Administrator Guide

ManualsBrandsDell ManualsAccess PlatformsC9010 Modular Chassis Switch

Dell EMC Networking Configuration Guide for

the C9010 Series

Version 9.14.2.5

Summary of content (1040 pages)

PAGE 1
Dell EMC Networking Configuration Guide for the C9010 Series Version 9.14.2.
PAGE 2
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. NOTE: A WARNING indicates a potential for property damage, personal injury, or death. © 2018 - 2019 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
PAGE 3
Contents 1 About this Guide......................................................................................................................... 32 Audience............................................................................................................................................................................... 32 Conventions..................................................................................................................................................................
PAGE 4
Applying a Privilege Level to a Username...................................................................................................................55 Applying a Privilege Level to a Terminal Line............................................................................................................. 55 Configuring Logging............................................................................................................................................................
PAGE 5
The Port-Authentication Process..................................................................................................................................... 82 EAP over RADIUS..........................................................................................................................................................82 Configuring 802.1X..........................................................................................................................................................
PAGE 6
Applying Egress ACLs...................................................................................................................................................116 Applying Layer 3 Egress ACLs on Control-Plane Traffic......................................................................................... 117 Counting ACL Hits........................................................................................................................................................ 117 IP Prefix Lists.....
PAGE 7
Origin............................................................................................................................................................................. 165 AS Path......................................................................................................................................................................... 166 Next Hop...........................................................................................................................................
PAGE 8
Storing Last and Bad PDUs....................................................................................................................................... 200 Capturing PDUs............................................................................................................................................................201 PDU Counters..............................................................................................................................................................
PAGE 9
DCB Configuration Exchange....................................................................................................................................250 Configuration Source Election...................................................................................................................................250 Propagation of DCB Information...............................................................................................................................
PAGE 10
Configuring the Server for Automatic Address Allocation......................................................................................315 Specifying a Default Gateway.................................................................................................................................... 316 Configure a Method of Hostname Resolution..........................................................................................................316 Using DNS for Address Resolution...................
PAGE 11
FIP Snooping in a Switch Stack....................................................................................................................................... 341 Using FIP Snooping............................................................................................................................................................341 FIP Snooping Prerequisites.........................................................................................................................................
PAGE 12
Sample Configuration and Topology...............................................................................................................................366 FRRP Support on VLT...................................................................................................................................................... 367 19 GARP VLAN Registration Protocol (GVRP)................................................................................370 Configure GVRP...................................
PAGE 13
Interface Types..................................................................................................................................................................392 View Basic Interface Information.................................................................................................................................... 393 Resetting an Interface to its Factory Default State.....................................................................................................
PAGE 14
Non Dell-Qualified Transceivers....................................................................................................................................... 419 Splitting QSFP Ports to SFP+ Ports.............................................................................................................................. 420 Converting a QSFP or QSFP+ Port to an SFP or SFP+ Port...............................................................................
PAGE 15
25 IPv6 Routing.......................................................................................................................... 446 Protocol Overview............................................................................................................................................................ 446 Extended Address Space...........................................................................................................................................
PAGE 16
Configuring Authentication Passwords.....................................................................................................................477 Setting the Overload Bit............................................................................................................................................. 477 Debugging IS-IS...........................................................................................................................................................
PAGE 17
mac learning-limit mac-address-sticky.....................................................................................................................508 mac learning-limit station-move................................................................................................................................ 508 mac learning-limit no-station-move..........................................................................................................................
PAGE 18
Limiting the Source-Active Cache............................................................................................................................ 545 Clearing the Source-Active Cache............................................................................................................................545 Enabling the Rejected Source-Active Cache...........................................................................................................
PAGE 19
MLD timers........................................................................................................................................................................ 592 Reducing Host Response Burstiness........................................................................................................................592 Configuring MLD Version.................................................................................................................................................
PAGE 20
OSPF ACK Packing......................................................................................................................................................613 Setting OSPF Adjacency with Cisco Routers...........................................................................................................613 Configuration Information.................................................................................................................................................
PAGE 21
Electing an RP using the BSR Mechanism.................................................................................................................... 649 Creating Multicast Boundaries and Domains.................................................................................................................650 Enabling PIM-SM Graceful Restart................................................................................................................................
PAGE 22
Important Points to Remember.......................................................................................................................................692 PE Stack Configuration.................................................................................................................................................... 692 Configuring a PE Stack...............................................................................................................................................
PAGE 23
Upgrading the PoE Controller....................................................................................................................................728 Suspending Power Delivery on the Port Extender..................................................................................................728 Restoring Power Delivery on the Port Extender..................................................................................................... 728 Monitor the Power Budget.........................
PAGE 24
Configuring a Weight for WRED and ECN Operation............................................................................................ 762 Pre-Calculating Available QoS CAM Space................................................................................................................... 763 SNMP Support for Buffer Statistics Tracking...............................................................................................................763 47 Routing Information Protocol (RIP)..............
PAGE 25
Privilege Levels Overview.......................................................................................................................................... 805 Configuration Task List for Privilege Levels.............................................................................................................805 RADIUS...............................................................................................................................................................................
PAGE 26
Marking Egress Packets with a DEI Value................................................................................................................847 Dynamic Mode CoS for VLAN Stacking.........................................................................................................................848 Mapping C-Tag to S-Tag dot1p Values.................................................................................................................... 849 Layer 2 Protocol Tunneling................
PAGE 27
Copy a Binary File to the Startup-Configuration..................................................................................................... 873 Additional MIB Objects to View Copy Statistics......................................................................................................873 Obtaining a Value for MIB Objects............................................................................................................................
PAGE 28
Adding an Interface to the Spanning Tree Group.........................................................................................................902 Modifying Global Parameters.......................................................................................................................................... 902 Modifying Interface STP Parameters.............................................................................................................................903 Enabling PortFast.......
PAGE 29
Multipoint Receive-Only Tunnels.................................................................................................................................... 929 Guidelines for Configuring Multipoint Receive-Only Tunnels................................................................................ 929 59 Upgrade Procedures................................................................................................................931 60 Uplink Failure Detection (UFD)...............................
PAGE 30
Configuring Route Leaking with Filtering..................................................................................................................961 Configuring Route Leaking without Filtering Criteria..............................................................................................962 64 Virtual Link Trunking (VLT)..................................................................................................... 964 Overview............................................................
PAGE 31
65 Virtual Router Redundancy Protocol (VRRP)........................................................................... 1005 VRRP Overview...............................................................................................................................................................1005 VRRP Benefits................................................................................................................................................................. 1006 VRRP Implementation...........
PAGE 32
1 About this Guide This Configuration guide provides information about how to use and configure the software features supported in the Dell Networking operating system (OS) on a C9010 console to configure a C9010 switch, C1048P, N20xx, and N30xx port extenders. The C9010 switch is also referred to as network director or control bridge. The port extenders are also referred to as rapid access nodes. Though this guide contains information on protocols, it is not intended to be a complete reference.
PAGE 33
2 Configuration Fundamentals The Dell Networking OS command line interface (CLI) is a text-based interface you can use to configure interfaces and protocols. The CLI is structured in modes for security and management purposes. Different sets of commands are available in each mode, and you can limit user access to modes using privilege levels. After you enter a command, the command is added to the running configuration file.
PAGE 34
• EXEC Privilege mode has commands to view configurations, clear counters, manage configuration files, run diagnostics, and enable or disable debug operations. The privilege level is 15, which is unrestricted. You can configure a password for this mode; refer to the Configure the Enable Password section in the Getting Started chapter.
PAGE 35
GRUB BGP ADDRESS-FAMILY ROUTER ISIS ISIS ADDRESS-FAMILY ROUTER OSPF ROUTER OSPFV3 ROUTER RIP SPANNING TREE TRACE-LIST VLT DOMAIN VRRP UPLINK STATE GROUP Navigating CLI Modes The Dell Networking OS prompt changes to indicate the CLI mode. The following table lists the CLI mode, its prompt, and information about how to access and exit the CLI mode.
PAGE 36
CLI Command Mode Prompt Access Command Port-channel Interface Dell(conf-if-po-0)# interface (INTERFACE modes) Tunnel Interface Dell(conf-if-tu-0)# interface (INTERFACE modes) VLAN Interface Dell(conf-if-vl-0)# interface (INTERFACE modes) STANDARD ACCESS-LIST Dell(config-std-nacl)# ip access-list standard (IP ACCESS-LIST Modes) EXTENDED ACCESS-LIST Dell(config-ext-nacl)# ip access-list extended (IP ACCESS-LIST Modes) IP COMMUNITY-LIST Dell(config-community-list)# ip community-list CONSOL
PAGE 37
CLI Command Mode Prompt Access Command EIS Dell(conf-mgmt-eis)# management egress-interfaceselection FRRP Dell(conf-frrp-ring-id)# protocol frrp LLDP Dell(conf-lldp)# or Dell(conf-if —interface-lldp)# protocol lldp (CONFIGURATION or INTERFACE Modes) LLDP MANAGEMENT INTERFACE Dell(conf-lldp-mgmtIf)# management-interface (LLDP Mode) LINE Dell(config-line-console) or Dell(config-line-vty) line console orline vty MONITOR SESSION Dell(conf-mon-sess-sessionID)# monitor session OPENFLOW INSTAN
PAGE 38
System image file is "system://A" System Type: C9010 Control Processor: Intel Rangeley with 2 Gbytes (2127536128 bytes) of memory, core(s) 2. Route Processor: Intel Rangeley with 2 Gbytes (2127536128 bytes) of memory, core(s) 2. 16G bytes of boot flash memory. 2 Route Processor Module. 3 24-port TE/GE (VG) 3 24-port TE/GE (VG) 4 6-port TE/FG (VG) 2 4-port TE/GE (VG) 208 Ten GigabitEthernet/IEEE 802.3 in10 Forty GigabitEthernet/IEEE 802.
PAGE 39
debug --More-• Debug functions Enter ? after a partial keyword lists all of the keywords that begin with the specified letters. Dell(conf)#cl? class-map clock Dell(conf)#cl • Enter [space]? after a keyword lists all of the keywords that can follow the specified keyword. Dell(conf)#clock ? summer-time Configure summer (daylight savings) time timezone Configure time zone Dell(conf)#clock Entering and Editing Commands Notes for entering commands. • • The CLI is not case-sensitive.
PAGE 40
Command History The Dell Networking OS maintains a history of previously-entered commands for each mode. For example: • • When you are in EXEC mode, the UP and DOWN arrow keys display the previously-entered EXEC mode commands. When you are in CONFIGURATION mode, the UP or DOWN arrows keys recall the previously-entered CONFIGURATION mode commands.
PAGE 41
The find keyword displays the output of the show command beginning from the first occurrence of specified text. The following example shows this command used in combination with the show processes command. Example of the find Keyword Dell#show processes cpu cp | find system 0 72900 7290 10000 17.79% 17.93% 538 42710 4271 10000 6.52% 7.74% 535 50600 5060 10000 3.56% 3.61% 720 290 29 10000 0.20% 0.07% 614 250 25 10000 0.00% 0.03% 615 130 13 10000 0.00% 0.02% 508 290 29 10000 0.00% 0.02% 655 270 27 10000 0.
PAGE 42
3 Getting Started This chapter describes how you start configuring your operating software. When you power up the chassis, the system performs a power-on self test (POST) and loads the Dell Networking operating software. Boot messages scroll up the terminal window during this process. No user interaction is required if the boot process proceeds without interruption. When the boot process completes, the system status LED remains online (green) and the console monitor displays the EXEC mode prompt.
PAGE 43
Accessing the Console Port To access the console port, follow these steps: For the console port pinout, refer to Accessing the RJ-45 Console Port with a DB-9 Adapter. 1. Install an RJ-45 copper cable into the console port. Use a rollover (crossover) cable to connect the switch console port to a terminal server. 2. Connect the other end of the cable to the DTE terminal server. 3.
PAGE 44
the mount command is saved to the startup configuration. As a result, each time the device re-boots, the NFS file system is mounted during start up. Table 4. Forming a copy Command Location source-file-url Syntax destination-file-url Syntax For a remote file location: copy nfsmount://{}/filepath/filename} username:password tftp://{hostip | hostname}/ filepath/filename NFS File System Important Points to Remember • • • • You cannot copy a file from one remote system to another.
PAGE 45
Default Configuration Although a version of the Dell Networking OS is pre-loaded on the switch, the system is not configured when you power up the first time (except for the default hostname, which is Dell). You must configure the system using the CLI. Configuring a Host Name The host name appears in the prompt. The default host name is Dell. • • Host names must start with a letter and end with a letter or digit. Characters within the string can be letters, digits, and hyphens.
PAGE 46
Configure a Management Route Define a path from the switch to the network from which you are accessing the system remotely. Management routes are separate from IP routes and are only used to manage the switch through the management port. • Configure a management route to the network from which you are accessing the system. CONFIGURATION mode management route ip-address/mask gateway • • • ip-address: the network address in dotted-decimal format (A.B.C.D).
PAGE 47
• • enable secret is stored in the running/startup configuration using MD5 encryption method. enable sha256-password is stored in the running/startup configuration using sha256-based encryption method (PBKDF2). Dell Networking recommends using the enable sha256-password password. To configure an enable password, use the following command. • Create a password to access EXEC Privilege mode.
PAGE 48
• To copy a local file to a remote system, combine the file-origin syntax for a local file location with the file-destination syntax for a remote file location. To copy a remote file to Dell Networking system, combine the file-origin syntax for a remote file location with the file-destination syntax for a local file location. • Table 5.
PAGE 49
EXEC Privilege mode copy running-config scp://{hostip | hostname}/ filepath/filename NOTE: When copying to a server, a host name can only be used if a DNS server is configured. NOTE: When you load the startup configuration or a configuration file from a network server such as TFTP to the running configuration, the configuration is added to the running configuration. This does not replace the existing running configuration.
PAGE 50
Example of the show running-config Command Dell#show running-config Current Configuration ... ! Version 1-0(0-4013) ! Last configuration change at Wed Jun 3 16:24:25 2015 by admin ! boot system rpm0 primary system: A: boot system rpm0 secondary tftp://10.16.127.35/DT-MAA-C9000-3 boot system rpm0 default system: A: boot system rpm1 primary system: A: boot system rpm1 secondary tftp://10.16.127.35/DT-MAA-C9000-3 boot system rpm1 default system: A: boot system gateway 10.16.127.
PAGE 51
[May [May [May [May [May [May [May 17 17 17 17 17 17 17 10:16:53]: CMD-(CLI):[service timestamps log datetime utc]by default from console 10:17:05]: CMD-(CLI):[show clock]by default from console 10:17:20]: CMD-(CLI):[show running-config]by default from console 10:17:30]: CMD-(CLI):[interface tengigabitethernet 1/2]by default from console 10:17:32]: CMD-(CLI):[shutdown]by default from console 10:17:34]: CMD-(CLI):[no shutdown]by default from console 10:17:40]: CMD-(CLI):[write memory]by default from consol
PAGE 52
• 52 Using Hashes to Validate Software Images Getting Started
PAGE 53
4 Switch Management Configuring Privilege Levels Privilege levels restrict access to commands based on user or terminal line. There are 16 privilege levels, of which three are pre-defined. The default privilege level is 1. Level Description Level 0 Access to the system begins at EXEC mode, and EXEC mode commands are limited to enable, disable, and exit. Level 1 Access to the system begins at EXEC mode, and all commands are available.
PAGE 54
Allowing Access to the Following Modes This section describes how to allow access to the INTERFACE, LINE, ROUTE-MAP, and ROUTER modes. Similar to allowing access to CONFIGURATION mode, to allow access to INTERFACE, LINE, ROUTE-MAP, and ROUTER modes, you must first allow access to the command that enters you into the mode. For example, to allow a user to enter INTERFACE mode, use the privilege configure level level interface tengigabitethernet command.
PAGE 55
Current privilege level is 3.
PAGE 56
To disable logging, use the following commands. • Disable all logging except on the console. • CONFIGURATION mode no logging on Disable logging to the logging buffer. • CONFIGURATION mode no logging buffer Disable logging to terminal lines. • CONFIGURATION mode no logging monitor Disable console logging. CONFIGURATION mode no logging console Audit and Security Logs This section describes how to configure, display, and clear audit and security logs.
PAGE 57
Example of Enabling Audit and Security Logs Dell(conf)#logging extended Displaying Audit and Security Logs To display audit logs, use the show logging auditlog command in Exec mode. To view these logs, you must first enable the logging extended command. Only the RBAC system administrator user role can view the audit logs. Only the RBAC security administrator and system administrator user role can view the security logs.
PAGE 58
Pre-requisites To configure a secure connection from the switch to the syslog server: 1. On the switch, enable the SSH server Dell(conf)#ip ssh server enable 2. On the syslog server, create a reverse SSH tunnel from the syslog server to the switch, using following syntax: ssh -R :: user@remote_host -nNf In the following example the syslog server IP address is 10.156.166.48 and the listening port is 5141. The switch IP address is 10.16.131.
PAGE 59
change the default value to any number of days from 1 to 30. By default, login activity tracking is disabled. You can enable it using the login statistics enable command from the configuration mode. Restrictions for Tracking Login Activity These restrictions apply for tracking login activity: • • Only the system and security administrators can configure login activity tracking and view the login activity details of other users.
PAGE 60
Unsuccessful login attempt(s) in last 30 day(s): 3 Successful login attempt(s) in last 30 day(s): 4 ----------------------------------------------------------------------------------------------------------------------------------User: admin1 Last login time: 12:49:19 UTC Tue Mar 22 2016 Last login location: Line vty0 ( 10.16.127.
PAGE 61
Limit Concurrent Login Sessions Dell Networking OS enables you to limit the number of concurrent login sessions of users on VTY, auxiliary, and console lines. You can also clear any of your existing sessions when you reach the maximum permitted number of concurrent sessions. By default, you can use all 10 VTY lines, one console line, and one auxiliary line.
PAGE 62
When you try to create more than the permitted number of sessions, the following message appears, prompting you to close one of the existing sessions. If you close any of the existing sessions, you are allowed to login. $ telnet 10.11.178.17 Trying 10.11.178.17... Connected to 10.11.178.17. Escape character is '^]'. Login: admin Password: Maximum concurrent sessions for the user reached. Current sessions for user admin: Line Location 2 vty 0 10.14.1.97 3 vty 1 10.14.1.97 4 vty 2 10.14.1.97 5 vty 3 10.14.1.
PAGE 63
• no logging buffer Disable logging to terminal lines. • CONFIGURATION mode no logging monitor Disable console logging. CONFIGURATION mode no logging console Sending System Messages to a Syslog Server To send system messages to a specified syslog server, use the following command. The following syslog standards are supported: RFC 5424 The SYSLOG Protocol, R.Gerhards and Adiscon GmbH, March 2009, obsoletes RFC 3164 and RFC 5426 Transmission of Syslog Messages over UDP.
PAGE 64
Jan 21 03:02:51: the full speed Jan 21 03:02:51: speed Jan 21 02:56:54: Jan 21 02:56:54: --More-- %SYSTEM:LP %CHMGR-2-PSU_FAN_SPEED_CHANGE: PSU_Fan speed changed to 80 % of %SYSTEM:LP %CHMGR-2-FAN_SPEED_CHANGE: Fan speed changed to 50 % of the full %SYSTEM:CP %SNMP-6-SNMP_WARM_START: Agent Initialized - SNMP WARM_START.
PAGE 65
• • • • • • • • • • • • • • • • • • • • • • • cron (for system scheduler messages) daemon (for system daemons) kern (for kernel messages) local0 (for local use) local1 (for local use) local2 (for local use) local3 (for local use) local4 (for local use) local5 (for local use) local6 (for local use) local7 (for local use) lpr (for line printer system messages) mail (for mail system messages) news (for USENET news messages) sys9 (system use) sys10 (system use) sys11 (system use) sys12 (system use) sys13 (syst
PAGE 66
• • level severity-level: the range is from 0 to 7. The default is 2. Use the all keyword to include all messages. limit: the range is from 20 to 300. The default is 20. To view the logging synchronous configuration, use the show config command in LINE mode. Enabling Timestamp on Syslog Messages By default, syslog messages include a time/date stamp, taken from the datetime, stating when the error or message was created. To enable timestamp, use the following command. • Add timestamp to syslog messages.
PAGE 67
[May 17 15:53:36]: CMD-(CLI):[write memory]by default from console - Repeated 5 times.
PAGE 68
• Specify the directory for users using FTP to reach the system. CONFIGURATION mode ftp-server topdir dir • The default is the internal flash directory. Specify a user name for all FTP users and configure either a plain text or encrypted password. CONFIGURATION mode ftp-server username username password [encryption-type] password Configure the following optional and required parameters: • • • username: enter a text string. encryption-type: enter 0 for plain text or 7 for encrypted text.
PAGE 69
ip access-class access-list To view the configuration, use the show config command in LINE mode. Dell(config-std-nacl)#show config ! ip access-list standard myvtyacl seq 5 permit host 10.11.0.1 Dell(config-std-nacl)#line vty 0 Dell(config-line-vty)#show config line vty 0 access-class myvtyacl Configuring Login Authentication for Terminal Lines You can use any combination of up to six authentication methods to authenticate a user on a terminal line.
PAGE 70
Setting Time Out of EXEC Privilege Mode EXEC time-out is a basic security feature that returns the system to EXEC mode after a period of inactivity on the terminal lines. To set time out, use the following commands. • Set the number of minutes and seconds. The default is 10 minutes on the console and 30 minutes on VTY. Disable EXEC time out by setting the time-out period to 0. LINE mode exec-timeout minutes [seconds] Return to the default time-out values.
PAGE 71
• • Set auto-lock using the configuration mode exclusive auto command from CONFIGURATION mode. When you set autolock, every time a user is in CONFIGURATION mode, all other users are denied access. This means that you can exit to EXEC Privilege mode, and re-enter CONFIGURATION mode without having to set the lock again. Set manual lock using the configure terminal lock command from CONFIGURATION mode.
PAGE 72
Syntax enable cpu-clock-monitor To disable this feature, use the no enable cpu-clock-monitor command. Parameters None Defaults Enabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.11(2.0) Introduced on the C9010, S3048–ON, S6100–ON and Z9100–ON.
PAGE 73
Ignoring the Startup Configuration and Booting from the Factory-Default Configuration If you do not want to do not want to boot up with your current startup configuration and do not want to delete it, you can interrupt the boot process and boot up with the C9000 series factory-default configuration. To boot up with the factory-default configuration: 1. Log onto the system using the console. 2. Power-cycle the chassis by disconnecting and then reconnecting the power cord. 3.
PAGE 74
The following example shows how the restore factory-defaults command restores a switch to its factory default settings. Dell# restore factory-defaults chassis nvram *********************************************************************** * Warning - Restoring factory defaults will delete the existing * * persistent settings (stacking, fanout, etc.) * * After restoration the unit(s) will be powercycled immediately.
PAGE 75
To boot from flash partition B: BOOT_USER # boot change primary boot device : file name : BOOT_USER # flash systemb To boot from the network: BOOT_USER # boot change primary boot device : file name : Server IP address : BOOT_USER # tftp FTOS-SI-9-5-0-169.bin 10.16.127.35 4. Assign an IP address and network mask to the Management Ethernet interface. BOOT_USER # interface management ethernet ip address ip_address_with_mask For example, 10.16.150.106/16. 5.
PAGE 76
MD5 Dell# verify md5 flash://FTOS-SE-9.5.0.0.bin MD5 hash for FTOS-SE-9.5.0.0.bin: 275ceb73a4f3118e1d6bcf7d75753459 SHA256 Dell# verify sha256 flash://FTOS-SE-9.5.0.0.bin SHA256 hash for FTOS-SE-9.5.0.0.bin: e6328c06faf814e6899ceead219afbf9360e986d692988023b749e6b2093e933 Examples: Entering the Hash Value for Verification MD5 Dell# verify md5 flash://FTOS-SE-9.5.0.0.bin 275ceb73a4f3118e1d6bcf7d75753459 MD5 hash VERIFIED for FTOS-SE-9.5.0.0.bin SHA256 Dell# verify sha256 flash://FTOS-SE-9.5.0.0.
PAGE 77
linecard 10 linecard 11 FLASH BOOT FLASH BOOT 1-0(0-4243)[boot] 1-0(0-4243)[boot] 1-0(0-4226) 1-0(0-4226) When System Images on C9010 Components Do Not Match You normally upgrade system images on all installed components at the same time by entering the upgrade system-image all command; for example: upgrade system-image all flash://FTOS-C9000-9.9.0.0.bin {A: | B:} command. For information about this upgrade procedure, see the C9010 and C1048P Release Notes.
PAGE 78
• To log in to a line-card processor: Hold down the Ctrl key and type geo. Then release the Ctrl key and type the line-card slot number 0 to 9. When you finish, log back in to the RPM CP: Hold down the Ctrl key and type geo. Then release the Ctrl key and type x. • Booting the C9010 from an Image on a Network Server If you can configure an RPM to boot from a system image stored on a network server, all C9010 components are automatically configured to boot from the RPM CP image.
PAGE 79
PRIMARY OPERATING SYSTEM BOOT PARAMETERS: ======================================== boot device : ftp file name : force10/rd/tgtimg/runtime/LP.bin Management Etherenet IP address : 127.10.10.43 Mask : 255.240.0.0 Server IP address : 127.10.10.10 Default Gateway IP address : 127.10.10.10 username : f10agent password : imagereq Viewing the Reason for Last System Reboot You can view the reason for the last system reboot.
PAGE 80
5 802.1X 802.1X is a method of port security. A device connected to a port that is enabled with 802.1X is disallowed from sending or receiving packets on the network until its identity can be verified (through a username and password, for example). This feature is named for its IEEE specification. 802.
PAGE 81
Figure 3. EAP Frames Encapsulated in Ethernet and RADUIS The authentication process involves three devices: • • • The device attempting to access the network is the supplicant. The supplicant is not allowed to communicate on the network until the authenticator authorizes the port. It can only communicate with the authenticator in response to 802.1X requests. The device with which the supplicant communicates is the authenticator. The authenticator is the gate keeper of the network.
PAGE 82
The Port-Authentication Process The authentication process begins when the authenticator senses that a link status has changed from down to up: 1. When the authenticator senses a link state change, it requests that the supplicant identify itself using an EAP Identity Request frame. 2. The supplicant responds with its identity in an EAP Response Identity frame. 3.
PAGE 83
Figure 5. EAP Over RADIUS RADIUS Attributes for 802.1 Support Dell Networking systems include the following RADIUS attributes in all 802.1X-triggered Access-Request messages: Attribute 31 Calling-station-id: relays the supplicant MAC address to the authentication server. Attribute 41 NAS-Port-Type: NAS-port physical port type. 15 indicates Ethernet. Attribute 61 NAS-Port: the physical port number by which the authenticator is connected to the supplicant.
PAGE 84
Enabling 802.1X Enable 802.1X globally. Figure 6. 802.1X Enabled 1. Enable 802.1X globally. CONFIGURATION mode dot1x authentication 2. Enter INTERFACE mode on an interface or a range of interfaces. INTERFACE mode interface [range] 3. Enable 802.1X on the supplicant interface only. INTERFACE mode dot1x authentication NOTE: You must enabled dot1x authentication globaly as well as in interface mode on which supplicant is connected. Verify that 802.
PAGE 85
interface TenGigabitEthernet 2/1 no ip address dot1x authentication no shutdown ! Dell# View 802.1X configuration information for an interface using the show dot1x interface command. The bold lines show that 802.1X is enabled on all ports unauthorized by default. Dell#show dot1x interface TenGigabitEthernet 2/1 802.
PAGE 86
203 Multicasts, 0 Broadcasts, 10760802177 Unicasts 0 runts, 0 giants, 0 throttles 0 CRC, 0 overrun, 0 discarded Output Statistics: 2285 packets, 146240 bytes, 0 underruns 2285 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts 0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts 1983 Multicasts, 0 Broadcasts, 302 Unicasts 0 throttles, 0 discarded, 0 collisions, 0 wreddrops Rate info (interval 299 seconds): Input 76.00 Mbits/sec, 149280 packets/sec, 10.00% of line-rate Output 00.
PAGE 87
Configuring the Static MAB and MAB Profile Enable MAB (mac-auth-bypass) before using the dot1x static-mab command to enable static mab. To enable static MAB and configure a static MAB profile, use the following commands. • Configure static MAB and static MAB profile on dot1x interface. INTERFACE mode dot1x static-mab profile profile-name Eenter a name to configure the static MAB profile name. The profile name length is limited to a maximum of 32 characters.
PAGE 88
switchport dot1x critical-vlan 300 no shutdown Dell#show dot1x interface tengigabitethernet 2/1 802.
PAGE 89
Configuring a Quiet Period after a Failed Authentication If the supplicant fails the authentication process, the authenticator sends another Request Identity frame after 30 seconds by default, but you can configure this period. NOTE: The quiet period (dot1x quiet-period) is a transmit interval for after a failed authentication; the Request Identity Re-transmit interval (dot1x tx-period) is for an unresponsive supplicant. To configure a quiet period, use the following command.
PAGE 90
The example shows configuration information for a port that has been force-authorized. The bold line shows the new port-control state. Dell(conf-if-Te-0/0)#dot1x port-control force-authorized Dell(conf-if-Te-0/0)#show dot1x interface TenGigabitEthernet 0/0 802.
PAGE 91
Re-Auth Interval: 7200 seconds Max-EAP-Req: 10 Auth Type: SINGLE_HOST Auth PAE State: Initialize Backend State: Initialize Auth PAE State: Initialize Backend State: Initialize Configuring Dynamic VLAN Assignment with Port Authentication On the switch, 802.1X authentication supports dynamic VLAN assignment. The basis for VLAN assignment is RADIUS attribute 81, Tunnel-Private-Group-ID. Dynamic VLAN assignment uses the standard dot1x procedure: 1. The host sends a dot1x packet to the Dell Networking system 2.
PAGE 92
4. Connect the supplicant to the port configured for 802.1X. 5. Verify that the port has been authorized and placed in the desired VLAN (refer to the illustration in Dynamic VLAN Assignment with Port Authentication). Guest and Authentication-Fail VLANs Typically, the authenticator (the Dell system) denies the supplicant access to the network until the supplicant is authenticated.
PAGE 93
Re-Auth Interval: Max-EAP-Req: Auth Type: Auth PAE State: Backend State: 7200 seconds 10 SINGLE_HOST Initialize Initialize Configuring an Authentication-Fail VLAN If the supplicant fails authentication, the authenticator re-attempts to authenticate after a specified amount of time. NOTE: For more information about authenticator re-attempts, refer to Configuring a Quiet Period after a Failed Authentication.
PAGE 94
Example of Viewing Configured Authentication 802.
PAGE 95
Supplicant Timeout: 15 seconds Server Timeout: 15 seconds Re-Auth Interval: 7200 seconds Max-EAP-Req: 10 Auth Type: Auth PAE State: Backend State: SINGLE_HOST Initialize Initialize Enter the tasks the user should do after finishing this task (optional). Multi-Host Authentication By default, 802.1x assumes that a single end user is connected to a single authenticator port in a one-to-one mode of authentication called single-host mode.
PAGE 96
Figure 9. Multi-Host Authentication Mode When you configure multi-host mode authentication, the first client to respond to an identity request is authenticated and subsequent responses are still ignored. However, because the authenticator expects the possibility of multiple responses, no system log is generated. After the first supplicant is authenticated, all end users connected to the authorized port are allowed to access the network.
PAGE 97
Auth-Fail VLAN id: Auth-Fail Max-Attempts: Critical VLAN: Critical VLAN id: Mac-Auth-Bypass: Mac-Auth-Bypass Only: Static-MAB: Static-MAB Profile: Tx Period: Quiet Period: ReAuth Max: Supplicant Timeout: Server Timeout: Re-Auth Interval: Max-EAP-Req: Host Mode: Auth PAE State: Backend State: NONE NONE Disable NONE Disable Disable Disable NONE 30 seconds 60 seconds 2 30 seconds 30 seconds 3600 seconds 2 MULTI_HOST Connecting Idle Configuring Single-Host Authentication To enable single-host authentication o
PAGE 98
During the authentication process, the switch is able to learn the MAC address of the device though the EAPoL frames, and the VLAN assignment from the RADIUS server. With this information it creates an authorized-MAC-to-VLAN mapping table per port. Then, the system can tag all incoming untagged frames with the appropriate VLAN-ID based on the table entries.
PAGE 99
MAC Authentication Bypass MAC authentication bypass (MAB) enables you to provide MAC-based security by allowing only known MAC addresses within the network using a RADIUS server. 802.1X-enabled clients can authenticate themselves using the 802.1X protocol. Other devices that do not use 802.1X — like IP phones, printers, and IP fax machines — still need connectivity to the network. The guest VLAN provides one way to access the network.
PAGE 100
• • • • Attribute 5—NAS -Port: The port number of the interface being authorized entered as an integer. Attribute 30—Called-Station-Id: MAC address of the ingress interfaces of the authenticator. Attribute 31—Calling-Station-Id: MAC address of the 802.1X supplicant. Attribute 87—NAS-Port-Id: The name of the interface being authorized entered as a string. NOTE: Only attributes 1 and 2 are used for MAB; Attributes 30 and 31 are not mandatory in the MAB method. 2.
PAGE 101
You can use dynamic CoS with 802.1X is when the traffic from a server should be classified based on the application that it is running. A static dot1p priority configuration applied from the switch is not sufficient in this case, as the server application might change. You would instead need to push the CoS configuration to the switches based on the application the server is running. Dynamic CoS uses RADIUS attribute 59, called User-Priority-Table, to specify the priority value for incoming frames.
PAGE 102
6 Access Control Lists (ACLs) This chapter describes access control lists (ACLs), prefix lists, and route-maps. • Access control lists (ACLs), Ingress IP and MAC ACLs , and Egress IP and MAC ACLs are supported on the system. At their simplest, access control lists (ACLs), prefix lists, and route-maps permit or deny traffic based on MAC and/or IP addresses. This chapter describes implementing IP ACLs, IP prefix lists and route-maps. For MAC ACLS, refer to Layer 2.
PAGE 103
When creating an access list, the sequence of the filters is important. You have a choice of assigning sequence numbers to the filters as you enter them, or the system assigns numbers in the order the filters are created. The sequence numbers are listed in the display output of the show config and show ip accounting access-list commands. Ingress and egress Hot Lock ACLs allow you to append or delete new rules into an existing ACL (already written into CAM) without disrupting traffic flow.
PAGE 104
DELL#test cam-usage service-policy input L3 pe-unit 0 stack-unit 0 port-set 0 PE Unit|Stack-unit|Portpipe|CAM Partition|Available CAM|Estimated CAM per Port|Status ------------------------------------------------------------------------------------0 | 0 | 0 | L3QOS | 488 0 | Allowed User-Configurable CAM Allocation User-configurable content-addressable memory (CAM) allows you to specify the amount of memory space that you want to allocate for ACLs.
PAGE 105
2. Verify the new settings that will be written to CAM on the next reload. The CAM ACL ingress profiles are configured globally on the PE. The show cam-acl-pe command does not display CAM ACL ingress profiles for each PE. The new settings will be written to CAM on the next reload EXEC and EXEC Privilege mode show cam-acl-pe 3. Reload the system. EXEC Privilege mode reload The following example displays the current CAM ACL settings for each ingress region and configures the ingress CAM settings.
PAGE 106
3. Reload the system. EXEC Privilege mode reload The following example displays the current CAM ACL settings for each egress region and configures the egress CAM settings. Dell# show cam-acl-egress-pe -- Port extender Egress Cam ACL -Current Settings(in block sizes) 1 block = 256 entries L2Acl : 1 Ipv4Acl : 1 Ipv6Acl : 2 Dell(conf)#cam-acl-egress-pe l2acl 2 ipv4acl 2 ipv6acl 0 The following example displays the running configuration for the configured CAM ACLs.
PAGE 107
Determine the Order in which ACLs are Used to Classify Traffic When you link class-maps to queues using the service-queue command, the system matches the class-maps according to queue priority (queue numbers closer to 0 have lower priorities). As shown in the following example, class-map cmap2 is matched against ingress packets before cmap1. ACLs acl1 and acl2 have overlapping rules because the address range 20.1.1.0/24 is within 20.0.0.0/8.
PAGE 108
Optimizing ACL for More Number of IPv4 ACL Rules To optimize ACL for more number of IPv4 ACL rules, follow these steps: 1. Carve the vlanaclopt CAM region. CONFIGURATION mode cam-acl-vlan vlanopenflow 0 vlaniscsi 0 vlanaclopt 2 2. Enable the ACL optimized feature. CONFIGURATION mode feature acloptimized 3. Reload the system EXEC Privilege reload After the system reloads, the Dell Networking OS enables the feature.
PAGE 109
Example of Denying Second and Subsequent Fragments Dell(conf)#ip access-list extended ABC Dell(conf-ext-nacl)#deny ip any 10.1.1.1/32 fragments Dell(conf-ext-nacl)#permit ip any 10.1.1.1/32 Dell(conf-ext-nacl) Layer 4 ACL Rules Examples The following examples show the ACL commands for Layer 4 packet filtering. Permit an ACL line with L3 information only, and the fragments keyword is present: If a packet’s L3 information matches the L3 information in the ACL line, the packet's FO is checked.
PAGE 110
Configure a Standard IP ACL To configure an ACL, use commands in IP ACCESS LIST mode and INTERFACE mode. For a complete list of all the commands related to IP ACLs, refer to the Dell Networking OS Command Line Interface Reference Guide. To set up extended ACLs, refer to Configure an Extended IP ACL. A standard IP ACL uses the source IP address as its match criterion. 1. Enter IP ACCESS LIST mode by naming a standard IP access list. CONFIGURATION mode ip access-list standard access-listname 2.
PAGE 111
{deny | permit} {source [mask] | any | host ip-address} [count [byte]] [order] [fragments] When you use the log keyword, the CP logs details about the packets that match. Depending on how many packets match the log entry and at what rate, the CP may become busy as it has to log these packets’ details. The following example shows a standard IP ACL in which the system assigns the sequence numbers.
PAGE 112
CONFIGURATION mode ip access-list extended access-list-name 2. Configure an extended IP ACL filter for TCP packets. CONFIG-EXT-NACL mode seq sequence-number {deny | permit} tcp {source mask | any | host ip-address}} [count [byte]] [order] [fragments] Configure Filters, UDP Packets To create a filter for UDP packets with a specified sequence number, use the following commands. 1. Create an extended IP ACL and assign it a unique name. CONFIGURATION mode ip access-list extended access-list-name 2.
PAGE 113
The following example shows an extended IP ACL in which the sequence numbers were assigned by the software. The filters were assigned sequence numbers based on the order in which they were configured (for example, the first filter was given the lowest sequence number). The show config command in IP ACCESS LIST mode displays the two filters with the sequence numbers 5 and 10. Dell(config-ext-nacl)#deny tcp host 123.55.34.0 any Dell(config-ext-nacl)#permit udp 154.44.123.34 0.0.255.255 host 34.6.0.
PAGE 114
Guidelines for Configuring ACL VLAN Groups Keep the following points in mind when you configure ACL VLAN groups: • • • • • • • • • • The VLAN member interfaces, on which the ACL in an ACL VLAN group is applied, function as restricted interfaces. The ACL VLAN group name identifies the group of VLANs on which hierarchical filtering is performed. You can add only one ACL to an interface at a time.
PAGE 115
Vlan Members : 2-10,99 Group Name : HostGroup Vlan Members : 1,1000 Dell# Allocating ACL VLAN CAM CAM optimization for ACL VLAN groups is not enabled by default. You must allocate blocks of ACL VLAN CAM to enable ACL CAM optimization by using the cam-acl-vlan command. By default, 0 blocks of CAM are allocated for VLAN services in the VLAN Content Aware Processor (VCAP), an application that modifies VLAN settings before forwarding packets on member interfaces.
PAGE 116
Applying Ingress ACLs on the Port Extender Ingress ACLs are applied to port extender interfaces and to traffic entering the system. These system-wide ACLs eliminate the need to apply ACLs onto each interface and achieves the same results. By localizing target traffic, it is a simpler implementation. To create an ingress ACL, use the ip access-group command in EXEC Privilege mode. The example shows applying the ACL, rules to the newly created access group, and viewing the access list.
PAGE 117
Dell#show ip accounting access-list ! Extended Ingress IP access list abcd on gigethernet 0/0 seq 5 permit tcp any any seq 10 deny icmp any any seq 15 permit 1.1.1.2 Applying Layer 3 Egress ACLs on Control-Plane Traffic By default, packets originated from the system are not filtered by egress ACLs. For example, if you initiate a ping session from the system and apply an egress ACL to block this type of traffic on the interface, the ACL does not affect that ping traffic.
PAGE 118
The following rules apply to prefix lists: • • A prefix list without any permit or deny filters allows all routes. An “implicit deny” is assumed (that is, the route is dropped) for all route prefixes that do not match a permit or deny filter in a configured prefix list. After a route matches a filter, the filter’s action is applied. No additional filters are applied to the route.
PAGE 119
If you are creating a standard prefix list with only one or two filters, you can let the system assign a sequence number based on the order in which the filters are configured. The system assigns filters in multiples of five. Creating a Prefix List Without a Sequence Number To create a filter without a specified sequence number, use the following commands. 1. Create a prefix list and assign it a unique name. CONFIGURATION mode ip prefix-list prefix-name 2.
PAGE 120
ip prefix-list filter_in: count: 3, range entries: 3, sequences: 5 - 10 ip prefix-list filter_ospf: count: 4, range entries: 1, sequences: 5 - 10 Dell> Applying a Prefix List for Route Redistribution To pass traffic through a configured prefix list, use the prefix list in a route redistribution command. Apply the prefix list to all traffic redistributed into the routing process. The traffic is either forwarded or dropped, depending on the criteria and actions specified in the prefix list.
PAGE 121
ACL Remarks While defining ACL rules, you can optionally include a remark to make the ACLs more descriptive. You can include a remark with a maximum of 80 characters in length. The remark command is available in each ACL mode. You can configure up to 4294967291 remarks for a given IP ACL and 65536 remarks for a given MAC ACL. You can include a remark with or without a remark number. If you do not enter a remark number, the remark inherits the sequence number of the last ACL rule.
PAGE 122
seq 10 permit ip any any Dell(config-ext-nacl)#no remark 10 Dell(config-ext-nacl)#show config ! ip access-list extended test seq 10 permit ip any any ACL Resequencing ACL resequencing allows you to re-number the rules and remarks in an access or prefix list. The placement of rules within the list is critical because packets are matched against rules in sequential order. To order new rules using the current numbering scheme, use resequencing whenever there is no opportunity.
PAGE 123
remark 4 XYZ remark 5 this remark corresponds to permit any host 1.1.1.1 seq 5 permit ip any host 1.1.1.1 remark 9 ABC remark 10 this remark corresponds to permit ip any host 1.1.1.2 seq 10 permit ip any host 1.1.1.2 seq 15 permit ip any host 1.1.1.3 seq 20 permit ip any host 1.1.1.4 Dell# end Dell# resequence access-list ipv4 test 2 2 Dell# show running-config acl ! ip access-list extended test remark 2 XYZ remark 4 this remark corresponds to permit any host 1.1.1.1 seq 4 permit ip any host 1.1.1.
PAGE 124
Important Points to Remember • For route-maps with more than one match clause: • Two or more match clauses within the same route-map sequence have the same match commands (though the values are different), matching a packet against these clauses is a logical OR operation. • Two or more match clauses within the same route-map sequence have different match commands, matching a packet against these clauses is a logical AND operation.
PAGE 125
tag 35 level stub-area Dell# To delete all instances of that route map, use the no route-map map-name command. To delete just one instance, add the sequence number to the command syntax. Dell(conf)#no route-map zakho 10 Dell(conf)#end Dell#show route-map route-map zakho, permit, sequence 20 Match clauses: interface TengigabitEthernet 0/1 Set clauses: tag 35 level stub-area Dell# The following example shows a route map with multiple instances.
PAGE 126
Example of the match Command to Permit and Deny Routes Dell(conf)#route-map force permit 10 Dell(config-route-map)#match tag 1000 Dell(conf)#route-map force deny 20 Dell(config-route-map)#match tag 1000 Dell(conf)#route-map force deny 30 Dell(config-route-map)#match tag 1000 Configuring Match Routes To configure match criterion for a route map, use the following commands. • Match routes with the same AS-PATH numbers.
PAGE 127
• Match routes specified as internal or external to OSPF, ISIS level-1, ISIS level-2, or locally generated. • CONFIG-ROUTE-MAP mode match route-type {external [type-1 | type-2] | internal | level-1 | level-2 | local } Match routes with a specific tag. CONFIG-ROUTE-MAP mode match tag tag-value To create route map instances, use these commands. There is no limit to the number of match commands per route map, but the convention is to keep the number of match filters in a route map low.
PAGE 128
Configure a Route Map for Route Redistribution Route maps on their own cannot affect traffic and must be included in different commands to affect routing traffic. Route redistribution occurs when the system learns the advertising routes from static or directly connected routes or another routing protocol. Different protocols assign different values to redistributed routes to identify either the routes and their origins.
PAGE 129
set as-path prepend 1 2 3 4 5 continue 30! Configuring a UDF ACL To configure a User Defined Field (UDF) ACL: 1. Enable the UDF ACL feature on a switch. CONFIGURATION mode feature udf-acl Dell(conf)#feature udf-acl 2. Change the default CAM allocation or reconfigure new CAM allocation settings and enable IPV4 UDF.
PAGE 130
udf-tcam ipnip seq 1 match l2ethertype ipv4 ipprotocol 4 vlantag any Dell(conf-udf-tcam)# 9. Create a UDF qualifier to assign values to UDF IDs. CONFIGURATION-UDF TCAM mode udf-qualifier-value name Dell(conf-udf-tcam)# udf-qualifier-value ipnip_val1 10. Assign a value to a UDF ID. CONFIGURATION-UDF-Qualifier-Value Profile mode udf-id 1-12 value mask Dell(conf-udf-tcam-qual-val)#udf-id 1 aa ff 11. Associate the UDF qualifier value with a UDF packet profile in an IP access list.
PAGE 131
7 Bidirectional Forwarding Detection (BFD) BFD is a protocol that is used to rapidly detect communication failures between two adjacent systems. It is a simple and lightweight replacement for existing routing protocol link state detection mechanisms. It also provides a failure detection solution for links on which no routing protocol is used. BFD is a simple hello mechanism. Two neighboring systems running BFD establish a session using a three-way handshake.
PAGE 132
BFD Packet Format Control packets are encapsulated in user datagram protocol (UDP) packets. The following illustration shows the complete encapsulation of a BFD control packet inside an IPv4 packet. Figure 10. BFD in IPv4 Packet Format Field Description Diagnostic Code The reason that the last session failed. State The current local session state. Refer to BFD Sessions. Flag A bit that indicates packet function.
PAGE 133
Field Description Your Discriminator A random number generated by the remote system to identify the session. Discriminator values are necessary to identify the session to which a control packet belongs because there can be many sessions running on a single interface. Desired Min TX Interval The minimum rate at which the local system would like to send control packets to the remote system.
PAGE 134
The session is declared down if: • • • A control packet is not received within the detection time. Sufficient echo packets are lost. Demand mode is active and a control packet is not received in response to a poll packet. BFD Three-Way Handshake A three-way handshake must take place between the systems that participate in the BFD session.
PAGE 135
Session State Changes The following illustration shows how the session state on a system changes based on the status notification it receives from the remote system. For example, if a session on a system is down and it receives a Down status notification from the remote system, the session state on the local system changes to Init. Figure 12.
PAGE 136
Configure BFD for Physical Ports Configuring BFD for physical ports is supported on the C-Series and E-Series platforms only. BFD on physical ports is useful when you do not enable the routing protocol. Without BFD, if the remote system fails, the local system does not remove the connected route until the first failed attempt to send a packet. When you enable BFD, the local system removes the route as soon as it stops receiving periodic control packets from the remote system.
PAGE 137
Uptime: 00:09:06 Statistics: Number of packets received from neighbor: 4092 Number of packets sent to neighbor: 4093 Number of state changes: 1 Number of messages from IFA about port state change: 0 Number of messages communicated b/w Manager and Agent: 7 Disabling and Re-Enabling BFD BFD is enabled on all interfaces by default, though sessions are not created unless explicitly configured.
PAGE 138
Establishing Sessions for Static Routes Sessions are established for all neighbors that are the next hop of a static route. Figure 13. Establishing Sessions for Static Routes To establish a BFD session, use the following command. • Establish BFD sessions for all neighbors that are the next hop of a static route. CONFIGURATION mode ip route bfd To verify that sessions have been created for static routes, use the show bfd neighbors command. R1(conf)#ip route 2.2.3.0/24 2.2.2.
PAGE 139
ip route bfd vrf vrf2 ip route bfd vrf vrf1 prefix-list p4_le The following example shows that sessions are created for static routes for the default VRF. The following example shows that sessions are created for static routes for the nondefault VRFs. Establishing Static Route Sessions on Specific Neighbors You can selectively enable BFD sessions on specific neighbors based on a destination prefix-list.
PAGE 140
Disabling BFD for Static Routes If you disable BFD, all static route BFD sessions are torn down. A final Admin Down packet is sent to all neighbors on the remote systems, and those neighbors change to the Down state. To disable BFD for static routes, use the following command. • Disable BFD for static routes. CONFIGURATION mode no ip route bfd Configure BFD for IPv6 Static Routes BFD offers systems a link state detection mechanism for static routes.
PAGE 141
Changing IPv6 Static Route Session Parameters BFD sessions are configured with default intervals and a default role. The parameters you can configure are: Desired TX Interval, Required Min RX Interval, Detection Multiplier, and system role. These parameters are configured for all static routes. If you change a parameter, the change affects all sessions for static routes. To change parameters for static route sessions, use the following command . • Change parameters for all static route sessions.
PAGE 142
To view session parameters, use the show bfd neighbors detail command. Establishing Sessions with OSPF Neighbors BFD sessions can be established with all OSPF neighbors at once or sessions can be established with all neighbors out of a specific interface. Sessions are only established when the OSPF adjacency is in the Full state. Figure 14. Establishing Sessions with OSPF Neighbors To establish BFD with all OSPF neighbors or with OSPF neighbors on a single interface, use the following commands.
PAGE 143
Ad Dn - Admin Down C - CLI I - ISIS O - OSPF R - Static Route (RTM) LocalAddr RemoteAddr Interface State Rx-int Tx-int Mult Clients * 2.2.2.2 2.2.2.1 Te 2/1 Up 200 200 3 O * 2.2.3.1 2.2.3.2 Te 2/2 Up 200 200 3 O Establishing Sessions with OSPF Neighbors for nondefault VRFs To configure BFD in a nondefault VRF, follow this procedure: • Enable BFD globally. • CONFIGURATION mode bfd enable Establish sessions with all OSPF neighbors in a specific VRF.
