data Unit (BPDU) guard. Version 6.2.1.1 Introduced. The BPDU guard option prevents the port from participating in an active STP topology in case a BPDU appears on a port unintentionally, or is misconfigured, or is subject to a DOS attack.
PAGE 1221
Related Commands show spanning-tree pvst — views the PVST+ configuration. spanning-tree pvst err-disable Place ports in an Err-Disabled state if they receive a PVST+ BPDU when they are members an untagged VLAN. Z9000 Syntax spanning-tree pvst err-disable cause invalid-pvst-bpdu Defaults Enabled; ports are placed in the Err-Disabled state if they receive a PVST+ BPDU when they are members of an untagged VLAN. Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1222
tc-flush-standard Enable the MAC address flushing after receiving every topology change notification. Z-Series Syntax tc-flush-standard To disable, use the no tc-flush-standard command. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1223
Parameters vlan vlan-range Enter the keyword vlan then the VLAN numbers. The range is from 1 to 4094. bridge-priority value Enter the keywords bridge-priority then the bridge priority value in increments of 4096. The range is from 0 to 61440. The default is 32768. Defaults 32768 Command Modes CONFIGURATION (conf-pvst) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1224
Parameters vlan vlan-range Enter the keyword vlan then the VLAN numbers. The range is from 1 to 4094. forward-delay seconds Enter the keywords forward-delay then the time interval, in seconds, that Dell Networking OS waits before transitioning PVST+ to the forwarding state. The range is from 4 to 30 seconds. The default is 15 seconds. Defaults 15 seconds Command Modes CONFIGURATION (conf-pvst) Command History This guide is platform-specific.
PAGE 1225
Parameters vlan vlan-range Enter the keyword vlan then the VLAN numbers. The range is from 1 to 4094. hello-time seconds Enter the keywords hello-time then the time interval, in seconds, between transmission of BPDUs. The range is from 1 to 10 seconds. The default is 2 seconds. Defaults 2 seconds Command Modes CONFIGURATION (conf-pvst) Command History This guide is platform-specific.
PAGE 1226
Parameters vlan vlan-range Enter the keyword vlan then the VLAN numbers. The range is from 1 to 4094. max-age seconds Enter the keywords max-age then the time interval, in seconds, that Dell Networking OS waits before refreshing configuration information. The range is from 6 to 40 seconds. The default is 20 seconds. Defaults 20 seconds Command Modes CONFIGURATION (conf-pvst) Command History This guide is platform-specific.
PAGE 1227
Quality of Service (QoS) 40 The Dell Networking operating software commands for quality of service (QoS) include traffic conditioning and congestion control. QoS commands are not universally supported on all Dell Networking Products.Z9000 platform. This chapter contains the following sections: • Global Configuration Commands • Per-Port QoS Commands • Policy-Based QoS Commands Global Configuration Commands There is only one global configuration QoS command.
PAGE 1228
Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Introduced. Per-Port QoS Commands Per-port QoS (port-based QoS) allows you to define the QoS configuration on a per-physical-port basis. dot1p-priority Assign a value to the IEEE 802.1p bits on the traffic this interface receives. Z9000 Syntax dot1p-priority priority-value To delete the IEEE 802.1p configuration on the interface, use the no dot1ppriority command.
PAGE 1229
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series. The dot1p-priority command changes the priority of incoming traffic on the interface. The system places traffic marked with a priority in the correct queue and processes that traffic according to its queue.
PAGE 1230
The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Added the kbps option on the C-Series, E-Series, and SSeries. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series.
PAGE 1231
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.
PAGE 1232
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.1 Introduced on the S4810. Version 8.2.1.0 Introduced on the C-Series and S-Series. Guarantee a minimum bandwidth to different queues globally using the serviceclass bandwidth-weight command from CONFIGURATION mode. The command is applied in the same way as the bandwidth-weight command in an output QoS policy.
PAGE 1233
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Usage Information To apply dot1p-queue-mapping, use the service-class dynamic dot1p command. Related Commands show qos dot1p-queue-mapping — displays the dot1p priority to queue mapping on the switch. service-class dynamic dot1p Honor all 802.
PAGE 1234
assigned to the port channel are automatically configured; you cannot assign the service-class dynamic command to individual interfaces in a port channel. • All dot1p traffic is mapped to Queue 0 unless you enable the service-class dynamic dot1p command on an interface or globally. • Layer 2 or Layer 3 service policies supersede dot1p service classes. strict-priority queue Configure a unicast queue as a strict-priority (SP) queue.
PAGE 1235
Policy-Based QoS Commands Policy-based traffic classification is handled with class maps. These maps classify unicast traffic into one of eight classes in S-Series or eight classes in case of S6000. Dell Networking OS enables you to match multiple class maps and specify multiple match criteria. Policy-based QoS is not supported on logical interfaces, such as port-channels, VLANS, or loopbacks. bandwidth-percentage Assign a percentage of weight to the class/queue.
PAGE 1236
class-map Create/access a class map. Class maps differentiate traffic so that you can apply separate quality-ofservice policies to each class. Z9000 Syntax Parameters class-map {match-all | match-any} class-map-name [cpu-qos] [layer2] match-all Determines how packets are evaluated when multiple match criteria exist. Enter the keywords match-all to determine that the packets must meet all the match criteria in order to be a member of the class.
PAGE 1237
Usage Information Packets arriving at the input interface are checked against the match criteria and configured using this command to determine if the packet belongs to that class. This command accesses CLASS-MAP mode, where the configuration commands include thematch ip and match mac options. Related Commands ip access-list extended — configures an extended IP ACL. ip access-list standard — configures a standard IP ACL.
PAGE 1238
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.18.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.
PAGE 1239
Related Commands Version 8.3.7.0 Introduced on the S4810. pre-Version 7.7.1.0 Introduced. policy-map-input — creates an input policy map. policy-map-output — creates an output policy map. qos-policy-input — creates an input QoS-policy on the router. qos-policy-output — creates an output QoS-policy on the router. wred-profile — creates a WRED profile. match ip access-group Configure match criteria for a class map, based on the access control list (ACL).
PAGE 1240
Version 8.3.7.0 Introduced on the S4810. Usage Information To access this command, enter the class-map command. After the class map is identified, you can configure the match criteria. For class-map match-any, a maximum of five ACL match criteria are allowed. For class-map match-all, only one ACL match criteria is allowed. Related Commands class-map — identifies the class map. match ip dscp Use a differentiated services code point (DSCP) value as a match criteria.
PAGE 1241
The match ip dscp and match ip precedence commands are mutually exclusive. Up to 64 IP DSCP values can be matched in one match statement. For example, to indicate IP DCSP values 0 1 2 3 4 5 6 7, enter either the match ip dscp 0,1,2,3,4,5,6,7 or match ip dscp 0-7 command. NOTE: Only one of the IP DSCP values must be a successful match criterion, not all of the specified IP DSCP values must match. Related Commands class-map — identifies the class map.
PAGE 1242
Usage Information To access this command, enter the class-map command. After the class map is identified, you can configure the match criteria. The match ip precedence command and the match ip dscp command are mutually exclusive. Up to eight precedence values can be matched in one match statement. For example, to indicate the IP precedence values 0 1 2 3, enter either the match ip precedence 0-3 or match ip precedence 0,1,2,3 command.
PAGE 1243
Usage Information To access this command, enter the class-map command. After the class map is identified, you can configure the match criteria. Related Commands class-map — identifies the class map. match mac dot1p Configure a match criterion for a class map based on a dot1p value. Z9000 Syntax match mac dot1p {dot1p-list} Parameters dot1p-list Enter a dot1p value. The range is from 0 to 7. Defaults none Command Modes CLASS-MAP Command History This guide is platform-specific.
PAGE 1244
Parameters number Enter the VLAN ID. The range is from 1 to 4094. Defaults none Command Modes CLASS-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.
PAGE 1245
The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Policy name character limit increased from 16 to 32. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series.
PAGE 1246
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. The input policy map is used to classify incoming traffic to different flows using class-map, QoS policy, or incoming packets DSCP. This command enables PolicyMap-Input Configuration mode (conf-policy-map-in).
PAGE 1247
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Policy name character limit increased from 16 to 32. Version 7.6.1.0 Introduced on the C-Series and S-Series. pre-Version 6.1.1.1 Introduced on the E-Series. Usage Information To assign traffic to different flows using QoS policy, use the Output Policy map. This command enables Policy-Map-Output Configuration mode (conf-policymap-out).
PAGE 1248
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Use this command to specify the name of the input QoS policy. Once input policy is specified, rate-police can be defined. This command enables the qos-policyinput configuration mode— (conf-qos-policy-in).
PAGE 1249
Usage Information Version 8.2.1.0 Policy name character limit increased from 16 to 32. Version 7.6.1.0 Introduced on the C-Series and S-Series. pre-Version 6.1.1.1 Introduced on the E-Series. Use this command to specify the name of the output QoS policy. Once output policy is specified, rate-shape, scheduler strict, bandwidth-percentage, and WRED can be defined. This command enables the qos-policy-output configuration mode —(conf-qos-policy-out).
PAGE 1250
multicastbandwidth percentage (OPTIONAL) Enter the keywords multicast-bandwidth then the bandwidth percentage. The range is from 0 to 100%. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 8.3.19.0 Introduced on the S4820T.
PAGE 1251
queue ingress Assign a WRED Curve to all eight ingress Multicast queues or designate the percentage for the Multicast bandwidth queue. Syntax queue ingress multicast {linecard slot number port-set number | all} [wred-profile name] To return to the default, use the no queue ingress multicast {linecard slot number port-set number | all} [wred-profile name] command. Parameters linecard number Enter the keyword linecard then the line card slot number.
PAGE 1252
NOTE: The multicast-bandwidth option is not supported on queue ingress. If you attempt to use the multicast-bandwidth option, the following reject error message is generated: % Error:Bandwidth-percent is not allowed for ingress multicast. rate-police Specify the policing functionality on incoming traffic. Z9000 Syntax Parameters rate-police [kbps] committed-rate [burst-KB] [peak [kbps] peakrate [burst-KB]] kbps Enter the keyword kbps to specify the rate limit in Kilobits per second (Kbps).
PAGE 1253
Related Commands rate police — specifies traffic policing on the selected interface. qos-policy-input — creates a QoS output policy. rate-shape Shape traffic output as part of the designated policy. Z9000 Syntax Parameters rate-shape [kbps] rate [burst-KB] kbps Enter the keyword kbps to specify the rate limit in Kilobits per second (Kbps). Make the following value a multiple of 64. The range is from 0 to 40000000. The default granularity is Megabits per second (Mbps).
PAGE 1254
To remove the input policy map from the interface, use the no service-policy input policy-map-name [layer2] command. Parameters policy-mapname Enter the name for the policy map in character format (32 characters maximum). You can identify an existing policy map or name one that does not yet exist. layer2 (OPTIONAL) Enter the keyword layer2 to specify a Layer 2 Class Map. The default is Layer 3. Defaults Layer 3 Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1255
Parameters policy-mapname Enter the name for the policy map in character format (32 characters maximum). You can identify an existing policy map or name one that does not yet exist. Defaults none Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.
PAGE 1256
qos-policy qos-policyname (OPTIONAL) Enter the keywords qos-policy then the QoS policy name assigned to the queue in text format (16 characters maximum). This specifies the input QoS policy assigned to the queue under policy-map-input and output QoS policy under policy-map-output context. Defaults none Command Modes CONFIGURATION (conf-policy-map-in and conf-policy-map-out) Command History This guide is platform-specific.
PAGE 1257
Command Modes CONFIGURATION (conf-qos-policy-in) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810.
PAGE 1258
Related Commands class-map — identifies the class map. show qos dot1p-queue-mapping Displays the dot1p priority to queue mapping on the switch. Syntax Defaults show qos dot1p-queue-mapping • dot1p Priority: 0 1 2 3 4 5 6 7 • Queue: 2 0 1 3 4 5 6 7 Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1259
detail interface To view a policy map interface in detail, enter the keyword detail and optionally one of the following keywords and slot/port or number information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific.
PAGE 1260
5 6 7 Dell# Example (Summary IPv4) c5 c6 c7 q6 q7 Dell#sho qos policy-map summary Interface policy-map-input policy-map-output Gi 4/1 PM1 Gi 4/2 PM2 PMOut Dell# show qos policy-map-input View the input QoS policy map details. Z9000 Syntax Parameters show qos policy-map-input [policy-map-name] [class class-mapname] [qos-policy-input qos-policy-name] policy-mapname Enter the policy map name. class classmap-name Enter the keyword class then the class map name.
PAGE 1261
pre-Version 6.1.1.1 Example Introduced on the E-Series. Dell#show qos policy-map-input Policy-map-input PolicyMapInput Aggregate Qos-policy-name AggPolicyIn Queue# Class-map-name Qos-policy-name 0 ClassMap1 qosPolicyInput Dell# show qos policy-map-output View the output QoS policy map details. Z9000 Syntax Parameters Defaults Command Modes Command History show qos policy-map-output [policy-map-name] [qos-policy-output qos-policy-name] policy-mapname Enter the policy map name.
PAGE 1262
Aggregate Qos-policy-name AggPolicyOut Queue# Qos-policy-name 0 qosPolicyOutput Dell# show qos qos-policy-input View the input QoS policy details. Z9000 Syntax Parameters show qos qos-policy-input [qos-policy-name] qos-policyname Enter the QoS policy name. Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1263
show qos qos-policy-output View the output QoS policy details. Z9000 Syntax Parameters show qos qos-policy-output [qos-policy-name] qos-policyname Enter the QoS policy name. Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.
PAGE 1264
Parameters wred-profile interface interface Enter the keywords wred-profile and optionally one of the following keywords and slot/port or number information: • For a 40–Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a ten-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 1265
• Command History EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810.
PAGE 1266
Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.
PAGE 1267
Field Description Status (Allowed ports) Indicates if the input policy map configuration on an interface belonging to a stack-unit/port-pipe is successful — Allowed (n) — or not successful — Exception. The allowed number (n) indicates the number of ports in that port-pipe on which the Policy Map can be applied successfully. NOTE: In a Layer 2 Policy Map, IPv4/IPv6 rules are not allowed; therefore, the output contains only L2ACL CAM partition entries.
PAGE 1268
Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.
PAGE 1269
Command Modes CONFIGURATION (config-wred) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.8.0 Introduced on the S4810. pre-Version 6.1.1.
PAGE 1270
The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Added fallback to the E-Series. Version 8.2.1.0 Added dot1p to the C-Series and S-Series. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.
PAGE 1271
DSCP/CP hex Range (XXX) DSCP Definition Traditional IP Precedenc e S6000 Internal Queue ID S-Series Internal Queue ID DSCP/CP Decimal 000XXX BE (Best Effort) Best Effort 0 0 0–15 wred Designate the WRED profile to yellow or green traffic. Z-Series Syntax wred {yellow | green} profile-name To remove the WRED drop precedence, use the no wred {yellow | green} [profilename] command. Parameters yellow | green Enter the keyword yellow for yellow traffic.
PAGE 1272
Version 8.2.1.0 Profile name character limit increased from 16 to 32. pre-Version 6.1.1.1 Introduced on the .E-Series Usage Information To assign drop precedence to green or yellow traffic, use this command. If there is no honoring enabled on the input, all the traffic defaults to green drop precedence. Related Commands wred-profile — creates a WRED profile and name that profile. trust — defines the dynamic classification to trust DSCP.
