Dell DR Series System Administrator Guide
주, 주의 및 경고 노트: "주"는 컴퓨터를 보다 효율적으로 사용하는 데 도움을 주는 중요 정보를 제공합니다. 주의: "주의"는 하드웨어 손상이나 데이터 손실의 가능성을 설명하며, 이러한 문제를 방지할 수 있는 방법을 알려줍니다. 경고: "경고"는 재산상의 피해나 심각한 부상 또는 사망을 유발할 수 있는 위험이 있음을 알려줍니다. © 2013 Dell Inc. 본 설명서에 사용된 상표인 Dell™, Dell 로고, Dell Boomi™, Dell Precision™, OptiPlex™, Latitude™, PowerEdge™, PowerVault™, PowerConnect™, OpenManage,™ EqualLogic™, Compellent™, KACE™, FlexAddress™, Force10™ 및 Vostro™는 Dell Inc.의 상표입니 다.
목차 1 DR Series 시스템 소개..............................................................................................................9 DR Series 시스템 GUI 설명서 정보........................................................................................................................ 9 What's New In This Release.................................................................................................................................... 9 기타 필요한 정보..............................................................
Interacting With the DR Series System.................................................................................................................. 33 Networking Preparations for the DR Series System........................................................................................33 Connections for Initializing a DR Series System.....................................................................................................34 DR Series 시스템 초기화..................................................
DR Series 시스템 암호 관리................................................................................................................................. 73 Modifying the System Password......................................................................................................................73 Resetting the Default System Password..........................................................................................................73 DR Series 시스템 종료................................................
DR Series 시스템 모니터링...................................................................................................99 Monitoring Operations Using the Dashboard Page................................................................................................99 시스템 상태 표시줄........................................................................................................................................99 DR Series 시스템과 용량, 스토리지 저장량, 처리량 창..............................................................
DR Series 시스템: 올바른 종료 및 시작......................................................................................................120 DR Series 시스템 및 NVRAM:.......................................................................................................................121 8 OST 구성 및 사용...................................................................................................................123 OST 이해................................................................................................
Linux용 OST 플러그인 로그 회전................................................................................................................ 141 매체 서버 정보 수집 지침.................................................................................................................................. 141 Linux 매체 서버의 NetBackup...................................................................................................................... 142 Windows 매체 서버의 NetBackup........................................................
DR Series 시스템 소개 1 DR Series 시스템 문서에는 Dell DR Series 시스템을 사용하여 데이터 스토리지 작업을 수행하고 스토리지 및 복 제 컨테이너를 관리하는 방법을 설명하는 주제가 있습니다. DR Series 시스템 주제에서는 백업 및 복제 작업을 관리하는 데 사용할 수 있는 DR Series 시스템 그래픽 사용자 인터페이스(GUI)를 소개하고 설명합니다. 포괄적인 GUI 기반 절차에 따라 지원되는 웹 브라우저에서 모든 관리 기능에 액세스할 수 있습니다. 이 안내서는 중요한 관리 작업이 DR Series 시스템 GUI에서 지원되지 않을 경우에 활용할 수 있도록 해당 명령행 인터페이스(CLI) 명 령을 제공하고 설명합니다. DR Series 시스템 CLI 명령에 대한 자세한 내용은 Dell DR Series 시스템 명령행 참조 안내서를 참조하십시오.
노트: The maintenance mode User interface for the DR Series systems is updated in this release. 기타 필요한 정보 경고: 시스템과 함께 제공되는 안전 및 규정 정보를 참조하십시오. 보증 정보는 이 문서 안에 포함되어 있거 나 별도의 문서로 제공될 수 있습니다. • Dell DR Series 시스템 소유자 매뉴얼은 솔루션 기능에 대한 정보를 제공하고 DR Series 시스템 구성요소 를 설치하거나 교체하는 방법에 대해 설명합니다. 이 문서는 support.dell.com/manuals에서 볼 수 있습니 다. • Dell DR Series 시스템 명령행 참조 안내서는 DR Series 시스템 명령행 인터페이스(CLI)를 사용하여 DR Series 시스템 데이터 백업 및 복제 작업 관리에 대한 정보를 제공합니다. 이 문서는 support.dell.com/ manuals에서 볼 수 있습니다.
Understanding the DR Series System 2 The DR Series system is a high-performance, disk-based backup and recovery appliance that is simple to deploy and manage, and offers unsurpassed Total Cost of Ownership benefits. Features such as innovative firmware and an allinclusive licensing model ensure optimal functionality and the assurance of no hidden costs for desired future features.
• Wide variety of data backup installations and environments The Dell DR Series system contains data backup and management software preinstalled on a Dell hardware appliance, which provides you with a robust disk-based data backup capability installed on a deduplication-enabled appliance.
내부 드라이브 용량 표 1에 나열된 용량 값은 DR4000/DR4100 시스템 릴리스에서 관련 오버헤드에 맞게 조정된 내부 드라이브 및 사용 가능한 실제 용량을 나타냅니다. 노트: 표 1에서 TB 및 GB는 각각 10진수 값의 테라바이트와 기가바이트를 나타내며 TiB는 2진수 값의 테비 바이트를 나타냅니다. 테비바이트는 표준 기반의 다중 2진 바이트로서 디지털 정보 스토리지의 단위입니 다. 표 1. 내부 드라이브 용량 및 사용 가능한 실제 용량 DR Series 시스템 드라이브 용량 사용 가능한 실제 용량(10진수) 사용 가능한 실제 용량(2진수) 3 TB (DR4100 시스템에만 해당) 26.79 TB 23.8 TiB 2 TB 17.9 TB 15.9 TiB 1 TB 8.89 TB 7.9 TiB 600 GB 5.29 TB 4.6 TiB 300 GB 2.47 TB 2.
Whenever a document is repeatedly backed up, the 0s and 1s stay the same because the file is simply being duplicated. The similarities between two files can be easily identified using block deduplication because the sequence of their 0s and 1s remain exactly the same. In contrast to this, there are differences in online data. Online data has few exact duplicates. Instead, online data files include files that may contain a lot of similarities between each file.
노트: Starting with Release 2.0, the DR Series system software includes version checking that limits replication only between other DR Series systems that run the same system software release version (DR Series systems running Release 2.0.x software can only replicate with other DR Series systems that run the same release system software). For example, Release 2.0.x systems will not be able to replicate with Release 2.1 or Release 3.0 systems, but can replicate with systems running Release 2.0.0.1 or 2.0.0.2.
from the tape backup to the original location; first, restore the data back to a DR Series system replica container, and then restore it back to the original source location of the data on the other side of the WAN link. 노트: If you choose to use this alternate workaround method, you must set up a new data storage unit in the DMA and import the images before a restore to the original location can occur.
Using its deduplication and compression technology, DR Series systems can help achieve an expected data reduction ratio of 15:1. Achieving this reduction in data means that you need fewer incremental storage operations to run and it provides you with a smaller backup footprint. By removing redundant data, DR Series systems deliver fast reliable backup and restore functionality, reduce media usage and power and cooling requirements, and improve your overall data protection and retention costs.
When this type of relationship exists between distinct containers on two distinct DR Series systems, it can be considered bidirectional in the sense that: • The West1 container on the acme-west source system can replicate data to a separate East1 container on the acme-east target system. • The East2 container on the target acme-east system can also replicate data back to the West2 container on the source acme-west system.
이 상황에서, 복원되는 데이터의 일부가 WAN 링크를 통해 전송됩니다. 그러면 원격 복원 속도가 현저히 빨라질 수 있습니다. 하지만 몇 가지 문제점도 있습니다. • 1단계를 제대로 따르지 않으면 완전하게 복제되지 않은 모든 변경사항이 유실됩니다. • 2단계와 3단계에서, 원래 DR Series 시스템 소스 컨테이너에 작성되는 모든 데이터가 유실될 수 있습니 다. • 4단계에서, 전환이 이루어지기 전에 완전하게 다시 복제되지 않은 데이터가 유실될 수 있습니다. 다음을 수행하여 이러한 문제를 해결할 수도 있습니다. 1. 대상 DR Series 시스템에 새 컨테이너를 만듭니다. 2. 이 컨테이너에서 소스 DR Series 시스템 컨테이너로의 복제를 설정합니다. 3. DMA에 새 디스크 스토리지 단위를 설정하고 DMA에서 새 이미지를 인식하는지 확인합니다. 4. 대상 DR Series 시스템(원래 소스 위치)에서 DMA로 이전 이미지를 다시 가져옵니다. 5.
NFS는 클라이언트가 로컬 시스템에서와 같이 원격 시스템에서 파일을 보고, 저장하며, 업데이트할 수 있는 클라 이언트측 응용프로그램입니다. 시스템 또는 네트워크 관리자는 파일 시스템의 모든 부분을 장착할 수 있으며 각 파일에 할당된 권한을 통해 장착된 파일 시스템(또는 파일 시스템 부분)에 액세스할 수 있습니다. NFS 프로토콜 은 Unix, Macintosh, OpenVMS 및 Microsoft Windows 운영 체제를 지원합니다. CIFS CIFS(Common Internet File System) 원격 파일 액세스 프로토콜은 DR Series 시스템에서 지원되며 SMB(Server Message Block)라고도 합니다. SMB는 Microsoft Windows 운영 체제를 실행하는 시스템의 NFS(Network File System) 프로토콜보다 더 일반적으로 사용됩니다. CIFS를 통해 프로그램이 원격 컴퓨터에서 파일이나 서비스를 요청할 수 있습니다.
노트: Any user that is part of BUILTIN\Administrators can edit ACLs on CIFS shares. The local DR Series system administrator is included in the BUILTIN\Administrators group. To add additional domain groups to the BUILTIN \Administrators group, you can use the Computer Manager tool on a Windows client to connect to the DR Series system as Domain administrator and add any groups you want. This capability allows users other than the Domain administrator to modify an ACL as needed. • • • • • • • BUILTIN\Ad
릴리스 1.1 이전에 생성된 기존 컨테이너의 경우, 지정된 DR Series 시스템에 로그인하는 모든 사용자가 모든 파 일에 액세스할 수 있습니다. 1.1 이전 릴리스 컨테이너에 있는 연관된 ACL은 다음과 같은 권한만 지원합니다. • • 모든 사용자: – 허용되는 작업: 전체 액세스 – 적용 대상: 이 폴더, 하위 폴더 및 파일 BUILTIN\관리자: – 허용되는 작업: 전체 액세스, 개체 상속, 컨테이너 상속 – 적용 대상: 이 폴더, 하위 폴더 및 파일 하지만 기존 컨테이너에 고유한 ACL을 적용할 수도 있습니다. 지정된 컨테이너의 공유 루트를 탐색하고 디렉터 리 트리의 ACL을 따르면 됩니다. 이 작업을 완료하는 데 필요한 시간은 컨테이너에 상주하는 파일 및 폴더 수에 따라 다릅니다. 로컬 사용자를 생성하면 BUILTIN\사용자에 추가됩니다. 관리자 계정은 BUILTIN\관리자의 구성원이므로 컨테이 너의 ACL에 문제가 발생할 경우(예: ACL이 적용된 후 해당 관리자 또는 도메
Technology File System)에서는 ACL을 보안 설명자(SD) 프로세스의 일부로 사용하므로 파일 시스템 개체를 파일 및 디렉터리로 액세스하기 위한 권한이 필요합니다. ACL에서는 다음과 같은 두 가지 유형의 사용자가 지원됩니 다. • 소유자 • 그룹 소유자와 그룹에는 개체 소유자 또는 개체를 소유하고 있는 그룹을 정의하고 식별하는 보안 ID(SID)가 있습니다. ACL의 ACE는 액세스를 허용하거나 정의하고 적용되는 상속 설정을 정의하는 특정 권한인 SID로 구성됩니다. • IO - 상속만: 액세스 확인에 사용되지 않음 • OI - 개체 상속: 새 파일에 이 ACE가 추가됨 • CI - 컨테이너 상속: 새 디렉터리에 이 ACE가 추가됨 Windows NTFS ACL에는 다음과 같은 읽기, 쓰기, 추가, 실행, 삭제 권한이 포함되어 있습니다.
be transferred to the system. This process provides two benefits: it improves the overall backup speed, and also reduces the network load.
– 파일 복사 또는 복제 • NetBackup이 OST API를 사용하여 저장된 파일이 DR Series 시스템에서 만료되도록 하는 경우 파일 시스 템에서 파일을 삭제합니다. • 마찬가지로, NetBackup이 OST API를 사용하여 저장된 파일에서 복원하려는 경우 복원할 파일을 DR Series 시스템에 알려주고 복원할 수 있도록 저장된 파일을 NetBackup에 전달하도록 지시합니다. 노트: OST에는 최적화된 중복이라고 하는 기능이 있습니다. 예를 들어, 최적화된 중복에서 DMA(NetBackup) 는 장치 A가 장치 B에서 최적화된 중복을 수행하도록 지시합니다. 장치 A와 B는 상호 통신하여 장치 B에 사 용하기 위해 A에서 B로 복제해야 할 파일의 데이터 세그먼트를 결정하여 장치 B에 완전한 전체 중복 데이 터 파일이 포함되도록 합니다. 이 작업에 성공하면, DMA는 이 데이터 파일의 두 사본을 인식하게 되어 장치 B에 상주하는 다른 데이터 파일처럼 이 파일을 사용할 수 있습니다.
• Backup, restore, and optimized duplication operations need to be performed via the OST plug-in • Optimal supported aggregated throughput rates: – 3 Terabytes per hour (TB/hr) for passthrough write operations – 4 TB/hr for optimized write operations 노트: Passthrough writes are when data is sent from a media server to the DR Series system without applying any optimization to the data.
• DR4100 system: This consists of preinstalled DR4000 system software on a Dell PowerEdge R720xd appliance platform. The DR Series system consists of a total of 14 drives. Two of these drives are 2.5-inch drives that are configured as a Redundant Array of Independent Disks (RAID) 1 on the RAID Controller and this is considered to be volume 1. In the DR4000 system, these drives are internal, while in the DR4100 system, these drives are accessible from the rear.