PAGE 144
M V VT - MPLS - VRRP - Vxlan Tunnel LocalAddr * 5.1.1.1 RemoteAddr 5.1.1.2 Interface Po 30 State Rx-int Tx-int Mult VRF Clients Up 200 200 3 255 O * 6.1.1.1 6.1.1.2 Vl 30 Up 200 Dell# show bfd neighbors detail Session Discriminator: 1 Neighbor Discriminator: 1 Local Addr: 10.1.3.2 Local MAC Addr: 00:01:e8:02:15:0e Remote Addr: 10.1.3.
PAGE 145
State: Up Configured parameters: TX: 200ms, RX: 200ms, Multiplier: 3 Neighbor parameters: TX: 200ms, RX: 200ms, Multiplier: 3 Actual parameters: TX: 200ms, RX: 200ms, Multiplier: 3 Role: Active Delete session on Down: True VRF: VRF_blue Client Registered: OSPF Uptime: 00:00:15 Statistics: Number of packets received from neighbor: 78 Number of packets sent to neighbor: 78 Number of state changes: 1 Number of messages from IFA about port state change: 0 Number of messages communicated b/w Manager and Agent: 4
PAGE 146
• Change parameters for OSPFv3 sessions on a single interface. INTERFACE mode ipv6 ospf bfd all-neighbors interval milliseconds min_rx milliseconds multiplier value role [active | passive] Establishing BFD Sessions with OSPFv3 Neighbors for nondefault VRFs To configure BFD in a nondefault VRF, use the following procedure: • Enable BFD globally. • CONFIGURATION mode bfd enable Establish sessions with all OSPFv3 neighbors in a specific VRF.
PAGE 147
* fe80::2a0:c9ff:fe00:2 511 O3 fe80::3617:98ff:fe34:12 Vl 100 Up 150 150 3 * fe80::2a0:c9ff:fe00:2 511 O3 fe80::3617:98ff:fe34:12 Vl 101 Up 150 150 3 * fe80::2a0:c9ff:fe00:2 511 O3 fe80::3617:98ff:fe34:12 Vl 102 Up 150 150 3 * fe80::2a0:c9ff:fe00:2 511 O3 Dell# fe80::3617:98ff:fe34:12 Vl 103 Up 150 150 3 Disabling BFD for OSPFv3 If you disable BFD globally, all sessions are torn down and sessions on the remote system are placed in a Down state.
PAGE 148
Establishing Sessions with IS-IS Neighbors BFD sessions can be established for all IS-IS neighbors at once or sessions can be established for all neighbors out of a specific interface. Figure 15. Establishing Sessions with IS-IS Neighbors To establish BFD with all IS-IS neighbors or with IS-IS neighbors on a single interface, use the following commands. • Establish sessions with all IS-IS neighbors. • ROUTER-ISIS mode bfd all-neighbors Establish sessions with IS-IS neighbors on a single interface.
PAGE 149
Changing IS-IS Session Parameters BFD sessions are configured with default intervals and a default role. The parameters that you can configure are: Desired TX Interval, Required Min RX Interval, Detection Multiplier, and system role. These parameters are configured for all IS-IS sessions or all IS-IS sessions out of an interface. If you change a parameter globally, the change affects all IS-IS neighbors sessions.
PAGE 150
Figure 16. Establishing Sessions with BGP Neighbors The sample configuration shows alternative ways to establish a BFD session with a BGP neighbor: • • By establishing BFD sessions with all neighbors discovered by BGP (the bfd all-neighbors command). By establishing a BFD session with a specified BGP neighbor (the neighbor {ip-address | peer-group-name} bfd command) BFD packets originating from a router are assigned to the highest priority egress queue to minimize transmission delays.
PAGE 151
CONFIG-ROUTERBGP mode neighbor {ip-address | peer-group-name} no shutdown 5. Configure parameters for a BFD session established with all neighbors discovered by BGP. OR Establish a BFD session with a specified BGP neighbor or peer group using the default BFD session parameters.
PAGE 152
bfd all-neighbors DellEMC(conf)#router bgp 1 DellEMC(conf-router_bgp)#address-family ipv4 vrf vrf1 DellEMC(conf-router_bgp_af)#neighbor 10.1.1.2 remote-as 2 DellEMC(conf-router_bgp_af)#neighbor 10.1.1.
PAGE 153
show ip bgp neighbors [ip-address] The following example shows verifying a BGP configuration. R2# show running-config bgp ! router bgp 2 neighbor 1.1.1.2 remote-as 1 neighbor 1.1.1.2 no shutdown neighbor 2.2.2.2 remote-as 1 neighbor 2.2.2.2 no shutdown neighbor 3.3.3.2 remote-as 1 neighbor 3.3.3.2 no shutdown bfd all-neighbors The following example shows viewing all BFD neighbors. The following example shows viewing BFD neighbors with full detail.
PAGE 154
ROUTE_REFRESH(2) CISCO_ROUTE_REFRESH(128) Neighbor is using BGP global mode BFD configuration For address family: IPv4 Unicast BGP table version 0, neighbor version 0 Prefixes accepted 0 (consume 0 bytes), withdrawn 0 by peer, martian prefixes ignored 0 Prefixes advertised 0, denied 0, withdrawn 0 from peer Connections established 1; dropped 0 Last reset never Local host: 2.2.2.3, Local port: 63805 Foreign host: 2.2.2.2, Foreign port: 179 E1200i_ExaScale# R2# show ip bgp neighbors 2.2.2.3 BGP neighbor is 2.
PAGE 155
Establishing Sessions with All VRRP Neighbors BFD sessions can be established for all VRRP neighbors at once, or a session can be established with a particular neighbor. Figure 17. Establishing Sessions with All VRRP Neighbors To establish sessions with all VRRP neighbors, use the following command. • Establish sessions with all VRRP neighbors.
PAGE 156
LocalAddr RemoteAddr Interface State Rx-int Tx-int Mult Clients * 2.2.5.1 2.2.5.2 Te 4/25 Down 1000 1000 3 V To view session state information, use the show vrrp command. The following example shows viewing VRRP session state information. The bold line shows the VRRP BFD session. R1(conf-if-te-4/25)#do show vrrp -----------------TenGigabitEthernet 4/1, VRID: 1, Net: 2.2.5.1 State: Backup, Priority: 1, Master: 2.2.5.
PAGE 157
Configuring Protocol Liveness Protocol liveness is a feature that notifies the BFD manager when a client protocol is disabled. When you disable a client, all BFD sessions for that protocol are torn down. Neighbors on the remote system receive an Admin Down control packet and are placed in the Down state. To enable protocol liveness, use the following command. • Enable Protocol Liveness.
PAGE 158
8 Border Gateway Protocol IPv4 (BGPv4) This chapter provides a general description of BGPv4 as it is supported in the Dell Networking OS. BGP protocol standards are listed in the Standards Compliance chapter. BGP is an external gateway protocol that transmits interdomain routing information within and between autonomous systems (AS). The primary function of the BGP is to exchange network reachability information with other BGP systems.
PAGE 159
Figure 18. Interior BGP BGP version 4 (BGPv4) supports classless interdomain routing and aggregate routes and AS paths. BGP is a path vector protocol — a computer network in which BGP maintains the path that updated information takes as it diffuses through the network. Updates traveling through the network and returning to the same node are easily detected and discarded.
PAGE 160
Figure 19. BGP Routers in Full Mesh The number of BGP speakers each BGP peer must maintain increases exponentially. Network management quickly becomes impossible. Sessions and Peers When two routers communicate using the BGP protocol, a BGP session is started. The two end-points of that session are Peers. A Peer is also called a Neighbor. Establish a Session Information exchange between peers is driven by events and timers. The focus in BGP is on the traffic routing policies.
PAGE 161
State Description Connect In this state the router waits for the TCP connection to complete, transitioning to the OpenSent state if successful. If that transition is not successful, BGP resets the ConnectRetry timer and transitions to the Active state when the timer expires. Active The router resets the ConnectRetry timer to zero and returns to the Connect state. OpenSent After successful OpenSent transition, the router sends an Open message and waits for one in return.
PAGE 162
1. Router B receives an advertisement from Router A through eBGP. Because the route is learned through eBGP, Router B advertises it to all its iBGP peers: Routers C and D. 2. Router C receives the advertisement but does not advertise it to any peer because its only other peer is Router D, an iBGP peer, and Router D has already learned it through iBGP from Router B. 3.
PAGE 163
Figure 21. BGP Best Path Selection Best Path Selection Details 1. Prefer the path with the largest WEIGHT attribute. 2. Prefer the path with the largest LOCAL_PREF attribute. 3. Prefer the path that was locally Originated via a network command, redistribute command or aggregate-address command. a. Routes originated with the Originated via a network or redistribute commands are preferred over routes originated with the aggregate-address command. 4.
PAGE 164
a. if the Router-ID is the same for multiple paths (because the routes were received from the same route) skip this step. b. if the Router-ID is NOT the same for multiple paths, prefer the path that was first received as the Best Path. The path selection algorithm returns without performing any of the checks detailed here. 11. Prefer the external path originated from the BGP router with the lowest router ID. If both paths are external, prefer the oldest path (first received path).
PAGE 165
Multi-Exit Discriminators (MEDs) If two ASs connect in more than one place, a multi-exit discriminator (MED) can be used to assign a preference to a preferred path. MED is one of the criteria used to determine the best path, so keep in mind that other criteria may impact selection, as shown in the illustration in Best Path Selection Criteria. One AS assigns the MED a value and the other AS uses that value to decide the preferred path. For this example, assume the MED is the only attribute applied.
PAGE 166
*> 7.0.0.0/30 *> 9.2.0.0/16 10.114.8.33 10.114.8.33 0 10 0 0 18508 18508 ? 701 i AS Path The AS path is the list of all ASs that all the prefixes listed in the update have passed through. The local AS number is added by the BGP speaker when advertising to a eBGP neighbor. The AS path is shown in the following example. The origin attribute is shown following the AS path information (shown in bold).
PAGE 167
Implement BGP The following sections describe how BGP is implemented on the switch. Additional Path (Add-Path) Support The add-path feature reduces convergence times by advertising multiple paths to its peers for the same address prefix without replacing existing paths with new ones. By default, a BGP speaker advertises only the best path to its peers for a given address prefix. If the best path becomes unavailable, the BGP speaker withdraws its path from its local RIB and recalculates a new best path.
PAGE 168
Where the 2-Byte format is 1-65535, the 4-Byte format is 1-4294967295. Enter AS numbers using the traditional format. If the ASN is greater than 65535, the dot format is shown when using the show ip bgp commands. For example, an ASN entered as 3183856184 appears in the show commands as 48581.51768; an ASN of 65123 is shown as 65123. To calculate the comparable dot format for an ASN from a traditional format, use ASN/65536. ASN%65536. Traditional Format DOT Format 65001 0.65501 65536 1.0 100000 1.
PAGE 169
Dell(conf-router_bgp)#bgp asnotation asdot+ Dell(conf-router_bgp)#show conf ! router bgp 100 bgp asnotation asdot+ bgp four-octet-as-support neighbor 172.30.1.250 local-as 65057 Dell(conf-router_bgp)#do show ip bgp BGP table version is 31571, local router ID is 172.30.1.57 AS-PLAIN Dell(conf-router_bgp)#bgp asnotation asplain Dell(conf-router_bgp)#sho conf ! router bgp 100 bgp four-octet-as-support neighbor 172.30.1.
PAGE 170
Figure 24. Before and After AS Number Migration with Local-AS Enabled When you complete your migration, and you have reconfigured your network with the new information, disable this feature. If you use the “no prepend” option, the Local-AS does not prepend to the updates received from the eBGP peer. If you do not select “no prepend” (the default), the Local-AS is added to the first AS segment in the AS-PATH.
PAGE 171
Important Points to Remember • • • • • • • • • • • • • • • • • • • • • • • Because eBGP packets are not controlled by the ACL, packets from BGP neighbors cannot be blocked using the deny ip command. The f10BgpM2AsPathTableEntry table, f10BgpM2AsPathSegmentIndex, and f10BgpM2AsPathElementIndex are used to retrieve a particular ASN from the AS path. These indices are assigned to the AS segments and individual ASN in each segment starting from 0.
PAGE 172
• • auto-summarization (the default is no auto-summary) synchronization (the default is no synchronization) BGP Configuration To enable the BGP process and begin exchanging information, assign an AS number and use commands in ROUTER BGP mode to configure a BGP neighbor. By default, BGP is disabled. By default, the system compares the MED attribute on different paths from within the same AS (the bgp always-compare-med command is not enabled).
PAGE 173
CONFIGURATION mode router bgp as-number • as-number: from 0 to 65535 (2 Byte) or from 1 to 4294967295 (4 Byte) or 0.1 to 65535.65535 (Dotted format). Only one AS is supported per system. NOTE: If you enter a 4-Byte AS number, 4-Byte AS support is enabled automatically. a) Enable 4-Byte support for the BGP process. NOTE: This command is OPTIONAL. Enable if you want to use 4-Byte AS numbers or if you support AS4 number representation.
PAGE 174
192.168.12.2 65123 0 R2# 0 0 0 0 never Active R2#show ip bgp summary BGP router identifier 192.168.10.2, local AS number 48735.
PAGE 175
For address family: IPv4 Unicast BGP table version 0, neighbor version 0 0 accepted prefixes consume 0 bytes Prefix advertised 0, rejected 0, withdrawn 0 Connections established 0; dropped 0 Last reset never No active TCP connection Dell# The following example shows verifying the BGP configuration. R2#show running-config bgp ! router bgp 65123 bgp router-id 192.168.10.2 network 10.10.21.0/24 network 10.10.32.0/24 network 100.10.92.0/24 network 192.168.10.0/24 bgp four-octet-as-support neighbor 10.10.21.
PAGE 176
CONFIG-ROUTER-BGP mode bgp asnotation asdot+ The following example shows the bgp asnotation asplain command. Dell(conf-router_bgp)#bgp asnotation asplain Dell(conf-router_bgp)#sho conf ! router bgp 100 bgp four-octet-as-support neighbor 172.30.1.250 remote-as 18508 neighbor 172.30.1.250 local-as 65057 neighbor 172.30.1.250 route-map rmap1 in neighbor 172.30.1.250 password 7 5ab3eb9a15ed02ff4f0dfd4500d6017873cfd9a267c04957 neighbor 172.30.1.
PAGE 177
By default, all peer groups are disabled. 3. Create a BGP neighbor. CONFIG-ROUTERBGP mode neighbor ip-address remote-as as-number 4. Enable the neighbor. CONFIG-ROUTERBGP mode neighbor ip-address no shutdown 5. Add an enabled neighbor to the peer group. CONFIG-ROUTERBGP mode neighbor ip-address peer-group peer-group-name 6. Add a neighbor as a remote AS. CONFIG-ROUTERBGP mode neighbor {ip-address | peer-group name} remote-as as-number Formats: IP Address A.B.C.D • • Peer-Group Name: 16 characters.
PAGE 178
To enable a peer group, use the neighbor peer-group-name no shutdown command in CONFIGURATION ROUTER BGP mode (shown in bold). Dell(conf-router_bgp)#neighbor zanzibar no shutdown Dell(conf-router_bgp)#show config ! router bgp 45 bgp fast-external-fallover bgp log-neighbor-changes neighbor zanzibar peer-group neighbor zanzibar no shutdown neighbor 10.1.1.1 remote-as 65535 neighbor 10.1.1.1 shutdown neighbor 10.14.8.60 remote-as 18505 neighbor 10.14.8.
PAGE 179
When you enable fail-over, BGP tracks IP reachability to the peer remote address and the peer local address. Whenever either address becomes unreachable (for example, no active route exists in the routing table for peer IPv6 destinations/local address), BGP brings down the session with the peer. The BGP fast fail-over feature is configured on a per-neighbor or peer-group basis and is disabled by default. To enable the BGP fast fail-over feature, use the following command.
PAGE 180
Minimum time between advertisement runs is 5 seconds For address family: IPv4 Unicast BGP neighbor is test Number of peers in this group 1 Peer-group members (* - outbound optimized): 100.100.100.100* Dell# router bgp neighbor neighbor neighbor neighbor neighbor neighbor neighbor Dell# 65517 test peer-group test fail-over test no shutdown 100.100.100.100 remote-as 65517 100.100.100.100 fail-over 100.100.100.100 update-source Loopback 0 100.100.100.
PAGE 181
• • • Peer Group Name: 16 characters. AS-number: 0 to 65535 (2-Byte) or 1 to 4294967295 (4-Byte) or 0.1 to 65535.65535 (Dotted format). No Prepend: specifies that local AS values are not prepended to announcements from the neighbor. Format: IP Address: A.B.C.D. You must Configure Peer Groups before assigning it to an AS. This feature is not supported on passive peer groups. The first line in bold shows the actual AS number.
PAGE 182
neighbor 10.10.21.1 no shutdown neighbor 10.10.32.3 remote-as 65123 neighbor 10.10.32.3 no shutdown neighbor 100.10.92.9 remote-as 65192 neighbor 100.10.92.9 local-as 6500 neighbor 100.10.92.9 no shutdown neighbor 192.168.10.1 remote-as 65123 neighbor 192.168.10.1 update-source Loopback 0 neighbor 192.168.10.1 no shutdown neighbor 192.168.12.2 remote-as 65123 neighbor 192.168.12.2 allowas-in 9 neighbor 192.168.12.2 update-source Loopback 0 neighbor 192.168.12.
PAGE 183
0x59cd3b4 0x7128114 0x536a914 0x2ffe884 0x2ff7284 0x2ff7ec4 0x2ff8544 0x736c144 0x3b8d224 0x5eb1e44 0x5cd891c --More-- 0 0 0 0 0 0 0 0 0 0 0 2 10 3 1 99 4 3 1 10 1 9 18508 18508 18508 18508 18508 18508 18508 18508 18508 18508 18508 209 209 209 701 701 209 701 701 209 701 209 7018 15227 i 3356 13845 i 701 6347 7781 i 3561 9116 21350 i 1239 577 855 ? 3561 4755 17426 i 5743 2648 i 209 568 721 1494 i 701 2019 i 8584 16158 i 6453 4759 i Regular Expressions as Filters Regular expressions are used to filter
PAGE 184
Dell(conf-router_bgp)#neigh 10.155.15.2 filter-list 1 in Dell(conf-router_bgp)#ex Dell(conf)#ip as-path access-list Eagle Dell(config-as-path)#deny 32$ Dell(config-as-path)#ex Dell(conf)#router bgp 99 Dell(conf-router_bgp)#neighbor AAA filter-list Eagle in Dell(conf-router_bgp)#show conf ! router bgp 99 neighbor AAA peer-group neighbor AAA filter-list Eaglein neighbor AAA no shutdown neighbor 10.155.15.2 remote-as 32 neighbor 10.155.15.2 filter-list 1 in neighbor 10.155.15.
PAGE 185
1. Allow the advertisement of multiple paths for the same address prefix without the new paths replacing any previous ones. CONFIG-ROUTER-BGP mode bgp add-path {send | both} path-count count bgp add-path receive The range is from 2 to 64. 2. Allow the specified neighbor/peer group to send/ receive multiple path advertisements.
PAGE 186
deny deny deny deny deny deny deny Dell# 14551:112 701:667 702:667 703:667 704:666 705:666 14551:666 Configuring an IP Extended Community List To configure an IP extended community list, use these commands. 1. Create a extended community list and enter the EXTCOMMUNITY-LIST mode. CONFIGURATION mode ip extcommunity-list extcommunity-list-name 2. Two types of extended communities are supported.
PAGE 187
CONFIG-ROUTE-MAP mode match {community community-list-name [exact] | extcommunity extcommunity-list-name [exact]} 3. Return to CONFIGURATION mode. CONFIG-ROUTE-MAP mode exit 4. Enter ROUTER BGP mode. CONFIGURATION mode router bgp as-number AS-number: 0 to 65535 (2-Byte) or 1 to 4294967295 (4-Byte) or 0.1 to 65535.65535 (Dotted format) 5. Apply the route map to the neighbor or peer group’s incoming or outgoing routes.
PAGE 188
router bgp as-number 5. Apply the route map to the neighbor or peer group’s incoming or outgoing routes. CONFIG-ROUTER-BGP mode neighbor {ip-address | peer-group-name} route-map map-name {in | out} To view the BGP configuration, use the show config command in CONFIGURATION ROUTER BGP mode. To view a route map configuration, use the show route-map command in EXEC Privilege mode.
PAGE 189
bgp default local-preference value • value: the range is from 0 to 4294967295. The default is 100. To view the BGP configuration, use the show config command in CONFIGURATION ROUTER BGP mode or the show runningconfig bgp command in EXEC Privilege mode. A more flexible method for manipulating the LOCAL_PREF attribute value is to use a route map. 1. Enter the ROUTE-MAP mode and assign a name to a route map. CONFIGURATION mode route-map map-name [permit | deny] [sequence-number] 2.
PAGE 190
neighbor {ip-address | peer-group-name} weight weight • • weight: the range is from 0 to 65535. The default is 0. Sets weight for the route. CONFIG-ROUTE-MAP mode set weight weight • weight: the range is from 0 to 65535. To view BGP configuration, use the show config command in CONFIGURATION ROUTER BGP mode or the show runningconfig bgp command in EXEC Privilege mode. Enabling Multipath By default, the system supports one path to a destination.
PAGE 191
For information about configuring prefix lists, refer to Access Control Lists (ACLs). 3. Return to CONFIGURATION mode. CONFIG-PREFIX LIST mode exit 4. Enter ROUTER BGP mode. CONFIGURATION mode router bgp as-number 5. Filter routes based on the criteria in the configured prefix list.
PAGE 192
Filtering BGP Routes Using AS-PATH Information To filter routes based on AS-PATH information, use these commands. 1. Create a AS-PATH ACL and assign it a name. CONFIGURATION mode ip as-path access-list as-path-name 2. Create a AS-PATH ACL filter with a deny or permit action. AS-PATH ACL mode {deny | permit} as-regular-expression 3. Return to CONFIGURATION mode. AS-PATH ACL exit 4. Enter ROUTER BGP mode. CONFIGURATION mode router bgp as-number 5.
PAGE 193
Aggregating Routes The system provides multiple ways to aggregate routes in the BGP routing table. At least one specific route of the aggregate must be in the routing table for the configured aggregate to become active. To aggregate routes, use the following command. AS_SET includes AS_PATH and community information from the routes included in the aggregated route. • Assign the IP address and mask of the prefix to be aggregated.
PAGE 194
The constant router reaction to the WITHDRAWN and UPDATE notices causes instability in the BGP process. To minimize this instability, you may configure penalties (a numeric value) for routes that flap. When the penalty value reaches a configured limit, the route is not advertised, even if the route is up. The system uses a penalty value is 1024. As time passes and the route does not flap, the penalty value decrements or is decayed. However, if the route flaps again, it is assigned another penalty.
PAGE 195
• recent). Furthermore, in non-deterministic mode, the software may not compare MED attributes though the paths are from the same AS. Change the best path selection method to non-deterministic. Change the best path selection method to non-deterministic. CONFIG-ROUTER-BGP mode bgp non-deterministic-med NOTE: When you change the best path selection method, path selection for existing paths remains unchanged until you reset it by entering the clear ip bgp command in EXEC Privilege mode.
PAGE 196
• • keepalive: the range is from 1 to 65535. Time interval, in seconds, between keepalive messages sent to the neighbor routers. The default is 60 seconds. • holdtime: the range is from 3 to 65536. Time interval, in seconds, between the last keepalive message and declaring the router dead. The default is 180 seconds. Configure timer values for all neighbors. CONFIG-ROUTER-BGP mode timers bgp keepalive holdtime • • keepalive: the range is from 1 to 65535.
PAGE 197
If you specify a BGP peer group by using the peer-group-name argument, all members of the peer group inherit the characteristic configured with this command. • Clear all information or only specific details. EXEC Privilege mode clear ip bgp {* | neighbor-address | AS Numbers | ipv4 | peer-group-name} [soft [in | out]] • • *: Clears all peers. • neighbor-address: Clears the neighbor with this IP address. • AS Numbers: Peers’ AS numbers to be cleared. • ipv4: Clears information for the IPv4 address family.
PAGE 198
CONFIGURATION Mode router bgp as-number 2. Shut down the BGP neighbors corresponding to IPv4 multicast groups using the following command: ROUTER-BGP Mode shutdown address-family-ipv4-multicast To enable or disable BGP neighbors corresponding to the IPv6 unicast groups: 1. Enter the router bgp mode using the following command: CONFIGURATION Mode router bgp as-number 2.
PAGE 199
Set a Clause with a Continue Clause If the route-map entry contains sets with the continue clause, the set actions operation is performed first followed by the continue clause jump to the specified route map entry. • • If a set actions operation occurs in the first route map entry and then the same set action occurs with a different value in a subsequent route map entry, the last set of actions overrides the previous set of actions with the same set command.
PAGE 200
BGP Regular Expression Optimization The system optimizes processing time when using regular expressions by caching and re-using regular expression evaluated results, at the expense of some memory in RP1 processor. BGP policies that contain regular expressions to match against as-paths and communities might take a lot of CPU processing time, thus affect BGP routing convergence.
PAGE 201
Example of the show ip bgp neighbor Command to View Last and Bad PDUs Dell(conf-router_bgp)#do show ip bgp neighbors 1.1.1.2 BGP neighbor is 1.1.1.2, remote AS 2, external link BGP version 4, remote router ID 2.4.0.
PAGE 202
To view the captured PDUs, use the show capture bgp-pdu neighbor command. Dell#show capture bgp-pdu neighbor 20.20.20.2 Incoming packet capture enabled for BGP neighbor 20.20.20.
PAGE 203
Figure 25. Sample Configurations Example of Enabling BGP (Router 1) R1# conf R1(conf)#int loop 0 R1(conf-if-lo-0)#ip address 192.168.128.1/24 R1(conf-if-lo-0)#no shutdown R1(conf-if-lo-0)#show config ! interface Loopback 0 ip address 192.168.128.1/24 no shutdown R1(conf-if-lo-0)#int tengig 1/21 R1(conf-if-te-1/21)#ip address 10.0.1.21/24 R1(conf-if-te-1/21)#no shutdown R1(conf-if-te-1/21)#show config ! interface TenGigabitEthernet 1/21 ip address 10.0.1.
PAGE 204
R1(conf-router_bgp)#neighbor 192.168.128.3 update-source loop 0 R1(conf-router_bgp)#show config ! router bgp 99 network 192.168.128.0/24 neighbor 192.168.128.2 remote-as 99 neighbor 192.168.128.2 update-source Loopback 0 neighbor 192.168.128.2 no shutdown neighbor 192.168.128.3 remote-as 100 neighbor 192.168.128.3 update-source Loopback 0 neighbor 192.168.128.3 no shutdown R1(conf-router_bgp)#end R1# R1#show ip bgp summary BGP router identifier 192.168.128.
PAGE 205
neighbor 192.168.128.1 neighbor 192.168.128.3 neighbor 192.168.128.3 neighbor 192.168.128.3 R2(conf-router_bgp)#end no shutdown remote-as 100 update-source Loopback 0 no shutdown R2#show ip bgp summary BGP router identifier 192.168.128.
PAGE 206
R3(conf)#end R3#show ip bgp summary BGP router identifier 192.168.128.3, local AS number 100 BGP table version is 1, main routing table version 1 1 network entrie(s) using 132 bytes of memory 3 paths using 204 bytes of memory BGP-RIB over all using 207 bytes of memory 2 BGP path attribute entrie(s) using 128 bytes of memory 2 BGP AS-PATH entrie(s) using 90 bytes of memory 2 neighbor(s) using 9216 bytes of memory Neighbor AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/Pfx 192.168.128.
PAGE 207
Minimum time before advertisements start is 0 seconds Capabilities received from neighbor for IPv4 Unicast : MULTIPROTO_EXT(1) ROUTE_REFRESH(2) CISCO_ROUTE_REFRESH(128) Capabilities advertised to neighbor for IPv4 Unicast : MULTIPROTO_EXT(1) ROUTE_REFRESH(2) CISCO_ROUTE_REFRESH(128) Update source set to Loopback 0 Peer active in peer-group outbound optimization For address family: IPv4 Unicast BGP table version 1, neighbor version 1 Prefixes accepted 1 (consume 4 bytes), withdrawn 0 by peer Prefixes adverti
PAGE 208
neighbor AAA peer-group neighbor AAA no shutdown neighbor BBB peer-group neighbor BBB no shutdown neighbor 192.168.128.1 remote-as 99 neighbor 192.168.128.1 peer-group CCC neighbor 192.168.128.1 update-source Loopback 0 neighbor 192.168.128.1 no shutdown neighbor 192.168.128.3 remote-as 100 neighbor 192.168.128.3 peer-group BBB neighbor 192.168.128.3 update-source Loopback 0 neighbor 192.168.128.3 no shutdown R2(conf-router_bgp)#end R2# R2#show ip bgp summary BGP router identifier 192.168.128.
PAGE 209
192.168.128.1 99 93 192.168.128.2 99 122 R3#show ip bgp neighbor 99 120 1 1 0 0 (0) (0) 00:00:15 00:00:11 1 1 BGP neighbor is 192.168.128.1, remote AS 99, external link Member of peer-group BBB for session parameters BGP version 4, remote router ID 192.168.128.
PAGE 210
Received 138 messages, 0 in queue 7 opens, 2 notifications, 7 updates 122 keepalives, 0 route refresh requests Sent 140 messages, 0 in queue 7 opens, 4 notifications, 7 updates 122 keepalives, 0 route refresh requests Minimum time between advertisement runs is 30 seconds Minimum time before advertisements start is 0 seconds Capabilities advertised to neighbor for IPv4 Unicast : MULTIPROTO_EXT(1) Capabilities received from neighbor for IPv4 Unicast : MULTIPROTO_EXT(1) ROUTE_REFRESH(2) CISCO_ROUTE_REFRESH(128
PAGE 211
9 Content Addressable Memory (CAM) CAM is a type of memory that stores information in the form of a lookup table. On the switch, CAM stores Layer 2 and Layer 3 forwarding information, access-lists (ACLs), flows, and routing policies. On a line card, there are one or two CAM (Dual-CAM) modules per port-pipe.
PAGE 212
L2Acl Ipv4Acl Ipv6Acl Ipv4Qos L2Qos L2PT IpMacAcl VmanQos EcfmAcl Openflow : : : : : : : : : : 5 4 0 2 1 0 0 0 0 0 -- linecard 2 -Current Settings(in block sizes) 1 block = 256 entries L2Acl : 5 Ipv4Acl : 4 Ipv6Acl : 0 Ipv4Qos : 2 L2Qos : 1 L2PT : 0 IpMacAcl : 0 VmanQos : 0 EcfmAcl : 0 Openflow : 0 The ipv6acl and vman-dual-qos allocations must be entered as a factor of 2 (2, 4, 6, 8, 10). All other profile allocations can use either even or odd numbered ranges.
PAGE 213
Example of Viewing CAM-ACL Settings Dell# show cam-acl -- Chassis Cam ACL -Current Settings(in block sizes) 1 block = 256 entries L2Acl : 6 Ipv4Acl : 4 Ipv6Acl : 0 Ipv4Qos : 2 L2Qos : 1 L2PT : 0 IpMacAcl : 0 VmanQos : 0 EcfmAcl : 0 Openflow : 0 -- linecard 0 -Current Settings(in block sizes) 1 block = 256 entries L2Acl : 6 Ipv4Acl : 4 Ipv6Acl : 0 Ipv4Qos : 2 L2Qos : 1 L2PT : 0 IpMacAcl : 0 VmanQos : 0 EcfmAcl : 0 Openflow : 0 -- linecard 1 -Current Settings(in block sizes) 1 block = 256 entries L2Acl : 6 Ip
PAGE 214
1 | | | | | | | | | | | | | | | | | 1 | | | | | --More-- 0 | | | | | | | | | | | | | | | | | 1 | | | | | IN-L2 ACL IN-L2 FIB IN-L3 ACL IN-L3 ECMP GRP IN-L3 FIB IN-L3-SysFlow IN-L3-TrcList IN-L3-McastFib IN-L3-Qos IN-L3-PBR IN-V6 ACL IN-V6 FIB IN-V6-SysFlow IN-V6-McastFib OUT-L2 ACL OUT-L3 ACL OUT-V6 ACL IN-L2 ACL IN-L2 FIB IN-L3 ACL IN-L3 FIB IN-L3-SysFlow | | | | | | | | | | | | | | | | | | | | | | 1008 32768 12288 1024 262141 2878 1024 9215 8192 1024 0 0 0 0 1024 1024 0 320 32768 12288 262141 2878 |
PAGE 215
Example of Syslog message on CAM usage Following table shows few possible scenarios during which the syslog message appear on re-configuring the CAM usage threshold value. Consider if the last CAM threshold was set to 90 percent and now you re-configure the CAM threshold to 80. And, if the current CAM usage is 85 percent, then the system displays the syslog message saying that the CAM usage is above the configured CAM threshold value. Table 10.
PAGE 216
Applications for CAM Profiling The following describes link aggregation group (LAG) hashing. LAG Hashing The Dell Networking OS includes a CAM profile and microcode that treats MPLS packets as non-IP packets. Normally, switching and LAG hashing is based on source and destination MAC addresses. Alternatively, you can base LAG hashing for MPLS packets on source and destination IP addresses. This type of hashing is allowed for MPLS packets with five labels or less.
PAGE 217
Dell(conf)#hardware forwarding-table mode scaled-l3-hosts Hardware forwarding-table mode is changed. Save the configuration and reload to take effect. Dell(conf)#end Dell#write mem ! 01:13:36: %STKUNIT0-M:CP %FILEMGR-5-FILESAVED: Copied running-config to startup-config in flash by default Dell(conf)# Dell(conf)#end Dell#01:13:44: %STKUNIT0-M:CP %SYS-5-CONFIG_I: Configured from console Dell# 2. Display the hardware forwarding table mode in the current boot and in the next boot.
PAGE 218
10 Control Plane Policing (CoPP) Control plane policing (CoPP) protects the switch’s routing, control, and line-card processors from undesired or malicious traffic and Denial of Service (DoS) attacks by filtering control-plane flows. CoPP uses a dedicated control-plane service policy that consists of ACLs and QoS policies, which provide filtering and rate-limiting capabilities for control-plane packets.
PAGE 219
Table 12. Default Rate Limit for CPU queues CPU Queue Protocols Mapped to Control Processor Rate Limit (in kbps) Queues 0 TTL0, IP options, L3 Broadcast MAC destination address 1000 1 L3 MTU Fail 200 2 ARP request, NS, RS 1800 3 ARP reply, NA, RA 1800 4 FTP, Telnet, SSH, Local terminated, NTP, VLT IPM PDU, VLT ARPM 2800 5 ICMPv6 300 6 ICMP 300 7 DHCP, LLDP, FEFD, 8021x 3200 Table 13.
PAGE 220
CoPP Example The illustrations in this section show the benefit of using CoPP compared to not using CoPP on a switch. The following illustration shows how CoPP rate limits protocol traffic destined to the control-plane CPU. Figure 26. Control Plane Policing NOTE: On the system, CoPP does not convert the input rate of control-plane traffic from kilobits per second (kbps) to packets per second (pps) as on other Dell Networking switches.
PAGE 221
Figure 27. CoPP Versus Non-CoPP Operation Configure Control Plane Policing You can create a CoPP service policy on a per-protocol and/or a per-queue basis that serves as the system-wide configuration for filtering and rate limiting control-plane traffic. Configuring CoPP for Protocols This section describes how to create a protocol-based CoPP service policy and apply it to control plane traffic.
PAGE 222
ip access-list extended name cpu-qos permit {bgp | dhcp | dhcp-relay | ftp | icmp | igmp | msdp | ntp | ospf | pim | rip | ssh | telnet | vrrp} 3. Create an IPv6 ACL for specified protocol traffic. CONFIGURATION mode ipv6 access-list name cpu-qos permit {bgp | icmp | icmp-nd-na | icmp-nd-ns | icmp-rd-ra | icmp-rd-rs | ospf | vrrp} 4. Create a QoS input policy to rate limit input traffic.
PAGE 223
Example of Creating a QoS Rate-Limiting Input Policy Dell(conf)#qos-policy-in rate_limit_200k cpu-qos Dell(conf-in-qos-policy-cpuqos)#rate-police 200 40 peak 500 40 Dell(conf-in-qos-policy-cpuqos)#exit Dell(conf)#qos-policy-in rate_limit_400k cpu-qos Dell(conf-in-qos-policy-cpuqos)#rate-police 400 50 peak 600 50 Dell(conf-in-qos-policy-cpuqos)#exit Dell(conf)#qos-policy-in rate_limit_500k cpu-qos Dell(conf-in-qos-policy-cpuqos)#rate-police 500 50 peak 1000 50 Dell(conf-in-qos-policy-cpuqos)#exit Example of
PAGE 224
• • • Queues 0 to 6 process packets destined to the Control Processor CPU. Queues 7 to 13 process packets destined to the Route Processor CPU. Queues 14 to 20 process packets destined to the line-card CPU. For information about the default rate limits applied to the seven CPU queues for the Route Processor, Control Processor, and line cards, refer to CoPP Implementation. 3. Enter Control Plane configuration mode. CONFIGURATION mode control-plane-cpuqos 4.
PAGE 225
Q11 Q12 Q13 Q14 Q15 Q16 Q17 Q18 Q19 Q20 2600 2300 1800 1 1 1200 1200 7000 800 5000 Dell#show cpu-queue rate queue-id 8 Service-Queue Rate (kbps) -----------------------Q8 600 Dell#show cpu-queue rate range 8 12 Service-Queue Rate (kbps) -----------------------Q8 600 Q9 600 Q10 3200 Q11 2600 Q12 2300 6000 3000 3000 4000 100 100 1000 1000 7000 1000 Burst (kb) ---------1000 Burst (kb) ---------1000 1000 1000 6000 Viewing MAC Protocol-Queue Mapping To view the queues to which MAC protocol traffic is assig
PAGE 226
VRRP any any _ Q13 RP 400 Viewing IPv6 Protocol-Queue Mapping To view the queues to which IPv6 protocol traffic is assigned, use the show ipv6 protocol-queue-mapping command.
PAGE 227
v6 ICMP Q4 BGP Q13 OSPF Q13 RIP Q13 VRRP Q13 ICMP Q5 IGMP Q12 PIM Q12 MSDP Q12 BFD Q11/Q17 802.
PAGE 228
Viewing CPU Traffic Statistics To view the statistics collected on CPU traffic, use the show cpu-traffic-stats [cp | rp |all] command. Traffic statistics are sorted on a per-interface basis; the interface receiving the most traffic is displayed first. All CPU and port information is displayed unless you specify a port or CPU queue. Traffic information is displayed for router ports only, not for management interfaces.
PAGE 229
action={act=CopyToCpu, param0=1(0x1), param1=2(0x2), param2=0(0), param3=0(0)} policer= statistics={stat id 2 slice = 9 idx=0 entries=1}{Packets} --More-############## FP Entry for redirecting LACP traffic to CPU Port ############ EID 0x000002fd: gid=0xa, slice=9, slice_idx=0x3, part =0 prio=0x2fd, flags=0x10202, Installed, Enabled tcam: color_indep=0, Stage InPorts DATA=0x0000000000000000000000000000000000000000000000000000222222222222 MASK=0x000000000000000000000000000000000000000000000000000022222222222
PAGE 230
BFD BGP v6 BGP OSPF v6 OSPF/RIP VRRP v6 VRRP IGMP PIM NTP MULTICAST CATCH ALL/v6 MULTICAST CATCH ALL v6 ICMP RS DHCP RELAY/DHCP/IPv6 DHCP v6 ICMP NA v6 RA Guard/v6 ICMP RA v6 ICMP/ICMP MLD MSDP FTP/TELNET/SSH/L3 LOCAL TERMINATED L3 UNKNOWN/UNRESOLVED ARP iSCSI FCoE SFLOW HYPERPULL OPENFLOW L2 DST HIT/BROADCAST VLT TTL1/TRACEFLOW/TTL0/STATION MOVE/TTL1 /IP OPTION/L3 MTU FAIL/SOURCE MISS v6 ICMP NS 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
PAGE 231
STP LLDP PVST LACP ARP REQ ARP RESP GVRP FRRP ECFM ISIS L2PT v6 BGP v6 OSPF v6 VRRP MLD v6 MULTICAST CATCH ALL IPv6 DHCP v6 RAGUARD v6 ICMP NA v6 ICMP RA v6 ICMP NS v6 ICMP RS v6 ICMP BGP OSPF RIP VRRP ICMP IGMP PIM MSDP BFD ON PHYSICAL PORTS BFD ON LOGICAL PORTS 802.
PAGE 232
SFLOW_EGRESS SFLOW_INGRESS 0 0 0 0 0 0 To clear the per-protocol counters of rate-limited control-plane traffic at the aggregated (switch) or line card and port set level, use the clear control-traffic protocol [cp—switch | linecard {0–2} portset {0–3}] counters command; for example: Dell#clear control-traffic protocol linecard 1 portset 2 counters Dell# Dell#clear control-traffic protocol cp-switch counters Dell# Viewing Per-Queue CoPP Counters To view per-queue counters of CoPP rate-limited traffic,
PAGE 233
Dell#show control-traffic queue queue-id 6 counters Queue-ID RxBytes TxBytes Drops ------------------------Q6 0 0 Dell#clear control-traffic queue all counters 0 Control Plane Policing (CoPP) 233
PAGE 234
11 Data Center Bridging (DCB) Topics: • • • • • • • • • • • • • • • • Enabling Data Center Bridging Ethernet Enhancements in Data Center Bridging QoS dot1p Traffic Classification and Queue Assignment SNMP Support for PFC and Buffer Statistics Tracking DCB Maps and its Attributes Data Center Bridging: Default Configuration Configuration Notes: PFC and ETS in a DCB Map Configuring Priority-Based Flow Control Configuring Enhanced Transmission Selection Configure a DCBx Operation Verifying the DCB Configuratio
PAGE 235
Ethernet Enhancements in Data Center Bridging The following section describes DCB. The device supports the following DCB features: • • • Data center bridging exchange protocol (DCBx) Priority-based flow control (PFC) Enhanced transmission selection (ETS) NOTE: DCB is not supported on the Port Extender ports and Cascade ports.
PAGE 236
The following illustration shows how PFC handles traffic congestion by pausing the transmission of incoming traffic with dot1p priority 4. Figure 28. Illustration of Traffic Congestion The system supports loading two DCB_Config files: • • FCoE converged traffic with priority 3. iSCSI storage traffic with priority 4. In the Dell Networking OS, PFC is implemented as follows: • • • • • PFC is supported on specified 802.1p priority traffic (dot1p 0 to 7) and is configured per interface.
PAGE 237
Figure 29. Enhanced Transmission Selection The following table lists the traffic groupings ETS uses to select multiprotocol traffic for transmission. Table 15. ETS Traffic Groupings Traffic Groupings Description Group ID A 4-bit identifier assigned to each priority group. The range is from 0 to 7 configurable; 8 - 14 reservation and 15.0 - 15.7 is strict priority group.. Group bandwidth Percentage of available bandwidth allocated to a priority group.
PAGE 238
Data Center Bridging in a Traffic Flow The following figure shows how DCB handles a traffic flow on an interface. Figure 30. DCB PFC and ETS Traffic Handling QoS dot1p Traffic Classification and Queue Assignment The following section describes QoS dot1P traffic classification and assignments.
PAGE 239
dot1p Value in the Incoming Frame Egress Queue Assignment 2 2 3 3 4 4 5 5 6 6 7 7 Dell#show qos dot1p-queue-mapping Dot1p Priority : 0 1 2 3 4 5 6 7 Queue : 1 0 2 3 4 5 6 7 SNMP Support for PFC and Buffer Statistics Tracking Buffer Statistics Tracking (BST) feature provides a mechanism to aid in Resource Monitoring and Tuning of Buffer Allocation. Max Use Count mode in Buffer Statistics is supported.
PAGE 240
DCB Maps and its Attributes This topic contains the following sections that describe how to configure a DCB map, apply the configured DCB map to a port, configure PFC without a DCB map, and configure lossless queues. DCB Map: Configuration Procedure A DCB map consists of PFC and ETS parameters. By default, PFC is not enabled on any 802.1p priority and ETS allocates equal bandwidth to each priority. To configure user-defined PFC and ETS settings, you must create a DCB map.
PAGE 241
Table 16. Applying a DCB map to an Ethernet port Step Task Command Command Mode 1 Enter interface configuration mode on an Ethernet port.
PAGE 242
Configuring Lossless Queues DCB also supports the manual configuration of lossless queues on an interface after you disable PFC mode in a DCB map and apply the map on the interface. The configuration of no-drop queues provides flexibility for ports on which PFC is not needed, but lossless traffic should egress from the interface. Lossless traffic egresses out the no-drop queues. Ingress 802.1p traffic from PFC-enabled peers is automatically mapped to the no-drop egress queues.
PAGE 243
Applying a DCB Map on a Line Card On the C9010, DCB is supported per-line card. If the traffic handled by a DCB map is transmitted on ports on different line cards, you must manually configure the DCB map on the backplane ports of the C9010 line cards on which the ports reside. • Apply a DCB map with PFC and ETS settings on the backplane ports of C9010 line cards.
PAGE 244
As soon as you apply a DCB map with PFC enabled on an interface, DCBx starts exchanging information with a peer. The IEEE802.1Qbb, CEE and CIN versions of PFC TLV are supported. DCBx also validates PFC configurations that are received in TLVs from peer devices. By applying a DCB map with PFC enabled, you enable PFC operations on ingress port traffic. To achieve complete lossless handling of traffic, configure PFC priorities on all DCB egress ports.
PAGE 245
• ETS configuration error: If an error occurs in an ETS configuration, the configuration is ignored and the scheduler and bandwidth allocation settings are reset to the ETS default value: 100% of available bandwidth is allocated to priority group 0 and the bandwidth is equally assigned to each dot1p priority. If an error occurs when a port receives a peer’s ETS configuration, the port’s configuration resets to the ETS configuration in the previously configured DCB map.
PAGE 246
Committed and peak burst size is in kilobytes. Default is 50. The range is from 0 to 10000. The pfc on command enables priority-based flow control. 3. Specify the dot1p priority-to-priority group mapping for each priority. priority-pgid dot1p0_group_num dot1p1_group_num ...dot1p7_group_num Priority group range is from 0 to 7. All priorities that map to the same queue must be in the same priority group. Leave a space between each priority group number.
PAGE 247
For example, storage traffic is sensitive to frame loss; interprocess communication (IPC) traffic is latency-sensitive. ETS allows different traffic types to coexist without interruption in the same converged link by: • • Allocating a guaranteed share of bandwidth to each priority group. Allowing each group to exceed its minimum guaranteed bandwidth if another group is not fully using its allotted bandwidth. Creating an ETS Priority Group An ETS priority group specifies the range of 802.
PAGE 248
• • In the CEE version, the priority group/traffic class group (TCG) ID 15 represents a non-ETS priority group. Any priority group configured with a scheduler type is treated as a strict-priority group and is given the priority-group (TCG) ID 15. The CIN version supports two types of strict-priority scheduling: • • Group strict priority: Use this to increase its bandwidth usage to the bandwidth total of the priority group and allow a single priority flow in a priority group.
PAGE 249
• • Auto-downstream The configuration received from a DCBx peer or from an internally propagated configuration is not stored in the switch’s running configuration. On a DCBx port in an auto-upstream role, the PFC and application priority TLVs are enabled. ETS recommend TLVs are disabled and ETS configuration TLVs are enabled. The port advertises its own configuration to DCBx peers but is not willing to receive remote peer configuration.
PAGE 250
DCB Configuration Exchange The DCBx protocol supports the exchange and propagation of configuration information for the enhanced transmission selection (ETS) and priority-based flow control (PFC) DCB features. DCBx uses the following methods to exchange DCB configuration parameters: Asymmetric DCB parameters are exchanged between a DCBx-enabled port and a peer port without requiring that a peer port and the local port use the same configured values for the configurations to be compatible.
PAGE 251
Auto-Detection and Manual Configuration of the DCBx Version When operating in Auto-Detection mode (the DCBx version auto command), a DCBx port automatically detects the DCBx version on a peer port. Legacy CIN and CEE versions are supported in addition to the standard IEEE version 2.5 DCBx. A DCBx port detects a peer version after receiving a valid frame for that version.
PAGE 252
class-map match-any dscp-pfc-2 match ip dscp 20-25,30-35 2. Associate above class-maps to Queues Queue assignment as below. Table 19. Queue Assignments Internal-priority Queue 0 0 1 0 2 0 3 1 4 2 5 3 6 3 7 3 3. Dot1p->Queue Mapping Configuration is retained at the default value. 4. Interface Configurations on server connected ports. a. Enable DCB globally. DellEMC(conf)#dcb enable b. Apply PFC Priority configuration. Configure priorities on which PFC is enabled.
PAGE 253
Figure 31. DCBx Sample Topology DCBx Prerequisites and Restrictions The following prerequisites and restrictions apply when you configure DCBx operation on a port: • • For DCBx, on a port interface, enable LLDP in both Send (TX) and Receive (RX) mode (the protocol lldp mode command; refer to the example in CONFIGURATION versus INTERFACE Configurations in the Link Layer Discovery Protocol (LLDP) chapter). If multiple DCBx peer ports are detected on a local DCBx interface, LLDP is shut down.
PAGE 254
2. Configure server-facing interfaces as auto-downstream ports. 3. Configure a port to operate in a configuration-source role. 4. Configure ports to operate in a manual role. NOTE: The DCBx configuration is not supported on cascade interfaces or extended ports 1. Enter INTERFACE Configuration mode. CONFIGURATION mode interface type slot/port 2. Enter LLDP Configuration mode to enable DCBx operation. INTERFACE mode [no] protocol lldp 3.
PAGE 255
To verify the DCBx configuration on a port, use the show interface DCBx detail command. Configuring DCBx Globally on the Switch To globally configure the DCBx operation on a switch, follow these steps. 1. Enter Global Configuration mode. EXEC PRIVILEGE mode configure 2. Enter LLDP Configuration mode to enable DCBx operation. CONFIGURATION mode [no] protocol lldp 3. Configure the DCBx version used on all interfaces not already configured to exchange DCB information.
PAGE 256
DCBx Error Messages The following syslog messages appear when an error in DCBx operation occurs. LLDP_MULTIPLE_PEER_DETECTED: DCBx is operationally disabled after detecting more than one DCBx peer on the port interface. LLDP_PEER_AGE_OUT: DCBx is disabled as a result of LLDP timing out on a DCBx peer interface. DSM_DCBx_PEER_VERSION_CONFLICT: A local port expected to receive the IEEE, CIN, or CEE version in a DCBx TLV from a remote peer but received a different, conflicting DCBx version.