PAGE 1273
• If neither endpoint is ECN-capable, the packet may be dropped based on the WRED drop probability. This behavior is the identical treatment that a packet receives when WRED is enabled without ECN configured on the router. When you enable wred ecn, and the number of packets in the queue is above the maximum threshold, packets are dropped based on the drop probability. This behavior is the identical treatment a packet receives when WRED is enabled without ECN configured on the router.
PAGE 1274
pre-Version 6.1.1.1 Introduced on the E-Series Usage Information Use the default pre-defined profiles or configure your own profile. You cannot delete the pre-defined profiles or their default values. This command enables WRED configuration mode —(conf-wred). Related Commands threshold — specifies the minimum and maximum threshold values of the WRED profile.
PAGE 1275
Command Modes Command History Usage Information CONFIGURATION mode Version 9.3.0.0 Introduced on the S6000 and Z9000 platforms You can configure only service pools 0 and 1 because the Dell Networking OS uses only these two service pools. The pool, service0, is used for lossy queues and the pool, service1, is used for lossless (PFC) queues in all the platforms.
PAGE 1276
backplane Specify that the ECN marking configured for each queue applies to backplane ports Default By default, ECN marking is disabled on all queues. Command Modes CONFIGURATION mode Command History Usage Information Example Version 9.3.0.0 Introduced on the S6000 and Z9000 platforms You can add or remove ECN marking configuration on a list of queues on all backplane ports. All of the configured attributes apply to all the backplane ports and are for each queue.
PAGE 1277
string] || [queue3 number/string] || [queue4 number/string] || [queue5 number/string] || [queue6 number/string] || [queue7 number/string]}{backplane} Parameters service-class Define the mapping between the service class and policybased QoS or routing wred Specify WRED curve parameters for a queue green Specify green (low) drop precedence to a queue weight Specify a weight factor to a queue yellow Specify yellow (medium) drop precedence to a queue queue 0 to queue 7 Specify the queue number to wh
PAGE 1278
Dell(conf) #service-class wred weight queue0 11 queue6 4 queue7 9 backplane service-class wred ecn Create a service class and assign ECN marking for different queues on backplane ports to the service class. This functionality can be configured on the Z9000 platforms.
PAGE 1279
• Example Quality of Service (QoS) If the network is experiencing congestion, the packet is transmitted. No further marking is required. When you enable wred-ecn, and the number of packets in the queue is above the maximum threshold, packets are dropped based on the drop probability. This behavior is the identical treatment a packet receives when WRED is enabled without ECN configured on the router.
PAGE 1280
PAGE 1281
Routing Information Protocol (RIP) 41 Routing information protocol (RIP) is a distance vector routing protocol. The Dell Networking operating software supports both RIP version 1 (RIPv1) and RIP version 2 (RIPv2) on the Z9000 platform. The Dell Networking OS implementation of RIP is based on IETF RFCs 2453 and RFC 1058. For more information about configuring RIP, refer to the Dell Networking OS Configuration Guide.
PAGE 1282
clear ip rip Update all the RIP routes in the Dell Networking OS routing table. Z9000 Syntax clear ip rip Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.
PAGE 1283
• For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a VLAN, enter the keyword vlan then a number from 1 to 4094. database (OPTIONAL) Enter the keyword database to display messages when there is a change to the RIP database.
PAGE 1284
To return to the default values, use the no default-information originate command. Parameters always (OPTIONAL) Enter the keyword always to enable the switch software to always advertise the default route. metric metricvalue (OPTIONAL) Enter the keyword metric then a number as the metric value. The range is from 1 to 16. The default is 1. route-map map-name (OPTIONAL) Enter the keywords route-map then the name of a configured route-map. Defaults Disabled. Metric: 1.
PAGE 1285
Parameters number Specify a number. The range is from 1 to 16. The default is 1. Defaults 1 Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000.
PAGE 1286
Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.
PAGE 1287
Defaults weight = 120 Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.
PAGE 1288
• For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a VLAN, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured. Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.
PAGE 1289
interface (OPTIONAL) Identifies the interface type slot/port as one of the following: • For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet followed by the slot/ port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 1290
ip poison-reverse Set the prefix of the RIP routing updates to the RIP infinity value. Z9000 Syntax ip poison-reverse To disable poison reverse, use the no ip poison-reverse command. Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1291
2 (OPTIONAL) Enter the number 2 for RIP version 2. Defaults RIPv1 and RIPv2 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.
PAGE 1292
Defaults RIPv1 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.
PAGE 1293
Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.6.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. ip poison-reverse — sets the prefix for RIP routing updates. maximum-paths Set RIP to forward packets over multiple paths.
PAGE 1294
Usage Information Version 7.6.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. RIP supports a maximum of 16 ECMP paths. neighbor Define a neighbor router with which to exchange RIP information. Z9000 Syntax neighbor ip-address To delete a neighbor setting, use the no neighbor ip-address command. Parameters ip-address Enter the IP address, in dotted decimal format, of a router with which to exchange information. Defaults Not configured.
PAGE 1295
To ensure that only specific interfaces are receiving and sending data, use the passive-interface command with the neighbor command. Related Commands passive-interface — sets the interface to only listen to RIP broadcasts. network Enable RIP for a specified network. To enable RIP on all networks connected to the switch, use this command. Z9000 Syntax network ip-address To disable RIP for a network, use the no network ip-address command.
PAGE 1296
offset-list Specify a number to add to the incoming or outgoing route metrics learned using RIP. Z9000 Syntax offset-list prefix-list-name {in | out} offset [interface] To delete an offset list, use the no offset-list prefix-list-name {in | out} offset [interface] command. Parameters prefix-listname Enter the name of an established Prefix list to determine which incoming routes are modified.
PAGE 1297
Version 7.8.1.0 Introduced on the S-Series. Version 7.6.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. Usage Information When the offset metric is applied to an interface, that value takes precedence over an offset value that is not extended to an interface. Related Commands ip prefix-list — enters PREFIX-LIST mode and configure a prefix list. output-delay Set the interpacket delay of successive packets to the same neighbor.
PAGE 1298
Usage Information This command is intended for low-speed interfaces. passive-interface Suppress routing updates on a specified interface. Z9000 Syntax passive-interface interface To delete a passive interface, use the no passive-interface interface command. Parameters interface Enter the following information: • For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128.
PAGE 1299
Version 7.6.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. Usage Information Although the passive interface does not send or receive routing updates, the network on that interface still includes in RIP updates sent using other interfaces. Related Commands neighbor — enables RIP for a specified network. network — defines a neighbor. redistribute Redistribute information from other routing instances.
PAGE 1300
pre-Version 6.2.1.1 Introduced on the E-Series. Usage Information To redistribute the default route (0.0.0.0/0), configure the default-information originate command. Related Commands default-information originate — generates a default route for RIP traffic. redistribute isis Redistribute routing information from an IS-IS instance.
PAGE 1301
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. pre-Version 6.2.1.1 Introduced on the E-Series. redistribute ospf Redistribute routing information from an OSPF process.
PAGE 1302
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.6.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. router rip To configure and enable RIP, enter ROUTER RIP mode. Z9000 Syntax router rip To disable RIP, use the no router rip command. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1303
Related Commands network — enables RIP. exit — returns to CONFIGURATION mode. show config Display the changes you made to the RIP configuration. The default values are not shown. Z9000 Syntax show config Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.
PAGE 1304
show ip rip database Display the routes that RIP learns. If the switch learned no RIP routes, no output is generated. Z9000 Syntax Parameters show ip rip database [ip-address mask] ip-address (OPTIONAL) Specify an IP address in dotted decimal format to view RIP information on that network only. If you enter an IP address, also enter a mask for that IP address. mask (OPTIONAL) Specify a mask, in /network format, for the IP address.
PAGE 1305
Example Dell#show ip rip database Total number of routes in RIP database: 1624 204.250.54.0/24 [50/1] via 192.14.1.3, 00:00:12, GigabitEthernet 9/15 204.250.54.0/24 auto-summary 203.250.49.0/24 [50/1] via 192.13.1.3, 00:00:12, GigabitEthernet 9/14 203.250.49.0/24 auto-summary 210.250.40.0/24 [50/2] via 1.1.18.2, 00:00:14, Vlan 18 [50/2] via 1.1.130.2, 00:00:12, Port-channel 30 210.250.40.0/24 auto-summary 207.250.53.0/24 [50/2] via 1.1.120.2, 00:00:55, Port-channel 20 [50/2] via 1.1.130.
PAGE 1306
Example show running-config rip ! router rip distribute-list Test1 in distribute-list Test21 out network 10.0.0.0 passive-interface GigabitEthernet 2/0 neighbor 20.20.20.20 redistribute ospf 999 version 2 timers basic Manipulate the RIP timers for routing updates, invalid, holddown times, and flush time. Z9000 Syntax timers basic update invalid holddown flush To return to the default settings, use the no timers basic command.
PAGE 1307
Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.
PAGE 1308
Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.6.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. ip rip receive version — sets the RIP version the interface receives. ip rip send version — sets the RIP version the interface sends.
PAGE 1309
Remote Monitoring (RMON) 42 The Dell Networking operating software remote monitoring (RMON) is implemented on the Z9000 platform. Dell Networking OS RMON is based on IEEE standards, providing both 32-bit and 64-bit monitoring and long-term statistics collection.
PAGE 1310
variable Enter the MIB object to monitor. The variable must be in the SNMP OID format; for example, 1.3.6.1.2.1.1.3. The object type must be a 32-bit integer. interval Time, in seconds, the alarm monitors the MIB variables; this is the alarmSampleType in the RMON alarm table. The range is from 5 to 3600 seconds. delta Enter the keyword delta to test the change between MIB variables. This is the alarmSampleType in the RMON alarm table.
PAGE 1311
Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.1.1.0 Introduced on the E-Series. rmon collection history Enable the RMON MIB history group of statistics collection on an interface. Z9000 Syntax rmon collection history {controlEntry integer} [owner name] [buckets number] [interval seconds] To remove a specified RMON history group of statistics collection, use the no rmon collection history {controlEntry integer} command.
PAGE 1312
Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.1.1.0 Introduced on the E-Series. rmon collection statistics Enable RMON MIB statistics collection on an interface. Z9000 Syntax rmon collection statistics {controlEntry integer} [owner name] To remove RMON MIB statistics collection on an interface, use the no rmon collection statistics {controlEntry integer} command.
PAGE 1313
Version 6.1.1.0 Introduced on the E-Series. rmon event Add an event in the RMON event table. Z9000 Syntax rmon event number [log] [trap community] [description string] [owner name] To disable RMON on an interface, use the no rmon event number [log] [trap community] [description string] command. Parameters number Assign an event number in integer format from 1 to 65535. The number value must be unique in the RMON event table. log (OPTIONAL) Enter the keyword log to generate an RMON log entry.
PAGE 1314
Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.1.1.0 Introduced on the E-Series. rmon hc-alarm Set an alarm on any MIB object. Z9000 Syntax rmon hc-alarm number variable interval {delta | absolute} rising-threshold value event-number falling-threshold value event-number [owner string] To disable the alarm, use the no rmon hc-alarm number command. Parameters 1314 number Enter the alarm integer number from 1 to 65535.
PAGE 1315
If there is no corresponding falling-threshold event, the value is zero. owner string (OPTIONAL) Enter the keyword owner then the owner name to specify an owner for the alarm. This is the alarmOwner object in the alarmTable of the RMON MIB. Defaults owner Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1316
Example Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.1.1.0 Introduced on the E-Series. Dell# show rmon RMON status total memory used 218840 bytes.
PAGE 1317
Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.1.1.0 Introduced on the E-Series. Example (Index) Dell#show rmon alarm 1 RMON alarm entry 1 sample Interval: 5 object: 1.3.6.1.2.1.1.3 sample type: absolute value. value: 255161 alarm type: rising or falling alarm.
PAGE 1318
show rmon events Display the contents of the RMON event table. Z9000 Syntax Parameters show rmon events [index] [brief] index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON event table in an easy-to-read format. Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1319
7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Dell# 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 show rmon hc-alarm Display the contents of RMON High-Capacity alarm table. Z9000 Syntax Parameters show rmon hc-alarm [index] [brief] index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON High-Capacity alarm table in an easy-to-read format. Defaults none Command Modes EXEC Command History This guide is platform-specific.
PAGE 1320
Version 6.1.1.0 Introduced on the E-Series. Example (Index) Dell#show rmon hc-alarm 1 RMON high-capacity alarm entry 1 object: 1.3.6.1.2.1.1.3 sample interval: 5 sample type: absolute value. value: 185638 alarm type: rising or falling alarm. alarm rising threshold value: positive. rising threshold: 1001, RMON event index: 1 alarm falling threshold value: positive. falling threshold: 999, RMON event index: 6 alarm sampling failed 0 times. alarm owner: 1 alarm storage type: non-volatile.
PAGE 1321
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.1.1.0 Introduced on the E-Series. Example (Index) Dell#show rmon history 6001 RMON history control entry 6001 interface: ifIndex.
PAGE 1322
Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series.
PAGE 1323
Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example (Index) Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.
PAGE 1324
HC 1024-1518 bytes packets overflow: 0 HC 1024-1518 bytes packets: 0 Dell# Example (Brief) 1324 Dell#show rmon statistics br index ifIndex interface ---------------------------------------6001 100974631 TenGigabitEthernet 2/0 6002 100974631 TenGigabitEthernet 2/0 6003 101236775 TenGigabitEthernet 2/1 6004 101236775 TenGigabitEthernet 2/1 9001 134529054 TenGigabitEthernet 3/0 9002 134529054 TenGigabitEthernet 3/0 9003 134791198 TenGigabitEthernet 3/1 9004 134791198 TenGigabitEthernet 3/1 Dell# Remote Moni
PAGE 1325
Rapid Spanning Tree Protocol (RSTP) 43 The Dell Networking operating software implementation of rapid spanning tree protocol (RSTP) is based on the IEEE 802.1w standard spanning-tree protocol. The RSTP algorithm configures connectivity throughout a bridged local area network (LAN) that is comprised of LANs interconnected by bridges. Dell Networking OS supports RSTP on the Z9000 platform. bridge-priority Set the bridge priority for RSTP.
PAGE 1326
Related Commands protocol spanning-tree rstp — enters rapid spanning tree mode. debug spanning-tree rstp Enable debugging of RSTP and view information on the protocol. Z9000 Syntax debug spanning-tree rstp [all | bpdu interface {in | out} | events] To disable debugging, use the no debug spanning-tree rstp command. Parameters all (OPTIONAL) Enter the keyword all to debug all spanning tree operations. bpdu interface {in | out} (OPTIONAL) Enter the keyword bpdu to debug the bridge protocol data units.
PAGE 1327
Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.2.1.1 Introduced on the E-Series.
PAGE 1328
Related Commands Version 8.3.7.0 Introduced on the S4810. pre-7.7.1.0 Introduced. protocol spanning-tree rstp — enters SPANNING TREE mode on the switch. disable Disable RSTP globally on the system. Z9000 Syntax disable To enable Rapid Spanning Tree Protocol, use the no disable command. Defaults RSTP is disabled. Command Modes CONFIGURATION RSTP (conf-rstp) Command History This guide is platform-specific.