노트: If you are running a DR4000 system with an installed release of system software prior to 2.1, and you intend to upgrade to release 2.1 system software and install an external expansion shelf (or shelves), Dell recommends that you observe the following best practice sequence of operations to avoid any issues: • Upgrade the DR4000 system with the release 2.1 system software • Power off the DR4000 system (required for 2.1 with Dell OpenManage 7.
• Hardware • – BIOS – RAID controllers – Hard drives (internal) – Hard drives (external) – USB flash drives – Network interface controllers – iDRAC Enterprise – Marvell WAM controller Software – – – – – – – Operating System Supported backup software Network file protocols and backup client operating systems Supported web browsers Supported system limits Supported OST software and components Supported RDS software and components Terminal Emulation Applications To access the DR Series system command line
rear chassis on the first enclosure. This is considered a redundant mode connection via the SAS In/Out connectors on the enclosures with the DR Series system appliance. If you install a second enclosure and cable it as described here, make sure to set the enclosure mode switch on the MD1200 front chassis to the top (unified mode) positions. For more information, see Dell PowerVault MD1200 and MD1220 Storage Enclosures Hardware Owner's Manual at support.dell.com/manuals. 그림 3 .
그림 5 . SAS Port and Cable Connections (Dell PowerVault MD1200 EMM) 1. SAS cable 2. pull-tab DR Series 시스템 확장 선반 추가 DR Series 시스템에서 확장 선반 인클로저 구성과 연관된 세 가지 작업이 있습니다. 이러한 작업을 수행해야 추 가적인 데이터 스토리지 용량을 사용할 수 있습니다. • DR Series 시스템에 확장 선반 인클로저를 연결하는 모든 케이블을 설치합니다(자세한 내용은 DR Series 시스템 - 확장 선반 케이블 연결 참조). • Storage(스토리지) 페이지를 사용하여 확장 선반 인클로저를 추가하고 활성화합니다(이 주제에 설명되 어 있음). • 확장 선반 인클로저의 Dell 라이센스를 설치합니다(자세한 내용은 확장 선반 라이센스 추가 참조). DR Series 시스템에 확장 선반 인클로저를 추가하려면 다음을 수행합니다. 1. 탐색 패널에서 Storage(스토리지)를 클릭합니다.
5. 인클로저가 추가되었는지 확인하려면 Dashboard(대시보드)→ Health(상태)를 클릭합니다. Health(상태) 페이지가 표시되고, 올바르게 케이블 연결되어 활성화된 각 확장 선반 인클로저의 해당 탭에 녹색 상태 확인 표시가 나타납니다. 예를 들어, 2개의 인클로저를 설치하면 Enclosure 1(인클로저 1) 탭과 Enclosure 2(인클로저 2) 탭이 표시됩니다. 노트: Enclosure(인클로저) 탭에 녹색 상태 확인 표시가 나타나지 않으면 인클로저에 문제가 있는 것입 니다(예: 올바르게 연결 또는 활성화되지 않음). 6. 확장 선반 인클로저를 추가한 후에는 확장 선반 라이센스를 추가해야 합니다. 자세한 내용은 확장 선반 라이센스 추가를 참조하십시오.
Setting Up the DR Series System 3 Before you can interact with the DR Series system using one of its two supported methods: the web-based DR Series system graphical user interface (GUI) using a web browser or the command line interface (CLI) and a terminal emulator application (for example, PuTTY), you must first ensure that it is properly set up. For more information about properly setting up the DR Series system, see the following links.
To perform an initial configuration, you need: • – An IP address for the system – A subnet mask address – A default gateway address – A DNS suffix address – A primary DNS server IP address – (Optional) A secondary DNS server IP address NIC Connections: To configure NIC connection bonding remember that, by default, the DR Series system will configure its NIC interfaces together as a bonded team (and only one IP address is needed because the bonded NICs assume the primary interface address).
DR Series 시스템 초기화 DR Series 시스템 그래픽 사용자 인터페이스(GUI)를 처음으로 사용하려는 경우 시스템을 올바르게 초기화해야 합니다. DR Series 시스템을 초기화하려면 다음을 수행합니다. 1. 로컬 콘솔 KVM(키보드-비디오 모니터) 연결 또는 iDRAC 연결을 사용하여 DR Series 시스템 CLI에 로그인합 니다. 자세한 내용은 로컬 콘솔 연결 또는 iDRAC 연결을 참조하십시오. 2. Initial System Configuration Wizard(초기 시스템 구성 마법사)를 사용하여 시스템 네트워크 설정을 구성합니 다. 자세한 내용은 DR Series 시스템에 로그인 및 초기화를 참조하십시오. 초기 시스템 구성 마법사를 사용하면 다음과 같은 네트워크 설정을 구성하여 시스템의 최초 초기화를 완료할 수 있습니다.
알려진 정적 IP 주소를 사용하고 있는 경우 초기 시스템 구성 마법사 실행을 건너뛰고 해당 사용자 인터페이스 를 사용하여 DR Series 시스템을 직접 구성할 수 있습니다. DR Series 시스템을 구성하려면 System Configuration(시스템 구성) → Networking(네트워킹) 을 선택하고 원하는 네트워킹 설정을 구성합니다. 자세한 내용은 네트워킹 설정 구성을 참조하십시오. 노트: 로그인 및 초기 시스템 구성 마법사 사용에 대한 자세한 내용은 네트워킹 설정 구성을 참조하십시오.
노트: The DR4000 system supports up to four 1–GbE ports or up to two 10–GbE ports; for the 1–GbE ports, these are two internal LAN on Motherboard (LOM) ports referenced in item 4 above that reside on the motherboard, and two ports on an expansion card referenced in item 5 above. If the DR4000 system is using the two 10–GbE ports, these reside on an expansion card referenced in item 5 above. 5. (DR4100 system appliance) Locate the VGA monitor port and the USB ports on the back of your system.
iDRAC Connection The iDRAC connection requires a network connection between the integrated Dell Remote Access Control (iDRAC) management port on the DR Series system and another computer running the iDRAC remote console session in a supported browser. The iDRAC provides remote console redirection, power control, and the out-of-band (OOB) system management functions for the DR Series system. iDRAC connections are configured using console redirection and the iDRAC6/7 web interface.
7. To configure a default gateway address, type the default gateway address you want to use (for example, 10.10.20.10), and press . 8. To configure a DNS Suffix, type the DNS suffix you want to use (for example, storage.local), and press . 9. To configure a primary DNS server IP address, type an IP address you want to use for the primary DNS server (for example, 10.10.10.10), and press . 10.
노트: This procedure describes the logging in process from a first-time perspective, starting with the Customer Registration and Notification page, the completion of the Initial System Configuration Wizard process, and the Initial Software Upgrade page. 1. In a supported web browser, type the IP address or hostname of the system in the browser Address bar, and press . The DR Series System Login page is displayed.
b) In New Password, enter the new administrator password. c) In Retype New Password, enter the new administrator password again to confirm it. d) Click Next to continue with the initial configuration process (or click Back to return to the previous page, or click Exit to close the Initial System Configuration Wizard). The Initial Configuration — Networking page is displayed. 6.
– System Status bar – System Information pane – Command bar 노트: Located on the DR Series System Dashboard page command bar, you can display the Help system documentation by clicking Help, or logout of the system by clicking Log out. 노트: When logged in, a Logout Confirmation dialog is displayed after 45 minutes of non-use. This dialog displays for 30 seconds before the DR Series system performs a forced timeout. Click Continue to reset the 45-minute logout timer.
7. Click Confirm for the DR Series system to accept your values (or click Skip) to proceed to the Initial System Configuration Wizard page. Windows IE 브라우저에서 액티브 스크립팅 활성화 Microsoft Windows Internet Explorer(IE) 웹 브라우저에서 액티브 스크립팅(JavaScript)을 활성화하려면 다음을 완 료합니다. 노트: 이 절차에서는 액티브 스크립팅(JavaScript)을 활성화하도록 Windows IE 웹 브라우저를 구성하는 방 법에 대해 설명합니다. Windows 기반 서버에서 이 설정이 기본적으로 비활성화되는 경우가 많습니다. 1. IE 웹 브라우저를 실행하고 Tools(도구)→ Internet Options(인터넷 옵션)를 클릭합니다. Internet Options(인터넷 옵션) 페이지가 표시됩니다. 2.
– 경고 수 – 이벤트 수 • 용량 • 스토리지 저장량 • 처리량 • 시스템 정보 노트: Storage Savings(스토리지 저장량) 및 Throughput(처리량)에 나열되는 값을 새로 고치려면 합니다. 을 클릭 노트: DR Series 시스템 탐색 패널에서, Dashboard(대시보드) 섹션은 다음과 같은 메뉴 옵션으로 구성되어 있으며 옵션을 선택하면 해당 페이지가 표시됩니다. • Alerts(경고) • Events(이벤트) • Health(상태) • Usage(사용량) • Statistics: Container(통계: 컨테이너) • Statistics: Replication(통계: 복제) 자세한 내용은 다음 절을 참조하십시오.
이벤트 DR Series 시스템은 Events(이벤트) 페이지에 현재 시스템 이벤트를 표시하는 두 가지 방법을 제공합니다. • Dashboard(대시보드)→ Events(이벤트)를 클릭합니다. • Dashboard(대시보드) 페이지에서 Number of Events(이벤트 수) 링크를 클릭합니다. Events(이벤트) 페이지는 Event Filter(이벤트 필터) 창을 제공합니다. 이 창에서는 선택한 이벤트 심각도, 시작 및 종료 날짜 설정값에 따라 특정 검색 기준을 설정할 수 있습니다. 검색 기준을 설정한 후에 Start Filter(필터 시작) 를 클릭하여 값과 일치하는 이벤트를 표시합니다. 일치하는 이벤트가 이벤트 요약 표에 표시됩니다. 이 표에는 정의한 검색 기준과 일치하는 총 시스템 이벤트 수 를 나열하며 다음과 같은 기준에 따라 일치하는 각 시스템 이벤트를 정의합니다.
상태 페이지: DR4000 시스템 그림 1 상태 페이지(DR4000 시스템 및 구성요소) 상태 페이지: DR4100 시스템 그림 2 상태 페이지(DR4100 시스템 및 구성요소) 기본적으로, System(시스템) 탭이 먼저 표시되고 각 하드웨어 구성요소에 대해 다음과 같은 속성이 나열됩니다. DR Series 시스템 구성요소 Health(상태) 페이지의 System(시스템) 탭에서, 다음과 같은 이미지 및 시스템 하드웨어 상태 표에 시스템 구성요 소의 상태가 표시됩니다(특정 위치는 그림 1과 2 참조).
• 시스템 하드웨어 상태(표) - 어플라이언스의 모든 주요 하드웨어 하위 구성요소의 현재 상태 표시 – 전원 공급 장치 - 상태, 이름 및 위치 – 팬 - 상태, 이름, 속도 및 식별자 – 온도 - 상태, 이름 및 온도 – 스토리지 - 스토리지 컨트롤러, 스토리지 가상 디스크, 스토리지 실제 디스크, 스토리지 컨트롤러 배터리 및 스토리지 캐시 노트: 스토리지 컨트롤러 배터리 상태는 Ready(준비) 또는 Charging(충전 중) 중 하나로 표시 됩니다(Charging(충전 중)은 시스템이 다시 부팅된 후 스토리지 컨트롤러 배터리가 완전히 충전될 때까지 표시됨).
그림 3 확장 선반 구성요소 • 섀시 전면 모습(이미지) - 1 -11 드라이브 위치 및 상태 표시, 드라이브 0은 RAID 6 전용 핫 스페어 • 섀시 후면 모습(이미지) - 냉각 팬의 위치와 상태, 후면 패널 커넥터의 위치 표시 • 서비스 태그 - 선택한 확장 선반의 서비스 태그 나열 • 시스템 하드웨어 상태(표) - 확장 선반의 모든 주요 하드웨어 하위 구성요소의 현재 상태 표시 – 전원 공급 장치 - 상태, 이름 및 위치 – 팬 - 상태, 이름, 속도 및 식별자 – 온도 - 상태, 이름 및 온도 – 스토리지 - 스토리지 실제 디스크(상태, 슬롯, 일련 번호, GHS 상태, 스페어 상태, 스마트 경고 및 크기) – 인클로저 관리 모듈(상태, 이름, 식별자 및 Nexus ID) 사용량 Usage(사용량) 페이지를 표시하려면 Dashboard(대시보드) → Usage(사용량)를 클릭합니다.
노트: The Usage page also displays the Current Time Zone in use for the system. 1. Click the Latest Range option. 2. Select the desired Hours, Days, or Months duration in the Range pull-down list. 3. Enter the desired value in the Display last... drop-down list. For the Hours duration, enter between 1 and 24 hours; for the Days duration, enter between 1 and 31 days; for the Months duration, enter between 1 and 12. 4. Click Apply. 5.
노트: The Usage page also displays the Current Time Zone in use for the system. 1. In the Usage page, select the Time Range option. 2. Type the desired start date in Start Date (or click the calendar icon and make your date selection), or click Now to select the current time (or use the Hour and Minute sliders to set a desired time), and click Done. 3.
• Protocols • Network • Disk • All 노트: If you click All, this displays system usage defined by the range and display options you select, and the file system protocols you have configured. To view all of the displayed usage categories, use the scroll bar on the right-hand side of the page.
• If the selected container includes a CIFS connection type, there will be a CIFS Connection Configuration pane that displays the following categories: CIFS Share Path and Client Access. • If the selected container includes an OST or RDS connection type, the OST or RDS login entry user is listed (for example, backup_user), and there are three tabs: Capacity, Duplication, and Client Statistics.
복제 구성 창 이 창에는 다음과 같은 필드가 포함되어 있습니다. • Enable(활성화) - 예: Yes(예) 또는 No(아니오) • Role(역할) - 예: Source(소스) 또는 Target(대상) • Remote Container Name(원격 컨테이너 이름) - 예: IP Address(IP 주소) 또는 hostname(호스트 이름) • Bandwidth(대역폭) - 예: 기본값, KiB/s, MiB/s 및 GiB/s • Encryption(암호화) - 예: None(없음), AES 128비트 또는 AES 256비트 복제 상태 창 이 창에는 다음과 같은 필드가 포함되어 있습니다.
