Dell Embedded Box PC 5000 Service Manual Regulativni model: N01PC Regulativni tip: N01PC001
Opombe, svarila in opozorila OPOMBA OPOMBA označuje pomembne informacije, ki vam pomagajo bolje izkoristiti računalnik. POZOR SVARILO oznacuje monost pokodb strojne opreme ali izgube podatkov in svetuje, kako se izogniti teavi. Opozorilo OPOZORILO označuje možnost poškodb lastnine, osebnih poškodb ali smrti. Copyright © 2017 družba Dell Inc. ali njene hčerinske družbe. Vse pravice pridržane. Dell, EMC in druge blagovne znamke so blagovne znamke družbe Dell Inc. ali njenih hčerinskih družb.
Kazalo 1 Before working inside your Embedded Box PC.................................................................................9 Before you begin....................................................................................................................................................................9 Safety instructions.................................................................................................................................................................
12 Removing the interposer board.................................................................................................. 24 Prerequisites.........................................................................................................................................................................24 Procedure.............................................................................................................................................................................
Procedure............................................................................................................................................................................. 43 24 Replacing the WWAN-antenna connectors..................................................................................45 Procedure.............................................................................................................................................................................
Procedure............................................................................................................................................................................. 63 36 Replacing the intrusion switch...................................................................................................64 Procedure.............................................................................................................................................................................
Procedure.............................................................................................................................................................................80 48 Replacing the top cover............................................................................................................ 82 Procedure.............................................................................................................................................................................
Peripherals............................................................................................................................................................................99 WLAN/WWAN...................................................................................................................................................................100 Zigbee................................................................................................................................................
1 Before working inside your Embedded Box PC OPOMBA The images in this document may differ from your Embedded Box PC depending on the configuration you ordered. Teme: • • • • Before you begin Safety instructions Recommended tools Screw list Before you begin 1. Save and close all open files and exit all open applications. 2. Shut down the Embedded Box PC. The shut-down instruction varies depending on the operating system installed on the Embedded Box PC.
POZOR Press and eject any installed card from the media-card reader. Recommended tools The procedures in this document may require the following tools: • • • • • • Philips screwdriver Flat-head screwdriver Plastic scribe Hex screwdriver 8 mm open wrench 10 mm open wrench Screw list The following table provides the list of screws used for securing different components to the Embedded Box PC.
Component Secured to Screw type Quantity Hard-drive cage Back cover M3x5 4 Top hard drive/solid-state drive Hard-drive cage STDF(L5.1), M3x3 4 Bottom hard drive/solid-state drive Hard-drive cage STDF(L5.
2 After working inside your Embedded Box PC POZOR Leaving stray or loose screws inside your Embedded Box PC may severely damage your Embedded Box PC. 1. Replace all screws and ensure that no stray screws remain inside the Embedded Box PC. 2. Connect any external devices, peripherals, or cables you removed before working on the Embedded Box PC. 3. Connect your Embedded Box PC and all attached devices to their electrical outlets. 4. Turn on the Embedded Box PC.
3 Technical overview OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • System-board components System-board components 1. 3. 5. 7. 9. 11. 13. 15.
4 Removing the back cover OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • Procedure Procedure 1.
1. back cover 3. routing guide 5. SATA-power cable 2. hard drive/Solid-state drive assembly 4. SATA-data cable 5. Close the back cover partially and push the back cover forward to release it from the tabs on the chassis. 6. Lift the back cover off the chassis. a. back cover b. chassis 7. Remove the Removing the hard-drive cage.
5 Replacing the back cover OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • Procedure Procedure 1. Replace the hard-drive cage. 2.
6 Removing the hard-drive cage OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. POZOR Hard drives/solid-state drives are fragile.
7 Replacing the hard-drive cage OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. POZOR Hard drives/solid-state drives are fragile.
8 Removing the drives from the hard-drive cage OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. POZOR Hard drives/solid-state drives are fragile.
1. back cover 3. drive cage 20 Removing the drives from the hard-drive cage 2. STDF (L5.1), M3x3 screws(4) 4.
9 Replacing the drives in to the hard-drive cage OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. POZOR Hard drives/solid-state drives are fragile.
10 Removing the solid-state drive from bracket OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. POZOR Solid-state drives are fragile.
11 Replacing the solid-state drive in to bracket OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. POZOR Solid-state drives are fragile.
12 Removing the interposer board OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Prerequisites Procedure Prerequisites 1.
13 Replacing the interposer board OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Procedure Post-requisites Procedure 1.
14 Installing a PCI/PCIe card OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. POZOR PCI/PCIe cards are fragile. Exercise care when handling the cards.
1. M3x5 countersunk screw 3. filler plate 2. PCI/PCIe filler-plate bracket 4. chassis 5. Install the PCIe or PCI cards in their respective slots on the riser board. a. riser card b. PCIe card slot c. PCIe card 6. Replace the filler plate for an empty card slot. 7. Replace the filler-plate bracket on the chassis. 8. Replace the screw that secures the bracket to the chassis.