PAGE 257
Command Output You can use the show interface pfc statistics command even without enabling DCB on the system. show interface port-type slot/port ets {summary Displays the ETS configuration applied to egress traffic on an | detail} interface, including priority groups with priorities and bandwidth allocation. To clear ETS TLV counters, enter the clear ets counters interface port-type slot/port command. show interface port-type slot/port DCBx detail Plays the DCBx configuration on an interface.
PAGE 258
Local FCOE PriorityMap is 0x8 Local ISCSI PriorityMap is 0x10 Remote FCOE PriorityMap is 0x8 Remote ISCSI PriorityMap is 0x8 Dell# show interfaces tengigabitethernet 1/4 pfc detail Interface TenGigabitEthernet 1/4 Admin mode is on Admin is enabled Remote is enabled Remote Willing Status is enabled Local is enabled Oper status is recommended PFC DCBx Oper status is Up State Machine Type is Feature TLV Tx Status is enabled PFC Link Delay 45556 pause quanta Application Priority TLV Parameters : ---------------
PAGE 259
Fields Description PFC Link Delay Link delay (in quanta) used to pause specified priority traffic. Application Priority TLV: FCOE TLV Tx Status Status of FCoE advertisements in application priority TLVs from local DCBx port: enabled or disabled. Application Priority TLV: ISCSI TLV Tx Status Status of ISCSI advertisements in application priority TLVs from local DCBx port: enabled or disabled.
PAGE 260
------------------Remote is disabled Local Parameters : -----------------Local is enabled TC-grp Priority# Bandwidth TSA -----------------------------------------------0 1 0,1,2 100% ETS 2 3 0 % SP 3 4,5,6,7 0 % SP 4 5 6 7 Oper status is init ETS DCBx Oper status is Down State Machine Type is Asymmetric Conf TLV Tx Status is enabled Reco TLV Tx Status is enabled 0 Input Conf TLV Pkts, 1955 Output Conf TLV Pkts, 0 Error Conf TLV Pkts 0 Input Reco TLV Pkts, 1955 Output Reco TLV Pkts, 0 Error Reco TLV Pkts Del
PAGE 261
5 12% ETS 6 12% ETS 7 12% ETS Oper status is init Conf TLV Tx Status is disabled Traffic Class TLV Tx Status is disabled 0 Input Conf TLV Pkts, 0 Output Conf TLV Pkts, 0 Error Conf TLV Pkts 0T LIVnput Traffic Class TLV Pkts, 0 Output Traffic Class TLV Pkts, 0 Error Traffic Class Pkts The following example shows the show interface ets detail command.
PAGE 262
0 Input Traffic Class TLV Pkts, 0 Output Traffic Class TLV Pkts, 0 Error Traffic Class TLV Pkts Dell#show interfaces fortyGige 0/36 ets detail Interface fortyGigE 0/36 Max Supported PG is 3 Number of Traffic Classes is 8 Admin mode is on Admin Parameters : -----------------Admin is enabled PG-grp Priority# BW-% BW-COMMITTED BW-PEAK TSA % Rate(Mbps) Burst(KB) Rate(Mpbs) Burst(KB) ----------------------------------------------------0 0,1,2,4,5,6,7 50 400 100 4000 400 ETS 1 3 50 - - - - ETS 2 - - - - - 3 - - -
PAGE 263
Field Description Admin mode is enabled on the remote port for DCBx exchange, the Willing bit received in ETS TLVs from the remote peer is included. Local Parameters ETS configuration on local port, including Admin mode (enabled when a valid TLV is received from a peer), priority groups, assigned dot1p priorities, and bandwidth allocation. Operational status (local port) Port state for current operational ETS configuration: • • • Init: Local ETS configuration parameters were exchanged with peer.
PAGE 264
6 7 - - Dell# show interface tengigabit 2/12 dcbx details E-ETS Configuration TLV enabled e-ETS Configuration TLV disabled R-ETS Recommendation TLV enabled r-ETS Recommendation TLV disabled P-PFC Configuration TLV enabled p-PFC Configuration TLV disabled F-Application priority for FCOE enabled f-Application Priority for FCOE disabled I-Application priority for iSCSI enabled i-Application Priority for iSCSI disabled -----------------------------------------------------------------------------------Interfa
PAGE 265
Table 23. show interface DCBx detail Command Description Field Description Interface Interface type with chassis slot and port number. Port-Role Configured DCBx port role: auto-upstream, auto-downstream, config-source, or manual. DCBx Operational Status Operational status (enabled or disabled) used to elect a configuration source and internally propagate a DCB configuration. The DCBx operational status is the combination of PFC and ETS operational status.
PAGE 266
For the tagged packets, Queue is selected based on the incoming Packet Dot1p. When PFC frames for a specific priority is received from the peer switch, the queue corresponding to that Dot1p is halted from scheduling on that port, thus honoring the PFC from the peer. If a queue is congested due to packets with a specific Dot1p and PFC is enabled for that Dot1p, switch will transit out PFC frames for that Dot1p.
PAGE 267
Figure 32. PFC and ETS Applied to LAN, IPC, and SAN Priority Traffic QoS Traffic Classification: The service-class dynamic dot1p command has been used in Global Configuration mode to map ingress dot1p frames to the queues shown in the following table. For more information, refer to QoS dot1p Traffic Classification and Queue Assignment.
PAGE 268
The following describes the priority group-bandwidth assignment. PFC and ETS Configuration Command Examples The following examples show PFC and ETS configuration commands to manage your data center traffic.
PAGE 269
• Strict-priority groups: If priority group 1 or 2 has free bandwidth, (20 + 30)% of the free bandwidth is distributed to priority group 3. Priority groups 1 and 2 retain whatever free bandwidth remains up to the (20+ 30)%. If two priority groups have strict-priority scheduling, traffic assigned from the priority group with the higher priority-queue number is scheduled first.
PAGE 270
Configuring the Dynamic Buffer Method Priority-based flow control using dynamic buffer spaces is supported on the switch. To configure the dynamic buffer capability, perform the following steps: 1. Enable the DCB application. By default, DCB is enabled and link-level flow control is disabled on all interfaces. CONFIGURATION mode dcb enable 2. Configure the shared PFC buffer size and the total buffer size. A maximum of 4 lossless queues are supported.
PAGE 271
12 Debugging and Diagnostics This chapter describes the debugging and diagnostics tasks you can perform on the switch.
PAGE 272
Warning - PE-Unit 0 at PEID 0 will go offline to run the diagnostics. Offline of system will bring down all the protocols and the system will be operationally down, except for running Diagnostics. PE unit will be automatically reloaded once the diagnostics tests are completed.
PAGE 273
Jul 30 13:11:07: %PE255-C1048P:2 %CHMGR-2-FAN_SPEED_CHANGE: Fan speed changed to 60 % of the full speed Jul 30 13:11:07: %PE255-UNIT3-M:CP %IFMGR-5-OSTATE_UP: Changed interface state to up: Te 2/1 Jul 30 13:11:54: %PE255-C1048P:2 %CHMGR-2-FAN_SPEED_CHANGE: Fan speed changed to 75 % of the full speed Jul 30 13:11:54: %PE255-UNIT3-M:CP %CHMGR-4-TEMP_STATUS_CHANGE: Unit 2 temperature state changed to 1 (Current temperature 35C).
PAGE 274
006 - One Gig PHY Access Test ...................................... PASS 007 - One Gig PHY Access Test ...................................... PASS 008 - One Gig PHY Access Test ...................................... PASS 009 - One Gig PHY Access Test ...................................... PASS 010 - One Gig PHY Access Test ...................................... PASS 011 - One Gig PHY Access Test ...................................... PASS 012 - One Gig PHY Access Test ......................................
PAGE 275
043 - One Gig PHY Access Test ...................................... PASS 044 - One Gig PHY Access Test ...................................... PASS 045 - One Gig PHY Access Test ...................................... PASS 046 - One Gig PHY Access Test ...................................... PASS 047 - One Gig PHY Access Test ...................................... PASS 048 - One Gig PHY Access Test ...................................... PASS oneGAccess ..................................................
PAGE 276
002 - One Gig PHY Link Test ........................................ PASS 003 - One Gig PHY Link Test ........................................ PASS 004 - One Gig PHY Link Test ........................................ PASS 005 - One Gig PHY Link Test ........................................ PASS 006 - One Gig PHY Link Test ........................................ PASS 007 - One Gig PHY Link Test ........................................ PASS 008 - One Gig PHY Link Test ........................................
PAGE 277
usbRW (1, 1) The following example shows how to run offline diagnostics for PE in Debug mode. NOTE: Dell Networking highly recommends reloading the system after running the offline diagnostics in Debug mode on the switch.
PAGE 278
A warning is displayed with a CLI prompt asking you to click Yes or No Dell#diag system Warning - diagnostic execution will cause multiple link flaps on the peer side advisable to shut directly connected ports Proceed with Diags [confirm yes/no]: 5. View the results of the diagnostic tests. EXEC Privilege Mode show file flash://TestReport-CP-unit.txt show file flash://TestReport-LP-linecard-number.txt The following example takes a switch offline.
PAGE 279
0 0 0 0 0 1 2 3 Total power: absent absent absent up AC up 3440 599.0 599.
PAGE 280
19 20 21 22 23 24 25 26 27 28 29 30 31 -rwx -rwx -rwx -rwx -rwx -rwx -rwx -rwx -rwx drwx -rwx -rwx -rwx 3160 484734 569421 265208 569421 262890 569677 251098 11518 4096 52186974 10918 17134 Apr Feb Feb Feb Feb Feb Feb Feb Apr Mar Apr Apr Apr 24 19 19 19 19 19 19 19 26 13 24 26 26 2015 2015 2015 2015 2015 2015 2015 2015 2015 2015 2015 2015 2015 19:27:06 12:10:04 12:13:28 12:16:18 12:18:24 12:21:42 12:23:14 12:24:14 22:33:08 02:28:26 19:28:16 22:33:08 22:35:56 +00:00 +00:00 +00:00 +00:00 +00:00 +00:00
PAGE 281
ERROR: optic:17 is not present ERROR: optic:21 is not present opticEepromTest ............................................. FAIL opticPhyTest ................................................ PASS Starting test: opticPresenceTest ...... ERROR: optic:1 is not present ERROR: optic:5 is not present ERROR: optic:9 is not present ERROR: optic:13 is not present ERROR: optic:17 is not present ERROR: optic:21 is not present opticPresenceTest ...........................................
PAGE 282
/dev/rwd0k: 3 files, 20398 free (10199 clusters) Iteration 8 - File System Check passed /dev/rwd0k: 3 files, 20398 free (10199 clusters) Iteration 9 - File System Check passed /dev/rwd0k: 3 files, 20398 free (10199 clusters) Iteration 10 - File System Check passed /dev/rwd0k: 3 files, 20398 free (10199 clusters) Iteration 11 - File System Check passed /dev/rwd0k: 3 files, 20398 free (10199 clusters) Iteration 12 - File System Check passed /dev/rwd0k: 3 files, 20398 free (10199 clusters) Iteration 13 - File
PAGE 283
Iteration 44 - File System Check passed /dev/rwd0k: 3 files, 20398 free (10199 clusters) Iteration 45 - File System Check passed /dev/rwd0k: 3 files, 20398 free (10199 clusters) Iteration 46 - File System Check passed /dev/rwd0k: 3 files, 20398 free (10199 clusters) Iteration 47 - File System Check passed /dev/rwd0k: 3 files, 20398 free (10199 clusters) Iteration 48 - File System Check passed /dev/rwd0k: 3 files, 20398 free (10199 clusters) Iteration 49 - File System Check passed /dev/rwd0k: 3 files, 20398
PAGE 284
cpuGELinkStatusTest ......................................... FAIL cpuRevisionTest ............................................. PASS cpuSdramPresenceTest ........................................ PASS cpuSdramSizeTest ............................................ PASS eepromTest .................................................. PASS Starting test: extendedCPLDAccessTest ......extended CPLD Major Ver 2 Minor Ver 3 extendedCPLDAccessTest ...................................... PASS fanAirFlowDirection ........
PAGE 285
PSU[2] Status Test FAIL psuStatusTest ............................................... FAIL Starting test: psuVoltageTest ...... PSU[0] Voltage Test FAIL PSU[1] Voltage Test FAIL PSU[2] Voltage Test FAIL psuVoltageTest .............................................. FAIL rtcTest ..................................................... PASS sataSsdTest ................................................. PASS Starting test: showTemperature ...... +Board First Thermal Monitor Sensor[0] is 38.
PAGE 286
ERROR: Fan speed variation failed for tray[2] FAN TRAY[2] FAN 2 Controller Speed Test FAIL ERROR: Tray[2] fan[3] speed 56% is out of expected range [80-100%] ERROR: Fan speed variation failed for tray[2] FAN TRAY[2] FAN 3 Controller Speed Test FAIL fanCntrlSpeedTest ........................................... FAIL fanTrayEepromAccessTest ..................................... PASS Starting test: i2cTest ......
PAGE 287
/dev/rwd0k: 3 files, 20398 free (10199 clusters) Iteration 23 - File System Check passed /dev/rwd0k: 3 files, 20398 free (10199 clusters) Iteration 24 - File System Check passed /dev/rwd0k: 3 files, 20398 free (10199 clusters) Iteration 25 - File System Check passed /dev/rwd0k: 3 files, 20398 free (10199 clusters) Iteration 26 - File System Check passed /dev/rwd0k: 3 files, 20398 free (10199 clusters) Iteration 27 - File System Check passed /dev/rwd0k: 3 files, 20398 free (10199 clusters) Iteration 28 - Fil
PAGE 288
usbTest ..................................................... FAIL LEVEL 2 DIAGNOSTIC ipcPingTrafficTest ..........................................
PAGE 289
LEVEL 0 DIAGNOSTIC Starting test: bcm56854AccessTest ...... + Access Test for unit 0 : PASSED bcm56854AccessTest .......................................... PASS biosVerGetTest .............................................. PASS boardRevisionTest ........................................... PASS cpldAccessTest .............................................. PASS Starting test: CpuGbeLinkStatusTest ...... + GbE1 Link Status UP + GbE2 Link Status DOWN CpuGbeLinkStatusTest ........................................
PAGE 290
Starting test: udfLinkStatus ...... ERROR: Unit 0 xe port 26 is DOWN udfLinkStatus ............................................... FAIL xeLinkSpeedTest ............................................. PASS Starting test: xeLinkStatusTest ...... ERROR: Unit 0 xe port 1 is DOWN ERROR: Unit 0 xe port 5 is DOWN ERROR: Unit 0 xe port 9 is DOWN ERROR: Unit 0 xe port 13 is DOWN ERROR: Unit 0 xe port 17 is DOWN ERROR: Unit 0 xe port 21 is DOWN xeLinkStatusTest ............................................
PAGE 291
/dev/rwd0k: 3 files, 20398 free (10199 clusters) Iteration 27 - File System Check passed /dev/rwd0k: 3 files, 20398 free (10199 clusters) Iteration 28 - File System Check passed /dev/rwd0k: 3 files, 20398 free (10199 clusters) Iteration 29 - File System Check passed /dev/rwd0k: 3 files, 20398 free (10199 clusters) Iteration 30 - File System Check passed /dev/rwd0k: 3 files, 20398 free (10199 clusters) Iteration 31 - File System Check passed /dev/rwd0k: 3 files, 20398 free (10199 clusters) Iteration 32 - Fil
PAGE 292
udfLinkStatus (0, 1) xeLinkStatusTest (0, 1) ipcTrafficTest (2, 1) ------------------------------------------------------------------The following example shows the show diag in control processor command. Dell#show diag cp unit detail Diag status of CP unit: -------------------------------------------------------------------------Board: C9010 Dell Networking ================================================= CP unit is currently offline. CP unit alllevels diag issued at Sun Apr 26, 2015 10:32:01 PM.
PAGE 293
ERROR: ioctl: "lm9" op(1)=READ WITH STOP bus=26 address=0x4b offset=0 length=1 i2cTest ..................................................... FAIL interruptStatusTest ......................................... PASS Starting test: lmPresenceTest ......LM Slot0 Not Present LM Slot1 Present LM Slot2 Not Present LM Slot3 Not Present LM Slot4 Present LM Slot5 Present LM Slot6 Not Present LM Slot7 Not Present LM Slot8 Not Present LM Slot9 Not Present Peer RPM Not Present lmPresenceTest .............................
PAGE 294
Sensor Temperature : 27 c Sensor Temperature : 31 c DDR Temperature 33 c showTemperature ............................................. PASS Starting test: slotInfoTest ......RPM Slot No 0 slotInfoTest ................................................ PASS spiFlashAccessTest .......................................... PASS Starting test: udfAccessTest ...... + Access Test for unit 0 : PASSED udfAccessTest ............................................... PASS Starting test: usbTest ......
PAGE 295
interruptStatusRegister ..................................... Starting test: psuEepromAccessTest ...... PSU [0] Eeprom Access Test FAIL PSU [1] Eeprom Access Test FAIL PSU [2] Eeprom Access Test FAIL psuEepromAccessTest ......................................... rtcTest ..................................................... sataSsdTest ................................................. Starting test: ssdFlashFileSystemStressTest ......
PAGE 296
/dev/rwd0k: 3 files, 20398 free (10199 clusters) Iteration 33 - File System Check passed /dev/rwd0k: 3 files, 20398 free (10199 clusters) Iteration 34 - File System Check passed /dev/rwd0k: 3 files, 20398 free (10199 clusters) Iteration 35 - File System Check passed /dev/rwd0k: 3 files, 20398 free (10199 clusters) Iteration 36 - File System Check passed /dev/rwd0k: 3 files, 20398 free (10199 clusters) Iteration 37 - File System Check passed /dev/rwd0k: 3 files, 20398 free (10199 clusters) Iteration 38 - Fil
PAGE 297
psuFanAirFlowDirectionTest psuFanSpeedTest psuFanStatusTest psuPresenceTest psuShowTempTest psuStatusTest psuVoltageTest usbTest fanCntrlSpeedTest i2cTest psuEepromAccessTest udfLinkStatusTest usbTest ipcPingTrafficTest (0, (0, (0, (0, (0, (0, (0, (0, (1, (1, (1, (1, (1, (2, 1) 1) 1) 1) 1) 1) 1) 1) 1) 1) 1) 1) 1) 1) TRACE Logs In addition to the syslog buffer, to report hardware and software events and status information, the system buffers trace messages which are continuously written by various softwar
PAGE 298
Causes Displayed Reasons Reload normal power-cycle Table 25. Linecard Restart Causes and Reasons Causes Displayed Reasons Reset of linecard powered-on show hardware Commands Use the show hardware commands to troubleshoot error conditions by displaying information about a hardware subcomponent and details from hardware-based feature tables. NOTE: Use the show hardware commands only under the guidance of the Dell Networking Technical Assistance Center (TAC).
PAGE 299
• • • • • • • • • • • • show hardware unit unit-number ipmc-replication Display the internal statistics for each port-pipe (unit) on per port basis. show hardware linecard slot—id unit unit-number port-stats [detail] Display the line-card internal registers for each port-pipe. show hardware linecard slot—id unit unit-number register Display the tables from the bShell through the CLI without going into the bShell.
PAGE 300
Example of the show interfaces transceiver Command Dell#show interfaces tengigabitethernet 10/1 transceiver SFP is present SFP+ 1 Serial Base ID fields SFP+ 1 Id = 0x03 SFP+ 1 Ext Id = 0x04 SFP+ 1 Connector = 0x21 SFP+ 1 Transceiver Code = 0x00 0x00 0x00 0x00 0x00 0x04 0x00 0x00 SFP+ 1 Encoding = 0x00 SFP+ 1 BR Nominal = 0x67 SFP+ 1 Length(SFM) Km = 0x00 SFP+ 1 Length(OM3) 2m = 0x00 SFP+ 1 Length(OM2) 1m = 0x00 SFP+ 1 Length(OM1) 1m = 0x00 SFP+ 1 Length(Copper) 1m = 0x01 SFP+ 1 Vendor Rev = A SFP+ 1 Laser W
PAGE 301
• Use the show alarms command to display power-supply alarm messages. Dell#show alarms ... -- Major Alarms -Alarm Type Duration --------------------------------------------------------------------------PEM 0 in unit 0 down 25 sec PEM 2 in unit 0 down 6 sec • Use the show environment pem command to display complete information on power supply operation.
PAGE 302
2 2 2 2 2 2 2 2 2 2 2 4 8 12 16 20 24 28 32 36 40 44 QSFP QSFP QSFP Media not present Media not present Media not present 40GBASE-SR4 Media not present 40GBASE-CR4-1M Media not present Media not present Media not present 40GBASE-SR4 Media not present or accessible or accessible or accessible 7503825D0169 or accessible APF12380010GM4 or accessible or accessible or accessible 7503825H006J or accessible Yes Yes Yes To display more detailed information about the transceiver type, wavelength, and power r
PAGE 303
QSFP 168 Temp Low Warning threshold QSFP 168 Voltage Low Warning threshold QSFP 168 Bias Low Warning threshold QSFP 168 RX Power Low Warning threshold =================================== QSFP 168 Temperature QSFP 168 Voltage QSFP 168 TX1 Bias Current QSFP 168 TX2 Bias Current QSFP 168 TX3 Bias Current QSFP 168 TX4 Bias Current QSFP 168 RX1 Power QSFP 168 RX2 Power QSFP 168 RX3 Power QSFP 168 RX4 Power = = = = -5.000C 3.135V 10.000mA 0.043mW = = = = = = = = = = 21.891C 3.314V 0.000mA 0.000mA 0.000mA 0.
PAGE 304
Examples of Syslog Temperature Alarm Conditions The following are example syslogs temperature alarm conditions in the system.
PAGE 305
RP Boot Selector : 3.3.0.
PAGE 306
• • • • • • • • • • • • • show hardware linecard {0-2} unit {0-3} {counters | details | port-stats [detail] | register | execute-shell-cmd | ipmc-replication | table-dump} show hardware {layer2| layer3} {e.g. acl |in acl} linecard {0-2} port—set {0-3} show hardware layer3 qos linecard {0-2} port—set {0-3} show hardware ipv6 {e.g.
PAGE 307
Internal 60 Internal 61 0 0 0 0 0 0 0 0 0 0 Displaying Dataplane Statistics The show hardware linecard {0–2} cpu data-plane statistics command provides information about the packet types entering a line-card CPU. As shown in the following example, the show hardware linecard cpu data-plane statistics command output provides detailed RX/TX packet statistics on a per-queue basis.
PAGE 308
tx_q3_pkts = 0 tx_q4_pkts = 0 tx_q5_pkts = 0 tx_broad_pkts = 114500 tx_multi_pkts = 7422 tx_uni_pkts = 475954 tx_pause_pkts = 0 tx_cols = 0 tx_single_cols = 0 tx_multi_cols = 0 tx_late_cols = 0 tx_excess_cols = 0 tx_deferred = 0 tx_discarded = 0 Party Bus Receive Counters for port 0: Rx Octets = 251640594 Rx Undersize Packets = 0 Rx Oversize Packets = 0 Rx Pause Packets = 0 Rx 64 Octet Packets = 122688 Rx 65to127octets Packets = 246245 Rx 128to255octets Packets = 441 Rx 256to511octets Packets = 3816 Rx 512t
PAGE 309
Accessing Application Core Dumps Core dumps for an application crash are enabled by default. On the system, core dumps are generated and stored in the local flash of the system’s Control Processor CPU. To access an application core-dump file, you must perform an FTP to the Control Processor CPU flash directory where the application core dump is stored in the following formats: • An application core dump generated from CP of the RPM: • f10Ch_rpm<0/1>_cp__.acore.
PAGE 310
• The Kernel mini core dump generated from the LM: f10Ch_lp_.kcore.mini.txt The panic string contains key information regarding the crash. Several panic string types exist, and they are displayed in regular english text to enable easier understanding of the crash cause.
PAGE 311
You can use the capture-duration timer and the packet-count counter at the same time. The TCP dump stops when the first of the thresholds are met. That means that even if the duration timer is 9000 seconds, if the maximum file count parameter is met first, the dumps stop. • Enable a TCP dump for CPU bound traffic.
PAGE 312
13 Dynamic Host Configuration Protocol (DHCP) DHCP is an application layer protocol that dynamically assigns IP addresses and other configuration parameters to network end-stations (hosts) based on configuration policies determined by network administrators.
PAGE 313
Option Number and Description Specifies the client’s subnet mask. Router Option 3 Specifies the router IP addresses that may serve as the client’s default gateway. Domain Name Server Option 6 Domain Name Option 15 Specifies the domain name servers (DNSs) that are available to the client. Specifies the domain name that clients should use when resolving hostnames via DNS.
PAGE 314
2. Servers unicast or broadcast a DHCPOFFER message in response to the DHCPDISCOVER that offers to the client values for the requested parameters. Multiple servers might respond to a single DHCPDISCOVER; the client might wait a period of time and then act on the most preferred offer. 3. The client broadcasts a DHCPREQUEST message in response to the offer, requesting the offered values. 4.
PAGE 315
• • The switch supports 4K DHCP Snooping entries. All platforms support Dynamic ARP Inspection on 16 VLANs per system. For more information, refer to Dynamic ARP Inspection. NOTE: If the DHCP server is on the top of rack (ToR) and the VLTi (ICL) is down due to a failed link, when a VLT node is rebooted in JumpStart mode, it is not able to reach the DHCP server, resulting in bare metal provisioning (BMP) failure.
PAGE 316
show config Configuration Tasks To configure DHCP, an administrator must first set up a DHCP server and provide it with configuration parameters and policy information including IP address ranges, lease length specifications, and configuration data that DHCP hosts need. Configuring the Dell system to be a DHCP server is a three-step process: 1. Configuring the Server for Automatic Address Allocation 2. Specifying a Default Gateway 3. Enable the system to be a DHCP server (no disable command).
PAGE 317
domain-name name 2. Specify in order of preference the DNS servers that are available to a DHCP client. DHCP Mode dns-server address Using NetBIOS WINS for Address Resolution Windows internet naming service (WINS) is a name resolution service that Microsoft DHCP clients use to correlate host names to IP addresses within a group of networks. Microsoft DHCP clients can be one of four types of NetBIOS nodes: broadcast, peer-to-peer, mixed, or hybrid. 1.
PAGE 318
• EXEC Privilege mode. clear ip dhcp binding Clear a DHCP binding entry for an individual IP address. EXEC Privilege mode. clear ip dhcp binding ip address Configure the System to be a Relay Agent DHCP clients and servers request and offer configuration information via broadcast DHCP messages. Routers do not forward broadcasts, so if there are no DHCP servers on the subnet, the client does not receive a response to its request and therefore cannot access the network.
PAGE 319
To view the ip helper-address configuration for an interface, use the show ip interface command from EXEC privilege mode. Example of the show ip interface Command R1_E600#show ip int gig 1/3 GigabitEthernet 1/3 is up, line protocol is down Internet address is 10.11.0.1/24 Broadcast address is 10.11.0.255 Address determined by user input IP MTU is 1500 bytes Helper address is 192.168.0.1 192.168.0.
PAGE 320
DHCP Client Operation with Other Features A DHCP client also operates with the following software features. Virtual Link Trunking (VLT) A DHCP client is not supported on VLT interfaces. VLAN and Port Channels DHCP client configuration and behavior are the same on Virtual LAN (VLAN) and port-channel (LAG) interfaces as on a physical interface.
PAGE 321
Configuring Route Leaking between VRFs on DHCP Relay Agent To configure route leaking between VRFs on DHCP relay agent, include the configuration similar to the following along with your DHCP relay configuration on your system.
PAGE 322
Non-default VRF configuration for DHCPv6 helper address The ipv6 helper-address command is enhanced to provide support for configuring VRF for DHCPv6 relay helper address. To forward DHCP packets between DHCP client and server if they are from different VRFs, you should configure route leak using route map between the VRFs. For more information on configuring route leak across VRF, see DHCP Relay when DHCP Server and Client are in Different VRFs.
PAGE 323
Interface level DHCP relay source IPv4 or IPv6 configuration You can configure interface specific DHCP relay source IPv4 or IPv6 configuration. If the DHCP relay source interface is configured on the interface level, the DHCP relay forwards the packets from these interfaces to the DHCP server using the interface.
PAGE 324
Dell(conf-if-vl-4)# tagged TenGigE 1/4 Dell(conf-if-vl-4)# ip helper-address vrf vrf1 100.0.0.1 Dell(conf-if-vl-4)# ipv6 helper-address vrf vrf1 100::1 Configure Secure DHCP DHCP as defined by RFC 2131 provides no authentication or security mechanisms. Secure DHCP is a suite of features that protects networks that use dynamic address allocation from spoofing and attacks.
PAGE 325
DHCPv6 relay agent options The DHCPv6 relay agent inserts Options 18 and 37 before forwarding DHCPv6 packets to the server. These DHCPv6 options are enabled by default and are not configurable. Interface ID (Option 18) Interface on which the client-originated message is received. The interface-ID is 12 bytes long and is constructed using three ifindexes: Logical, Received, and Physical. Each of the ifindex is 4 bytes long. Remote ID (Option Identifies the host from which the message is received.
PAGE 326
DHCP Snooping in a VLT Setup In a VLT setup, the DHCP snooping binding table synchronizes between the VLT nodes. Similarly, the DAI and SAV tables also synchronize between VLT nodes. For this feature to work in a VLT setup, make sure that DHCP relay, DHCP snooping, SAV, and DAI configurations are identical between the VLT peer nodes. Enabling DHCP Snooping To enable DHCP snooping, use the following commands. 1. Enable DHCP snooping globally. CONFIGURATION mode ip dhcp snooping 2.
PAGE 327
========================================================================= 10.1.1.10 00:00:a0:00:00:00 39735 S Vl 200 Po 10 10.1.1.11 00:00:a0:00:00:00 39736 S Vl 200 Po 10 10.1.1.25 00:00:a0:00:00:00 162 D Vl 200 Po 10 The following example shows a sample output of the show ip dhcp snooping binding command for a device connected to one of the VLT peers only (orphaned). The physical interface is the one that is directly connected to the VLT peer.
PAGE 328
Broadcast An attacker can broadcast an ARP reply that specifies FF:FF:FF:FF:FF:FF as the gateway’s MAC address, resulting in all clients broadcasting all internet-bound packets. MAC flooding An attacker can send fraudulent ARP messages to the gateway until the ARP cache is exhausted, after which, traffic from the gateway is broadcast.
PAGE 329
Bypassing the ARP Inspection You can configure a port to skip ARP inspection by defining the interface as trusted, which is useful in multi-switch environments. ARPs received on trusted ports bypass validation against the binding table. All ports are untrusted by default. To bypass the ARP inspection, use the following command. • Specify an interface as trusted so that ARPs are not validated against the binding table. INTERFACE mode arp inspection-trust DAI is supported on Layer 2 and Layer 3.
PAGE 330
DHCP MAC Source Address Validation DHCP MAC source address validation (SAV) validates a DHCP packet’s source hardware address against the client hardware address field (CHADDR) in the payload. The system ensures that the packet’s source MAC address is checked against the CHADDR field in the DHCP header only for packets from snooped VLANs. • Enable DHCP MAC SAV.
PAGE 331
deny vlan 10 count (0 packets) deny vlan 20 count (0 packets) Clearing the Number of SAV Dropped Packets To clear the number of SAV dropped packets, use the clear ip dhcp snooping source-address-validation discardcounters command. Dell>clear ip dhcp snooping source-address-validation discard-counters To clear the number of SAV dropped packets on a particular interface, use the clear ip dhcp snooping source-addressvalidation discard-counters interface interface command.
PAGE 332
14 Equal Cost Multi-Path (ECMP) ECMP for Flow-Based Affinity ECMP for flow-based affinity includes link bundle monitoring. Enabling Deterministic ECMP Next Hop Deterministic ECMP next hop arranges all ECMPs in order before writing them into the content addressable memory (CAM). For example, suppose the RTM learns eight ECMPs in the order that the protocols and interfaces came up. In this case, the forwarding information base (FIB) and CAM sort them so that the ECMPs are always arranged.
PAGE 333
Link Bundle Monitoring Link bundle monitoring allows the system to monitor the use of multiple links for an uneven distribution. A global default threshold of 60% is the usage percentage for the bundle; when the system reaches this threshold, it begins monitoring the configured ECMP groups for uneven distribution. Links are monitored in 15-second intervals for three consecutive instances.
PAGE 334
CONFIGURATION ECMP-GROUP mode link-bundle-monitor enable Modifying the ECMP Group Threshold You can customize the threshold percentage for monitoring ECMP group bundles. To customize the ECMP group bundle threshold and to view the changes, use the following commands. • Modify the threshold for monitoring ECMP group bundles. CONFIGURATION mode link-bundle-distribution trigger-threshold {percent} The range is from 1 to 90%. • The default is 60%. Display details for an ECMP group bundle.
PAGE 335
In this scenario, there is an additional 40Gbps link that is sometimes activated between the routers R2 and R5. When LB is configured on the routers R2 and R3 to communicate with their EBGP peers (routers R4 and R5 respectively), router R2 advertises path X to router R1 with LB indicating that a 10Gbps link is available for communication. Also, the router R3 advertises the path X with LB indicating that a 40Gbps link is available (converted to bytes per second).
PAGE 336
R5# interface tengigbitethernet 1/1 Ip address 5.5.5.2/24 no shut interface fortGigE 1/48 ip address 3.3.3.2/24 no shut router bgp 2 maximum-paths ebgp 2 bgp dmzlink-bw neighbor 5.5.5.1 remote-as 1 neighbor 5.5.5.1 dmzlink-bw neighbor 5.5.5.1 no shutdown neighbor 3.3.3.1 remote-as 1 neighbor 3.3.3.1 dmzlink-bw Dynamic Re-calculation of Link Bankwidth The Link cost associated with a port channel interface (LAG) changes whenever a member is added or deleted.
PAGE 337
NOTE: When moving destination prefixes from the LPM to the host table, there may be a hash collision because the host table is a hash table. In this case, a workaround does not exist for programming route entries in the host table. NOTE: Before moving IPv6/128 route prefixes from the host table to the LPM table, you must enable LPM CAM partitioning for extended IPv6 prefixes. See Configuring the LPM Table for IPv6 Extended Prefixes for more information.
PAGE 338
15 FCoE Transit The Fibre Channel over Ethernet (FCoE) Transit feature is supported on Ethernet interfaces. When you enable the switch for FCoE transit, the switch functions as a FIP snooping bridge. NOTE: FIP snooping is not supported on Fibre Channel interfaces.
PAGE 339
FIP provides functionality for discovering and logging into an FCF. After discovering and logging in, FIP allows FCoE traffic to be sent and received between FCoE end-devices (ENodes) and the FCF. FIP uses its own EtherType and frame format. The following illustration shows the communication that occurs between an ENode server and an FCoE switch (FCF). The following table lists the FIP functions. Table 29.
PAGE 340
Enable FIP snooping on the switch, configure the FIP snooping parameters, and configure CAM allocation for FCoE. When you enable FIP snooping, all ports on the switch by default become ENode ports. Dynamic ACL generation on the switch operating as a FIP snooping bridge function as follows: Port-based ACLs These ACLs are applied on all three port modes: on ports directly connected to an FCF, server-facing ENode ports, and bridge-to-bridge links. Port-based ACLs take precedence over global ACLs.
PAGE 341
• • • • To assign a MAC address to an FCoE end-device (server ENode or storage device) after a server successfully logs in, set the FCoE MAC address prefix (FC-MAP) value an FCF uses. The FC-MAP value is used in the ACLs installed in bridge-to-bridge links on the switch. To provide more port security on ports that are directly connected to an FCF and have links to other FIP snooping bridges, set the FCF or Bridge-to-Bridge Port modes.
PAGE 342
• • • A switch can support a maximum eight FIP snooping VLANs. Configure at least one FCF/bridge-to-bridge port mode interface for any FIP snooping-enabled VLAN. You can configure multiple FCF-trusted interfaces in a VLAN. When you disable FIP snooping: • ACLs are not installed, FIP and FCoE traffic is not blocked, and FIP packets are not processed. • • The existing per-VLAN and FIP snooping configuration is stored. The configuration is re-applied the next time you enable the FIP snooping feature.
PAGE 343
FCoE traffic is allowed on the port only after the switch learns the FC-MAP value associated with the specified FCF MAC address and verifies that it matches the configured FC-MAP value for the FCoE VLAN. Configure a Port for a Bridge-to-FCF Link If a port is directly connected to an FCF, configure the port mode as FCF. Initially, all FCoE traffic is blocked; only FIP frames are allowed to pass.
PAGE 344
To configure FCoE transit, refer to the FCoE Transit Configuration Example NOTE: DCB/DCBx is enabled when either of these configurations is applied. 2. Save the configuration on the switch. EXEC Privilege mode. write memory 3. Reload the switch to enable the configuration. EXEC Privilege mode. reload After the switch is reloaded, DCB/DCBx is enabled. 4. Enable the FCoE transit feature on a switch. CONFIGURATION mode. feature fip-snooping 5. Enable FIP snooping on all VLANs or on a specified VLAN.
PAGE 345
Command Output show fip-snooping vlan Displays information on the FCoE VLANs on which FIP snooping is enabled. The following example shows the show fip-snooping sessions command.
PAGE 346
Field Description ENode Interface Slot/ port number of the interface connected to the ENode. FCF MAC MAC address of the FCF. VLAN VLAN ID number used by the session. FC-ID Fibre Channel session ID assigned by the FCF. The following example shows the show fip-snooping fcf command. Dell# show fip-snooping fcf FCF MAC FCF Interface VLAN FC-MAP FKA_ADV_PERIOD No.
PAGE 347
Number Number Number Number Number Number Number Number Number Number Number Number Number Number of of of of of of of of of of of of of of Enode Keep Alive VN Port Keep Alive Multicast Discovery Advertisement Unicast Discovery Advertisement FLOGI Accepts FLOGI Rejects FDISC Accepts FDISC Rejects FLOGO Accepts FLOGO Rejects CVL FCF Discovery Timeouts VN Port Session Timeouts Session failures due to Hardware Config :4416 :3136 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 The following example shows the show fip-s
PAGE 348
Field Description Number of Multicast Discovery Advertisements Number of FIP-snooped multicast discovery advertisements received on the interface. Number of Unicast Discovery Advertisements Number of FIP-snooped unicast discovery advertisements received on the interface. Number of FLOGI Accepts Number of FIP FLOGI accept frames received on the interface. Number of FLOGI Rejects Number of FIP FLOGI reject frames received on the interface.
PAGE 349
FCoE Transit Configuration Example The following illustration shows an core switch used as a FIP snooping bridge for FCoE traffic between an ENode (server blade) and an FCF (ToR switch). The ToR switch operates as an FCF and FCoE gateway. Figure 39. Configuration Example: FIP Snooping on an Core Switch In this example, DCBx and PFC are enabled on the FIP snooping bridge and on the FCF ToR switch.
PAGE 350
NOTE: Configuring an FC-MAP value is only required if you do not use the default FC-MAP value (0x0EFC00). Example of Configuring the ENode Server-Facing Port Dell(conf)# interface tengigabitethernet 0/1 Dell(conf-if-te-0/1)# portmode hybrid Dell(conf-if-te-0/1)# switchport Dell(conf-if-te-0/1)# protocol lldp Dell(conf-if-te-0/1-lldp)# dcbx port-role auto-downstream NOTE: A port is enabled by default for bridge-ENode links.
PAGE 351
16 FIPS Cryptography Federal information processing standard (FIPS) cryptography provides cryptographic algorithms conforming to various FIPS standards published by the National Institute of Standards and Technology (NIST), a non-regulatory agency of the US Department of Commerce. FIPS mode is also validated for numerous platforms to meet the FIPS-140-2 standard for a software-based cryptographic module. This chapter describes how to enable FIPS cryptography requirements on Dell Networking platforms.
PAGE 352
• • • All open SSH and Telnet sessions, as well as all SCP and FTP file transfers, are closed. Any existing host keys (both RSA and RSA1) are deleted from system memory and NVRAM storage. FIPS mode is enabled. • • If you enable the SSH server when you enter the fips mode enable command, it is re-enabled for version 2 only. If you re-enable the SSH server, a new RSA host key-pair is generated automatically. You can also manually create this key-pair using the crypto key generate command.
PAGE 353
FIPS Mode Burned In MAC No Of MACs ... : enabled : 00:01:e8:8a:ff:0c : 3 Disabling FIPS Mode The following describes disabling FIPS mode. When you disable FIPS mode, the following changes occur: • • • • • • • The SSH server disables. All open SSH and Telnet sessions, as well as all SCP and FTP file transfers, close. Any existing host keys (both RSA and RSA1) are deleted from system memory and NVRAM storage. FIPS mode disables. The SSH server re-enables.
PAGE 354
17 Flex Hash and Optimized Boot-Up This chapter describes the Flex Hash and fast-boot enhancements. Topics: • • • • • • • • Flex Hash Capability Overview Configuring the Flex Hash Mechanism LACP Fast Switchover Configuring LACP Fast Switchover LACP RDMA Over Converged Ethernet (RoCE) Overview Sample Configurations Preserving 802.
PAGE 355
Dell(conf)# load-balance flexhash ipv4/ipv6 ip-proto offset1 [offset2 ] To delete the configured flex hash setting, use the no version of the command. LACP Fast Switchover LACP Fast Switchover causes the physical ports to be aggregated faster when configured in a port-channel on both the nodes that are members of a port-channel.
PAGE 356
• Lossless connectivity: VMs require the connectivity to the storage network to be lossless always. When a planned upgrade of the network nodes happens, especially with top-of-rack (ToR) nodes where there is a single point of failure for the VMs, disk I/O operations are expected to occur in 20 seconds. If disk in not accessible in 20 seconds, unexpected and undefined behavior of the VMs occurs.
PAGE 357
iscsi enable ! interface TenGigabitEthernet 0/1 Description Link to RoCE Adapter no ip address mtu 9216 portmode hybrid switchport no spanning-tree ! protocol lldp dcbx port-role auto-downstream no shutdown ! interface fortyGigE 0/33 Description “To C9010s” no ip address mtu 9216 ! port-channel-protocol LACP port-channel 1 mode active ! protocol lldp no advertise dcbx-tlv ets-reco dcbx port-role auto-upstream no shutdown C9010 1 and C9010 2, VLT, RoCE, and iSCSI ! dcb-map converged Description DCB map for C
PAGE 358
no ip address mtu 9216 channel-member fortyGigE 1/4 no shutdown interface fortyGigE 1/4 no ip address mtu 9216 dcb-map Converged protocol lldp no shutdown C9010 2 vlt domain 2 peer-link port-channel 128 back-up destination interface Port-channel 128 no ip address mtu 9216 channel-member fortyGigE 1/4 no shutdown interface fortyGigE 1/4 no ip address mtu 9216 dcb-map Converged protocol lldp no shutdown Description from MXL B1 Switch no ip address mtu 9216 dcb-map RoCE ! port-channel-proto
PAGE 359
! interface TenGigabitEthernet 0/22 Description SOFS- iSCSI no ip address mtu 9216 portmode hybrid switchport spanning-tree rstp edge-port spanning-tree 0 portfast dcb-map iSCSI ! protocol lldp no shutdown Preserving 802.1Q VLAN Tag Value for Lite Subinterfaces All the frames in a Layer 2 VLAN are identified using a tag defined in the IEEE 802.1Q standard to determine the VLAN to which the frames or traffic are relevant or associated. Such frames are encapsulated with the 802.1Q tags.
PAGE 360
18 Force10 Resilient Ring Protocol (FRRP) Force10 resilient ring protocol (FRRP) provides fast network convergence to Layer 2 switches interconnected in a ring topology, such as a metropolitan area network (MAN) or large campuses. FRRP is similar to what can be achieved with the spanning tree protocol (STP), though even with optimizations, STP can take up to 50 seconds to converge (depending on the size of network and node of failure) may require 4 to 5 seconds to reconverge.
PAGE 361
Ring Status The ring failure notification and the ring status checks provide two ways to ensure the ring remains up and active in the event of a switch or port failure. Ring Checking At specified intervals, the Master node sends a ring health frame (RHF) through the ring. If the ring is complete, the frame is received on its secondary port and the Master node resets its fail-period timer and continues normal operation.
PAGE 362
• • • • • • • • One Master node per ring — all other nodes are Transit. Each node has two member interfaces — primary and secondary. There is no limit to the number of nodes on a ring. Master node ring port states — blocking, pre-forwarding, forwarding, and disabled. Transit node ring port states — blocking, pre-forwarding, forwarding, and disabled. STP disabled on ring interfaces. Master node secondary port is in blocking state during Normal operation.
PAGE 363
Concept Explanation Ring Status The state of the FRRP ring. During initialization/configuration, the default ring status is Ring-down (disabled). The Primary and Secondary interfaces, control VLAN, and Master and Transit node information must be configured for the ring to be up. • • Ring HealthCheck Frame (RHF) Ring-Up — Ring is up and operational. Ring-Down — Ring is broken or not set up. The Master node generates two types of RHFs.
PAGE 364
• Member VLANs across multiple rings are not supported in Master nodes. To create the control VLAN for this FRRP group, use the following commands on the switch that is to act as the Master node. 1. Create a VLAN with this ID number. CONFIGURATION mode. interface vlan vlan-id VLAN ID: from 1 to 4094. 2. Tag the specified interface or range of interfaces to this VLAN. CONFIG-INT-VLAN mode.
PAGE 365
Interface: • Slot/Port, range: Slot and Port ID for the interface. The range is entered Slot/Port-Port. • • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. 3. Assign the Primary and Secondary ports and the Control VLAN for the ports on the ring. CONFIG-FRRP mode.
PAGE 366
CONFIG-FRRP mode. show configuration Viewing the FRRP Information To view general FRRP information, use one of the following commands. • Show the information for the identified FRRP group. EXEC or EXEC PRIVELEGED mode. show frrp ring-id • Ring ID: the range is from 1 to 255. Show the state of all FRRP groups. EXEC or EXEC PRIVELEGED mode. show frrp summary Ring ID: the range is from 1 to 255. Troubleshooting FRRP To troubleshoot FRRP, use the following information.
PAGE 367
secondary TengigabitEthernet 1/34 control-vlan 101 member-vlan 201 mode master no disable Example of R2 TRANSIT interface TengigabitEthernet 2/14 no ip address switchport no shutdown ! interface TengigabitEthernet 2/31 no ip address switchport no shutdown ! interface Vlan 101 no ip address tagged TengigabitEthernet 2/14,31 no shutdown ! interface Vlan 201 no ip address tagged TengigabitEthernet 2/14,31 no shutdown ! protocol frrp 101 interface primary TengigabitEthernet 2/14 secondary TengigabitEthernet 2/3
PAGE 368
You can configure a simple FRRP ring that connects a VLT device in one data center to a VLT devices in two or more Data Centers. NOTE: This configuration connects VLT devices across Data Centers using FRRP; however, the VLTi may or may not participate as a ring interface of any FRRP ring. Following figure shows a simple FRRP ring inter-connecting VLT device: Figure 41.
PAGE 369
As a result of the VLT Node1 configuration on R2, the FRRP ring R2 becomes active. The primary interface VLTi and the secondary interface P1 act as forwarding ports for the member VLANs (M11 to Mn). VLT Node2 is the master node. The primary interface for VLT Node2 is VLTi. P2 is the secondary interface, which is one of the orphan port participating in the FRRP ring. V1 is the control VLAN through which the RFHs are exchanged.
PAGE 370
19 GARP VLAN Registration Protocol (GVRP) GARP VLAN registration protocol (GVRP), defined by the IEEE 802.1q specification, is a Layer 2 network protocol that provides for automatic VLAN configuration of switches. GVRP-compliant switches use GARP to register and de-register attribute values, such as VLAN IDs, with each other. Typical virtual local area network (VLAN) implementation involves manually configuring each Layer 2 switch that participates in a given VLAN.
PAGE 371
Figure 43. Global GVRP Configuration Example Basic GVRP configuration is a two-step process: 1. Enabling GVRP Globally 2. Enabling GVRP on a Layer 2 Interface Related Configuration Tasks • • Configure GVRP Registration Configure a GARP Timer Enabling GVRP Globally To configure GVRP globally, use the following command. • Enable GVRP for the entire switch.
PAGE 372
To inspect the global configuration, use the show gvrp brief command. Enabling GVRP on a Layer 2 Interface To enable GVRP on a Layer 2 interface, use the following command. • Enable GVRP on a Layer 2 interface.
PAGE 373
• • Leave — When a GARP device expects to de-register a piece of attribute information, it sends out a Leave message and starts this timer. If a Join message does not arrive before the timer expires, the information is de-registered. The Leave timer must be greater than or equal to 3x the Join timer. The default is 600ms. LeaveAll — After startup, a GARP device globally starts a LeaveAll timer.
PAGE 374
20 High Availability (HA) High availability (HA) is a collection of features that preserves system continuity by maximizing uptime and minimizing packet loss during system disruptions.
PAGE 375
RPM Online Insertion Dell Networking systems can function with only one RPM. If you insert a second RPM, it comes online as the standby RPM. To display the status of installed RPMs, enter the show rpm all command.
PAGE 376
To replace a line card with a different card type, remove the card and then remove the existing line-card configuration for the slot using the command no linecard slot-id provision. Dell(conf)# no linecard 3 provision If you do not remove the existing line-card configuration, the status of the newly installed line card displays as mismatch card type.
PAGE 377
• • • • Border gateway protocol Open shortest path first Protocol independent multicast — sparse mode Intermediate system to intermediate system Software Resiliency During normal operations, the Dell Networking OS monitors the health of both hardware and software components in the background to identify potential failures, even before these failures manifest. System Health Monitoring The Dell Networking OS also monitors the overall health of the system.
PAGE 378
Table 36. Commands to configure Control Plane redundancy Command Description redundancy auto-failoverlimit Limits the number of failovers for a specific period. redundancy primary (rpm0 | rpm1) Select preferred RPM as primary. redundancy disable-autoreboot pe all Prevents all the PEs from automatically rebooting when the switch fails. redundancy disable-autoreboot pe id stack-unit Prevents all the PEs in a stack from automatically rebooting when the switch fails.
PAGE 379
RPM Synchronization Data between the primary (management) and standby RPMs is synchronized immediately after bootup. After the two RPMs have performed an initial full synchronization (block sync), the system automatically updates only changed data (incremental sync). The data that is synchronized consists of configuration data, operational data, state and status, and statistics depending on the version of the Dell Networking OS.