– Client Statistics tab — contains the Client Statistics pane, which displays Images Ingested, Images Complete, Images Incomplete, Images Restored, Bytes Restored, Image Restore Errors, Image Ingest Errors, Bytes Ingested, Bytes Transferred, and Network Savings (in percentage) statistics. For more information, see Monitoring Container Statistics.
• Images Ingested • Images Complete • Images Incomplete • Images Restored • Bytes Restored • Image Restore Errors • Image Ingest Errors • Bytes Ingested • Bytes Transferred • Network Savings (in percentage) For more information, see Monitoring Container Statistics. 통계: 복제 페이지 Statistics: Replication(통계: 복제) 페이지를 표시하려면 Dashboard(대시보드) → Statistics: Replication(통계: 복제) 을 클릭합니다. 이 페이지에서는 선택하는 피어 DR Series 시스템 또는 복제 컨테이너에 대한 통계를 보고 모니 터링할 수 있습니다. 다음과 같은 두 개의 주요 창으로 구성되어 있습니다.
– 동기화 시간 – 진행률(%) – 복제 처리량 – 네트워크 처리량 – 네트워크 저장량 – 마지막 동기화 시간 – 피어 컨테이너 – 피어 시스템 노트: DR Series 시스템에서 30초마다 통계를 폴링합니다. 복제 필터 설정을 구성한 후에는 Apply Filter(필터 적용)를 클릭하여 Replication Filter(복제 필터) 요약 표에 필터링 된 복제 통계 세트를 표시합니다. Replication Filter(복제 필터) 요약 표에는 선택한 확인란에 해당하는 복제 통계 가 나열됩니다(기본적으로 피어 상태, 복제 상태, 네트워크 처리량, 네트워크 저장량, 진행률(%) 확인란이 선택 되며 표에 표시됨). 확인란 선택을 다시 설정하려면 Reset(재설정)을 클릭합니다. 노트: 6개 이상의 통계 유형을 선택하는 경우 수직 스크롤 막대를 사용하여 통계의 추가 열을 표시합니다. 자세한 내용은 복제 통계 모니터링을 참조하십시오.
– 상태(준비, 판독 중, 초기화 중, 재구축 중, 검색되지 않음으로 스토리지 상태가 표시됨) 노트: Storage Savings(스토리지 저장량) 및 Throughput(처리량)에 나열된 값을 새로 고치려면 를 클릭합 니다.확장 선반 인클로저를 새로 고치려면 Physical Storage(실제 스토리지) 요약 표의 Configured(구성됨) 열 아래에서 Detect(검색)를 클릭합니다. 그러면 다음과 같은 메시지가 포함된 Enclosure Detect(인클로저 검색) 대화상자가 표시됩니다. If the enclosure is undetected, please wait five minutes and try again. If the enclosure still remains undetected after an attempt, keep the enclosure powered On and reboot the appliance(인클로저가 검색되지 않으면 5분 정도 기다린 후에 다시 시도하십시오.
– Trying to Connect – Online – N/A – Marked for Deletion 노트: For newly created OST or RDS containers, the Replication status displays N/A. When replication data has been deleted from an existing OST or RDS container, the Replication status also displays N/A. For existing containers that are in the process of deleting a large amount of data, the Replication status displays Marked for Deletion to indicate that the data deletion process has not yet completed.
Clients To display the Clients page, click Storage → Clients. This page displays the total number of clients that are connected to the DR Series system, which can be a combination of NFS, CIFS, RDS, and OST clients, and this total is listed above the three Client tabs (NFS, CIFS, and RDA tabs). In addition, depending upon the tab type you select, the number of clients for each connection type is displayed.
This page displays an RDS or OST Clients Summary table that lists the following types of RDs or OST client-related information: • Name — lists client by name • Type — lists client type • Plug-In — lists plug-in type that is installed on the client • Backup Software — lists backup software used with this client • Idle Time — lists the idle time for this client • Connection — lists the number of connections for this client • Mode — lists the mode types that can be set for this client: – Auto –
The Schedules page displays the following: • System Time Zone: using the following format (US/Pacific, Tue May 1 10:33:45 2012) • Scheduled Replication operations: with day of the week (Sunday through Saturday), start time, and stop time • Scheduled Cleaner operations: with day of the week (Sunday through Saturday), start time, and stop time 노트: Schedules only control the source container in scheduled Replication operations; the target container is passive in these operations.
• Active Directory • Local Workgroup Users • Email Alerts • Password • Admin Contact Info • Email Relay Host • Date and Time 노트: Each pane title in the System Configuration page serves as a link. To display the corresponding page that provides more detailed information and the related options you can use, click the pane title link. For example, to display the Date and Time page, click the Date and Time pane title link.
Networking The Networking pane displays the currently configured Mode, Hostname, IP Address, Bonding, Domain Suffix, and Primary DNS settings for the DR Series system. The Networking pane title acts as a link to the Networking page: • This page lists the Hostname, IP Address, DNS, Bonding, and installed NICs. The Networking page provides Edit Hostname, Edit IP Address, Edit DNS, Edit Bonding, and Edit MTU options. • This page also displays the interfaces showing bonds and other Ethernet connections.
– Comments – Notify me of DR4000 appliance alerts – Notify me of DR4000 software updates Password The Password Management pane displays the current Reset Password Option set for the system. The Reset Password Option can be: • Service Tag Only • Service Tag and Administrator Email 노트: To select the option Service Tag and Administrator Email, you must first configure the e-mail relay host and administrator contact e-mail.
노트: Editing your existing login password is different than resetting your login password. Click Edit Password in the System Configuration page to edit your login password to reflect any value that meets the system password requirements (for more information, see Modifying the System Password. Click Reset Password in the Login page to reset your login password to the system default value, which requires you to provide the service tag for your system.
지원 페이지 옵션 이해 탐색 패널에 표시되는 Support(지원) 페이지는 3개의 중요한 옵션인 Diagnostics(진단), Software Upgrade(소프트 웨어 업그레이드) 및 License(라이센스)를 제공합니다. 이 세 옵션을 사용하여 다음과 같은 작업을 수행할 수 있 습니다. • • • 진단 로그 파일 생성, 다운로드 또는 삭제 최신 버전의 DR Series 시스템 소프트웨어 업그레이드 추가된 모든 데이터 스토리지 확장 선반의 라이센스 파일 설치 진단 진단 - 이 옵션을 클릭하면 Diagnostics(진단) 페이지가 표시됩니다. 이 페이지에는 파일 이름, 크기, 시간 및 진단 로그 번들이 생성된 날짜, 진단 로그 번들이 생성된 이유, 상태별로 진단 항목 수가 나열됩니다. Diagnostics(진단) 페이지는 Generate(생성), Download(다운로드) 및 Delete(삭제) 옵션을 제공합니다.
스 파일로 업데이트됩니다. Number of Installed Licenses(설치된 라이센스 수) 창에는 ID, 설명, 권한 ID 및 현재 상 태별로 식별된 설치된 라이센스가 나열됩니다. 지원되는 데이터 스토리지 확장 선반 또는 확장 선반에 필요한 라이센스에 대한 자세한 내용은 확장 선반 라이 센스 및 확장 선반 설치를 참조하십시오. Expansion Shelf Licenses This topic introduces the license required for adding external data storage in the form of Dell MD1200 storage arrays that are referred to as expansion shelf enclosures. Expansion shelf enclosures allow you to add supplemental data storage capacity to support DR Series system operations.
노트: 300 GB 드라이브 용량(2.7 TB) 버전의 DR Series 시스템은 확장 선반 인클로저 추가가 지원되지 않습니 다. 1. 탐색 패널에서 Support(지원) → License(라이센스)를 선택하거나 License(라이센스)를 두 번 클릭합니다. License File Location(라이센스 파일 위치) 및 Number of Installed Licenses(설치된 라이센스 수) 창이 있는 License(라이센스) 페이지가 표시됩니다. 2. License File Location(라이센스 파일 위치) 창에서, 라이센스 파일이 있는 경로를 입력하거나(일반적으로 / store/license) Browse...(찾아보기...)를 클릭하여 라이센스 파일 위치를 탐색합니다. 3. Install License(라이센스 설치)를 클릭하고 모든 프롬프트를 따릅니다.
Configuring the DR Series System Settings 4 This topic introduces the concept that before you can run any DR Series system operations, you first need to understand the following key tasks: • How to initialize the system • How to shut down or reboot the system • How to manage the system password Initializing the DR Series system requires that you configure and manage a number of very important system settings.
– • • Slave Interfaces Eth0 – MAC – Maximum Speed – Speed – Duplex Eth1 – MAC – Maximum Speed – Speed – Duplex To configure new networking settings (or to change from those set using the Initial System Configuration Wizard), complete the following: 1. Select System Configuration → Networking. The Networking page is displayed. Select settings for hostname, IP Address, DNS, Bonding, or to view the Ethernet port settings (Eth0-Eth3) for the DR Series system.
노트: In computer networking, jumbo frames are Ethernet frames with more than 1500 bytes of payload (but in some cases, jumbo frames can carry up to 9000 bytes of payload). Many Gigabit Ethernet switches and Gigabit Ethernet network interface cards support jumbo frames. Some Fast Ethernet switches and Fast Ethernet network interface cards also support jumbo frames. Some computer manufacturers use 9000 bytes as the conventional limit for jumbo frame sizes.
12. In Primary DNS, type an IP address that represents the primary DNS server for your system; this is a required field. 13. For Secondary DNS, type an IP address that represents the secondary DNS server for your system; this is an optional field. 14. Click Submit to have the DR Series system accept the new values (or click Cancel to display the Networking page). The Updated DNS dialog is displayed when the selection is successful.
• Max Speed: 1000baseT/Full • Duplex: Full DR Series 시스템 암호 관리 DR Series 시스템에 로그인할 때 사용되는 로그인 암호를 다음 두 가지 방법으로 관리할 수 있습니다. • System Configuration(시스템 구성) 페이지에서 Edit Password(암호 편집) 옵션을 사용하여 기존 로그인 암 호를 수정합니다. 자세한 내용은 시스템 암호 수정을 참조하십시오. • DR Series System Login(DR Series 시스템 로그인) 페이지에서 Reset Password(암호 재설정) 옵션을 사용하 여 로그인 암호를 기본값으로 재설정합니다. 자세한 내용은 기본 시스템 암호 재설정을 참조하십시오.
4. In Service Tag, type the Service Tag associated with your system. 노트: If you are unsure of the Service Tag associated with your DR Series system, it can be found on the Support page (click Support in the navigation panel to display the Support Information pane, which displays the Service Tag). 5. In Administrator Email enter the email address of the administrator of this system. The Administrator Email that you enter must match the administrator email address configured in the DR Series system.
노트: 이 설정은 시스템의 전역 압축 수준입니다. 압축 수준 설정을 변경한 후에는 새로운 수신 데이터(새 설정을 사용하여 작성된 데이터)에만 변경이 적용됩니다. 시스템에 있는 기존의 모든 데이터는 통합되었을 때의 설정이 적용된 상태로 남아 있게 됩니다(새 압축 수준 설정을 사용하여 다시 작성되지 않음). 다음 항목을 선택하여 Compression Level(압축 수준) 페이지에서 압축 수준 설정을 구성합니다. • Fast(고속) - (기본값) 이 옵션을 선택하면 Best(최상) 옵션을 선택했을 때보다 시스템 백업이 빠르게 수행 됩니다. 하지만 공간 저장량이 감소됩니다. • Best(최상) - 이 옵션을 선택하면 시스템 백업 시에 전반적으로 최상의 공간 저장량을 확보할 수 있습니 다. 하지만 백업 프로세스를 완료하는 데 시간이 더 걸립니다. 시스템의 압축 수준 설정을 구성하려면 다음을 수행합니다. 1. Storage(스토리지) → Compression Level(압축 수준)을 선택합니다.
노트: 지원되는 사용자 이름은 최대 64자이며 A-Z, a-z, 0-9, 3개의 특수 문자 대시(-), 마침표(.), 밑 줄(_)을 조합하여 사용할 수 있습니다. 4. – Password(암호)에서, ADS의 암호 지침에 맞는 유효한 암호를 입력합니다. 이 필드는 필수입니다. – Org Unit(조직 단위)에서, ADS의 조직 이름 지침에 맞는 유효한 조직 이름을 입력합니다. 이 필드는 필수입니다. Join Domain(도메인 가입)을 클릭하여 이러한 ADS 설정으로 시스템을 구성하거나 Cancel(취소)을 클릭하여 Active Directory 페이지를 표시합니다. 성공하면 Successfully Configured(구성 완료) 대화상자가 표시됩니다. 노트: CIFS 컨테이너 공유 경로를 구성한 경우 Active Directory 페이지의 CIFS Container Share Path(CIFS 컨테이너 공유 경로) 창에 표시됩니다. 5.
4. 이 로컬 작업 그룹 사용자에서 기존 CIFS 사용자를 삭제하려면 Select(선택)를 클릭하여 로컬 작업 그룹 사용 자 요약 표에서 삭제할 사용자를 식별하고 옵션 모음에서 Delete(삭제)를 클릭합니다. Delete user(사용자 삭제) 확인 대화상자가 표시됩니다. a) OK(확인)를 클릭하여 로컬 작업 그룹 사용자 요약 표에서 선택한 사용자를 삭제하거나 Cancel(취소)을 클릭하여 Local Workgroup Users (CIFS)(로컬 작업 그룹 사용자(CIFS)) 페이지로 돌아갑니다. 작업에 성공하면 Deleted CIFS user(CIFS 사용자 삭제됨) 확인 대화상자가 표시됩니다. 이메일 경고 설정 구성 DR Series 시스템 이메일 경고를 보낼 사용자의 받는 사람 이메일 주소를 생성하고 관리할 수 있습니다.
3. Modify the existing email address you selected as needed, and click Submit. The Email Alerts page is displayed, and a Successfully updated email recipient dialog is displayed when successful. To edit additional recipient email addresses, repeat steps 2 and 3. 4. To delete an existing recipient email address, click Select to indicate the recipient email address entry that you want to delete, and click Delete on the options bar. The Delete Confirmation dialog is displayed. 5.