PAGE 1329
forward-delay Configure the amount of time the interface waits in the Listening State and the Learning State before transitioning to the Forwarding State. Z9000 Syntax forward-delay seconds To return to the default setting, use the no forward-delay command. Parameters seconds Enter the number of seconds that FTOS waits before transitioning RSTP to the forwarding state. The range is from 4 to 30. The default is 15 seconds.
PAGE 1330
hello-time Set the time interval between the generation of the RSTP bridge protocol data units (BPDUs). Z9000 Syntax hello-time [milli-second] seconds To return to the default value, use the no hello-time command. Parameters seconds Enter a number as the time interval between transmission of BPDUs. The range is from 1 to 10 seconds. The default is 2 seconds. milli-second Enter the keywords milli-second to configure a hello time on the order of milliseconds.
PAGE 1331
Related Commands forward-delay — changes the wait time before RSTP transitions to the Forwarding state. max-age — changes the wait time before RSTP refreshes the protocol configuration information. max-age To maintain configuration information before refreshing that information, set the time interval for the RSTP bridge. Z9000 Syntax max-age seconds To return to the default values, use the no max-age command.
PAGE 1332
hello-time — changes the time interval between BPDUs. protocol spanning-tree rstp To configure RSTP, enter RSTP mode. Z9000 Syntax protocol spanning-tree rstp To exit RSTP mode, use the exit command. Defaults Not configured Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1333
show config View the current configuration for the mode. Only non-default values are displayed. Z9000 Syntax show config Command Modes CONFIGURATION RSTP (conf-rstp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 1334
Command Modes Command History Usage Information Example (Brief) • EXEC • EXEC Privilege Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.4.2.1 Added support for the optional guard keyword on the CSeries, S-Series, and E-Series TeraScale. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.4.1.
PAGE 1335
Gi 4/9 Altr 128.427 128 20000 BLK 20000 P2P Dell# Example (EDS, LBK) No NOTE: “LBK_INC” (bold) means Loopback BPDU Inconsistency. Dell#show spanning-tree rstp br Executing IEEE compatible Spanning Tree Protocol Root ID Priority 32768, Address 0001.e801.6aa8 Root Bridge hello time 2, max age 20, forward delay 15 Bridge ID Priority 32768, Address 0001.e801.
PAGE 1336
spanning-tree rstp Configure an RSTP interface with one of these settings: port cost, edge port with optional bridge port data unit (BPDU) guard, port priority, loop guard, or root guard. Z9000 Syntax Parameters spanning-tree rstp {cost port-cost | edge-port [bpduguard [shutdown-on-violation]] | priority priority | {loopguard | rootguard}} cost port-cost Enter the keyword cost then the port cost value. The range is from 1 to 200000.
PAGE 1337
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.4.2.
PAGE 1338
• Example If no BPDU is received from a remote device, loop guard places the port in a Loop-Inconsistent Blocking state and no traffic is forwarded on the port. Dell(conf)#interface gigabitethernet 4/0 Dell(conf-if-gi-4/0)#spanning-tree rstp edge-port Dell(conf-if-gi-4/0)#show config ! interface GigabitEthernet 4/0 no ip address switchport spanning-tree rstp edge-port no shutdown Dell# tc-flush-standard Enable the MAC address flushing after receiving every topology change notification.
PAGE 1339
knob command to enable flushing MAC addresses after receiving every topology change notification.
PAGE 1340
PAGE 1341
Software-Defined Networking (SDN) 44 Dell Networking operating software supports Software-Defined Networking (SDN). For more information, refer to the SDN Deployment Guide.
PAGE 1342
PAGE 1343
45 Security Most of the commands in this chapter are available on the Z9000 platform. This chapter contains various types of security commands offered in the Dell Networking operating software. The commands are listed in the following sections: • AAA Accounting Commands • Authorization and Privilege Commands • Authentication and Password Commands • RADIUS Commands • TACACS+ Commands • Port Authentication (802.
PAGE 1344
Parameters system Enter the keyword system to send accounting information of any other AAA configuration. exec Enter the keyword exec to send accounting information when a user has logged in to EXEC mode. commands level Enter the keyword command then a privilege level for accounting of commands executed at that privilege level. name | default Enter one of the following: • For name, enter a user-defined name of a list of accounting methods. • For default, the default accounting methods used.
PAGE 1345
Usage Information In the example above, TACACS+ accounting is used to track all usage of EXEC command and commands on privilege level 15. Privilege level 15 is the default. If you want to track usage at privilege level 1 for example, use the aaa accounting command 1 command. Example Dell(conf)# aaa accounting exec default start-stop tacacs+ Dell(conf)# aaa accounting command 15 default start-stop tacacs + Dell(config)# Related Commands enable password — changes the password for the enable command.
PAGE 1346
Usage Information Dell Networking OS issues accounting records for all users on the system, including users whose username string, due to protocol translation, is NULL. For example, a user who comes on line with the aaa authentication login method-list none command is applied. To prevent the accounting records from being generated for sessions that do not have user names associated to them, use the aaa accounting suppress command.
PAGE 1347
tacacs-server group Creates a group of TACACS servers to be used for Authentication, Authorization, and Accounting.. Z9000 Syntax aaa tacacsgroup group-name To delete a group of TACACS servers, use the no tacacs-server group group-name command. Parameters group-name Enter the name of the TACACS server group. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1348
commands level Enter the keywords commands level to apply an EXEC and CONFIGURATION level accounting method list. method-list Enter a method list that you defined using the aaa accounting exec or aaa accounting commands. Defaults none Command Modes LINE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1349
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.3.1.0 Introduced on the E-Series. Usage Information This command steps through all active sessions and then displays the accounting records for the active account functions.
PAGE 1350
Command Modes LINE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series.
PAGE 1351
Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.
PAGE 1352
Version 7.5.1.0 Usage Information Introduced on the E-Series. By default, the aaa authorization commands command configures the system to check both EXEC level and CONFIGURATION level commands. Use the command no aaa authorization config-commands to enable only EXEClevel command checking. aaa authorization exec Set parameters that restrict (or permit) a user’s access to EXEC-level commands.
PAGE 1353
privilege level (CONFIGURATION mode) Change the access or privilege level of one or more commands. Z9000 Syntax privilege mode {level level command | reset command} To delete access to a level and command, use the no privilege mode level level command command.
PAGE 1354
Usage Information Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. To define a password for the level to which you are assigning privilege or access, use the enable password command. privilege level (LINE mode) Change the access level for users on the terminal lines.
PAGE 1355
pre-Version 6.1.1.0 Introduced on the E-Series. Authentication and Password Commands To manage access to the system, use the following the commands. aaa authentication enable Configure AAA Authentication method lists for user access to EXEC privilege mode (the “Enable” access). Z9000 Syntax aaa authentication enable {default | method-list-name} method [... method2] To return to the default setting, use the no aaa authentication enable {default | method-list-name} method [... method2] command.
PAGE 1356
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.
PAGE 1357
To return to the default setting, use the no aaa authentication login {method-list-name | default} command. Parameters method-listname Enter a text string (up to 16 characters long) as the name of a user-configured method list that can be applied to different lines. default Enter the keyword default to specify that the method list specified is the default method for all terminal lines. method Enter one of the following methods: ...
PAGE 1358
Usage Information By default, the locally configured username password is used. If you configure aaa authentication login default, Dell Networking OS uses the methods this command defines for login instead. Methods configured with the aaa authentication login command are evaluated in the order they are configured. If users encounter an error with the first method listed, Dell Networking OS applies the next method configured. If users fail the first method listed, no other methods are applied.
PAGE 1359
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.
PAGE 1360
password Enter a text string, up to 32 characters long, as the clear text password. Defaults No password is configured. level = 15. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 1361
enable restricted Allows Dell Networking technical support to access restricted commands. Z9000 Syntax enable restricted [encryption-type] password To disallow access to restricted commands, use the no enable restricted command. Parameters encryptiontype (OPTIONAL) Enter the number 7 as the encryption type. Enter 7 followed a text string as the hidden password. The text string must be a password that was already encrypted by a Dell Networking router.
PAGE 1362
enable secret Change the password for the enable command. Z9000 Syntax enable secret [level level] [encryption-type] password To delete a password, use the no enable secret [encryption-type] password [level level] command. Parameters level level (OPTIONAL) Enter the keyword level then a number as the level of access. The range is from 1 to 15. encryptiontype (OPTIONAL) Enter the number 5 or 0 as the encryption type. Enter a 5 then a text string as the hidden password.
PAGE 1363
Usage Information To control access to command modes, use this command to define a password for a level and use the privilege level (CONFIGURATION mode) command. Passwords must meet the following criteria: • Start with a letter, not a number. • Passwords can have a regular expression as the password. To create a password with a regular expression in it, use CNTL + v prior to entering regular expression. For example, to create the password abcd]e, you type “abcd CNTL v ]e”.
PAGE 1364
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series. Usage Information If you configure the aaa authentication login default command, the login authentication default command automatically is applied to all terminal lines.
PAGE 1365
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. Usage Information Dell Networking OS prompts users for these passwords when the method for authentication or authorization used is "line". Related Commands enable password — sets the password for the enable command.
PAGE 1366
characterrestriction (OPTIONAL) Enter the keywords character-restriction to indicate a character restriction for the password. upper number (OPTIONAL) Enter the keyword upper then the upper number. The range is from 0 to 31. lower number (OPTIONAL) Enter the keyword lower then the lower number. The range is from 0 to 31. numeric number (OPTIONAL) Enter the keyword numeric then the numeric number. The range is from 0 to 31.
PAGE 1367
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series.
PAGE 1368
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. Example Dell#show privilege Current privilege level is 15 Dell# Related Commands privilege level (CONFIGURATION mode) — assigns access control to different command modes.
PAGE 1369
pre-Version 6.1.1.0 Usage Information Example Related Commands Introduced on the E-Series. The following describes the show user command shown in the following example. Field Description (untitled) Indicates with an asterisk (*) which terminal line you are using. Line Displays the terminal lines currently in use. User Displays the user name of all users logged in. Host(s) Displays the terminal line status. Location Displays the IP address of the user.
PAGE 1370
Command Modes LINE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series.
PAGE 1371
secret Enter the keyword secret then the encryption-type or the password. encryptiontype Enter an encryption type for the password that you enter. • 0 directs Dell Networking OS to store the password as clear text. It is the default encryption type when using the password option. • 7 to indicate that a password encrypted using a DES hashing algorithm follows. This encryption type is available with the password option only.
PAGE 1372
Related Commands password — specifies a password for users on terminal lines. show running-config — views the current configuration. RADIUS Commands The following RADIUS commands are supported by Dell Networking OS. debug radius View RADIUS transactions to assist with troubleshooting. Z9000 Syntax debug radius To disable debugging of RADIUS, use the no debug radius command. Defaults Disabled. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 1373
To delete a source interface, use the no ip radius source-interface command. Parameters interface Enter the following keywords and slot/port or number information: • For a 100/1000 Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For Loopback interfaces, enter the keyword loopback then a number from zero (0) to 16838.
PAGE 1374
radius-server deadtime Configure a time interval during which non-responsive RADIUS servers to authentication requests are skipped. Z9000 Syntax radius-server deadtime seconds To disable this function or return to the default value, use the no radius-server deadtime command. Parameters seconds Enter a number of seconds during which non-responsive RADIUS servers are skipped. The range is from 0 to 2147483647 seconds. The default is 0 seconds.
PAGE 1375
Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. (0.0) Introduced on the S-Series and Z-Series. Example FTOS(conf)#radius-server group group1 FTOS(conf-radius-group)#radius-server host 1.1.1.
PAGE 1376
retransmit retries (OPTIONAL) Enter the keyword retransmit then a number as the number of attempts. This parameter overwrites the radius-server retransmit command. The range is from zero (0) to 100. The default is 3 attempts. timeout seconds (OPTIONAL) Enter the keyword timeout then the seconds the time interval the switch waits for a reply from the RADIUS server. This parameter overwrites the radius-server timeout command. The range is from 0 to 1000. The default is 5 seconds.
PAGE 1377
pre-Version 6.2.1.0 Usage Information Introduced on the E-Series. To configure any number of RADIUS server hosts for each server host that is configured, use this command. Dell Networking OS searches for the RADIUS hosts in the order they are configured in the software. The global default values for the timeout, retransmit, and key optional parameters are applied, unless those values are specified in the radius-server host or other commands.
PAGE 1378
To delete a password, use the no radius-server key command. Parameters encryptiontype key (OPTIONAL) Enter either zero (0) or 7 as the encryption type for the key entered. The options are: • 0 is the default and means the key is not encrypted and stored as clear text. • 7 means that the key is encrypted and hidden. Enter a string that is the key to be exchanged between the switch and RADIUS servers. It can be up to 42 characters long. Defaults Not configured.
PAGE 1379
radius-server retransmit Configure the number of times the switch attempts to connect with the configured RADIUS host server before declaring the RADIUS host server unreachable. Z9000 Syntax radius-server retransmit retries To configure zero retransmit attempts, use the no radius-server retransmit command. To return to the default setting, use the radius-server retransmit 3 command. Parameters retries Enter a number of attempts that FTOS tries to locate a RADIUS server.
PAGE 1380
radius-server timeout To reply to a request, configure the amount of time the RADIUS client (the switch) waits for a RADIUS host server . Z9000 Syntax radius-server timeout seconds To return to the default value, use the no radius-server timeout command. Parameters seconds Enter the number of seconds between an unsuccessful attempt and the Dell Networking OS times out. The range is from zero (0) to 1000 seconds. The default is 5 seconds.
PAGE 1381
To delete the association between a RADIUS server group and a VRF and source interface, use the no radius-server vrf vrf-name [source-interface interface] command. Parameters vrf vrf-name Enter the keyword vrf and then the name of the VRF to associate a RADIUS server group with that VRF. interface Enter the following keywords and slot/port or number information: • For a 100/1000 Ethernet interface, enter the keyword GigabitEthernet then the slot/port information.
PAGE 1382
group. When the VRF is removed, then the corresponding RADIUS group is also removed automatically. Example Dell(conf)#radius-server group group1 Dell(conf-radius-group)#radius-server vrf vrf1 sourceinterface tengigabitethernet 0/36 Dell(conf)#radius-server group group2 Dell(conf-radius-group)#radius-server vrf default TACACS+ Commands Dell Networking OS supports TACACS+ as an alternate method for login authentication. debug tacacs+ To assist with troubleshooting, view TACACS+ transactions.
PAGE 1383
tacacs-server group Creates a group of TACACS servers. Z9000 Syntax tacacs-server group group-name To delete a group of TACACS servers, use the no tacacs-server group group-name command. Parameters group-name Enter the name of the TACACS server group. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1384
tacacs-server host Specify a TACACS+ host. Z9000 Syntax Parameters tacacs-server host {hostname | ipv4-address | ipv6-address} [port number] [timeout seconds] [key key] hostname Enter the name of the TACACS+ server host. ipv4-address | ipv6-address Enter the IPv4 address (A.B.C.D) or IPv6 address (X:X:X:X::X) of the TACACS+ server host. port number (OPTIONAL) Enter the keyword port then a number as the port to be used by the TACACS+ server. The range is from zero (0) to 65535. The default is 49.