PAGE 380
21 Internet Group Management Protocol (IGMP) Internet group management protocol (IGMP) is a Layer 3 multicast protocol that hosts use to join or leave a multicast group. Multicast is premised on identifying many hosts by a single destination IP address; hosts represented by the same IP address are a multicast group. Multicast routing protocols (such as protocol-independent multicast [PIM]) use the information in IGMP messages to discover which groups are active and to populate the multicast routing table.
PAGE 381
Figure 44. IGMP Messages in IP Packets Join a Multicast Group There are two ways that a host may join a multicast group: it may respond to a general query from its querier or it may send an unsolicited report to its querier. Responding to an IGMP Query The following describes how a host can join a multicast group. 1. One router on a subnet is elected as the querier. The querier periodically multicasts (to all-multicast-systems address 224.0.0.1) a general query to all hosts on the subnet. 2.
PAGE 382
• • To enable filtering, routers must keep track of more state information, that is, the list of sources that must be filtered. An additional query type, the Group-and-Source-Specific Query, keeps track of state changes, while the Group-Specific and General queries still refresh the existing state.
PAGE 383
3. The host’s third message indicates that it is only interested in traffic from sources 10.11.1.1 and 10.11.1.2. Because this request again prevents all other sources from reaching the subnet, the router sends another group-and-source query so that it can satisfy all other hosts. There are no other interested hosts so the request is recorded. Figure 47.
PAGE 384
Figure 48. Membership Queries: Leaving and Staying Configure IGMP Configuring IGMP is a two-step process. 1. Enable multicast routing using the ip multicast-routing command. 2. Enable a multicast routing protocol.
PAGE 385
• View IGMP-enabled interfaces. EXEC Privilege mode show ip igmp interface Dell(conf-if-te-1/0)#show ip igmp interface tengigabitethernet 1/0 TenGigabitEthernet 1/0 Inbound IGMP access group is not set Internet address is 1.1.1.1/24 IGMP is up on the interface IGMP query interval is 60 seconds IGMP querier timeout is 0 seconds IGMP max query response time is 10 seconds IGMP last member query response interval is 1000 ms IGMP immediate-leave is disabled IGMP activity: 0 joins IGMP querying router is 1.1.1.
PAGE 386
Enabling IGMP Immediate-Leave If the querier does not receive a response to a group-specific or group-and-source query, it sends another (querier robustness value). Then, after no response, it removes the group from the outgoing interface for the subnet. IGMP immediate leave reduces leave latency by enabling a router to immediately delete the group membership on an interface after receiving a Leave message (it does not send any group-specific or group-and-source queries before deleting the entry).
PAGE 387
• Configuring the Switch as Querier Dell(conf)#ip igmp snooping enable Dell(conf)#do show running-config igmp ip igmp snooping enable Dell(conf)# Removing a Group-Port Association To configure or view the remove a group-port association feature, use the following commands. • Configure the switch to remove a group-port association after receiving an IGMP Leave message. • INTERFACE VLAN mode ip igmp fast-leave View the configuration.
PAGE 388
Configuring the Switch as Querier To configure the switch as a querier, use the following command. Hosts that do not support unsolicited reporting wait for a general query before sending a membership report. When the multicast source and receivers are in the same VLAN, multicast traffic is not routed and so there is no querier. Configure the switch to be the querier for a VLAN so that hosts send membership reports and the switch can generate a forwarding table by snooping.
PAGE 389
22 Interfaces This chapter describes interface types, both physical and logical, and how to configure them on the switch. • 1-Gigabit Ethernet, 10-Gigabit Ethernet and 40-Gigabit Ethernet interfaces are supported on the C9010 switch and 1-Gigabit Ethernet C1048P port extender.
PAGE 390
• • • • • • • • • • • • • • • Monitoring and Maintaining Interfaces Displaying Traffic Statistics on HiGig Ports Link Bundle Monitoring Monitoring HiGig Link Bundles Non Dell-Qualified Transceivers Splitting QSFP Ports to SFP+ Ports Configuring wavelength for 10–Gigabit SFP+ optics Link Dampening Using Ethernet Pause Frames for Flow Control Configure the MTU Size on an Interface Auto-Negotiation on Ethernet Interfaces Provisioning Combo Ports View Advanced Interface Information Configuring the Traffic Samp
PAGE 391
On the C9010, port interface numbers are written above the ports. The following examples show port numbering on C9010 line cards (40GbE QSFP+, 1/10GbE SFP+, and 1/10GbE RJ-45). Figure 50. 40GbE QSFP+ Port Numbering On the 6-Port 40GbE QSFP+ line card, ports are numbered from 0 to 5 and operate by default in 40GbE mode. If you use a breakout cable, each port can operate in 10G mode. 40GbE ports are numbered in multiples of four, starting with zero; for example, 0, 4, 8, 12, and so on.
PAGE 392
Figure 53. C1048P Port Numbering On a C1048P port extender, 10/100/1000BASE-T ports on the front panel are numbered from 1 to 48. • • • Odd-numbered ports 1-47 are on top; even-numbered ports 2-48 are on the bottom. A yellow PE port number indicates that the port is PoE-enabled. The two 10GbE SFP+ ports, which are used only for uplinks to an attached C9010, are numbered 1 and 2.
PAGE 393
Interface Type Modes Possible Default Mode Requires Creation Default State reserved VLANs. You cannot configure these VLANs. View Basic Interface Information To view basic interface information, use the following command. You have several options for viewing interface status and configuration parameters. • Lists all configurable interfaces on the chassis.
PAGE 394
PE-ID/UNIT/PORT PE Gigabit Ethernet interface Dell#show interface peGigE 255/1/1 peGigE 255/1/1 is up, line protocol is up Hardware is DellEth, address is 6c:c0:00:43:09:91 Current address is 6c:c0:00:43:09:91 Pluggable media not present Interface index is 804323335 Internet address is not set Mode of IPv4 Address Assignment : NONE DHCP Client-ID :6cc000430991 MTU 1554 bytes, IP MTU 1500 bytes LineSpeed auto, Mode auto Auto-mdix enabled, ARP type: ARPA, ARP Timeout 04:00:00 Last clearing of "show interfac
PAGE 395
Te 2/16 Te 2/17 Te 2/18 Te 2/19 Te 2/20 Te 2/21 Te 2/22 Te 2/23 Fo 5/0 Fo 5/4 Fo 5/8 Fo 5/12 Fo 5/16 Fo 5/20 Te 6/0 Te 6/1 Te 6/2 Te 6/3 Te 6/4 Te 6/5 Te 6/6 Te 6/7 Te 6/8 Te 6/9 Te 6/10 Te 6/11 Te 6/12 Te 6/13 Te 6/14 Te 6/15 Te 6/16 Te 6/17 Te 6/18 Te 6/19 Te 6/20 Te 6/21 Te 6/22 Te 6/23 Fo 9/0 Fo 9/4 Fo 9/8 Fo 9/12 Fo 9/16 Fo 9/20 Te 10/0 Te 10/1 Te 10/2 Te 10/3 Te 11/0 Te 11/1 Te 11/2 Te 11/3 PeGi 255/1/1 PeGi 255/1/2 PeGi 255/1/3 PeGi 255/1/4 PeGi 255/1/5 PeGi 255/1/6 PeGi 255/1/7 PeGi 255/1/8 PeGi 255
PAGE 396
PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi 396 255/1/22 255/1/23 255/1/24 255/1/25 255/1/26 255/1/27 255/1/28 255/1/29 255/1/30 255/1/31 255/1/32 255/1/33 255/1/34 255/1/35 255/1/36 255/1/
PAGE 397
PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi PeGi 255/2/47 255/2/48 255/3/1 255/3/2 255/3/3 255/3/4 255/3/5 255/3/6 255/3/7 255/3/8 255/3/9 255/3/10 255/3/11 255/3/12 255/3/13 255/3/14 255/3/15 255/3/16 255/3/17 255/3/18 255/3/19 255/3/20 255/3/21 255/3/22 255/3/23 255/3/24 255/3/25 255/3/26 255/3/27 255/3/28
PAGE 398
To determine which physical interfaces are available, use the show running-config command in EXEC mode. This command displays all physical interfaces available on the line cards. Dell#show running Current Configuration ...
PAGE 399
Enabling a Physical Interface After determining the type of physical interfaces available, to enable and configure the interfaces, enter INTERFACE mode by using the interface interface {slot/port | pe-id/stack-unit/port} command. 1. Enter the keyword interface then the type of interface and slot/port information. CONFIGURATION mode interface interface • • • • • For the Management interface, enter the keyword ManagementEthernet then the slot/port information.
PAGE 400
5. Set the local port speed. INTERFACE mode speed {10 | 100 | 1000 | 10000 | auto} NOTE: If you use an active optical cable (AOC), you can convert the QSFP+ port to a 10 Gigabit SFP+ port or 1 Gigabit SFP port. You can use the speed command to enable the required speed. 6. Disable auto-negotiation on the port. INTERFACE mode no negotiation auto If the speed was set to 1000, do not disable auto-negotiation. 7. Verify configuration changes.
PAGE 401
• Enable Layer 2 data transmissions through an individual interface. INTERFACE mode switchport Dell(conf-if)#show config ! interface Port-channel 1 no ip address switchport no shutdown Dell(conf-if)# Configuring Layer 2 (Interface) Mode To configure an interface in Layer 2 mode, use the following commands. • Enable the interface. • INTERFACE mode no shutdown Place the interface in Layer 2 (switching) mode.
PAGE 402
Configuring Layer 3 (Interface) Mode To assign an IP address, use the following commands. • Enable the interface. • INTERFACE mode no shutdown Configure a primary IP address and mask on the interface. INTERFACE mode ip address ip-address mask [secondary] The ip-address must be in dotted-decimal format (A.B.C.D) and the mask must be in slash format (/xx). Add the keyword secondary if the IP address is the interface’s backup IP address. You can only configure one primary IP address per interface.
PAGE 403
management egress-interface-selection 2. Configure which applications uses EIS. EIS mode application {all | application-type} NOTE: If you configure SNMP as the management application for EIS and you add a default management route, when you perform an SNMP walk and check the debugging logs for the source and destination IPs, the SNMP agent uses the destination address of incoming SNMP packets as the source address for outgoing SNMP responses for security.
PAGE 404
Last clearing of "show interface" counters 00:06:14 Queueing strategy: fifo Input 791 packets, 62913 bytes, 775 multicast Received 0 errors, 0 discarded Output 21 packets, 3300 bytes, 20 multicast Output 0 errors, 0 invalid protocol Time since last interface status change: 00:06:03 Unless you configure the management route command, you can only access the Management interface from the local LAN.
PAGE 405
Destination ----------C 6.1.1.0/24 C 10.1.1.0/24 *S 0.0.0.0/0 00:01:12 Dell# Gateway ------Direct, Fo 2/12 Direct, Vl 10 via 6.1.1.1, Fo 2/12 Dist/Metric ----------0/0 0/0 0/0 Last Change ----------00:01:12 01:09:08 Port Extender Interfaces You can use a C9010 switch with an attached C1048P, N20xx or N30xx port extender (PE) to expand the port density of the chassis. In this configuration, the C9010 operates as a controlling bridge for the C1048P, N20xx or N30xx.
PAGE 406
To assign an IP address to an interface, use the following command. • Configure an IP address and mask on the interface. INTERFACE mode ip address ip-address mask [secondary] • • ip-address mask: enter an address in dotted-decimal format (A.B.C.D). The mask must be in slash format (/24). secondary: the IP address is the interface’s backup IP address. You can configure up to eight secondary IP addresses. interface Vlan 10 ip address 1.1.1.
PAGE 407
Use the port-delay-restore command and ensure to specify a value between 1 second and 300 seconds. DellEMC(conf)#port-delay-restore 300 Use the no port-delay-restore command to disable the feature. DellEMC(conf)#no port-delay-restore If you would like to turn this feature off for an individual interface, enter the INTERFACE mode and use the no port-delay-restore command. DellEMC(config-if)#no port-delay-restore NOTE: • This command does not work on the Port Extender ports.
PAGE 408
Member ports of a LAG are added and programmed into the hardware in a predictable order based on the port ID, instead of in the order in which the ports come up. With this implementation, load balancing yields predictable results across line card resets and chassis reloads. A physical interface can belong to only one port channel at a time. Each port channel must contain interfaces of the same interface type/speed. Port channels can contain a mix of 10 or 40 Gigabit Ethernet interfaces.
PAGE 409
Adding a Physical Interface to a Port Channel The physical interfaces in a port channel can be on any line card in the chassis, but must be the same physical type. You can add any physical interface to a port channel if the interface configuration is minimal.
PAGE 410
Interface index is 1258348032 Minimum number of links to bring Port-channel up is 1 Internet address is not set Mode of IPv4 Address Assignment : NONE DHCP Client-ID :3417eb002191 MTU 1554 bytes, IP MTU 1500 bytes LineSpeed 6000 Mbit Members in this channel: PeGi 255/1/36(U) PeGi 255/1/37(U) PeGi 255/2/38(U) PeGi 255/2/39(U) PeGi 255/3/40(U) PeGi 255/3/45(U) ARP type: ARPA, ARP Timeout 04:00:00 Queueing strategy: fifo Input Statistics: 729669643 packets, 95294971809 bytes 3845 64-byte pkts, 669214494 over 6
PAGE 411
channel-member interface The following example shows moving the TengigabitEthernet 1/8 interface from port channel 4 to port channel 3.
PAGE 412
Assigning an IP Address to a Port Channel You can assign an IP address to a port channel and use port channels in Layer 3 routing protocols. To assign an IP address, use the following command. • Configure an IP address and mask on the interface. INTERFACE mode ip address ip-address mask [secondary] • • ip-address mask: enter an address in dotted-decimal format (A.B.C.D). The mask must be in slash format (/24). secondary: the IP address is the interface’s backup IP address.
PAGE 413
CONFIGURATION mode hash-algorithm ecmp {crc-upper} | {dest-ip} | {lsb} Dell(conf)#hash-algorithm ecmp xor1 lag crc16 Dell(conf)# The hash-algorithm command is specific to ECMP group. The default ECMP hash configuration is crc-lower. This command takes the lower 32 bits of the hash key to compute the egress port. Other options for ECMP hash-algorithms are: • • • crc-upper — uses the upper 32 bits of the hash key to compute the egress port. dest-ip — uses destination IP address as part of the hash key.
PAGE 414
The following is an example of single range on PE ports. Dell(config)#interface range peGigE 1/0/4-47 Dell(conf-if-range-pegi-1/0/4-47)# no shut Dell(conf-if-range-pegi-1/0/4-47)# Create a Multiple-Range The following is an example of multiple range.
PAGE 415
Also, you can associate a static multicast MAC address with one or more VLANs and port interfaces by using the mac-address-table static multicast-mac-address vlan vlan-id output-range interface command. Defining Interface Range Macros You can define an interface-range macro to automatically select a range of interfaces for configuration. Before you can use the macro keyword in the interface-range macro command string, define the macro. To define an interface-range macro, use the following command.
PAGE 416
• • • c — Clear screen a — Page down q — Quit Dell#monitor interface te 3/1 FTOS uptime is 1 day(s), 4 hour(s), 31 minute(s) Monitor time: 00:00:00 Refresh Intvl.
PAGE 417
Displaying Traffic Statistics on HiGig Ports You can verify the buffer usage and queue counters for high-Gigabit Ethernet (HiGig) ports and link bundles (port channels). The buffer counters supported for front-end ports are extended to HiGig backplane ports. You can display the queue statistics and buffer counters for backplane line-card (leaf) and switch fabric module (SFM - spine) NPU port queues on a switch using the show commands described in this section.
PAGE 418
Monitoring HiGig Link Bundles You can monitor the HiGig link bundles that transmit data between internal backplane ports on line-card (leaf) and switch fabric module (SFM - spine) network processing units (NPUs) and generate a system log message or SNMP trap when traffic distribution in a link bundle is uneven. Each NPU is a Trident chip. On the switch, backplane port channels operate as HiGig link bundles to transmit data traffic between line-card and SFM NPUs. There are 11 line-card and 2 SFM NPUs.
PAGE 419
• The trigger threshold specifies the percentage of total bundle bandwidth used to issue an alarm for uneven traffic distribution. The default is 60 percent. When the mean link utilization is below this value, uneven link-bundle traffic is not reported. The difference in utilization percentage between the high-used link and low-used link determines the alarm condition. Alarm reporting for link-bundle monitoring is based on the same algorithm used for LAG/ECMP.
PAGE 420
If you use any of the transceivers in the preceding list that is not Dell-qualified, Dell Networking OS places the interface in error-disabled (operationally down) state.
PAGE 421
NOTE: You can use the QSA adaptor to establish connectivity between a high-density 100 Gigabit platform and a relatively lower-end 1 Gigabit switch or a server. The QSA acts as an interface between the QSFP28 ports (that support 100 Gigabit speeds) and SPF optics with a maximum speed of 1 Gigabit per second. Depending on the type of optics you plug into the QSA connected to a 100 Gigabit port, the system automatically detects the supported speed of the optics and sets the interface speed accordingly.
PAGE 422
interface is deemed to be “down.” After the interface becomes stable and the penalty decays below a certain threshold, the interface comes up again and the routing protocols re-converge. Link dampening: • • • reduces processing on the CPUs by reducing excessive interface flapping. improves network stability by penalizing misbehaving interfaces and redirecting traffic. improves convergence times and stability throughout the network by isolating failures so that disturbances are not propagated.
PAGE 423
Clearing Dampening Counters To clear dampening counters and accumulated penalties, use the following command. • Clear dampening counters.
PAGE 424
rx on: Processes the received flow control frames on this port. rx off: Ignores the received flow control frames on this port. tx on: Sends control frames from this port to the connected device when a higher rate of traffic is received. tx off: Flow control frames are not sent from this port to the connected device when a higher rate of traffic is received. monitor session-ID: Enables mirror flow control frames on this port.
PAGE 425
Pause control is triggered when either the flow control buffer threshold or flow control packet pointer threshold is reached. Configure the MTU Size on an Interface If a packet includes a Layer 2 header, the difference in bytes between the link MTU and IP MTU must be enough to include the Layer 2 header.
PAGE 426
Set Auto-Negotiation Options The negotiation auto command provides a mode option for configuring an individual port to forced master/ forced slave once autonegotiation is enabled. CAUTION: Ensure that only one end of the node is configured as forced-master and the other is configured as forcedslave. If both are configured the same (that is, both as forced-master or both as forced-slave), the show interface command flaps between an auto-neg-error and forced-master/slave states.
PAGE 427
NOTE: When the port is provisioned as fiber, the presence of copper cable is not detected by the device and hence no syslog message is displayed. View Advanced Interface Information The following options have been implemented for the show [ip | running-config] interfaces commands for (only) linecard interfaces. When you use the configured keyword, only interfaces that have non-default configurations are displayed.
PAGE 428
The bold lines shows the default value of 299 seconds, the change-rate interval of 100, and the new rate interval set to 100.
PAGE 429
The bold lines shows the default value of 299 seconds, the change-rate interval of 100, and the new rate interval set to 100.
PAGE 430
Output 100.00 Mbits/sec, 4636111 packets/sec, 10.00% of line-rate Time since last interface status change: 21:00:43 Dynamic Counters By default, counting is enabled for IPFLOW, IPACL, L2ACL, L2FIB. For the remaining applications, the system automatically turns on counting when you enable the application, and is turned off when you disable the application. NOTE: If you enable more than four counter-dependent applications on a port pipe, there is an impact on line rate performance.
PAGE 431
When you enter this command, confirm that you want Dell EMC Networking OS to clear the interface counters for that interface.
PAGE 432
23 Internet Protocol Security (IPSec) Internet protocol security (IPSec) is an end-to-end security scheme for protecting IP communications by authenticating and encrypting all packets in a communication session. Use IPSec between hosts, between gateways, or between hosts and gateways. IPSec is compatible with Telnet and FTP protocols. It supports two operational modes: Transport and Tunnel. • • Transport mode — (default) Use to encrypt only the payload of the packet. Routing information is unchanged.
PAGE 433
session-key outbound esp 257 auth encrypt match 0 tcp a::1 /128 0 a::2 /128 23 match 1 tcp a::1 /128 23 a::2 /128 0 match 2 tcp a::1 /128 0 a::2 /128 21 match 3 tcp a::1 /128 21 a::2 /128 0 match 4 tcp 1.1.1.1 /32 0 1.1.1.2 /32 23 match 5 tcp 1.1.1.1 /32 23 1.1.1.2 /32 0 match 6 tcp 1.1.1.1 /32 0 1.1.1.2 /32 21 match 7 tcp 1.1.1.1 /32 21 1.1.1.2 /32 0 3. Apply the crypto policy to management traffic.
PAGE 434
24 IPv4 Routing IPv4 routing and various IP addressing features are supported. This chapter describes the basics of domain name service (DNS), address resolution protocol (ARP), and routing principles and their implementation in the Dell Networking OS.
PAGE 435
• • • Assigning IP Addresses to an Interface (mandatory) Configuring Static Routes (optional) Configure Static Routes for the Management Interface (optional) For a complete listing of all commands related to IP addressing, refer to the Dell Networking OS Command Line Reference Guide.
PAGE 436
Configuring Static Routes A static route is an IP address that you manually configure and that the routing protocol does not learn, such as open shortest path first (OSPF). Often, static routes are used as backup routes in case other dynamically learned routes are unreachable. You can enter as many static IP addresses as necessary. To configure a static route, use the following command. • Configure a static IP address.
PAGE 437
Adding description for IPv4 and IPv6 static routes Dell EMC Networking OS provides support to add a description for the IPv4 or IPv6 static route configurations. A name option is introduced to provide the description about the static route configured. This feature enables you to segregate or distinguish between the configured IPv4 or IPv6 static routes.
PAGE 438
Enabling Directed Broadcast By default, the system drops directed broadcast packets destined for an interface. This default setting provides some protection against denial of service (DoS) attacks. To enable the switch to receive directed broadcasts, use the following command. • Enable directed broadcast. INTERFACE mode ip directed-broadcast To view the configuration, use the show config command in INTERFACE mode. Resolution of Host Names Domain name service (DNS) maps host names to IP addresses.
PAGE 439
Specifying the Local System Domain and a List of Domains If you enter a partial domain, the system can search different domains to finish or fully qualify that partial domain. A fully qualified domain name (FQDN) is any name that is terminated with a period/dot. The system searches the host table first to resolve the partial domain. The host table contains both statically configured and dynamically learnt host and IP addresses.
PAGE 440
ARP The system uses two forms of address resolution: address resolution protocol (ARP) and Proxy ARP. ARP runs over Ethernet and enables endstations to learn the MAC addresses of neighbors on an IP network. Over time, the system creates a forwarding table mapping the MAC addresses to their corresponding IP address. This table is called the ARP Cache and dynamically learned addresses are removed after a defined period of time.
PAGE 441
Protocol Address Age(min) Hardware Address Interface VLAN CPU -------------------------------------------------------------------------------Internet 10.1.2.4 17 08:00:20:b7:bd:32 Ma 1/0 CP Dell# Configuring ARP Inspection Trust Use the arp-inspection-trust command to specify a port or an interface as trusted so that ARP frames are not validated against the binding table. By default, this feature is disabled. • Enable ARP learning via gratuitous ARP.
PAGE 442
• • • • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. For a port extender (PE) Gigabit Ethernet interface enter the keyword peGigE then the pe-id/pe-stack—unit-id/port-number information. For a port extender 10-Gigabit Ethernet interface, enter the keyword peTenGigE then the pe-id / stack-unit / port-id information. For a VLAN interface, enter the keyword vlan then a number between 1 and 4094.
PAGE 443
Figure 55. ARP Learning via ARP Request with ARP Learning via Gratuitous ARP Enabled Whether you enable or disable ARP learning via gratuitous ARP, the system does not look up the target IP. It only updates the ARP entry for the Layer 3 interface with the source IP of the request. Configuring ARP Retries The number of ARP retries is user-configurable. The default backoff interval remains at 20 seconds. To set and display ARP retries, use the following commands. • Set the number of ARP retries.
PAGE 444
Enabling ICMP Unreachable Messages By default, ICMP unreachable messages are disabled. When enabled, ICMP unreachable messages are created and sent out all interfaces. To disable and re-enable ICMP unreachable messages, use the following commands. • To disable ICMP unreachable messages. • INTERFACE mode no ip unreachable Set the system to create and send ICMP unreachable messages on the interface.
PAGE 445
To enable ICMP or ICMP6 redirect messages, use the icmp6-redirect enable command. NOTE: The icmp6-redirect enable command is applicable for both ICMP and ICMP6 redirects. By default, Dell EMC Networking OS supports redirects on VLAN interfaces. For physical ports and port channel interfaces, carve the fedgovacl CAM region.
PAGE 446
25 IPv6 Routing Internet protocol version 6 (IPv6) routing is the successor to IPv4. Due to the rapid growth in internet users and IP addresses, IPv4 is reaching its maximum usage. IPv6 will eventually replace IPv4 usage to allow for the constant expansion. This chapter provides a brief description of the differences between IPv4 and IPv6, and the Dell Networking support of IPv6. This chapter is not intended to be a comprehensive description of IPv6.
PAGE 447
NOTE: As an alternative to stateless autoconfiguration, network hosts can obtain their IPv6 addresses using the dynamic host control protocol (DHCP) servers via stateful auto-configuration. NOTE: The system provides the flexibility to add prefixes on Router Advertisements (RA) to advertise responses to Router Solicitations (RS). By default, RA response messages are sent when an RS message is received. The manipulation of IPv6 stateless autoconfiguration supports the router side only.
PAGE 448
IPv6 Header Fields The 40 bytes of the IPv6 header are ordered, as shown in the following illustration. Figure 57. IPv6 Header Fields Version (4 bits) The Version field always contains the number 6, referring to the packet’s IP version. Traffic Class (8 bits) The Traffic Class field deals with any data that needs special handling. These bits define the packet priority and are defined by the packet Source. Sending and forwarding routers use this field to identify different IPv6 classes and priorities.
PAGE 449
Value Description 41 IPv6 43 Routing header 44 Fragmentation header 50 Encrypted Security 51 Authentication header 59 No Next Header 60 Destinations option header NOTE: This table is not a comprehensive list of Next Header field values. For a complete and current listing, refer to the Internet Assigned Numbers Authority (IANA) web page. Hop Limit (8 bits) The Hop Limit field shows the number of hops remaining for packet processing.
PAGE 450
This field identifies the length of the Hop-by-Hop Options header in 8-byte units, but does not include the first 8 bytes. Consequently, if the header is less than 8 bytes, the value is 0 (zero). • Options (size varies) This field can contain one or more options. The first byte if the field identifies the Option type, and directs the router how to handle the option. 00 Skip and continue processing. 01 Discard the packet.
PAGE 451
In IPv6, every interface, whether using static or dynamic address assignments, also receives a local-link address automatically in the fe80::/64 subnet. IPv6 Implementation on the Dell Networking OS The Dell Networking OS supports both IPv4 and IPv6 and both versions may be used simultaneously in your system. The following table lists the Dell Networking OS version in which an IPv6 feature became available for each platform. The sections following the table give greater detail about the feature. Table 41.
PAGE 452
Feature and Functionality Dell Networking OS Release Introduction Documentation and Chapter Location Control and Monitoring in the Dell Networking OS Command Line Reference Guide. Telnet server over IPv6 (inbound Telnet) 8.3.11 Configuring Telnet with IPv6 Control and Monitoring in the Dell Networking OS Command Line Reference Guide. Secure Shell (SSH) client support over IPv6 8.3.
PAGE 453
Path MTU Discovery IPv6 path maximum transmission unit (MTU), in accordance with RFC 1981, defines the largest packet size that can traverse a transmission path without suffering fragmentation. Path MTU for IPv6 uses ICMPv6 Type-2 messages to discover the largest MTU along the path from source to destination and avoid the need to fragment the packet. The recommended MTU for IPv6 is 1280.
PAGE 454
Figure 59. NDP Router Redirect IPv6 Neighbor Discovery of MTU Packets You can set the MTU advertised through the RA packets to incoming routers, without altering the actual MTU setting on the interface. The ipv6 nd mtu command sets the value advertised to routers. It does not set the actual MTU rate. For example, if you set ipv6 nd mtu to 1280, the interface still passes 1500-byte packets, if that is what is set with the mtu command.
PAGE 455
Debugging IPv6 RDNSS Information Sent to the Host To verify that you configured the IPv6 RDNSS information sent to the host correctly, use the debug ipv6 nd command in EXEC Privilege mode. The last three lines indicate that the IPv6 RDNSS information was configured correctly.
PAGE 456
ipv6 address 1212::12/64 ipv6 nd dns-server 1000::1 1 ipv6 nd dns-server 3000::1 1 ipv6 nd dns-server 2000::1 0 no shutdown Secure Shell (SSH) Over an IPv6 Transport Both inbound and outbound secure shell (SSH) sessions using IPv6 addressing are supported. Inbound SSH supports accessing the system through the management interface as well as through a physical Layer 3 interface. For SSH configuration details, refer to the Security chapter in the Dell Networking OS Command Line Interface Reference Guide.
PAGE 457
The total number of groups is 4. Assigning an IPv6 Address to an Interface Essentially, IPv6 is enabled on a switch simply by assigning IPv6 addresses to individual router interfaces. You can use IPv6 and IPv4 together on a system, but be sure to differentiate that usage carefully. To assign an IPv6 address to an interface, use the ipv6 address command.
PAGE 458
NOTE: IPv6 addresses are normally written as eight groups of four hexadecimal digits, where each group is separated by a colon (:). Omitting zeros is accepted as described in Addressing. SNMP over IPv6 You can configure SNMP over IPv6 transport so that an IPv6 host can perform SNMP queries and receive SNMP notifications from a device running a Dell Networking OS that supports IPv6. The SNMP-server commands for IPv6 have been extended to support IPv6.
PAGE 459
• For a VLAN interface, enter the keyword vlan then the VLAN ID.
PAGE 460
E2 - OSPF external type 2, i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, IA - IS-IS inter area, * - candidate default, Gateway of last resort is not set Destination Dist/Metric, Gateway, Last Change ----------------------------------------------------C 600::/64 [0/0] Direct, Te 0/24, 00:34:42 C 601::/64 [0/0] Direct, Te 0/24, 00:34:18 C 912::/64 [0/0] Direct, Lo 2, 00:02:33 O IA 999::1/128 [110/2] via fe80::201:e8ff:fe8b:3166, Te 0/24, 00:01:30 L fe80::/10 [0/0] Direct, Nu 0, 00:34:42 Dell#show ipv6 ro
PAGE 461
Disabling ND Entry Timeout When a peer system warmboots or performs an ISSU, the ND entries in the local system may time out resulting in traffic loss. You can configure the system to keep the learnt neighbor discovery entries stateless so that the ND entries do not time out.
PAGE 462
10. Set the router lifetime. POLICY LIST CONFIGURATION mode router—lifetime value The router lifetime range is from 0 to 9,000 seconds. 11. Apply the policy to trusted ports. POLICY LIST CONFIGURATION mode trusted-port 12. Set the maximum transmission unit (MTU) value. POLICY LIST CONFIGURATION mode mtu value 13. Set the advertised reachability time. POLICY LIST CONFIGURATION mode reachable—time value The reachability time range is from 0 to 3,600,000 milliseconds. 14.
PAGE 463
ipv6 nd ra-guard policy test device-role router hop-limit maximum 1 match ra ipv6-access-list access other-config-flag on router-preference maximum medium trusted-port Interfaces : Te 1/1 Dell# Monitoring IPv6 RA Guard To debug IPv6 RA guard, use the following command. EXEC Privilege mode debug ipv6 nd ra-guard [interface slot/port | count value] The count range is from 1 to 65534. The default is infinity.
PAGE 464
26 Intermediate System to Intermediate System The intermediate system to intermediate system (IS-IS) protocol that uses a shortest-path-first algorithm. Dell Networking supports both IPv4 and IPv6 versions of IS-IS. The IS-IS protocol standards are listed in the Standards Compliance chapter.
PAGE 465
Figure 60. ISO Address Format Multi-Topology IS-IS Multi-topology IS-IS (MT IS-IS) allows you to create multiple IS-IS topologies on a single router with separate databases. Use this feature to place a virtual physical topology into logical routing domains, which can each support different routing and security policies. All routers on a LAN or point-to-point must have at least one common supported topology when operating in Multi-Topology IS-IS mode.
PAGE 466
Graceful Restart Graceful restart is a protocol-based mechanism that preserves the forwarding table of the restarting router and its neighbors for a specified period to minimize the loss of packets. A graceful-restart router does not immediately assume that a neighbor is permanently down and so does not trigger a topology change. Normally, when an IS-IS router is restarted, temporary disruption of routing occurs due to events in both the restarting router and the neighbors of the restarting router.
PAGE 467
• • Downloads IPv6 routes to the RTM for installing in the FIB. Accepts external IPv6 information and advertises this information in the PDUs. The following table lists the default IS-IS values. Table 42.
PAGE 468
To configure IS-IS globally, use the following commands. 1. Create an IS-IS routing process. CONFIGURATION mode router isis [tag] tag: (optional) identifies the name of the IS-IS process. 2. Configure an IS-IS network entity title (NET) for a routing process. ROUTER ISIS mode net network-entity-title Specify the area address and system ID for an IS-IS routing process. The last byte must be 00. For more information about configuring a NET, see IS-IS Addressing. 3. Enter the interface configuration mode.
PAGE 469
Vlan 2 GigabitEthernet 4/22 Loopback 0 Redistributing: Distance: 115 Generate narrow metrics: Accept narrow metrics: Generate wide metrics: Accept wide metrics: Dell# level-1-2 level-1-2 none none To view IS-IS protocol statistics, use the show isis traffic command in EXEC Privilege mode.
PAGE 470
To configure wide or wide transition metric style, the cost can be between 0 and 16,777,215. Configuring IS-IS Graceful Restart To enable IS-IS graceful restart globally, use the following commands. Also, you can implement optional commands to enable the graceful restart settings. • Enable graceful restart on ISIS processes. • ROUTER-ISIS mode graceful-restart ietf Configure the time during which the graceful restart attempt is prevented.
PAGE 471
T3 Timer T3 Timeout Value T2 Timeout Value T1 Timeout Value Adjacency wait time : : : : : Operational Timer Value ====================== Current Mode/State : T3 Time left : T2 Time left : Restart ACK rcv count : Restart Req rcv count : Suppress Adj rcv count : Restart CSNP rcv count : Database Sync count : Manual 30 30 (level-1), 30 (level-2) 5, retry count: 1 30 Normal/RUNNING 0 0 (level-1), 0 0 (level-1), 0 0 (level-1), 0 0 (level-1), 0 0 (level-1), 0 0 (level-1), 0 (level-2) (level-2) (level-2) (lev
PAGE 472
• • size: the range is from 128 to 9195. The default is 1497. Set the LSP refresh interval. ROUTER ISIS mode lsp-refresh-interval seconds • • seconds: the range is from 1 to 65535. The default is 900 seconds. Set the maximum time LSPs lifetime. ROUTER ISIS mode max-lsp-lifetime seconds • seconds: the range is from 1 to 65535. The default is 1200 seconds. To view the configuration, use the show config command in ROUTER ISIS mode or the show running-config isis command in EXEC Privilege mode.
PAGE 473
The default is Level 1 and Level 2 (level-1–2) To view which metric types are generated and received, use the show isis protocol command in EXEC Privilege mode. The IS-IS matrixes settings are in bold. Example of Viewing IS-IS Metric Types Dell#show isis protocol IS-IS Router: System Id: EEEE.EEEE.EEEE IS-Type: level-1-2 Manual area address(es): 47.0004.004d.0001 Routing for area address(es): 21.2223.2425.2627.2829.3031.3233 47.0004.004d.
PAGE 474
Configuring the Distance of a Route To configure the distance for a route, use the following command. • Configure the distance for a route. ROUTER ISIS mode distance Changing the IS-Type To change the IS-type, use the following commands. You can configure the system to act as a Level 1 router, a Level 1-2 router, or a Level 2 router. To change the IS-type for the router, use the following commands. • Configure IS-IS operating level for a router.
PAGE 475
Distribute Routes Another method of controlling routing information is to filter the information through a prefix list. Prefix lists are applied to incoming or outgoing routes and routes must meet the conditions of the prefix lists or the system does not install the route in the routing table. The prefix lists are globally applied on all interfaces running IS-IS. Configure the prefix list in PREFIX LIST mode prior to assigning it to the IS-IS process.
PAGE 476
ROUTER ISIS-AF IPV6 mode distribute-list prefix-list-name out [bgp as-number | connected | ospf process-id | rip | static] You can configure one of the optional parameters: • • connected: for directly connected routes. • ospf process-id: for OSPF routes only. • rip: for RIP routes only. • static: for user-configured routes. • bgp: for BGP routes only. Deny RTM download for pre-existing redistributed IPv6 routes.
PAGE 477
redistribute {bgp as-number | connected | rip | static} [level-1 level-1-2 | level-2] [metric metric-value] [metric-type {external | internal}] [route-map map-name] Configure the following parameters: • • level-1, level-1-2, or level-2: assign all redistributed routes to a level. The default is level-2. • metric-value: the range is from 0 to 16777215. The default is 0. • metric-type: choose either external or internal. The default is internal. • map-name: enter the name of a configured route map.
PAGE 478
set-overload-bit • This setting prevents other routers from using it as an intermediate hop in their shortest path first (SPF) calculations. Remove the overload bit. ROUTER ISIS mode no set-overload-bit When the bit is set, a 1 is placed in the OL column in the show isis database command output. The overload bit is set in both the Level-1 and Level-2 database because the IS type for the router is Level-1-2. Dell#show isis database IS-IS Level-1 Link State Database LSPID LSP Seq Num LSP Checksum B233.
PAGE 479
The system displays debug messages on the console. To view which debugging commands are enabled, use the show debugging command in EXEC Privilege mode. To disable a specific debug command, enter the keyword no then the debug command. For example, to disable debugging of IS-IS updates, use the no debug isis updates-packets command. To disable all IS-IS debugging, use the no debug isis command. To disable all debugging, use the undebug all command.
PAGE 480
Beginning Metric Style Final Metric Style Resulting IS-IS Metric Value metric value is displayed in the show config and show running-config commands and is used if you change back to transition metric style. NOTE: A truncated value is a value that is higher than 63, but set back to 63 because the higher value is not supported. wide narrow transition default value (10) if the original value is greater than 63. A message is sent to the console.
PAGE 481
Beginning Metric Style Next Metric Style Resulting Metric Value Next Metric Style Final Metric Value wide transition truncated value narrow transition default value (10). A message is sent to the logging buffer transition Leaks from One Level to Another In the following scenarios, each IS-IS level is configured with a different metric style. Table 46.
PAGE 482
You can configure IPv6 IS-IS routes in one of the following three different methods: • • • Congruent Topology — You must configure both IPv4 and IPv6 addresses on the interface. Enable the ip router isis and ipv6 router isis commands on the interface. Enable the wide-metrics parameter in router isis configuration mode. Multi-topology — You must configure the IPv6 address. Configuring the IPv4 address is optional. You must enable the ipv6 router isis command on the interface.
PAGE 483
Dell(conf-router_isis)#show config ! router isis net 34.0000.0000.AAAA.00 ! address-family ipv6 unicast multi-topology exit-address-family Dell (conf-router_isis)# IS-IS Sample Configuration — Multi-topology Transition Dell(conf-if-te-3/17)#show config ! interface TenGigabitEthernet 3/17 ipv6 address 24:3::1/76 ipv6 router isis no shutdown Dell(conf-if-te-3/17)# Dell(conf-router_isis)#show config ! router isis net 34.0000.0000.AAAA.
PAGE 484
27 iSCSI Optimization This chapter describes how to configure internet small computer system interface (iSCSI) optimization, which enables quality-of-service (QoS) treatment for iSCSI traffic.
PAGE 485
NOTE: After a switch is reloaded, powercycled, or upgraded, any information exchanged during the initial handshake is not available. If the switch establishes communication after reloading, it detects that a session was in progress but could not obtain complete information for it. Any incomplete information is not available in the show commands.
PAGE 486
Parameter Default Value iSCSI CoS mode (802.1p priority queue mapping) dot1p priority 4 without the remark setting when you enable iSCSI. If you do not enable iSCSI, this feature is disabled. iSCSI CoS Packet classification When you enable iSCSI, iSCSI packets are queued based on dot1p, instead of DSCP values. VLAN priority tag iSCSI flows are assigned by default to dot1p priority 4 without the remark setting. DSCP None: user-configurable. Remark Not configured.
PAGE 487
• tcp-port-n is the TCP port number or a list of TCP port numbers on which the iSCSI target listens to requests. You can configure up to 16 target TCP ports on the switch in one command or multiple commands. The default is 860, 3260. Separate port numbers with a comma. If multiple IP addresses are mapped to a single TCP port, use the no iscsi target port tcp-port-n command to remove all IP addresses assigned to the TCP number.
PAGE 488
• • • Display information on active iSCSI sessions on the switch. show iscsi session Display detailed information on active iSCSI sessions on the switch. To display detailed information on specified iSCSI session, enter the session’s iSCSI ID. show iscsi sessions detailed [session isid] Display all globally configured non-default iSCSI settings in the current Dell Networking OS session.
PAGE 489
10.10.0.44 33345 10.10.0.101 3260 0 VLT PEER2 Session 0: -------------------------------------------------------Target:iqn.2010-11.com.ixia:ixload:iscsi-TG1 Initiator:iqn.2010-11.com.ixia.ixload:initiator-iscsi-2c Up Time:00:00:01:28(DD:HH:MM:SS) Time for aging out:00:00:09:34(DD:HH:MM:SS) ISID:806978696102 Initiator Initiator Target Target Connection IP Address TCP Port IP Address TCPPort ID 10.10.0.53 33432 10.10.0.
PAGE 490
Monitoring iSCSI Traffic Flows The switch snoops iSCSI session-establishment and termination packets by installing classifier rules that trap iSCSI protocol packets to the CPU for examination. Devices that initiate iSCSI sessions usually use well-known TCP ports 3260 or 860 to contact targets. When you enable iSCSI optimization, by default the switch identifies IP packets to or from these ports as iSCSI traffic.
PAGE 491
including jumbo frames and flow-control on all ports; no storm control and spanning-tree port fast to be enabled on the port of detection. The following syslog message is generated the first time an EqualLogic array is detected: %SYSTEM:CP %LLDP-5-LLDP_EQL_DETECTED: EqualLogic Storage Array detected on interface Te 1/ 43 • • • At the first detection of an EqualLogic array, the maximum supported MTU is enabled on all ports and port-channels (if it has not already been enabled).
PAGE 492
28 Link Aggregation Control Protocol (LACP) Introduction to Dynamic LAGs and LACP The Dell Networking OS uses LACP to create dynamic LAGs. LACP provides a standardized means of exchanging information between two systems (also called Partner Systems) and automatically establishes the LAG between the systems. The benefits and constraints of a LAG are basically the same as a port channel, as described in Port Channel Interfaces in the Interfaces chapter.
PAGE 493
• • A port in Active state can set up a port channel (LAG) with another port in Active state. A port in Active state can set up a LAG with another port in Passive state. A port in Passive state cannot set up a LAG with another port in Passive state. Configuring LACP Commands If you configure aggregated ports with compatible LACP modes (Off, Active, Passive), LACP can automatically link them, as defined in IEEE 802.3, Section 43. To configure LACP, use the following commands.
PAGE 494
The following example shows configuring a LAG interface. Dell(conf)#interface port-channel 32 Dell(conf-if-po-32)#no shutdown Dell(conf-if-po-32)#switchport The LAG is in the default VLAN. To place the LAG into a non-default VLAN, use the tagged command on the LAG. Dell(conf)#interface vlan 10 Dell(conf-if-vl-10)#tagged port-channel 32 Configuring the LAG Interfaces as Dynamic After creating a LAG, configure the dynamic LAG interfaces. To configure the dynamic LAG interfaces, use the following command.
PAGE 495
Dell# show lacp 32 Port-channel 32 admin up, oper up, mode lacp Actor System ID: Priority 32768, Address 0001.e800.a12b Partner System ID: Priority 32768, Address 0001.e801.
PAGE 496
Configuring Shared LAG State Tracking To configure shared LAG state tracking, you configure a failover group. NOTE: If a LAG interface is part of a redundant pair, you cannot use it as a member of a failover group created for shared LAG state tracking. 1. Enter port-channel failover group mode. CONFIGURATION mode port-channel failover-group 2. Create a failover group and specify the two port-channels that will be members of the group.
PAGE 497
ARP type: ARPA, ARP Timeout 04:00:00 Last clearing of "show interface" counters 00:01:28 Queueing strategy: fifo NOTE: The set of console messages shown above appear only if you configure shared LAG state tracking on that router (you can configure the feature on one or both sides of a link). For example, as previously shown, if you configured shared LAG state tracking on R2 only, no messages appear on R4 regarding the state of LAGs in a failover group.
PAGE 498
Example of Viewing a LAG Port Configuration The following example inspects a LAG port configuration on ALPHA.
PAGE 499
Figure 66.
PAGE 500
Figure 67.
PAGE 501
Figure 68.
PAGE 502
Bravo(conf-if-po-10)#switch Bravo(conf-if-po-10)#no shut Bravo(conf-if-po-10)#show config ! interface Port-channel 10 no ip address switchport no shutdown ! Bravo(conf-if-po-10)#exit Bravo(conf)#int tengig 3/21 Bravo(conf)#no ip address Bravo(conf)#no switchport Bravo(conf)#shutdown Bravo(conf-if-te-3/21)#port-channel-protocol lacp Bravo(conf-if-te-3/21-lacp)#port-channel 10 mode active Bravo(conf-if-te-3/21-lacp)#no shut Bravo(conf-if-te-3/21)#end ! interface TengigabitEthernet 3/21 no ip address ! port-ch
PAGE 503
Figure 69. Inspecting a LAG Port on BRAVO Using the show interface Command The following figure illustrates inspecting LAG 10 Using the show interfaces port-channel Command.
PAGE 504
Figure 70. Inspecting LAG 10 Using the show interfaces port-channel Command The following figure illustrates inspecting the LAG Status Using the show lacp command.
PAGE 505
Figure 71. Inspecting the LAG Status Using the show lacp command The point-to-point protocol (PPP) is a connection-oriented protocol that enables layer two links over various different physical layer connections. It is supported on both synchronous and asynchronous lines, and can operate in Half-Duplex or Full-Duplex mode. It was designed to carry IP traffic but is general enough to allow any type of network layer datagram to be sent over a PPP connection.
PAGE 506
29 Layer 2 Manage the MAC Address Table You can perform the following management tasks inr the MAC address table. • • • • Clearing the MAC Address Table Setting the Aging Time for Dynamic Entries Configuring a Static MAC Address Displaying the MAC Address Table Clearing the MAC Address Table You may clear the MAC address table of dynamic entries. To clear a MAC address table, use the following command. • Clear a MAC address table of dynamic entries.
PAGE 507
Displaying the MAC Address Table To display the MAC address table, use the following command. • Display the contents of the MAC address table. EXEC Privilege mode show mac-address-table [address | aging-time [vlan vlan-id]| count | dynamic | interface | static | vlan] • • • • • • • address: displays the specified entry. aging-time: displays the configured aging-time. count: displays the number of dynamic and static entries for all VLANs, and the total number of entries.
PAGE 508
mac learning-limit Dynamic The MAC address table is stored on the Layer 2 forwarding information base (FIB) region of the CAM. The Layer 2 FIB region allocates space for static MAC address entries and dynamic MAC address entries. When you enable MAC learning limit, entries created on this port are static by default. When you configure the dynamic option, learned MAC addresses are stored in the dynamic region and are subject to aging. Entries created before this option is set are not affected.
PAGE 509
INTERFACE mode learn-limit-violation shutdown Setting Station Move Violation Actions Station move violation actions are user-configurable. no-station-move is the default behavior. You can configure the system to take an action if a station move occurs using one the following options with the mac learning-limit command. To display a list of interfaces configured with MAC learning limit or station move violation actions, use the following commands. • Generate a system log message indicating a station move.
PAGE 510
• CONFIGURATION mode mac-address-table disable-learning lldp Disable source MAC address learning from LACP and LLDP BPDUs. CONFIGURATION mode mac-address-table disable-learning If you don’t use any option, the mac-address-table disable-learning command disables source MAC address learning from both LACP and LLDP BPDUs. Enabling port security You can enable or disable port security feature globally on the Dell EMC Networking OS.
PAGE 511
Figure 73. Configuring the mac-address-table station-move refresh-arp Command Configure Redundant Pairs Networks that employ switches that do not support the spanning tree protocol (STP) — for example, networks with digital subscriber line access multiplexers (DSLAM) — cannot have redundant links between switches because they create switching loops (as shown in the following illustration).
PAGE 512
Figure 74. Configuring Redundant Layer 2 Pairs without Spanning Tree You configure a redundant pair by assigning a backup interface to a primary interface with the switchport backup interface command. Initially, the primary interface is active and transmits traffic and the backup interface remains down. If the primary fails for any reason, the backup transitions to an active Up state. If the primary interface fails and later comes back up, it remains as the backup interface for the redundant pair.
PAGE 513
As shown in the previous illustration, interface 3/41 is a backup interface for 3/42, and 3/42 is in the Down state. If 3/41 fails, 3/42 transitions to the Up state, which makes the backup link active. A message similar to the following message appears whenever you configure a backup port.
PAGE 514
Apr 9 00:16:29: %STKUNIT0-M:CP %IFMGR-5-L2BKUP_WARN: Do not run any Layer2 protocols on Po 1 and Te 0/2 Dell(conf-if-po-1)# Far-End Failure Detection Far-end failure detection (FEFD) is a protocol that senses remote data link errors in a network. FEFD responds by sending a unidirectional report that triggers an echoed response after a specified time interval. You can enable FEFD globally or locally on an interface basis. Disabling the global FEFD configuration does not disable the interface configuration.
PAGE 515
4. If the FEFD enabled system is configured to use FEFD in Normal mode and neighboring echoes are not received after three intervals, the state changes to unknown. You can set each interval from 3 to 255 seconds. 5. If the FEFD system has been set to Aggressive mode and neighboring echoes are not received after three intervals, the state changes to Err-disabled.
PAGE 516
To display information about the state of each interface, use the show fefd command in EXEC privilege mode. Dell#show fefd FEFD is globally 'ON', interval is 3 seconds, mode is 'Normal'.
PAGE 517
• Display output whenever events occur that initiate or disrupt an FEFD enabled connection. • EXEC Privilege mode debug fefd events Provide output for each packet transmission over the FEFD enabled connection. EXEC Privilege mode debug fefd packets The following example shows the debug fefd events command.
