Installation Instructions

ManualsBrandsDELL ManualsElectronicsMC Carrier Card

WIFI, LTE Card installation

Install the Virtual Edge Platform (VEP) WIFI carrier cards with the replacement kit supplied. To

complete this installation, use the included standoffs, also known as spacers, and screws

found in the replacement kit.

CAUTION: To avoid electrostatic discharge (ESD) damage, wear grounding wrist straps

when handling this equipment.

WARNING: Customers are not to attempt installing Virtual Edge Platform (VEP) 4600

expansion cards. A Dell EMC Certified technician must perform this installation.

The VEP4600 WIFI carrier card is required to install the validated WIFI/LTE card into the

VEP4600 for customers who desire additional ports for their VEP4600. The VEP4600 WIFI

carrier card and the WIFI/LTE card will all ship separately from the VEP4600, so before

beginning the installation, ensure you have all required devices:

• VEP4600

• VEP4600 WIFI carrier card kit, including bag with standoffs and two screws

• WIFI/LTE card kit

NOTE: The VEP4600 WIFI carrier card is not attached to the WIFI/LTE card when it ships

to the customer.

1 Remove the VEP4600 top cover 10 screws and retain the screws from the top cover.

Summary of content (19 pages)

PAGE 1
WIFI, LTE Card installation Install the Virtual Edge Platform (VEP) WIFI carrier cards with the replacement kit supplied. To complete this installation, use the included standoffs, also known as spacers, and screws found in the replacement kit. CAUTION: To avoid electrostatic discharge (ESD) damage, wear grounding wrist straps when handling this equipment. WARNING: Customers are not to attempt installing Virtual Edge Platform (VEP) 4600 expansion cards.
PAGE 2
Figure 40. Top cover removal 2 Remove and retain the two screws from the bottom of the chassis. NOTE: Must retain top and bottom screws.
PAGE 3
Figure 41. Blank front panel bottom screws 3 Decide which VEP4600 WIFI carrier card slot MC1 or MC2, or both, to install the WIFI carrier card card(s) per customer order. 4 Pull-up the blank panel from either location MC1 or MC2(s) VEP4600 WIFI carrier card slot. NOTE: Do not leave an VEP4600 WIFI carrier card slot empty. Either a blank panel or installed VEP4600 WIFI carrier card must be installed. The following steps explain how-to install a VEP4600 WIFI carrier card in slot MC1. Figure 42.
PAGE 4
Figure 43. Remove guide pin 6 Remove the two standoffs labeled Change standoff in the MC1 VEP4600 WIFI carrier card slot.
PAGE 5
Figure 44. Change standoffs 7 Replace the removed standoffs in MC1 VEP4600 WIFI carrier card slot with the shorter standoffs from the VEP4600 WIFI carrier card kit like MC2 in the following figure. 8 Be sure you have one guide pin and two shorter standoffs as shown in slot MC2. Figure 45.
PAGE 6
9 Locate a WIFI or LTE card. 10 Install the WIFI or LTE card WITHOUT their antennas.
PAGE 7
Figure 46. LTE card without antennas 11 Place the WIFI or LTE card into either MC1 or MC2 slot on the VEP4600.
PAGE 8
Figure 47. WIFI and LTE card in VEP4600 12 Align the hole on the VEP4600 WIFI carrier card with the guide pin installed on the motherboard.
PAGE 9
Figure 48. Align WIFI/LTE card on guide pin 13 Push the three blue-marked marked circular locations with two fingers with one hand and one finger of the other hand at the image of a hand with a pointing finger.
PAGE 10
Figure 49. Installation finger push locations 14 Remove the two screws from the installation kit. 15 Install the two screws into the shorter standoffs.
PAGE 11
Figure 50. WIFI, GTE screw locations 16 Re-install the two screws from bottom chassis so the VEP4600 WIFI carrier card is fully connected to the chassis. install the top ten cover screws.
PAGE 12
Figure 51.
PAGE 13
Industry Canada statement: This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de licence.
PAGE 14
This device is intended only for OEM integrators under the following conditions: (For module device use) The antenna must be installed and operated with greater than 20cm between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required.
PAGE 15
End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed and operated with greater than 20cm between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains IC:1514B-E25W001”. Plaque signalétique du produit final Ce module émetteur est autorisé uniquement pour une utilisation dans un appareil où l’antenne peut être installée et utilisée à plus de 20 cm entre l’antenne et les utilisateurs.
PAGE 16
DETACHABLE ANTENNA USAGE This radio transmitter (IC: 1514B-E25W001/ Model: E25W, E25W001) has been approved by ISED to operate with the antenna type listed below with maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
PAGE 17
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
PAGE 18
This device is intended only for OEM integrators under the following conditions: 1) 2) The antenna must be installed such that 20 cm is maintained between the antenna and users, and The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required.
PAGE 19
低功率電波輻射性電機管理辦法第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。