PAGE 1385
pre-Version 6.2.1.1 Usage Information Introduced on the E-Series. To list multiple TACACS+ servers to be used by the aaa authentication login command, configure this command multiple times. If you are not configuring the switch as a TACACS+ server, you do not need to configure the port, timeout and key optional parameters. If you do not configure a key, the key assigned in the tacacs-server key command is used. You can use duplicate host names or IP addresses among TACACS groups.
PAGE 1386
• For a Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For Loopback interfaces, enter the keyword loopback then a number from zero (0) to 16838. • For the Null interface, enter the keywords null 0. • For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a ten-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 1387
tacacs-server key Configure a key for communication between a TACACS+ server and a client. Z9000 Syntax tacacs-server key [encryption-type] key To delete a key, use the no tacacs-server key key command. Parameters encryptiontype key (OPTIONAL) Enter either zero (0) or 7 as the encryption type for the key entered. The options are: • 0 is the default and means the key is not encrypted and stored as clear text. • 7 means that the key is encrypted and hidden.
PAGE 1388
ip tacacs source-interface Specify an interface’s IP address as the source IP address for TACACS+ connections. Z9000 Syntax ip tacacs source-interface interface To delete a source interface, use the no ip tacacs source-interface command. Parameters interface Enter the following keywords and slot/port or number information: • For a 100/1000 Ethernet interface, enter the keyword GigabitEthernet then the slot/port information.
PAGE 1389
Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. Port Authentication (802.1X) Commands An authentication server must authenticate a client connected to an 802.1X switch port. Until the authentication, only Extensible Authentication Protocol over LAN (EAPOL) traffic is allowed through the port to which a client is connected. After authentication is successful, normal traffic passes through the port.
PAGE 1390
Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the C-Series and S-Series.
PAGE 1391
Related Commands dot1x authentication (Configuration) — enables dot1x globally. dot1x auth-fail-vlan Configure an authentication failure VLAN for users and devices that fail 802.1X authentication. Z9000 Syntax dot1x auth-fail-vlan vlan-id [max-attempts number] To delete the authentication failure VLAN, use the no dot1x auth-fail-vlan vlan-id [max-attempts number] command. Parameters vlan-id Enter the VLAN Identifier. The range is from 1 to 4094.
PAGE 1392
show dot1x interface — displays the 802.1X information on an interface. dot1x auth-server Configure the authentication server to RADIUS. Z9000 Syntax dot1x auth-server radius Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.
PAGE 1393
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the C-Series, S-Series, and E-Series. 802.1X authentication is enabled when an interface is connected to the switch. If the host fails to respond within a designated amount of time, the authenticator places the port in the guest VLAN.
PAGE 1394
The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.4 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.4.1.0 Introduced on the C-Series and S-Series. To disable MAC authentication bypass on a port, enter the no dot1x mac-authbypass command.
PAGE 1395
Related Commands interface range — configures a range of interfaces. dot1x port-control Enable port control on an interface. Z9000 Syntax Parameters dot1x port-control {force-authorized | auto | forceunauthorized} forceauthorized Enter the keywords force-authorized to forcibly authorize a port. auto Enter the keyword auto to authorize a port based on the 802.1X operation result. forceunauthorized Enter the keywords force-unauthorized to forcibly deauthorize a port.
PAGE 1396
To disable quiet time, use the no dot1x quiet-time command. Parameters seconds Enter the number of seconds. The range is from 1 to 65535. The default is 30. Defaults 30 seconds Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
PAGE 1397
Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the C-Series and S-Series. Version 7.4.1.0 Introduced on the E-Series. interface range — configures a range of interfaces. dot1x reauth-max Configure the maximum number of times a port can re-authenticate before the port becomes unauthorized.
PAGE 1398
dot1x server-timeout Configure the amount of time after which exchanges with the server time-out. Z9000 Syntax dot1x server-timeout seconds To return to the default, use the no dot1x server-timeout command. Parameters seconds Enter a time-out value in seconds. The range is from 1 to 300, where 300 is implementation dependant. The default is 30. Defaults 30 seconds Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1399
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the C-Series and S-Series.
PAGE 1400
Version 7.4.1.0 Introduced on the E-Series. show dot1x interface Display the 802.1X information on an interface. Z9000 Syntax Parameters show dot1x interface interface interface Enter one of the following keywords and slot/port or number information: • For a Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a Fast Ethernet interface, enter the keyword FastEthernet then the slot/ port information.
PAGE 1401
Guest VLAN: Guest VLAN id: Auth-Fail VLAN: Auth-Fail VLAN id: Auth-Fail Max-Attempts: Tx Period: Quiet Period: ReAuth Max: Supplicant Timeout: Server Timeout: Re-Auth Interval: Max-EAP-Req: Auth Type: Auth PAE State: Backend State: Dell# Enable 10 Enable 11 3 30 seconds 60 seconds 2 30 seconds 30 seconds 3600 seconds 2 SINGLE_HOST Initialize Initialize SSH Server and SCP Commands Dell Networking OS supports secure shell (SSH) protocol versions 1.5 and 2.0.
PAGE 1402
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.12.0 Added support for FIPS mode on the S4810. Version 8.3.7.
PAGE 1403
To disable debugging, use the no debug ip ssh {client | server} command. Parameters client Enter the keyword client to enable collecting debug information on the client. server Enter the keyword server to enable collecting debug information on the server. Defaults Disabled on both client and server. Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1404
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series.
PAGE 1405
Usage Information Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. This command specifies the maximum number of attempts to authenticate a user on an SSH connection with the remote host for password authentication. SSH disconnects when the number of password failures exceeds authentication-retries.
PAGE 1406
ip ssh hostbased-authentication Enable hostbased-authentication for the SSHv2 server. Z9000 Syntax ip ssh hostbased-authentication enable To disable hostbased-authentication for SSHv2 server, use the no ip ssh hostbased-authentication enable command. Parameters enable Enter the keyword enable to enable hostbasedauthentication for SSHv2 server. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1407
ip ssh rhostsfile — trusted hosts and users for rhost authentication. ip ssh key-size Configure the size of the server-generated RSA SSHv1 key. Z9000 Syntax Parameters ip ssh key-size 512-869 512-869 Enter the key-size number for the server-generated RSA SSHv1 key. The range is from 512 to 869. The default is 768. Defaults Key size 768 Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1408
Parameters enable Enter the keyword enable to enable passwordauthentication for the SSH server. Defaults Enabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T.
PAGE 1409
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. This command specifies the file used for the host-based authentication. The creates/ file overwrites the flash://ADMIN_DIR/ssh/knownhosts file and deletes the user-specified file.
PAGE 1410
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series.
PAGE 1411
Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.
PAGE 1412
The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series.
PAGE 1413
NOTE: If you enable FIPS mode, you can only select version 2. Defaults Default listening port is 22. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.
PAGE 1414
To disable the SSH server configuration, use the no ip ssh server vrf {management | vrf-name} command. Parameters vrf management Enter the key word vrf followed by the keyword management to configure an SSH server on a management VRF. vrf vrf-name Enter the key word vrf followed by the VRF name to configure an SSH server on that VRF. Defaults None Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1415
Parameters interface Enter the following keywords and slot/port or number information: • For a 100/1000 Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For Loopback interfaces, enter the keyword loopback then a number from zero (0) to 16838. • For the Null interface, enter the keywords null 0.
PAGE 1416
To delete a VRF for an outgoing SSH connection, use the no ip ssh vrf vrfname command. Parameters vrf vrf-name Enter the keyword vrf and then the name of the VRF to configure that VRF for an outgoing SSH session. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1417
Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series.
PAGE 1418
Command Modes Command History • • EXEC EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.
PAGE 1419
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. Usage Information This command displays the contents of the flash://ADMIN_DIRssh/ knownhosts file. Example Dell#show ip ssh client-pub-keys poclab4,123.12.1.
PAGE 1420
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. Usage Information This command displays the contents of the flash:/ADMIN_DIR/ssh/ authorized-keys.username file.
PAGE 1421
ipv6-address prefix-length (OPTIONAL) Enter the IPv6 address in the x:x:x:x::x format then the prefix length in the /x format. The range is from /0 to /128. NOTE: The :: notation specifies successive hexadecimal fields of zeros. -c encryption cipher Enter the following encryption cipher. (For v2 clients only.): • 3des-cbc: Force ssh to use 3des-cbc encryption cipher. -l username (OPTIONAL) Enter the keyword -l then the user name used in this SSH session.
PAGE 1422
Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Added IPv6 support. Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. Usage Information Dell Networking OS supports both inbound and outbound SSH sessions using IPv4 or IPv6 addressing. Inbound SSH supports accessing the system through the management interface as well as through a physical Layer 3 interface. Example Dell#ssh 10.11.8.
PAGE 1423
Related Commands Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the C-Series and S-Series. show ip dhcp snooping — displays the contents of the DHCP binding table. ip dhcp relay Enable Option 82. Z9000 Syntax Parameters ip dhcp relay information-option [trust-downstream trustdownstream Configure the system to trust Option 82 when it is received from the previous-hop router.
PAGE 1424
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.
PAGE 1425
• For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE. slot/port Enter the slot and port number of the interface. lease time Enter the keyword lease then the amount of time the IP address is leased. The range is from 1 to 4294967295. Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1426
Introduced on the Z9500. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the C-Series and S-Series. ip dhcp snooping database renew Renew the binding table. Z9000 Syntax ip dhcp snooping database renew Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific.
PAGE 1427
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the C-Series and S-Series.
PAGE 1428
Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.
PAGE 1429
Version 7.8.1.0 Related Commands Security Introduced on the C-Series and S-Series. clear ip dhcp snooping — clears the contents of the DHCP binding table.
PAGE 1430
PAGE 1431
Service Provider Bridging 46 Service provider bridging is composed of virtual local area network (VLAN) Stacking, Layer 2 Protocol Tunneling, and Provider Backbone Bridging as described in the Dell Networking OS Configuration Guide Service Provider Bridging chapter. This chapter includes command line information (CLI) for the Dell Networking operating software Layer 2 Protocol Tunneling (L2PT). L2PT enables protocols to tunnel through an 802.1q tunnel.
PAGE 1432
• For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. in | out | both Enter the keyword in, out, or both to debug incoming interfaces, outgoing interfaces, or both incoming and outgoing interfaces.
PAGE 1433
Parameters rate-limit rate Enter the keyword rate-limit followed by a number for the rate-limit for tunneled packets on the VMAN. The range is from 64 to 320. stp Enter the keyword stp to enable protocol tunneling on a spanning tree, including STP, MSTP, RSTP, and PVST. Defaults none Command Modes CONF-IF-VLAN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guid.
PAGE 1434
Defaults The default destination MAC is 01:01:e8:00:00:00. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.
PAGE 1435
Usage Information Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.4.1.0 Introduced Dell Networking OS must have the default CAM profile with the default microcode before you enable L2PT. protocol-tunnel rate-limit Enable traffic rate limiting per box. Z-Series Syntax protocol-tunnel rate-limit rate To reset the rate limit to the default, use the no protocol-tunnel rate-limit rate command. Parameters rate Enter the rate in frames per second.
PAGE 1436
Related Commands show protocol-tunnel — displays tunneling information for all VLANs. show running-config — displays the current configuration. show protocol-tunnel Display protocol tunnel information for all or a specified VLAN-Stack VLAN. Z-Series Syntax Parameters show protocol-tunnel [vlan vlan-id] vlan vlan-id (OPTIONAL) Enter the keyword vlan then the VLAN ID to display information for the one VLAN. The range is from 1 to 4094.
PAGE 1437
Gi1/2 Dell# Related Commands 2 STP, PVST show running-config — displays the current configuration.
PAGE 1438
PAGE 1439
sFlow 47 The Dell Networking operating software (OS) supports sFlow commands on the Z-Series platform. Dell Networking operating software sFlow monitoring system includes an sFlow Agent and an sFlow Collector. • The sFlow Agent combines the flow samples and interface counters into sFlow datagrams and forwards them to the sFlow Collector. • The sFlow Collector analyses the sFlow Datagrams received from the different devices and produces a network-wide view of traffic flows.
PAGE 1440
sflow collector Configure a collector device to which sFlow datagrams are forwarded. Z-Series Syntax sflow collector {ip-address | ipv6-address} agent-addr {ipaddress | ipv6-address} [number [max-datagram-size number]] | [max-datagram-size number] [vrf management] To delete a configured collector, use the no sflow collector {ip-address | ipv6-address} agent-addr {ipv4-address | ipv6-address} [number [max-datagram-size number]] | [max-datagram-size number] [vrf management] command.
PAGE 1441
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.4.2.3 Added support for IPv6 sFlow collectors and agents on the E-series TeraScale, C-Series, and S-Series. Version 8.4.1.1 Added support for IPv6 sFlow collectors and agents on the E-series ExaScale. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced S-Series Stacking. Version 8.1.1.0 Introduced on the E-Series ExaScale.
PAGE 1442
sflow enable (Global) Enable sFlow globally. Z-Series Syntax sflow enable To disable sFlow, use the no sflow enable command. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 1443
Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.
PAGE 1444
Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.
PAGE 1445
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced on S-Series Stacking.
PAGE 1446
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced on S-Series Stacking.
PAGE 1447
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced on S-Series Stacking.
PAGE 1448
Defaults The Global default sampling. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.
PAGE 1449
• For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a Port-Channel Ethernet interface, enter the keyword port-channel then the slot/port information. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific.
PAGE 1450
Gi 3/40: configured rate 16384, actual rate 16384, subsampling rate 1 Dell# show sflow linecard Display the sFlow information on a line card. Z-Series Syntax Parameters show sflow linecard {slot number} slot number (OPTIONAL) Enter a slot number to view information on the line card in that slot. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1451
48 Simple Network Management Protocol (SNMP) and Syslog This chapter contains commands to configure and monitor the simple network management protocol (SNMP) v1/v2/v3 and Syslog. Both features are supported on the Z-Series platform. The chapter contains the following sections: • SNMP Commands • Syslog Commands SNMP Commands The following SNMP commands are available in the Dell Networking operating software.
PAGE 1452
show snmp Display the status of SNMP network elements. Z-Series Syntax show snmp Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000.
PAGE 1453
show snmp engineID Display the identification of the local SNMP engine and all remote engines that are configured on the router. Z-Series Syntax show snmp engineID Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.
PAGE 1454
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.
PAGE 1455
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series.
PAGE 1456
> snmpwalk -c public 10.10.10.130 .1.3.6.1.2.1.31 | grep -i alias | more IF-MIB::ifAlias.134530304 = STRING: This is a port connected to Router2. This is a port connected to IF-MIB::ifAlias.134792448 = STRING: !------command run on Dell Networkingswitch: --------------! Dell#snmp ifmib ifalias long !------command run on server connected to switch: --------------! > snmpwalk -c public 10.10.10.130 .1.3.6.1.2.1.31 | grep -i alias | more IF-MIB::ifAlias.134530304 = STRING: This is a port connected to Router2.
PAGE 1457
Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.