• 알림 – Notify me of DR4000 appliance alerts(DR4000 어플라이언스 경고 알림) 확인란 상태(활성화됨 또는 비활성화됨) – Notify me of DR4000 software updates(DR4000 소프트웨어 업데이트 알림) 확인란 상태(활성화됨 또 는 비활성화됨) 관리자 연락처 정보 추가 시스템 관리자의 연락처 정보를 구성하려면 다음을 수행합니다. 1. System Configuration(시스템 구성) → Admin Contact Info(관리자 연락처 정보)를 선택합니다. Administrator Contact Information(관리자 연락처 정보) 페이지가 표시됩니다. 2. 옵션 모음에서 Add Contact Information(연락처 정보 추가)을 클릭합니다. Add Administrator Contact Information(관리자 연락처 정보 추가) 대화상자가 표시됩니다. 3.
Managing Passwords You can edit the system password and system password reset configuration on this page. Modifying the System Password To configure a new password or to modify an existing password for logging in to the DR Series system, complete the following: 1. 2. To change the system password, do one of the following:. – In the navigation panel, select System Configuration, the System Configuration page is displayed. Click Password Management.
이메일 릴레이 호스트 구성 네트워크 이메일 시스템에서 필요할 경우 외부 이메일 릴레이 호스트를 DR Series 시스템에 사용할 수 있도록 구 성할 수 있습니다. 이메일 릴레이 호스트는 일반적으로 DR Series 시스템에서 지정된 각 받는 사람 이메일 주소 로 이메일 경고를 전달하는 외부 메일 서버입니다. 이렇게 하려면 Email Relay Host(이메일 릴레이 호스트) 페이지의 옵션 모음에서 Add Relay Host(릴레이 호스트 추 가)를 클릭하여 새 이메일 릴레이 호스트를 정의합니다(또는 Edit Relay Host(릴레이 호스트 편집)를 클릭하여 기 존 이메일 릴레이 호스트 편집). 기존 이메일 릴레이 호스트 편집에 대한 자세한 내용은 이메일 릴레이 호스트 편 집을 참조하십시오. 이메일 릴레이 호스트 추가 DR Series 시스템의 새 이메일 릴레이 호스트를 구성하려면 다음을 수행합니다. 노트: 기존 이메일 릴레이 호스트를 편집하려면 이메일 릴레이 호스트 편집을 참조하십시오. 1.
다. Date and Time(날짜 및 시간) 페이지에는 다음과 같은 날짜 및 시간 관련 설정이 포함된 Settings(설정) 창이 포 함됩니다(초기 시스템 시작 시에 다음과 같은 날짜 및 시간 설정이 기본값으로 설정되어 있음). • Mode(모드) - 수동 및 NTP(Network Time Protocol) 중 하나를 선택합니다. 노트: DR Series 시스템이 작업 그룹에는 속하지만 도메인에 속하지 않을 경우에는 NTP를 사용하는 것이 좋습니다. DR Series 시스템이 Microsoft ADS(Active Directory Services)와 같은 도메인에 가입되 어 있는 경우 NTP가 비활성화되며 DR Series 시스템에서 도메인 시간을 사용합니다. • Time Zone(시간대) - NTP 모드에서, GMT(그리니치 표준시)를 기반으로 시간대 옵션 목록에서 선택합니다 (예: GMT-8:00, 태평양 표준시 (미국과 캐나다)).
c) Click the Calendar icon (adjacent to Set Date and Time), and select the desired day in the month (the system prevents the selection of unsupported days). d) Adjust the Hour and Minute sliders to the desired time (or click Now to set the date and time to be the current date and time in hours and minutes). a) Click Done. The Edit Date and Time dialog is displayed with your new settings. 4. Select NTP. The Edit Date and Time dialog is displayed. 5.
3. Click Another computer, type the hostname or IP address for this DR Series system, and click OK. The Computer Management page is displayed with the designated DR Series system listed in the left pane. 4. Click System Tools, and click Shared folders. The Shares, Sessions, and Open Files folders are displayed in the main pane of the Computer Management page. 5. Click Shares to display a list of the shares managed by the DR Series system. 6.
Managing DR Series Storage Operations 5 Managing Container Operations This topic introduces the concept of using the DR Series system to manage all of your data storage and replication operations. Data storage operations can include tasks such as creating new containers, managing or deleting existing containers, moving data into containers, and displaying current container statistics.
노트: The DR Series system does not support the use of the following special characters in container names: /, #, or @. 4. – A-Z (uppercase letters) – a-z (lowercase letters) – 0-9 (numbers) – dash (-) or underscore (_) special characters In Marker Type, select from the following choices: None, Auto, CommVault, Networker, TSM, or ARCserve. If you select the Auto marker type, this will enable all marker types to be detected.
10. To select a CIFS connection type, click Enable CIFS in the CIFS pane. The Client Access pane is displayed, which allows you to configure this container to use CIFS to backup Microsoft (MS) Windows clients. 11. In the Client Access pane, define a specific CIFS client (or all clients) that can access the CIFS container or manage clients who can access this container: – To allow open access for all clients to the CIFS container you created, select Open Access (all clients have access).
8. – Size: this defines a set limit in Gibibytes (GiB) for incoming raw data allowed per container. Click Create a New Container (or click Cancel to display the Containers page). After creating the new container, the Containers page is displayed and includes a Successfully Added dialog. The list of containers in the Containers summary table is updated with your new container (and its new status is reflected as N/A in the Replication column of this table).
example, CommVault). Conversely, as a best practice, if you have traffic from a DMA that is not one of the supported marker types, it is best to disable marker detection for the container by selecting the None marker type. 4. Modify the connection type options for the selected container as needed (containers support None, NFS/CIFS, and RDA).
Moving Data Into a Container To move data into an existing DR Series system container, complete the following: 1. Click Start → Windows Explorer → Network . The Network page is displayed, which lists all current computers. 2. In the browser Address bar, click Network to select your DR Series hostname or IP address. The Network page is displayed, which lists all current storage and replication containers.
– Capacity Used (system capacity used in Gibibytes or GiBs) – Capacity Free (system capacity free in GiBs) – Read Throughput (read throughput rate in Mebibytes or MiB/s) – Write Throughput (write throughput rate in MiB/s) – Current Files (current number of files in system) – Current Bytes (current number of ingested bytes in system) – Post Dedupe Bytes (number of bytes after deduplication) – Post Compression Bytes (number of bytes after compression) – Compression Status (current compression
• 현재 바이트 수(컨테이너의 현재 통합 바이트 수) • 클리너 상태(선택된 컨테이너의 현재 공간 확보 프로세스 상태) DR Series 시스템 CLI 명령에 대한 자세한 내용은 Dell DR Series 시스템 명령행 참조 안내서를 참조하십시오.
노트: 대역폭은 초당 키비바이트(KiBps), 초당 메비바이트(MiBps), 초당 기비바이트(GiBps) 또는 무제한 대역폭(기본값)으로 설정할 수 있는 복제 대역폭 한도입니다. 2. 옵션 모음에서 Create(생성)를 클릭합니다. Create Replication(복제 생성) 페이지가 표시됩니다. 3. 1단계: 로컬 컨테이너 선택에서, 사용 가능한 컨테이너 목록에서 로컬 컨테이너를 선택합니다. 4. 2단계: 암호화 선택에서 None(없음), 128–bit(128비트) 또는 256–bit(256비트). 중 하나를 선택합니다. 5. 3단계: 역할 선택에서, Source(소스) 또는 Target(대상)을 선택합니다. 6. 4단계: 원격 컨테이너 설정에서, 다음 두 가지 옵션 중 하나를 선택합니다. 7. – Create container on remote system(원격 시스템에 컨테이너 생성). 이 옵션을 선택한 경우 원격 시스템 에 컨테이너 생성(복제)를 참조하십시오.
노트: 소스 및 대상 컨테이너의 복제 방향을 구성할 때 주의해야 합니다. 예를 들어, 대상 컨테이너에는 삭 제된 해당 콘텐츠가 있을 수 있습니다(기존 데이터가 있을 경우). 1. Map to container on remote system(원격 시스템의 컨테이너에 매핑)을 클릭합니다. 2. Username(사용자 이름)에 피어 시스템에 대해 유효한 사용자 이름을 입력합니다(예: administrator). 3. Password(암호)에 피어 시스템에 대해 유효한 암호를 입력합니다(예: St0r@ge!). 4. Peer System(피어 시스템)에 피어 시스템을 나타내는 IP 주소를 입력합니다(예: 10.10.10.10). 5. Remote Container(원격 컨테이너)에서 Retrieve Container(s)(컨테이너 검색)를 클릭하여 목록 상자에 원격 컨 테이너를 표시합니다. 6.
3. Delete replication(복제 삭제) 대화상자에서 OK(확인)를 클릭하거나 Cancel(취소)을 클릭하여 Replication(복 제) 페이지를 표시합니다. 성공하면 Successfully deleted replication(복제 삭제 완료) 대화상자가 표시됩니다. 복제 시작 및 중지 기존 복제 관계에서 복제를 시작하거나 중지하려면 다음을 수행합니다. 노트: 복제 스케줄 설정에 대한 자세한 내용은 복제 스케줄 생성을 참조하십시오. 1. Storage(스토리지) → Replication(복제)을 선택합니다. Replication(복제) 페이지가 표시됩니다. 2. Select(선택)를 클릭하여 복제 프로세스를 중지하거나(3단계 참조) 시작할(4단계 참조) 복제 관계를 식별합 니다. 3. 예약된 복제 프로세스를 중지하려면 Stop(중지)을 클릭하고 OK(확인)를 클릭하여 복제를 중지합니다. Replication(복제) 페이지를 표시하려면 Cancel(취소)을 클릭합니다.
Replication(복제) 페이지가 표시됩니다. 2. Select(선택)를 클릭하여 복제 통계를 표시할 복제 관계를 식별하고 Display Statistics(통계 표시)를 클릭하여 다음 항목이 포함된 Statistics: Replication(통계: 복제) 페이지를 표시합니다. – Replication Filter(복제 필터) - 이 창의 Container Filter(컨테이너 필터) 섹션에서 하나 이상의 복제 컨테 이너, 모든 복제 컨테이너, 하나 이상의 피어 DR Series 시스템을 선택할 수 있습니다. Headers(헤더) 섹션에서는 복제 통계 요약 표에 표시하기 위해 선택할 10개의 통계 유형 확인란을 선택할 수 있습 니다. 기본적으로 Peer Status(피어 상태), Replication Status(복제 상태), Network Throughput(네트워크 처리량), Network Savings(네트워크 저장량), Progress %(진행률 %) 5개의 확인란이 선택됩니다.
노트: If there is no Replication schedule set, but there is pending data that can be replicated, replication will run when it detects the following: 1) there are no active data ingests, and 2) five minutes of system idle time have elapsed since the last data file ingest completed. 노트: The Replication Schedule page displays the current DR Series system time zone and current timestamp (using this format: US/Pacific, Tue Oct 28 14:53:02 2012).
Weekly Replication Schedule Example The following example shows how to set up a weekly Replication schedule with a start time at 01:00 am on Saturday and a stop time at 01:00 am on Sunday. The DR Series system uses the 24-hour clock convention for its time keeping in which each day is divided into twenty-four 1-hour segments. 노트: Replication schedules can only be set on individual replication-enabled source containers that you select from the Container drop-down list.
DR Series 시스템 모니터링 6 이 주제에서는 탐색 패널의 Dashboard(대시보드) 페이지 옵션을 사용하여 DR Series 시스템 작업의 현재 상태를 모니터링하는 방법을 소개합니다. Dashboard(대시보드) 페이지에는 현재 시스템 상태 카테고리의 요약(System State(시스템 상태), HW State(HW 상태), Number of Alerts(경고 수), Number of Events(이벤트 수)와 Capacity(용량), Storage Savings(스토리지 저장량), Throughput(처리량))이 표시되며 System Information(시스템 정보) 창이 포함되 어 있습니다. 구성요소 상태별로 현재 시스템 상태를 표시하고 DR Series 시스템의 현재 시스템 경고 수와 현재 시스템 이벤트 수를 표시하는 데 사용할 수 있는 다른 시스템 페이지(Health(상태), Alerts(경고), Events(이벤트) 페 이지)로 이동되는 링크가 있습니다.
위치 상태 아이콘 설명 시스템 상태 표시줄 최적의 상태를 나타냅니다. 시스템 상태 표시줄 경고 상태를 나타냅니다(단순한 오류가 감지됨). 시스템 상태 표시줄 작동 가능한 상태를 나타냅니다(위험 수준의 오류가 감 지됨). 노트: 현재 HW 상태에 대한 특정 정보를 표시하려면 링크를 클릭하여 Health(상태) 페이지를 표시합니다. Health(상태) 페이지에 전면 및 후면 섀시 모습, 하드 드라이브 표시, 전원 공급 장치, 냉각팬, 연결 위치 등 DR Series 시스템 하드웨어 및 확장 선반 인클로저(설치된 경우)의 현재 상태가 표시됩니다. DR Series 시스 템의 System Hardware Health(시스템 하드웨어 상태) 창은 전원 공급 장치, 냉각팬, 온도, 스토리지, 전압, 네 트워크 인터페이스 카드(NIC), CPU, DIMM 및 NVRAM의 상태를 제공합니다.
• 클리너 상태 • 총 저장량(%) • 모든 컨테이너의 총 파일 수 • 컨테이너 수 • 복제된 컨테이너 수 • 현재 활성 바이트 수(최적화 전의 총 바이트 수) 노트: DR Series 시스템 GUI의 특정 요소에 대한 추가적인 정보를 표시하려면 해당 물음표(?) 아이콘을 클릭 하십시오. 시스템 경고 모니터링 탐색 패널, Dashboard(대시보드) 페이지 및 해당 옵션을 사용하여 DR Series 시스템 경고를 모니터링하고 시스템 의 현재 상태를 표시할 수 있습니다. • Dashboard(대시보드) 페이지의 Number of Alerts(경고 수) 링크를 통해 Alerts(경고) 페이지에 액세스할 수 있습니다. • Dashboard(대시보드)→ Alerts(경고)를 사용하여 탐색 패널에서 Alerts(경고) 페이지에 액세스할 수 있습니 다.
