Dell PowerVault MD3060e Storage Enclosure Getting Started Guide Regulatory Model: E08J Series Regulatory Type: E08J001
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Copyright © 2014 Dell Inc. All rights reserved. This product is protected by U.S. and international copyright and intellectual property laws.
Installation And Configuration CAUTION: Before performing the following procedure, review the safety instructions that came with the system. Unpacking A Rack System WARNING: The weight of your system without the physical disks installed (empty weight) is 19.50 kg (43.0 lb) and when fully populated with all the physical disks is 105.20 kg (232.0 lb). WARNING: Your system must be installed by Dell certified service technicians.
Opening And Closing The Disk Drawer Figure 2. Opening and Closing the Disk Drawer Open the disk drawer to install or remove the physical disk carrier(s). NOTE: You can open only one disk drawer at a time. Forcing to open more than one drawer at a time may damage the assembly or produce unexpected results. Installing The Physical Disks Figure 3. Installing the Physical Disk(s) Install physical disk(s) in the disk drawer. NOTE: You may receive multiple drives with carriers in separate boxes.
Connecting The Power Cable(s) Figure 4. Connecting the Power Cable(s) Connect the system’s power cable(s) to the system. Securing The Power Cable(s) Figure 5. Securing the Power Cable(s) Open the cable retention bracket by pulling the tabs on its sides, insert the cable, and secure the system power cable, as shown in the illustration.
Turning On The System Figure 6. Turning on the System Turn the power switch on the back of the system to the On position. The power LED will turn on. Installing The Bezel Figure 7. Installing the Bezel Install the bezel as shown in the figure. Other Information You May Need WARNING: See the safety and regulatory information that shipped with your system. Warranty information may be included within this document or as a separate document.
• As a storage enclosure when connected to a Dell PowerEdge server via a Dell qualified Host Bus Adapter (HBA). • When using the MD3060e as a storage enclosure, attached to Dell PowerEdge Server(s), see the following guides: – Dell PowerVault MD3060e Storage Enclosure Deployment Guide — this document provides information about cabling your system and the installation and initial configuration of the Storage Enclosure software. This document is available online at dell.com/powervaultmanuals.
Power NOTE: This system is also designed to be connected to IT power systems with a phase to phase voltage not exceeding 230 V. Battery 6.6 V DC, 1100 mAh, 7.26 W Lithium Ion Battery Physical Height 177.80 mm (7.0 inch) Width 482.60 mm (19.0 inch) with rack latches Depth 825.50 mm (32.5 inch) without bezel and handle Weight (maximum configuration) 105.20 kg (232.0 lb) Weight (empty) 19.50 kg (43.
Environmental Operating One shock pulse in the positive z axis (one pulse on each side of the system) of 31 G for 2.6 m in the operational orientation. Storage Six consecutively executed shock pulses in the positive and negative x, y, and z axes (one pulse on each side of the system) of 71 G for up to 2 m. Altitude Operating –30.5 m to 3048 m (–50 to 10,000 ft). NOTE: For altitudes above 2950 ft, the maximum operating temperature is derated 1.8 ºF/1000 ft. Storage Up to 12,000 m ( 39,370 ft).
Environmental NOTE: Applies to data center and non-data center environments. Gaseous Contamination NOTE: Maximum corrosive contaminant levels measured at ≤50% relative humidity 10 Copper Coupon Corrosion Rate <300 Å/month per Class G1 as defined by ANSI/ ISA71.04-1985. Silver Coupon Corrosion Rate <200 Å/month as defined by AHSRAE TC9.9.