PAGE 1458
NOTE: For IPv6 ACLs, only IPv6 and UDP types are valid for SNMP; TCP and ICMP rules are not valid for SNMP. In IPv6 ACLs, port rules are not valid for SNMP. Example Dell#config Dell(conf)# snmp-server community public ro Dell(conf)# snmp-server community guest ro security-name guestuser Dell(conf)# Example Dell(conf)# ip access-list standard snmp-ro-acl Dell(config-std-nacl)#seq 5 permit host 10.10.10.
PAGE 1459
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series legacy command snmp-server enable traps Enable SNMP traps. Z-Series Syntax snmp-server enable traps [notification-type] [notificationoption] To disable traps, use the no snmp-server enable traps [notificationtype] [notification-option] command.
PAGE 1460
• supply • temperature For the snmp notification-type, enter one of the following optional parameters: • authentication • coldstart • linkdown • linkup Defaults Not enabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000.
PAGE 1461
snmp-server engineID Configure the name for both the local and remote SNMP engines on the router. Z-Series Syntax snmp-server engineID [local engineID] [remote ip-address udpport port-number engineID] To return to the default, use the no snmp-server engineID [local engineID] [remote ip-address udp-port port-number engineID] command. Parameters local engineID Enter the keyword local followed by the engine ID number that identifies the copy of the SNMP on the local device.
PAGE 1462
Version 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information Changing the value of the SNMP Engine ID has important side effects. A user’s password (entered on the command line) is converted to a message digest algorithm (MD5) or secure hash algorithm (SHA) security digest. This digest is based on both the password and the local Engine ID. The command line password is then destroyed, as required by RFC 2274.
PAGE 1463
• 3 is the most secure of the security modes. • 2c allows transmission of informs and counter 64, which allows for integers twice the width of what is normally allowed. The default is 1. auth (OPTIONAL) Enter the keyword auth to specify authentication of a packet without encryption. noauth (OPTIONAL) Enter the keyword noauth to specify no authentication of a packet. priv (OPTIONAL) Enter the keyword priv to specify both authentication and then scrambling of the packet.
PAGE 1464
Version 8.3.11.1 Introduced on the Z9000. Version 8.3.10.2 Added support for the access parameter. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information The following Example specifies the group named harig as a version 3 user requiring both authentication and encryption and read access limited to the read named rview.
PAGE 1465
traps (OPTIONAL) Enter the keyword traps to send trap notifications to the specified host. The default is traps. informs (OPTIONAL) Enter the keyword informs to send inform notifications to the specified host. The default is traps. version 1 | 2c | 3 (OPTIONAL) Enter the keyword version to specify the security model then the security model version number 1, 2c, or 3: • Version 1 is the least secure version. • Version 3 is the most secure of the security modes.
PAGE 1466
• isis — Enable ISIS adjacency change traps • pfc — Enable pfc traps • snmp — Enable SNMP trap • stp — Enable 802.1d state change traps • vlt — Enable VLT traps • vrrp — Enable VRRP state change traps • xstp — Enable 802.1s, 802.1w, and PVST+ state change traps The default is all trap types are sent to host. Defaults As above. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1467
When multiple snmp-server host commands are given for the same host and type of notification (trap or inform), each succeeding command overwrites the previous command. Only the last snmp-server host command will be in effect. For example, if you enter an snmp-server host inform command for a host and then enter another snmp-server host inform command for the same host, the second command replaces the first command. The snmp-server host command is used with the snmp-server enable command.
PAGE 1468
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.
PAGE 1469
Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series legacy command snmp-server trap-source Configure a specific interface as the source for SNMP traffic. Z9000 Syntax snmp-server trap-source interface To disable sending traps out a specific interface, use the no snmp trap-source command.
PAGE 1470
Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information To enable this snmp-server trap-source command, configure an IP address on the interface and enable the interface configured as an SNMP trap source. Related Commands snmp-server community — sets the community string.
PAGE 1471
1 | 2c | 3 (OPTIONAL) Enter the security model version number (1, 2c, or 3): • 1 is the least secure version. • 3 is the most secure of the security modes. • 2c allows transmission of informs and counter 64, which allows for integers twice the width of what is normally allowed. The default is 1. encrypted (OPTIONAL) Enter the keyword encrypted to specify the password appear in encrypted format (a series of digits, masking the true characters of the string).
PAGE 1472
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000.
PAGE 1473
Example Dell#conf Dell(conf)# snmp-server user n3user ngroup remote 172.31.1.3 udp-port 5009 3 auth md5 authpasswd Related Commands show snmp user — displays the information configured on each SNMP user name. snmp-server user (for AES128-CFB Encryption) Specify that AES128-CFB encryption algorithm needs to be used for transmission of SNMP information. The Advanced Encryption Standard (AES) Cipher Feedback (CFB) 128-bit encryption algorithm is in compliance with RFC 3826.
PAGE 1474
Command History Usage Information Version 9.3(0.0) Added support for the AES128-CFB encryption algorithm on the S4820T, S4810, S6000 and Z-Series platforms To enable robust, effective protection and security for SNMP packets transferred between the server and the client, you can use the snmp-server user username group groupname 3 auth authentication-type authpassword priv aes128 priv-password to specify that AES128-CFB encryption algorithm needs to be used.
PAGE 1475
Usage Information Use this command to bind an SNMP agent to a VRF. The SNMP agent processes the requests from the interfaces that belong to the specified VRF. If no VRF is specified, then the default VRF is used. Related Commands show snmp user — displays the information configured on each SNMP user name. snmp-server view Configure an SNMPv3 view.
PAGE 1476
E-Series legacy command Usage Information The oid-tree variable is a full sub-tree starting from 1.3.6 and cannot specify the name of a sub-tree or a MIB. The following Example configures a view named rview that allows access to all objects under 1.3.6.1. Example Dell# conf Dell#(conf) snmp-server view rview 1.3.6.1 included Related Commands show running-config snmp — displays the SNMP running configuration.
PAGE 1477
Syslog Commands The following commands allow you to configure logging functions on all Dell Networking switches. clear logging Clear the messages in the logging buffer. Z-Series Syntax clear logging Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.
PAGE 1478
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series.
PAGE 1479
Related Commands logging console — sets the logging console parameters. default logging monitor Return to the default settings for messages logged to the terminal. Z-Series Syntax default logging monitor Defaults level = 7 or debugging Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1480
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.
PAGE 1481
Version 9.0.2.0 Introduced on the S6000. Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.4.1.0 Added support for IPv6. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series.
PAGE 1482
Defaults level = 7; size = 40960 bytes Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 1483
errors, warnings, notifications, informational, or debugging. The default is 7 or debugging. Defaults level = 7; size = debugging Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 9.2(0.0) Introduced on the M I/O Aggregator.
PAGE 1484
• deamon (system deamons) • kern (kernel) • local0 (local use) • local1 (local use) • local2 (local use) • local3 (local use) • local4 (local use) • local5 (local use) • local6 (local use) • local7 (local use) • lpr (line printer system) • mail (mail system) • news (USENET news) • sys9 (system use) • sys10 (system use) • sys11 (system use) • sys12 (system use) • sys13 (system use) • sys14 (system use) • syslog (Syslog process) • user (user process) • uucp (Unix to
PAGE 1485
E-Series legacy command Related Commands logging — enables logging to a Syslog server. logging on — enables logging. logging history Specify which messages are logged to the history table of the switch and the SNMP network management station (if configured). Z-Series Syntax logging history level To return to the default values, use the no logging history command.
PAGE 1486
Related Commands show logging — displays information logged to the history buffer. logging history size Specify the number of messages stored in the Dell Networking logging history table. Z-Series Syntax logging history size size To return to the default values, use the no logging history size command. Parameters size Indicate a value as the number of messages to be stored. The range is from 0 to 500. The default is 1 message.
PAGE 1487
logging monitor Specify which messages are logged to Telnet applications. Z-Series Syntax logging monitor [level] To disable logging to terminal connections, use the no logging monitor command. Parameters level Indicate a value from 0 to 7 or enter one of the following parameters: emergencies, alerts, critical, errors, warnings, notifications, informational, or debugging. The default is 7 or debugging.
PAGE 1488
logging on Specify that debug or error messages are asynchronously logged to multiple destinations, such as the logging buffer, Syslog server, or terminal lines. Z-Series Syntax logging on To disable logging to logging buffer, Syslog server and terminal lines, use the no logging on command. Defaults Enabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1489
logging source-interface Specify that the IP address of an interface is the source IP address of Syslog packets sent to the Syslog server. Z9000 Syntax logging source-interface interface To disable this command and return to the default setting, use the no logging source-interface command. Parameters interface Enter the following keywords and slot/port or number information: • For a 100/1000 Ethernet interface, enter the keyword GigabitEthernet then the slot/port information.
PAGE 1490
Version 8.3.7.0 Introduced on the S4810. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information Syslog messages contain the IP address of the interface used to egress the router. By configuring the logging source-interface command, the Syslog packets contain the IP address of the interface configured.
PAGE 1491
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information When you enable logging synchronous, unsolicited messages appear between software prompts and outputs. Only the messages with a severity at or below the set level are sent to the console.
PAGE 1492
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series, S55. Version 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information To block a type of message parameter, set the logging trap level to a lower number. For example, to block severity messages at level 6, set the level to 5.
PAGE 1493
Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series.
PAGE 1494
Oct 8 09:26:25: %RPM1:RP1 %BGP-5-ADJCHANGE: Connection with neighbor 1.1.14.2 closed. Neighbor recycled --More-Example (History) Dell#show logging history Syslog History Table: 1 maximum table entries, saving level Warnings or higher SNMP notifications not Enabled %RPM:0:0 %CHMGR-2-LINECARDDOWN - Line card 3 down - IPC timeout Dell# show logging driverlog stack-unit Display the driver log for the specified stack member.
PAGE 1495
terminal monitor Configure the Dell Networking OS to display messages on the monitor/terminal. Z-Series Syntax terminal monitor To return to default settings, use the terminal no monitor command. defaults Disabled. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1496
PAGE 1497
49 SNMP Traps This chapter lists the traps sent by the Dell Networking operating software. Each trap is listed by the fields Message ID, Trap Type, and Trap Option. Message ID Trap Type Trap Option COLD_START SNMP COLDSTART WARM_START SNMP WARMSTART COPY_CONFIG_COMPLETE SNMP NONE SNMP LINKDOWN SNMP LINKUP SNMP AUTH EGP_NEIGHBOR_LOSS SNMP NONE OSTATE_DOWN SNMP LINKDOWN SNMP LINKUP SNMP NONE SNMP NONE %SNMP-5-SNMP_COLD_START: SNMP COLD_START trap sent.
PAGE 1498
Message ID Trap Type Trap Option SNMP NONE SNMP NONE NONE NONE ENVMON NONE ENVMON NONE ENVMON NONE CHM_CARD_PROBLEM ENVMON NONE CHM_ALARM_CUTOFF ENVMON NONE CHM_SFM_UP ENVMON NONE CHM_SFM_DOWN ENVMON NONE CHM_RPM_UP ENVMON NONE ENVMON NONE ENVMON NONE %RPM0-P:CP %SNMP-4-RMON_FALLING_THRESHOLD: RMON falling threshold alarm from SNMP OID RMON_HC_RISHING_THRESHOLD %RPM0-P:CP %SNMP-4-RMON_HC_RISING_THRESHOLD: RMON high-capacity rising threshold alarm from SNMP OID R
PAGE 1499
Message ID Trap Type Trap Option ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON SUPPLY ENVMON SUPPLY ENVMON SUPPLY ENVMON SUPPLY ENVMON SUPPLY ENVMON SUPPLY ENVMON TEMP ENVMON TEMP %RAM-5-FAST_FAILOVER: RPM Failover Completed CHM_SFM_ADD %TSM-5-SFM_DISCOVERY: Found SFM 1 CHM_SFM_REMOVE %TSM-5-SFM_REMOVE: Removed SFM 1 CHM_MAJ_SFM_DOWN %CHMGR-0-MAJOR_SFM: Major alarm: Switch fabric down CHM_MAJ_SFM_DOWN_CLR %CHMGR-5-MAJOR_SFM_CLR: Major alarm cle
PAGE 1500
Message ID Trap Type Trap Option ENVMON TEMP ENVMON TEMP ENVMON FAN ENVMON FAN ENVMON FAN ENVMON FAN ENVMON NONE ENVMON NONE %CHMRG-5-MINOR_TEMP_CLR: Minor alarm cleared: chassis temperature normal (%s %d temperature is within threshold of %dC) CHM_MAJ_ALRM_TEMP %CHMGR-2-MAJOR_TEMP: Major alarm: chassis temperature high (%s temperature reaches or exceeds threshold of %dC) CHM_MAJ_ALRM_TEMP_CLR %CHMGR-2-MAJOR_TEMP_CLR: Major alarm cleared: chassis temperature lower (%s %d temperature is wi
PAGE 1501
Message ID Trap Type Trap Option ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE PROTO NONE PROTO NONE PROTO NONE PROTO NONE PROTO NONE %TME-2-ABNORMAL_TASK_TERMINATION: CRASH - task:%s %s CHM_CPU_THRESHOLD %CHMGR-5-CPU_THRESHOLD: Cpu %s usage above threshold. Cpu5SecUsage (%d) CHM_CPU_THRESHOLD_CLR %CHMGR-5-CPU_THRESHOLD_CLR: Cpu %s usage drops below threshold. Cpu5SecUsage (%d) CHM_MEM_THRESHOLD %CHMGR-5-MEM_THRESHOLD: Memory %s usage above threshold.
PAGE 1502
PAGE 1503
50 Stacking All commands in this chapter are specific to the Dell Networking operating software on the Z9000 platform. The commands are always available and operational, whether the S-Series has a stacking module inserted. You can use the commands to pre-configure a switch, so that the configuration settings are invoked when the switch is attached to other S-Series units.
PAGE 1504
Version 8.3.19.0 Introduced on the S4820T. Version 8.3.7.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.1.0 Added the members option. Version 7.7.1.0 Introduced on the S-Series. Usage Information The range is 0 to 11. Enabling this command keeps the failed switch in the Failed state. The switch does not reboot until it is manually rebooted. When enabled, it is not displayed in the running-config. When disabled, it is displayed in the runningconfig.
PAGE 1505
redundancy protocol Enable hitless failover for a protocol. Z9000 Syntax Protocols redundancy protocol lacp Enter the LACP protocol xstp Enter one of the following protocols: STP, RSTP, MSTP, PVST. Defaults Not enabled. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1506
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.7.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.1.0 Added the hard reset option. Version 7.8.1.
PAGE 1507
show redundancy Display the current redundancy configuration (status of automatic reboot configuration on stack management unit). Z9000 Syntax show redundancy Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Example Version 8.3.19.
PAGE 1508
Stack-unit SW Version: 7.7.1.
PAGE 1509
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.7.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 7.7.1.0 Introduced on the S-Series. The following describes the show interfaces command shown in the following example. Field Description Topology Lists the topology of stack ports connected: Ring, Daisy chain, or Standalone. Interface The unit/port ID of the connected stack port on this unit.
PAGE 1510
---------------------0/49 1/49 0/50 0/51 2/49 1/49 0/49 1/50 2/51 2/49 0/51 2/51 1/50 2/52 Dell# Related Commands • reset stack-unit – resets the designated stack member. • show hardware stack-unit – displays the data plane or management plane input and output statistics of the designated component of the designated stack member. • show system (S-Series and Z-Series) – displays the current status of all stack members or a specific member.
