Dell DR Series System Administrator Guide
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Copyright © 2015 Dell Inc. All rights reserved. This product is protected by U.S. and international copyright and intellectual property laws.
Contents 1 Introduction to the DR Series System Documentation ...................................................... 10 About the DR Series System GUI Documentation.................................................................................................. 10 What's New In This Release.................................................................................................................................. 10 Other Information You May Need........................................................
3 Setting Up the DR Series System Hardware........................................................................ 30 Interacting with the DR Series System...................................................................................................................30 Networking Preparations for the DR Series System........................................................................................30 Connections for Initializing a DR Series System.....................................................
Configuring Share-Level Security...........................................................................................................................54 5 Managing DR Series Storage Operations.............................................................................56 Understanding the Storage Page and Options....................................................................................................... 56 Understanding the Storage Options....................................................
Using the Event Filter........................................................................................................................................81 Monitoring System Health...................................................................................................................................... 82 Using the Dashboard Page to Monitor System Health.................................................................................... 82 Using the Dashboard Health Options..................
Restore Manager (RM)......................................................................................................................................... 104 Downloading the Restore Manager............................................................................................................... 105 Creating the Restore Manager USB Key........................................................................................................105 Running the Restore Manager (RM)...........................
Best Practices: RDA with OST and the DR Series System................................................................................... 124 Setting Client-Side Optimization........................................................................................................................... 124 Configuring an LSU............................................................................................................................................... 125 Installing the RDA with OST Plug-In..........
Supported Virtual Tape Library Access Protocols............................................................................................... 141 NDMP............................................................................................................................................................. 142 iSCSI...............................................................................................................................................................
Introduction to the DR Series System Documentation 1 The DR Series system documentation contains topics that explain how to use the Dell DR Series system to perform data storage operations and manage storage and replication containers. The topics in this administrator’s guide introduce and describe the DR Series system graphical user interface (GUI), which you use to manage your backup and replication operations.
• Dell DR Series System Command Line Reference Guide — provides information about managing DR Series system data backup and replication operations using the DR Series system command line interface (CLI). • Dell DR Series System Getting Started Guide — provides an overview of setting up your DR Series system hardware and includes technical specifications.
Understanding the DR Series System 2 The Dell DR Series system is a high-performance, disk-based backup and recovery appliance that is simple to deploy and manage and offers unsurpassed Total Cost of Ownership benefits. Features such as innovative firmware and an allinclusive licensing model ensure optimal functionality and provide the assurance of no hidden costs for valuable future features.
About the DR Series System The Dell DR Series system is a backup and recovery solution designed to reduce your backup data footprint by using a number of comprehensive backup and deduplication operations that optimize storage savings. The DR Series system is available in the following models: • DR2000v—a Virtual Machine (VM) template for ESX and Hyper-V. • DR4000—which consists of pre-installed DR Series system software on a Dell PowerEdge R510 appliance platform.
enclosures. Adding an expansion shelf provides additional data storage for the DR Series system and also requires a license. Each added expansion shelf enclosure must be equal to or greater than each DR Series system internal drive slot capacity (0–11). For more information, see the topic, “Expansion Unit Limits,” in the Dell DR Series System Interoperability Guide and the related Expansion Shelf topics in this guide.
The DR Series system supports the 64:1 replication of data (32:1 if on the DR4X00 and 8:1 for the DR2000v), whereby up to 64 source DR Series systems can write data to different individual containers on a single, target DR Series system. This supports, for example, the use case where branch or regional offices can each write their own data to a separate, distinct container on a main corporate DR Series system.
The DR Series system uses an active form of replication that lets you configure a primary-backup scheme. During replication, the system processes data storage requests from a specified source to a specified replica target, which acts as a replica of the original source data. This replica can then be cascaded optionally to a third location called a Cascaded replica for an additional copy.
target and replication re-synchronization is done to complete any pending data transfers. Thereby, continuous replication can be done, which reduces network traffic significantly, and data can be replicated and synced with the target in a short amount of time. NOTE: The following scenarios are not supported for seeding: • Import AND export from one share/device cannot occur at the same time. • Import from one share/device cannot be completed from multiple locations at the same time.
2. Set up replication from this container back to the source DR Series system container. 3. Set up a new disk storage unit in the DMA and make sure that the DMA is aware of any new images. 4. Import the old images back into the DMA from the target DR Series system (the original source location). 5. Use a new disk storage unit in the DMA, and then restore the data back to the original client.
CIFS The Common Internet File System (CIFS) remote file access protocol is one supported by the DR Series system, and is also known as a Server Message Block (SMB). SMB occurs more commonly than the Network File System (NFS) protocol on systems that run the Microsoft Windows operating system. CIFS allows programs to request files or services on remote computers.
• • • • • • Allows Full access, object inherit, and container inherit. Applies to This folder, subfolders, and files. CREATOR OWNER: Allows Full access, inherit only, object inherit, and container inherit. Applies to Subfolders and files only. EVERYONE: Allows Traverse folders, execute files, list folders, read data, read attributes, and read extended attributes. Applies to This folder only. NT AUTHORITY\SYSTEM: Allows Full access, object inherit, and container inherit.
• Execute (access that allows user to execute files or traverse directories in the filesystem) NOTE: A root user has all levels of permission access, and a user can be a member of a single group or of multiple groups (up to 32 groups are allowed in Unix). Windows Permissions Guidelines To enable Windows access, the DR Series system supports access control lists (ACLs) that contain zero or more access control entries (ACEs), and an empty ACE list grants all access requests.
All chunking and hash computations are done at the media or client server level. Rapid NFS and Rapid CIFS require you to install a plug-in on the client or media server, depending on your DMA and configuration. For details, see the Configuring and Using Rapid NFS and Rapid CIFS chapter. DR Rapid for the DR Series System DR Rapid is developed by Dell and provides a logical disk interface for use with network storage devices.
• – Control channel uses TCP port 10011 – Data channel uses TCP port 11000 – Optimized write operations enable client-side deduplication Replication operations between DR Series systems: – No configuration required on source or target DR Series systems – Replication is file-based, not container-based – Triggered by DMA optimized duplication operation – DR Series system transfers the data file (not the media server) – After duplication, DR Series system notifies DMA to update its catalog (ack
• Internet Small Computer System Interface (iSCSI) NDMP The Network Data Management protocol (NDMP) is used to control data backup and recovery between primary and secondary storage in a network environment. For example, a NAS server (Filer) can talk to a tape drive for the purposes of a backup. You can use the protocol with a centralized data management application (DMA) to back up data on file servers running on different platforms to tape drives or tape libraries located elsewhere within the network.
the failed drive. The dedicated hot spare remains inactive until it is called upon to replace a failed drive. This scenario is usually encountered when a faulty data drive is replaced. The hot spare can act as replacement for both internal mirrored drives and the RAID 6 drive arrays. Figure 1.
Figure 2.
– Network file protocols and backup client operating systems – Supported web browsers – Supported system limits – Supported OST software and components – Supported RDS software and components – Supported Rapid NFS and Rapid CIFS software and components Terminal Emulation Applications To access the DR Series system command line interface (CLI), the following terminal emulation applications can be used: • FoxTerm • Win32 console • PuTTY • Tera Term Pro NOTE: The listed terminal emulation ap
Figure 3. Dell PowerVault MD1200 Rear Chassis Figure 4. Unified Mode Daisy-Chained Redundant Path Dell PowerVault MD1200 Enclosures Figure 5. SAS Port and Cable Connections (Dell PowerVault MD1200 EMM) 1. 28 SAS cable 2.
Adding a DR Series Hardware System Expansion Shelf To set up, add, and connect an expansion shelf correctly to a DR Series hardware system appliance, you need to complete the following tasks. • Power off the DR Series system. • Install all cabling that connects the external expansion shelf (or shelves) to the DR Series system (For information, see the topic, DR Series System — Expansion Shelf Cabling). • Power on the external expansion shelf (or shelves), and then power on the DR Series system.