– 메시지(경고에 대한 간략한 설명, 예: Network Interface Controller Embedded (LOM) Port 2 disconnected. Connect it to a network and/or check your network switches or routers for network connectivity issues(내 장형 네트워크 인터페이스 컨트롤러(LOM) 포트 2 연결 끊김. 이 포트를 네트워크에 연결하고 네트워 크 연결 문제가 있는지 네트워크 스위치 또는 라우터를 확인하십시오.) 시스템 이벤트 모니터링 DR Series 시스템 이벤트를 모니터링하고 Events(이벤트) 페이지의 Event Filter(이벤트 필터) 창을 사용하여 표시 할 이벤트를 필터링할 수 있습니다. 이 페이지에 All(모든) 시스템 이벤트가 표시될 수 있습니다. Info(정보), Warning(경고) 또는 Critical(위험) 유형의 이벤트 중 하나로만 이벤트를 제한할 수도 있습니다.
– 7. 구성을 마치면 Done(완료)을 클릭합니다. Start Filter(필터 시작)를 클릭하여 선택한 설정을 기반으로 이벤트 요약 표에 시스템 이벤트를 표시합니다. 이벤트 요약 표에는 색인, 심각도, 타임스탬프, 메시지(이벤트에 대한 간략한 설명)를 기반으로 시스템 이벤 트가 표시됩니다. 이벤트 요약 표의 결과를 탐색하여 표시하려면 다음을 수행합니다. 8. – 페이지별로 표시할 이벤트 수를 설정합니다. 표 오른쪽 하단에서 Events per page(페이지당 이벤트) 를 클릭하고 페이지당 표시할 25개 또는 50개 이벤트를 선택합니다. – 스크롤 막대를 사용하여 각 시스템 이벤트의 전체 페이지를 표시합니다. – 시스템 이벤트의 다른 페이지를 표시하려면 prev(이전) 또는 next(다음)를 클릭하거나, 특정 페이지 번호를 클릭하거나, Goto page(페이지로 이동)에 페이지 번호를 입력하고 Go(이동)를 클릭하여 시스 템 이벤트의 해당 페이지를 표시합니다.
3. Message Contains(메시지에 포함)의 Message(메시지) 텍스트 필드에 검색할 단어 또는 문자열을 입력합니 다. DR Series 시스템은 입력된 항목을 기준으로 대소문자를 구분하지 않고 일치하는 항목을 검색합니다(다 른 검색 옵션은 지원되지 않음). 일치 항목은 이벤트 요약 표에 표시됩니다. 4. Timestamp From(타임스탬프 시작) 옆의 Calendar(달력) 아이콘을 클릭하여 시작 설정 지점을 구성합니다. 시작 설정 지점을 구성하려면 다음을 수행합니다. 5. – 현재 월에서 원하는 날짜를 선택하거나 월 제목 표시줄에서 왼쪽 또는 오른쪽 화살표를 클릭하여 이 전 월 또는 이후 월을 선택합니다. – Hour(시간) 및 Minute(분) 슬라이더를 원하는 시간으로 조정하거나 Now(현재)를 클릭하여 날짜 및 시 간을 현재 날짜 및 시간(시간 및 분)으로 설정합니다. – Done(완료)을 클릭합니다.
Enclosure(인클로저) 탭에는 DR Series 시스템 또는 확장 선반의 모든 주요 구성요소의 현재 상태를 나열하 는 시스템 하드웨어 상태 요약 표가 표시됩니다. 노트: 이 방법은 Dashboard(대시보드) 페이지에서 현재 시스템 상태에 대한 추가 정보를 표시하려는 경 우에 유용합니다. DR Series 시스템 — 시스템 하드웨어 상태 구성요소 – 전원 공급 장치 – 팬 – 온도 – 스토리지 – 전압 – NIC – CPU – DIMM – NVRAM 인클로저 — 시스템 하드웨어 상태 구성요소 – 전원 공급 장치 – 팬 – 온도 – 스토리지 – 인클로저 관리 모듈(EMM) 대시보드 상태 옵션 사용 탐색 패널을 사용하여 설치된 DR Series 시스템 구성요소(또는 확장 선반 인클로저)의 현재 시스템 상태를 표시 하려면 다음을 수행합니다. 1. Dashboard(대시보드) → Health(상태)를 클릭합니다. Health(상태) 페이지가 표시됩니다.
Understanding DR Series System NICs And Ports The DR Series system supports the use of the following types of NICs: • 1-Gigabit Ethernet (GbE) two-port (10-Base T); Dell recommends using CAT6a copper cabling • 10-GbE two-port (100-Base T); Dell recommends using CAT6a copper cabling • 10-GbE SFP+ two-port using LC fiber-optic transceivers or twin-axial cabling The 1-GbE, 10-GbE, and 10-GbE SFP+ NICs configurations bond multiple Ethernet ports into a single interface by default: • For the 1-GbE ports,
반으로 시스템 상태와 현재 표시된 시스템 사용량 상태를 모니터링할 수 있습니다. 이러한 설정에 따라 Usage(사용량) 페이지의 다음과 같은 탭 카테고리에 결과가 표시됩니다. • CPU 로드 • 시스템 • 메모리 • 활성 프로세스 • 프로토콜 • 네트워크 • 디스크 • 모두 노트: All(모두)을 클릭하면 이 탭에 CPU 로드, 시스템 사용량, 메모리 사용량 - 총계, 메모리 사용량 - 실제, 활 성 프로세스 - 총계, NFS 사용량 - 총계, CIFS 사용량 - 총계, 네트워크 사용량, 소켓 사용량 - 총계, 활성 연결, 디스크 사용량 - 메타데이터 및 디스크 사용량 - 데이터 스토리지와 같은 DR Series 시스템 상태 카테고리가 표시됩니다. Displaying Current System Usage To display the current usage for a DR Series system, complete the following: 1.
시간 범위 값 설정 Time Range(시간 범위) 값을 설정하고 이러한 설정을 기반으로 시스템 상태 결과를 표시하려면 다음을 수행합니 다. 1. Dashboard(대시보드) → Usage(사용량)를 클릭합니다. Usage(사용량) 페이지가 표시됩니다. 2. Time Range(시간 범위)를 클릭합니다. 3. Start Date(시작 날짜)에서 Start Date(시작 날짜) 필드 또는 Calendar(달력) 아이콘을 클릭하여 현재 월을 표시 합니다. 이전 월을 선택하려면 월 제목 표시줄에서 왼쪽 화살표를 클릭하여 현재 연도 또는 이전 연도에서 원하는 월을 선택합니다. 4. 선택한 월에서 Start Date(시작 날짜)를 선택하려면 다음 두 가지 방법 중 하나를 수행합니다. 5. – 선택한 월에서 특정 날짜를 선택합니다.(사용 가능한 날짜만 표시됨). 이후 날짜는 사용 불가능으로 간주되어 흐리게 표시됩니다.
The Statistics: Container page is displayed. 2. In the Container Name: drop-down list, select the container you want to monitor. 노트: When you select a container, all statistics displayed on the Statistics: Container page represent specific information about the backup data, throughput, replication, marker type, and connection type for the selected container. The displayed statistics will vary depending upon the connection type used by the specified container. 3.
복제 통계 모니터링 Dashboard(대시보드) → Statistics: Replication(통계: 복제)을 클릭하여 Replication Filter(복제 필터) 창에서 선택한 하나 이상의 컨테이너, 하나 이상의 피어 DR Series 시스템에 대한 복제 통계를 표시하고 모니터링할 수 있습니 다. 구성된 설정에 따라 아래 항목의 복제 통계를 모니터링하고 표시할 수 있습니다. • 모든 컨테이너 • 하나 이상의 특정 컨테이너 • 하나 이상의 다른 DR Series 시스템 Replication Filter(복제 필터) 창에는 Container Filter(컨테이너 필터)에서 선택하는 컨테이너 또는 다른 피어 DR Series 시스템에 대한 복제 통계를 표시할 수 있는 10개의 헤더 확인란이 있습니다. 컨테이너, 피어 시스템 및 복제 통계 카테고리를 선택한 후에 Apply Filter(필터 적용)를 클릭하여 선택한 검색 기 준에 맞게 복제 통계 결과를 표시합니다.
노트: The following five types of replication statistics are enabled by default: Peer Status, Replication Status, Network Throughput, Network Savings, and Progress %. If you choose more than five types of statistics (when you select additional check boxes), a horizontal scroll bar appears at the bottom of the Replication Statistics table. Use this scroll bar to display the columns of additional statistics that may not display within the main window. 4.
DR Series 시스템 지원 옵션 사용 7 Support(지원) 페이지와 Diagnostics(진단), Software Upgrade(소프트웨어 업그레이드), License(라이센스) 옵션을 사용하여 DR Series 시스템의 상태를 유지할 수 있습니다. 이러한 옵션에 액세스하려면 DR Series 시스템 탐색 패 널을 사용하거나(예: Support(지원)→ Diagnostics(진단)를 클릭하여 Diagnostics(진단) 페이지 표시) Support(지원) 페이지에서 Diagnostics(진단), Software Upgrade(소프트웨어 업그레이드) 또는 License(라이센스) 링크를 사용하 십시오.
노트: 진단 로그 파일, 로그 파일 디렉터리 및 진단 서비스에 대한 자세한 내용은 진단 서비스 정보를 참조 하십시오. DR Series 진단 로그 파일은 최신 시스템 설정을 기록하는 다양한 파일 유형이 포함되어 있고 이를 압축된 .lzip 파 일 형식으로 저장하는 번들입니다. Diagnostics(진단) 페이지에서는 다음과 같은 속성으로 각 진단 로그 파일을 식별합니다. • 파일 이름 - __
To generate a diagnostics log file bundle for your system, complete the following: 1. Select Support → Diagnostics in the navigation panel. The Diagnostics page is displayed, and this page lists all current diagnostics log files. 2. Click Generate. A New log file is scheduled dialog is displayed. 3. To verify that a new diagnostics log file is being generated, check the status of the diagnostics log file by selecting Support → Diagnostics.
3. OK(확인)를 클릭하여 선택한 진단 로그 파일을 삭제하거나 Cancel(취소)을 클릭하여 Diagnostics(진단) 페이 지를 표시합니다. 성공하면 Log file was removed successfully(로그 파일 제거 완료) 대화상자가 표시됩니다. DR Series System Software Upgrade When you initiate a DR Series system software upgrade, the navigation panel displays only the Support page and the Software Upgrade options.
The Software Upgrade page is displayed. 2. Verify the currently installed DR Series system software version listed as Current Version in the Software Information pane (all previously installed versions are listed under Upgrade History, showing the version number and timestamp when installed).
노트: If the DR Series system software upgrade operation fails, you can reboot the system and attempt another software upgrade operation using the DR Series system GUI. If this is unsuccessful, you can use the DR Series system CLI system --show command to view the current System State status. DR Series system software upgrades can also be performed using the DR Series system CLI. For details, see the Dell DR Series System Command Line Reference Guide at dell.com/support/manuals/.
Linux 또는 Unix 시스템에서 RM 이미지를 USB 키로 전송하려면 다음을 수행합니다. 1. 2. 다운로드한 RM 이미지 파일을 Linux 또는 Unix 시스템에 복사합니다. Linux 또는 Unix 시스템에서 사용 가능한 USB 포트에 USB 키를 삽입합니다. 운영 체제에서 보고된 장치 이름을 기록합니다(예: /dev/sdc4). 3. 이때 파일 시스템에 USB 장치를 로컬로 장착하지 마십시오. 4. dd 명령을 사용하여 RM 이미지를 USB 키에 복사합니다. dd if= of= bs=4096k 예를 들어, 다음과 같습니다. dd if=/root/DR4100-UM-04.49.01.00.00.34555.img of=/dev/sdc4 bs=4096 복원 관리자(RM) 실행 Dell 복원 관리자(RM) 유틸리티를 실행하려면 RM USB 키 만들기에서 생성된 RM USB 키를 사용하여 DR Series 시 스템을 부팅하십시오. 1.
To resolve this issue, reset the Dell PERC H700 BIOS to revise the proper boot order setting to configure the proper boot LUN to be RAID1. To reset the proper LUN boot order, complete the following steps: 1. Start Restore Manager. 2. Select Option 1 → Recover My Appliance. 3. Click Proceed. The OS Virtual Disk is created: Warning Code 2002 dialog is displayed. The Operating System installation was successful dialog is displayed. 4. Click Reboot, and during reboot, press Ctrl+R to enter the PERC BIOS.
DR Series 시스템 및 NVRAM: NVRAM은 DR Series 시스템에서 FRU(Field Replaceable Unit)입니다. NVRAM DDR(double-data rate) 메모리의 동력 인 슈퍼 커패시터는 전원이 유실된 동안에 내용을 SSD(Solid State Drive)로 이동할 수 있어야 합니다. 이렇게 데이터를 전송하려면 시스템이 3분 동안 작동되도록 전원을 유지해야 합니다(일반적으로 약 1분 정도 소 요). SSD로 데이터를 백업하는 동안 문제가 발생하면 이후에 시스템을 다비 부팅하면 이를 감지합니다. 다음과 같은 상황에서 NVRAM에 백업 오류가 발생할 수 있습니다. • 전원이 중단된 동안 NVRAM이 데이터 백업에 실패했습니다. • 슈퍼 커패시터가 SSD에 DDR 내용을 백업할 수 있는 충분한 전원을 유지하지 않는 경우. • NVRAM/SSD에 줄 끝(EOL) 또는 다른 오류가 발생하는 경우.
올바르게 초기화되면 DR Series 시스템이 자동으로 유지 관리 모드로 전환됩니다. 파일 시스템 검사기가 모 든 블록맵과 데이터스토어를 조사하여 장애가 발생한 NVRAM으로 인해 얼마나 많은 데이터가 유실되었는 지 판별합니다.
OST 구성 및 사용 8 이 주제에서는 주요 OpenStorage Technology(OST) 작업에 대해 설명하며 이러한 작업을 수행할 수 있는 절차가 포함된 기타 OST 관련 주제로 연결되는 링크를 제공합니다. • OST 및 지원되는 DMA에 사용하도록 DR Series 시스템 구성. 자세한 내용은 Backup Exec GUI를 사용하여 DR Series 시스템 구성 및 NetBackup을 사용하여 DR Series 시스템 정보 구성을 참조하십시오. • DR Series 시스템 GUI를 사용하여 LSU(Logical Storage Unit) 구성. 자세한 내용은 LSU 구성을 참조하십시 오. • 지원되는 매체 서버(Linux 또는 Windows)에 Dell OST 플러그인 설치. 자세한 내용은 Linux용 OST 플러그인 설치 또는 Windows용 OST 플러그인 설치를 참조하십시오.