PAGE 518
30 Link Layer Discovery Protocol (LLDP) 802.1AB (LLDP) Overview LLDP — defined by IEEE 802.1AB — is a protocol that enables a local area network (LAN) device to advertise its configuration and receive configuration information from adjacent LLDP-enabled LAN infrastructure devices. The collected information is stored in a management information base (MIB) on each device, and is accessible via simple network management protocol (SNMP).
PAGE 519
Type TLV Description — Optional Includes sub-types of TLVs that advertise specific configuration information. These sub-types are Management TLVs, IEEE 802.1, IEEE 802.3, and TIA-1057 Organizationally Specific TLVs. Figure 77. LLDPDU Frame Optional TLVs The Dell Networking OS) upports these optional TLVs: management TLVs, IEEE 802.1 and 802.3 organizationally specific TLVs, and TIA-1057 organizationally specific TLVs. Management TLVs A management TLV is an optional TLVs sub-type.
PAGE 520
Type TLV Description 7 System capabilities Identifies the chassis as one or more of the following: repeater, bridge, WLAN Access Point, Router, Telephone, DOCSIS cable device, end station only, or other. 8 Management address Indicates the network address of the management interface. The Dell Networking OS does not currently support this TLV. 127 Port-VLAN ID On Dell Networking systems, indicates the untagged VLAN to which a port belongs.
PAGE 521
• • identify physical location identify network policy LLDP-MED is designed for, but not limited to, VoIP endpoints. TIA Organizationally Specific TLVs The Dell Networking system is an LLDP-MED Network Connectivity Device (Device Type 4). Network connectivity devices are responsible for: • • transmitting an LLDP-MED capability TLV to endpoint devices storing the information that endpoint devices advertise The following table describes the five types of TIA-1057 Organizationally Specific TLVs. Table 51.
PAGE 522
Type SubType TLV Description 127 11 Inventory — Asset ID Indicates a user specified device number to manage inventory. 127 12–255 Reserved — LLDP-MED Capabilities TLV The LLDP-MED capabilities TLV communicates the types of TLVs that the endpoint device and the network connectivity device support. LLDP-MED network connectivity devices must transmit the Network Policies TLV.
PAGE 523
An integer represents the application type (the Type integer shown in the following table), which indicates a device function for which a unique network policy is defined. An individual LLDP-MED network policy TLV is generated for each application type that you specify with the CLI (Advertising TLVs). NOTE: As shown in the following table, signaling is a series of control packets that are exchanged between an endpoint device and a network connectivity device to establish and maintain a connection.
PAGE 524
using the max-milliwatts option with the power inline command. Dell Networking also honors the power value (power requirement) the powered device sends when the PE is configured with power inline mode class. Figure 81. Extended Power via MDI TLV Configure LLDP Configuring LLDP is a two-step process. 1. Enable LLDP globally. 2. Advertise TLVs out of an interface.
PAGE 525
exit hello mode multiplier no show Exit from LLDP configuration mode LLDP hello configuration LLDP mode configuration (default = rx and tx) LLDP multiplier configuration Negate a command or set its defaults Show LLDP configuration R1(conf-lldp)#exit R1(conf)#interface tengigabitethernet 1/31 R1(conf-if-te-1/31)#protocol lldp R1(conf-if-te-1/31-lldp)#? advertise Advertise TLVs disable Disable LLDP protocol on this interface end Exit from configuration mode exit Exit from LLDP configuration mode hello LLDP
PAGE 526
protocol lldp 2. Enable LLDP. PROTOCOL LLDP mode no disable Disabling and Undoing LLDP on Management Ports To disable or undo LLDP on management ports, use the following command. 1. Enter Protocol LLDP mode. CONFIGURATION mode. protocol lldp 2. Enter LLDP management-interface mode. LLDP-MANAGEMENT-INTERFACE mode. management-interface 3. Enter the disable command. LLDP-MANAGEMENT-INTERFACE mode. To undo an LLDP management port configuration, precede the relevant command with the keyword no.
PAGE 527
Figure 82. Configuring LLDP Storing and Viewing Unrecognized LLDP TLVs Dell EMC Networking OS provides support to store unrecognized (reserved and organizational specific) LLDP TLVs. Also, support is extended to retrieve the stored unrecognized TLVs using SNMP. When the incoming TLV from LLDP neighbors is not recognized, the TLV is categorized as unrecognized TLV. The unrecognized TLVs is categorized into two types: 1. Reserved unrecognized LLDP TLV 2.
PAGE 528
Viewing Unrecognized LLDP TLVs You can view or retrieve the stored unrecognized (reserved and organizational specific) TLVs using the show lldp neighbor details command. View all the LLDP TLV information including unrecognized TLVs, using the snmpwalk and snmpget commands. Viewing the LLDP Configuration To view the LLDP configuration, use the following command. • Display the LLDP configuration. CONFIGURATION or INTERFACE mode show config The following example shows viewing an LLDP global configuration.
PAGE 529
-------------------------------------------------------------------Te 1/1 TenGigabitEthernet 1/5 00:01:e8:05:40:46 Te 1/2 TenGigabitEthernet 1/6 00:01:e8:05:40:46 DellEMC(conf-if-te-1/3)# Example of Viewing Detailed Information Advertised by Neighbors DellEMC(conf)#do show lldp neighbors detail ======================================================================== Local Interface TenGigabitEthernet 1/1 has 2 neighbors Total Frames Out: 3 Total Frames In: 8 Total Neighbor information Age outs: 0 Total Mult
PAGE 530
Remote Port ID: fortyGigE 1/2/8/1 Local Port ID: TenGigabitEthernet 1/2 Locally assigned remote Neighbor Index: 1 Remote TTL: 300 Information valid for next 201 seconds Time since last information change of this neighbor: 00:01:39 UnknownTLVList: OrgUnknownTLVList: ((00-01-66),127, 4) ((00-01-66),126, 4) ((00-01-66),125, 4) ((00-01-66),124, ((00-01-66),122, 4) ((00-01-66),121, 4) ((00-01-66),120, 4) ((00-01-66),119, --------------------------------------------------------------------------Remote Chassis ID
PAGE 531
no disable R1(conf-lldp)# Configuring LLDP Notification Interval This implementation has been introduced to adhere to the IEEE 802.1AB standard. This implementation allows a user to configure the LLDP notification interval between 5 (default) and 3600 seconds. NOTE: Before implementation of this feature, notification messages were not throttled. After implementation, the system throttles the lldp notification messages by 5 seconds (default) or as configured by the user.
PAGE 532
no disable R1(conf-lldp)# Configuring a Time to Live The information received from a neighbor expires after a specific amount of time (measured in seconds) called a time to live (TTL). The TTL is the product of the LLDPDU transmit interval (hello) and an integer called a multiplier. The default multiplier is 4, which results in a default TTL of 120 seconds. • Adjust the TTL value. • CONFIGURATION mode or INTERFACE mode. multiplier Return to the default multiplier value.
PAGE 533
Figure 83. The debug lldp detail Command — LLDPDU Packet Dissection Example of debug lldp Command Output with Unrecognized Reserved and Organizational Specific LLDP TLVs The following is an example of LLDPDU with both (Reserved and Organizational specific) unrecognized TLVs.
PAGE 534
Table 55. LLDP Configuration MIB Objects MIB Object Category LLDP Variable LLDP MIB Object Description LLDP Configuration adminStatus lldpPortConfigAdminStatus Whether you enable the local LLDP agent for transmit, receive, or both. msgTxHold lldpMessageTxHoldMultiplier Multiplier value. msgTxInterval lldpMessageTxInterval Transmit Interval value. rxInfoTTL lldpRxInfoTTL Time to live for received TLVs. txInfoTTL lldpTxInfoTTL Time to live for transmitted TLVs.
PAGE 535
TLV Type 7 8 TLV Name System Capabilities Management Address TLV Variable system capabilities enabled capabilities management address length management address subtype management address interface numbering subtype interface number OID System LLDP MIB Object Remote lldpRemSysDesc Local lldpLocSysCapSupported Remote lldpRemSysCapSupported Local lldpLocSysCapEnabled Remote lldpRemSysCapEnabled Local lldpLocManAddrLen Remote lldpRemManAddrLen Local lldpLocManAddrSubtype Remote
PAGE 536
Table 58.
PAGE 537
TLV Sub-Type TLV Name TLV Variable System LLDP-MED MIB Object lldpXMedLocXPoEPDPowe rSource Remote lldpXMedRemXPoEPSEPo werSource lldpXMedRemXPoEPDPow erSource Power Priority Local lldpXMedLocXPoEPDPowe rPriority lldpXMedLocXPoEPSEPort PDPriority Remote lldpXMedRemXPoEPSEPo werPriority lldpXMedRemXPoEPDPow erPriority Power Value Local lldpXMedLocXPoEPSEPort PowerAv lldpXMedLocXPoEPDPowe rReq Remote lldpXMedRemXPoEPSEPo werAv lldpXMedRemXPoEPDPow erReq Link Layer Discovery Protocol (LLDP) 5
PAGE 538
31 Multicast Source Discovery Protocol (MSDP) This chapter describes how to configure and use the multicast source discovery protocol (MSDP). Protocol Overview MSDP is a Layer 3 protocol that connects IPv4 protocol-independent multicast-sparse mode (PIM-SM) domains. A domain in the context of MSDP is a contiguous set of routers operating PIM within a common boundary defined by an exterior gateway protocol, such as border gateway protocol (BGP).
PAGE 539
Figure 85.
PAGE 540
Implementation Information The Dell Networking OS implementation of MSDP is in accordance with RFC 3618 and Anycast RP is in accordance with RFC 3446. Configure Multicast Source Discovery Protocol Configuring MSDP is a four-step process. 1. Enable an exterior gateway protocol (EGP) with at least two routing domains. Refer to the following figures. The MSDP Sample Configurations show the OSPF-BGP configuration used in this chapter for MSDP.
PAGE 541
Figure 86.
PAGE 542
Figure 87.
PAGE 543
Figure 88.
PAGE 544
Figure 89. Configuring MSDP Enable MSDP Enable MSDP by peering RPs in different administrative domains. 1. Enable MSDP. CONFIGURATION mode ip multicast-msdp 2. Peer PIM systems in different administrative domains. CONFIGURATION mode ip msdp peer connect-source R3(conf)#ip multicast-msdp R3(conf)#ip msdp peer 192.168.0.
PAGE 545
Multicast sources in remote domains are stored on the RP in the source-active cache (SA cache). The system does not create entries in the multicast routing table until there is a local receiver for the corresponding multicast group. R3#show ip msdp peer Peer Addr: 192.168.0.1 Local Addr: 192.168.0.
PAGE 546
Enabling the Rejected Source-Active Cache To cache rejected sources, use the following command. Active sources can be rejected because the RPF check failed, the SA limit is reached, the peer RP is unreachable, or the SA message has a format error. • Cache rejected sources. CONFIGURATION mode ip msdp cache-rejected-sa Accept Source-Active Messages that Fail the RFP Check A default peer is a peer from which active sources are accepted even though they fail the RFP check.
PAGE 547
Figure 91.
PAGE 548
Figure 92.
PAGE 549
Figure 93. MSDP Default Peer, Scenario 4 Specifying Source-Active Messages To specify messages, use the following command. • Specify the forwarding-peer and originating-RP from which all active sources are accepted without regard for the RPF check. CONFIGURATION mode ip msdp default-peer ip-address list If you do not specify an access list, the peer accepts all sources that peer advertises. All sources from RPs that the ACL denies are subject to the normal RPF check. Dell(conf)#ip msdp peer 10.0.50.
PAGE 550
3 rejected SAs received, cache-size 32766 UpTime GroupAddr SourceAddr RPAddr 00:33:18 229.0.50.64 24.0.50.64 200.0.1.50 00:33:18 229.0.50.65 24.0.50.65 200.0.1.50 00:33:18 229.0.50.66 24.0.50.66 200.0.1.50 LearnedFrom 10.0.50.2 10.0.50.2 10.0.50.2 Reason Rpf-Fail Rpf-Fail Rpf-Fail Limiting the Source-Active Messages from a Peer To limit the source-active messages from a peer, use the following commands. 1. OPTIONAL: Store sources that are received after the limit is reached in the rejected SA cache.
PAGE 551
2. Prevent the system from caching remote sources learned from a specific peer based on source and group. CONFIGURATION mode ip msdp sa-filter list out peer list ext-acl As shown in the following example, R1 is advertising source 10.11.4.2. It is already in the SA cache of R3 when an ingress SA filter is applied to R3. The entry remains in the SA cache until it expires and is not stored in the rejected SA cache. [Router 3] R3(conf)#do show run msdp ! ip multicast-msdp ip msdp peer 192.168.0.
PAGE 552
To display the configured SA filters for a peer, use the show ip msdp peer command from EXEC Privilege mode. Logging Changes in Peership States To log changes in peership states, use the following command. • Log peership state changes. CONFIGURATION mode ip msdp log-adjacency-changes Terminating a Peership MSDP uses TCP as its transport protocol. In a peering relationship, the peer with the lower IP address initiates the TCP session, while the peer with the higher IP address listens on port 639.
PAGE 553
R3(conf)#do show ip msdp peer Peer Addr: 192.168.0.1 Local Addr: 0.0.0.0(0) Connect Source: Lo 0 State: Inactive Up/Down Time: 00:00:04 Timers: KeepAlive 30 sec, Hold time 75 sec SourceActive packet count (in/out): 0/0 SAs learned from this peer: 0 SA Filtering: Input (S,G) filter: myremotefilter Output (S,G) filter: none Debugging MSDP To debug MSDP, use the following command. • Display the information exchanged between peers.
PAGE 554
Figure 94. MSDP with Anycast RP Configuring Anycast RP To configure anycast RP: 1. In each routing domain that has multiple RPs serving a group, create a Loopback interface on each RP serving the group with the same IP address. CONFIGURATION mode interface loopback 2. Make this address the RP for the group. CONFIGURATION mode ip pim rp-address 3. In each routing domain that has multiple RPs serving a group, create another Loopback interface on each RP serving the group with a unique IP address.
PAGE 555
network Reducing Source-Active Message Flooding RPs flood source-active messages to all of their peers away from the RP. When multiple RPs exist within a domain, the RPs forward received active source information back to the originating RP, which violates the RFP rule. You can prevent this unnecessary flooding by creating a mesh-group. A mesh in this context is a topology in which each RP in a set of RPs has a peership with all other RPs in the set.
PAGE 556
The following shows an R2 configuration for MSDP with Anycast RP. ip multicast-routing ! interface TenGigabitEthernet 2/1 ip pim sparse-mode ip address 10.11.4.1/24 no shutdown ! interface TenGigabitEthernet 2/11 ip pim sparse-mode ip address 10.11.1.21/24 no shutdown ! interface TenGigabitEthernet 2/31 ip pim sparse-mode ip address 10.11.0.23/24 no shutdown ! interface Loopback 0 ip pim sparse-mode ip address 192.168.0.1/32 no shutdown ! interface Loopback 1 ip address 192.168.0.
PAGE 557
network 10.11.6.0/24 area 0 network 192.168.0.3/32 area 0 redistribute static redistribute connected redistribute bgp 200 ! router bgp 200 redistribute ospf 1 neighbor 192.168.0.22 remote-as 100 neighbor 192.168.0.22 ebgp-multihop 255 neighbor 192.168.0.22 update-source Loopback 0 neighbor 192.168.0.22 no shutdown ! ip multicast-msdp ip msdp peer 192.168.0.11 connect-source Loopback 0 ip msdp peer 192.168.0.22 connect-source Loopback 0 ip msdp sa-filter out 192.168.0.22 ! ip route 192.168.0.1/32 10.11.0.
PAGE 558
ip address 10.11.4.1/24 no shutdown ! interface TenGigabitEthernet 2/11 ip pim sparse-mode ip address 10.11.1.21/24 no shutdown ! interface TenGigabitEthernet 2/31 ip pim sparse-mode ip address 10.11.0.23/24 no shutdown ! interface Loopback 0 ip address 192.168.0.2/32 no shutdown ! router ospf 1 network 10.11.1.0/24 area 0 network 10.11.4.0/24 area 0 network 192.168.0.2/32 area 0 redistribute static redistribute connected redistribute bgp 100 ! router bgp 100 redistribute ospf 1 neighbor 192.168.0.
PAGE 559
ip multicast-msdp ip msdp peer 192.168.0.1 connect-source Loopback 0 ! ip route 192.168.0.2/32 10.11.0.23 MSDP Sample Configuration: R4 Running-Config ip multicast-routing ! interface TenGigabitEthernet 0/21 ip pim sparse-mode ip address 10.11.5.1/24 no shutdown ! interface TenGigabitEthernet 0/22 ip address 10.10.42.1/24 no shutdown ! interface TenGigabitEthernet 0/31 ip pim sparse-mode ip address 10.11.6.43/24 no shutdown ! interface Loopback 0 ip address 192.168.0.
PAGE 560
ip route 192.168.0.3/32 10.11.0.32 ! ip pim rp-address 192.168.0.1 group-address 224.0.0.0/4 MSDP Sample Configuration: R3 Running-Config ip multicast-routing ! interface TenGigabitEthernet 0/21 ip pim sparse-mode ip address 10.11.0.32/24 no shutdown ! interface TenGigabitEthernet 0/41 ip pim sparse-mode ip address 10.11.6.34/24 no shutdown ! interface ManagementEthernet 0/0 ip address 10.11.80.3/24 no shutdown ! interface Loopback 0 ip pim sparse-mode ip address 192.168.0.
PAGE 561
! ip pim rp-address 192.168.0.3 group-address 224.0.0.
PAGE 562
32 Multiple Spanning Tree Protocol (MSTP) Multiple spanning tree protocol (MSTP) — specified in IEEE 802.1Q-2003 — is a rapid spanning tree protocol (RSTP)-based spanning tree variation that improves on per-VLAN spanning tree plus (PVST+). MSTP allows multiple spanning tree instances and allows you to map many VLANs to one spanning tree instance to reduce the total number of required instances. Protocol Overview In contrast, PVST+ allows a spanning tree instance for each VLAN.
PAGE 563
• • MSTP Sample Configurations Debugging and Verifying MSTP Configurations Spanning Tree Variations The Dell Networking OS supports four variations of spanning tree, as shown in the following table. Table 59. Spanning Tree Variations Dell Networking Term IEEE Specification Spanning Tree Protocol (STP) 802 .1d Rapid Spanning Tree Protocol (RSTP) 802 .1w Multiple Spanning Tree Protocol (MSTP) 802 .
PAGE 564
• • Within an MSTI, only one path from any bridge to any other bridge is enabled. Bridges block a redundant path by disabling one of the link ports. 1. Enter PROTOCOL MSTP mode. CONFIGURATION mode protocol spanning-tree mstp 2. Enable MSTP. PROTOCOL MSTP mode no disable To verify that MSTP is enabled, use the show config command in PROTOCOL MSTP mode.
PAGE 565
1 100 2 200-300 To view the forwarding/discarding state of the ports participating in an MSTI, use the show spanning-tree msti command from EXEC Privilege mode. Dell#show spanning-tree msti 1 MSTI 1 VLANs mapped 100 Root Identifier has priority 32768, Address 0001.e806.953e Root Bridge hello time 2, max age 20, forward delay 15, max hops 19 Bridge Identifier has priority 32768, Address 0001.e80d.
PAGE 566
Interoperate with Non-Dell Bridges The Dell Networking OS supports only one MSTP region. A region is a combination of three unique qualities: • • • Name is a mnemonic string you assign to the region. The default region name is null. Revision is a 2-byte number. The default revision number is 0. VLAN-to-instance mapping is the placement of a VLAN in an MSTI. For a bridge to be in the same MSTP region as another, all three of these qualities must match exactly.
PAGE 567
PROTOCOL MSTP mode hello-time seconds NOTE: With large configurations (especially those configurations with more ports) Dell Networking recommends increasing the hello-time. The range is from 1 to 10. The default is 2 seconds. 3. Change the max-age parameter. PROTOCOL MSTP mode max-age seconds The range is from 6 to 40. The default is 20 seconds. 4. Change the max-hops parameter. PROTOCOL MSTP mode max-hops number The range is from 1 to 40. The default is 20.
PAGE 568
spanning-tree msti number cost cost The range is from 0 to 200000. For the default, refer to the default values shown in the table.. 2. Change the port priority of an interface. INTERFACE mode spanning-tree msti number priority priority The range is from 0 to 240, in increments of 16. The default is 128. To view the current values for these interface parameters, use the show config command from INTERFACE mode.
PAGE 569
Flush MAC Addresses after a Topology Change The system has an optimized MAC address flush mechanism for RSTP, MSTP, and PVST+ that flushes addresses only when necessary, which allows for faster convergence during topology changes. However, you may activate the flushing mechanism defined by 802.1Q-2003 using the tc-flush-standard command, which flushes MAC addresses after every topology change notification.
PAGE 570
no shutdown ! (Step 3) interface Vlan 100 no ip address tagged TenGigabitEthernet 1/21,31 no shutdown ! interface Vlan 200 no ip address tagged TenGigabitEthernet 1/21,31 no shutdown ! interface Vlan 300 no ip address tagged TenGigabitEthernet 1/21,31 no shutdown Router 2 Running-Configuration This example uses the following steps: 1. Enable MSTP globally and set the region name and revision map MSTP instances to the VLANs. 2. Assign Layer-2 interfaces to the MSTP topology. 3.
PAGE 571
3. Create VLANs mapped to MSTP instances tag interfaces to the VLANs.
PAGE 572
tagged 1/0/31 tagged 1/0/32 exit interface vlan 200 tagged 1/0/31 tagged 1/0/32 exit interface vlan 300 tagged 1/0/31 tagged 1/0/32 exit Debugging and Verifying MSTP Configurations To debut and verify MSTP configuration, use the following commands. • • Display BPDUs. EXEC Privilege mode debug spanning-tree mstp bpdu Display MSTP-triggered topology change messages.
PAGE 573
CIST Root Bridge Id: 32768:0001.e806.953e, Ext Path Cost: 0 Regional Bridge Id: 32768:0001.e806.953e, CIST Port Id: 128:470 Msg Age: 0, Max Age: 20, Hello: 2, Fwd Delay: 15, Ver1 Len: 0, Ver3 Len: 96 Name: Tahiti, Rev: 123, Int Root Path Cost: 0 Rem Hops: 20, Bridge Id: 32768:0001.e806.953e 4w0d4h : INST 1: Flags: 0x6e, Reg Root: 32768:0001.e806.953e, Int Root Cost: 0 Brg/Port Prio: 32768/128, Rem Hops: 20 INST 2: Flags: 0x6e, Reg Root: 32768:0001.e806.
PAGE 574
33 Multicast Features The Dell Networking OS supports the following multicast protocols: • • • PIM Sparse-Mode (PIM-SM) Internet Group Management Protocol (IGMP) Multicast Source Discovery Protocol (MSDP) Topics: • • • • • • • • Enabling IP Multicast Implementation Information First Packet Forwarding for Lossless Multicast Multicast Policies Understanding Multicast Traceroute (mtrace) Printing Multicast Traceroute (mtrace) Paths Supported Error Codes mtrace Scenarios Enabling IP Multicast Before enablin
PAGE 575
Dell EMC Networking OS does not support multicast routing in the following VLT scenarios: • • In a VLT enabled PIM router, multicast routing is not supported when there are multiple PIM spanned paths to reach source or RP. The workaround is to configure only one PIM spanned path to reach any PIM router in the aggregation or spine.
PAGE 576
ip multicast-limit The range if from 1 to 16000. The default is 4000. NOTE: The IN-L3-McastFib CAM partition is used to store multicast routes and is a separate hardware limit that exists per port-pipe. Any software-configured limit may supersede by this hardware space limitation. The opposite is also true, the CAM partition might not be exhausted at the time the system-wide route limit the ip multicast-limit command sets is reached.
PAGE 577
Figure 97. Preventing a Host from Joining a Group Table 61. Preventing a Host from Joining a Group — Description Location Description 1/21 • • • • Interface GigabitEthernet 1/21 ip pim sparse-mode ip address 10.11.12.1/24 no shutdown 1/31 • • • • Interface GigabitEthernet 1/31 ip pim sparse-mode ip address 10.11.13.1/24 no shutdown 2/1 • • • • Interface GigabitEthernet 2/1 ip pim sparse-mode ip address 10.11.1.
PAGE 578
Location Description • • • ip pim sparse-mode ip address 10.11.12.2/24 no shutdown 2/31 • • • • Interface GigabitEthernet 2/31 ip pim sparse-mode ip address 10.11.23.1/24 no shutdown 3/1 • • • • Interface GigabitEthernet 3/1 ip pim sparse-mode ip address 10.11.5.1/24 no shutdown 3/11 • • • • Interface GigabitEthernet 3/11 ip pim sparse-mode ip address 10.11.13.2/24 no shutdown 3/21 • • • • Interface GigabitEthernet 3/21 ip pim sparse-mode ip address 10.11.23.
PAGE 579
Preventing a Source from Registering with the RP To prevent the PIM source DR from sending register packets to RP for the specified multicast source and group, use the following command. If the source DR never sends register packets to the RP, no hosts can ever discover the source and create a shortest path tree (SPT) to it. • Prevent a source from transmitting to a particular group.
PAGE 580
Location Description • no shutdown 1/31 • • • • Interface GigabitEthernet 1/31 ip pim sparse-mode ip address 10.11.13.1/24 no shutdown 2/1 • • • • Interface GigabitEthernet 2/1 ip pim sparse-mode ip address 10.11.1.1/24 no shutdown 2/11 • • • • Interface GigabitEthernet 2/11 ip pim sparse-mode ip address 10.11.12.2/24 no shutdown 2/31 • • • • Interface GigabitEthernet 2/31 ip pim sparse-mode ip address 10.11.23.
PAGE 581
Excessive traffic is generated when the join process from the RP back to the source is blocked due to a new source group being permitted in the join-filter. This results in the new source becoming stuck in registering on the DR and the continuous generation of UDP-encapsulated registration messages between the DR and RP routers which are being sent to the CPU. • Prevent the PIM SM router from creating state based on multicast source and/ or group.
PAGE 582
Printing Multicast Traceroute (mtrace) Paths Dell Networking OS supports Multicast traceroute. MTRACE is an IGMP-based tool that prints the network path that a multicast packet takes from a source to a destination, for a particular group. Dell Networking OS has mtrace client and mtrace transit functionality. • • MTRACE Client — an mtrace client transmits mtrace queries and print the details from received responses.
PAGE 583
Command Output Description From source (?) to destination (?) In case the provided source or destination IP can be resolved to a hostname the corresponding name will be displayed. In cases where the IP cannot be resolved, it is displayed as (?) 0 1.1.1.1 --> Destination The first row in the table corresponds to the destination provided by the user. -1 1.1.1.1 PIM Reached RP/Core 103.103.103.0/24 The information in each of the response blocks is displayed as follows: • • • • • -4 103.103.103.
PAGE 584
Table 65. Mtrace Scenarios Scenario When you want to trace a route with the multicast tree for a source, group, and destination, you can specify all the parameters in the command. Mtrace will trace the complete path from source to destination by using the multicast tables for that group. You can issue the mtrace command specifying the source multicast tree and multicast group without specifying the destination. Mtrace traces the complete path traversing through the multicast group to reach the source.
PAGE 585
Scenario Output ----------------------------------------------------------------* - Any PIM enabled interface on this node R1>mtrace 103.103.103.3 1.1.1.1 Type Ctrl-C to abort. Querying reverse path for source 103.103.103.3 to destination 1.1.1.1 via RPF From source (?) to destination (?) ---------------------------------------------------------------|Hop| OIF IP |Proto| Forwarding Code |Source Network/ Mask| ---------------------------------------------------------------0 1.1.1.1 --> Destination -1 1.1.1.
PAGE 586
Scenario Output ----------------------------------------------------------------- If you invoke a weak mtrace query (without the multicast group details) and the RPF neighbor on one of the nodes to the source is not PIM enabled, the output of the command displays a NO ROUTE error code in the Forwarding Code column. In the command output, the entry for that node in the Source Network/Mask column displays the value as default.
PAGE 587
Scenario If a router in the network does not process mtrace and drops the packet resulting in no response, the system performs an expanding-hop search to trace the path to the router that has dropped mtrace. The output of the command displays a ‘*’ indicating that no response is received for an mtrace request. The following message appears when the system performs a hopby-hop search: “switching to hop-by-hop:” Output R1>mtrace 99.99.99.99 1.1.1.1 Type Ctrl-C to abort. Querying reverse path for source 99.
PAGE 588
Scenario Output -3 2.2.2.1 PIM 99.99.0.0/16 . . . -146 17.17.17.17 PIM No space in packet 99.99.0.0/16 ----------------------------------------------------------------In a valid scenario, mtrace request packets are expected to be received on the OIF of the node. However, due to incorrect formation of the multicast tree, the packet may be received on a wrong interface. In such a scenario, a corresponding error message is displayed. R1>mtrace 6.6.6.6 4.4.4.5 Type Ctrl-C to abort.
PAGE 589
34 Multicast Listener Discovery Protocol Dell Networking OS Supports Multicast Listener Discovery (MLD) protocol. Multicast Listener Discovery (MLD) is a Layer 3 protocol that IPv6 routers use to learn of the multicast receivers that are directly connected to them and the groups in which the receivers are interested. Multicast routing protocols (like PIM) use the information learned from MLD to route multicast traffic to all interested receivers.
PAGE 590
Destination Address field). To avoid duplicate reporting, any host that hears a report from another host for the same group in which it itself is interested cancels its report for that group. A host does not have to wait for a General Query to join a group. If a host wants to become a member of a group for which the router is not currently forwarding traffic, it should send an unsolicited report.
PAGE 591
| | * * | | +. -+ . . . . . . +-+ | | * * | | * Source Address [N] * | | * * | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Version 2 multicast listener reports are sent by IP nodes to report (to neighboring routers) the current multicast listening state, or changes in the multicast listening state, of their interfaces.
PAGE 592
| | * Source Address [2] * | | * * | | +-+ . . . . . . . . . +-+ | | * * | | * Source Address [N] * | | * * | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | . . . Auxiliary Data . . .
PAGE 593
Configuring MLD Version To configure MLD version on the system, follow this procedure: Select the MLD version INTERFACE Mode ipv6 mld version {1 | 2} If you do not configure the MLD version, the system defaults to version 2. The ipv6 mld version command is applicable for MLD snooping-enabled interfaces. Clearing MLD groups Clear a specific group or all groups on an interface from the multicast routing table.
PAGE 594
EXEC Privilege show ipv6 mld groups Dell#show ipv6 mld groups Total Number of Groups: 1 MLD Connected Group Membership Group Address Interface Mode Ff08::12 Vlan 10 MLDv2 Uptime 00:00:12 Expires 00:02:05 Last Reporter 1::2 Displaying MLD Interfaces Display MLD interfaces.
PAGE 595
Configure the switch as a querier Hosts that do not support unsolicited reporting wait for a general query before sending a membership report. When the multicast source and receivers are in the same VLAN, multicast traffic is not routed, and so there is no querier. You must configure the switch to be the querier for a VLAN so that hosts send membership reports, and the switch can generate a forwarding table by snooping.
PAGE 596
35 Object Tracking IPv4 or IPv6 object tracking is available on Dell Networking OS. Object tracking allows the Dell Networking operating system (OS) client processes, such as virtual router redundancy protocol (VRRP), to monitor tracked objects (for example, interface or link status) and take appropriate action when the state of an object changes.
PAGE 597
Figure 99. Object Tracking Example When you configure a tracked object, such as an IPv4 or IPv6 a route or interface, you specify an object number to identify the object. Optionally, you can also specify: • • UP and DOWN thresholds used to report changes in a route metric. A time delay before changes in a tracked object’s state are reported to a client. Track Layer 2 Interfaces You can create an object to track the line-protocol state of a Layer 2 interface.
PAGE 598
A tracked route matches a route in the routing table only if the exact address and prefix length match an entry in the routing table. For example, when configured as a tracked route, 10.0.0.0/24 does not match the routing table entry 10.0.0.0/8. If no route-table entry has the exact address and prefix length, the tracked route is considered to be DOWN.
PAGE 599
The default is 0. 4. (Optional) Identify the tracked object with a text description. OBJECT TRACKING mode description text The text string can be up to 80 characters. 5. (Optional) Configure the metric threshold for the UP and/or DOWN routing status to be tracked for the specified route. OBJECT TRACKING mode threshold metric {[up number] [down number]} The default UP threshold is 254. The routing state is UP if the scaled route metric is less than or equal to the UP threshold.
PAGE 600
delay {[up seconds] [down seconds]} Valid delay times are from 0 to 180 seconds. The default is 0. 3. (Optional) Identify the tracked object with a text description. OBJECT TRACKING mode description text The text string can be up to 80 characters. 4. (Optional) Display the tracking configuration and the tracked object’s status. EXEC Privilege mode show track object-id The following example configures object tracking on the reachability of an IPv4 route. Dell(conf)#track 104 ip route 10.0.0.
PAGE 601
For example, consider that the next-hop address is changed and the track reachability is checked after the set refresh interval (20 seconds). If the reachability to the next-hop address is failed, the system displays the following log stating that the track object state is changed from UP to DOWN. Sep 28 11:08:57 %STKUNIT1-M:CP %OTM-6-STATE: Object 2 state transition from Up to Down.
PAGE 602
Valid object IDs are from 1 to 65535. 2. (Optional) Configure the time delay used before communicating a change in the status of a tracked interface. OBJECT TRACKING mode delay {[up seconds] [down seconds]} Valid delay times are from 0 to 180 seconds. The default is 0. 3. (Optional) Identify the tracked object with a text description. OBJECT TRACKING mode description text The text string can be up to 80 characters. 4. (Optional) Display the tracking configuration and the tracked object’s status.
PAGE 603
3. (Optional) Identify the tracked object with a text description. OBJECT TRACKING mode description text The text string can be up to 80 characters. 4. (Optional) Display the tracking configuration and the tracked object’s status. EXEC Privilege mode show track object-id Example of configuring object tracking for an IPv4 interface.
PAGE 604
Displaying Tracked Objects To display the currently configured objects used to track Layer 2 and Layer 3 interfaces, and IPv4 and IPv6 routes, use the following show commands. To display the configuration and status of currently tracked Layer 2 or Layer 3 interfaces, IPv4 or IPv6 routes, or a VRF instance, use the show track command. You can also display the currently configured per-protocol resolution values used to scale route metrics when tracking metric thresholds.
PAGE 605
Example of the show track vrf command. Dell#show track vrf red Track 5 IP route 192.168.0.0/24 reachability, Vrf: red Reachability is Up (CONNECTED) 3 changes, last change 00:02:39 First-hop interface is GigabitEthernet 13/4 Example of Viewing the object tracking configuration. Dell#show running-config track track 1 ip route 23.0.0.
PAGE 606
36 Open Shortest Path First (OSPFv2 and OSPFv3) This chapter describes how to configure and use Open Shortest Path First (OSPFv2 for IPv4) and OSPF version 3 (OSPF for IPv6). NOTE: The fundamental mechanisms of OSPF (flooding, DR election, area support, SPF calculations, and so on) are the same between OSPFv2 and OSPFv3. This chapter identifies and clarifies the differences between the two versions of OSPF. Except where identified, the information in this chapter applies to both protocol versions.
PAGE 607
Figure 100. Autonomous System Areas Area Types The backbone of the network is Area 0. It is also called Area 0.0.0.0 and is the core of any AS. All other areas must connect to Area 0. Areas can be defined in such a way that the backbone is not contiguous. An OSPF backbone is responsible for distributing routing information between areas. It consists of all area border routers, networks not wholly contained in any area, and their attached routers. The backbone is the only area with a default area number.
PAGE 608
Router Types Router types are attributes of the OSPF process. A given physical router may be a part of one or more OSPF processes. For example, a router connected to more than one area, receiving routing from a border gateway protocol (BGP) process connected to another AS acts as both an area border router and an autonomous system router. Each router has a unique ID, written in decimal format (A.B.C.D). You do not have to associate the router ID with a valid IP address.
PAGE 609
Area Border Router (ABR) Within an AS, an area border router (ABR) connects one or more areas to the backbone. The ABR keeps a copy of the link-state database for every area it connects to, so it may keep multiple copies of the link state database. An ABR takes information it has learned on one of its attached areas and can summarize it before sending it out on other areas it is connected to. An ABR can connect to many areas in an AS, and is considered a member of each area it connects to.
PAGE 610
• • Type 9: Link Local LSA (OSPFv2), Intra-Area-Prefix LSA (OSPFv3) — For OSPFv2, this is a link-local "opaque" LSA as defined by RFC2370. For OSPFv3, this LSA carries the IPv6 prefixes of the router and network links. Type 11 - Grace LSA (OSPFv3) — For OSPFv3 only, this LSA is a link-local “opaque” LSA sent by a restarting OSPFv3 router during a graceful restart. For all LSA types, there are 20-byte LSA headers. One of the fields of the LSA header is the link-state ID.
PAGE 611
Figure 102. Priority and Cost Examples OSPF Implementation The Dell Networking OS supports up to 10,000 OSPF routes for OSPFv2. Within the 10,000 routes, you can designate up to 8,000 routes as external and up to 2,000 as inter/intra area routes. Multiple OSPF processes (OSPF MP) are supported on OSPFv2 only; up to 32 simultaneous processes are supported. On OSPFv3, the system supports only one process at a time for all platforms.
PAGE 612
Multi-Process OSPFv2 (IPv4 only) Multi-process OSPF is supported only on OSPFv2 with IPv4 on the switch. Up to 32 OSPFv2 processes are supported. Multi-process OSPF allows multiple OSPFv2 processes on a single router. Multiple OSPFv2 processes allow for isolating routing domains, supporting multiple route policies and priorities in different domains, and creating smaller domains for easier management. Each OSPFv2 process has a unique process ID and must have an associated router ID.
PAGE 613
To confirm that you enabled RFC-2328–compliant OSPF flooding, use the show ip ospf command. Dell#show ip ospf Routing Process ospf 1 with ID 2.2.2.
PAGE 614
OSPF features and functions are assigned to each router using the CONFIG-INTERFACE commands for each interface. NOTE: By default, OSPF is disabled. Configuration Task List for OSPFv2 (OSPF for IPv4) You can perform the following tasks to configure Open Shortest Path First version 2 (OSPF for IPv4) on the switch. Two of the tasks are mandatory; others are optional.
PAGE 615
If you try to enter an OSPF process ID, or if you try to enable more OSPF processes than available Layer 3 interfaces, prior to assigning an IP address to an interface and setting the no shutdown command, the following message displays: Dell(conf)#router ospf 1 % Error: No router ID available. Assigning a Router ID In CONFIGURATION ROUTER OSPF mode, assign the router ID. The router ID is not required to be the router’s IP address.
PAGE 616
Assigning an OSPFv2 Area After you enable OSPFv2, assign the interface to an OSPF area. Set up OSPF areas and enable OSPFv2 on an interface with the network command. You must have at least one AS area: Area 0. This is the backbone area. If your OSPF network contains more than one area, configure a backbone area (Area ID 0.0.0.0). Any area besides Area 0 can have any number ID assigned to it. The OSPFv2 process evaluates the network commands in the order they are configured.
PAGE 617
Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Hello due in 00:00:04 Neighbor Count is 0, Adjacent neighbor count is 0 TengigabitEthernet 12/21 is up, line protocol is up Internet Address 10.2.3.1/24, Area 0.0.0.0 Process ID 1, Router ID 11.1.2.1, Network Type BROADCAST, Cost: 1 Transmit Delay is 1 sec, State BDR, Priority 1 Designated Router (ID) 13.1.1.1, Interface address 10.2.3.2 Backup Designated Router (ID) 11.1.2.1, Interface address 10.2.3.
PAGE 618
Area ID is the number or IP address assigned when creating the area. To view which LSAs are transmitted, use the show ip ospf database process-id database-summary command in EXEC Privilege mode. Dell#show ip ospf 34 database database-summary OSPF Router with ID (10.1.2.100) (Process ID 34) Area 2.2.2.2 3.3.3.3 Dell# ID Router Network S-Net S-ASBR Type-7 Subtotal 1 0 0 0 0 1 1 0 0 0 0 1 To view information on areas, use the show ip ospf process-id command in EXEC Privilege mode.
PAGE 619
Transmit Delay is 1 sec, State DOWN, Priority 1 Designated Router (ID) 10.1.2.100, Interface address 0.0.0.0 Backup Designated Router (ID) 0.0.0.0, Interface address 0.0.0.0 Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Hello due in 13:39:46 Neighbor Count is 0, Adjacent neighbor count is 0 TengigabitEthernet 0/1 is up, line protocol is down Internet Address 10.1.3.100/24, Area 2.2.2.2 Process ID 34, Router ID 10.1.2.
PAGE 620
Convergence Level 0 Min LSA origination 5 secs, Min LSA arrival 1 secs Number of area in this router is 0, normal 0 stub 0 nssa 0 Dell# Changing OSPFv2 Parameters on Interfaces You can modify the OSPF configuration on switch interfaces. Some interface parameter values must be consistent across all interfaces to avoid routing errors. For example, set the same time interval for the hello packets on all routers in the OSPF network to prevent misconfiguration of OSPF neighbors.
PAGE 621
To view interface configurations, use the show config command in CONFIGURATION INTERFACE mode. To view interface status in the OSPF process, use the show ip ospf interface command in EXEC mode. The bold lines in the example show the change on the interface. The change is reflected in the OSPF configuration. Dell(conf-if)#ip ospf cost 45 Dell(conf-if)#show config ! interface TengigabitEthernet 0/0 ip address 10.1.2.100 255.255.255.
PAGE 622
Applying Prefix Lists To apply prefix lists to incoming or outgoing OSPF routes, use the following commands. • Apply a configured prefix list to incoming OSPF routes. • CONFIG-ROUTEROSPF-id mode distribute-list prefix-list-name in [interface] Assign a configured prefix list to outgoing OSPF routes. CONFIG-ROUTEROSPF-id distribute-list prefix-list-name out [connected | isis | rip | static] Redistributing Routes You can add routes from other routing instances or protocols to the OSPF process.
PAGE 623
• show routes To help troubleshoot OSPFv2, use the following commands. • View the summary of all OSPF process IDs enables on the router. • EXEC Privilege mode show running-config ospf View the summary information of the IP routes. • EXEC Privilege mode show ip route summary View the summary information for the OSPF database. • EXEC Privilege mode show ip ospf database View the configuration of OSPF neighbors connected to the local router.
PAGE 624
Basic OSPFv2 Router Topology The following illustration is a sample basic OSPFv2 topology. Figure 103. Basic Topology and CLI Commands for OSPFv2 OSPF Area 0 — Te 1/1 and 1/2 router ospf 11111 network 10.0.11.0/24 area 0 network 10.0.12.0/24 area 0 network 192.168.100.0/24 area 0 ! interface TengigabitEthernet 1/1 ip address 10.1.11.1/24 no shutdown ! interface TengigabitEthernet 1/2 ip address 10.2.12.2/24 no shutdown ! interface Loopback 10 ip address 192.168.100.
PAGE 625
OSPF Area 0 — Te 2/1 and 2/2 router ospf 22222 network 192.168.100.0/24 area 0 network 10.2.21.0/24 area 0 network 10.2.22.0/24 area 0 ! interface Loopback 20 ip address 192.168.100.20/24 no shutdown ! interface TengigabitEthernet 2/1 ip address 10.2.21.2/24 no shutdown ! interface TengigabitEthernet 2/2 ip address 10.2.22.2/24 no shutdown OSPFv3 NSSA NSSA (Not-So-Stubby-Area) is a stub area that does not support Type-5 LSAs, but supports Type-7 LSAs to forward external links.
PAGE 626
Enable OSPFv3 for IPv6 by specifying an OSPF process ID and an area in INTERFACE mode. If you have not created an OSPFv3 process, it is created automatically. All IPv6 addresses configured on the interface are included in the specified OSPF process. NOTE: IPv6 and OSPFv3 do not support Multi-Process OSPF. You can only enable a single OSPFv3 process. To create multiple OSPF processes you need to have multiple VRFs on a switch.
PAGE 627
• area-id: the area ID for this interface. Assigning OSPFv3 Process ID and Router ID Globally To assign, disable, or reset OSPFv3 globally, use the following commands. • Enable the OSPFv3 process globally and enter OSPFv3 mode. CONFIGURATION mode ipv6 router ospf {process ID} • The range is from 0 to 65535. Assign the router ID for this OSPFv3 process. CONF-IPV6-ROUTER-OSPF mode router-id {number} • number: the IPv4 address. The format is A.B.C.D.
PAGE 628
ipv6 ospf interface-cost • • interface-cost:The range is from 1 to 65535. Default cost is based on the bandwidth. Specify how the OSPF interface cost is calculated based on the reference bandwidth method. The cost of an interface is calculated as Reference Bandwidth/Interface speed. ROUTER OSPFv3 auto-cost [reference-bandwidth ref-bw] To return to the default bandwidth or to assign cost based on the interface type, use the no auto-cost [referencebandwidth ref-bw] command.
PAGE 629
• • • • • bgp | connected | static: enter one of the keywords to redistribute those routes. metric metric-value: The range is from 0 to 4294967295. metric-type metric-type: enter 1 for OSPFv3 external route type 1 OR 2 for OSPFv3 external route type 2. route-map map-name: enter a name of a configured route map. tag tag-value: The range is from 0 to 4294967295. Configuring a Default Route To generate a default external route into the OSPFv3 routing domain, configure the following parameters.
PAGE 630
OSPFv3 Authentication Using IPsec: Configuration Notes OSPFv3 authentication using IPsec is implemented according to the specifications in RFC 4552. • To use IPsec, configure an authentication (using AH) or encryption (using ESP) security policy on an interface or in an OSPFv3 area. Each security policy consists of a security policy index (SPI) and the key used to validate OSPFv3 packets. After IPsec is configured for OSPFv3, IPsec operation is invisible to the user.
PAGE 631
• • • • • key: specifies the text string used in authentication. All neighboring OSPFv3 routers must share key to exchange information. For MD5 authentication, the key must be 32 hex digits (non-encrypted) or 64 hex digits (encrypted). For SHA-1 authentication, the key must be 40 hex digits (non-encrypted) or 80 hex digits (encrypted). Remove an IPsec authentication policy from an interface.
PAGE 632
The security policy index (SPI) value must be unique to one IPSec security policy (authentication or encryption) on the router. Configure the same authentication policy (the same SPI and key) on each interface in an OPSFv3 link. If you have enabled IPSec encryption in an OSPFv3 area using the area encryption command, you cannot use the area authentication command in the area at the same time. The configuration of IPSec authentication on an interface-level takes precedence over an area-level configuration.
PAGE 633
• • • key-authentication-type: (optional) specifies if the authentication key is encrypted. The valid values are 0 or 7. Remove an IPsec encryption policy from an OSPFv3 area. no area area-id encryption ipsec spi number Display the configuration of IPsec encryption policies on the router. show crypto ipsec policy Displaying OSPFv3 IPsec Security Policies To display the configuration of IPsec authentication and encryption policies, use the following commands.
PAGE 634
The following example shows the show crypto ipsec sa ipv6 command.
PAGE 635
• • • debug ipv6 ospf events and/or packets show ipv6 neighbors show ipv6 routes Viewing Summary Information To get general route, configuration, links status, and debug information, use the following commands. • View the summary information of the IPv6 routes. • EXEC Privilege mode show ipv6 route summary View the summary information for the OSPFv3 database. • EXEC Privilege mode show ipv6 ospf database View the configuration of OSPFv3 neighbors.
PAGE 636
MIB Object OID Description ospfv3NbrEntry 1.3.6.1.2.1.191.1.9.1 Contains a table describing all neighbors in the locality of the OSPFv3 router. Viewing the OSPFv3 MIB • To view the OSPFv3 MIB generated by the system, use the following command. snmpwalk -c ospf1 -v2c 10.16.133.129 1.3.6.1.2.1.191.1.1 SNMPv2-SMI::mib-2.191.1.1.1.0 = Gauge32: 336860180 SNMPv2-SMI::mib-2.191.1.1.2.0 = INTEGER: 1 SNMPv2-SMI::mib-2.191.1.1.3.0 = INTEGER: 3 SNMPv2-SMI::mib-2.191.1.1.4.0 = INTEGER: 1 SNMPv2-SMI::mib-2.191.1.
PAGE 637
37 Per-VLAN Spanning Tree Plus (PVST+) Protocol Overview A sample PVST+ topology is shown below. For more information about spanning tree, refer to the Spanning Tree Protocol (STP) chapter. Figure 104. Per-VLAN Spanning Tree The Dell Networking OS supports three other versions of spanning tree, as shown in the following table. Table 67. Spanning Tree Versions Supported Dell Networking Term IEEE Specification Spanning Tree Protocol (STP) 802 .1d Rapid Spanning Tree Protocol (RSTP) 802 .
PAGE 638
Implementation Information • • The Dell Networking OS implementation of PVST+ is based on IEEE Standard 802.1w. The Dell Networking OS implementation of PVST+ uses IEEE 802.1s costs as the default costs (as shown in the following table). Other implementations use IEEE 802.1w costs as the default costs. If you are using Dell Networking systems in a multivendor network, verify that the costs are values you intended. Configure Per-VLAN Spanning Tree Plus Configuring PVST+ is a four-step process. 1. 2. 3. 4.
PAGE 639
Influencing PVST+ Root Selection As shown in the previous PVST+ illustration, all VLANs use the same forwarding topology because R2 is elected the root, and all TengigabitEthernet ports have the same cost. The following per-VLAN spanning tree illustration changes the bridge priority of each bridge so that a different forwarding topology is generated for each VLAN. This behavior demonstrates how you can use PVST+ to achieve load balancing. Figure 105.
PAGE 640
Number of topology changes 5, last change occurred 00:34:37 ago on Te 1/32 Port 375 (TengigabitEthernet 1/22) is designated Forwarding Port path cost 20000, Port priority 128, Port Identifier 128.375 Designated root has priority 4096, address 0001.e80d.b6:d6 Designated bridge has priority 4096, address 0001.e80d.b6:d6 Designated port id is 128.
PAGE 641
Table 68. Default Values for Port Cost Port Cost Default Value 100-Mb/s Ethernet interfaces 200000 1-Gigabit Ethernet interfaces 20000 10-Gigabit Ethernet interfaces 2000 Port Channel with 100 Mb/s Ethernet interfaces 180000 Port Channel with 1-Gigabit Ethernet interfaces 18000 Port Channel with 10-Gigabit Ethernet interfaces 1800 NOTE: The Dell Networking OS implementation of PVST+ uses IEEE 802.1s costs as the default costs. Other implementations use IEEE 802.1w costs as the default costs.
PAGE 642
• You can clear the Error Disabled state with any of the following methods: • • • • Perform a shutdown command on the interface. Disable the shutdown-on-violation command on the interface (the no spanning-tree stp-id portfast [bpduguard | [shutdown-on-violation]] command). Disable spanning tree on the interface (the no spanning-tree command in INTERFACE mode). Disabling global spanning tree (the no spanning-tree command in CONFIGURATION mode).