Setting Up the DR Series System Hardware 3 You can interact with the DR Series system hardware using one of two supported methods: a web-based graphical user interface (GUI) accessed using a web browser or a command line interface (CLI) using a terminal emulator application (for example, PuTTY). Before you can interact with your system, you must first, however, ensure that the DR Series system is properly set up. NOTE: The topics in this section apply to physical DR Series systems.
To perform an initial configuration, you need: • – An IP address for the system – A subnet mask address – A default gateway address – A DNS suffix address – A primary DNS server IP address – (Optional) A secondary DNS server IP address NIC Connections: To configure NIC connection bonding remember that, by default, the DR Series system will configure its NIC interfaces together as a bonded team (and only one IP address is needed because the bonded NICs assume the primary interface address).
The Initial System Configuration Wizard lets you configure the following network settings to complete a first-time initialization of your system: • IP addressing mode • Subnet mask address • Default gateway address • DNS suffix address • Primary DNS server IP address • (Optional) Secondary DNS server IP address • Host name for system Default IP Address and Subnet Mask Address This topic lists the following default address values that can be used for initialization of a DR Series system: • IP
NOTE: For details about logging in and using the Initial System Configuration Wizard, see Configuring Networking Settings. Local Console Connection To configure a local console connection, you must make the following two rear chassis cable connections: • VGA port and your video monitor • USB port and your keyboard To make local console cable connections for the DR Series system appliance, complete the following: 1.
5. (DR4100/DR6000 system) Locate the VGA monitor port and the USB ports on the back of your system. See Figure 3 for the VGA and USB port locations and complete steps 5 to 8. 6. Connect the video monitor to the VGA port on the back of your system (see item 2 in the DR4100/DR6000 System Rear Chassis Port Locations table). 7. Connect the USB keyboard to one of the two USB ports on the back of your system (see item 3 in the DR4100/ DR6000 System Rear Chassis Port Locations table). 8.
management functions for the DR Series system. iDRAC connections are configured using console redirection and the iDRAC6/7 web interface. The login values you can use for making iDRAC connections are: • • • Default username: root Default password: calvin Default static IP address: 192.168.0.120 For information on how to configure the iDRAC, see the Dell RACADM Reference Guides at support.dell.com/manuals and Accessing iDRAC6/iDRAC7 Using RACADM.
11. To change the default host name (for example, the serial number of the DR Series hardware appliance), type y (for yes) and press . If you responded yes, type the host name you want to use, and press . After you configure your host name response, the current system settings are displayed. 12. To accept these settings, type y (for yes), and press . 13. If you want to change any of these settings, type n (for no), and press . Modify the settings as needed, and press .
NOTE: For best results when using IE web browsers in combination with supported Windows-based servers, ensure that Active Scripting (JavaScript) is enabled on the Windows client. This setting is often disabled by default on Windows-based servers. For more information on enabling Active Scripting, see Enabling Active Scripting in Windows IE Browsers. NOTE: If you want to reset your login password, click Reset Password on the DR Series System Login page. The Reset Password dialog is displayed.
Dell recommends that you verify the system can accept your bonding selection type. The connection will be lost unless it is correctly configured. For more information, see Configuring Networking Settings. d. In Bonding, enter the MTU value for the maximum transmission unit (the MTU accepts values between 512 and 9000). For more information, see Configuring Networking Settings. e.
NOTE: When logged in, a Logout Confirmation dialog is displayed after 45 minutes of non-use. This dialog displays for 30 seconds before the DR Series system performs a forced timeout. Click Continue to reset the 45-minute logout timer. If you do not click Continue before the 30-second interval elapses, the DR Series system logs you out. You must log in again to resume using the DR Series system features and GUI.
3. Using the right scroll bar, scroll down the Settings choices until you reach Scripting. 4. In Active scripting, click Enable. 5. Click OK to enable JavaScript and the Active Scripting feature for your web browser. The Internet Options page is displayed. 6. Click OK to close the Internet Options page.
Configuring the DR Series System Settings 4 This topic introduces the concept that before you can run any DR Series system operations, you first need to understand the following key tasks: • How to initialize the system • How to shut down or reboot the system • How to manage the system password Initializing the DR Series system requires that you configure and manage a number of very important system settings.
– • • Slave Interfaces Eth0 – MAC – Maximum Speed – Speed – Duplex Eth1 – MAC – Maximum Speed – Speed – Duplex To configure new networking settings (or to change from those set using the Initial System Configuration Wizard), complete the following: 1. Select System Configuration → Networking. The Networking page is displayed. Select settings for hostname, IP Address, DNS, Bonding, or to view the Ethernet port settings (Eth0-Eth3) for the DR Series system.
NOTE: Ensure that the value that you enter in MTU is the same for the clients, Ethernet Switch, and the appliance. The connection between the clients, the Ethernet switches, and the appliance will break if the MTU number is not the same on all the components. NOTE: In computer networking, jumbo frames are Ethernet frames with more than 1500 bytes of payload (but in some cases, jumbo frames can carry up to 9000 bytes of payload).
11. In Domain Suffix, type a domain suffix to use. For example, acme.local. This is a required field. 12. In Primary DNS, type an IP address that represents the primary DNS server for your system; this is a required field. 13. For Secondary DNS, type an IP address that represents the secondary DNS server for your system; this is an optional field. 14. Click Submit to have the DR Series system accept the new values (or click Cancel to display the Networking page).
Eth3: • MAC: 00:30:59:9A:00:99 • Speed: 1000Mb/s • Max Speed: 1000baseT/Full • Duplex: Full Managing the DR Series System Password You can manage the login password that is used when logging in to the DR Series system in two ways: • By modifying the existing login password using the Edit Password option in the System Configuration page. For more information, see Modifying the System Password.
3. To log in using the default password, type St0r@ge! , and click Login. NOTE: After you have reset the login password to its default and logged in to the DR Series system, Dell recommends for security reasons that you create a new unique login password. 4. In Service Tag, type the Service Tag associated with your system.
The System has successfully rebooted dialog is displayed after rebooting (system reboot may take up to 10 minutes to complete). Configuring Active Directory Settings You need to configure the Active Directory setting to direct your DR Series system to join or leave a domain that contains a Microsoft Active Directory Service (ADS). To join an ADS domain, complete steps 1 through 4 in the following procedure (to leave an ADS domain, skip to step 5).
Configuring Local Workgroup Users Settings You need to configure settings to create a local workgroup of CIFS authenticated users. This capability lets you create a local workgroup (Local Workgroup Users) to which you can add new users, edit existing users, or delete users from the workgroup. To configure the DR Series system for a Local Workgroup Users, complete the following: 1. Select System Configuration → Local Workgroup Users. The Local Workgroup Users (CIFS) page is displayed. 2.
3. In Email Address, type a valid email address using the address format that your email system supports. 4. Click Submit to configure the recipient email address (or click Cancel to display the Email Alerts page). The Email Alerts page is displayed, and an Added email recipient dialog is displayed when successful. 5. To create additional recipient email addresses, repeat steps 2 through 4.
Configuring Administrator Contact Information You can configure the administrator contact information to identify the person who is actively managing or responsible for your DR Series system acting as its administrator. To do this, enter contact information for the administrator on the Administrator Contact Information page using the Edit Contact Information option.
Editing Administrator Contact Information To edit the contact information for an existing system administrator, complete the following: 1. Select System Configuration→ Admin Contact Info. The Administrator Contact Information page is displayed. 2. Click Edit Contact Info on the options bar. The Edit Administrator Contact Information dialog is displayed. 3. Modify the notification selections as needed. 4. Click Submit.