• OST 및 DMA 통합: – • • OpenStorage API를 통해 DMA와 매체 서버 소프트웨어 간의 통신 가능 – DMA를 크게 변경하지 않고도 DR Series 시스템 스토리지 기능을 사용할 수 있음 – 기본으로 제공되는 DMA 정책을 사용하여 백업 및 복제 작업이 간소화됨 DR Series 시스템 및 OST 포트와 쓰기 작업: – 제어 채널이 TCP 포트 10011 사용 – 데이터 채널이 TCP 포트 11000 사용 – 최적화된 쓰기 작업으로 인해 클라이언트측 중복 제거 가능 DR Series 시스템 간의 복제 작업: – 소스 또는 대상 DR Series 시스템에서 구성이 필요하지 않음 – 복제는 컨테이너 기반이 아닌 파일 기반 – DMA 최적화된 중복 작업에 의해 복제 트리거됨 – DR Series 시스템이 데이터 파일 전송(매체 서버 아님) – 중복 작업 후에 DR Series 시스템이 DMA에 카탈로그를 업데이트하라고 알림(보조 백업 승인)
OST 지침 최상의 결과를 위해, 다음 지침을 검토하여 DR Series 시스템의 지원되는 OpenStorage Technology(OST) 작업에서 최적의 성능을 달성할 수 있습니다. • 백업, 복원 및 최적화된 중복 작업은 Dell OST 플러그인을 통해 수행해야 합니다. 노트: Dell OST 플러그인은 클라이언트측 중복 제거를 지원할 수 있도록 클라이언트 시스템에 설치 해야 합니다. • 최적의 지원되는 집계 처리 속도: – 패스트루 쓰기 작업의 경우 3 TB/시 – 최적화된 쓰기 작업의 경우 4 TB/시 노트: 패스트루 쓰기는 데이터에 최적화를 적용하지 않고 매체 서버에서 DR Series 시스템으로 데이 터를 보내는 시점입니다. 반면에, 최적화된 쓰기는 데이터에 최적화를 적용한 후에 매체 서버에서 DR Series 시스템으로 데이터를 보내는 시점입니다.
Supported OST Software and Components This topic provides a brief listing of some of the supported OST software and components that can be used with the DR Series system. 노트: For the latest list of supported DMAs and OST plug-ins, see the Dell DR Series System Interoperability Guide, at support.dell.com/manuals. 표 5.
– – Version 2010 R3 (Windows Server 2008 R2, 64–bit) Version 2012 (Windows Server 2008 R2, 64–bit) 노트: The Dell DR Series system licensing is all-inclusive, so that no additional Dell licensing is required to use OST or the optimized duplication capability. The Dell OST plug-in that gets installed on a supported Linux or Windows media server platform is a free download from Dell. However, Symantec NetBackup requires that you purchase a Symantec OpenStorage Disk Option license.
5. In Connection Type, set the container type to OST. The OST pane is displayed, and this is where you can set the capacity for the OST connection type container. 6. In Capacity, select either the Unlimited or Size options to set the capacity for the OST connection type container. If you select Size, make sure to define the desired size in Gibibytes (GiB). 7. Click Create a New Container (or click Cancel to display the Containers page).
– Click Storage → Clients – Click the OST tab in the Clients page, and click Download Plug-In – Select the appropriate plug-in in the Download Plug-Ins page, and click Download Once downloaded, run the Dell OST Plug-In Installer to install the plug-in on your designated Linux-based media server. For specifics, see Installing the OST Plug-In for NetBackup on Linux. 노트: The Dell OST plug-in needs to be installed on client systems to support client-side deduplication.
When the plug-in has been installed, the Completed the Dell Storage Plug-In for Symantec OST Setup Wizard page is displayed. 9. Click Finish to exit the wizard. Installing the OST Plug-In for NetBackup on Windows This topic describes how to install the Dell OST plug-in on a media server running the supported Microsoft Windows server operating system software (and using the NetBackup DMA).
제어판 페이지가 표시됩니다. 2. 프로그램 및 기능 아래에서 프로그램 제거를 클릭합니다. 프로그램 제거 또는 변경 페이지가 표시됩니다. 3. 설치된 프로그램 목록에서 Dell OST 플러그인을 찾아 마우스 오른쪽 단추로 클릭한 후 제거를 선택합니다. 프로그램 및 기능 확인 대화상자가 표시됩니다. 4. Dell OST 플러그인 제거에서 예를 클릭합니다. Linux에서 NetBackup용 OST 플러그인 설치 이 주제에서는 NetBackup DMA를 사용하여 지원되는 Red Hat Enterprise Linux 또는 SUSE Linux 서버 운영 체제 소 프트웨어를 실행하는 매체 서버에 Dell OST 플러그인을 설치하는 방법에 대해 설명합니다. 지정된 매체 서버의 올바른 디렉터리에 Dell OST 플러그인 설치 프로그램이 다운로드되어 있어야 합니다. Dell OST 플러그인 설치 프로그램은 Dellostplugin-x86_64-xxxxx.bin.gz으로 저장됩니다.
Linux용 Dell OST 플러그인 제거 Linux 기반 매체 서버에서 Dell OST 플러그인을 제거해야 할 경우 다음 제거 프로세스를 따르십시오. 1. -uninstall 옵션을 사용하기 전에 NetBackup nbrmms 서비스를 중지합니다. OST 플러그인 제거를 시도할 때 NetBackup nbrmms 서비스가 실행 중이면 OST 플러그인 설치 프로그램이 오류를 반환합니다. 2. -uninstall 옵션을 사용하여 OST 플러그인 설치 프로그램을 실행하고 다음 명령을 사용하여 플러그인을 제거 합니다. $> ./Dellostplugin-x86_64-xxxxx.bin -uninstall 노트: OST 플러그인을 제거하기 전에 NetBackup nbrmms 서비스를 중지해야 합니다(플러그인을 제거 하려면 Dell OST 플러그인 설치 프로그램을 사용해야 함). 3. Linux 매체 서버에서 다음 NetBackup 명령을 사용하여 플러그인이 제거되었는지 확인합니다.
Using NetBackup CLI to Add DR Series System Name (Linux) This topic describes how to use the NetBackup CLI to add the DR Series system name to each Linux-based media server you plan to use with the DR Series system. 1. Add the DR Series system name to NetBackup by using the following command: /usr/openv/netbackup/bin/admincmd/nbdevconfig -creatests -storage_server servername -stype DELL -media_server mediaservername 2.
* 암호 확인 자격 증명은 DR Series 시스템에 필요한 자격 증명과 동일해야 합니다. 자세한 내용은 LSU 구성을 참조하십 시오. 4. Next(다음)를 클릭합니다. 5. Next(다음)를 클릭합니다. 구성한 값이 나열된 Storage Server Configuration Summary(스토리지 서버 구성 요약) 페이지가 표시됩니다. 구성한 스토리지 서버 및 해당 자격 증명이 Storage Server Creation Status(스토리지 서버 생성 상태) 페이지 에 표시됩니다. 6. Next(다음), Finish(마침)를 차례로 클릭하여 스토리지 서버 구성 마법사를 닫습니다. Storage server servername successfully created(스토리지 서버(서버 이름) 생성 완료) 페이지가 표시됩니다. 이제 DR Series 시스템에 사용할 수 있도록 NetBackup이 구성되었습니다.
To display the disk pool you created, click Devices → Disk Pools in the left navigation pane in the NetBackup Administrator console. 디스크 풀을 사용하여 스토리지 장치 생성 NetBackup GUI를 사용하여 DR Series 시스템의 디스크 풀을 통해 스토리지 장치를 생성합니다. NetBackup에 로그인하고 다음을 수행합니다. 1. NetBackup Administrator(NetBackup 관리자) 콘솔 기본 창의 왼쪽 탐색 창에서 Storage(스토리지)를 클릭하고 Storage Units(스토리지 장치)를 선택합니다. 2. NetBackup Administrator(NetBackup 관리자) 콘솔 기본 창의 드롭다운 목록에서 New Storage Unit(새 스토리 지 장치)를 선택합니다. 3.
To monitor the status of any restore operation, click Activity Monitor in the left navigation pane of the NetBackup Administrator console, and select the restore job you are interested in to view details about the operation.
1. The Backup Exec installation must be running on one of the supported Windows platforms. 2. Dell recommends that the DR Series system appliance have an OST container created and configured. For details, see Configuring an LSU. 3. The Windows OST installer must be present. If not, download the Windows installer (DellOSTPlug-in.msi), which is available at support.dell.com/support/drivers, to a network directory location you can access. 4.
Backup Exec을 사용하여 DR Series 시스템에서 백업 생성 이 주제에서는 Backup Exec을 사용하여 DR Series 시스템에 백업을 생성하는 방법에 대해 설명합니다. Backup Exec을 사용하여 DR Series 시스템에 백업을 생성하려면 다음을 수행합니다. 노트: 이 절차에서는 Backup Exec 2010을 사용하여 프로세스를 설명합니다. Backup Exec 2012의 절차는 이와 다릅니다. 특정 세부정보 및 절차를 보려면 해당 DMA 및 버전의 Symantec 제품별 문서를 참조하십시오. 1. Backup Exec Administrator(Backup Exec 관리자) 콘솔에 로그인하고 Job Setup(작업 설정) 탭을 선택합니다. 2. 왼쪽 탐색 패널에서 Backup Tasks(백업 작업)를 클릭하고 New job(새 작업)을 선택합니다. 3.
– Server type—select the type of server from the drop-down list (DELL). – Logical storage unit—enter the name of the logical storage unit (LSU), also known as a DR Series system container, to use. 4. Click Yes in response to the prompt if you want to make the new device the default destination for new jobs. 5. Close the Add OpenStorage Device page. 6. Click the Job Setup tab. 7. In the left navigation pane, select Backup Tasks, and click New job to duplicate backup sets.
Dedupe Not Supported Supported Not Supported Not Supported Passthrough Supported Supported Supported Supported Supported DR Series System CLI Commands for OST The following are the supported DR Series system CLI commands for OST operations: administrator@acme100 > ost Usage: ost --show [--config] [--file_history] [--name ] [--clients] [--limits] ost --setpassword ost --delete_client --name ost --update_client --name --mode
Windows용 OST 플러그인 로그 회전 기본적으로, Windows 로그 회전 크기는 10메가바이트(MB)에서 설정됩니다. 로그 파일의 크기가 이 값에 도달하 면 OpenStorage Transport(OST) 플러그인이 자동으로 기존 로그 파일 이름을 libstspiDell.log에서 libstspiDell.log.old 로 변경하고 새 로그를 생성합니다. 로그 회전 크기 수정 로그 회전 크기를 수정하려면 다음 레지스트리 키 값을 편집합니다. HKLM\Software\Dell\OST\LogRotationSize 이 값을 수정하면 새 회전 크기 값이 즉시 적용됩니다(백업 프로세스를 다시 시작할 필요가 없음). Linux 유틸리티를 사용하여 진단 수집 Dell_diags라고 하는 Linux 유틸리티를 사용하여 Linux 전용 클라이언트에서 진단을 수집할 수 있습니다. 이 Linux 유틸리티는 OST 플러그인에 의해 /opt/Dell 디렉터리에 설치됩니다.
Linux 매체 서버의 NetBackup Linux 매체 서버에서 실행되는 NetBackup의 경우 다음과 같은 파일을 수집할 것을 권장합니다. • 매체 서버의 OST 플러그인 구성 파일 및 로그 파일 – • • 위치: /var/log/libstspiDell.log.* 매체 서버의 NetBackup 백업 작업 로그 및 명령 로그: – 위치: NetBackup 로그 파일은 /usr/openv/netbackup/logs/에 있습니다. NetBackup의 각 프로세스의 경우, 로그 디렉터리에 하위 디렉터리가 있습니다. 주요 프로세스 관련 로그에는 bptm, bpdm, bprd, bpcd, bpbrm이 있습니다. – 이 5개의 디렉터리가 기본적으로 제공되지 않을 수 있으므로 매체 서버에 있는 경우에만 이러한 로그를 수집하십시오.
– 다음 예제에서와 같이 이 텍스트를 창에 복사하여 붙여넣습니다. Faulting application bptm.exe, version 7.0.2010.104, time stamp 0x4b42a78e, faulting module libstspiDellMT.dll, version 1.0.1.0, time stamp 0x4f0b5ee5, exception code 0xc0000005, fault offset 0x000000000002655d, process id 0x12cc, application start time 0x01cccf1845397a42. – 시스템이 응답하지 않으면 bptm.exe 크래시를 강제 적용하고 다음을 수행합니다. 1. Task Manager(작업 관리자)를 클릭하여 엽니다. 2. 프로세스를 찾습니다. 3. 마우스 오른쪽 단추를 클릭하고 Create Dump File(덤프 파일 생성)을 선택합니다. 4.
Configuring and Using Rapid Data Storage 9 RDS Overview Rapid Data Storage (RDS) provides the logical disk interface that can be used with network storage devices. The Dell DR Series system requires the Dell Rapid OFS (ROFS) plug-in to integrate its data storage operations with the Dell Quest NetVault Backup (NVBU). The ROFS plug-in is installed by default on the NVBU server and the Dell DR Series system when the latest software updates are installed.
RDS Guidelines For best results, observe the following guidelines for optimal performance with your supported RDS operations with the DR Series system: • Back up, restore, and optimized duplication operations performed using the Dell ROFS plug-in 노트: The Dell ROFS plug-in is installed on client systems to support client-side deduplication. • Optimal supported aggregated throughput rates: – 3.8 Terabytes per hour (TB/hr) for passthrough write operations – 7.
You can turn On or turn Off client-side optimization (also known as client-side deduplication) using the DR Series system CLI commands, rda --update_client --name --mode. For more information about DR Series system CLI commands, see the Dell DR Series System Command Line Reference Guide, available at support.dell.com/manuals. Adding RDS Devices in NVBU To add RDS devices in the NVBU: 1. Log on to your NVBU media server and launch NVBU console. 2. Click Device Management.