PAGE 643
Bridge ID Priority 32773 (priority 32768 sys-id-ext 5), Address 0001.e832.73f7 We are the root of Vlan 5 Configured hello time 2, max age 20, forward delay 15 PVST+ Sample Configurations The following examples provide the running configurations for the topology shown in the previous illustration.
PAGE 644
no disable vlan 200 bridge-priority 4096 Example of PVST+ Configuration (R3) interface TengigabitEthernet 3/12 no ip address switchport no shutdown ! interface TengigabitEthernet 3/22 no ip address switchport no shutdown ! interface Vlan 100 no ip address tagged TengigabitEthernet 3/12,22 no shutdown ! interface Vlan 200 no ip address tagged TengigabitEthernet 3/12,22 no shutdown ! interface Vlan 300 no ip address tagged TengigabitEthernet 3/12,22 no shutdown ! protocol spanning-tree pvst no disable vlan 30
PAGE 645
38 PIM Sparse-Mode (PIM-SM) Protocol-independent multicast sparse-mode (PIM-SM) is a multicast protocol that forwards multicast traffic to a subnet only after a request using a PIM Join message. This behavior is the opposite of PIM-Dense mode, which forwards multicast traffic to all subnets until a request to stop.
PAGE 646
which the message was received is added to the outgoing interface list associated with the (*,G) entry, and the message is not (and does not need to be) forwarded towards the RP. Refuse Multicast Traffic A host requesting to leave a multicast group sends an IGMP Leave message to the last-hop DR. If the host is the only remaining receiver for that group on the subnet, the last-hop DR is responsible for sending a PIM Prune message up the RPT to prune its branch to the RP. 1.
PAGE 647
• Creating Multicast Boundaries and Domains Enable PIM-SM You must enable PIM-SM on each participating interface. 1. Enable multicast routing on the system. CONFIGURATION mode ip multicast-routing 2. Enable PIM-Sparse mode. INTERFACE mode ip pim sparse-mode To display which interfaces are enabled with PIM-SM, use the show ip pim interface command from EXEC Privilege mode. show ip pim interface Address Interface Ver/ Mode 1.1.1.1 Te 1/0 v2/S 2.1.1.1 Te 11/0 v2/S 5.1.1.1 Vl 10 v2/S 6.1.1.
PAGE 648
To configure a global expiry time or to configure the expiry time for a particular (S,G) entry, use the following command. Enable global expiry timer for S, G entries. CONFIGURATION mode ip pim sparse-mode sg-expiry-timer seconds The range is from 211 to 86,400 seconds. The default is 210. Dell(conf)#ip pim sparse-mode sg-expiry-timer 1800 To display the expiry time configuration, use the show running-configuration pim command from EXEC Privilege mode.
PAGE 649
with the greatest priority value is the DR. If the priority value is the same for two routers, then the router with the greatest IP address is the DR. By default, the DR priority value is 192, so the IP address determines the DR. • Assign a DR priority value. • INTERFACE mode ip pim dr-priority priority-value Change the interval at which a router sends hello messages. • INTERFACE mode ip pim query-interval seconds Display the current value of these parameter.
PAGE 650
Candidate BSR address: 7.7.7.
PAGE 651
39 PIM Source-Specific Mode (PIM-SSM) PIM source-specific mode (PIM-SSM) is a multicast protocol that forwards multicast traffic from a single source to a subnet. In the other versions of protocol independent multicast (PIM), a receiver subscribes to a group only. The receiver receives traffic not just from the source in which it is interested but from all sources sending to that group.
PAGE 652
Enabling PIM-SSM To enable PIM-SSM, follow these steps. 1. Create an ACL that uses permit rules to specify what range of addresses should use SSM. CONFIGURATION mode ip access-list standard name 2. Enter the ip pim ssm-range command and specify the ACL you created. CONFIGURATION mode ip pim ssm-range acl-name To display address ranges in the PIM-SSM range, use the show ip pim ssm-range command from EXEC Privilege mode. R1(conf)#do show run pim ! ip pim rp-address 10.11.12.2 group-address 224.0.0.
PAGE 653
R1(conf)#ip igmp ssm-map map 10.11.5.2 R1(conf)#do show ip igmp groups Total Number of Groups: 2 IGMP Connected Group Membership Group Address Interface Mode Uptime 239.0.0.2 Vlan 300 IGMPv2-Compat 00:00:07 Member Ports: Te 1/1 239.0.0.1 Vlan 400 INCLUDE 00:00:10 Never 10.11.4.2 R1(conf)#do show ip igmp ssm-map IGMP Connected Group Membership Group Address Interface Mode Uptime 239.0.0.2 Vlan 300 IGMPv2-Compat 00:00:36 Member Ports: Te 1/1 R1(conf)#do show ip igmp ssm-map 239.0.0.
PAGE 654
3. If you configure a secondary VLT peer as an E-BSR and in case of ICL flap or failover, the VLT lag will be down resulting a BSM timeout in the PIM domain and a new BSR will be elected. Hence, it is recommended to configure the primary VLT peer as E-BSR. To enable BSR election for IPv4 or IPv6, perform the following steps: 1. Enter the following IPv4 or IPv6 command to make a PIM router a BSR candidate: CONFIGURATION ip pim bsr-candidate ipv6 pim bsr-candidate 2.
PAGE 655
NOTE: You can create the ACL list of multicast prefix using the ip access-list standard command.
PAGE 656
40 Policy-based Routing (PBR) Policy-based Routing (PBR) allows a switch to make routing decisions based on policies applied to an interface.
PAGE 657
To enable a PBR, you create a redirect list. Redirect lists are defined by rules, or routing policies.
PAGE 658
Configuration Task List for Policy-based Routing This section explains how to configure PBR on the system. PBR Exceptions (Permit) To create an exception to a redirect list, use thepermit command. Exceptions are used when a forwarding decision should be based on the routing table rather than a routing policy. The Dell EMC Networking OS assigns the first available sequence number to a rule configured without a sequence number and inserts the rule into the PBR CAM region next to the existing entries.
PAGE 659
In addition to supporting multiple redirect-lists in a redirect-group, multiple redirect-groups are supported on a single interface. Dell Networking OS has the capability to support multiple groups on an interface for backup purposes. Show Redirect List Configuration To view the configuration redirect list configuration, use the following commands. 1. View the redirect list configuration and the associated interfaces. EXEC mode show ip redirect-list redirect-list-name 2.
PAGE 660
Create the Redirect-List GOLD EDGE_ROUTER(conf-if-Te-2/23/1)#ip redirect-list GOLD EDGE_ROUTER(conf-redirect-list)#description Route GOLD traffic to ISP_GOLD. EDGE_ROUTER(conf-redirect-list)#direct 10.99.99.254 ip 192.168.1.0/24 any EDGE_ROUTER(conf-redirect-list)#redirect 10.99.99.254 ip 192.168.2.0/24 any EDGE_ROUTER(conf-redirect-list)# seq 15 permit ip any any EDGE_ROUTER(conf-redirect-list)#show config ! ip redirect-list GOLD description Route GOLD traffic to ISP_GOLD. seq 5 redirect 10.99.99.
PAGE 661
View Redirect-List GOLD EDGE_ROUTER#show ip redirect-list IP redirect-list GOLD: Defined as: seq 5 redirect 10.99.99.254 ip 192.168.1.0/24 any, Next-hop reachable (via Te 3/23/1), ARP resolved seq 10 redirect 10.99.99.254 ip 192.168.2.
PAGE 662
hop reachable (via Vl 20) Applied interfaces: Te 2/28 Dell# Configuration Tasks for Creating a PBR list using Explicit Track Objects for Tunnel Interfaces Creating steps for Tunnel Interfaces: Dell#configure terminal Dell(conf)#interface tunnel 1 Dell(conf-if-tu-1)#tunnel destination 40.1.1.2 Dell(conf-if-tu-1)#tunnel source 40.1.1.1 Dell(conf-if-tu-1)#tunnel mode ipip Dell(conf-if-tu-1)#tunnel keepalive 60.1.1.2 Dell(conf-if-tu-1)#ip address 60.1.1.
PAGE 663
Verify the Applied Redirect Rules: Dell#show ip redirect-list explicit_tunnel IP redirect-list explicit_tunnel: Defined as: seq 5 redirect tunnel 1 track 1 tcp 155.55.2.0/24 222.22.2.0/24, Track 1 [up], Next-hop reachable (via Te 1/32) seq 10 redirect tunnel 1 track 1 tcp any any, Track 1 [up], Next-hop reachable (via Te 1/32) seq 15 redirect tunnel 1 track 1 udp 155.55.0.0/16 host 144.144.144.144, Track 1 [up], Nexthop reachable (via Te 1/32) seq 20 redirect tunnel 2 track 2 tcp 155.55.2.0/24 222.22.2.
PAGE 664
41 Port Extenders (PEs) IEEE 802.1BR The IEEE 802.1BR protocol allows a controlling bridge to use IEEE LAN technologies to discover and manage port extenders. The following illustration shows how a controlling bridge connects through an automatically established port channel (auto-LAG) to an uplink port on one or more port extenders. Figure 107. Controlling Bridge with Port Extenders 1. Controlling Bridge (C9010) 3. 10GbE uplink ports on PEs 5. PE stack 2. Cascade ports on controlling bridge 4.
PAGE 665
802.1BR Term Definition Port extender (PE) A bridge port extender that is not physically part of a controlling bridge, but is controlled by the controlling bridge. Upstream port A port on a bridge port extender that connects to a cascade port. In the case of the connection between two bridge port extenders, the upstream port is the port furthest from the controlling bridge.
PAGE 666
PORT-EXTENDER CONFIGURATION mode Dell(conf-pe-0)# cascade interface interface-type slot/port-range • • interface interface-type specifies a C9010 10-Gigabit Ethernet interface. The only supported value is TenGigabitEthernet slot/port-range. slot/port-range specifies a C9010 10GbE port, including slot number and either a single port number, a port range, or a combination of both for auto-LAG configuration. • The range of slot numbers is from 0 to 11.
PAGE 667
NOTE: In the User-Configured Cascade Ports field, A (active) indicates that a C9010 port is up (no shutdown) and configured as a cascade port; I (inactive) indicates that a port is down and configured as a cascade port. Dell# show interface port-channel brief Codes: L - LACP Port-channel O - OpenFlow Controller Port-channel A - Auto Port-channel A LAG 258 Mode N/A Status up Uptime 14:45:26 Ports Te 0/1,2 (up) Port Extender Limit You can connect a maximum of 80 PE units to the C9010 control bridge.
PAGE 668
provisioned for PE 10; port 1/12 is provisioned for PE 20. As a result, only PE 10 comes online. PE 20 remains offline and its configured cascade port is placed in an error state.
PAGE 669
PE-id: Not Assigned PE MAC: 00:01:02:03:22:02 Interface Errors: TenGigabitEthernet 1/8 - Error State • You may connect a PE to a parent C9010 using both uplink ports but provision the PE with only the cascade port attached to one of the uplink ports. In this case, the auto-LAG is created with only the provisioned cascade port when the PE comes online. In the following example, PE 10 is provisioned to connect only to cascade port 1/12.
PAGE 670
• pe-id is a port-extender ID number from 0 to 255. Dell# connect pe 254 Login: peadmin Password: calvin Displaying PE Status To verify the operational status of a port extender attached to a C9010, enter any of the show commands in this section. In the command output, online indicates that a port extender is up; offline indicates that a port extender is down.
PAGE 671
ECP ECP ECP ECP ECP Tx: 10 Rx Ack: 10 Dropped: 0 Rx: 6 Tx Ack: 6 Dell#show pe 10 system brief Stack MAC : a0:68:00:3f:92:bc -- Stack Info -Unit UnitType Status ReqTyp CurTyp Version Ports -----------------------------------------------------------------------------------0 Management online C1048P C1048P 9-9(0-5) 52 1 Member not present 2 Standby not present C1048P 3 Member not present C1048P 4 Member not present 5 Member not present 6 Member not present 7 Member not present -- Power Supplies -Unit Bay S
PAGE 672
1. Enter Configuration mode. CONFIGURATION mode Dell(conf)# mac-address-table station-move threshold number interval seconds • number is the threshold value. The range is from 5 to 50. After you enter a threshold value, you can specify a time interval in seconds. The range is from 1 to 60 seconds. Dell(conf)# mac-address-table station-move threshold 5 interval 30 NOTE: Dell Networking OS recommends that you use the command because xSTP protocols are not supported on PEs. 2.
PAGE 673
• At kernel, the following validations are done: • • Any control PDU (LACP or LLDP or ARP or DHCP etc) received at CB will be first checked for the source MAC address against matching any one of its PEX interface address. • In this scenario the source MAC could be the system MAC and in this case, the receiving PE interface would be brought down to cut the loop.
PAGE 674
This loop will be broken based on the data traffic or control PDUs received at the PE. In the event of data traffic at the PE and continuous station moves between the PE and LM interface, the PE interface will be brought down. In case there is no data traffic on the LAN, control PDUs received at the PE will be used to break the loop.
PAGE 675
• rpmA: or rpmB: specifies the flash partition (A: or B:) on the controlling bridge where the OS version to use for the PE upgrade is stored. Dell# Dell#upgrade system-image pe all rpmB: !!!!!!!!!!!!!!!!!!! Sep 7 13:03:32: %PE255-UNIT1-M:CP %DOWNLOAD-6-UPGRADE: Upgrade reques Bridge. !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! PE (255) Image upgraded successfully. 2. After the upgrade is successful, reload the PE or PE stack.
PAGE 676
RPM 1 RPM 1 Backup FPGA IAP 2.0 3.2 PE RELEASE IMAGE INFORMATION : --------------------------------------------------------------------Platform Version Size ReleaseTime C-Series:C1048P 9.9(0.0) 27132051 Sep 4 2015 09:59:54 PE BOOT IMAGE INFORMATION : --------------------------------------------------------------------Type Version Target Checksum boot flash 3.3.1.
PAGE 677
pe-version-compat-support enable 2. Schedule a reboot or upgrade of the PEs with the state SVC but has a mismatched version with CB using the following command: reset pe schedule at 0:10-12/29/2017 range 1,3,5-10 no-confirm This command resets all the PEs with pe-ids in range 5 to 10 and pe-ids 1 and 3 at 0:10 AM on 29th Dec, 2017. 3.
PAGE 678
• • • STP Edge port support on PE interfaces VLAN stacking VLT Dual Homing Dual homing provides support to manage and control the PEs from both the primary and the secondary chassis in a VLT setup. The C9010 switch supports dual homing using port extenders. You can also stack the port extenders in a dual homing setup. The following figure shows PE dual homing, where the port extenders are dual-homed to a pair of C9010 switches. Figure 108.
PAGE 679
2. There is a CB connected to PE and a standalone CB. You can physically connect the CBs and then configure them as VLT peers. Then physically connect the uplink ports of the PE to each of the VLT peers. The system starts functioning as a dual homing setup. Refer to Standalone System. 3. There are two standalone CBs not connected to PEs. You can physically connect the CBs and then configure them as VLT peers. Then physically connect the uplink ports of the PE to the VLT peers.
PAGE 680
NOTE: After saving the configurations to the startup-config, reload the system with unit ID 1. This is mandatory and proceed with further configurations after reloading the system. 6. Add VLTi for the election to happen between the systems. 7. System A and system B become VLT peers after the election of primary and secondary VLT units. 8. The PE connected to primary is online and PE to secondary remains offline. 9.
PAGE 681
Cascade LAG: Po 258, Local Status: Up, Remote Status: Up PE Configuration: Local Status: Present, Remote Status: Present -----------------------------------------------------------------------Stack-id Status Reason Type UnitMac No.
PAGE 682
3. Remove the disconnected interface (Te 0/1) from the configuration mode of PE 1 in System A. The configuration would be already available in System A and needs to be removed. PE CONFIGURATION (BATCH mode) no cascade interface interface slot/port Dell(conf-b-pe-1)# no cascade interface TenGigabitEthernet 0/1 4. Configure the cascade interface of the System B through the batch mode of System A and commit the configuration.
PAGE 683
3. Configure the PE interface through batch mode of System A. PE CONFIGURATION (BATCH mode) Dell#cascade interface TenGigabitEthernet 0/0 4. Configure the cascade interface of the System B through the batch mode of System A and commit the configuration.
PAGE 684
Dell#show running-config pe ! feature extended-bridge ! pe provision 200 cascade interface TenGigabitEthernet 0/22-23 stack-unit 2 type C1048P Dell#show pe brief -- Port Extenders Information ----------------------------------------------------------PE-id Status Stack-size Type System-MAC ---------------------------------------------------------200 online 1 C1048P f8:b1:56:00:02:8a Dell#show pe 200 Codes: A - Active, I - Inactive SVC - Software Version Compatible Reason: CTM - Card Type Mismatch, CAM - CAM
PAGE 685
Proceed Boot Flash image for all cards [yes/no]: yes !!!!!!Sep 7 19:20:23: %RPM0-P:CP %DOWNLOAD-6-UPGRADE: PE 0 manual upgrade result - upgrade success. !!!!! Bootflash image upgrade for all cards completed successfully. Warning: Kindly save the system configuration before reloading. Dell# 2. Use the upgrade system-image all command to upgrade the image in both the CB and the PE. Dell#upgrade system-image all ftp: B: Address or name of remote host []: 10.16.127.141 Source file name []: $w/Releases/E9.9.
PAGE 686
PE-ID assigned: 200 Status: offline System Mac: f8:b1:56:00:02:8a PE Up Time: 00:00:00 PE Discovery Status: Provisioned PE User Configured Cascade Ports: Te 0/22(A),Te 0/23(A) Cascade LAG: Po 458(Up) -----------------------------------------------------------------------Stack-id Status Reason Type UnitMac No.
PAGE 687
changed to 1 (Current temperature 36C).
PAGE 688
Image upgraded to all linecards C9010-2# 2. Change the boot parameters to boot from the upgraded partition. Save and reload the secondary VLT peer. C9010-2#configure terminal C9010-2(conf)#boot system rpm0 primary system: B: C9010-2(conf)#boot system rpm1 primary system: B: C9010-2(conf)#end C9010-2#reload System configuration has been modified. Save? [yes/no]: yes ! Synchronizing data to peer RPM !!! Proceed with reload [confirm yes/no]: yes All VLT LAG's gracefully shut down...
PAGE 689
Proceed with reload [confirm yes/no]: yes All VLT LAG's gracefully shut down...!!! Starting to save trace messages...done. syncing disks... done unmounting file systems... unmounting /f10/phonehome (tmpfs)... unmounting /f10/flash (/dev/wd0e)... unmounting /f10/ConfD/db (mfs:295)... unmounting /usr/pkg (/dev/wd0i)... unmounting /boot (/dev/wd0b)... unmounting /usr (tmpfs)... unmounting /force10 (mfs:19)... unmounting /lib (tmpfs)... unmounting /f10 (tmpfs)... unmounting /tmp (tmpfs)...
PAGE 690
• • PVLAN • Station move • Routing and ECMP IPv6 • • NDP and routing • VRF Layer 2 • • MAC Synchronization • PVLAN • Mac Learning Limit • BPDU guard • Loop Detection Multicast • • • • IGMP Snooping • PIM PBR Power Over Ethernet QoS CLIs Supported on Primary VLT Node In a dual homing setup, the following commands work only from the primary VLT peer.
PAGE 691
42 Port Extender (PE) Stacking You can stack up to eight port extenders using the mini-SAS stack ports on the back panel. The C1048P supports stacking only with other C1048P port extenders. The N20xx series devices support stacking only with other N20xx series port extenders. The N30xx series devices support stacking only with other N30xx series port extenders. Stacking is not supported on C9010 switches.
PAGE 692
NOTE: If a stack unit does not boot up at the same time as the other units, it does not participate in the election process. Units that boot up late do not participate in the election process because the master and standby have already been elected. The unit that boots up late (even if they have a higher priority configured) joins as a member. To display the PE stack master, enter the show pe pe—id system brief command. The following example shows output from an established stack.
PAGE 693
3. Configure the cascade ports on the C9010 which are attached to PE stack units. The cascade ports must be operationally up (the no shutdown command) and have a default port configuration with no L2 and L3 configuration. The port interfaces must be the same type. You can configure up to sixteen C9010 ports in the auto-LAG. The generated auto-LAG number is from 258 to 513.
PAGE 694
SVM - Software Version Mismatch, UE - Unknown Error Offline Reason: UNP - Unit Not Present, PVE - Port Validation Error ICE - IPC CP Error, IRE - IPC RP Error ISE - IPC Setup Error, CVE - Card Validation Error PE-ID assigned: 2 Status: online System Mac: a0:68:00:3f:92:bc PE Up Time: 14:06:37 PE Discovery Status: Provisioned PE User Configured Cascade Ports: Te 0/0(A) Cascade LAG: Po 258, Local Status: Up, Remote Status: Up PE Configuration: Local Status: Present, Remote Status: Present --------------------
PAGE 695
Where: • • • pe pe-id is the PE ID number. The range is from 0 to 255. stack-unit unit-id is the stack-unit ID number. The range is from 0 to 7. renumber renumber is the new stack-unit ID. Dell# pe 200 stack-unit 3 renumber 5 Renumbering the stack master triggers a stack reload, as shown in the following message. When the stack comes back online, the master unit remains the management unit. Renumbering management unit will reload the stack.
PAGE 696
The following example shows the redundancy reset-counter pe command. Dell #redundancy reset-counter pe 0 • Display redundancy information. EXEC Privilege mode show redundancy pe pe-id pe-id — Port-extender identifier of the master stack unit. The range is from to 255. The following example shows the show redundancy pe command.
PAGE 697
3 4 5 6 7 Standby Member Member Member Member online C1048P not present not present not present not present C1048P 1-0(0-4149) 52 The following example displays the status of stack-unit 1 after it is removed from the PE stack.
PAGE 698
5 6 7 • online online online - C1048P C1048P C1048P cb:28:00:42:bd:7c 62:74:00:41:54:01 6c:c0:00:43:11:11 52 52 52 Display summary information about the PE stack units attached to the master PE. Enter the PE ID of the master unit.
PAGE 699
Service Tag Expr Svc Code Auto Reboot Burned In MAC No Of MACs : : : : : CL73Z01 274 031 203 69 enabled f8:b1:56:00:02:d1 66 -- Power Supplies -Unit Bay Status Type FanStatus FanSpeed(rpm) ------------------------------------------------------------2 0 up AC NA NA 2 1 up DC NA NA -- Fan Status -Unit Bay TrayStatus Fan0 Speed Fan1 Speed -----------------------------------------------------------2 0 up up 9056 up 9056 Speed in RPM • Display the type of stack topology (ring or daisy chain) with a list of a
PAGE 700
When the uplink port is converted to access port, Dell EMC Networking OS creates a logical peTenGigE interface based on the 10/100/1000BASE-T Ports in the PE. There is a maximum of 4 uplink ports in a PE. The C1048P and N20xx have two standard uplink ports in the front panel, while the N30xx have two standard uplink ports in the front panel and one expansion slot for plug-in module on the back panel. The expansion slot supports 10GBASE-T or SFP+ module and each module has two ports. Figure 115.
PAGE 701
NOTE: When a PE is reloaded, the uplink port come up as uplink by default, even though it has been configured as access ports. After connecting to CB, the system converts the uplink port to access port. Until conversion, some LLDP packets are advertised. Configuring Uplink Ports as Access Ports Under the PE provision configuration, you can configure the uplink ports as access port using the following steps: 1. Enter Port-Extender Configuration mode to provision a PE.
PAGE 702
0 runts, 0 giants, 0 throttles 0 CRC, 0 overrun, 0 discarded Output Statistics: 0 packets, 0 bytes, 0 underruns 0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts 0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts 0 Multicasts, 0 Broadcasts, 0 Unicasts 0 throttles, 0 discarded, 0 collisions, 0 wreddrops Rate info (interval 299 seconds): Input 00.00 Mbits/sec, 0 packets/sec, 0.00% of line-rate Output 00.00 Mbits/sec, 0 packets/sec, 0.
PAGE 703
Using PE Console Commands To debug an error condition in a PE stack, you can connect a console to the console port on the master unit and enter PE console commands. Contact Dell Networking support for assistance. The supported PE console commands are described in the C9000 Series Command-Line Reference Guide.
PAGE 704
43 Port Monitoring Port monitoring (also referred to as mirroring) allows you to monitor ingress and/or egress traffic on specified ports. The mirrored traffic can be sent to a port to which a network analyzer is connected to inspect or troubleshoot the traffic. The Dell Networking OS supports the following mirroring techniques: • • • Port monitoring — Monitors network traffic by forwarding a copy of incoming and outgoing packets from a source port to a destination port on the same network router.
PAGE 705
Figure 116. Port Monitoring Configurations Dell Networking OS Behavior: All monitored frames are tagged if the configured monitoring direction is egress (TX), regardless of whether the monitored port (MD) is a Layer 2 or Layer 3 port. If the MD port is a Layer 2 port, the frames are tagged with the VLAN ID of the VLAN to which the MD belongs. If the MD port is a Layer 3 port, the frames are tagged with VLAN ID 4095.
PAGE 706
Example of Configuring Another Monitoring Session with a Previously Used Destination Port Dell(conf)#mon ses 300 Dell(conf-mon-sess-300)#source tengig 0/17 destination tengig 0/4 direction tx %Unable to create MTP entry for MD tenG 0/17 MG tenG 0/4 in stack-unit 0 port-pipe 0.
PAGE 707
• • tx: to monitor transmitting packets only. both: to monitor both transmitting and receiving packets. flow-based enable — Specify flow-based enable for mirroring on a flow-by-flow basis and also for VLAN as source. destination interface — Enter one of the following keywords and slot/port information. NOTE: • • • • You cannot configure cascade ports as a destination port. For a 10–Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 708
Remote Port Mirroring Local port monitoring allows you to monitor traffic from one or more source ports by directing it to a destination port on the same switch/ router. Remote port mirroring allows you to monitor Layer 2 and Layer 3 ingress and/or egress traffic on multiple source ports on different switches and forward the mirrored traffic to multiple destination ports on different switches.
PAGE 709
Figure 118. Remote Port Mirroring Configuring Remote Port Mirroring Remote port mirroring requires a source session (monitored ports on different source switches), a reserved tagged VLAN for transporting mirrored traffic (configured on source, intermediate, and destination switches), and a destination session (destination ports connected to analyzers on destination switches).
PAGE 710
• There is no restriction on the VLAN IDs used for the reserved remote-mirroring VLAN. Valid VLAN IDs are from 2 to 4094. The default VLAN ID is not supported. In mirrored traffic, packets that have the same destination MAC address as an intermediate or destination switch in the path used by the reserved VLAN to transport the mirrored traffic are dropped by the switch that receives the traffic if the switch has a L3 VLAN configured.
PAGE 711
To display the current configuration of the reserved VLAN, enter the show vlan command.
PAGE 712
• The Dell EMC Networking OS supports ERPM source session only. Encapsulated packets terminate at the destination IP address or at the analyzer. • You can configure up to four ERPM source sessions on switch. • Configure the system MTU to accommodate the increased size of the ERPM mirrored packet. • The maximum number of source ports you can define in a session is 128.
PAGE 713
The port monitoring or mirroring function when applied to VLT devices works as expected except with some restrictions. You can configure RPM or ERPM monitoring between two VLT peers. As VLT devices are seen as a single device in the network, when a fail over occurs, the source or destination port on one of the VLT peers becomes inactive causing the monitoring session to fail. As a result, Dell Networking OS does not allow local Port mirroring based monitoring to be configured between VLT peers.
PAGE 714
Scenario RPM Restriction Recommended Solution Mirroring Orphan Ports across VLT Devices — In this scenario, an orphan port on the primary VLT device is mirrored to another orphan port on the secondary VLT device through the ICL LAG. The port analyzer is connected to the secondary VLT device. No restrictions apply to the RPM session. The following example shows the configuration on the primary VLT device:source orphan port destination remote vlan direction rx/tx/both.
PAGE 715
44 Power over Ethernet (PoE) The PoE feature supports electrical power and transmission of data on Ethernet cabling. A single cable can provide both a data connection and electrical power to the attached devices such as wireless access points or IP cameras. The PoE feature is supported on a C1048P, N2024P, N2048P , N3024P, or N3048P port-extender (PE); PoE is not supported on the C9010 switches. PoE, as described by IEEE 802.3af, specifies that a maximum of 15.
PAGE 716
Configuring PoE or PoE+ Configuring PoE or PoE+ is a two-step process: 1. Connect the IEEE 802.3af/802.3at-compliant powered device directly to a port. 2. Enable PoE or PoE+ on the port extender. Enabling PoE or PoE+ on a Port By default, PoE or PoE+ are disabled. Configuration tasks for PoE include: • • Enabling PoE and managing the inline power supplied to the port extender ports using the power inline mode command. To manage inline power in a port extender, use Configure Class or Static mode.
PAGE 717
NOTE: Static ports have a higher weight than Class mode ports, so all static ports always stay on top of all class ports, regardless of the other three parameters. 2. Power inline priority configuration 3. Link layer discovery protocol-media endpoint discovery (LLDP-MED) priority the power device (PD) sends in the Extended Power-viamedium dependent interface (MDI) type, length, value (TLV) or the priority the PD sends in the IEEE 802.3at power-via-MDI TLV 4.
PAGE 718
Configuring Power Management on the PE — Class and Static Mode By default, PoE or PoE+ are disabled. To manage the inline power supplied to the port extender ports, use the power inline mode command in Configuration mode. The mode configuration applies to all the ports on the port extender. To manage the inline power in a port extender, you can configure Class or Static mode. This command has the following parameters.
PAGE 719
Allocate PoE Power to Powered Devices to a Connected PE Interface To enable inline power and configure the maximum power allocation and priority for the powered device connected to a port extender interface, use the power inline {[max_milliwatts] | priority {critical | high | low}} command in Interface mode. By default, power inline is disabled. Port Prioritization To specify the priority on a particular interface on the port extender, use the power inline priority command.
PAGE 720
Dell(conf-if-pegi-255/0/1)#power inline ? <440-30000> Max milliwatts (default = 30000) priority Configure poe priority Dell(conf-if-pegi-0/0/1)#power inline 30000 Example of Setting the Priority to Critical The following example sets the priority on interface peGigE 255/0/1 to critical.
PAGE 721
Figure 120.
PAGE 722
Advertising the Extended Power through MDI The power device sends the following information in the LLDP-MED extended power-via-MDI TLV. 1. Power Requirement: Dell Networking OS uses it for power allocation 2. Power Priority — Critical, High, or Low: Dell Networking OS uses it for power priority calculation. 3. External Power Source: Dell Networking OS does not use this information. IEEE 802.3at power-via-mdi TLV To configure the system or an interface to advertise IEEE 802.
PAGE 723
advertise dot3-tlv power-via-mdi Example of Advertising in LLDP Configuration Mode The following example configures all the interfaces to advertise extended power though dot3–TLVs in configuration mode. Dell(conf-lldp)#advertise dot3-tlv power-via-mdi Example of Advertising in LLDP Interface Configuration Mode The following example configures interface peGigE 0/0/1 to advertise extended power though dot3–TLVs.
PAGE 724
Creating VLANs for an Office VoIP Deployment The phone in the previous figure requires one tagged VLAN for VoIP service and one untagged VLAN for PC data, as shown in the following example. You can configure voice signaling on the voice VLAN but some implementations may need an extra tagged VLAN for this traffic.
PAGE 725
Configuring QoS for an Office VoIP Deployment There are several ways you can use quality of service (QoS) to map ingress phone and PC traffic to give them each a different quality of service. Honoring the Incoming DSCP Value If you know that traffic originating from the phone is tagged with the DSCP value of 46 (EF), you can make the associated queue a strictpriority queue, as shown in the following example.
PAGE 726
Classifying VoIP Traffic and Applying QoS Policies You can avoid congestion and give precedence to voice and signaling traffic by classifying traffic based on the subnet and using strict priority and bandwidth weights on egress, as outlined in the following steps. The following figure depicts the topology and configuration for a C9000 system. Figure 122. PoE VoIP Traffic To classify VoIP traffic and apply QoS policies for an office VoIP deployment, use the following commands: 1.
PAGE 727
Example of the sh run acl command. Dell#sh run acl ! ip access-list extended pc-subnet seq 5 permit ip 201.1.1.0/24 any ! ip access-list extended phone-signalling seq 5 permit ip 192.1.1.0/24 host 192.1.1.1 ! ip access-list extended phone-subnet seq 5 permit ip 192.1.1.
PAGE 728
Upgrading the PoE Controller To upgrade the PoE controller firmware on a port extender, use the following command. You can upgrade the PoE controller firmware using the firmware packaged with the Dell Networking OS. After the upgrade is successful, the port extender reloads automatically. NOTE: You cannot upgrade the PoE controller when any other upgrade is in progress. Upgrading the PoE controller may take a few minutes to complete. Also, the CLI is blocked until the upgrade is complete. 1.
PAGE 729
power inline restore pe pe-id stack-unit unit-number • • pe pe-id — Specify the port extender ID. The range is from 0 to 255. stack-unit unit-number — Specify the stack unit number of the port extender. The range is from 0 to 7. Example of Restoring Power Delivery on the Port Extender The following example disable power delivery on the port extender.
PAGE 730
PoE or PoE+ Power Budget Limit Model Name Maximum PSU Output Ability (1 PSU) Maximum PSUs System Power Output Ability Consumed (2 PSUs) Redundancy Power Consumed Threshold Max In-line Power Available default. Supports up to two 1100 W PSUs. The following table shows the maximum number of ports that you can configure for PoE and PoE+ based on the number of PSUs available on the C1048P. NOTE: The table assumes maximum of 30 W for PoE+ and 15.4 W for PoE. Table 74.
PAGE 731
• interface interface — Enter the interface keyword and specify the PE Gigabit Ethernet interface using the keyword peGigE or peTenGigE. Specify a pe-id/unit/port for the interface.
PAGE 732
• • pe pe-id — Enter the keyword pe and the port extender ID. The range is from 0 to 255. stack-unit unit-number — Enter the keyword stack-unit and the stack unit number. The range is from 0 to 7.
PAGE 733
45 Private VLANs (PVLAN) Private VLANs (PVLANs) extend Dell Networking OS security suite by providing Layer 2 isolation between ports within the same virtual local area network (VLAN). A PVLAN partitions a traditional VLAN into subdomains identified by a primary and secondary VLAN pair. Private VLANs block all traffic to isolated ports except traffic from promiscuous ports. Traffic received from an isolated port is forwarded only to promiscuous ports or trunk ports.
PAGE 734
PVLAN port types include: • Host port — in the context of a private VLAN, is a port in a secondary VLAN. The port must first be assigned that role in INTERFACE mode. • • • Host port that belongs to a community VLAN is allowed to communicate with other ports in the same community VLAN and with promiscuous ports & Trunk Port in Same PVLAN • Host port can be part of either community VLAN or isolated VLAN. The bhavior of host port will change with respect to its presence in community and isolated VLAN.
PAGE 735
Configuration Task List The following sections contain the procedures that configure a private VLAN. • • • • Creating PVLAN Ports Creating a Primary VLAN Creating a Community VLAN Creating an Isolated VLAN Creating PVLAN ports PVLAN ports are those that will be assigned to the PVLAN. 1. Access INTERFACE mode for the port that you want to assign to a PVLAN. CONFIGURATION mode interface interface 2. Enable the port. INTERFACE mode no shutdown 3. Set the port in Layer 2 mode. INTERFACE mode switchport 4.
PAGE 736
interface vlan vlan-id 2. Enable the VLAN. INTERFACE VLAN mode no shutdown 3. Set the PVLAN mode of the selected VLAN to primary. INTERFACE VLAN mode private-vlan mode primary 4. Map secondary VLANs to the selected primary VLAN. INTERFACE VLAN mode private-vlan mapping secondary-vlan vlan-list The list of secondary VLANs can be: • • • Specified in comma-delimited (VLAN-ID,VLAN-ID) or hyphenated-range format (VLAN-ID-VLAN-ID). Specified with this command even before they have been created.
PAGE 737
Creating an Isolated VLAN An isolated VLAN is a secondary VLAN of a primary VLAN. An isolated VLAN port can only talk with the promiscuous ports in that primary VLAN. 1. Access INTERFACE VLAN mode for the VLAN that you want to make an isolated VLAN. CONFIGURATION mode interface vlan vlan-id 2. Enable the VLAN. INTERFACE VLAN mode no shutdown 3. Set the PVLAN mode of the selected VLAN to isolated. INTERFACE VLAN mode private-vlan mode isolated 4. Add one or more host ports to the VLAN.
PAGE 738
Private VLAN Configuration Example The following example shows a private VLAN topology. Figure 123. Sample Private VLAN Topology The following configuration is based on the example diagram: • • • • • Te 0/0 and Te 23 are configured as promiscuous ports, assigned to the primary VLAN, VLAN 4000. Te 0/25 is configured as a PVLAN trunk port, also assigned to the primary VLAN 4000. Te 0/24 and Te 0/47 are configured as host ports and assigned to the isolated VLAN, VLAN 4003.
PAGE 739
• • The S50V ports would have the same intra-switch communication characteristics as described for the C300. For transmission between switches, tagged packets originating from host PVLAN ports in one secondary VLAN and destined for host PVLAN ports in the other switch travel through the promiscuous ports in the local VLAN 4000 and then through the trunk ports (0/25 in each switch). Inspecting the Private VLAN Configuration The standard methods of inspecting configurations also apply in PVLANs.
PAGE 740
The following example shows the VLAN status. Dell#show vlan Codes: * - Default VLAN, G - GVRP VLANs, P - Primary, C - Community, I - Isolated Q: U - Untagged, T - Tagged x - Dot1x untagged, X - Dot1x tagged G - GVRP tagged, M - Vlan-stack NUM * 1 100 P 200 I 201 Status Inactive Inactive Inactive Inactive Description Q Ports primary VLAN in PVLAN T Te 0/19-20 isolated VLAN in VLAN 200 T Te 0/21 The following example shows viewing a private VLAN configuration.
PAGE 741
46 Quality of Service (QoS) This chapter describes how to use and configure Quality of Service (QoS) features on the switch. Differentiated service is accomplished by classifying and queuing traffic, and assigning priorities to those queues. Figure 124.
PAGE 742
Implementation Information The Dell Networking QoS implementation complies with IEEE 802.1p User Priority Bits for QoS Indication.
PAGE 743
Honoring dot1p Priorities on Ingress Traffic By default, the system does not honor dot1p priorities on ingress traffic. You can configure this feature on physical interfaces and port-channels, but you cannot configure it on individual interfaces in a port channel. You can configure service-class dynamic dot1p from CONFIGURATION mode, which applies the configuration to all interfaces. A CONFIGURATION mode service-class dynamic dot1p entry supersedes any INTERFACE entries.
PAGE 744
rate shape Dell#config Dell(conf)#interface tengigabitethernet 1/2 Dell(conf-if)#rate shape 500 50 Dell(conf-if)#end Dell# Policy-Based QoS Configurations Policy-based QoS configurations consist of the components shown in the following example. Figure 125. Constructing Policy-Based QoS Configurations Classify Traffic Class maps differentiate traffic so that you can apply separate quality of service policies to different types of traffic.
PAGE 745
NOTE: IPv6 and IP-any class maps cannot match on ACLs or VLANs. Use step 1 or step 2 to start creating a Layer 3 class map. 1. Create a match-any class map. CONFIGURATION mode class-map match-any class-map-name 2. Create a match-all class map. CONFIGURATION mode class-map match-all class-map-name 3. Specify your match criteria. CLASS MAP mode match {ip | ipv6 | ip-any} After you create a class-map, you are placed in CLASS MAP mode. Match-any class maps allow up to five ACLs.
PAGE 746
class-map match-all 3. Specify your match criteria. CLASS MAP mode match mac After you create a class-map, you are placed in CLASS MAP mode. Match-any class maps allow up to five access-lists. Match-all class-maps allow only one. You can match against only one VLAN ID. 4. Link the class-map to a queue. POLICY MAP mode service-queue Applying Layer 2 Match Criteria on a Layer 3 Interface To process Layer 3 packets that contain a dot1p (IEEE 802.
PAGE 747
5. Configure the DSCP value to be set on matched packets. QOS-POLICY-IN mode Dell(conf-qos-policy-in)#set ip-dscp 5 6. Create an input policy map. CONFIGURATION mode Dell(conf)#policy-map-input pp_policmap 7. Create a service queue to associate the class map and QoS policy map.
PAGE 748
ip access-list extended AF1-FB2 seq 5 permit ip host 23.64.0.3 any seq 10 deny ip any any ! ip access-list extended AF2 seq 5 permit ip host 23.64.0.5 any seq 10 deny ip any any Create a QoS Policy There are two types of QoS policies — input and output. Input QoS policies regulate Layer 3 and Layer 2 ingress traffic. The regulation mechanisms for input QoS policies are rate policing and setting priority values. • • Layer 3 — QoS input policies allow you to rate police and set a DSCP or dot1p value.
PAGE 749
4 (100 b). Dell(conf-qos-policy-in)#show config ! qos-policy-input my-input-qos-policy set ip-dscp 34 Dell(conf-qos-policy-in)#end Dell# Setting a dot1p Value for Egress Packets To set a dot1p value for egress packets, use the following command. • Set a dot1p value for egress packets. QOS-POLICY-IN mode set mac-dot1p Creating an Output QoS Policy To create an output QoS policy, use the following commands. 1. Create an output QoS policy. CONFIGURATION mode qos-policy-output 2.
PAGE 750
Allocating Bandwidth to Queue The switch schedules packets for egress based on Deficit Round Robin (DRR). This strategy offers a guaranteed data rate. Allocate bandwidth to queues only in terms of percentage in 4-queue and 8-queue systems. The following table shows the default bandwidth percentage for each queue. Table 78. Default Bandwidth Weights Queue Default Bandwidth Percentage for 4– Queue System Default Bandwidth Percentage for 8– Queue System 0 6.67% 1% 1 13.33% 2% 2 26.67% 3% 3 53.
PAGE 751
Applying a Class-Map or Input QoS Policy to a Queue To apply a class-map or input QoS policy to a queue, use the following command. • Assign an input QoS policy to a queue. POLICY-MAP-IN mode service-queue Applying an Input QoS Policy to an Input Policy Map To apply an input QoS policy to an input policy map, use the following command. • Apply an input QoS policy to an input policy map.
PAGE 752
Packet dot1p on Ingress Packet Queue ID 7 7 The dot1p value is also honored for frames on the default VLAN. For more information, refer to Priority-Tagged Frames on the Default VLAN. • Enable the trust dot1p feature. POLICY-MAP-IN mode trust dot1p Mapping dot1p Values to Service Queues All traffic is by default mapped to the same queue, Queue 0. If you honor dot1p on ingress, you can create service classes based the queueing strategy in Honoring dot1p Values on Ingress Packets.
PAGE 753
Applying an Output QoS Policy to a Queue To apply an output QoS policy to a queue, use the following command. • Apply an output QoS policy to queues. INTERFACE mode service-queue Specifying an Aggregate QoS Policy To specify an aggregate QoS policy, use the following command. • Specify an aggregate QoS policy. POLICY-MAP-OUT mode policy-aggregate Applying an Output Policy Map to an Interface To apply an output policy map to an interface, use the following command.
PAGE 754
3. Apply the map profile to the interface. CONFIG-INTERFACE mode qos dscp-color-policy color-map-name Example: Create a DSCP Color Map The following example creates a DSCP color map profile, color-awareness policy, and applies it to interface te 0/11.
PAGE 755
Display detailed information about a color policy for a specific interface Dell# show qos dscp-color-policy detail te 0/10 Interface TenGigabitEthernet 0/10 Dscp-color-map mapONE yellow 4,7 red 20,30 Enabling QoS Rate Adjustment By default, while rate limiting, policing, and shaping, the system does not include the Preamble, SFD, or the IFG fields. These fields are overhead; only the fields from MAC destination address to the CRC are used for forwarding and are included in these rate metering calculations.
PAGE 756
Traffic is a mixture of various kinds of packets. The rate at which some types of packets arrive might be greater than others. In this case, the space on the buffer and traffic manager (BTM) (ingress or egress) can be consumed by only one or a few types of traffic, leaving no space for other types. You can apply a WRED profile to a policy-map so that specified traffic can be prevented from consuming too much of the BTM resources. WRED uses a profile to specify minimum and maximum threshold values.
PAGE 757
threshold Applying a WRED Profile to Traffic After you create a WRED profile, you must specify on which traffic the system applies the profile. The system assigns a color-coded drop precedence — red, yellow, or green — to each packet based on the fourth bit of the 6-bit DSCP field in the packet header before queuing it. • • • If the fourth DSCP bit is 0, packet is marked as green. If the fourth DSCP bit is 1, the packet is marked as yellow (except for DSCP 63, which is marked as red).
PAGE 758
3 4 5 6 7 0 0 0 0 0 DELL#show qos statistics wred-profile peGigE 0/1/1 Interface peGigE 0/1/1 Drop-statistic Dropped Pkts Green 0 Yellow 0 Out of Profile 0 Displaying egress-queue Statistics To display the number of transmitted and dropped packets on the egress queues of a WRED-configured interface, use the following command. • Display the number of packets and number of bytes on the egress-queue profile.
PAGE 759
• • • match ip dscp match ip precedence match ip vlan By default, all packets are marked for green handling if the rate-police and trust-diffserv commands are not used in an ingress policy map. All packets marked for red handling or “violate” are dropped. In the class map, in addition to color-marking matching packets for yellow handling, you can also configure a DSCP value for matching packets.
PAGE 760
class-map match-any class_dscp_50 match ip access-group dscp_50_non_ecn set-color yellow match ip access-group dscp_50 policy-map-input pmap_dscp_40_50 service-queue 2 class-map class_dscp_40 service-queue 3 class-map class_dscp_50 The second example shows how to achieve the desired configuration by specifying ECN match criteria to classify ECN-capable packets: ip access-list standard dscp_50_ecn seq 5 permit any dscp 50 ecn 1 seq 10 permit any dscp 50 ecn 2 seq 15 permit any dscp 50 ecn 3 ip access-list st
PAGE 761
The user-configurable weight in WRED and ECN provides better control in how the switch responds to congestion before a queue overflows and packets are dropped or delayed. Using a configurable weight for WRED and ECN allows you to customize network performance and throughput. Setting Average Queue Size using a Weight You can configure the weight factor that determines the average queue size for WRED and ECN packet handling by using the wred weight command.
PAGE 762
Queue Configuration Service-Pool Configuration WRED Threshold Relationship Expected Functionality Q threshold = Q-T Service-pool threshold = SP-T Enabled Disabled Disabled N/A N/A Enabled N/A Q-T < SP-T SP-T < Q-T Queue-based WRED; No ECN marking Service-pool-based WRED; No ECN marking Enabled Enabled Disabled N/A N/A Enabled N/A Q-T < SP-T Queue-based ECN marking above queue threshold. ECN marking up to shared buffer limits of the service-pool and then packets are tail dropped.
PAGE 763
Dell(conf)#service-class wred ecn 0, 3-5, 7 backplane Pre-Calculating Available QoS CAM Space Pre-calculating available QoS CAM space allows you to measure the number of CAM entries a policy-map consumes. This feature allows you to avoid applying a policy-map on an interface that requires more CAM entries than are available and receive a CAM full error message (shown in the following example). The partial policy-map configuration might cause unintentional system behavior.
PAGE 764
• • fpIngPgBuffSnapshotTable: Retrieves BST statistics from the ingress port for the shared and headroom cells used in a priority group. The snapshot of the ingress shared cells and the ingress headroom cells used for each priority group are displayed in this table when PFC is enabled. This table is indexed by stack-unit index, port number and priority-group number.
PAGE 765
47 Routing Information Protocol (RIP) The Routing Information Protocol (RIP) tracks distances or hop counts to nearby routers when establishing network connections and is based on a distance-vector algorithm. RIP protocol standards are listed in the Standards Compliance chapter. Topics: • • • Protocol Overview Implementation Information Configuration Information Protocol Overview RIP is the oldest interior gateway protocol. There are two versions of RIP: RIP version 1 (RIPv1) and RIP version 2 (RIPv2).
PAGE 766
Feature Default RIP timers • • • • Auto summarization Enabled ECMP paths supported 16 update timer = 30 seconds invalid timer = 180 seconds holddown timer = 180 seconds flush timer = 240 seconds Configuration Information By default, RIP is disabled on the switch. To configure RIP, you must use commands in two modes: ROUTER RIP and INTERFACE. Commands executed in the ROUTER RIP mode configure RIP globally, while commands executed in the INTERFACE mode configure RIP features on that interface only.
PAGE 767
When the RIP process has learned the RIP routes, use the show ip rip database command in EXEC mode to view those routes. Dell#show ip rip database Total number of routes in RIP database: 978 160.160.0.0/16 [120/1] via 29.10.10.12, 00:00:26, Fa 0/0 160.160.0.0/16 auto-summary 2.0.0.0/8 [120/1] via 29.10.10.12, 00:01:22, Fa 0/0 2.0.0.0/8 auto-summary 4.0.0.0/8 [120/1] via 29.10.10.12, 00:01:22, Fa 0/0 4.0.0.0/8 auto-summary 8.0.0.0/8 [120/1] via 29.10.10.12, 00:00:26, Fa 0/0 8.0.0.0/8 auto-summary 12.0.0.
PAGE 768
Assigning a Prefix List to RIP Routes Another method of controlling RIP (or any routing protocol) routing information is to filter the information through a prefix list. A prefix list is applied to incoming or outgoing routes. Those routes must meet the conditions of the prefix list; if not, the system drops the route. Prefix lists are globally applied on all interfaces running RIP. Configure the prefix list in PREFIX LIST mode prior to assigning it to the RIP process.
PAGE 769
• Set the RIP versions sent out on that interface. INTERFACE mode ip rip send version [1] [2] To see whether the version command is configured, use the show config command in ROUTER RIP mode. To view the routing protocols configuration, use the show ip protocols command in EXEC mode. The following example shows the RIP configuration after the ROUTER RIP mode version command is set to RIPv2.
PAGE 770
Generating a Default Route Traffic is forwarded to the default route when the traffic’s network is not explicitly listed in the routing table. Default routes are not enabled in RIP unless specified. Use the default-information originate command in ROUTER RIP mode to generate a default route into RIP. Default routes received in RIP updates from other routes are advertised if you configure the default-information originate command. • Specify the generation of a default route in RIP.