4. To use the service tag and administrator e-mail, select Service Tag and Administrator Email. The optional security questions area is displayed. 5. To set the optional security questions, under Optional Security Question 1 and Optional Security Question 2 in Question enter the security question. 6. In Answer , enter the answer to your security question. NOTE: Save the answer in a secure location, you will need these answers to reset the DR Series system password. 7. Click Submit.
The Email Relay Host page is displayed, and an Updated external email server information dialog is displayed when successful. Configuring System Date and Time Settings If you need to configure or manage the date and time settings used by your system that synchronize it with other DR Series systems or clients running in your domain, navigate to the Date and Time page, and click Edit.
NOTE: If the DR Series system is joined to a Microsoft Active Directory Services (ADS) domain, the Edit option will be disabled (grayed out) and the Mode, Time Zone, or Date and Time values cannot be changed in the Settings pane. This is because whenever a DR Series system is joined to a domain, the Network Time Protocol (NTP) is disabled and the DR Series system uses the domain-based time service. NTP is used in the Mode setting when the DR Series system is part of a workgroup and not joined to a domain.
This administrative tool lets you control access to shares and also configure read-only or read-write access to user groups or individual users within the Active Directory Service (ADS) when joined to an ADS domain. To implement share-level security on a DR Series system that has been joined to an ADS domain, make sure that you have mapped a drive on the DR Series system using an account with DOMAIN\Administrator credentials (or by using an account that is equivalent to a domain administrator).
Managing DR Series Storage Operations 5 This chapter describes how to use the DR Series system to perform data storage operations, including creating and managing containers, setting up and managing replication, viewing detailed client information, and setting up and managing encryption. Understanding the Storage Page and Options To open the Storage page, click Dashboard → Storage.
Understanding the Storage Options The DR Series system stores backed up and deduplicated data that has been ingested by the system into easily accessible storage containers. A number of system storage operations are available in the DR Series system graphical user interface (GUI) that simplify the process for storing this type of data.
NOTE: Use Select to identify the container on which you want to perform an action. For example, click Select, and click Display Statistics to display the Container Statistics page for the container you selected. Replication Page To display the Replication page, click Storage → Replication. The Replication page displays the number of source replications, the names of the local and remote containers, the peer state, and the bandwidth selected per container.
• Plug-In — The plug-in type installed on each client. • Backup Software — The backup software used with each client. • Idle Time — The idle time (non-activity) for each client. • Connection — The number of connections for each client. • Mode — The current mode type for each client. Clients Page (Using the NFS or CIFS Tabs) On the Clients page (Storage→ Clients), click the NFS or CIFS tab to view the following information for NFS or CIFS clients.
• If an OST or RDS client is set to run in Auto mode, the OST or RDS client will run in the mode setting determined by the media server. The following table shows the relationship between the configured OST or RDS client mode types and the supported client mode based on client architecture type and corresponding number of CPU cores. For information about Rapid NFS and Rapid CIFS supported client modes based on architecture and CPU cores, see Best Practices: Rapid NFS and Best Practices: Rapid CIFS.
Managing Container Operations This topic describes using the DR Series system to manage your data storage and container operations. Data storage operations include tasks such as creating new containers, managing or deleting existing containers, moving data into containers, and displaying current container statistics. Creating Storage Containers By default, the DR Series system provides a container named backup for your use after you complete the basic system configuration and initialization process.
6. For Marker Type, select the appropriate marker that supports your DMA. • None — Disables marker detection for the container. • Auto — Automatically detects CommVault, Tivoli Storage Manager (TSM), ARCserve, and HP Data Protector marker types. In addition, select this option if you need to support EMC Networker 2.0. • Networker — Supports EMC Networker 3.0. If you need to support EMC Networker 2.0, select Auto. • Unix Dump — Supports the Amanda marker, among others.
access clients list box. (To delete an existing client from this list box, select the IP address (or FQDN hostname) of the client you want to delete, and click Remove. The “deleted” client disappears from the list box.) NOTE: The DR Series system administrator that manages the system has a different set of privileges than does the CIFS administrator user. Only the DR Series system administrator can change the password for the CIFS administrator user.
• 800 GB • 400 GB • 200 GB • 100 GB • 50 GB • 10 GB NOTE: Creating a VTL container type creates a tape library of type Storage Tek L700 with 10 tape drives of type IBM Ultrium LTO-4 and 10 tape slots holding 10 tapes. Additional tapes can be added as required. For more information, see the topic, VTL and DR Series Specifications. 8. 9. For Access Protocol, select one of the following options. • NDMP • iSCSI • No Access (select this option if you are not ready to select a protocol.
For iSCSI, you should configure the CHAP password for the system-wide CHAP account. To do so, you can use the CLI or navigate to Storage > Clients, and then click Edit CHAP Password. You can add additional tapes to the library after container creation by editing the container in the GUI or by using the following CLI command: vtl --update_carts –-name --add --no_of_tapes NOTE: For more information about using the command line interface, see the Dell DR Series Command Line Reference Guide.
3. Modify the marker type for the selected container as needed. For details, see the topic, Creating Storage Containers. CAUTION: If you are changing the marker type on a DR6000 and you are using Rapid CIFS, you must remount the share on the client after you change the marker type. 4. Modify the connection type options for the selected container as needed.
The Network page is displayed, which lists all current computers. 2. In the browser Address bar, click Network to select your DR Series hostname or IP address. The Network page is displayed, which lists all current storage and replication containers. NOTE: However, if your DR Series system is not listed, you can enter its hostname or IP Address preceded by "https://" and followed by the container name in the Address bar to access it (for example in this format, https://10.10.20.20/container-1).
• Post Dedupe Bytes (number of bytes after deduplication) • Post Compression Bytes (number of bytes after compression) • Post Encryption Bytes • Post Encryption Bytes in GiB • Compression Status (current compression status) • Cleaner Status (current space reclamation process status) • Encryption Status • Total Inodes (total number of data structures) • Bytes decrypted • Dedupe Savings (deduplication storage savings by percentage) • Compression Savings (compression storage savings by per
• Total Inodes (total number of data structures in container) • Read Throughput (read throughput rate in Mebibytes or MiB/s for container) • Write Throughput (write throughput rate in MiB/s for container) • Current Files (current number of files in container) • Current Bytes (current number of ingested bytes in container) • Cleaner Status (current space reclamation process status for the selected container) For more information on DR Series system CLI commands, see the Dell DR Series System Comm
Refer to the Dell DR Series System Interoperability Guide for details about the supported system limits for replication per DR Series system model. For a definition of connections and streams, see Streams_vs_Connections. • Version Checking — The DR Series system software includes version checking that limits replication only between other DR Series systems that run the same system software release version.
CAUTION: Exercise care when configuring the direction of replication for source and target containers. For example, target containers can have their contents deleted if they contain existing data. NOTE: Because you cannot modify an existing defined role (source or target replica) for a replication relationship, if necessary, you must delete the existing replication relationship, and then recreate a new relationship with the specific source and target roles that you want. 1. Select Storage→ Replication.
4. To start the scheduled replication process, click Start, and click OK to start replication (or click Cancel to display the Replication page). The Successfully started replication dialog is displayed. Adding a Cascaded Replica To add a cascaded replica to an existing replication relationship, complete the following steps. 1. Select Storage→ Replication. 2. On the Replication page, select the replication relationship for which you want to add a cascaded replica, and then click Edit.
5. • Network Average Transfer Rate—in KB/s • Network Peak Transfer Rate—in KB/s • Network Bytes Sent • Estimated Time to Sync • Dedupe Network Savings • Compression Network Savings • Last INSYNC Time—indicates the last time system synchronization occurred. • Schedule Status To apply filtering, in the upper right corner, select Filter. In the Replication Filter dialog box, select the replication segment hostname(s) by which you want to filter statistics, and then click Apply Filter.