PAGE 1511
Related Commands Version 8.3.7.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 7.7.1.0 Introduced on the S-Series. • reload – reboots Dell Networking OS. stack-unit provision Preconfigure a logical stacking ID of a switch that joins the stack. This is an optional command that is executed on the management unit.
PAGE 1512
• show system (S-Series and Z-Series) – displays the status of all stack members or a specific member. stack-unit stack-group Configure the stacking unit and stacking group by specifying an ID when adding units to a stack to ensure the unit is assigned to the correct group. Syntax stack-unit unit-id stack-group stack-group-id To remove the current stack group configuration, use the no stack-unit unitid stack-group stack-id command. Parameters unit-id Enter the stack unit ID.
PAGE 1513
upgrade system stack-unit Copy the boot image or Dell Networking OS from the management unit to one or more stack members. Z9000 Syntax Parameters upgrade {boot | system} stack-unit {all | 0-11 | A | B} boot Enter the keyword boot to copy the boot image from the management unit to the designated stack members. system Enter the keyword system to copy the Dell Networking OS image from the management unit to the designated stack members. stack-unit Enter the stack-unit number.
PAGE 1514
• 1514 show version — displays the current Dell Networking OS version information on the system.
PAGE 1515
Storm Control 51 The Dell Networking operating software storm control feature allows you to limit or suppress traffic during a traffic storm (Broadcast/Unknown Unicast Rate Limiting or Multicast on the C-Series and SSeries). Storm control is supported on the Dell Networking Z-Series platforms. Important Points to Remember • Interface commands can only be applied on physical interfaces (virtual local area networks [VLANs] and link aggregation group [LAG] interfaces are not supported).
PAGE 1516
show storm-control broadcast Display the storm control broadcast configuration. Z9000 Syntax Parameters show storm-control broadcast [interface] interface Defaults none Command Modes • EXEC • EXEC Privilege Command History (OPTIONAL) Enter one of the following interfaces to display the interface-specific storm control configuration: • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet followed by the slot/ port information.
PAGE 1517
show storm-control multicast Display the storm control multicast configuration. Z9000 Syntax Parameters show storm-control multicast [interface] interface Defaults none Command Modes • EXEC • EXEC Privilege Command History (OPTIONAL) Enter one of the following interfaces to display the interface specific storm control configuration: • For Fast Ethernet, enter the keyword Fastethernet then the slot/port information.
PAGE 1518
show storm-control unknown-unicast Display the storm control unknown-unicast configuration. Z-Series Syntax Parameters show storm-control unknown-unicast [interface] interface Defaults none Command Modes • EXEC • EXEC Privilege Command History (OPTIONAL) Enter one of the following interfaces to display the interface specific storm control configuration: • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then y the slot/port information.
PAGE 1519
storm-control broadcast (Configuration) Configure the percentage of broadcast traffic allowed in the network. Z-Series Syntax storm-control broadcast [packets_per_second in] To disable broadcast rate-limiting, use the no storm-control broadcast [packets_per_second in] command. Parameters percentagedeci mal_value in | out Enter the percentage of broadcast traffic allowed in or out of the network. Optionally, you can designate a decimal value percentage, for example, 55.5%. The decimal range is from .
PAGE 1520
storm-control broadcast (Interface) Configure the percentage of broadcast traffic allowed on an interface (ingress only). Z-Series Syntax storm-control broadcast [packets_per_second in] To disable broadcast storm control on the interface, use the no storm-control broadcast [packets_per_second in] command. Parameters packets_per_se cond in Enter the packets per second of broadcast traffic allowed into the network. The range is from 0 to 33554368.
PAGE 1521
storm-control multicast (Configuration) Configure the packets per second (pps) of multicast traffic allowed into the C-Series and S-Series networks only. Z-Series Syntax storm-control multicast packets_per_second in To disable storm-control for multicast traffic into the network, use the no stormcontrol multicast packets_per_second in command. Parameters packets_per_se cond in Enter the packets per second of multicast traffic allowed into the network. The range is from 0 to 33554368.
PAGE 1522
storm-control multicast (Interface) Configure the percentage of multicast traffic allowed on an C-Series or S-Series interface (ingress only) network only. Z-Series Syntax storm-control multicast packets_per_second in To disable multicast storm control on the interface, use the no storm-control multicast packets_per_second in command. Parameters packets_per_se cond in Enter the packets per second of broadcast traffic allowed into the network. The range is from 0 to 33554368.
PAGE 1523
Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.
PAGE 1524
• 100% allows all traffic into the interface. The decimal range is from 0.1 to 0.9. wred-profile name E-Series Only: (Optionally) Enter the keywords wredprofile followed by the profile name to designate a wredprofile. packets_per_se cond in C-Series and S-Series Only: Enter the packets per second of broadcast traffic allowed into the network. The range is from 0 to 33554431. Defaults none Command Modes INTERFACE (conf-if-interface-slot/port) Command History This guide is platform-specific.
PAGE 1525
Spanning Tree Protocol (STP) 52 The commands in this chapter configure and monitor the IEEE 802.1d spanning tree protocol (STP) and are supported on the Z-Series Dell Networking switch/routing platform. bridge-priority Set the bridge priority of the switch in an IEEE 802.1D spanning tree. Z-Series Syntax bridge-priority {priority-value | primary | secondary} To return to the default value, use the no bridge-priority command. Parameters priority-value Enter a number as the bridge priority value.
PAGE 1526
pre-Version 6.2.1.1 Introduced on the E-Series. bpdu-destination-mac-address Use the Provider Bridge Group address in Spanning Tree or GVRP PDUs. Syntax Parameters bpdu-destination-mac-address [stp | gvrp] provider-bridge-group xstp Force STP, RSTP, and MSTP to use the Provider Bridge Group address as the destination MAC address in its BPDUs. gvrp Forces GVRP to use the Provider Bridge GVRP Address as the destination MAC address in its PDUs.
PAGE 1527
Parameters stp-id Enter zero (0). The switch supports one spanning tree group with a group ID of 0. protocol Enter the keyword for the type of STP to debug, either mstp, pvst, or rstp. all (OPTIONAL) Enter the keyword all to debug all spanning tree operations. bpdu (OPTIONAL) Enter the keyword bpdu to debug bridge protocol data units. config (OPTIONAL) Enter the keyword config to debug configuration information. events (OPTIONAL) Enter the keyword events to debug STP events.
PAGE 1528
description Enter a description of the spanning tree. Z-Series Syntax description {description} To remove the description from the spanning tree, use the no description {description} command. Parameters description Enter a description to identify the spanning tree (80 characters maximum). Defaults none Command Modes SPANNING TREE (The prompt is “config-stp”.) Command History This guide is platform-specific.
PAGE 1529
Command Modes SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.
PAGE 1530
Related Commands Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. max-age — changes the wait time before STP refreshes protocol configuration information. hello-time — changes the time interval between BPDUs.
PAGE 1531
Related Commands Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. forward-delay — changes the wait time before STP transitions to the Forwarding state. max-age — changes the wait time before STP refreshes protocol configuration information. max-age To maintain configuration information before refreshing that information, set the time interval for the spanning tree bridge.
PAGE 1532
Related Commands Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. forward-delay — changes the wait time before STP transitions to the Forwarding state. hello-time — changes the time interval between BPDUs. protocol spanning-tree To enable and configure the spanning tree group, enter SPANNING TREE mode. Z-Series Syntax protocol spanning-tree stp-id To disable the Spanning Tree group, use the no protocol spanning-tree stp-id command.
PAGE 1533
Usage Information STP is not enabled when you enter SPANNING TREE mode. To enable STP globally on the switch, use the no disable command from SPANNING TREE mode. Example Dell(conf)#protocol spanning-tree 0 Dell(config-stp)# Related Commands disable — disables spanning tree group 0. To enable spanning tree group 0, use the no disable command. show config Display the current configuration for the mode. Only non-default values display.
PAGE 1534
show spanning-tree 0 Display the spanning tree group configuration and status of interfaces in the spanning tree group. Z9000 Syntax Parameters show spanning-tree 0 [active | brief | guard | interface interface | root | summary] 0 Enter 0 (zero) to display information about that specific spanning tree group. active (OPTIONAL) Enter the keyword active to display only active interfaces in spanning tree group 0.
PAGE 1535
Usage Information Version 8.4.2.1 Added support for the optional guard keyword on the CSeries, S-Series, and E-Series TeraScale. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. Enable spanning tree group 0 prior to using this command. The following describes the show spanning-tree 0 command shown in the example. Field Description “Bridge Identifier...
PAGE 1536
Example Dell#show spann 0 Executing IEEE compatible Spanning Tree Protocol Bridge Identifier has priority 32768, Address 0001.e800.0a56 Configured hello time 2, max age 20, forward delay 15 We are the root of the spanning tree Current root has priority 32768 address 0001.e800.
PAGE 1537
Usage Information Example (Guard) The following describes the show spanning-tree 0 guard command shown in the example. Field Description Interface Name STP interface. Instance STP 0 instance. Sts Port state: root-inconsistent (INCON Root), forwarding (FWD), listening (LIS), blocking (BLK), or shut down (EDS Shut). Guard Type Type of STP guard configured (Root, Loop, or BPDU guard).
PAGE 1538
portfast [bpduguard [shutdown-onviol ation]] Enter the keyword portfast to enable Portfast to move the interface into Forwarding mode immediately after the root fails. Enter the optional keyword bpduguard to disable the port when it receives a BPDU. Enter the optional keyword shutdown-on-violation to hardware disable an interface when a BPDU is received and the port is disabled. priority priority Enter keyword priority then a number as the priority. The range is from zero (0) to 15. The default is 8.
PAGE 1539
Protocol (RSTP), Multiple Spanning Tree Protocol (MSTP), and Per-VLAN Spanning Tree Plus (PVST+). Root guard is supported on any STP-enabled port or port-channel except when used as a stacking port. When enabled on a port, root guard applies to all VLANs configured on the port. STP root guard and loop guard cannot be enabled at the same time on a port.
PAGE 1540
PAGE 1541
System Time and Date 53 The commands in this chapter configure time values on the system, either using the Dell Networking operating software, or the hardware, or using the network time protocol (NTP). With NTP, the switch can act only as a client to an NTP clock host. For more information, refer to the “Network Time Protocol” section of the Management chapter in the Dell Networking OS Configuration Guide.
PAGE 1542
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. You can change the order of the month and day parameters to enter the time and date as time day month year. In the switch, the hardware clock is separate from the software and is called the calendar.
PAGE 1543
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. In the switch, the hardware clock is separate from the software and is called the calendar. This hardware clock runs continuously.
PAGE 1544
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.11.1 Introduced on the Z9000. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series.
PAGE 1545
start-day Enter the number of the day. The range is from 1 to 31. You can enter the name of a month to change the order of the display to time day month year. start-year Enter a four-digit number as the year. The range is from 1993 to 2035. start-time Enter the time in hours:minutes. For the hour variable, use the 24-hour format; example, 17:15 is 5:15 pm. end-day Enter the number of the day. The range is from 1 to 31.
PAGE 1546
clock summer-time recurring — sets a date (and time zone) on which to convert the switch to daylight saving time each year. show clock — displays the current clock settings. clock summer-time recurring Set the software clock to convert to daylight saving time on a specific day each year.
PAGE 1547
• last: enter the keyword last to end daylight saving time in the last week of the month. end-day Enter the weekday name that you want daylight saving time to end. Enter the weekdays using the three letter abbreviations; for example Sun, Sat, Mon, and so on. The range is from Sun to Sat. end-month Enter the name of one of the 12 months in English. end-time Enter the time in hours:minutes:seconds. For the hour variable, use the 24-hour format; example, 17:15:00 is 5:15 pm.
PAGE 1548
clock timezone Configure a timezone for the switch. Z-Series Syntax clock timezone timezone-name offset To delete a timezone configuration, use the no clock timezone command. Parameters timezonename Enter the name of the timezone. You cannot use spaces. offset Enter one of the following: • a number from 1 to 23 as the number of hours in addition to universal time coordinated (UTC) for the timezone. • a minus sign (-) then a number from 1 to 23 as the number of hours. Defaults Not configured.
PAGE 1549
clock update-calendar Set the switch hardware clock based on the software clock. Z-Series Syntax clock update-calendar Defaults Not configured. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.11.
PAGE 1550
all Enter the keyword all to display information on all NTP transactions. authentication Enter the keyword authentication to display information on NTP authentication transactions. events Enter the keyword events to display information on NTP events. loopfilter Enter the keyword loopfilter to display information on NTP local clock frequency. packets Enter the keyword packets to display information on NTP packets. select Enter the keyword select to display information on the NTP clock selection.
PAGE 1551
Defaults Not enabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.
PAGE 1552
Defaults NTP authentication is not configured by default. If you do not specify the option [0 | 7], 0 is selected by default. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.11.
PAGE 1553
Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.
PAGE 1554
Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. ntp multicast client To receive NTP information from the network via multicast, configure the switch. Z-Series Syntax ntp multicast client [multicast-address] To disable multicast reception, use the no ntp multicast client [multicast-address] command. Parameters multicastaddress (OPTIONAL) Enter a multicast address.
PAGE 1555
pre-Version 6.1.1.0 Introduced on the E-Series. ntp server Configure an NTP time-serving host. Z-Series Syntax Parameters ntp server {hostname | ipv4-address | ipv6-address} [key keyid] [prefer] [version number] ipv4-address | ipv6-address Enter an IPv4 address (A.B.C.D) or IPv6 address (X:X:X:X::X). hostname Enter the hostname of the server. key keyid (OPTIONAL) Enter the keyword key and a number as the NTP peer key. The range is from 1 to 4294967295.
PAGE 1556
Usage Information You can configure multiple time-serving hosts (up to 250). From these timeserving hosts, the Dell Networking OS chooses one NTP host with which to synchronize. To determine which server was selected, use the show ntp associations command. Because many polls to NTP hosts can impact network performance, Dell Networking recommends limiting the number of hosts configured. Related Commands show ntp associations — displays the NTP servers configured and their status.
PAGE 1557
Version 9.0.2.0 Introduced on the S6000. Version 8.3.11.1 Introduced on the Z9000. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. ntp trusted-key Set a key to authenticate the system to which NTP synchronizes. Z-Series Syntax ntp trusted-key number To delete the key, use the no ntp trusted-key number command.
PAGE 1558
Related Commands ntp authentication-key — sets an authentication key for NTP. ntp authenticate — enables the NTP authentication parameters you set. ntp update-calendar Configure the Dell Networking OS to update the calendar (the hardware clock) with the NTP-derived time. Z-Series Syntax ntp update-calendar [minutes] To return to default setting, use the no ntp update-calendar command. Parameters minutes (OPTIONAL) Enter the number of minutes between updates from NTP to the hardware clock.
PAGE 1559
show calendar Display the current date and time based on the switch hardware clock. Z-Series Syntax show calendar Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.
PAGE 1560
Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.
PAGE 1561
• Command History EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information System Time and Date Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.