PAGE 771
Debugging RIP The debug ip rip command enables RIP debugging. When you enable debugging, you can view information on RIP protocol changes or RIP routes. To enable RIP debugging, use the following command. • debug ip rip [interface | database | events | trigger] EXEC privilege mode Enable debugging of RIP. The following example shows the confirmation when you enable the debug function. Dell#debug ip rip RIP protocol debug is ON Dell# To disable RIP, use the no debug ip rip command.
PAGE 772
Core 2 RIP Output The examples in the section show the core 2 RIP output. • • • To display Core 2 RIP database, use the show ip rip database command. To display Core 2 RIP setup, use the show ip route command. To display Core 2 RIP activity, use the show ip protocols command. To view the learned RIP routes on Core 2, use the show ip rip database command.
PAGE 773
TenGigabitEthernet TenGigabitEthernet TenGigabitEthernet TenGigabitEthernet Routing for Networks: 10.300.10.0 10.200.10.0 10.11.20.0 10.11.10.0 2/42 2/41 2/31 2/11 2 2 2 2 2 2 2 2 Routing Information Sources: Gateway Distance Last Update 10.11.20.1 120 00:00:12 Distance: (default is 120) Core2# RIP Configuration on Core3 The following example shows how to configure RIPv2 on a host named Core3. Core3(conf-if-te-3/21)#router rip Core3(conf-router_rip)#version 2 Core3(conf-router_rip)#network 192.168.1.
PAGE 774
N2 - OSPF NSSA external type 2, E1 - OSPF external type 1, E2 - OSPF external type 2, i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, IA - IS-IS inter area, * - candidate default, > - non-active route, + - summary route Gateway of last resort is not set Destination Gateway Dist/Metric ----------- ------- ----------R 10.11.10.0/24 via 10.11.20.2, Te 3/21 C 10.11.20.0/24 Direct, Te 3/21 C 10.11.30.0/24 Direct, Te 3/11 R 10.200.10.0/24 via 10.11.20.2, Te R 10.300.10.0/24 via 10.11.20.2, Te C 192.168.1.
PAGE 775
10.200.10.0 10.300.10.0 10.11.10.0 10.11.20.0 The following example shows viewing the RIP configuration on Core 3. ! interface TengigabitEthernet 3/11 ip address 10.11.30.1/24 no shutdown ! interface TengigabitEthernet 3/21 ip address 10.11.20.1/24 no shutdown ! interface TengigabitEthernet 3/43 ip address 192.168.1.1/24 no shutdown ! interface TengigabitEthernet 3/44 ip address 192.168.2.1/24 no shutdown ! router rip version 2 network 10.11.20.0 network 10.11.30.0 network 192.168.1.0 network 192.168.2.
PAGE 776
48 Remote Monitoring (RMON) Remote monitoring (RMON) is an industry-standard implementation that monitors network traffic by sharing network monitoring information. RMON provides both 32-bit and 64-bit monitoring facility and long-term statistics collection on Dell Networking Ethernet interfaces. RMON operates with the simple network management protocol (SNMP) and monitors all nodes on a local area network (LAN) segment.
PAGE 777
[no] rmon hc-alarm number variable interval {delta | absolute} rising-threshold value eventnumber falling-threshold value event-number [owner string] Configure the alarm using the following optional parameters: • • • • • • • • • • number: alarm number, an integer from 1 to 65,535, the value must be unique in the RMON Alarm Table. variable: the MIB object to monitor — the variable must be in SNMP OID format; for example, 1.3.6.1.2.1.1.3.
PAGE 778
Configuring RMON Collection Statistics To enable RMON MIB statistics collection on an interface, use the RMON collection statistics command in INTERFACE CONFIGURATION mode. • Enable RMON MIB statistics collection. CONFIGURATION INTERFACE (config-if) mode [no] rmon collection statistics {controlEntry integer} [owner ownername] • • • • controlEntry: specifies the RMON group of statistics using a value. integer: a value from 1 to 65,535 that identifies the RMON Statistics Table.
PAGE 779
49 Rapid Spanning Tree Protocol (RSTP) Protocol Overview The Dell Networking OS supports three other versions of spanning tree, as shown in the following table. Table 84. Spanning Tree Versions Supported Dell Networking Term IEEE Specification Spanning Tree Protocol (STP) 802.1d Rapid Spanning Tree Protocol (RSTP) 802.1w Multiple Spanning Tree Protocol (MSTP) 802.1s Per-VLAN Spanning Tree Plus (PVST+) Third Party Configuring Rapid Spanning Tree Configuring RSTP is a two-step process. 1.
PAGE 780
loops caused by non-system issues such as cabling errors or incorrect configurations. RSTP is useful for potential loop detection but to minimize possible topology changes after link or node failure, configure it using the following specifications.
PAGE 781
To verify that RSTP is enabled, use the show config command from PROTOCOL SPANNING TREE RSTP mode. The bold line indicates that RSTP is enabled. Dell(conf-rstp)#show config ! protocol spanning-tree rstp no disable Dell(conf-rstp)# Figure 128. Rapid Spanning Tree Enabled Globally To view the interfaces participating in RSTP, use the show spanning-tree rstp command from EXEC privilege mode. If a physical interface is part of a port channel, only the port channel is listed in the command output.
PAGE 782
The port is not in the Edge port mode Port 379 (TengigabitEthernet 2/3) is designated Forwarding Port path cost 20000, Port priority 128, Port Identifier 128.379 Designated root has priority 32768, address 0001.e801.cbb4 Designated bridge has priority 32768, address 0001.e801.cbb4 Designated port id is 128.
PAGE 783
NOTE: Dell Networking recommends that only experienced network administrators change the Rapid Spanning Tree group parameters. Poorly planned modification of the RSTP parameters can negatively affect network performance. The following table displays the default values for RSTP. Table 85.
PAGE 784
• Change the port cost of an interface. INTERFACE mode spanning-tree rstp cost cost The range is from 0 to 65535. • The default is listed in the previous table. Change the port priority of an interface. INTERFACE mode spanning-tree rstp priority priority-value The range is from 0 to 15. The default is 128. To view the current values for interface parameters, use the show spanning-tree rstp command from EXEC privilege mode.
PAGE 785
• • Disable spanning tree on the interface (the no spanning-tree command in INTERFACE mode). Disable global spanning tree (the no spanning-tree command in CONFIGURATION mode). To enable EdgePort on an interface, use the following command. • Enable EdgePort on an interface.
PAGE 786
50 Security This chapter describes several ways to provide access security to the Dell Networking system. For details about all the commands described in this chapter, refer to the Security chapter in the Dell Networking OS Command Reference Guide.
PAGE 787
modify the permissions specific to that command and/or command option. For more information, see Modifying Command Permissions for Roles . NOTE: When you enter a user role, you have already been authenticated and authorized. You do not need to enter an enable password because you will be automatically placed in EXEC Priv mode. For greater security, the ability to view event, audit, and security system log is associated with user roles. For information about these topics, see Audit and Security Logs.
PAGE 788
login authentication test authorization exec test To enable role-based only AAA authorization: Dell(conf)#aaa authorization role-only System-Defined RBAC User Roles By default, the Dell Networking OS provides 4 system defined user roles. You can create up to 8 additional user roles. NOTE: You cannot delete any system defined roles. The system defined user roles are as follows: • • • • Network Operator (netoperator) - This user role has no privilege to modify any configuration on the switch.
PAGE 789
1. Create a new user role CONFIGURATION mode userrole name [inherit existing-role-name] 2. Verify that the new user role has inherited the security administrator permissions. Dell(conf)#do show userroles EXEC Privilege mode 3. After you create a user role, configure permissions for the new user role. See Modifying Command Permissions for Roles.
PAGE 790
Example: Allow Security Administrator to Configure Spanning Tree The following example allows the security administrator (secadmin) to configure the spanning tree protocol. Note command is protocol spanning-tree. Dell(conf)#role configure addrole secadmin protocol spanning-tree Example: Allow Security Administrator to Access Interface Mode The following example allows the security administrator (secadmin) to access Interface mode.
PAGE 791
The following example resets only the secadmin role to its original setting. Dell(conf)#no role configure addrole secadmin protocol Example: Reset System-Defined Roles and Roles that Inherit Permissions In the following example the command protocol permissions are reset to their original setting or one or more of the system-defined roles and any roles that inherited permissions from them.
PAGE 792
Configure AAA Authorization for Roles Authorization services determine if the user has permission to use a command in the CLI. Users with only privilege levels can use commands in privilege-or-role mode (the default) provided their privilege level is the same or greater than the privilege level of those commands. Users with defined roles can use commands provided their role is permitted to use those commands. Role inheritance is also used to determine authorization.
PAGE 793
accounting commands role netadmin line vty 6 login authentication ucraaa authorization exec ucraaa accounting commands role netadmin line vty 7 login authentication ucraaa authorization exec ucraaa accounting commands role netadmin line vty 8 login authentication ucraaa authorization exec ucraaa accounting commands role netadmin line vty 9 login authentication ucraaa authorization exec ucraaa accounting commands role netadmin ! ucraaa ucraaa ucraaa ucraaa ucraaa Configuring TACACS+ and RADIUS VSA Attr
PAGE 794
Configuring AAA Accounting for Roles To configure AAA accounting for roles, use the aaa accounting command in CONFIGURATION mode. aaa accounting {system | exec | commands {level | role role-name}} {name | default} {startstop | wait-start | stop-only} {tacacs+} Example of Configuring AAA Accounting for Roles The following example shows you how to configure AAA accounting to monitor commands executed by the users who have a secadmin user role.
PAGE 795
netoperator netadmin secadmin sysadmin MAC testadmin Exec Exec Config Interface Line Router IP Routemap Protocol MAC Exec Config Exec Config Interface Line Router IP Routemap Protocol netadmin Exec Config Interface Line Router IP Routemap Protocol MAC Displaying Role Permissions Assigned to a Command To display permissions assigned to a command, use the show role command in EXEC Privilege mode. The output displays the user role and or permission level.
PAGE 796
Configuration Task List for AAA Accounting The following sections present the AAA accounting configuration tasks.
PAGE 797
In the following sample configuration, AAA accounting is set to track all usage of EXEC commands and commands on privilege level 15. Dell(conf)#aaa accounting exec default start-stop tacacs+ Dell(conf)#aaa accounting command 15 default start-stop tacacs+ Configuring AAA Accounting for Terminal Lines To enable AAA accounting with a named method list for a specific terminal line (where com15 and execAcct are the method list names), use the following commands. • Configure AAA accounting for terminal lines.
PAGE 798
In the following sample configuration, AAA accounting is set to track all usage of EXEC commands and commands on privilege level 15. Dell(conf)# aaa accounting dot1x default start-stop radius Dell(conf)# aaa accounting exec default stop-only radius Sample dot1x accounting records The following lists the sample EAP and MAB accounting records EAP START accounting record: Fri May 10 12:20:43 2019 NAS-IP-Address = 10.16.133.
PAGE 799
MAB STOP record: Fri May 10 23:30:42 2019 User-Name = "001122334455" Called-Station-Id = "00-11-33-44-77-88" Calling-Station-Id = "00-11-22-33-44-55" NAS-IP-Address = 10.16.133.
PAGE 800
RADIUS Attribute code RADIUS Attribute Description 40 Acct-Status-Type STOP 44 Acct-Session-Id CLI Session-Id - To match start and stop session requests. 46 Acct-Session Time Time the user has received the service. 49 Acct-Terminate-Cause Reason for session termination. 61 NAS-Port-Type ASYNC - for Console session. VIRTUAL - for telnet/SSH session. Table 88.
PAGE 801
RADIUS Attribute code RADIUS Attribute Description 95 NAS-IPv6–Address IPv6 address of the NAS. Session Identification Attributes 1 User-Name User name/ Supplicant MAC Address (for MAB). 5 NAS-Port Port on which session is terminated. 6 Service-Type Framed (2) for EAP /Call check (10) for MAB. 8 Framed-IP-Address IPv4 address of supplicant. 168 Framed-IPV6-Address IPv6 address of supplicant. 30 Called-Station-Id Switch MAC Address. 31 Calling-Station-Id Supplicant MAC Address.
PAGE 802
dot1x event Accounting type Attributes Supplicant goes off without explicitly sending EAP logoff Stop Stop record attributes with termination cause as Idle Timeout (4). Periodic Reauth of supplicant Stop Stop record attributes with termination cause as Supplicant restart (19). Failure of dot1x authorized port assignment to untagged VLAN Stop Stop record attributes with termination cause as Port error (8).
PAGE 803
The default method-list is applied to all terminal lines. Possible methods are: • • • • • • enable: use the password you defined using the enable secret, enable password, or enable sha256-password command in CONFIGURATION mode. In general, the enable secret command overrules the enable password command. If you configure the enable sha256-password command, it overrules both the enable secret and enable password commands. line: use the password you defined using the password command in LINE mode.
PAGE 804
To use local enable authentication on the console, while using remote authentication on VTY lines, run the following commands. The following example shows enabling local authentication for console and remote authentication for the VTY lines.
PAGE 805
AAA Authorization The system enables AAA new-model by default. You can set authorization to be either local or remote. Different combinations of authentication and authorization yield different results. By default, the system sets both to local. Privilege Levels Overview Limiting access to the system is one method of protecting the system and your network. However, at times, you might need to allow others access to the router and you can limit that access to a subset of commands.
PAGE 806
• • • encryption-type: Enter 0 for plain text or 7 for encrypted text. password: Enter a string. privilege level The range is from 0 to 15. To view usernames, use the show users command in EXEC Privilege mode. Configuring the Enable Password Command To configure the Dell Networking OS, use the enable command to enter EXEC Privilege level 15. After entering the command, the system requests that you enter a password.
PAGE 807
• If you assign only the first keyword to the privilege level, all commands beginning with that keyword are also assigned to the privilege level. If you enter the entire command, the software assigns the privilege level to that command only. To assign commands and passwords to a custom privilege level, use the following commands. You must be in privilege level 15. 1. Assign a user name and password.
PAGE 808
username admin password 0 admin username john password 0 john privilege 8 ! The following example shows the Telnet session for user john. The show privilege command output confirms that john is in privilege level 8. In EXEC Privilege mode, john can access only the commands listed. In CONFIGURATION mode, john can access only the snmpserver commands. apollo% telnet 172.31.1.53 Trying 172.31.1.53... Connected to 172.31.1.53. Escape character is '^]'.
PAGE 809
EXEC Privilege mode disable level-number • level-number: The level-number you wish to set. If you enter disable without a level-number, your security level is 1. Resetting a Password To reset a password on the switch, follow the procedure in Recovering from a Forgotten Password on the switch. RADIUS Remote authentication dial-in user service (RADIUS) is a distributed client/server protocol.
PAGE 810
RADIUS can specify an ACL for the user if both of the following are true: • • If an ACL is absent. If there is a very long delay for an entry, or a denied entry because of an ACL, and a message is logged. NOTE: The ACL name must be a string. Only standard ACLs in authorization (both RADIUS and TACACS) are supported. Authorization is denied in cases using Extended ACLs.
PAGE 811
Applying the Method List to Terminal Lines To enable RADIUS AAA login authentication for a method list, apply it to a terminal line. To configure a terminal line for RADIUS authentication and authorization, use the following commands. • Enter LINE mode. • CONFIGURATION mode line {aux 0 | console 0 | vty number [end-number]} Enable AAA login authentication for the specified RADIUS method list.
PAGE 812
• Configure a key for all RADIUS communications between the system and RADIUS server hosts. CONFIGURATION mode radius-server key [encryption-type] key • • encryption-type: enter 7 to encrypt the password. Enter 0 to keep the password as plain text. • key: enter a string. The key can be up to 42 characters long. You cannot use spaces in the key. Configure the number of times the system retransmits RADIUS requests.
PAGE 813
Support for Change of Authorization and Disconnect Messages packets The Network Access Server (NAS) uses RADIUS to authenticate AAA or dot1x user-access to the switch. The RADIUS service does not support unsolicited messages sent from the RADIUS server to the NAS. However, there are many instances in which it is desirable for changes to be made to session characteristics, without requiring the NAS to initiate the exchange.
PAGE 814
Table 94. Session Identification Attributes Attribute code Attribute Description 31 Calling-Station-Id (MAC Address) The link address from which session is connected. Table 95.
PAGE 815
Radius Attribute code Radius Attribute Description Mandatory 4 NAS-IP-Address IPv4 address of the NAS. No 95 NAS-IPv6–Address IPv6 address of the NAS. No Port on which session is terminated Yes t=26(vendor-specific);l=length;vendor-identificationattribute;Length=value; Data=”cmd=bounce-host-port” Yes Description Mandatory Session Identification Attributes 5 NAS-Port Authorization Attributes 26 Vendor-Specific Table 99.
PAGE 816
Radius Attribute code Radius Attribute Description Mandatory 5 NAS-Port Port on which session is terminated No t=26(vendor-specific);l=length;vendor-identificationattribute;Length=value; Data=”cmd=disconnect-user” Yes Authorization Attributes 26 Vendor-Specific Error-cause Values It is possible that a Dynamic Authorization Server cannot honor Disconnect Message request or CoA request packets for some reason. The Error-Cause Attribute provides more detail on the cause of the problem.
PAGE 817
• • rejects the CoA-Request containing NAS-IP-Address or NAS-IPV6-Address attribute that does not match the NAS with a CoA-Nak; Error-Cause value is “NAS Identification Mismatch” (403). responds with a CoA-Nak, if it is configured to prohibit honoring of corresponding CoA-Request messages; Error-Cause value is “Administratively Prohibited” (501). NOTE: The Administratively Prohibited Error-Cause is also applicable to following scenarios: • if the dot1x feature is not enabled in the NAS-port.
PAGE 818
NOTE: Unsupported attributes are the ones that are not mentioned in the RFC 5176 but present in the disconnect message that is received by the NAS. rejects the disconnect message containing NAS-IP-Address or NAS-IPV6-Address attribute that does not match NAS with DM-Nak; Error-Cause value is “NAS Identification Mismatch” (403). responds with a DM-Nak, if the NAS is configured to prohibit honoring of disconnect messages; Error-Cause value is “Administratively Prohibited” (501).
PAGE 819
NAS takes the following actions: • • • • • validates the DM request and the session identification attributes. sends a DM-Nak with an error-cause of 402 (missing attribute), if the DM request does not contain the User-Name. sends a DM-Ack, if it is able to successfully disconnect the admin user. sends a DM-Nak with an error-cause value of 506 (resource unavailable), if it is not able to disconnect the admin user.
PAGE 820
NAS re-initiates the user authentication state. Dell(conf#)radius dynamic-auth Dell(conf-dynamic-auth#)coa-reauthenticate NAS takes the following actions whenever re-authentication is triggered: • • • • • • • • • • validates the CoA request and the session identification attributes. sends a CoA-Nak with an error-cause of 402 (missing attribute), if the CoA request does not contain both the calling-station-id as well as the NAS-port attribute. sends a CoA-Ack if the re-authentication of the 802.
PAGE 821
To initiate shutting down of the 802.1x enabled port, the DAC sends a standard CoA request that contains one or more session identification attributes. NAS uses the NAS-port attributes to identify the 802.1x enabled physical port. 1. Enter the following command to configure the dynamic authorization feature: radius dynamic-auth 2. Enter the following command to disable the 802.1x enabled physical port: coa-disable-port NAS administratively shuts down the 802.1x enabled port that is hosting the session.
PAGE 822
Rate-limiting RADIUS packets NAS enables you to allow or reject RADIUS dynamic authorization packets based on the rate-limiting value that you specify. NAS lets you to configure number of RADIUS dynamic authorization packets allowed per minute. The default value is 30 packets per minute. NAS discards the packets, if the number of RADIUS dynamic authorization packets in the current interval cross the configured rate-limit value.
PAGE 823
CONFIGURATION mode line {aux 0 | console 0 | vty number [end-number]} 4. Assign the method-list to the terminal line. LINE mode login authentication {method-list-name | default} To view the configuration, use the show config in LINE mode or the show running-config tacacs+ command in EXEC Privilege mode. If authentication fails using the primary method, the system employs the second method (or third method, if necessary) automatically.
PAGE 824
applies it. If the user is found to be coming from the 10.0.0.0 subnet, the system also immediately closes the Telnet connection. Note, that no matter where the user is coming from, they see the login prompt. When configuring a TACACS+ server host, you can set different communication parameters, such as the key password. Example of Specifying a TACACS+ Server Host Dell# Dell(conf)# Dell(conf)#ip access-list standard deny10 Dell(conf-std-nacl)#permit 10.0.0.
PAGE 825
Protection from TCP Tiny and Overlapping Fragment Attacks Tiny and overlapping fragment attack is a class of attack where configured ACL entries — denying TCP port-specific traffic — is bypassed and traffic is sent to its destination although denied by the ACL. RFC 1858 and 3128 proposes a countermeasure to the problem. This countermeasure is configured into the line cards and enabled by default.
PAGE 826
Using SCP with SSH to Copy a Software Image To use secure copy (SCP) to copy a software image through an SSH connection from one switch to another, use the following commands. 1. On Switch 1, set the SSH port number (port 22 by default). CONFIGURATION mode ip ssh server port number 2. On Switch 1, enable SSH. CONFIGURATION mode ip ssh server enable 3. On Switch 2, invoke SCP. CONFIGURATION mode copy scp: flash: 4.
PAGE 827
Configuring When to Re-generate an SSH Key You can configure the time-based or volume-based rekey threshold for an SSH session. If both threshold types are configured, the session rekeys when either one of the thresholds is reached. To configure the time or volume rekey threshold at which to re-generate the SSH key during an SSH session, use the ip ssh rekey [time rekey-interval] [volume rekey-limit] command. CONFIGURATION mode.
PAGE 828
ip ip no ip ssh server dns enable ssh hostbased-authentication enable ip ssh password-authentication enable ssh server enable Configuring the HMAC Algorithm for the SSH Server To configure the HMAC algorithm for the SSH server, use the ip ssh server mac hmac-algorithm command in CONFIGURATION mode. hmac-algorithm: Enter a space-delimited list of keyed-hash message authentication code (HMAC) algorithms supported by the SSH server.
PAGE 829
Configuring the SSH Server Cipher List To configure the cipher list supported by the SSH server, use the ip ssh server cipher cipher-list command in CONFIGURATION mode. cipher-list-: Enter a space-delimited list of ciphers the SSH server will support. The following ciphers are available. • • • • • • • 3des-cbc aes128-cbc aes192-cbc aes256-cbc aes128-ctr aes192-ctr aes256-ctr The default cipher list is aes256-ctr, aes256-cbc, aes192-ctr, aes192-cbc, aes128-ctr, aes128-cbc, 3des-cbc.
PAGE 830
• • When you enable all the three authentication methods, password authentication is the backup method when the RSA method fails. The files known_hosts and known_hosts2 are generated when a user tries to SSH using version 1 or version 2, respectively. Enabling SSH Authentication by Password Authenticate an SSH client by prompting for a password when attempting to connect to the Dell Networking system. This setup is the simplest method of authentication and uses SSH version 1.
PAGE 831
4. Copy the file shosts and rhosts to the Dell Networking system. 5. Disable password authentication and RSA authentication, if configured CONFIGURATION mode or EXEC Privilege mode no ip ssh password-authentication or no ip ssh rsa-authentication 6. Enable host-based authentication. CONFIGURATION mode ip ssh hostbased-authentication enable 7. Bind shosts and rhosts to host-based authentication.
PAGE 832
Enable host-based authentication on the server (Dell Networking system) and the client (Unix machine). The following message appears if you attempt to log in via SSH and host-based is disabled on the client. In this case, verify that host-based authentication is set to “Yes” in the file ssh_config (root permission is required to edit this file): permission denied (host based). If the IP address in the RSA key does not match the IP address from which you attempt to log in, the following message appears.
PAGE 833
NOTE: For more information, refer to Access Control Lists (ACLs).
PAGE 834
• • When the Network access server (NAS) prompts for the username and password, provide the inputs. If the credentials are valid: • • RADIUS server sends a request to the SMS–OTP daemon to generate an OTP for the user. • A challenge authentication is sent from the RADIUS server as Reply–Message attribute. • If the Reply–Message attribute is not sent from the RADIUS server, the default text is the Response. • 2FA is successful only on providing the correct OTP.
PAGE 835
This module requires NAS for handling the access challenge from the RADIUS server. NAS sends the input OTP in an Access-Request to the RADIUS server, and the user authentication succeeds or fails depending upon the Access-Accept or Access-Reject response received at NAS from the RADIUS server. Configuring the System to Drop Certain ICMP Reply Messages You can configure the Dell Networking OS to drop ICMP reply messages.
PAGE 836
ICMPv6 message types Who are you request (139) Who are you reply (140) Mtrace response (200) Mtrace messages (201) NOTE: The Dell Networking OS does not suppress the following ICMPv6 message types: • • • • • • • • • • • • • • Packet too big (2) Echo request (128) Multicast listener query (130) Multicast listener report (131) Multicast listener done (132) Router solicitation (133) Router advertisement (134) Neighbor solicitation (135) Neighbor advertisement (136) Redirect (137) Router renumbering (138) MLD
PAGE 837
The system continues to display a message stating that startup configuration verification failed. You can disable the startup configuration feature either by disabling startup configuration verification or save the running configuration to the startup configuration and update the hash for the startup configuration. Enabling and Configuring Startup Configuration Hash Verification To enable and configure startup configuration hash verification, follow these steps: 1.
PAGE 838
Enable the user lockout feature. CONFIGURATION password-attributes user-lockout-period minutes Enter the duration in minutes.
PAGE 839
51 Service Provider Bridging VLAN Stacking VLAN stacking, also called Q-in-Q, is defined in IEEE 802.1ad — Provider Bridges, which is an amendment to IEEE 802.1Q — Virtual Bridged Local Area Networks. It enables service providers to use 802.1Q architecture to offer separate VLANs to customers with no coordination between customers, and minimal coordination between customers and the provider. Using only 802.
PAGE 840
Figure 129. VLAN Stacking in a Service Provider Network Important Points to Remember • • • • • Interfaces that are members of the Default VLAN and are configured as VLAN-Stack access or trunk ports do not switch untagged traffic. To switch traffic, add these interfaces to a non-default VLAN-stack-enabled VLAN. Dell Networking cautions against using the same MAC address on different customer VLANs, on the same VLAN-stack VLAN.
PAGE 841
Related Configuration Tasks • • • • Configuring the Protocol Type Value for the Outer VLAN Tag Configuring Options for Trunk Ports Debugging VLAN Stacking VLAN Stacking in Multi-Vendor Networks Creating Access and Trunk Ports To create access and trunk ports, use the following commands. • • Access port — a port on the service provider edge that directly connects to the customer. An access port may belong to only one service provider VLAN.
PAGE 842
3 4 5 6 Inactive Inactive Inactive Active Dell# M Po1(Te 1/14-15) M Te 1/13 Configuring the Protocol Type Value for the Outer VLAN Tag The tag protocol identifier (TPID) field of the S-Tag is user-configurable. To set the S-Tag TPID, use the following command. • Select a value for the S-Tag TPID. CONFIGURATION mode vlan-stack protocol-type The default is 9100. To display the S-Tag TPID for a VLAN, use the show running-config command from EXEC privilege mode.
PAGE 843
G - GVRP tagged, M - Vlan-stack NUM * 1 100 101 103 Status Inactive Inactive Inactive Inactive Description Q Ports U Te 0/1 T Te 0/1 M Te 0/1 Debugging VLAN Stacking To debug VLAN stacking, use the following command. • Debug the internal state and membership of a VLAN and its ports. debug member The port notations are as follows: • • • • • MT — stacked trunk MU — stacked access port T — 802.1Q trunk port U — 802.
PAGE 844
Figure 130.
PAGE 845
Figure 131.
PAGE 846
Figure 132. Single and Double-Tag TPID Mismatch VLAN Stacking Packet Drop Precedence VLAN stacking packet-drop precedence is supported on the switch. The drop eligible indicator (DEI) bit in the S-Tag indicates to a service provider bridge which packets it should prefer to drop when congested. Enabling Drop Eligibility Enable drop eligibility globally before you can honor or mark the DEI value. When you enable drop eligibility, DEI mapping or marking takes place according to the defaults.
PAGE 847
Ingress Egress Access Port Trunk Port DEI Disabled DEI Enabled Retain outer tag CFI Set outer tag CFI to 0. Retain inner tag CFI Retain inner tag CFI Set outer tag CFI to 0 Set outer tag CFI to 0 To enable drop eligibility globally, use the following command. • Make packets eligible for dropping based on their DEI value. CONFIGURATION mode dei enable By default, packets are colored green, and DEI is marked 0 on egress.
PAGE 848
-------------------------------Te 0/1 Green 0 Te 0/1 Yellow 1 Te 1/9 Yellow 0 Te 1/40 Yellow 0 Dynamic Mode CoS for VLAN Stacking One of the ways to ensure quality of service for customer VLAN-tagged frames is to use the 802.1p priority bits in the tag to indicate the level of QoS desired. When an S-Tag is added to incoming customer frames, the 802.1p bits on the S-Tag may be configured statically for each customer or derived from the C-Tag using Dynamic Mode CoS. Dynamic Mode CoS maps the C-Tag 802.
PAGE 849
qos-policy-input 3 layer2 rate-police 40 Likewise, in the following configuration, packets with dot1p priority 0–3 are marked as dot1p 7 in the outer tag and queued to Queue 3. Rate policing is according to qos-policy-input 3. All other packets will have outer dot1p 0 and hence are queued to Queue 1. They are therefore policed according to qos-policy-input 1.
PAGE 850
Figure 134. VLAN Stacking without L2PT You might need to transport control traffic transparently through the intermediate network to the other region. Layer 2 protocol tunneling enables BPDUs to traverse the intermediate network by identifying frames with the Bridge Group Address, rewriting the destination MAC to a user-configured non-reserved address, and forwarding the frames.
PAGE 851
Figure 135. VLAN Stacking with L2PT Implementation Information • • • L2PT is available for STP, RSTP, MSTP, and PVST+ BPDUs. No protocol packets are tunneled when you enable VLAN stacking. L2PT requires the default CAM profile. Enabling Layer 2 Protocol Tunneling To enable Layer 2 protocol tunneling, use the following command. 1. Verify that the system is running the default CAM profile. Use this CAM profile for L2PT. EXEC Privilege mode show cam-profile 2.
PAGE 852
protocol-tunnel stp Specifying a Destination MAC Address for BPDUs By default, the system uses a Dell Networking-unique MAC address for tunneling BPDUs. You can configure another value. To specify a destination MAC address for BPDUs, use the following command. • Overwrite the BPDU with a user-specified destination MAC address when BPDUs are tunneled across the provider network.
PAGE 853
the GVRP Address, 01-80-C2-00-00-21, specified in 802.1Q. Only bridges in the service provider network use this destination MAC address so these bridges treat GARP PDUs originating from the customer network as normal data frames, rather than consuming them. Provider backbone bridging through IEEE 802.
PAGE 854
52 sFlow sFlow is a standard-based sampling technology embedded within switches and routers which is used to monitor network traffic. It is designed to provide traffic monitoring for high-speed networks with many switches and routers.
PAGE 855
• • • • • • • • Only egress sampling is supported. The system exports all sFlow packets to the collector. A small sampling rate can equate to many exported packets. A backoff mechanism is automatically applied to reduce this amount. Some sampled packets may be dropped when the exported packet rate is high and the backoff mechanism is about to or is starting to take effect. The dropEvent counter, in the sFlow packet, is always zero.
PAGE 856
69 sFlow samples dropped due to sub-sampling Linecard 1 Port set 0 H/W sampling rate 8192 Te 1/16: configured rate 8192, actual rate 8192, sub-sampling rate 1 Te 1/17: configured rate 16384, actual rate 16384, sub-sampling rate 2 Displaying Show sFlow on an Interface To view sFlow information on a specific interface, use the following command. • Display sFlow configuration information and statistics on a specific interface.
PAGE 857
The default UDP port is 6343. The default max-datagram-size is 1400. Changing the Polling Intervals The sflow polling-interval command configures the polling interval for an interface in the maximum number of seconds between successive samples of counters sent to the collector. This command changes the global default counter polling (20 seconds) interval. You can configure an interface to use a different polling interval.
PAGE 858
Collector IP addr: 10.10.10.3, Agent IP addr: 10.10.0.
PAGE 859
53 Simple Network Management Protocol (SNMP) The Simple Network Management Protocol (SNMP) is designed to manage devices on IP networks by monitoring device operation, which might require administrator intervention. NOTE: On Dell Networking routers, standard and private SNMP management information bases (MIBs) are supported, including all Get and a limited number of Set operations (such as set vlan and copy cmd).
PAGE 860
MIBs are hierarchically structured and use object identifiers to address managed objects, but managed objects also have a textual name called an object descriptor. Implementation Information The following describes SNMP implementation information. • • • • The Dell Networking OS supports SNMP version 1 as defined by RFC 1155, 1157, and 1212, SNMP version 2c as defined by RFC 1901, and SNMP version 3 as defined by RFC 2571. The system supports up to 16 trap receivers.
PAGE 861
Creating a Community For SNMPv1 and SNMPv2, create a community to enable the community-based security on the switch. The management station generates requests to either retrieve or alter the value of a management object and is called the SNMP manager. A network element that processes SNMP requests is called an SNMP agent. An SNMP community is a group of SNMP agents and managers that are allowed to interact.
PAGE 862
NOTE: To give a user read and write privileges, repeat this step for each privilege type. • Configure an SNMP group (with password or privacy privileges). • CONFIGURATION mode snmp-server group group-name {oid-tree} priv read name write name Configure the user with a secure authorization password and privacy password. • CONFIGURATION mode snmp-server user name group-name {oid-tree} auth md5 auth-password priv des56 priv password Configure an SNMPv3 view.
PAGE 863
The following example shows reading the value of many managed objects at one time. > snmpwalk -v 2c -c public 10.11.198.100 .1.3.6.1.2.1.1 SNMPv2-MIB::sysDescr.0 = STRING: Dell Force10 OS Operating System Version: 2.0 Application Software Version: 9.2(1.0B2) Series: C9000 Copyright (c) 1999-2013 by Dell Inc. All Rights Reserved. Build Time: Sun Jan 12 22:24:47 2014 SNMPv2-MIB::sysObjectID.0 = OID: SNMPv2-SMI::enterprises.6027.1.5.1 DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (133410) 0:22:14.
PAGE 864
CONFIGURATION mode snmpset -v version -c community agent-ip sysLocation.0 s “location-info” You may use up to 55 characters. The default is None. Configuring the CPU Utilization for SNMP Traps When the total CPU utilization exceeds the configured threshold for the specified time, a threshold notification is sent as an SNMP trap. If a low threshold value is not specified, the low threshold value is set to the same value as the high threshold value.
PAGE 865
RP LP LP LP LP LP LP LP LP LP LP LP LP PE 0 1 2 3 4 5 6 7 8 9 10 11 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 85 85 85 85 85 85 85 85 85 85 85 85 85 85 75 75 75 75 75 75 75 75 75 75 75 75 75 75 80 80 80 80 80 80 80 80 80 80 80 80 80 80 70 70 70 70 70 70 70 70 70 70 70 70 70 70 Configuring Threshold Memory Utilization for SNMP Traps When the total memory utilization for a CPU exceeds the configured high/low threshold for a given time, a threshold notification is sent as an SNMP trap.
PAGE 866
LP LP LP LP LP LP LP LP LP LP LP LP PE 0 1 2 3 4 5 6 7 8 9 10 11 92 92 92 92 92 92 92 92 92 92 92 92 85 82 82 82 82 82 82 82 82 82 82 82 82 70 Subscribing to Managed Object Value Updates using SNMP By default, the system displays some unsolicited SNMP messages (traps) upon certain events and conditions. You can also configure the system to send the traps to a management station. Traps cannot be saved on the system.
PAGE 867
• Enable a subset of SNMP traps. snmp-server enable traps NOTE: The envmon option enables all environment traps including those traps that are enabled with the envmon supply, envmon temperature, and envmon fan options. The following traps are available.
PAGE 868
vlt Enable VLT traps. vrrp Enable VRRP state change traps xstp %SPANMGR-5-STP_NEW_ROOT: New Spanning Tree Root, Bridge ID Priority 32768, Address 0001.e801.fc35. %SPANMGR-5-STP_TOPOLOGY_CHANGE: Bridge port TenGigabitEthernet 11/38 transitioned from Forwarding to Blocking state. %SPANMGR-5-MSTP_NEW_ROOT_BRIDGE: Elected root bridge for instance 0. %SPANMGR-5-MSTP_NEW_ROOT_PORT: MSTP root changed to port Te 11/38 for instance 0. My Bridge ID: 40960:0001.e801.fc35 Old Root: 40960:0001.e801.
PAGE 869
SNMP OID %SYSTEM-P:CP %SNMP-4-RMON_HC_RISING_THRESHOLD: RMON high-capacity rising threshold alarm from SNMP OID Enabling an SNMP Agent to Notify Syslog Server Failure You can configure a network device to send an SNMP trap if an audit processing failure occurs due to loss of connectivity with the syslog server. If a connectivity failure occurs on a syslog server that is configured for reliable transmission, an SNMP trap is sent and a message is displayed on the console.
PAGE 870
Copy Configuration Files Using SNMP To do the following, use SNMP from a remote client. • • • copy the running-config file to the startup-config file copy configuration files from the Dell Networking system to a server copy configuration files from a server to the Dell Networking system You can perform all of these tasks using IPv4 or IPv6 addresses. The examples in this section use IPv4 addresses; however, you can substitute IPv6 addresses for the IPv4 addresses in all of the examples.
PAGE 871
MIB Object OID Object Values Description copyDestFileName .1.3.6.1.4.1.6027.3.5.1.1.1.1.7 Path (if the file is not in the default directory) and filename. Specifies the name of destination file. copyServerAddress .1.3.6.1.4.1.6027.3.5.1.1.1.1.8 IP Address of the server. The IP address of the server. • copyUserName .1.3.6.1.4.1.6027.3.5.1.1.1.1.9 Username for the server. Username for the FTP, TFTP, or SCP server. • copyUserPassword .1.3.6.1.4.1.6027.3.5.1.1.1.1.10 Password for the server.
PAGE 872
Copying Configuration Files via SNMP To copy the running-config to the startup-config from the UNIX machine, use the following command. • Copy the running-config to the startup-config from the UNIX machine. snmpset -v 2c -c public force10system-ip-address copySrcFileType.index i 2 copyDestFileType.index i 3 The following examples show the command syntax using MIB object names and the same command using the object OIDs. In both cases, a unique index number follows the object.
PAGE 873
FTOS-COPY-CONFIG-MIB::copyDestFileLocation.110 = INTEGER: ftp(4) FTOS-COPY-CONFIG-MIB::copyServerAddress.110 = IpAddress: 11.11.11.11 FTOS-COPY-CONFIG-MIB::copyUserName.110 = STRING: mylogin FTOS-COPY-CONFIG-MIB::copyUserPassword.110 = STRING: mypass Copying the Startup-Config Files to the Server via TFTP To copy the startup-config to the server via TFTP from the UNIX machine, use the following command. NOTE: Verify that the file exists and its permissions are set to 777.
PAGE 874
MIB Object OID Values Description 4 = file exists 5 = file not found 6 = timeout 7 = unknown copyEntryRowStatus .1.3.6.1.4.1.6027.3.5.1.1.1.1.15 Row status Specifies the state of the copy operation. Uses CreateAndGo when you are performing the copy. The state is set to active when the copy is completed. Obtaining a Value for MIB Objects To obtain a value for any of the MIB objects, use the following command. • Get a copy-config MIB object value. snmpset -v 2c -c public -m ./f10-copy-config.
PAGE 875
Viewing the Reason for Last System Reboot Using SNMP • To view the reason for last system reboot using SNMP, you can use any one of the applicable SNMP commands: The following example shows a sample output of the snmpwalk command to view the last reset reason. [apoosappan@login-maa-06 ~]$ snmpwalk -c public -v 2c 10.16.130.49 1.3.6.1.4.1.6027.3.26.1.4.3.1.7 DELL-NETWORKING-CHASSIS-MIB::dellNetProcessorResetReason.supervisor.1.
PAGE 876
snmpwalk -v 2c -c public -On 10.16.150.97 1.3.6.1.4.1.6027.3.26.1.4.8 .1.3.6.1.4.1.6027.3.26.1.4.8.1.2.1 .1.3.6.1.4.1.6027.3.26.1.4.8.1.2.2 .1.3.6.1.4.1.6027.3.26.1.4.8.1.2.3 .1.3.6.1.4.1.6027.3.26.1.4.8.1.2.4 .1.3.6.1.4.1.6027.3.26.1.4.8.1.3.1 .1.3.6.1.4.1.6027.3.26.1.4.8.1.3.2 .1.3.6.1.4.1.6027.3.26.1.4.8.1.3.3 .1.3.6.1.4.1.6027.3.26.1.4.8.1.3.4 .1.3.6.1.4.1.6027.3.26.1.4.8.1.4.1 .1.3.6.1.4.1.6027.3.26.1.4.8.1.4.2 .1.3.6.1.4.1.6027.3.26.1.4.8.1.4.3 .1.3.6.1.4.1.6027.3.26.1.4.8.1.4.4 .1.3.6.1.4.1.6027.3.
PAGE 877
MIB Object OID Description dellNetFpEgrQDroppedBytesRate 1.3.6.1.4.1.6027.3.27.1.20.1.9 Rate of Bytes dropped per Unicast/ Multicast Egress queue. MIB Support to Display Egress Queue Statistics Dell Networking OS provides MIB objects to display the information of the ECMP group count information. The following table lists the related MIB objects: Table 114. MIB Objects to display ECMP Group Count MIB Object OID Description dellNetInetCidrECMPGrpMax 1.3.6.1.4.1.6027.3.9.1.
PAGE 878
STRING: 4C 76 25 F4 AB 02 SNMPv2-SMI::enterprises.6027.3.9.1.5.1.9.1.1.4.10.1.1.2.32.1.4.127.0.0.1.1.4.127.0.0.1 = "" SNMPv2-SMI::enterprises.6027.3.9.1.5.1.9.1.1.4.20.1.1.0.24.0.0.0.0 = "" SNMPv2-SMI::enterprises.6027.3.9.1.5.1.9.1.1.4.20.1.1.1.32.1.4.20.1.1.1.1.4.20.1.1.1 = HexSTRING: 4C 76 25 F4 AB 02 SNMPv2-SMI::enterprises.6027.3.9.1.5.1.9.1.1.4.20.1.1.2.32.1.4.127.0.0.1.1.4.127.0.0.1 = "" SNMPv2-SMI::enterprises.6027.3.9.1.5.1.9.1.1.4.30.1.1.0.24.0.0.0.0 = "" SNMPv2-SMI::enterprises.6027.3.9.1.5.1.9.
PAGE 879
Gauge32: 0 SNMPv2-SMI::enterprises.6027.3.9.1.5.1.11.1.1.4.10.1.1.2.32.1.4.127.0.0.1.1.4.127.0.0.1 = Gauge32: 0 SNMPv2-SMI::enterprises.6027.3.9.1.5.1.11.1.1.4.20.1.1.0.24.0.0.0.0 = Gauge32: 0 SNMPv2-SMI::enterprises.6027.3.9.1.5.1.11.1.1.4.20.1.1.1.32.1.4.20.1.1.1.1.4.20.1.1.1 = Gauge32: 0 SNMPv2-SMI::enterprises.6027.3.9.1.5.1.11.1.1.4.20.1.1.2.32.1.4.127.0.0.1.1.4.127.0.0.1 = Gauge32: 0 SNMPv2-SMI::enterprises.6027.3.9.1.5.1.11.1.1.4.30.1.1.0.24.0.0.0.0 = Gauge32: 0 SNMPv2-SMI::enterprises.6027.3.9.1.5.
PAGE 880
Viewing the entAliasMappingTable MIB • To view the entAliasMappingTable generated by the system, use the following command. snmpwalk -v 2c -c public -On 10.16.150.97 1.3.6.1.2.1.47.1.3.2.1 .1.3.6.1.2.1.47.1.3.2.1.2.5.0 = OID: .1.3.6.1.2.1.2.2.1.1.2097157 .1.3.6.1.2.1.47.1.3.2.1.2.9.0 = OID: .1.3.6.1.2.1.2.2.1.1.2097669 .1.3.6.1.2.1.47.1.3.2.1.2.13.0 = OID: .1.3.6.1.2.1.2.2.1.1.2098181 .1.3.6.1.2.1.47.1.3.2.1.2.17.0 = OID: .1.3.6.1.2.1.2.2.1.1.2098693 .1.3.6.1.2.1.47.1.3.2.1.2.21.0 = OID: .1.3.6.1.2.1.2.2.
PAGE 881
In the above example: • • • 33997973 is the count of green packet-drops (Green Drops). 329629607 is the count of yellow packet-drops (Yellow Drops). 31997973 is the count of red packet-drops (Out of Profile Drops). MIB Support for LAG Dell Networking provides a method to retrieve the configured LACP information (Actor and Partner).
PAGE 882
MIB Object OID Description from an Aggregator Parser, and either delivering the frame to its MAC Client or discarding the frame. dot3adAggPortListTable 1.2.840.10006.300.43.1.1.2 Contains a list of all the ports associated with each Aggregator. Each LACP channel in a device occupies an entry in the table. dot3adAggPortListEntry 1.2.840.10006.300.43.1.1.2.1 Contains a list of ports associated with a given Aggregator and indexed by the ifIndex of the Aggregator. dot3adAggPortListPorts 1.2.840.10006.
PAGE 883
snmpwalk -v2c -c mycommunity 10.16.150.83 1.0.8802.1.1.2.1.4 iso.0.8802.1.1.2.1.4.1.1.6.0.2113029.2 = INTEGER: 5 iso.0.8802.1.1.2.1.4.1.1.6.0.3161092.6 = INTEGER: 5 iso.0.8802.1.1.2.1.4.1.1.6.0.3161605.2 = INTEGER: 5 iso.0.8802.1.1.2.1.4.1.1.6.0.4209668.6 = INTEGER: 5 iso.0.8802.1.1.2.1.4.1.1.6.0.4210181.2 = INTEGER: 5 iso.0.8802.1.1.2.1.4.1.1.6.0.9437185.2 = INTEGER: 5 iso.0.8802.1.1.2.1.4.1.1.7.0.2113029.2 = STRING: "fortyGigE 1/50" iso.0.8802.1.1.2.1.4.1.1.7.0.3161092.
PAGE 884
snmpwalk -v2c -c public 10.16.150.83 1.0.8802.1.1.2.1.4.4.1.4 iso.0.8802.1.1.2.1.4.4.1.4.0.3161092.1.0.1.102.1.133 iso.0.8802.1.1.2.1.4.4.1.4.0.3161092.1.0.1.102.2.134 iso.0.8802.1.1.2.1.4.4.1.4.0.3161092.1.0.1.102.3.135 iso.0.8802.1.1.2.1.4.4.1.4.0.3161092.1.0.1.102.4.136 iso.0.8802.1.1.2.1.4.4.1.4.0.3161092.1.0.1.102.5.137 = = = = = STRING: STRING: STRING: STRING: STRING: "Dell" "Dell" "Dell" "Dell" "Dell" snmpget -v2c -c public 10.16.150.102 1.0.8802.1.1.2.1.4.4.1.4.0.1048580.2.0.1.232.16.1 iso.0.
PAGE 885
MIB Object OID Access or Permission Description dellNetPortSecIfSecureMacLimit 1.3.6.1.4.1.6027.3.31.1.2.1.1.3 read-write Maximum number (N) of MAC addresses to be secured on the interface dellNetPortSecIfCurrentMacCou 1.3.6.1.4.1.6027.3.31.1.2.1.1.4 nt read-only Current number of MAC addresses learnt or configured on this interface dellNetPortSecIfStationMoveEn 1.3.6.1.4.1.6027.3.31.1.2.1.1.
PAGE 886
MAC addresses cannot be retrieved using dellNetPortSecSecureStaticMacAddrTable and dellNetPortSecSecureMacAddrTable. These tables are valid only if port security feature is enabled globally in the system. Table 122. MIB Objects for configuring MAC addresses MIB Object OID dellNetPortSecIfSecureStaticMa 1.3.6.1.4.1.6027.3.31.1.2.2.1.4 cRowStatus Access or Permission Description read-write Allows adding or deleting entries to or from the table dellNetPortSecSecureStaticMac AddrTable.
PAGE 887
Manage VLANs using SNMP The qBridgeMIB managed objects in Q-BRIDGE-MIB, defined in RFC 2674, allows you to use SNMP to manage VLANs. Creating a VLAN To create a VLAN, use the dot1qVlanStaticRowStatus object. The snmpset operation shown in the following example creates VLAN 10 by specifying a value of 4 for instance 10 of the dot1qVlanStaticRowStatus object. > snmpset -v2c -c mycommunity 123.45.6.78 .1.3.6.1.2.1.17.7.1.4.3.1.5.10 i 4 SNMPv2-SMI::mib-2.17.7.1.4.3.1.5.
PAGE 888
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SNMPv2-SMI::mib-2.17.7.1.4.3.1.4.1107787786 = Hex-STRING: 40 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 In the following example, Port 0/2 is added as a tagged member of VLAN 10.
PAGE 889
show interface Or, from the management system, use the snmpwwalk command to identify the interface index. 3. Enter the snmpset command to change the admin status using either the object descriptor or the OID. snmpset with descriptor: snmpset -v version -c community agent-ip ifAdminStatus.ifindex i {1 | 2} snmpset with OID: snmpset -v version -c community agent-ip .1.3.6.1.2.1.2.2.1.7.ifindex i {1 | 2} Choose integer 1 to change the admin status to Up, or 2 to change the admin status to Down.
PAGE 890
---------------Query from Management Station--------------->snmpwalk -v 2c -c techpubs 10.11.131.162 .1.3.6.1.2.1.17.7.1.2.2.1 Use dot3aCurAggFdbTable to fetch the learned MAC address of a port-channel. The instance number is the decimal conversion of the MAC address concatenated with the port-channel number.
PAGE 891
Figure 137. Interface Index Number Assigned to FortyGigE 0/4 Port In this example, if you start from the least significant bit on the right: • • • • • The first 14 bits (00001000000010) identify a line card. The next 4 bits (1001) identify a 40-Gigabit Ethernet interface. The next 12 bits (000011000100) identify slot 0 and port 4. The next bit (0) identifies a physical interface. The last bit is always 0, which means that it is unused.
PAGE 892
• • • • • • • • • • • • • sho run bgp router bgp 100 address-family ipv4 vrf vrf1 snmp context context1 neighbor 20.1.1.1 remote-as 200 neighbor 20.1.1.1 no shutdown exit-address-family address-family ipv4 vrf vrf2 snmp context context2 timers bgp 30 90 neighbor 30.1.1.1 remote-as 200 neighbor 30.1.1.1 no shutdown exit-address-family To map the context to a VRF instance for SNMPv3, follow these steps: 1. Create a community and map a VRF to it.