Daily Replication Schedule Example The daily Replication schedule example in this topic illustrates the process for setting up a replication schedule that uses a 24-hour clock (the time keeping convention where time of day is defined on a 24–hour basis). You set or view a Replication schedule in the Replication Schedule page. For more information, see Creating a Replication Schedule. NOTE: Replication schedules can only be set on individual replication-enabled source containers.
The Encryption page is displayed, which displays the current encryption status of the DR Series system. 2. Click Set or Change Passphrase. The Set or Change Passphrase dialog box opens. 3. In the Passphrase and Confirm Passphrase text boxes, enter the passphrase to be used to encrypt content encryption keys. When creating a passphrase, follow these guidelines: • The passphrase string can take up to 256 characters. • Alphanumeric and special characters can be entered as part of the passphrase string.
• 4. Static — A global, fixed key is used to encrypt all data. • Internal — Content encryption keys are generated and rotated on a specified period of days. If you selected Internal as the mode of key management, next to Key Rotation Interval in Days, enter the number of days for key rotation when a new key is to be generated. The minimum number of days before the content encryption key can be rotated, and a new key is generated is seven days. 5. Click the Submit Encryption Settings button.
Monitoring the DR Series System 6 NOTE: The topics in this section apply to physical DR Series systems. The virtual DR Series system, DR2000v, may have different options available. For details, see the Dell DR2000v Deployment Guide for your specific VM platform and the Dell DR Series System Interoperability Guide. For more information on the DR Series system CLI commands, see the Dell DR Series System Command Line Reference Guide.
• Number of Alerts, see Monitoring System Alerts. • Number of Events, see Monitoring System Events. Location Status Icon Description System Status bar Represents an optimal state. System Status bar Represents a warning state (a non-critical error was detected). System Status bar Represents an actionable state (a critical error was detected). NOTE: To display specific information about the current HW State, click the link to display the Health page.
• Current Date/Time • Current Time Zone • Cleaner Status • Total Savings (in percentage) • Total Number of Files in All Containers • Number of Containers • Number of Containers Replicated • Active Bytes (total bytes before optimization) • Advanced Data Protection (status of data integrity check) • Encryption Status (such as Done, Running, Pending, or Disabled) NOTE: To display additional information about certain elements in the DR Series system GUI, click the corresponding Question Mark
• Message (a brief description of the alert; for example, Network Interface Controller Embedded (LOM) Port 2 disconnected. Connect it to a network and/or check your network switches or routers for network connectivity issues). Monitoring System Events You can monitor the DR Series system events, and filter events you want to display using the Event Filter pane in the Events page.
• Set the number of events to display per page: click Events per page at the lower-right corner of the table and select either 25 or 50 events to display per page. • Use the scroll bar to display each full page of system events. • 8. To display other pages of system events, click prev or next, click on a specific page number, or enter a page number in the Goto page and click Go to display that page of system events.
5. • Click Done. Click the Calendar icon (adjacent to Timestamp To) to configure an end setpoint. To configure an end setpoint, complete the following: 6. • Select the desired day in the current month, or click the left or right arrow in the month title bar to select a previous or later month. • Adjust the Hour and Minute sliders to the desired time (or click Now to set the date and time to be the current date and time in hours and minutes). • Click Done.
• NIC • CPU • DIMM • NVRAM Enclosure — System Hardware Health components • Power Supplies • Fans • Temperature • Storage • Enclosure Management Module (EMM) Using the Dashboard Health Options To use the navigation panel to display the current system status of the DR Series system components (or any expansion shelf enclosure) that are installed, complete the following steps: 1. Click Dashboard → Health. The Health page is displayed. 2.
ALB and the 802.3ad are link aggregation methods that aggregate or combine multiple network connections in parallel to increase throughput beyond what a single connection could support. Link aggregation for Ethernet connections also provides redundancy, in case one of the links fails. The DR Series system also comes with a Serial-Attached SCSI (SAS) card for future enhancements. The DR Series system ships equipped with the 1-GbE, I-GbE, or 10-GbE SFP+ NIC.
Setting a Latest Range Value To set a Latest Range value and display system status results based on this setting, complete the following: 1. Click Dashboard → Usage. The Usage page is displayed. 2. Click Latest Range. 3. Select the desired duration period (Hours, Days, or Months) in the Range drop-down list. By default, Hours is the first displayed duration option in the drop-down list. 4. Select a value in the Display last... drop-down list that matches the Range duration time period you selected.
• Marker Type • Connection Type • Replication (if enabled) • Library/Slots/Access Control List (for VTL type containers only) For more information, see Editing Container Settings. Displaying the Container Statistics Page To display container statistics for a selected container, complete the following: 1. Click Dashboard→ Container Statistics. 2. In the Container Name: drop-down list, select the container for which you want to view statistics. The Container Statistics page is displayed.
• 7. – Library — displays information in a table about the vendor and model information for medium changer and tape drives. The Info Column in the first row of the table indicates the total number of tapes and tape size of the VTL container. – Access Control List — For NDMP connection types, displays the IP address or the FQDN of the DMA that has access to this VTL container, or, for iSCSI connection types, displays the “Inititators Allowed” for the container.
• Click Peer System, press Ctrl, and select the peer systems in the list box to select one or more peer DR Series systems in the list that you want to display. NOTE: Only one of the Container Filter options can be active at any one time (they are mutually exclusive). 3.
• Replication Average Throughput (in Kebibytes per second, KiB/s) • Replication Maximum Throughput (in KiB/s) • Network Average Throughput (average throughput rate in KiB/s) • Network Maximum Throughput (maximum throughput rate in KiB/s) • Network Bytes Sent (total network bytes sent in Mebibytes/MiB) • Dedupe Network Savings (total deduplication network savings in percentage) • Compression Network Savings (total compression network savings in percentage) • Last INSYNC Time (date of last sync
Using Global View 7 This topic describes how to monitor and navigate to multiple DR systems in your enterprise using the Global View feature, which provides a real-time view of multiple DR systems in your enterprise. About Global Views The Global View is a dashboard that provides a holistic picture of all DR Series systems added to it, making it easy to monitor and manage remote systems. For example, suppose you are an administrator in a headquarters office with a DR Series system.
• All DR Series systems must be in the same Active Directory Services (ADS) domain, in the same login group, and have identical login credentials. This includes the system to which you are currently logged in. For details, see the procedures that follow. • When you use Global View, you must log in to the DR Series system using your domain credentials; for example, you must log in as DOMAIN\Administrator instead of Administrator.
Adding a Login Group in an ADS Domain After you configure your DR systems within the same ADS domain, you must ensure that a login group exists and add it to the domain. Adding a login group is only possible when the DR Series system is already joined to a domain. Also, you must be logged in as a domain user that is part of an enabled login group. To add a login group in an ADS domain, complete the following: 1. Select System Configuration → Active Directory. The Active Directory page is displayed.
Global View Summary NOTE: If an alert is displayed with a message that "Member units will fail to connect because non-Active Directory credentials were used", see Prerequisites. The following table describes the statistics available in the Global View Summary: NOTE: The statistical values refresh every 15 seconds. NOTE: If you used the command line interface (CLI) to join the DR Series system into the Active Directory domain, you may notice Global View contains multiple, unnecessary entries.
Item Description Active Bytes Displays the total bytes before optimization in all appliances in the Global View. Active Clients Displays the total clients configured in all appliances in the Global View, organized by container connection type. Appliance List This section lists all appliances in the Global View with a high-level snapshot of their status. By default, appliances are listed in alphabetic order by Appliance Name.