1. filler bracket 3. chassis 2. bracket 4. M3x5 countersunk screw 9. Replace the screws that secure the PCIe card and the filler plate to the chassis. a. chassis b. filler plate c. M3x5 countersunk screws (2) Post-requisites Follow step 2 to step 8 in “Replacing the back cover”.
15 Removing the PCI/PCIe card OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance.
1. M3x5 countersunk screw 3. filler plate 2. bracket 4. chassis 5. Release the PCI/PCIe card from the PCI/PCIe card slot on the riser card and lift it off the chassis. 1. PCIe card 3. riser card 30 Removing the PCI/PCIe card 2. PCIe card-slot 4.
16 Replacing the PCIe card OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Procedure Post-requisites Procedure 1.
1. filler plate 3. chassis 2. fillet-plate bracket 4. M3x5 countersunk screw 5. Replace the screws that secure the PCI/PCIe card and the filler plate to the chassis. a. chassis b. filler plate c. M3x5 countersunk screws (2) Post-requisites Follow step 2 to step 8 in “Replacing the back cover”.
17 Removing the memory module OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Prerequisites Procedure Prerequisites 1.
c.
18 Replacing the memory module OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Procedure Post-requisites Procedure 1.
Post-requisites 1. Replace the PCI/PCIe card (if necessary). 2. Follow step 2 to step 8 in “Replacing the back cover”.
19 Removing the WLAN-antenna connectors OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Prerequisites Procedure Prerequisites 1.
a. antenna cables b. routing guide c.
20 Replacing the WLAN-antenna connectors OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Procedure Post-requisites Procedure 1.
21 Removing the WLAN card OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Prerequisites Procedure Prerequisites 1.
22 Replacing the WLAN card OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance.
1. tab 3. WLAN card 5. M2x3 screws (2) Post-requisites 1. Replace the PCI/PCIe card (if necessary). 2. Follow step 2 to step 8 in “Replacing the back cover”. 42 Replacing the WLAN card 2. notch 4. WLAN-card bracket 6.
23 Removing the WWAN-antenna connectors OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Prerequisites Procedure Prerequisites 1.
a. WWAN-antenna cables (2) b. routing guide c.
24 Replacing the WWAN-antenna connectors OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Procedure Post-requisites Procedure 1.
25 Removing the WWAN card OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Prerequisites Procedure Prerequisites 1.
3. mPCIE1 slot 4.
26 Replacing the WWAN card OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance.
1. tab 3. M2x3 screws (2) 5. WWAN-antenna cables (2) 2. notch 4. WWAN card Post-requisites 1. Replace the PCI/PCIe card (if necessary). 2. Follow step 2 to step 8 in “Replacing the back cover”.
27 Removing the SIM card OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Prerequisites Procedure Prerequisites 1.
28 Replacing the SIM card OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Procedure Post-requisites Procedure 1.
2. Follow step 2 to step 8 in “Replacing the back cover”.
29 Removing the CANbus cable OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Prerequisites Procedure Prerequisites 1.
3. routing guides 54 Removing the CANbus cable 4.
30 Replacing the CANbus cable OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Procedure Post-requisites Procedure 1.
31 Removing the CANbus card OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Prerequisites Procedure Prerequisites 1.
1. CANbus card 3. mPCIE1 slot 5. M2x3 screws (2) 2. CANbus cable 4.
32 Replacing the CANbus card OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Procedure Post-requisites Procedure 1.
Post-requisites 1. Replace the PCI/PCIe card (if necessary). 2. Follow step 2 to step 8 in “Replacing the back cover”.
33 Removing the coin-cell battery OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance.
c.
34 Replacing the coin-cell battery OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance.
35 Removing the intrusion switch OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Prerequisites Procedure Prerequisites 1.
36 Replacing the intrusion switch OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Procedure Post-requisites Procedure 1.
37 Removing the serial ports OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Prerequisites Procedure Prerequisites 1.
a. chassis b. serial-port connector c.
38 Replacing the serial ports OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Procedure Post-requisites Procedure 1.
39 Removing the bottom cover OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Prerequisites Procedure Prerequisites 1.
40 Replacing the bottom cover OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Procedure Post-requisites Procedure 1.
41 Removing the riser card OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Prerequisites Procedure Prerequisites 1.
a. riser-card bracket b. screws (2) c.
42 Replacing the riser card OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance.
Skica 1. DIP switch settings with two PCIe(x8) cards 1. DIP switch 2.
Skica 2. DIP switch settings with other riser cards 1. DIP switch 2. CPU board 1. Align the screw holes on the bracket with the screw holes on the riser card. 2. Replace the screws that secure the bracket with the riser card. 3. Insert the riser-card assembly in the riser-card slot. 4. Replace the screws that secure the riser-card assembly to the chassis. Post-requisites 1. Replace the PCI/PCIe card (if necessary). 2. Follow step 2 to step 8 in “Replacing the back cover”.
