Virtual Edge Platform (VEP) 1405 Series Technology Guide Abstract This document provides an overview of the systems offered as part of the VEP1405 series of systems. Dell Networking Solutions July 2021 Rev.
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2021 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
Contents Chapter 1: Product description......................................................................................................4 Chapter 2: Product positioning and key marketing messages........................................................ 7 Product overview.................................................................................................................................................................7 Product specifications....................................................
1 Product description The Dell EMC Virtual Edge Platform (VEP) 1405 is a next-generation access platform family. The products within the VEP1405 line are built for edge compute, such as uCPE, SD-WAN, and ROBO. The VEP1405 product line consists of the five models that are described in the table below. The VEP1405 is the second product that is launched in the VEP family. The VEP1405 line is a cost-optimized platform with a lower performance level than the previously released VEP4600 platform.
Table 1. Dell EMC Virtual Edge Platform (VEP) 1405 model descriptions (continued) Model SKU CPU Description ● ● ● ● ● ● ● ● 2x 2 Wi-Fi 6x 1 GB Copper RJ45 2x 10 GB SFP+ ADVA software installed Trusted Platform Module (TPM) 2.0 - World-wide except China 2x USB 3.0 Low-energy Bluetooth (BLE) Two fans VEP1445N 210-BBZZ 8-core ● ● ● ● ● ● ● ● ● 16 GB DDR4 16 GB eMMC 240 GB SSD 6x 1 GB Copper RJ45 2x 10 GB SFP+ Versa software installed Trusted Platform Module (TPM) 2.
Wireless bands NOTE: Only certain VEP1405 series models have Wi-Fi capabilities. See the Dell EMC Virtual Edge Platform (VEP) 1405 model descriptions table above for a complete list of systems that include the Wi-Fi functionality. The wireless bands that are supported for Wi-Fi are as follows: This module has the Qualcomm Atheros Peregrine chipset QCA9882-BR4B that is often used in high-performance Wi-Fi access points. ● Wi-Fi ○ 2.
2 Product positioning and key marketing messages The VEP family targets two main use cases: ● Software-defined wide area network (SD-WAN) appliance market ● Universal CPE (uCPE) market The uCPE market is a superset of the SD-WAN use case that unites multiple software functions onto a single hardware device through virtualization. uCPE and SD-WAN are estimated to grow at ~60% CAGR and with a projected TAM of $8.05 billion by 2021.
Product specifications Table 2. Key features Feature Overview Processor Intel Denverton-NS (Atom processor, C3000 family) Intel CPU SKU C3558 (4-core), C3758 (8-core), C3958 (16-core) Chipset North and south bridge that is built into the CPU/SOC Memory DDR4 with ECC Out of band management Micro-USB console Mounting options Desktop, wall mount, or rack mount (1.5 RU, dual unit tray) Dimension 208 mm (8.18 in) x 52 mm (2.04 in) x 200 mm (7.87 in) (W x H x D) Weight 1.3 kg to 1.
Third-party software The eco-system in which the VEP1405 series of systems participates, includes Versa, ADVA, OneAccess, ESXi, and RAD active, with the inclusion of other partners later. Except for ESXI, which is the OEM software, all eco-system partners are on EI, which means that licenses are a sell through and that Dell does not offer support for the software. RFP questions that are related to the software are handled by the software vendor directly.
3 System overview Front and rear view Front view Figure 1. Front system view - VEP1425 model 1. Security lock port 2. USB port 3. System status indicator LED NOTE: The VEP1405 models do not have external antennas. Wi-Fi antennas are housed fully within the chassis (in select models only).
Rear view Figure 2. Rear system view - VEP1405 series model 1. 2. 3. 4. 5. 6. Micro USB port Reset button LED status lights for SFP+ ports SFP+ ports Ethernet ports and LED status lights Power connection port NOTE: To prevent the VEP1405 series system console port from being accessed in a nonsecure location, the system ships from the factory with a plate covering the micro USB port. To uncover the port, use a #0 (2.
Table 5. Architecture overview (continued) Component Description ○ 128 GB: 277 Terabytes Written (TBW) ○ 256 GB: 305 Terabytes Written (TBW) The VEP1445 system is available with 960GB SSD, and the VEP1485 system is available with 2TB SSD. The specifications for these drives are as follows: ● Compliance: SATA Gen3 - 6 Gbit/s (Gen2 - 3 Gbit/s and Gen1 - 1.5 Gbit/s backward compatible) ● Command Sets: Supports ATA/ATAPI-8 and ACS-2 ● Performance: ○ Burst Transfer Rate: Up to 600 MBytes/s in SATA Gen3 - 6.