Item Description TiBs). The capacity appears as a progress bar with a percentage shown. When the capacity is less than 90%, the capacity bar is green. After the capacity used reaches 90%, the capacity bar is shown in red. Hover your mouse over the Capacity percentage bar to display the following information: • • • Savings Used Capacity (GiB) Free Capacity (GiB) Total Capacity (GiB) Displays the total savings as a percentage (combining both deduplication and compression) over a time period (in minutes).
The selected DR Series system is displayed in a new browser window. If you are using Internet Explorer 10, make sure the pop-up blocker is disabled in order to have the selected DR Series system open in a new browser window. NOTE: When you initially navigate to a DR Series system, you will need to accept a browser certificate exception. After you accept it, the exception does not appear again unless you clear your browser cache.
column next to the appliance. If one or more red icons are displayed, the Reconnect Units link is enabled on the Global View page. To reconnect a DR Series system to the Global View, complete the following: 1. On the Global View page, click Reconnect Units. The Reconnect DR Units dialog box appears. 2. In Domain Name (FQDN), enter the fully-qualified domain name (FQDN) in which the DR Series system resides.
Using the DR Series System Support Options 8 You can use the Support page and its Diagnostics, Software Upgrade, and License options to maintain the state of your DR Series system. To access these options, use the DR Series system navigation panel (for example, click Support→ Diagnostics to display the Diagnostics page) or use the Diagnostics, Software Upgrade, or License links on the Support page.
NOTE: For more information about diagnostics log files, log file directories, and the Diagnostics service, see About The Diagnostics Service. A DR Series diagnostics log file is a bundle that contains a variety of file types that record the latest system settings, and saves them in a compressed .lzip file format. The Diagnostics page identifies each diagnostics log file by the following attributes: • File name—in this format, __
The diagnostics log file bundle is identical to one created using the DR Series system CLI diagnostics --collect --dset command. System diagnostics information can assist Dell Support when troubleshooting or evaluating your DR Series system. To generate a diagnostics log file bundle for your system, complete the following: 1. Select Support → Diagnostics in the navigation panel. The Diagnostics page is displayed, and this page lists all current diagnostics log files. 2. Click Generate.
Deleting a Diagnostics Log File To delete an existing diagnostics log file from the Diagnostics summary table on the Diagnostics page, complete the following: 1. Select Support → Diagnostics. The Diagnostics page is displayed. 2. Click Select to select the diagnostics file you want to delete, and click Delete. The Delete Confirmation dialog is displayed. 3. Click OK to delete the selected diagnostics log file (or click Cancel to display the Diagnostics page).
Verifying the Current Software Version To verify the currently installed version of the DR Series system software, complete the following: NOTE: You can verify the version of the installed DR Series system software in the Dashboard page (in the System Information pane), the Support page (in the Support Information pane), and the Software Upgrade page (in the Software Information pane). The following procedure documents the process from the Software Upgrade page. 1.
There are only three possible outcomes during a DR Series system software upgrade operation: • Upgrade has completed successfully—no reboot is required. • Upgrade has completed successfully—but a reboot is required (click Reboot in the Software Upgrade page). • Upgrade has failed. NOTE: If the DR Series system software upgrade operation fails, you can reboot the system and attempt another software upgrade operation using the DR Series system GUI.
To reset an SSL certificate, complete the following steps: 1. Select Support → SSL Certificate in the navigation panel. The SSL Certificate page is displayed. 2. In the upper right corner of the page, click Reset SSL Certificate. NOTE: You can also use the command line interface (CLI) command, “maintenance -- configuration -reset_web_certificate”. Refer to the Dell DR Series Command Line Reference Guide for more information.
RM can also be used to reset the system back to its initial factory settings when moving it from a test environment to a production environment. RM supports the following two modes: • Recover Appliance—in Recover Appliance mode, RM reinstalls the operating system and attempts to recover the prior system configuration and the data residing in the containers.
Running the Restore Manager (RM) To run the Dell Restore Manager (RM) utility, boot the DR Series system using the RM USB key created in Creating the RM USB key). 1. Insert the RM USB key into an available USB port on the system. You can also use the virtual media option of iDRAC to remotely load the RM USB key. For more information, see Configuring and Using Virtual Media in the Integrated Dell Remote Access Controller 6 (iDRAC6) User Guide at support.dell.com/support/edocs/software/smdrac3/. 2.
Hardware Removal or Replacement To properly remove or replace any DR Series system hardware, you must observe and use the best practice shut down and start up procedures. For a comprehensive set of removal and replacement procedures with step-by-step instructions, see the Dell DR Series System Owner’s Manual. For more information about the best practices, see DR Series System: Proper Shut Down and Start Up and Shutting Down the DR Series System.
NOTE: Dell recommends the following supported method for flushing DR Series system data from the NVRAM to the RAID6 before replacing the NVRAM by using either of the following DR Series system CLI commands: system --shutdown or system --reboot. NOTE: If you need to remove or replace the NVRAM in the DR Series system, see Shutting Down the DR Series System and NVRAM Field Replacement.
9 Configuring and Using Rapid NFS and Rapid CIFS Rapid NFS and Rapid CIFS enable write operation acceleration on clients that use NFS and CIFS file system protocols. Similar to OST and RDS, these accelerators allow for better coordination and integration between DR Series system backup, restore, and optimized duplication operations with Data Management Applications (DMAs) such as CommVault, EMC Networker, and Tivoli Storage Manager.
The Rapid NFS plugin (driver) must be installed on client systems After the plug-in is installed, write operations will go through Rapid NFS while metadata operations such as file creates and permission changes will go through the standard NFS protocol. Rapid NFS can be disabled by uninstalling the plug-in. Markers must be set on the client, not in the DR Series GUI If you are using a DMA that supports a marker, should explicitly set it.
Best Practices: Rapid CIFS This topic introduces some recommended best practices for using Rapid CIFS operations with the DR Series system. Containers must be of RDA containers cannot use Rapid CIFS. If you have existing NFS/CIFS containers, you do not type NFS/CIFS need to create new containers to use Rapid CIFS; you can install the plug-in (driver) to existing clients.
Installing the Rapid NFS Plug-In The Dell Rapid NFS plug-in must be installed on to the media server type you choose (for supported operating systems and DMAs, see the Dell DR Series System Interoperability Guide). The plug-in software enables integration between DR Series system data storage operations and the supported data management applications (DMAs). Before you install, make sure you adhere to the Best Practices covered in another topic in this chapter.
NOTE: If you want to do a mount on AIX, you must set the nfs_use_reserved_ports and portcheck parameters first. The parameters cannot be set to 0. For example: root@aixhost1 / # nfso -po portcheck=1 root@aixhost1 / # nfso -po nfs_use_reserved_ports=1 To ensure that the plug-in is running successfully, check the log file at: tail -f /var/log/oca/rdnfs.log.
Viewing the Rapid NFS and Rapid CIFS Logs This topic contains information about locating and reviewing Rapid NFS and Rapid CIFS event logs in order to troubleshoot. Viewing Rapid NFS Logs The Rapid NFS log is located at /var/log/rdnfs.log.
Uninstalling the Rapid NFS Plug-In Use the following procedure to remove the Dell Rapid NFS plug-in from a Linux-based media server. After you uninstall the plug-in, Rapid NFS will be disabled and “inactive” will be shown next to NFS Write Accelerator on the NFS Connection Configuration pane on the Container Statistics page. NOTE: Dell recommends that you retain the Dell Rapid NFS plug-in installer on the media server in case you need to use it to reinstall the plug-in.
10 Configuring and Using Rapid Data Access with Dell NetVault Backup and with Dell vRanger Overview Rapid Data Access (RDA) with Dell NetVault Backup and with Dell vRanger provides the logical disk interface that can be used with network storage devices. The Dell DR Series system requires a DR Rapid plug-in to integrate its data storage operations with NetVault Backup and vRanger.