Backing Up Data on the RDS Container Using NVBU You must back up data on the RDS container (available on the DR Series systems) using NVBU. Before you can back up data using the RDS protocol, you must create an RDS container on the DR Series system and add that container as an RDA device on NVBU. For more information see, Adding RDA Device on NVBU. To back up data on the RDS container: 1. In the NVBU Console, click Backup. The NVBU Backup window is displayed. 2.
14. Select the Advanced Options tab, and select the relevant options. 15. To run the backup job, click the Submit icon. The backup job may take a few minutes to complete depending on the amount of data that is backed up. You can view the progress of the backup job on NVBU, using the Job Management section of NVBU. 노트: For more information on Dell Quest NetVault Backup, see the Dell Quest NetVault Backup Administrator’s Guide.
13. Select the Advanced Options tab and select the relevant options. 14. To run the optimized replication job, click the Submit icon. 노트: For more information on Dell Quest NetVault Backup, see the Dell Quest NetVault Backup Administrator’s Guide. Restoring Data From a DR Series System Using NVBU Use NVBU to restore data from a RDS container on a DR Series system. To restore data from a DR Series system using NVBU: 1. In the NVBU Console, click Restore. The NVBU Restore window is displayed. 2.
노트: For more information on Dell Quest NetVault Backup, see the Dell Quest NetVault Backup Administrator’s Guide.
Troubleshooting and Maintenance 10 This topic provides an overview of the basic troubleshooting and maintenance information that is available to help you better understand the current state of your DR Series system.
Dell 지원팀의 개입이 필요한 경우 Dell 지원팀에 도움을 요청하는 방법을 알려주는 기타 경고 및 이벤트 메시지 도 있습니다. • 표 1은 시스템 경고 유형별로 DR Series 시스템 경고 메시지를 나열합니다(일반 시스템, 시스템 섀시, NVRAM, 백업 및 중복 제거 관련 작업 중에 표시될 수 있는 PERC 관련 경고 메시지). • 표 2는 1부터 7까지 시스템 이벤트 유형별로 DR Series 시스템 이벤트 메시지를 나열합니다(백업, 복제, 중 복 제거, 진단, 클리너, DataCheck, 유지 관리, OpenStorage Technology(OST) 작업 중에 표시될 수 있는 이벤 트 메시지). 표 7. DR Series 시스템 경고 메시지 경고 메시지 설명/의미 또는 조치 일반적인 시스템 경고 파일 시스템 검색이 요청되었습니다. 시스템이 유지 관리 모드로 전환 중입니다. 파일 시스 템의 액세스 권한이 읽기 전용입니다. NVRAM이 감지되지 않았습니다.
경고 메시지 설명/의미 또는 조치 스토리지 사용량이 시스템 용량에 근접합니다. 파일 시스템을 정리하십시오. 문제가 지속되면 Dell 지 원팀에 가능한 지원 또는 개입을 요청하십시오. 복제 재동기화를 계속 진행할 수 없습니다. 네임스페이스 한도가 최대값에 도달했습니다. 복제 대상의 공간이 부족합니다. 파일 시스템을 정리하십시오. 문제가 지속되면 Dell 지 원팀에 가능한 지원 또는 개입을 요청하십시오. 파일 시스템이 허용되는 파일 및 디렉터리 최대 한도 에 도달했습니다. 새 파일 및 디렉터리 생성이 거부됩 니다. 파일 시스템을 정리하십시오. 문제가 지속되면 Dell 지 원팀에 가능한 지원 또는 개입을 요청하십시오. 시스템 섀시 경고 전원 공급 장치 <숫자>에서 장애를 감지했습니다. • • • 지정된 전원 공급 장치의 전원 케이블이 분리되 어 있으면 다시 연결하십시오. 전원 케이블에 입력 AC 전원이 있는지 확인하 십시오. 다른 전원 코드를 사용하십시오.
경고 메시지 설명/의미 또는 조치 • • 네트워크 인터페이스 컨트롤러가 누락되었습니다. • • 네트워크를 확인하십시오. 그래도 문제가 해결 되지 않으면 NIC를 교체하십시오. NIC가 내장되어 있으면 DR Series 시스템 어플 라이언스에 서비스가 필요합니다. NIC를 분리했다가 다시 삽입하십시오. 그래도 문제가 해결되지 않으면 NIC를 교체하 십시오. 네트워크 인터페이스 컨트롤러 <이름>의 연결이 끊어 네트워크에 컨트롤러를 연결하고 네트워크 스위치 또 졌습니다. 는 라우터에 네트워크 연결 문제가 있는지 확인하십시 오. 네트워크 인터페이스 컨트롤러 <이름>이(가) 비활성 화되었습니다. 지정된 NIC의 포트를 활성화하십시오. 네트워크 인터페이스 컨트롤러 <이름> 드라이버가 잘 DR Series 시스템 어플라이언스를 업그레이드하십시오 못되었습니다. (소프트웨어 업그레이드 페이지에서 업그레이드 시작 클릭). CPU <이름>에 오류가 발생했습니다. 오류가 발생한 지정된 프로세서를 교체하십시오.
경고 메시지 설명/의미 또는 조치 여 DR Series 시스템 어플라이언스에 서비스가 필요한지 확인하도록 합니다. 스토리지 컨트롤러 <숫자>에 오류가 발생했습니다. DR Series 시스템의 RAID 컨트롤러를 교체하십시오. 스토리지 컨트롤러 <숫자>이(가) 누락되었습니다. DR Series 시스템의 RAID 컨트롤러를 다시 삽입하거나 교체하십시오. 스토리지 컨트롤러 <숫자>의 구성이 잘못되었습니다. 필요한 가상 드라이브 개수가 <숫자>이지만, 실제로 발 견된 가상 드라이브 개수는 <숫자>입니다. Dell 복원 관리자(RM) 유틸리티를 실행하여 드라이브 구성 불일치를 복구하십시오. 필요한 인클로저 개수가 <숫자>이지만, 실제로 발견된 인클로저 개수는 <숫자>입니다. • • 스토리지 컨트롤러와 모든 해당 인클로저 간의 SAS 케이블 연결을 확인하십시오. 인클로저 전원 공급 장치의 전원 케이블 연결을 확인하십시오. 실제 디스크 <숫자>에 장애가 발생했습니다.
경고 메시지 에 장애가 발생했습니다. 설명/의미 또는 조치 • • • 이(가) 누락되었습니다. • • 장치가 있는지 확인하고 케이블이 올바르게 연 결되어 있는지 확인하십시오. 자세한 내용은 Dell DR Series 시스템 소유자 매뉴얼을 참조하 여 시스템 케이블 연결이 올바른지 확인하십시 오. 컨트롤러 배터리와의 연결 및 배터리 상태를 확 인하십시오. 이러한 단계를 수행해도 문제가 해결되지 않으 면 스토리지 컨트롤러 배터리를 교체하십시오. 장치가 있는지 확인하고 케이블이 올바르게 연 결되어 있는지 확인하십시오. 자세한 내용은 Dell DR Series 시스템 소유자 매뉴얼을 참조하 여 시스템 케이블 연결이 올바른지 확인하십시 오. 컨트롤러 배터리와의 연결 및 배터리 상태를 확 인하십시오. 노트: 배터리 충전 상태가 약하거나 감소되면 이 경 고가 발생할 수 있습니다. 스토리지 에 장애가 발생했습니다.
경고 메시지 스토리지 어플라이언스 위험 오류: 이 스토리지 어플 라이언스가 제대로 작동되기 위한 BIOS 시스템 ID가 올바르지 않습니다. 설명/의미 또는 조치 • Dell 지원팀에 도움을 요청하십시오. • DR Series 시스템 어플라이언스에 서비스가 필 요합니다. Dell 지원팀에 도움을 요청하십시오. • 표 8. DR Series 시스템 이벤트 메시지 시스템 이벤트 메시지 설명/의미 또는 조치 시스템 이벤트 = 유형 1 시스템 메모리 사용량이 최적 수준으로 복귀되었 습니다. 정보용 메시지. 사용자 개입이 필요하지 않습니다. 높은 수준의 시스템 프로세스 사용량이 감지되었 습니다. 이 상태가 지속되면 시스템 진단을 수집하 십시오. 정보용 메시지. 사용자 개입이 필요하지 않습니다. 시스템 프로세스 사용량이 최적 수준으로 복귀되 었습니다. 정보용 메시지. 사용자 개입이 필요하지 않습니다. NVRAM PCI 컨트롤러에서 고온 판독값이 감지되었 정보용 메시지.
시스템 이벤트 메시지 설명/의미 또는 조치 마지막 부팅 중에 NVRAM이 데이터를 백업하거나 복원하지 못했습니다. Dell 지원팀에 지원 또는 개입을 요청하십시오. NVRAM 하드웨어 오류가 발생했습니다. Dell 지원팀에 지원 또는 개입을 요청하십시오. 데이터 볼륨이 없습니다. 모든 드라이브가 삽입되 어 전원이 켜져 있는지 확인하십시오. Dell 지원팀에 지원 또는 개입을 요청하십시오. 여러 번 시도했지만 파일 시스템 서버 시작에 실패 했습니다. Dell 지원팀에 지원 또는 개입을 요청하십시오. 파일 시스템 서버가 여러 번 손상되었습니다. 시스 템이 현재 유지 관리 모드로 전환 중입니다. Dell 지원팀에 지원 또는 개입을 요청하십시오. 디스크 공간이 부족합니다. 파일 시스템이 읽기 전 용 모드로 전환되었습니다. 정보용 메시지. 사용자 개입이 필요하지 않습니다. 문제가 지속되면 Dell 지원팀에 지원 또는 개입을 요청하십시오.
시스템 이벤트 메시지 설명/의미 또는 조치 파일 시스템 네임스페이스 파티션이 허용되는 최 대 한도에 도달했습니다. 오래 되어 사용되지 않는 파일을 삭제하거나 복제를 비활 성화하십시오. 문제가 지속되면 Dell 지원팀에 지원 또는 개입을 요청하십시오. 파일 시스템 네임스페이스 파티션이 허용되는 최 대 한도에 근접합니다. 새 복제 재동기화가 중지됩니다. 문제가 지속되면 Dell 지 원팀에 지원 또는 개입을 요청하십시오. 하나 이상의 소프트웨어 패키지가 호환되지 않습 니다. 문제를 해결하려면 시스템 어플라이언스를 업그레이드 하십시오. DR Series 시스템 어플라이언스를 업그레이드 하십시오(소프트웨어 업그레이드 페이지에서 업그레이 드 시작 클릭). 시스템 이벤트 = 유형 2 <이름> 컨테이너가 성공적으로 생성되었습니다. 정보용 메시지. 사용자 개입이 필요하지 않습니다. <이름> 컨테이너가 삭제되도록 표시되었습니다. 자세한 내용은 컨테이너 삭제를 참조하십시오.
시스템 이벤트 메시지 설명/의미 또는 조치 <이름> 컨테이너의 복제 재동기화를 시작하는 중 에 오류가 발생했습니다. 자세한 내용은 복제 작업 관리를 참조하십시오. 스냅샷 <변수> → <변수>이(가) 성공적으로 생성되 정보용 메시지. 사용자 개입이 필요하지 않습니다. 었습니다. 스냅샷 <변수> → <변수>이(가) 성공적으로 업데이 정보용 메시지. 사용자 개입이 필요하지 않습니다. 트되었습니다. 스냅샷 <변수> → <변수>이(가) 성공적으로 삭제되 정보용 메시지. 사용자 개입이 필요하지 않습니다. 었습니다. 온라인 데이터 확인 <변수>에 성공했습니다. 정보용 메시지. 사용자 개입이 필요하지 않습니다. <변수>의 <변수> 시스템 마커에 성공했습니다. 정보용 메시지. 사용자 개입이 필요하지 않습니다. <변수> 스케줄이 성공적으로 업데이트되었습니다. 정보용 메시지. 사용자 개입이 필요하지 않습니다. 시스템 이벤트 = 유형 3 시스템이 유지 관리 모드로 전환됩니다. 정보용 메시지.
시스템 이벤트 메시지 설명/의미 또는 조치 네임스페이스에서 불일치 항목이 발견되었습니다. DR Series 시스템 CLI maintenance --filesystem --start_scan 명령을 사용하여 파일 시스템 일관성 검사를 예약하십시 오. 시스템이 유지 관리 모드로 전환됩니다. 네임스페 이스 로그 재생에 실패했습니다. Dell 지원팀에 지원 또는 개입을 요청하십시오. 시스템이 유지 관리 모드로 전환됩니다. 네임스페 이스 트랜잭션 오류입니다. Dell 지원팀에 지원 또는 개입을 요청하십시오. 오류 - 네임스페이스 트랜잭션 커밋에 실패했습니 다. Dell 지원팀에 지원 또는 개입을 요청하십시오. 파일 시스템이 지원되는 최대 네임스페이스 항목 수에 도달했습니다. 새 파일 및 디렉터리 생성 작업이 허용되도록 파일 시스템 을 정리하십시오. 상태가 지속되면 Dell 지원팀에 지원 또 는 개입을 요청하십시오. 사용 가능한 네임스페이스 항목이 부족한 파일 시 스템이 복구되었습니다.
시스템 이벤트 메시지 설명/의미 또는 조치 <변수> 컨테이너의 복제 이름 서비스 볼륨 작업 로 그(oplog)가 가득 찼습니다. 복제 작업용 포트(9904, 9911, 9915, 9916)와 OST 작업용 포트 (10011, 11000)가 활성화되어 있는지 확인하십시오. 문제가 지속되면 Dell 지원팀에 지원 또는 개입을 요청하십시오. <변수> 컨테이너의 손상된 이름 서비스 볼륨 작업 로그(oplog)로 인해 DR Series가 유지 관리 모드로 전환됩니다. DR Series 시스템에서 자체 수정됩니다. 상태가 지속되면 아이노드(inode) 수를 줄이거나 Dell 지원팀에 지원 또는 개입을 요청하십시오. <변수> 컨테이너에 대한 복제 데이터 작업 로그 (oplog)가 가득 찼습니다. DR Series 시스템에서 자체 수정됩니다. 상태가 지속되면 아이노드(inode) 수를 줄이거나 Dell 지원팀에 지원 또는 개입을 요청하십시오.