PAGE 1562
Field Description disp Displays the dispersion. Example Dell#show ntp associations remote ref clock st when poll reach delay offset disp ============================================================= 10.10.120.5 0.0.0.0 16 - 256 0 0.00 0.000 16000.0 *172.16.1.33 127.127.1.0 11 6 16 377 -0.08 -1499.9 104.16 172.31.1.33 0.0.0.0 16 - 256 0 0.00 0.000 16000.0 192.200.0.2 0.0.0.0 16 - 256 0 0.00 0.000 16000.
PAGE 1563
Usage Information The following describes the show ntp status command shown in the Example below. Field Description “Clock is...” States whether or not the switch clock is synchronized, which NTP stratum the system is assigned and the IP address of the NTP peer. “frequency is...” Displays the frequency (in ppm), stability (in ppm) and precision (in Hertz) of the clock in this system. “reference time is...” Displays the reference time stamp. “clock offset is...
PAGE 1564
PAGE 1565
54 Tunneling Tunneling is supported on the Z9000 platform. tunnel-mode Enable a tunnel interface. Z9000 Syntax tunnel mode {ipip | ipv6 | ipv6ip}[decapsulate-any] To disable an active tunnel interface, use the no tunnel mode command. Parameters ipip Enable tunnel in RFC 2003 mode and encapsulate IPv4 and/or IPv6 datagrams inside an IPv4 tunnel. ipv6 Enable tunnel in RFC 2473 mode and encapsulate IPv4 and/or IPv6 datagrams inside an IPv6 tunnel.
PAGE 1566
Configuration of IPv6 commands over decapsulate-any tunnel causes an error. tunnel source Set a source address for the tunnel. Z9000 Syntax tunnel source {ip-address | ipv6–address | interface-typenumber | anylocal} To delete the current tunnel source address, use the no tunnel source command. Parameters ip-address Enter the source IPv4 address in A.B.C.D format. ipv6–address Enter the source IPv6 address in X:X:X:X::X format.
PAGE 1567
to any IPv4 or IPv6 (depending on the tunnel mode) address configured on the switch that is operationally Up. tunnel keepalive Configure the tunnel keepalive target, interval and attempts. Z9000 Syntax tunnel keepalive {ip-address | ipv6-address}[interval {seconds}] [attempts {count | unlimited}] To disable the tunnel keepalive probes use the no tunnel keepalive command. Parameters ip-address ipv6 address Enter the IPv4 or IPv6 address of the peer to which the keepalive probes will be sent.
PAGE 1568
of the far end tunnel peer, rather than to the tunnel destination. This reduces the chance of both ends of the tunnel staying in keepalive down state. If both ends get into a keepalive down state that does not clear in a few seconds, then performing shutdown - no shutdown sequence on one end should bring both ends back to up. tunnel allow-remote Configure an IPv4 or IPv6 address or prefix whose tunneled packets are accepted for decapsulation.
PAGE 1569
tunnel dscp Configure the method to set the DSCP in the outer tunnel header. Z9000 Syntax tunnel dscp {mapped | } To use the default tunnel mapping behavior, use the no tunnel dscp value command. Parameters mapped Enter the keyword mapped to map the original packet DSCP (IPv4)/Traffic Class (IPv6) to the tunnel header DSCP (IPv4)/ Traffic Class (IPv6) depending on the mode of tunnel. value Enter a value to set the DSCP value in the tunnel header. The range is from 0 to 63.
PAGE 1570
Defaults 0 (Mapped original packet flow-label value to tunnel header flow-label value) Command Modes INTERFACE TUNNEL (conf-if-tu) Command History Usage Information Version 9.3(0.0) Introduced on the S6000, S4810, S4820T, Z9000. This command is only valid for tunnel interfaces with an IPv6 outer header. tunnel hop-limit Configure the method to set the IPv4 time-to-live or the IPv6 hop limit value in the outer tunnel header.
PAGE 1571
tunnel destination Set a destination endpoint for the tunnel. Z9000 Syntax tunnel destination {ip-address | ipv6–address} To delete a tunnel destination address, use the no tunnel destination {ipaddress | ipv6–address} command. Parameters ip-address Enter the destination IPv4 address for the tunnel. ipv6–address Enter the destination IPv6 address for the tunnel. Defaults none Command Modes INTERFACE TUNNEL (conf-if-tu) Command History Usage Information Version 9.3(0.
PAGE 1572
Defaults None Command Modes INTERFACE TUNNEL Command History Usage Information Version 9.4(0.0) Introduced on the S4810, S4820T, S6000 and Z9000. The ip unnumbered command fails in two conditions: • If the logical ip address is configured. • If Tunnel mode is ipv6ip (where ip address over tunnel interface is not possible). To ping the unnumbered tunnels, the logical address route information must be present at both the ends.
PAGE 1573
• If Tunnel mode is ipv6ip (where ip address over tunnel interface is not possible). To ping the unnumbered tunnels, the logical address route information must be present at both the ends. NOTE: The ipv6 unnumbered command can specify an interface name that does not exist or does not have a configured IPv6 address. The tunnel interface is not changed to operationally up until the logical ip address is identified from the one of the address family.
PAGE 1574
PAGE 1575
VLAN Stacking 55 With the virtual local area network (VLAN)-stacking feature (also called stackable VLANs and QinQ), you can “stack” VLANs into one tunnel and switch them through the network transparently. The Dell Networking operating software supports this feature on the Z9000 platform. For more information about basic VLAN commands, refer to the Virtual LAN (VLAN) Commands section in the Layer 2 chapter.
PAGE 1576
dei enable Make packets eligible for dropping based on their DEI value. Z9000 Syntax dei enable Defaults Packets are colored green; no packets are dropped. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 1577
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Introduced on the C-Series and S-Series.
PAGE 1578
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Instroduces on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Introduced on the C-Series and S-Series. Usage Information You must first enable DEI for this configuration to take effect. Related Commands dei enable – Make packets eligible for dropping based on their DEI value. member Assign a stackable VLAN access or trunk port to a VLAN.
PAGE 1579
Version 9.0.2.0 Introduced on the S6000. Version 8.3.11.1 Introduced on the Z9000. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the C-Series and S-Series. E-Series original Command Usage Information You must enable the stackable VLAN (using the vlan-stack compatible command) on the VLAN prior to adding a member to the VLAN. Related Commands vlan-stack compatible — enables stackable VLAN on a VLAN.
PAGE 1580
Usage Information WARNING: The following message displays to confirm the command: All non-default configurations on the related member ports ports () will be removed. Do you want to continue (y/n)? If you enter “y”, all non-default configurations on any member ports of the current stack group is removed when the unit is rebooted. vlan-stack access Specify a Layer 2 port or port channel as an access port to the stackable VLAN network.
PAGE 1581
vlan-stack compatible Enable the stackable VLAN feature on a VLAN. Z9000 Syntax vlan-stack compatible To disable the Stackable VLAN feature on a VLAN, use the no vlan-stack compatible command. Defaults Not configured. Command Modes CONF-IF-VLAN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1582
5 Active Dell# M M M M Gi 13/4 Po1(Gi 13/14-15) Gi 13/18 Gi 13/5 vlan-stack dot1p-mapping Map C-Tag dot1p values to a S-Tag dot1p value. You can separate the C-Tag values by commas and dashed ranges are permitted. Dynamic mode CoS overrides any Layer 2 QoS configuration in case of conflicts.
PAGE 1583
vlan-stack protocol-type Define the stackable VLAN tag protocol identifier (TPID) for the outer VLAN tag (also called the VMAN tag). If you do not configure this command, Dell Networking OS assigns the value 0x9100. Z9000 Syntax Parameters vlan-stack protocol-type number number Enter the hexadecimal number as the stackable VLAN tag. You may specify both bytes of the 2-byte S-Tag TPID. The range is from 0 to FFFF. The default is 9100.
PAGE 1584
Related Commands Number Resulting TPID 81 0x0081 8100 0x8100 portmode hybrid — sets a port (physical ports only) to accept both tagged and untagged frames. A port configured this way is identified as a hybrid port in report displays. vlan-stack trunk — specifies a Layer 2 port or port channel as a trunk port to the Stackable VLAN network. vlan-stack trunk Specify a Layer 2 port or port channel as a trunk port to the Stackable VLAN network.
PAGE 1585
Version 7.6.1.0 Introduced on the C-Series and S-Series. E-Series original Command Usage Information Prior to using this command, to place the interface in Layer 2 mode, execute the switchport command. To remove the trunk port designation, first remove the port (using the no member interface command) from all stackable VLAN-enabled VLANs. Starting with Dell Networking OS version 7.8.1.
PAGE 1586
x - Dot1x untagged, X - Dot1x tagged G - GVRP tagged, M - Vlan-stack NUM Status Description * 1 Inactive 20 Active 100 Active Dell(conf-if-vl-20)# Example 2 Q Ports T Gi 0/42 M Gi 0/42 Dell(config)#vlan-stack protocol-type 88A8 Dell(config)#interface gigabitethernet 3/10 Dell(conf-if-gi-3/10)#no shutdown Dell(conf-if-gi-3/10)#switchport Dell(conf-if-gi-3/10)#vlan-stack access Dell(conf-if-gi-3/10)#exit Dell(config)#interface tenGigabitethernet 8/0 Dell(conf-if-te-10/0)#no shutdown Dell(conf-if-te-10/0)#po
PAGE 1587
Virtual Link Trunking (VLT) 56 Virtual link trunking (VLT) is supported on the Z-Series platform. VLT allows physical links between two chassis to appear as a single virtual link to the network core. VLT eliminates the requirement for Spanning Tree protocols by allowing link aggregation group (LAG) terminations on two separate distribution or core switches, and by supporting a loop-free topology.
PAGE 1588
ipv6 Enter the keyword ipv6 then an IPv6 address in the X:X:X:X::X format. interval seconds Enter the keyword interval to specify the time interval to send hello messages. The range is from 1 to 5 seconds. The default is 1 second. Defaults 1 second Command Modes VLT DOMAIN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1589
Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. Version 9.2(0.2) Added multicast and ndp parameters. Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.
PAGE 1590
Command Modes VLT DOMAIN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Related Commands Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.
PAGE 1591
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.
PAGE 1592
multicast peer-routing timeout Configure the time for a VLT node to retain synced multicast routes or synced multicast outgoing interface (OIF) after a VLT peer node failure. Z9000 Syntax multicast peer-routing timeout value To restore the default value, use the no multicast peer-routing timeout command. Parameters value Enter the timeout value in seconds. The range is from 1 to 1200. The default is 150. Command Modes VLT DOMAIN (conf-vlt-domain) Command History This guide is platform-specific.
PAGE 1593
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.
PAGE 1594
Version 9.2(0.2) Introduced on the Z9000, S4810, and S4820T. peer-routing-timeout Configure the delay after which peer routing is disabled when the peer is unavailable. This command is applicable for both IPV6/ IPV4. Z9000 Syntax peer-routing-timeout value To restore the default value, use the no peer-routing-timeout command. Parameters value Enter the timeout value in seconds. The range is from 1 to 65535. The default value is 0 (no timeout).
PAGE 1595
Default 32768 Command Modes VLT DOMAIN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. Version 8.3.19.
PAGE 1596
Usage Information The version shown in the show vlt brief output command displays the VLT version number which is different from the Dell Networking OS version number. VLT version numbers are begin with odd numbers such as 3 or 5.
PAGE 1597
HeartBeat Timeout: UDP Port: HeartBeat Messages Sent: HeartBeat Messages Received: 3 34998 1026 1025 show vlt counters Displays the counter information. Z9000 Syntax Parameters show vlt counters [arp| igmp-snoop | interface | mac | ndp] arp Enter the keyword arp to display the ARP counter information for the VLT. igmp-snoop Enter the keywords igmp-snoop to display the igmpsnooping counter information for the VLT.
PAGE 1598
------------------------L2 Total MAC-Address Count : IGMP MRouter Vlans count : IGMP Mcast Groups count : ARP entries count : Example (igmp-snoop) Dell# show vlt counter igmp-snoop Total IGMP VLT counters ---------------------IGMP MRouter Vlans count : 1 IGMP Mcast Groups count : 5 Example (igmp-snoop interface portchannel) Dell#show vlt counter igmp-snoop interface port-channel 2 VLT Port-ID: 2 IGMP Counter ----------------------IGMP MRouter Vlans count : 0 IGMP Mcast Groups count : 5 Dell# show vlt cou
PAGE 1599
The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.8.0 Introduced on the S4810.
PAGE 1600
show vlt mismatch Display mismatches in VLT parameters. Z9000 Syntax show vlt mismatch Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.0 Introduced on the S6000. Version 9.2(0.0) Introduced on the M I/O Aggregator.
PAGE 1601
show vlt role Displays the VLT peer status, role of the local VLT switch, VLT system MAC address and system priority, and the MAC address and priority of the local VLT device. Z-Series Syntax show vlt role Default Not configured. Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1602
show vlt statistics Displays statistics on VLT operations. Z9000 Syntax Parameters show vlt statistics [arp | domain | igmp-snoop | mac | multicast | ndp] domain Display the VLT statistics for the domain. multicast Display the VLT statistics for multicast. mac Display the VLT statistics for the MAC address. arp Display the VLT statistics for ARP. igmp-snoop Display the VLT statistics for IGMP snooping. ndp Display the VLT statistics for NDP. Default Not configured.
PAGE 1603
ICL Hello's Received: Domain Mismatch Errors: Version Mismatch Errors: Config Mismatch Errors: 910 0 0 0 VLT MAC Statistics ---------------L2 Info Pkts sent:6, L2 Mac-sync Pkts Sent:0 L2 Info Pkts Rcvd:3, L2 Mac-sync Pkts Rcvd:2 L2 Reg Request sent:1 L2 Reg Request rcvd:2 L2 Reg Response sent:1 L2 Reg Response rcvd:1 VLT Igmp-Snooping Statistics ------------------------------IGMP Info Pkts sent: 4 IGMP Info Pkts Rcvd: 1 IGMP Reg Request sent: 1 IGMP Reg Request rcvd: 2 IGMP Reg Response sent: 1 IGMP Reg R
PAGE 1604
show vlt statistics igmp-snoop Displays the informational packets and IGMP control PDUs that are exchanged between VLT peer nodes. Syntax show vlt statistics igmp-snoop Default Not configured. Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.0.2.
PAGE 1605
Command Modes VLT DOMAIN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T.
PAGE 1606
Usage Information Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.8.0 Introduced on the S4810. When you create a VLT domain on a switch, Dell Networking OS automatically assigns a unique unit ID (0 or 1) to each peer switch. The unit IDs are used for internal system operations.
PAGE 1607
Version 8.3.8.0 Introduced on the S4810. Usage Information The VLT domain ID must be the same between the two VLT devices. If the domain ID is not the same, a syslog message is generated and VLT does not launch. Related Commands show vlt — uses the show vlt brief command to display the delay-restore value. vlt-peer-lag port-channel Associate the port channel to the corresponding port channel in the VLT peer for the VLT connection to an attached device.
PAGE 1608
Because the VLT LAG interfaces are terminated on two different nodes, PVLAN configuration of VLT VLANs and VLT LAGs are symmetrical and identical on both the VLT peers. PVLANs provide Layer 2 isolation between ports within the same VLAN. A PVLAN partitions a traditional VLAN into sub-domains identified by a primary and secondary VLAN pair. With VLT being a Layer 2 redundancy mechanism, support for configuration of VLT nodes in a PVLAN enables Layer 2 security functionalities.