Guidelines for using RDA with NetVault Backup and with vRanger For best results, observe the following guidelines for optimal performance with your supported RDA with NetVault Backup and RDA with vRanger operations with the DR Series system: • Backup, restore, and optimized duplication operations are performed using the RDA with NetVault Backup or RDA with vRanger plug-in. NOTE: The plug-in is installed on client systems to support client-side deduplication. • Deduplication.
You can turn On or turn Off client-side optimization by using the CLI commands, rda --update_client --name --mode. For more information about DR Series system CLI commands, see the Dell DR Series System Command Line Reference Guide located at dell.com/powervaultmanuals (by selecting your particular DR Series system). Adding RDS Devices in NetVault Backup To add RDS devices in NetVault Backup: 1. Start the NetVault Web user interface (UI), and log on to the NetVault Backup Server. 2.
Backing Up Data on the RDS Container Using NetVault Backup You must back up data on the RDS container (available on the DR Series systems) using NetVault Backup. Before you can back up data using the RDS protocol, you must create an RDS container on the DR Series system and then add that container as an RDA device on NetVault Backup. For more information see, Adding RDS Devices in NVBU. To back up data on the RDS container: 1.
3. In Job Title, enter a relevant job title. 4. In the Selections tab, select Data Copy and then Backups or Backup Sets, and navigate to the backup job that you want to replicate. 5. Select the Backup Options tab, under Data Copy Options select the relevant options. NOTE: Under Copy Type, by default, options are set for Copy and Optimized replication for the DR Series systems. 6.
• 7. To restore data to an alternate client, select the target client in the list. • Alternatively, click Choose. In the Choose the Target Client dialog box, select the client, and click OK. In the Schedule list, select an existing Schedule Set, or click Create New, and configure the schedule type and schedule method. To run the job as soon as it is submitted, use the "Immediate" set. For more information about these options, see the Dell NetVault Backup Administrator's Guide. 8.
Configuring and Using RDA with OST 11 This topic introduces key RDA with OST tasks and provides links to other related topics that contain procedures that describe how to perform these tasks: • Configuring the DR Series system for use with OST and the supported DMAs; for more information, see Configuring the DR Series System Using the Backup Exec GUI, and Configuring DR Series System Information Using NetBackup • Configuring the Logical Storage Unit (LSU) using the DR Series system GUI; for more inform
• – DR Series system storage capabilities can be used without extensive changes to DMAs – Backup and replication operations are simplified by using built-in DMA policies DR Series system and RDA with OST ports and write operations: – • Control channel uses TCP port 10011 – Data channel uses TCP port 11000 – Optimized write operations enable client-side deduplication Replication operations between DR Series systems: – No configuration is required on the source or target DR Series system – Repl
Term Description LSU Logical Storage Unit, which from the DR Series system perspective, represents any container created for data storage. LSU is a common storage term while container is a common term in DR Series systems that represents a location for storing data. media server This is the host running the DMA media server and is where the RDA with OST plug-in is installed. The RDA with OST plug-in can also be installed on a client.
Configuring an LSU You can configure a logical storage unit (LSU) as an OpenStorage Technology (OST) connection type container for data storage by using the DR Series system GUI. To configure an LSU as an OST connection type container, log in to the DR Series system and complete the following: 1. Navigate to the Containers page (in the Dashboard navigation panel). 2. Click Create to create a new container. 3. In Container Name, enter a name for the container. 4.
usage: DellOSTPlugin-xxxxx-x86_64.
5. In the Welcome page, click Next to continue. The End-User License Agreement page is displayed. 6. Click I accept the terms in the License Agreement, and click Next. 7. In the Destination Folder page, accept the default destination location, and click Next. 8. In the Ready to Install Dell Storage Plug-In for Symantec OST page, click Install. When the plug-in has been installed, the Completed the Dell Storage Plug-In for Symantec OST Setup Wizard page is displayed. 9.
4. Click Yes to uninstall the plug-in. Installing the RDA with OST Plug-In for NetBackup on Linux This topic describes how to install the RDA with OST plug-in on a media server running the supported Red Hat Enterprise Linux or SUSE Linux server operating system software (using the NetBackup DMA). Ensure that you have downloaded the RDA with OST plug-in installer into the correct directory on the designated media server. The plug-in installer is saved as DellOSTPlugin-xxxxx-x86_64.bin.
4. Retain the plug-in installer on the media server in case you need to use it to reinstall the plug-in. Configuring DR Series System Information Using NetBackup The topic introduces the concept of configuring the DR Series system information using the NetBackup media server command line interface (CLI) commands and graphical user interface (GUI) menus, tabs, and options. The NetBackup CLI commands and GUI menus, tabs, and options allow you to configure both the Linux or Windows media servers.
The Storage Server Configuration Wizard page is displayed, which is where you can add a storage server. 2. Select OpenStorage to choose the type of disk storage that you want to configure in this window, and click Next. 3. Enter the following values to configure a storage server: The Add Storage Server page is displayed. • In Storage server type, enter DELL. • In Storage server name, enter the name of the DR Series system.
Creating Disk Pools From LSUs Use the NetBackup graphical user interface (GUI) to configure disk pools from logical storage units (LSUs) on the DR Series system. Log in to NetBackup, and complete the following: 1. In the main window of the NetBackup Administrator console, click Configure Disk Pools to launch the Disk Pool Configuration Wizard. The Disk Pool Configuration Wizard page is displayed, which is where you define media servers for use in a disk pool. 2.
4. Click OK to create the new storage unit. Backing Up Data From a DR Series System (NetBackup) This topic describes how to use NetBackup to back up data from a DR Series system. Before backing up data, you first need to configure a policy that creates a backup on the OST logical storage unit (LSU). This type of policy is similar to what is done for network-attached storage (NAS) shares, except that when defining policy attributes, you need to select the LSU that contains the OST disk pool.
5. In the Setup Duplication Variables page, select the LSU that is the target DR Series system in the Storage unit dropdown list, and click OK. 6. To monitor the status of any duplicate image operation, perform the following: a. Click Activity Monitor in the left navigation pane of the NetBackup Administrator console. b. Select the data duplication job in which you are interested. c. View the operation details.
8. In the Backup Exec Administrator page, click the Devices tab, and right-click on the local system name that is listed as the root node. A drop-down list of device-related options is displayed. 9. Select Add OpenStorage in the drop-down list. The Add OpenStorage Device page is displayed. 10. Configure the Add OpenStorage Device page with the following information, and click OK: • • Server—enter the host name or IP address of the DR Series system.
for the source file, while the other entry is for the target file. The backup administrator can restore backup data from either appliance in case of data loss or disaster. To optimize duplication between DR Series systems, create an additional OST device that points to the target DR Series system, and complete the following steps: 1. 2. Launch the Backup Exec Administrator console, select the Devices tab, and right-click the target DR Series system. Select Add OpenStorage in the drop-down list.
• auto (--mode auto) DR will set the deduplication to Dedupe or Passthrough, based on the client’s number of cores and whether it is 32– or 64–bit. These OST commands are used in the following format: ost --update_client --name --mode. NOTE: If a RDA with OST client has four or more CPU cores, it is considered to be dedupe-capable. However, the client operating mode depends upon how it is configured in the DR Series system (Dedupe is the default RDA with OST client mode).
NOTE: The --files in the ost --show --file_history command represents replicated files that were processed via the DMA optimized duplication operation. This command displays only up to the last 10 such files. The --name in the ost --show --name command represents the OST container name. NOTE: For more information about OST-related DR Series system CLI commands, see the Dell DR Series System Command Line Reference Guide.