43 Removing the heat sink OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Prerequisites Procedure Prerequisites 1.
44 Replacing the heat sink OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Procedure Post-requisites Procedure 1.
45 Removing the power connectors OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Prerequisites Procedure Prerequisites 1.
1. chassis 3. routing guide 5. power cable 2. barrel connector 4. M2.5x2 screw 6. grounding cable 6. Remove the screws that secure the power connector to the chassis. 7. Route the power cables along with the barrel connector through the slot on the chassis and remove it from the chassis. a. chassis b. power connector c. M2.
46 Replacing the power connectors OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Procedure Post-requisites Procedure 1.
47 Removing the top cover OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Prerequisites Procedure Prerequisites 1.
4. Remove the top cover off the chassis. a. M3x5 countersunk screws (7) b. top cover c. chassis 5. Remove the power switch.
48 Replacing the top cover OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Procedure Post-requisites Procedure 1. Replace the power switch. 2.
49 Removing the power switch OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Prerequisites Procedure Prerequisites 1.
50 Replacing the power switch OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Procedure Post-requisites Procedure 1.
51 Removing the CPU board OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Prerequisites Procedure Prerequisites 1.
52 Replacing the CPU board OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance.
53 Removing the system board OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. OPOMBA Your Embedded Box PC’s Service Tag is stored in the system board.
1. serial-port cable 3. SATA power-cable (2) 2. SATA data-cable (2) 4. system board 2. Remove the screws that secure the system board to the chassis. 1. chassis 3. STDF(L8) HEX, M3x4 screws (5) 5. M3x5 screws (8) 3. Lift the system board off the chassis. 88 Removing the system board 2. system board 4.
a. chassis b.
54 Replacing the system board OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. OPOMBA Your Embedded Box PC’s Service Tag is stored in the system board.
3. Navigate to the Main tab and enter the Service Tag in the Service Tag Input field.
55 BIOS setup program Entering BIOS setup program Before turning on the Embedded Box PC, connect the keyboard, mouse, and monitor to the Embedded Box PC, or connect the Embedded Box PC through the KVM session or use Dell Wyse Cloud Client Manager (CCM) or Dell Command | Monitor (DCM) to update the BIOS configuration. 1. Turn on (or restart) the Embedded Box PC. 2. During POST, when the DELL logo is displayed, watch for the F2 prompt to appear, and then press F2 immediately.
a. jumper plug 8. Follow step 2 to step 9 in “Replacing the back cover”. Clearing CMOS settings 1. Follow step 1 to step 6 in “Removing the back cover”. 2. Locate the CMOS reset jumper (CMOS) on the system board. See “System-board components”. 3. Move the jumper plug from pins 1 and 2 to 2 and 3. 4. Follow step 2 to step 9 in “Replacing the back cover”. 5. Turn on the Embedded Box PC, and wait until the message stating that the CMOS has been cleared appears. 6. Shut down the Embedded Box PC. 7.
a. jumper plug 8. Follow step 2 to step 8 in “Replacing the back cover”.
56 Removing the Dell logo board OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Prerequisites Procedure Prerequisites 1.
a. left chassis b. M3x6 screws (7) c. front chassis 2. Remove the screws that secure the Dell logo board to the front chassis. a. M3x5 screws (3) b. front chassis 3. Remove the Dell logo board from the front chassis.
a. Dell logo board b.
57 Replacing the Dell logo board OPOMBA Before working inside your Embedded Box PC, read the safety information that shipped with your Embedded Box PC and follow the steps in Before working inside your Embedded Box PC. After working inside your Embedded Box PC, follow the steps in After working inside your Embedded Box PC. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Teme: • • Procedure Post-requisites Procedure 1.
58 Technology and components Teme: • • • • • • • Power Processor Mechanical Peripherals WLAN/WWAN Zigbee CANbus Power The Dell Embedded Box PC is shipped with the 12-26V DC power adapter. Processor The Dell Embedded Box PC is shipped with Intel Celeron G3900E, Intel Core i3-6100E, Intel Core i5-6440EQ, and Intel Core i7-6820EQ processor. Mechanical The Embedded Box PC is optimized for fanless design, and easy wall/panel and DIN Rail Mount use. It provides easy access to connectors and switches.
• • • • Mobile Broadband card Mobile WLAN card CANbus card Power adapter WLAN/WWAN The following WLAN and WWAN cards are optionally offered in the Embedded Box PC: • • Dual-band 802.11b/g/n/ac+Bluetooth 4.1 LE Dell Wireless DW5580 HSPA+ Zigbee The Zigbee USB module is a wireless mesh module for Dell Embedded Box PC. CANbus The CANBus daughter card is an optional accessory for Embedded Box PC.