시스템 이벤트 메시지 설명/의미 또는 조치 실행 중인 복제 대상 시스템 <변수>의 공간이 부족 합니다. <변수> 컨테이너에서 복제를 계속 진행할 수 없습니다. 정보용 메시지. Dell 지원팀에 지원 또는 개입을 요청하십 시오. <변수> 컨테이너에서 잘못된 복제 구성이 감지되 었습니다. 대상 시스템 <변수>에서 복제 관계가 강 제로 삭제되었을 수 있습니다. 정보용 메시지. Dell 지원팀에 지원 또는 개입을 요청하십 시오. <변수> 컨테이너의 복제 실패, 오류 <변수>. 진단 로그 파일 번들을 수집하고 Dell 지원팀의 도움을 받 아 지원 레코드를 여십시오. <변수> 컨테이너에 대해 복제 서버가 블록맵을 커 밋하지 못했습니다. 시스템이 유지 관리 모드로 전 환됩니다. DR Series 시스템에서 자체 수정됩니다. 상태가 지속되면 아이노드(inode) 수를 줄이거나 Dell 지원팀에 지원 또는 개입을 요청하십시오.
시스템 이벤트 메시지 설명/의미 또는 조치 온라인 데이터 확인(DataCheck)에서 <변수> 손상이 정보용 메시지. 문제가 지속되면 Dell 지원팀에 지원 또는 감지되었습니다. 개입을 요청하십시오. 온라인 데이터 확인(DataCheck) 시작에 실패했습니 정보용 메시지. 문제가 지속되면 Dell 지원팀에 지원 또는 다. 개입을 요청하십시오. 시스템 이벤트 = 유형 4 중복 제거 사전 <변수>을(를) 로드할 수 없습니다. DR Series 시스템 CLI maintenance --configuration -reinit_dictionary 명령을 사용하십시오. 이 문제가 지속되 면 Dell 지원팀에 지원 또는 개입을 요청하십시오. 중복 제거 사전 <변수>을(를) 찾을 수 없습니다. DR Series 시스템 CLI maintenance --configuration -reinit_dictionary 명령을 사용하십시오. 문제가 지속되면 Dell 지원팀에 지원 또는 개입을 요청하십시오.
시스템 이벤트 메시지 설명/의미 또는 조치 데이터 볼륨을 읽는 중에 오류가 발생했습니다. DR Series 시스템에 유지 관리 기반 문제가 발생했습니다. 유지 관리 모드 또는 DR Series 시스템 CLI 명령을 사용하 여 상태를 확인하십시오. 필요한 경우 Dell 지원팀에 문의 하십시오. 데이터 볼륨에 쓰는 중에 오류가 발생했습니다. DR Series 시스템에 유지 관리 기반 문제가 발생했습니다. 유지 관리 모드 또는 DR Series 시스템 CLI 명령을 사용하 여 상태를 확인하십시오. 필요한 경우 Dell 지원팀에 문의 하십시오. 메타데이터의 체크섬 확인에 실패했습니다. Dell 지원팀에 도움을 요청하거나 파일 시스템을 복구하 십시오. 복구에 대해서는 DR Series 유지 관리 모드 정보를 참조하십시오. 최적화 엔진 로그 재생에 실패했습니다. Dell 지원팀에 도움을 요청하거나 파일 시스템을 복구하 십시오. 복구에 대해서는 DR Series 유지 관리 모드 정보를 참조하십시오.
시스템 이벤트 메시지 설명/의미 또는 조치 스케줄에 따라 클리너 프로세스가 중지되었습니 다. <변수>에 다시 시작됩니다. 정보용 메시지. 사용자 개입이 필요하지 않습니다. 클리너가 <변수>에 중단되었습니다. DR Series 시스템이 유지 관리 모드로 전환되고 클리너 프 로세스가 다시 시작됩니다. NVRAM의 데이터 이동에 실패했습니다. 시스템이 유지 관리 모드로 전환됩니다. 정보용 메시지. 사용자 개입이 필요하지 않습니다. 마지막 이벤트/유효하지 않은 이벤트. 정보용 메시지. Dell 지원팀에 지원 또는 개입을 요청하십 시오. 스케줄에 따라 파일 시스템 클리너 프로세스가 시 작되었습니다(<변수>까지 활성 상태가 됨). 정보용 메시지. 사용자 개입이 필요하지 않습니다. 스케줄에 따라 파일 시스템 클리너 프로세스가 중 지되었습니다(<변수>에 다시 시작됨). 정보용 메시지. 사용자 개입이 필요하지 않습니다. 시스템 이벤트 = 유형 5 관리자가 시스템 종료를 시작했습니다.
시스템 이벤트 메시지 설명/의미 또는 조치 네트워크 MTU 크기가 <변수>(으)로 설정되었습니 다. 정보용 메시지. 사용자 개입이 필요하지 않습니다. 시스템 이름이 <변수>(으)로 설정되었습니다. 정보용 메시지. 사용자 개입이 필요하지 않습니다. 이메일 경고에 대해 이메일 릴레이 호스트가 <변수 정보용 메시지. 사용자 개입이 필요하지 않습니다. >(으)로 설정되었습니다. 이메일 경고의 받는 사람이 <변수>(으)로 설정되었 정보용 메시지. 사용자 개입이 필요하지 않습니다. 습니다. <변수> 받는 사람이 이메일 경고를 수신하도록 추 가되었습니다. 정보용 메시지. 사용자 개입이 필요하지 않습니다. <변수> 받는 사람이 더 이상 이메일 경고를 수신하 지 않습니다. 이메일 받는 사람이 있는지 또는 사서함이 가득 찼는지 확 인하십시오. 이메일 경고에 대한 관리자 정보가 <변수>(으)로 설 정보용 메시지. 사용자 개입이 필요하지 않습니다. 정되었습니다. 테스트 이메일을 보냈습니다. 정보용 메시지.
시스템 이벤트 메시지 설명/의미 또는 조치 CIFS 사용자 <변수>이(가) 추가되었습니다. 정보용 메시지. 사용자 개입이 필요하지 않습니다. CIFS 사용자 <변수>이(가) 삭제되었습니다. 정보용 메시지. 사용자 개입이 필요하지 않습니다. CIFS 사용자 <변수>의 암호가 변경되었습니다. 정보용 메시지. 사용자 개입이 필요하지 않습니다. 시스템 업그레이드가 <변수> 완료되었습니다. 정보용 메시지. 사용자 개입이 필요하지 않습니다. <변수> 디스크에서 외부 구성이 지워졌습니다. 정보용 메시지. 사용자 개입이 필요하지 않습니다. <변수> 사용자가 시스템에 로그인되었습니다. 정보용 메시지. 사용자 개입이 필요하지 않습니다. <변수> 디스크가 핫 스페어로 구성되었습니다. 정보용 메시지. 사용자 개입이 필요하지 않습니다. <변수> 디스크에서 외부 구성이 지워졌습니다. 정보용 메시지. 사용자 개입이 필요하지 않습니다. 텔넷 서비스가 활성화되었습니다. 정보용 메시지.
시스템 이벤트 메시지 설명/의미 또는 조치 OST 서버 시작에 실패했습니다. OST 서버를 다시 시작하십시오. 문제가 지속되면 Dell 지 원팀에 지원 또는 개입을 요청하십시오. OST 서버가 성공적으로 중지되었습니다. 정보용 메시지. 사용자 개입이 필요하지 않습니다. OST 클라이언트 인증에 실패했습니다. OST 클라이언트 인증을 다시 시도하십시오. 문제가 지속 되면 Dell 지원팀에 지원 또는 개입을 요청하십시오. OST LSU(Logical Storage Unit) 할당량 초과됨 <변수 >. 정보용 메시지. LSU 수를 줄이십시오. 문제가 지속되면 Dell 지원팀에 지원 또는 개입을 요청하십시오. OST 백업 실패 <변수>. OST 백업 작업을 다시 시도하십시오. 문제가 지속되면 Dell 지원팀에 지원 또는 개입을 요청하십시오. OST Opdup 실패 <변수>. OST 최적화된 중복 프로세스에 실패했습니다. 문제가 지 속되면 Dell 지원팀에 지원 또는 개입을 요청하십시오.
이 기능에 액세스하려면 다음 DR Series 시스템 탐색 패널 GUI 옵션을 사용하십시오. • Support(지원) → Diagnostics(진단) 시스템에서 문제 또는 오류 상태를 진단할 때 유용한 모든 시스템 관련 정보를 수집하면 진단 서비스가 작동됩 니다. 진단 로그 파일 번들에 대한 자세한 내용은 진단 페이지 및 옵션을 참조하십시오. 진단은 시스템이 구동될 때 서비스로 실행되며 이 프로세스는 들어오는 요청을 수신 대기합니다. 두 가지 방법 으로 진단 수집 프로세스가 시작됩니다. • 관리자 생성 모드: 관리자가 DR Series 시스템 CLI 또는 DR Series 시스템 GUI 요청을 수행하는 경우(및 표 시되는 기본 이유가 관리자 생성). • 자동 생성 모드: 프로세스 또는 서비스 장애가 보고되고 DR Series 시스템이 시스템 관련 정보를 수집하 기 시작합니다. 자동 생성 수집이 완료되면 시스템 이벤트가 생성됩니다.
When in its Maintenance mode, the filesystem is in a read-only state, and the system runs the following maintenancebased operations: 노트: Whenever the DR Series systems enters or exits from the Maintenance mode state, all communication via CIFS, NFS, RDA, or OST is lost. • Runs an internal filesystem check. • Generates a filesystem status report (if the filesystem check finds no issues, the DR Series system switches back to Operational mode without user intervention).
– BIOS Version 노트: When in Maintenance mode, the DR Series system navigation panel displays the following options that are links to display the correspond page in the DR Series system GUI: • Alerts • Events • Health • Usage • Diagnostics • Software Upgrade Once the DR Series system enters Maintenance mode, there can only be two possible outcome states: • Operational mode (Normal State): where the filesystem check was successful, and no system files need to be repaired (Filesystem Check: succe
• Contacting Dell Support for technical assistance. For more information, see Contacting Dell. 노트: Dell recommends that you generate a DR Series system diagnostics file whenever the DR Series system is in its Maintenance or Support modes if one was not automatically generated. When in the Support mode, the DR Series system displays the following alert message: The server is currently in Support mode. To continue, you must contact Dell Support at http://www.support.dell.
The Cleaner Schedule page is displayed. 2. Click Schedule to create a new schedule (or click Edit Schedule to modify an existing schedule). The Set Cleaner Schedule page is displayed. 3. Select (or modify) the Start Time and Stop Time setpoint values using the Hour and Minutes pull-down lists to create a Cleaner schedule. 노트: You must set a corresponding Stop Time for every Start Time set in each Cleaner schedule you create.
• 현재 실행 3단계 시작 시간(현재 클리너 프로세스 3단계의 시작 날짜 및 시간을 나타냄) • 처리된 현재 실행 3단계 레코드(현재 클리너 프로세스 3단계에서 처리된 데이터 레코드 수 나열) • 현재 실행 3단계 종료 시간(현재 클리너 프로세스 3단계의 종료 날짜 및 시간을 나타냄) • 현재 실행 4단계 시작 시간(현재 클리너 프로세스 4단계의 시작 날짜 및 시간을 나타냄) • 처리된 현재 실행 4단계 레코드(현재 클리너 프로세스 4단계에서 처리된 데이터 레코드 수 나열) • 현재 실행 4단계 종료 시간(현재 클리너 프로세스 4단계의 종료 날짜 및 시간을 나타냄) DR Series 시스템 CLI 명령에 대한 자세한 내용은 Dell DR Series 시스템 명령행 참조 안내서를 참조하십시오.
Supported Ports in a DR Series System 11 The following table lists the application and service ports found on a normally operating DR Series system. There may be other ports that are not listed here, that an administrator may need to open and enable to support specific operations across the network. Be aware that the ports listed in the following table may not reflect your specific network environment, or any planned deployment.
Port Type Number Port Usage or Description TCP 199 SNMP daemon—used by Simple Network Management Protocol (SNMP) requests TCP 801 NFS status daemon 180
12 도움말 보기 DR Series 시스템의 문제를 직접 해결할 수 있는 방법 또는 Dell의 기술 지원을 얻는 방법에 대해서는 문제 해결 및 유지 관리, 오류 조건 문제 해결,Dell 지원팀에 문의하기 전에 및 Dell에 문의하기를 참조하십시오. Dell 지원팀에 문의하기 전에 오류 상태 또는 작동 문제가 발생한 경우 Dell 지원팀에 기술 지원을 요청하기 전에 Dell DR Series 시스템 지원 문 서를 사용하여 문제를 해결할 수 있는지 확인할 것을 권장합니다. Dell DR Series 시스템에 발생하는 기본적인 문제를 분리하거나 진단할 수 있도록 다음과 같은 작업을 수행하는 것이 좋습니다. • • Dell DR Series 시스템 관리자 안내서를 참조하여 문제를 설명하거나 해결할 수 있는 정보가 포함되어 있 는지 확인합니다. 9장, “문제 해결 및 유지 관리”를 참조하십시오.
노트: 인터넷이 연결되어 있지 않을 경우 매입서, 패킹 슬립, 청구서 또는 Dell 제품 카탈로그에 연락처 정보 를 찾아볼 수 있습니다. Dell은 온라인과 전화를 통한 몇 가지 지원 및 서비스 옵션을 제공합니다. 이러한 옵션은 국가 및 제품에 따라 다 르며 일부 서비스의 경우 해당 지역에 제공되지 않을 수 있습니다. 영업 지원, 기술 지원 또는 고객 서비스 문제에 대해 Dell에 문의하려면 다음을 수행합니다. 1. support.dell.com을 참조하십시오. 2. support.dell.com 페이지 하단에 있는 국가/지역을 선택하여 클릭합니다. 전체 목록의 국가 및 지역을 보려면 All(모두)을 클릭합니다. Choose a Country/Region(국가/지역 선택) 페이지가 표시됩니다. 3. Americas(미국), Europe, Middle East, & Africa(유럽, 중동 및 아프리카) 또는 Asia Pacific(아시아 태평양) 중에 서 국가/지역을 선택하여 클릭합니다. 4.