Rotating RDA with OST Plug-In Logs for Linux If you set the RDA with OST plug-in log level to Debug, this can cause the plug-in log to quickly grow in size. The best practice for preventing any issues with log sizes is to rotate the plug-in logs using the logrotate utility that is commonly available on Linux-based systems. To configure log rotation, complete the following: 1. Create a file in /etc/logrotate.d/, name it “ost”, and add the following entries: /var/log/libstspiDell.
Dell recommends that if core_pattern on the client is set by NAT to a specific directory, then the diagnostics script has to look into that directory for any related cores. NetBackup on Windows Media Servers For NetBackup running on a Windows media server, Dell recommends gathering the following files: • RDA with OST plug-in configuration files and log files from the media server: – • Location: %ALLUSERSPROFILE%\Dell\OST\log\libstspiDell.
d. 140 Retrieve the dump file from the location specified in the dialog that displays after the dump file is created.
Configuring and Using VTL 12 This topic introduces Virtual Tape Libraries (VTLs) and related concepts and tasks. Refer to the subsequent topics and procedures in this section for more information. Understanding VTL A Virtual Tape Library (VTL) is an emulation of a physical tape library on a disk-based deduplication and compression system such as the DR Series system.
NDMP The Network Data Management protocol (NDMP) is used to control data backup and recovery between primary and secondary storage in a network environment. For example, a NAS server (Filer) can talk to a tape drive for the purposes of a backup. You can use the protocol with a centralized data management application (DMA) to back up data on file servers running on different platforms to tape drives or tape libraries located elsewhere within the network.
NOTE: For more information about using the CLI, see the Dell DR Series CLI Reference Guide. A library can only contain tapes of the same size. For example, if the library is originally created with 10 tapes of size 10GiB, additional tapes of size 10GiB can only be added.
Refer to the topics, Creating Storage Containers and Creating a VTL Type Container, for detailed instructions about creating containers. Refer to the Dell DR Series System Command Line Interface Guide for details about the CLI commands for creating containers. Authentication/User Management Considerations • You can use the following commands to view user information and manage passwords for the iSCSI user: iscsi_user, and NDMP user: ndmp_user.
Configuring and Using Encryption at Rest 13 This chapter introduces the concept of Encryption at Rest as used by the DR Series system as well as related concepts and tasks. Refer to the subsequent topics for more information. Understanding Encryption at Rest Data that resides in the DR Series system can be encrypted.
Term Description days. This rotation period is user-configurable and can be specified in days. Encryption at Rest and DR Series Considerations This topic describes key features and considerations of using Encryption at Rest in the DR Series system. • Key Management — In internal mode there is a maximum limit of 1023 keys. By default when encryption is enabled on the system, the key rotation period is set to 30 days.
3. Encryption process. After encryption is enabled, the data on the DR Series system that gets backed up is encrypted and is kept encrypted until it is expired and cleaned by the system cleaner. Note that the encryption process is irreversible. 4. Encryption of pre-existing data. Any pre-existing data on a DR Series system will also be encrypted using the currently set mode of key management. This encryption occurs as part of the system cleaner process.
Troubleshooting and Maintenance 14 This topic provides an overview of the basic troubleshooting and maintenance information that is available to help you better understand the current state of your DR Series system.
There are still other alert and event messages that direct you to contact Dell Support for assistance, where Dell Support intervention may be required. • Table 1 lists the DR Series System Alert Messages by system alert type: general system, system chassis, NVRAM, and PERC-specific alert messages that could be displayed during the course of backup and deduplication-related operations.
Alert Message Description/Meaning or Action NVRAM does not match the data volume. If this is a newly replaced NVRAM, use the maintenance -hardware --reinit_nvram command to reinitialize the NVRAM. For more information, see the Dell DR Series System Command Line Reference Guide. Storage usage is approaching the system capacity. Clean up the filesystem. If issue persists, contact Dell Support for possible assistance or intervention. Replication re-sync cannot proceed.
Alert Message Description/Meaning or Action Fan failed. • • Verify that the designated cooling fan is present and is installed correctly. Verify that the designated cooling fan spins up and runs. If this does not resolve the issue, replace the designated cooling fan. Fan is missing. Attach or replace the designated missing cooling fan. Abnormal network errors detected on Network Interface Controller .
Alert Message Description/Meaning or Action Voltage probes have recorded readings in the failed range. • • Check the Events page in the DR Series system for specific voltage events and the location of the voltage probes. Check the power supplies. If there are no issues with the power supplies, have a service technician check the DR Series system appliance to see if it requires any servicing. Storage Controller failed. Replace the RAID controller in the DR Series system.
Alert Message Description/Meaning or Action Virtual Disk failed. Replace any failed or missing physical disk(s) and run the Dell Restore Manager (RM) utility. Virtual Disk has an invalid layout. Run the Dell Restore Manager (RM) utility to repair this installation. Virtual Disk Virtual Disk redundancy is degraded. Replace the physical disk(s) with a supported SAS Dell physical disk(s). One or more physical disks have failed and therefore Virtual disk redundancy is degraded.
Alert Message Description/Meaning or Action The storage appliance failed to gather the system diagnostics. • Storage Appliance Critical Error: BIOS System ID is incorrect for correct operation of this storage appliance. • • Resolve all issues in the DR Series system diagnostics log bundle. Re-attempt to collect the diagnostics log bundle. Contact Dell Support for assistance. • • The DR Series system appliance requires service. Contact Dell Support for assistance.
System Event Message Description/Meaning or Action HTTP Service failed. Web services will be unavailable. HTTP Service started. Informational message. No user intervention is required. HTTP Service is available now. Informational message. No user intervention is required. Diagnostics collection service failed. Diagnostic collection service started. Informational message. No user intervention is required. Diagnostics collection service re-started. Informational message.
System Event Message Description/Meaning or Action Windows Active Directory client module failed to start. Active Directory support will not be available. Windows Active Directory client module started. Informational message. No user intervention is required. Windows Server module started. Informational message. No user intervention is required. Windows Server module re-started. Informational message. No user intervention is required. Windows Server module is down.
System Event Message Description/Meaning or Action iSCSI server started. Informational message. No user intervention is required. iSCSI server re-started. Informational message. No user intervention is required. iSCSI server is not healthy. iSCSI server is crashing repeatedly. Contact Dell Support. NDMP tape server started. Informational message. No user intervention is required. NDMP tape server re-started. Informational message. No user intervention is required.
System Event Message Description/Meaning or Action NVRAM does not match the data volume. If this is a newly replaced NVRAM, use "maintenance -hardware --reinit_nvram" to initialize. Software upgrade is in progress. Informational message. No user intervention is required. Upgrade did not complete. Retry upgrade after rebooting the appliance. Upgrade completed successfully. Reboot required. Reboot the system. Upgrade completed successfully. System coming online. Informational message.
System Event Message Description/Meaning or Action A high-temperature reading has been detected on the NVRAM PCI controller. System will not become operational until the temperature reduces to an ambient value of 55 degrees Celsius (131 degrees Fahrenheit). Informational message. No user intervention is required. If issue persists, contact Dell Support for assistance or intervention. The next NVRAM capacitor health check is scheduled for . Informational message.
System Event Message Description/Meaning or Action BIOS System ID is incorrect for correct operation of this storage appliance. The storage appliance requires service. System clock has drifted more than 24 hours, from the last filesystem start. Please check your clock settings and reboot. This DR4x00 Virtual Machine usage time limit has expired. Please contact your DR4x00 Sales representative to get the Hardware Version. This DR4x00 Virtual Machine is for evaluation purpose only.
System Event Message Description/Meaning or Action NVRAM has failed to backup/restore data during last boot. Contact Dell Support. NVRAM hardware failure. Contact Dell Support. Data volume is not present. Check that all drives are inserted and powered up. Contact Dell Support for assistance or intervention. Filesystem server failed to start after multiple attempts. Contact Dell Support for assistance or intervention. Filesystem server crashed multiple times. System is now entering Maintenance mode.