PAGE 1609
configured as a VLT VLAN on one peer and a non-VLT VLAN on another peer, the VLTi is added as a member of that VLAN by verifying the PVLAN parity on both the peers. In such a case, if a PVLAN is present as a VLT PVLAN on at least one of the peers, then symmetric configuration of the PVLAN is validated to cause the VLTi to be a member of that VLAN.
PAGE 1610
During the booting phase or when the ICL link attempts to come up, a system logging message is recorded if VLT PVLAN mismatches, PVLAN mode mismatches, PVLAN association mismatches, or PVLAN port mode mismatches occur. Also, you can view these discrepancies if any occur by using the show vlt mismatch command. Interoperation of VLT Nodes in a PVLAN with ARP Requests When an ARP request is received, and the following conditions are applicable, the IP stack performs certain operations.
PAGE 1611
VLT LAG Mode PVLAN Mode of VLT VLAN Peer1 Peer2 Peer1 Peer2 Promiscuo us Promiscuo us Primary Access Promiscuo us Access Promiscuo us ICL VLAN Membership Mac Synchronization Primary Yes Yes - Secondary (Community) - Secondary (Isolated) No No Secondary (Community) Secondary (Isolated) No No • • Yes Yes Primary X Primary X Primary Primary Yes Yes - Secondary (Community) - Secondary (Community) Yes Yes - Secondary (Isolated) - Secondary (Isolated) Yes Yes Promiscuo
PAGE 1612
show vlt private-vlan Display the association of private VLAN (PVLAN) with the VLT LAG. You can configure VLT peer nodes in a PVLAN on the Z9000 platforms. Syntax show vlt private-vlan Command Modes EXEC Command History Version 9.4(0.0) Introduced on the S6000 platform. Version 9.3(0.0) Introduced on the Z9000, S4810, and S4820T platforms.
PAGE 1613
VLT Proxy Gateway 57 This chapter describes the VLT Proxy Gateway feature. proxy-gateway lldp Configure the LLDP proxy gateway Z9000 Syntax proxy-gateway lldp Command Modes VLT DOMAIN Command History Usage Information Version 9.4(0.0) Introduced on the S4810, S4820T, S6000, Z9000, and MXL Switch.
PAGE 1614
proxy-gateway static Configure the VLT static proxy gateway Z9000 Syntax [no] proxy-gateway static Command Modes VLT DOMAIN Command History Version 9.4(0.0) Introduced on the S4810, S4820T, S6000, Z9000, and MXL Switch. Usage Information When proxy-gateway static configuration is made, the setting is saved in the Layer 2 application.
PAGE 1615
Command Modes Command History VLT DOMAIN PROXY GW STATIC Version 9.4(0.0) Introduced on the S4810, S4820T, S6000, Z9000, and MXL Switch. Usage Information You can configure the remote MAC address of the VLT peer to be associated with the static VLT proxy gateway and exclude a VLAN or a range of VLANs from proxy routing. This parameter is for a static VLT proxy gateway configuration.
PAGE 1616
Example Dell(conf)#vlt-domain 1 Dell(conf-vlt-domain)#proxy-gateway lldp Dell(conf-vlt-domain-proxy-gw-lldp)#peer-domain-link portchannel 20 exclude-vlan 3 proxy-gateway peer-timeout Configure the proxy-gateway VLT peer timeout value. Z9000 Syntax Parameters Command Modes Command History [no] peer-timeout value value Enter the timeout value in seconds. The range is from 1 to 65535. The default is infinity. VLT DOMAIN PROXY GW LLDP Version 9.4(0.
PAGE 1617
Usage Information In a square VLT topology with only one link connecting remote peers, if you configure this command, any node has to send its VLT peer’s MAC address along with its own MAC address to the remote VLT domain. By default, a node will send only its own MAC address to the remote VLT domain. This parameter is applicable for an LLDP proxy gateway configuration. Example Dell(conf-vlt-domain-proxy-gw-lldp)# vlt-peer-mac transmit show vlt-proxy-gateway Display the VLT proxy gateway configuration.
PAGE 1618
Example Dell(conf)#do sh vlt proxy-gateway info static Mac Address Exclude Vlan ---------------------00:01:e8:8b:1c:c0 Dell#show vlt proxy-gateway info LagId Mac Address --------------Po 55 00:01:e8:8a:e8:f7 learnt via port-channel 55 Po 55 00:01:e8:8b:1c:c0 1618 lldp Exclude Vlan -----------3,7-8 << Macs 3,7-8 VLT Proxy Gateway
PAGE 1619
Virtual Routing and Forwarding (VRF) 58 Virtual Routing and Forwarding (VRF) allows multiple instances of a routing table to co-exist on the same router at the same time. Virtual Routing and Forwarding (VRF) is supported on the S-Series platforms. ip vrf Creates a customer VRF. Z-Series Syntax ip vrf {vrf-name | management} [vrf_id] To delete a customer VRF, use the no ip vrf {vrf-name | management} [vrf_id] command. Parameters vrf-name Enter the name of the VRF that you want to create.
PAGE 1620
description Enables you to specify a descriptive name for a customer VRF. Z-Series Syntax description string To delete the descriptive name for a customer VRF, use the no description string command. Parameters string Enter a descriptive name for the VRF. Defaults None. Command Modes VRF MODE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1621
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.4. (0.0) Introduced on the S-Series and Z-Series. Version 8.2.1.0 Introduced on the E-Series. Version Introduced on the S4810. Version Introduced on the S-Series. Version Introduced on the C-Series.
PAGE 1622
interface management Associates a management port with a management VRF. Z-Series Syntax interface management To delete the association between a management port and a management VRF, use the no interface management command. Defaults None. Command Modes VRF MODE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1623
Example Version 9.4. (0.0) Introduced on the S-Series and Z-Series. Version 8.2.1.0 Introduced on the E-Series.
PAGE 1624
Version 9.4. (0.0) Introduced on the S-Series Z-Series. Version 8.2.1.0 Introduced on the E-Series. Usage Information Use this command to display configuration information corresponding to either a specific VRF or all the VRFs in the system.
PAGE 1625
Virtual Router Redundancy Protocol (VRRP) 59 Virtual router redundancy protocol (VRRP) is supported by the Dell Networking operating system on the Z-Series platform. IPv4 VRRP Commands The following are IPv4 VRRP commands. advertise-interval Set the time interval between VRRP advertisements. Z-Series Syntax advertise-interval seconds To return to the default settings, use the no advertise-interval command. Parameters seconds Enter a number of seconds. The range is from 1 to 255.
PAGE 1626
Usage Information Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. Dell Networking recommends keeping the default setting for this command. If you do change the time interval between VRRP advertisements on one router, change it on all routers. authentication-type Enable authentication of VRRP data exchanges.
PAGE 1627
Usage Information Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. The given password is encrypted by the system and the show config displays an encrypted text string for any of the encrypted typed used. clear counters vrrp Clear the counters maintained on VRRP operations. Z-Series Syntax Parameters clear counters vrrp [vrrp-id] [ipv6] vrrp-id (OPTIONAL) Enter the number of the VRRP group ID. The range is from 1 to 255.
PAGE 1628
To disable debugging, use the no debug vrrp interface [vrrp-id] {all | bfd | database | interface | ipv6 | packets | state | timer} command. Parameters interface Enter the following keywords and slot/port or number information • For Port Channel interface types, enter the keywords port-channel then the number. The range is from 1 to 128. • For a 1-Gigabit Ethernet interface, enter the keyword gigabitethernet followed by the slot/port information.
PAGE 1629
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. If no options are specified, debug is active on all interfaces and all VRRP groups. description Configure a short text string describing the VRRP group.
PAGE 1630
disable Disable a VRRP group. Z-Series Syntax disable To re-enable a disabled VRRP group, use the no disable command. Command Modes VRRP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.
PAGE 1631
Defaults zero (0) seconds Command Modes VRRP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.
PAGE 1632
Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. priority Specify a VRRP priority value for the VRRP group. The VRRP protocol uses this value during the MASTER election process. Z-Series Syntax priority priority To return to the default value, use the no priority command. Parameters priority Enter a number as the priority.
PAGE 1633
Usage Information To guarantee that a VRRP group becomes MASTER, configure the VRRP group’s virtual address with same IP address as the interface’s primary IP address and change the priority of the VRRP group to 255. If you set the priority command to 255 and the virtual-address is not equal to the interface’s primary IP address, an error message appears. show config View the non-default VRRP configuration.
PAGE 1634
show vrrp View the VRRP groups that are active. If no VRRP groups are active, the FTOS returns No Active VRRP group. Z9000 Syntax Parameters show vrrp [vrrp-id] [interface] [brief][ipv6] vrrp-id (OPTIONAL) Enter the Virtual Router Identifier for the VRRP group to view only that group. The range is from 1 to 255. interface (OPTIONAL) Enter the following keywords and slot/port or number information: • For Port Channel interface types, enter the keywords port-channel then the number.
PAGE 1635
pre-Version 6.2.1.1 Usage Information Introduced on the E-Series. The following describes the show vrrp brief command shown in the following example. Item Description Interface Lists the interface type, slot and port on which the VRRP group is configured. Grp Displays the VRRP group ID. Pri Displays the priority value assigned to the interface.
PAGE 1636
Item Description GigabitEthernet 12/3... Displays the Interface, the VRRP group ID, and the network address. If the interface is not sending VRRP packets, 0.0.0.0 appears as the network address. State: master... Displays the interface’s state: • Na/If (not available) • master (MASTER virtual router) • backup (BACKUP virtual router) the interface’s priority and the IP address of the MASTER. Hold Down:... Adv rcvd:...
PAGE 1637
Virtual MAC address: 00:00:5e:00:01:01 Virtual IP address: 10.1.1.252 Authentication: (none) Tracking states for 1 interfaces: Up GigabitEthernet 12/17 priority-cost 10 -----------------GigabitEthernet 12/4, VRID: 2, Net: 10.1.2.253 State: Master, Priority: 110, Master: 10.1.2.253 (local) Hold Down: 10 sec, Preempt: TRUE, AdvInt: 1 sec Adv rcvd: 0, Adv sent: 1862, Gratuitous ARP sent: 0 Virtual MAC address: 00:00:5e:00:01:02 Virtual IP address: 10.1.2.
PAGE 1638
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced support for telnetting to the VRRP group IP address assigned using this command. pre-Version 6.2.1.1 Introduced on the E-Series. The VRRP group only becomes active and sends VRRP packets when a virtual IP address is configured.
PAGE 1639
Usage Information Related Command Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.8.0 Introduced on the S4810. This command applies to a single interface. When used with the vrrp delay reload CLI, the later timer rules the VRRP enabling. For example, if vrrp delay reload is 600 and the vrrp delay minimum is 300: • When the system reloads, VRRP waits 600 seconds (10 minutes) to bring up VRRP on all interfaces that are up and configured for VRRP.
PAGE 1640
For example, if vrrp delay reload is 600 and the vrrp delay minimum is 300: • When the system reloads, VRRP waits 600 seconds (10 minutes) to bring up VRRP on all interfaces that are up and configured for VRRP. • When an interface comes up, whether as part of a system reload or an interface reload, the system waits 300 seconds (5 minutes) to bring up VRRP on that interface. Save the configuration and reload the system for the delay timers to take effect.
PAGE 1641
Related Command virtual-address — assigns up to 12 virtual IP addresses per VRRP group. IPv6 VRRP Commands The following are IPv6 VRRP commands. • clear counters vrrp ipv6 • debug vrrp ipv6 • show vrrp ipv6 • vrrp-ipv6-group The following commands apply to IPv4 and IPv6: • advertise-interval • description • disable • hold-time • preempt • priority • show config • virtual-address clear counters vrrp ipv6 Clear the counters recorded for IPv6 VRRP groups.
PAGE 1642
Version 8.3.10.0 Introduced on the S4810. Version 8.4.1.0 Introduced on E-Series ExaScale, C-Series, and S-Series. Support was added for IPv6 VRRP groups in non-default VRF instances. Version 8.3.2.0 Introduced on the E-Series TeraScale. debug vrrp ipv6 Allows you to enable debugging of VRRP.
PAGE 1643
The following is a list of the Dell Networking OS version history for this command. Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.10.0 Introduced on the S4810. Version 8.4.1.0 Introduced on E-Series ExaScale, C-Series, and S-Series. Support was added for IPv6 VRRP groups in non-default VRF instances. Version 8.3.2.0 Introduced on the E-Series TeraScale. If no options are specified, debug is active on all interfaces and all VRRP groups.
PAGE 1644
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.10.0 Introduced on the S4810. Version 8.3.2.0 Introduced on the E-Series TeraScale. The following describes the show vrrp ipv6 command shown in the following example. Line Beginning with Description GigabitEthernet... Displays the Interface, the VRRP group ID, and the network address. If the interface is no sending VRRP packets, 0.0.0.0 appears as the network address.
PAGE 1645
Line Beginning with Example Description • UP or DOWN state of the tracked interface or object (Up or Dn). • Interface type and slot/port or object number, description, and time since the last change in the state of the tracked object. • Cost to be subtracted from the VRRP group priority if the state of the tracked interface/object goes DOWN.
PAGE 1646
Usage Information Version 8.3.7.0 Introduced on the S4810. Version 8.3.2.0 Introduced on the E-Series TeraScale. The VRRP group only becomes active and sends VRRP packets when a link-local virtual IP address is configured. When you delete the virtual address, the VRRP group stops sending VRRP packets. • When VRF microcode is not loaded in CAM, the VRID for a VRRP group is the same as the VRID number configured with the vrrp-group or vrrp-ipv6group command.
PAGE 1647
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. Dell Networking recommends keeping the default setting for this command. If you do change the time interval between VRRP advertisements on one router, change it on all routers.
PAGE 1648
pre-Version 6.2.1.1 Introduced on the E-Series. disable Disable a VRRP group. Z-Series Syntax disable To re-enable a disabled VRRP group, use the no disable command. Command Modes VRRP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.
PAGE 1649
hold-time Specify a delay (in seconds) before a switch becomes the MASTER virtual router. By delaying the initialization of the VRRP MASTER, the new switch can stabilize its routing tables. Z-Series Syntax hold-time seconds To return to the default value, use the no hold-time command. Parameters seconds Enter a number of seconds. The range is from 0 to 65535. The default is zero (0) seconds. Defaults zero (0) seconds Command Modes VRRP Command History This guide is platform-specific.
PAGE 1650
preempt To preempt or become the MASTER router, permit a BACKUP router with a higher priority value. Z-Series Syntax preempt To prohibit preemption, use the no preempt command. Defaults Enabled (that is, a BACKUP router can preempt the MASTER router). Command Modes VRRP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1651
Defaults 100 Command Modes VRRP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.16.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.
PAGE 1652
Example Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. Dell(conf-if-vrid-4)#show con vrrp-group 4 virtual-address 119.192.182.124 ! virtual-address Configure up to 12 IP addresses of virtual routers in the VRRP group.
PAGE 1653
Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced support for telnetting to the VRRP group IP address assigned using this command. pre-Version 6.2.1.1 Introduced on the E-Series.