Table 5. Architecture overview (continued) Component Description NOTE: To download the console port driver, see https://www.silabs.com/products/developmenttools/software/usb-to-uart-bridge-vcp-drivers Power supply: The power supply connector is on the same side as the I/O. The VEP1405 ships with one external AC/DC power supply Wi-Fi (select models only): ● 802.11 b/g/n/ac, 2x2 MIMO ● The VEP1405 models do not have external antennas. Wi-Fi antennas are housed fully within the chassis.
Acoustic noise and vibration report ISO 7779 A-weighted sound pressure level: 20 dBA at 73.4oF (23oC). Table 7. Acoustic noise and vibration information Acoustic noise (db) Non-Operational Random Vibration 10~500 HZ(G2/ HZ=0.13-0.0018), 1.88 Grms RHS 15 Minutes for each side (See information below this table) Operation Random Vibration 5~350 HZ(G2/ HZ=0.0002-0.0002), 0.26 Grms, RHS 15 Minutes for each side Shock non-op. 2 ms half-Sine Wave 71 g, 1 shock for each side Shock op 2.
Electrical, power, and cooling Power supplies The VEP1405 supports one external AC/DC power supply with secure locking thread. Table 10. Power specifications Parameter Specification Power input AC: 100 VAC–240 VAC, 50/60 Hz Max current draw per system - AC ● 100 VAC: 2.0A ● 240 VAC: 1.0A Power output 12 V DC, 5.
LED behavior Status LED behavior Table 13. Status LED behavior Class Behavior Status LED (Red/Green/Blue) ● Depends on partner operating system Port LED behavior Table 14.
Figure 3. VEP1405 series desktop placement Wall mount installation The VEP1405 series includes the hardware that is required for wall mount installation. Using a torque screwdriver, affix the wall mount brackets to the VEP1405 series using the four M3 screws included. NOTE: When driving the screws into the bracket and VEP1405 series unit, verify that 5 lb-in is the achieved torque setting.
Figure 5. VEP1405 series wall mount, installation anchor, and screw dimensions NOTE: Before mounting the VEP1405 series to the wall, verify that the wall surface is strong enough to support a firm installation of the unit and can withstand the weight of the unit, power cable, and network cabling. Using the measurements provided in the following diagram, use the measurement in the red box to mark the distance between the two installation points: Figure 6.
Figure 7. VEP1405 series wall mount bracket installation - cross-shaped cutout Rack-mounted installation As an option, the VEP1405 series can be mounted to a dual rack mount tray. Purchased separately, you can install the VEP1405 series to the dual rack mount tray using a torque screwdriver and the eight M3 screws included. NOTE: When driving the screws into the bracket and VEP1405 series unit, verify that 5 lb-in is the achieved torque setting.
Rack mount kit Table 15. Rack mount kit SKU SKU Description 770-BCZE Rack mount kit Regulatory Compliance Safety ● UL/CSA 60950 ‐ 1, Second Edition ● EN 60950 ‐ 1, Second Edition ● EC 60950 ‐ 1, Second Edition Including all National Deviations and Group Differences ● IEC 62368-1 ● EN 60825 ‐ 1 Safety of Laser Products Part 1: Equipment Classification Requirements and Users Guide ● EN 60825 ‐2 Safety of Laser Products Part 2: Safety of Optical Fiber Communication Systems FDA Regulation 21 CFR 1040.
● ● ● ● ● Enterprise Enterprise Enterprise Enterprise Enterprise Operational Half-Sine Shock – SV0107 Non-Operational Random Vibration – SV0102 Non-Operational Half-Sine Shock – SV0106 Non-Operational Square Wave Shock – SV0108 Rack and Stack Vibration Test – SV0114 Country of origin Made in Taiwan.
4 Sales information Products being replaced Not applicable.
Table 17. Services offerings (continued) Category Description Technical support A collaborative support agreement is performed for all software partners. Per the agreement, when a customer calls Dell for support, a hardware validation check is performed. If the validation determines that the issue is software related, a warm transfer to the software vendor is initiated.
A MTBF disclaimer Disclaimer THE DELL INFORMATION OR THIRD PARTY VENDOR DATA CONTAINED HEREIN IS PROVIDED STRICTLY "AS IS", WITHOUT WARRANTY, AND DELL EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY, TITLE OR FITNESS FOR A PARTICULAR PURPOSE REGARDING SAID INFORMATION OR DATA, EVEN IN THE EVENT DELL HAS KNOWLEDGE OF DEFICIENCIES IN SAID INFORMATION OR DATA.
Supplier data is provided as is to Dell, and Dell generally does not verify the accuracy of supplier data. Subsystem MTBF data release policy Dell does not release MTBF data below the system level. The reasons for this policy are: ● Dell considers internally designed subsystem MTBF data to be confidential intellectual property. ● Dell obtains supplier subsystem MTBF data under NDA and is prohibited from releasing it.