System Event Message Description/Meaning or Action Datacheck detected potential corrupt lsu info. Run filesystem scan as soon as possible. ("maintenance -filesystem --start_scan verify_rda_metadata") Temperature warning detected on NVRAM PCI controller. Please check the data center air conditioning, rack ventilation, and internal cooling fans for any issues. Ensure that there is proper air flow through the system appliance, and clean the system cooling vents as needed.
System Event Message Description/Meaning or Action Seeding cannot contact the target device. Check to make sure that the target device is available and write-enabled. Then remove and re-add the target device. Seeding process complete. Informational message. No user intervention is required. System has reached space full condition, seeding will be stopped. Informational message. No user intervention is required. Seeding failed to create Zero log entries.
System Event Message Description/Meaning or Action Container is configured to access over by the following clients: ('*' means access for everyone). Informational message. No user intervention is required. Container is updated to access over by the following clients: ('*' means access for everyone). Informational message. No user intervention is required. Disabled access for Container over Informational message.
System Event Message Description/Meaning or Action Snapshot → successfully updated. Informational message. No user intervention is required. Snapshot → successfully deleted. Informational message. No user intervention is required. Client authorized to access NDMP Tape Server. Informational message. No user intervention is required. Successfully updated NDMP to use port . Informational message. No user intervention is required.
System Event Message Description/Meaning or Action System is entering Maintenance mode. Informational message. No user intervention is required. Contact Dell Support for assistance or intervention. System entering Support Mode. Contact Dell Support for assistance or intervention. Internal failure—OFS client initialization failure. Contact Dell Support for assistance or intervention. Internal failure—mtab initialization failure for container .
System Event Message Description/Meaning or Action Filesystem has reached the maximum supported number of Name Space entries. Please clean up the filesystem to allow new file and directory create operations. If this condition persists, contact Dell Support for assistance or intervention. Filesystem has recovered from a lack of available Name Space entries. Filesystem create operations will now be allowed. Contact Dell Support for assistance or intervention.
System Event Message Description/Meaning or Action issue persists, contact Dell Support for assistance or intervention. Replication switching to re-sync due to corrupt replication Name Space oplog for container . Replication data operations log (oplog) full for container . The DR Series system should self-correct itself. If condition persists, reduce number of inodes, or contact Dell Support for assistance or intervention.
System Event Message Description/Meaning or Action Replication failed for container error . Collect a diagnostics log file bundle, and open a Support record with Dell Support for assistance. Replication server failed to commit blockmap for The DR Series system should self-correct itself. If condition container . System is entering Maintenance persists, reduce number of inodes, or contact Dell Support for mode. assistance or intervention.
System Event Message Description/Meaning or Action Storage usage approaching system capacity. Informational message. No user intervention is required. Online data verification (DataCheck) started. Informational message. If issue persists, contact Dell Support for assistance or intervention. Online data verification (DataCheck) suspended. Informational message. If issue persists, contact Dell Support for assistance or intervention. Online data verification (DataCheck) stopped. Informational message.
System Event Message Description/Meaning or Action Container added to seeding. Informational message. No user intervention is required. Container is removed while seeding is in progress. Informational message. No user intervention is required. Container removed from seeding. Informational message. No user intervention is required. Seeding job created. Informational message. No user intervention is required. Seeding job deleted. Informational message.
System Event Message Description/Meaning or Action Internal Error. Datastore length mismatch . Maintenance-based issue with the DR Series system. Check status using Maintenance mode or DR Series system CLI commands. Contact Dell Support as needed. Data volume capacity threshold reached. Informational message. No user intervention is required. Out of space. Rollback of updates on object Maintenance-based issue with the DR Series system. Check failed.
System Event Message Description/Meaning or Action Internal Error. Memory allocation failure. Collect diagnostics log file bundle. Background compression started. Informational message. No user intervention is required. Background compression completed. Informational message. No user intervention is required. Optimization initialized on container . Informational message. No user intervention is required. Optimization terminated on container . Informational message.
System Event Message Description/Meaning or Action NTP service disabled. Informational message. No user intervention is required. User data destroyed using CLI command. Informational message. No user intervention is required. User enabled. Informational message. No user intervention is required. User disabled. Informational message. No user intervention is required. Networking interfaces restarted. Informational message. No user intervention is required.
System Event Message Description/Meaning or Action User logged into the system. Informational message. No user intervention is required. CIFS user added. Informational message. No user intervention is required. CIFS user deleted. Informational message. No user intervention is required. Password changed for CIFS user . Informational message. No user intervention is required. System upgrade completed . Informational message.
System Event Message Description/Meaning or Action One (or more) file(s) were deleted as part of the repair process. Informational message. No user intervention is required. To verify, please use the DR Series system CLI maintenance -filesystem --repair_history verbose command. One or more file(s) were deleted as part of the repair process for container . Replication will be stopped for this container. Informational message. No user intervention is required.
System Event Message Description/Meaning or Action System is entering the Maintenance mode: RDA meta directory is corrupted. Informational message. No user intervention is required. RDA server initialization failed. Informational message. No user intervention is required. RDA server initialization was successful. Informational message. No user intervention is required. System entering Maintenance Mode - RDA txlog full, LSU . Informational message. No user intervention is required.
collect --dset). For more information about DR Series system command line interface commands, see the Dell DR Series Command Line Reference Guide. The DSET-based information that gets collected for the system helps Dell Support to troubleshoot or evaluate the status of your DR Series system.
• Maintenance Mode Progress bar: – Displays the five stages of Maintenance mode – Updates the progress bar as each stage completes NOTE: If an alert displays above the Maintenance Mode progress bar, this indicates that the filesystem check has completed, and it has generated a report on the repairable files (which are displayed in the Repair Report pane under the Maintenance Mode progress bar). To repair all of the reported files listed in the Repair Report, you must click Confirm Repair Filesystem.
NOTE: When in Maintenance mode, image expiration fails because the DR Series system is in a read-only state. If this occurs, the DMA assumes that the backup images have expired. However, the DR Series system administrator may be unaware that the backup data images still reside on the DR Series system.
NOTE: The Cleaner Schedule page displays the current DR Series system time zone and current timestamp (using this format: US/Pacific, Fri Nov 2 15:15:10 2012). To schedule Cleaner operations on your system, complete the following: 1. Select Schedules → Cleaner Schedule. The Cleaner Schedule page is displayed. 2. Click Schedule to create a new schedule (or click Edit Schedule to modify an existing schedule). The Set Cleaner Schedule page is displayed. 3.
• Current Run Phase 1 Records Processed (lists the number of data records processed in current Cleaner process phase 1) • Current Run Phase 1 End Time (indicates date and time for end of current Cleaner process phase 1) • Current Run Phase 2 Start Time (indicates date and time for start of current Cleaner process phase 2) • Current Run Phase 2 Records Processed (lists the number of data records processed in current Cleaner process phase 2) • Current Run Phase 2 End Time (indicates date and time for
Supported Ports in a DR Series System 15 The following table lists the application and service ports found on a normally operating DR Series system. There may be other ports that are not listed here, that an administrator may need to open and enable to support specific operations across the network. Be aware that the ports listed in the following table may not reflect your specific network environment, or any planned deployment.
Port Type Number Port Usage or Description TCP 199 SNMP daemon—used by Simple Network Management Protocol (SNMP) requests TCP 801 NFS status daemon 184
Getting Help 16 For more information about what you can attempt to resolve yourself or to get technical assistance from Dell for the DR Series system, see the topics below, “Before Contacting Dell Support,” and “Contacting Dell.
NOTE: If you do not have an active Internet connection, you can still find the proper contact information that you need on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be available in your area. To contact Dell for sales support, technical support, or customer service issues: 1. Visit support.dell.com. 2.