PAGE 893
Example of SNMP Walk Output for BGP timer configured for vrf2 (SNMPv2c) snmpwalk -v 2c -c vrf2 10.16.131.125 1.3.6.1.4.1.6027.20.1.2.3 SNMPv2-SMI::enterprises.6027.20.1.2.3.1.1.1.0.1.30.1.1.2.1.30.1.1.1 SNMPv2-SMI::enterprises.6027.20.1.2.3.1.1.2.0.1.30.1.1.2.1.30.1.1.1 SNMPv2-SMI::enterprises.6027.20.1.2.3.2.1.1.0.1.30.1.1.2.1.30.1.1.1 SNMPv2-SMI::enterprises.6027.20.1.2.3.2.1.2.0.1.30.1.1.2.1.30.1.1.1 SNMPv2-SMI::enterprises.6027.20.1.2.3.2.1.3.0.1.30.1.1.2.1.30.1.1.1 SNMPv2-SMI::enterprises.6027.20.1.2.
PAGE 894
Example of Viewing Changed Interface State for Monitored Ports SNMPv2-MIB::sysUpTime.0 = Timeticks: (8500842) 23:36:48.42 SNMPv2-MIB::snmpTrapOID.0 = OID: IF-MIB::linkDown IF-MIB::ifIndex.33865785 = INTEGER: 33865785 SNMPv2-SMI::enterprises.6027.3.1.1.4.1.2 = STRING: "OSTATE_DN: Changed interface state to down: Te 0/0" 2010-02-10 14:22:39 10.16.130.4 [10.16.130.4]: SNMPv2-MIB::sysUpTime.0 = Timeticks: (8500842) 23:36:48.42 SNMPv2-MIB::snmpTrapOID.0 = OID: IF-MIB::linkDown IF-MIB::ifIndex.
PAGE 895
Field (OID) Description SNMPv2-SMI::enterprises.6027.3.11.1.3.1.1.4 Vendor Name SNMPv2-SMI::enterprises.6027.3.11.1.3.1.1.5 Part Number SNMPv2-SMI::enterprises.6027.3.11.1.3.1.1.6 Serial Number SNMPv2-SMI::enterprises.6027.3.11.1.3.1.1.7 Transmit Power SNMPv2-SMI::enterprises.6027.3.11.1.3.1.1.8 Receive Power Configuring SNMP context name To configure the SNMP context name for OSPFv3 module, use the following command. • Configure the SNMP context-name.
PAGE 896
54 Storm Control Storm control allows you to control unknown-unicast, muticast, and broadcast traffic on Layer 2 and Layer 3 physical interfaces. Dell Networking Operating System (OS) Behavior: Dell Networking OS supports unknown-unicast, muticast, and broadcast control (the storm-control broadcast command) for Layer 2 and Layer 3 traffic. To view the storm control broadcast configuration show storm-control broadcast | multicast | unknown-unicast | pfc-llfc[interface] command.
PAGE 897
• storm-control multicast packets_per_second in Shut down the port if it receives the PFC/LLFC packets more than the configured rate. INTERFACE mode storm-control pfc-llfc pps in shutdown NOTE: PFC/LLFC storm control enabled interface disables the interfaces if it receives continuous PFC/LLFC packets. It can be a result of a faulty NIC/Switch that sends spurious PFC/LLFC packets.
PAGE 898
55 Spanning Tree Protocol (STP) The spanning tree protocol (STP) is a Layer 2 protocol — specified by IEEE 802.1d — that eliminates loops in a bridged topology by enabling only a single path through the network.
PAGE 899
• • • Prevent Network Disruptions with BPDU Guard STP Root Guard Enabling SNMP Traps for Root Elections and Topology Changes Important Points to Remember • • • • • STP is disabled by default. The Dell Networking OS supports only one spanning tree instance (0). For multiple instances, enable the multiple spanning tree protocol (MSTP) or per-VLAN spanning tree plus (PVST+). You may only enable one flavor of spanning tree at any one time.
PAGE 900
no ip address 2. Place the interface in Layer 2 mode. INTERFACE switchport 3. Enable the interface. INTERFACE mode no shutdown To verify that an interface is in Layer 2 mode and enabled, use the show config command from INTERFACE mode. Dell(conf-if-te-1/1)#show config ! interface TenGigabitEthernet 1/1 no ip address switchport no shutdown Dell(conf-if-te-1/1)# Enabling Spanning Tree Protocol Globally Enable the spanning tree protocol globally; it is not enabled by default.
PAGE 901
2. Enable STP. PROTOCOL SPANNING TREE mode no disable To disable STP globally for all Layer 2 interfaces, use the disable command from PROTOCOL SPANNING TREE mode. To verify that STP is enabled, use the show config command from PROTOCOL SPANNING TREE mode.
PAGE 902
Adding an Interface to the Spanning Tree Group To add a Layer 2 interface to the spanning tree topology, use the following command. • Enable spanning tree on a Layer 2 interface. INTERFACE mode spanning-tree 0 To remove a Layer 2 interface from the spanning tree topology, enter the no spanning-tree 0 command. Modifying Global Parameters You can modify the spanning tree parameters.
PAGE 903
To view the current values for global parameters, use the show spanning-tree 0 command from EXEC privilege mode. Refer to the second example in Enabling Spanning Tree Protocol Globally. Modifying Interface STP Parameters You can set the port cost and port priority values of interfaces in Layer 2 mode. • • Port cost — a value that is based on the interface type. The greater the port cost, the less likely the port is selected to be a forwarding port.
PAGE 904
Prevent Network Disruptions with BPDU Guard Configure the Portfast (and Edgeport, in the case of RSTP, PVST+, and MSTP) feature on ports that connect to end stations. End stations do not generate BPDUs, so ports configured with Portfast/ Edgport (edgeports) do not expect to receive BDPUs. If an edgeport does receive a BPDU, it likely means that it is connected to another part of the network, which can negatively affect the STP topology.
PAGE 905
Figure 140. Enabling BPDU Guard Dell EMC Networking OS Behavior BPDU guard: • • is used on edgeports and blocks all traffic on edgeport if it receives a BPDU. drops the BPDU after it reaches the RP and generates a console message. Example of Blocked BPDUs Selecting STP Root The STP determines the root bridge, but you can assign one bridge a lower priority to increase the likelihood that it becomes the root bridge. You can also specify that a bridge is the root or the secondary root.
PAGE 906
STP Root Guard Use the STP root guard feature in a Layer 2 network to avoid bridging loops. In STP, the switch in the network with the lowest priority (as determined by STP or set with the bridge-priority command) is selected as the root bridge. If two switches have the same priority, the switch with the lower MAC address is selected as the root. All other switches in the network use the root bridge as the reference used to calculate the shortest forwarding path.
PAGE 907
Configuring Root Guard Enable STP root guard on a per-port or per-port-channel basis. Dell Networking OS Behavior: The following conditions apply to a port enabled with STP root guard: • • • • • Root guard is supported on any STP-enabled port or port-channel interface.
PAGE 908
As shown in STP topology 3 (bottom middle), after you enable loop guard on an STP port or port-channel on Switch C, if no BPDUs are received and the max-age timer expires, the port transitions from a blocked state to a Loop-Inconsistent state (instead of to a Forwarding state). Loop guard blocks the STP port so that no traffic is transmitted and no loop is created. As soon as a BPDU is received on an STP port in a Loop-Inconsistent state, the port returns to a blocking state.
PAGE 909
• Enabling Portfast BPDU guard and loop guard at the same time on a port results in a port that remains in a blocking state and prevents traffic from flowing through it. For example, when Portfast BPDU guard and loop guard are both configured: • • If a BPDU is received from a remote device, BPDU guard places the port in an Err-Disabled Blocking state and no traffic is forwarded on the port.
PAGE 910
56 SupportAssist SupportAssist sends troubleshooting data securely to Dell. SupportAssist in this Dell Networking OS release does not support automated email notification at the time of hardware fault alert, automatic case creation, automatic part dispatch, or reports. SupportAssist requires Dell Networking OS 9.9(0.0) and SmartScripts 9.7 or later to be installed on the Dell Networking device. For more information on SmartScripts, see Dell Networking Open Automation guide. Figure 143.
PAGE 911
Configuring SupportAssist Using a Configuration Wizard You are guided through a series of queries to configure SupportAssist. The generated commands are added to the running configuration, including the DNS resolve commands, if configured. This command starts the configuration wizard for the SupportAssist. At any time, you can exit by entering Ctrl-C. If necessary, you can skip some data entry. Enable the SupportAssist service.
PAGE 912
the collection, transmission and/or use of the Collected Data, you may not download, install or otherwise use SupportAssist. NOTE: This step is not mandatory and you can configure SupportAssist manually without performing this step. Even before you accept or reject the EULA, the configuration data is sent to the default centrally deployed SupportAssist Server. If you reject the EULA, the configuration data is not transmitted to the SupportAssist server. 2. Move to the SupportAssist Configuration mode.
PAGE 913
Configuring SupportAssist Activity SupportAssist Activity mode allows you to configure and view the action-manifest file for a specific activity. To configure SupportAssist activity, use the following commands. 1. Move to the SupportAssist Activity mode for an activity. Allows you to configure customized details for a specific activity.
PAGE 914
By default, the full transfer includes the core files. When you disable the core transfer activity, the full transfer excludes the core files.
PAGE 915
[no] contact-person [first ] last Dell(conf-supportassist)#contact-person first john last doe Dell(conf-supportassist-pers-john_doe)# 2. Configure the email addresses to reach the contact person. SUPPORTASSIST PERSON mode [no] email-address primary email-address [alternate email-address] Dell(conf-supportassist-pers-john_doe)#email-address primary jdoe@mycompany.com Dell(conf-supportassist-pers-john_doe)# 3. Configure phone numbers of the contact person.
PAGE 916
[no] enable Dell(conf-supportassist-serv-default)#enable Dell(conf-supportassist-serv-default)# 4. Configure the URL to reach the SupportAssist remote server. SUPPORTASSIST SERVER mode [no] url uniform-resource-locator Dell(conf-supportassist-serv-default)#url https://192.168.1.1/index.htm Dell(conf-supportassist-serv-default)# Viewing SupportAssist Configuration To view the SupportAssist configurations, use the following commands: 1.
PAGE 917
url http://1.1.1.1:1337 Dell# 3. Display the EULA for the feature. EXEC Privilege mode show eula-consent {support-assist | other feature} Dell#show eula-consent support-assist SupportAssist EULA has been: Accepted Additional information about the SupportAssist EULA is as follows: By installing SupportAssist, you allow Dell to save your contact information (e.g. name, phone number and/or email address) which would be used to provide technical support for your Dell products and services.
PAGE 918
57 System Time and Date System time and date settings are user-configurable and maintained through the network time protocol (NTP). System times and dates are also set in hardware settings using the Dell Networking OS CLI. Topics: • • Network Time Protocol Time and Date Network Time Protocol The network time protocol (NTP) synchronizes timekeeping among a set of distributed time servers and clients. The protocol also coordinates time distribution in a large, diverse network with various interfaces.
PAGE 919
Protocol Overview The NTP messages to one or more servers and processes the replies as received. The server interchanges addresses and ports, fills in or overwrites certain fields in the message, recalculates the checksum, and returns it immediately. Information included in the NTP message allows each client/server peer to determine the timekeeping characteristics of its other peers, including the expected accuracies of their clocks.
PAGE 920
To display the system clock state with respect to NTP, use the show ntp status command from EXEC Privilege mode. DellEMC#show ntp status Clock is synchronized, stratum 4, reference is 10.16.151.117, vrf-id is 0 frequency is -44.862 ppm, stability is 0.050 ppm, precision is -18 reference time deeef7ef.85eeaa10 Tue, Jul 10 2018 9:16:31.523 UTC clock offset is -0.167449 msec, root delay is 149.194 msec root dispersion is 54.557 msec, peer dispersion is 0.
PAGE 921
• • • • For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. For the Management interface, enter the keyword ManagementEthernet then the slot/port information. For a port channel interface, enter the keywords port-channel then a number. For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. To view the configuration, use the show running-config ntp command in EXEC privilege mode (refer to the example in Configuring NTP Authentication).
PAGE 922
To configure the switch as NTP Server use the ntp master command. stratum number identifies the NTP Server's hierarchy. The following example shows configuring an NTP server. Dell EMC(conf)#show running-config ntp ! ntp master ntp server 10.16.127.44 ntp server 10.16.127.86 ntp server 10.16.127.
PAGE 923
To view the NTP configuration, use the show running-config ntp command in EXEC privilege mode. The following example shows an encrypted authentication key (in bold). All keys are encrypted. DellEMC#show running ntp ! ntp authenticate ntp authentication-key 345 md5 5A60910F3D211F02 ntp server 11.1.1.1 version 3 ntp trusted-key 345 DellEMC# Configuring NTP control key password The Network Time Protocal daemon (NTPD) design uses NTPQ to configure NTPD.
PAGE 924
• Set the system software clock to the current time and date. EXEC Privilege mode clock set time month day year • • • • time: enter the time in hours:minutes:seconds. For the hour variable, use the 24-hour format; for example, 17:15:00 is 5:15 pm. month: enter the name of one of the 12 months in English. You can enter the name of a day to change the order of the display to time day month year. day: enter the number of the day. The range is from 1 to 31.
PAGE 925
• • • • • • start-time: enter the time in hours:minutes. For the hour variable, use the 24-hour format; example, 17:15 is 5:15 pm. end-month: enter the name of one of the 12 months in English. You can enter the name of a day to change the order of the display to time day month year. end-day: enter the number of the day. The range is from 1 to 31. You can enter the name of a month to change the order of the display to time day month year. end-year: enter a four-digit number as the year.
PAGE 926
pacific Sat Nov 7 2009" NOTE: If you enter after entering the recurring command parameter, and you have already set a one-time daylight saving time/date, the system uses that time and date as the recurring setting. To view the clock summer-time recurring parameters, use the clock summer-time recurring ? command.
PAGE 927
58 Tunneling Tunnel interfaces create a logical tunnel for IPv4 or IPv6 traffic. Tunneling supports RFC 2003, RFC 2473, and 4213. DSCP, hop-limits, flow label values, OSPFv2, and OSPFv3 are also supported. ICMP error relay, PATH MTU transmission, and fragmented packets are not supported.
PAGE 928
tunnel mode ipv6ip no shutdown The following sample configuration shows a tunnel configured in IPIP mode (IPv4 tunnel carries IPv4 and IPv6 traffic): Dell(conf)#interface tunnel 3 Dell(conf-if-tu-3)#tunnel source 5::5 Dell(conf-if-tu-3)#tunnel destination 8::9 Dell(conf-if-tu-3)#tunnel mode ipv6 Dell(conf-if-tu-3)#ip address 3.1.1.1/24 Dell(conf-if-tu-3)#ipv6 address 3::1/64 Dell(conf-if-tu-3)#no shutdown Dell(conf-if-tu-3)#show config ! interface Tunnel 3 ip address 3.1.1.
PAGE 929
The following sample configuration shows how to configure a tunnel allow-remote address. Dell(conf)#interface tunnel 1 Dell(conf-if-tu-1)#ipv6 address 1abd::1/64 Dell(conf-if-tu-1)#ip address 1.1.1.1/24 Dell(conf-if-tu-1)#tunnel source 40.1.1.1 Dell(conf-if-tu-1)#tunnel mode ipip decapsulate-any Dell(conf-if-tu-1)#tunnel allow-remote 40.1.1.2 Dell(conf-if-tu-1)#no shutdown Dell(conf-if-tu-1)#show config ! interface Tunnel 1 ip address 1.1.1.1/24 ipv6 address 1abd::1/64 tunnel source 40.1.1.
PAGE 930
• • • Control-plane packets received on a multipoint receive-only tunnel are destined to the local IP address and routed to the CPU after decapsulation. A response to these packets from the switch is only possible if the route to the sender does not pass through a receiveonly tunnel. Multipathing over more than one VLAN interface is not supported on packets routed through the tunnel interface. IP tunnel interfaces are supported over ECMP paths to the next hop.
PAGE 931
59 Upgrade Procedures To find the upgrade procedures, go to the Dell EMC Networking OS Release Notes for your system type to see all the requirements needed to upgrade to the desired Dell EMC Networking OS version. To upgrade your system type, follow the procedures in the Dell EMC Networking OS Release Notes. You can download the release notes of your platform at https://www.force10networks.com. Use your login ID to log in to the website.
PAGE 932
60 Uplink Failure Detection (UFD) Feature Description A switch provides upstream connectivity for devices, such as servers. If a switch loses its upstream connectivity, downstream devices also lose their connectivity. However, the devices do not receive a direct indication that upstream connectivity is lost because connectivity to the switch is still operational UFD allows a switch to associate downstream interfaces with upstream interfaces.
PAGE 933
Figure 145. Uplink Failure Detection How Uplink Failure Detection Works UFD creates an association between upstream and downstream interfaces. The association of uplink and downlink interfaces is called an uplink-state group. An interface in an uplink-state group can be a physical interface or a port-channel (LAG) aggregation of physical interfaces. An enabled uplink-state group tracks the state of all assigned upstream interfaces.
PAGE 934
Figure 146. Uplink Failure Detection Example If only one of the upstream interfaces in an uplink-state group goes down, a specified number of downstream ports associated with the upstream interface are put into a Link-Down state. You can configure this number and is calculated by the ratio of the upstream port bandwidth to the downstream port bandwidth in the same uplink-state group.
PAGE 935
• If you disable an uplink-state group, the downstream interfaces are not disabled regardless of the state of the upstream interfaces. • • If an uplink-state group has no upstream interfaces assigned, you cannot disable downstream interfaces when an upstream link goes down. To enable the debug messages for events related to a specified uplink-state group or all groups, use the debug uplink-stategroup [group-id] command, where the group-id is from 1 to 16.
PAGE 936
The maximum length is 80 alphanumeric characters. 6. (Optional) Disables upstream-link tracking without deleting the uplink-state group. UPLINK-STATE-GROUP mode no enable The default is upstream-link tracking is automatically enabled in an uplink-state group. To re-enable upstream-link tracking, use the enable command. Clearing a UFD-Disabled Interface You can manually bring up a downstream interface in an uplink-state group that UFD disabled and is in a UFD-Disabled Error state.
PAGE 937
Displaying Uplink Failure Detection To display information on the UFD feature, use any of the following commands. • Display status information on a specified uplink-state group or all groups. EXEC mode show uplink-state-group [group-id] [detail] • • group-id: The values are 1 to 16. • detail: displays additional status information on the upstream and downstream interfaces in each group. Display the current status of a port or port-channel interface assigned to an uplink-state group.
PAGE 938
Upstream Interfaces : Te 0/41(Dwn) Po 8(Dwn) Downstream Interfaces : Te 0/40(Dwn) The following example shows viewing the uplink state group interface status for an S50 system.
PAGE 939
• Verify the configuration with various show commands.
PAGE 940
61 Virtual LANs (VLANs) Virtual LANs (VLANs) are a logical broadcast domain or logical grouping of interfaces in a local area network (LAN) in which all data received is kept locally and broadcast to all members of the group. When in Layer 2 mode, VLANs move traffic at wire speed and can span multiple devices. The system supports up to 4093 port-based VLANs and one default VLAN, as specified in IEEE 802.1Q.
PAGE 941
• A tagged interface requires an additional step to remove it from Layer 2 mode. Because tagged interfaces can belong to multiple VLANs, remove the tagged interface from all VLANs using the no tagged interface command. Only after the interface is untagged and a member of the Default VLAN can you use the no switchport command to remove the interface from Layer 2 mode. For more information, refer to VLANs and Port Tagging.
PAGE 942
Configuration Task List This section contains the following VLAN configuration tasks.
PAGE 943
NOTE: You cannot configure an existing switchport or port channel interface for Native VLAN. Interfaces must have no other Layer 2 or Layer 3 configurations when using the portmode hybrid command or a message similar to this displays: % Error: Port is in Layer-2 mode Te 5/6. To configure a port so that it can be a member of an untagged and tagged VLANs, use the following commands. 1. Remove any Layer 2 or Layer 3 configurations from the interface. INTERFACE mode 2. Configure the interface for Hybrid mode.
PAGE 944
Assigning Interfaces to a VLAN You can only assign interfaces in Layer 2 mode to a VLAN using the tagged and untagged commands. To place an interface in Layer 2 mode, use the switchport command. You can further designate these Layer 2 interfaces as tagged or untagged. For more information, refer to the Interfaces chapter and Configuring Layer 2 (Data Link) Mode.
PAGE 945
When you remove a tagged interface from a VLAN (using the no tagged interface command), it remains tagged only if it is a tagged interface in another VLAN. If the tagged interface is removed from the only VLAN to which it belongs, the interface is placed in the Default VLAN as an untagged interface. Moving Untagged Interfaces To move untagged interfaces from the Default VLAN to another VLAN, use the following commands. 1. Access INTERFACE VLAN mode of the VLAN to which you want to assign the interface.
PAGE 946
62 VLT Proxy Gateway Proxy Gateway in VLT Domains Using a proxy gateway, the VLT peers in a domain can route the L3 packets destined for VLT peers in another domain as long as they have L3 reachability for the IP destinations. A proxy gateway in a VLT domain provides the following benefits: • • Avoids sub-optimal routing of packets by a VLT domain when packets are destined to the endpoint in another VLT domain.
PAGE 947
Figure 148. VLT Proxy Gateway — Topology 1 Guidelines for Enabling the VLT Proxy Gateway Keep the following points in mind when you enable this functionality: 1. The proxy gateway is supported only for VLT; for example, across VLT domain. 2. To get full benefits out of proxy gateway, peer-routing is recommended 3.
PAGE 948
13. When a VM moves from one VLT domain to the another VLT domain, the VM host sends the gratuitous GARP. The GARP triggers a mac movement from the previous VLT domain to the newer VLT domain. 14. After a station move, if a host sends a TTL1 packet destined to its gateway; for example, a previous VLT node, the packet may be dropped. 15. After a station move, if a host first PINGs its gateway; for example, a previous VLT node it results a 40 to 60% success rate considering it takes a longer path.
PAGE 949
• LLDP packets fail to reach the remote VLT domain devices (due to system down, rebooting, port down or physical link connection) Sample Configurations for LLDP VLT Proxy Gateway Apply the following configurations in the Core L3 Routers C and D in the local VLT domain and C1 and D1 in the remote VLT domain: 1. Configure proxy-gateway lldp in VLT Domain CONFIG mode. 2. Configure peer-domain-link port-channel in VLT Domain Proxy Gateway LLDP mode.
PAGE 950
1. The above figure (Topology 2) shows a sample VLT Proxy gateway scenario. There are no diagonal links in the square VLT connection between the C and D in VLT domain 1 and C1 and D1 in the VLT domain 2. This undergoes sub-optimal routing with the VLT Proxy Gateway LLDP method. For VLT Proxy Gateway to work in this scenario you must configure the , VLT-peer-mac transmit command under VLT Domain Proxy Gateway LLDP mode, in both C and D (VLT domain 1) and C1 and D1 (VLT domain 2).
PAGE 951
Dell(conf)#vlt domain domain-id 2. Configure the LLDP proxy gateway. VLT DOMAIN mode Dell(conf-vlt-domain)#proxy-gateway lldp 3. You can configure the port channel interface for an LLDP proxy gateway and exclude a VLAN or a range of VLANs from proxy routing. This parameter is for an LLDP proxy gateway configuration. VLT DOMAIN PROXY GW LLDP mode Dell(conf-vlt-domain-proxy-gw-lldp)#peer-domain-link port-channel interface exclude-vlan vlan-range 4. Display the VLT proxy gateway configuration.
PAGE 952
63 Virtual Routing and Forwarding (VRF) VRF Overview VRF improves functionality by allowing network paths to be segmented without using multiple devices. Using VRF also increases network security and can eliminate the need for encryption and authentication due to traffic segmentation. Internet service providers (ISPs) often take advantage of VRF to create separate virtual private networks (VPNs) for customers; VRF is also referred to as VPN routing and forwarding.
PAGE 953
VRF Configuration Notes Although there is no restriction on the number of VLANs that can be assigned to a VRF instance, the total number of routes supported in VRF is limited by the size of the IPv4 CAM. VRF is implemented in a network device by using Forwarding Information Bases (FIBs). A network device may have the ability to configure different virtual routers, where entries in the FIB that belong to one VRF cannot be accessed by another VRF on the same device.
PAGE 954
Feature/Capability Support Status for Default VRF Support Status for Non-default VRF default-VRF only. PBR supported on default-VRF only. QoS not supported on VLANs.
PAGE 955
• • Connect an OSPF Process to a VRF Instance Configure VRRP on a VRF Load VRF CAM VRF is enabled by default on the switch. To load the VRF CAM profile, enter the feature vrf command in global configuration mode. Table 129. Load VRF CAM Step Task Command Syntax Command Mode 1 Load CAM memory for the VRF feature. feature vrf CONFIGURATION After you load VRF CAM, CLI parameters that allow you to configure non-default VRFs are made available on the system.
PAGE 956
Task Command Syntax Command Mode ipv6 address 1::1 INTERFACE CONFIGURATION NOTE: You can assign either an IPv4 or an IPv6 address but not both. Assign an IPv6 address to the interface. NOTE: You can also auto configure an IPv6 address using the ipv6 address autoconfig command. View VRF Instance Information To display information about VRF configuration, enter the show ip vrf command. Table 133.
PAGE 957
Task Command Syntax Configure the VRRP group and virtual IP address View VRRP command output for the VRF vrf1 Command Mode vrrp-group 10 virtual-address 10.1.1.100 show config ----------------------------! interface TenGigabitEthernet 0/13 ip vrf forwarding vrf1 ip address 10.1.1.1/24 ! vrrp-group 10 virtual-address 10.1.1.100 no shutdown show vrrp vrf vrf1 -----------------TenGigabitEthernet 0/13, IPv4 VRID: 10, Version: 2, Net: 10.1.1.1 VRF: 2 vrf1 State: Master, Priority: 100, Master: 10.1.1.
PAGE 958
NOTE: The command line help still displays relevant details corresponding to each of these commands. However, these interface range or interface group commands are not supported when Management VRF is configured. Configuring a Static Route To configure a static route, perform the following steps: Table 136. Configuring a Static Route Task Command Syntax Command Mode Configure a static route that points to a management interface.
PAGE 959
Figure 151.
PAGE 960
Figure 152. Setup VRF Interfaces The following example relates to the configuration shown in the above illustrations. Router 1 Router 2 The following shows the output of the show commands on Router 1. Router 1 The following shows the output of the show commands on Router 2.
PAGE 961
Configuring Route Leaking with Filtering When you initalize route leaking from one VRF to another, all the routes are exposed to the target VRF. If the size of the source VRF's RTM is considerablly large, an import operation results in the duplication of the target VRF's RTM with the source RTM entries. To mitigate this issue, you can use route-maps to filter the routes that are exported and imported into the route targets based on certain matching criteria.
PAGE 962
When you import routes into VRF-blue using the route-map import_ospf_protocol, only OSPF routes are imported into VRF-blue. Even though VRF-red has leaked both OSPF as well as BGP routes to be shared with other VRFs, this command imports only OSPF routes into VRF-blue. 9. Configure the import target in the source VRF for reverse communnication with the destination VRF.
PAGE 963
A non-default VRF named VRF-Shared is created and the interface 1/4 is assigned to this VRF. 2. Configure the export target in the source VRF:.ip route-export 1:1 3. Configure VRF-red.ip vrf vrf-red ip vrf forwarding VRF-red ip address x.x.x.x 255.x.x.x A non-default VRF named VRF-red is created and the interface 1/11 is assigned to this VRF. 4. Configure the import target in VRF-red.ip route-import 1:1 5. Configure the export target in VRF-red.ip route-export 2:2 6. Configure VRF-blue.
PAGE 964
64 Virtual Link Trunking (VLT) Overview In a traditional switched topology as shown below, spanning tree protocols (STPs) are used to block one or more links to prevent loops in the network. Although loops are prevented, bandwidth of all links is not effectively utilized by the connected devices. Figure 153. Traditional switched topology VLT not only overcomes this caveat, but also provides a multipath to the connected devices.
PAGE 965
To prevent the initial loop that may occur prior to VLT being established, use a spanning tree protocol. After VLT is established, you may use rapid spanning tree protocol (RSTP) to prevent loops from forming with new links that are incorrectly connected and outside the VLT domain. VLT provides Layer 2 multipathing, creating redundancy through increased bandwidth, enabling multiple parallel paths between nodes, and load-balancing traffic where alternate paths exist.
PAGE 966
The following example shows how VLT is deployed. The switches appear as a single virtual switch from the point of view of the switch or server supporting link aggregation control protocol (LACP). VLT on Core Switches You can also deploy VLT on core switches. Uplinks from servers to the access layer and from access layer to the aggregation layer are bundled in LAG groups with end-to-end Layer 2 multipathing.
PAGE 967
• • Bulk synchronization happens only for global IPv6 Neighbors; link-local neighbor entries are not synced. If all of the following conditions are true, MAC addresses may not be synced correctly: • • • • • • VLT peers use VLT interconnect (VLTi) Sticky MAC is enabled on an orphan port in the primary or secondary peer MACs are currently inactive If this scenario occurs, use the clear mac-address-table sticky all command on the primary or secondary peer to correctly sync the MAC addresses.
PAGE 968
• When you enable the VLTi link, the link between the VLT peer switches is established if the following configured information is true on both peer switches: • • the VLT system MAC address matches. the VLT unit-id is not identical. NOTE: If you configure the VLT system MAC address or VLT unit-id on only one of the VLT peer switches, the link between the VLT peer switches is not established. Each VLT peer switch must be correctly configured to establish the link between the peers.
PAGE 969
• • • • • • • • For detailed information about how to use VRRP in a VLT domain, see the following VLT and VRRP interoperability section. For information about configuring IGMP Snooping in a VLT domain, see VLT and IGMP Snooping. All system management protocols are supported on VLT ports, including SNMP, RMON, AAA, ACL, DNS, FTP, SSH, Syslog, NTP, RADIUS, SCP, TACACS+, Telnet, and LLDP. Enable Layer 3 VLAN connectivity VLT peers by configuring a VLAN network interface for the same VLAN on both switches.
PAGE 970
traffic assumes the role of the Primary Peer. If the original Primary Peer is restored, the VLT peer reassigned as the Primary Peer retains this role and the other peer must be reassigned as a Secondary Peer. Peer role changes are reported as SNMP traps. RSTP and VLT VLT provides loop-free redundant topologies and does not require RSTP. RSTP can cause temporary port state blocking and may cause topology changes after link or node failures.
PAGE 971
VLT and Stacking You cannot enable stacking on switches configured for VLT operation. If you enable stacking on a Dell Networking switch on which you want to enable VLT, you must first remove the unit from the existing stack. After you remove the unit, you can configure VLT on the switch. VLT IPv6 The following features have been enhanced to support VLT on IPv6. : • • • • • VLT Sync — Entries learned on the VLT interface are synced on both VLT peers.
PAGE 972
Figure 156. PIM-Sparse Mode Support on VLT On each VLAN where the VLT peer nodes act as the first hop or last hop routers, one of the VLT peer nodes is elected as the PIM designated router. If you configured IGMP snooping along with PIM on the VLT VLANs, you must configure VLTi as the static multicast router port on both VLT peer switches. This ensures that for first hop routers, the packets from the source are redirected to the designated router (DR) if they are incorrectly hashed.
PAGE 973
If the VLT node elected as the designated router fails and you enable VLT Multicast Routing, multicast routes are synced to the other peer for traffic forwarding to ensure minimal traffic loss. If you did not enable VLT Multicast Routing, traffic loss occurs until the other VLT peer is selected as the DR. VLT Routing VLT unicast and multicast routing is supported on the switch. Layer 2 protocols from the ToR to the server are intra-rack and inter-rack.
PAGE 974
value: Specify a value (in seconds) from 1 to 65535. VLT Multicast Routing VLT Multicast Routing provides resiliency to multicast routed traffic during the multicast routing protocol convergence period after a VLT link or VLT peer fails using the least intrusive method (PIM) and does not alter current protocol behavior. Unlike VLT Unicast Routing, a normal multicast routing protocol does not exchange multicast routes between VLT peers.
PAGE 975
Non-VLT ARP Sync Synchronization for non-ARP routing table entries is supported on the switch. ARP entries (including ND entries) learned on other ports are synced with the VLT peer to support station move scenarios. NOTE: ARP entries learned on non-VLT, non-spanned VLANs are not synced with VLT peers. RSTP Configuration RSTP is supported in a VLT domain. Before you configure VLT on peer switches, configure RSTP in the network. RSTP is required for initial loop prevention during the VLT startup phase.
PAGE 976
Configure RSTP on VLT Peers to Prevent Forwarding Loops (VLT Peer 1) Dell_VLTpeer1(conf)#protocol spanning-tree rstp Dell_VLTpeer1(conf-rstp)#no disable Dell_VLTpeer1(conf-rstp)#bridge-priority 4096 Configure RSTP on VLT Peers to Prevent Forwarding Loops (VLT Peer 2) Dell_VLTpeer2(conf)#protocol spanning-tree rstp Dell_VLTpeer2(conf-rstp)#no disable Dell_VLTpeer2(conf-rstp)#bridge-priority 0 Configuring VLT VLT requires that you enable the feature and then configure the same VLT domain, backup link, and V
PAGE 977
no shutdown 5. Repeat Steps 1 to 4 on the VLT peer switch to configure the VLT interconnect. Enabling VLT and Creating a VLT Domain To enable VLT and create a VLT domain: 1. Enable VLT on a switch, then configure a VLT domain and enter VLT-domain configuration mode. CONFIGURATION mode vlt domain domain-id The domain ID range is from 1 to 1000. Configure the same domain ID on the peer switch to allow for common peering. VLT uses the domain ID to automatically create a VLT MAC address for the domain.
PAGE 978
3. Ensure that the interface is active. MANAGEMENT INTERFACE mode no shutdown 4. Configure a VLT backup link using the back-up destination command. VLT domain mode back-up destination {ip address ipv4-address/mask | ipv6 address ipv6-address/mask} Dell(conf-vlt-domain)#back-up destination ? A.B.C.D IP address for VLT backup link ipv6 Configure IPv6 address for VLT backup link IPv4 address (A.B.C.D) or IPv6 address (X:X:X:X::X) of the VLT peer’s management interface. 5.
PAGE 979
Connecting a VLT Domain to an Attached Access Device (Switch or Server) To connect a VLT domain to an attached access device, use the following commands. On a VLT peer switch: To connect to an attached device, configure the same port channel ID number on each peer switch in the VLT domain. 1. Configure the same port channel to be used to connect to an attached device and enter interface configuration mode. CONFIGURATION mode interface port-channel id-number 2. Remove an IP address from the interface.
PAGE 980
peer-link port-channel id-number peer-down-vlan vlan interface-number The range is from 1 to 4094. Configuring Enhanced VLT (eVLT) (Optional) To configure enhanced VLT (eVLT) between two VLT domains on your network, use the following procedure. For a sample configuration, refer to eVLT Configuration Example. To set up the VLT domain, use the following commands. 1. Configure the port channel to be used for the VLT interconnect on a VLT switch and enter interface configuration mode.
PAGE 981
interface port-channel id-number Enter the same port-channel number configured with the peer-link port-channel command in the Enabling VLT and Creating a VLT Domain. 9. Place the interface in Layer 2 mode. INTERFACE PORT-CHANNEL mode switchport 10. Associate the port channel to the corresponding port channel in the VLT peer for the VLT connection to an attached device. INTERFACE PORT-CHANNEL mode vlt-peer-lag port-channel id-number Valid port-channel ID numbers are from 1 to 128. 11.
PAGE 982
show interfaces interface 8. Configure the VLT links between VLT peer 1 and VLT peer 2 to the top of rack unit (shown in the following example). 9. Configure the static LAG/LACP between ports connected from VLT peer 1 and VLT peer 2 to the top of rack unit. EXEC Privilege mode show running-config entity 10. Configure the VLT peer link port channel id in VLT peer 1 and VLT peer 2. EXEC mode or EXEC Privilege mode show interfaces interface 11. In the top of rack unit, configure LACP in the physical ports.
PAGE 983
Configure the VLT links between VLT peer 1 and VLT peer 2 to the Top of Rack unit. In the following example, port Te 0/40 in VLT peer 1 is connected to Te 0/48 of TOR and port Te 0/18 in VLT peer 2 is connected to Te 0/50 of TOR. 1. Configure the static LAG/LACP between the ports connected from VLT peer 1 and VLT peer 2 to the Top of Rack unit. 2. Configure the VLT peer link port channel id in VLT peer 1 and VLT peer 2. 3.
PAGE 984
Role: Role Priority: ICL Link Status: HeartBeat Status: VLT Peer Status: Local System MAC address: Remote System MAC address: Primary 32768 Up Up Up 00:01:e8:8c:4d:08 00:01:e8:8c:4d:1c Dell-2#show vlt detail Local LAG Id Peer LAG Id Local Status Active VLANs ------------ ----------- ------------ -----------2 2 Up 1000-1199 Verify that the VLT LAG is up in both VLT peer units.
PAGE 985
Domain_1_Peer1(conf)#vlt domain 1000 Domain_1_Peer1(conf-vlt-domain)# peer-link port-channel 1 Domain_1_Peer1(conf-vlt-domain)# back-up destination 10.16.130.11 Domain_1_Peer1(conf-vlt-domain)# system-mac mac-address 00:0a:00:0a:00:0a Domain_1_Peer1(conf-vlt-domain)# unit-id 0 Configure eVLT on Peer 1.
PAGE 986
Domain_2_Peer3(conf-if-range-te-0/16-17)# port-channel 100 mode active Domain_2_Peer3(conf-if-range-te-0/16-17)# no shutdown Next, configure the VLT domain and VLTi on Peer 4. Domain_2_Peer4#configure Domain_2_Peer4(conf)#interface port-channel 1 Domain_2_Peer4(conf-if-po-1)# channel-member TenGigabitEthernet 0/8-9 Domain_1_Peer4#no shutdown Domain_2_Peer4(conf)#vlt domain 200 Domain_2_Peer4(conf-vlt-domain)# peer-link port-channel 1 Domain_2_Peer4(conf-vlt-domain)# back-up destination 10.18.130.
PAGE 987
VLT_Peer2(conf-if-vl-4001)#ip igmp snooping mrouter interface port-channel 128 VLT_Peer2(conf-if-vl-4001)#exit VLT_Peer2(conf)#end Verifying a VLT Configuration To monitor the operation or verify the configuration of a VLT domain, use any of the following show commands on the primary and secondary VLT switches. • Display information on backup link operation. • EXEC mode show vlt backup-link Display general status information about VLT domains currently configured on the switch.
PAGE 988
VLT Backup Link ----------------Destination: Peer HeartBeat status: HeartBeat Timer Interval: HeartBeat Timeout: UDP Port: HeartBeat Messages Sent: HeartBeat Messages Received: 10.11.200.20 Up 1 3 34998 1030 1014 The following example shows the show vlt brief command.
PAGE 989
Local System MAC address: 00:01:e8:8a:df:bc Local System Role Priority: 32768 Dell_VLTpeer2# show vlt role VLT Role ---------VLT Role: System MAC address: System Role Priority: Local System MAC address: Local System Role Priority: Secondary 00:01:e8:8a:df:bc 32768 00:01:e8:8a:df:e6 32768 The following example shows the show running-config vlt command. Dell_VLTpeer1# show running-config vlt ! vlt domain 30 peer-link port-channel 60 back-up destination 10.11.200.
PAGE 990
Dell_VLTpeer2# show spanning-tree rstp brief Executing IEEE compatible Spanning Tree Protocol Root ID Priority 0, Address 0001.e88a.dff8 Root Bridge hello time 2, max age 20, forward delay 15 Bridge ID Priority 0, Address 0001.e88a.dff8 We are the root Configured hello time 2, max age 20, forward delay 15 Interface Designated Name PortID Prio Cost Sts Cost Bridge ID PortID ---------- -------- ---- ------- -------- - ------- ------------Po 1 128.2 128 200000 DIS 0 0 0001.e88a.dff8 128.2 Po 3 128.
PAGE 991
G - GVRP tagged, M - Vlan-stack, H - Hyperpull tagged NUM Status Description Q Ports 10 Active U Po110(Fo 0/52) T Po100(Fo 0/56,60) Configuring Virtual Link Trunking (VLT Peer 2) Enable VLT and create a VLT domain with a backup-link VLT interconnect (VLTi). Dell_VLTpeer2(conf)#vlt domain 999 Dell_VLTpeer2(conf-vlt-domain)#peer-link port-channel 100 Dell_VLTpeer2(conf-vlt-domain)#back-up destination 10.11.206.23 Dell_VLTpeer2(conf-vlt-domain)#exit Configure the backup link.
PAGE 992
Troubleshooting VLT To help troubleshoot different VLT issues that may occur, use the following information. NOTE: For information on VLT Failure mode timing and its impact, contact your Dell EMC Networking representative. Table 138. Troubleshooting VLT Description Behavior at Peer Up Behavior During Run Time Action to Take Bandwidth monitoring A syslog error message and an SNMP trap is generated when the VLTi bandwidth usage goes above the 80% threshold and when it drops below 80%.
PAGE 993
Description Behavior at Peer Up Behavior During Run Time A syslog error message is generated. A syslog error message is generated. Action to Take Reconfiguring Stacked Switches as VLT To convert switches that have been stacked to VLT peers, use the following procedure. 1. Remove the current configuration from the switches. You will need to split the configuration up for each switch. 2. Copy the files to the flash memory of the appropriate switch. 3.
PAGE 994
Association of VLTi as a Member of a PVLAN If a VLAN is configured as a non-VLT VLAN on both the peers, the VLTi link is made a member of that VLAN if the VLTi link is configured as a PVLAN or normal VLAN on both the peers. If a PVLAN is configured as a VLT VLAN on one peer and a non-VLT VLAN on another peer, the VLTi is added as a member of that VLAN by verifying the PVLAN parity on both the peers.
PAGE 995
Under such conditions, the IP stack performs the following operations: • • The ARP reply is sent with the MAC address of the primary VLAN. The ARP request packet originates on the primary VLAN for the intended destination IP address. The ARP request received on ICLs are not proxied, even if they are received with a secondary VLAN tag. This behavior change occurs because the node from which the ARP request was forwarded would have replied with its MAC address, and the current node discards the ARP request.
PAGE 996
VLT LAG Mode PVLAN Mode of VLT VLAN ICL VLAN Membership Mac Synchronization Peer1 Peer2 Peer1 Peer2 Access Access Secondary (Isolated) Secondary (Isolated) No No - Primary VLAN X - Primary VLAN Y No No Secondary (Community) Secondary (Community) No No - Primary VLAN Y - Primary VLAN X No No Access Access Promiscuous Access Primary Secondary No No Trunk Access Primary/Normal Secondary No No Configuring a VLT VLAN or LAG in a PVLAN You can configure the VLT peers or nodes
PAGE 997
peer-link port-channel id-number The range is from 1 to 128. 8. (Optional) To configure a VLT LAG, enter the VLAN ID number of the VLAN where the VLT forwards packets received on the VLTi from an adjacent peer that is down. VLT DOMAIN CONFIGURATION mode peer-link port-channel id-number peer-down-vlan vlan interface number The range is from 1 to 4094. Associating the VLT LAG or VLT VLAN in a PVLAN 1. Access INTERFACE mode for the port that you want to assign to a PVLAN.
PAGE 998
command in INTERFACE mode. If it is not listed in the show config command output, it is enabled. Only nondefault information is displayed in the show config command output. ARP proxy operation is performed on the VLT peer node IP address when the peer VLT node is down. The ARP proxy stops working either when the peer routing timer expires or when the peer VLT node goes up. Layer 3 VLT provides a higher resiliency at the Layer 3 forwarding level.
PAGE 999
To enable an explicit multicast routing table synchronization method for VLT nodes, you can configure VLT nodes as RPs. Multicast routing needs to identify the incoming interface for each route. The PIM running on both VLT peers enables both the peers to obtain traffic from the same incoming interface. You can configure a VLT node to be an RP through the ip pim rp-address command in Global Configuration mode.
PAGE 1000
unit-id 0 Dell# Configure VLT LAG as VLAN-Stack Access or Trunk Port Dell(conf)#interface port-channel 10 Dell(conf-if-po-10)#switchport Dell(conf-if-po-10)#vlt-peer-lag port-channel 10 Dell(conf-if-po-10)#vlan-stack access Dell(conf-if-po-10)#no shutdown Dell#show running-config interface port-channel 10 ! interface Port-channel 10 no ip address switchport vlan-stack access vlt-peer-lag port-channel 10 no shutdown Dell# Dell(conf)#interface port-channel 20 Dell(conf-if-po-20)#switchport Dell(conf-if-po-20)
PAGE 1001
Configure VLT LAG as VLAN-Stack Access or Trunk Port Dell(conf)#interface port-channel 10 Dell(conf-if-po-10)#switchport Dell(conf-if-po-10)#vlt-peer-lag port-channel 10 Dell(conf-if-po-10)#vlan-stack access Dell(conf-if-po-10)#no shutdown Dell#show running-config interface port-channel 10 ! interface Port-channel 10 no ip address switchport vlan-stack access vlt-peer-lag port-channel 10 no shutdown Dell# Dell(conf)#interface port-channel 20 Dell(conf-if-po-20)#switchport Dell(conf-if-po-20)#vlt-peer-lag po
PAGE 1002
ToR 1. Enable BFD globally. TOR(conf)# bfd enable 2. Configure a VLT peer LAG. 3. Configure the port channel for the VLT interconnect on a ToR. TOR(conf)# interface TOR(conf-if-po-111)# TOR(conf-if-po-111)# TOR(conf-if-po-111)# port-channel 10 no ip address switchport no shutdown 4. Configure a VLAN. TOR(conf)#interface vlan 100 TOR(conf-if-vl-100)#ip address 100.1.1.
PAGE 1003
4. Configure a VLT peer LAG. VLT_Primary(conf)#interface port-channel 10 VLT_Primary(conf-if-po-10)#no ip address VLT_Primary(conf-if-po-10)#switchport VLT_Primary(conf-if-po-10)#vlt-peer-lag port-channel 10 VLT_Primary(conf-if-po-10)#no shutdown 5. Configure a VLAN. VLT_Primary(conf)#interface vlan 100 VLT_Primary(conf-if-vl-100)#ip address 100.1.1.1/24 VLT_Primary(conf-if-vl-100)#tagged port-channel 10 VLT_Primary(conf-if-vl-100)#no shutdown VLT_Primary(conf-if-vl-100)#exit 6. Enable BFD over OSPF.
PAGE 1004
• To verify the VLTi (ICL) link is up in the VLT primary peer, use show vlt brief command.
PAGE 1005
65 Virtual Router Redundancy Protocol (VRRP) VRRP Overview VRRP is designed to eliminate a single point of failure in a statically routed network. Authentication is not supported on VRRPv3. VRRP is supported on “all types” of interfaces, including physical, VLAN, port-channel, and port extender interfaces. VRRP specifies a MASTER router that owns the next hop IP and MAC address for end stations on a local area network (LAN).
PAGE 1006
Figure 158. Basic VRRP Configuration VRRP Benefits With VRRP configured on a network, end-station connectivity to the network is not subject to a single point-of-failure. End-station connections to the network are redundant and are not dependent on internal gateway protocol (IGP) protocols to converge or update routing tables. VRRP Implementation Within a single VRRP group, up to 12 virtual IP addresses are supported.
PAGE 1007
Recommended Advertise Interval Groups/Interface Total VRRP Groups Between 250 and 450 2–3 seconds 24 Between 450 and 600 3–4 seconds 36 Between 600 and 800 4 seconds 48 Between 800 and 1000 5 seconds 84 Between 1000 and 1200 7 seconds 100 Between 1200 and 1500 8 seconds 120 VRRP Configuration By default, VRRP is not configured. Configuration Task List The following list specifies the configuration tasks for VRRP.
PAGE 1008
The following example shows verifying a VRRP configuration. Dell(conf-if-te-1/1)#show conf ! interface TenGigabitEthernet 1/1 ip address 10.10.10.
PAGE 1009
• If you configure multiple VRRP groups on an interface, only one of the VRRP Groups can contain the interface primary or secondary IP address. Configuring a Virtual IP Address To configure a virtual IP address, use the following commands. 1. Configure a VRRP group. INTERFACE mode vrrp-group vrrp-id The VRID range is from 1 to 255. 2. Configure virtual IP addresses for this VRID. INTERFACE -VRID mode virtual-address ip-address1 [...ip-address12] The range is up to 12 addresses.
PAGE 1010
Setting VRRP Group (Virtual Router) Priority Setting a virtual router priority to 255 ensures that router is the “owner” virtual router for the VRRP group. VRRP elects the MASTER router by choosing the router with the highest priority. The default priority for a virtual router is 100. The higher the number, the higher the priority. If the MASTER router fails, VRRP begins the election process to choose a new MASTER router based on the next-highest priority.
PAGE 1011
The bold section shows the encryption type (encrypted) and the password. Dell(conf-if-te-1/1/1-vrid-111)#authentication-type ? Dell(conf-if-te-1/1/1-vrid-111)#authentication-type simple 7 force10 The following example shows verifying the VRRP authentication configuration using the show conf command. The bold section shows the encrypted password. Dell(conf-if-te-1/1/1-vrid-111)#show conf ! vrrp-group 111 authentication-type simple 7 387a7f2df5969da4 priority 255 virtual-address 10.10.10.1 virtual-address 10.
PAGE 1012
If are using VRRP version 2, you must configure the timer values in multiple of whole seconds. For example a timer value of 3 seconds or 300 centisecs are valid and equivalent. However, a time value of 50 centisecs is invalid because it not a multiple of 1 second. If you are using VRRP version 3, you must configure the timer values in multiples of 25 centisecs. If you are configured for VRRP version 2, the timer values must be in multiples of whole seconds.
PAGE 1013
This time is the gap between an interface coming up and being operational, and VRRP enabling. The seconds range is from 0 to 900. • The default is 0. Set the delay time for VRRP initialization on all the interfaces in the system configured for VRRP. INTERFACE mode vrrp delay reload seconds This time is the gap between system boot up completion and VRRP enabling. The seconds range is from 0 to 900. The default is 0.
PAGE 1014
• show vrrp (Optional) Display the configuration of tracked objects in VRRP groups on a specified interface. EXEC mode or EXEC Privilege mode show running-config interface interface Dell(conf-if-te-1/1/1)#vrrp-group 111 Dell(conf-if-te-1/1/1-vrid-111)#track Tengigabitethernet 1/2/1 The following example shows how to verify tracking using the show conf command.
PAGE 1015
Virtual MAC address: 00:00:5e:00:01:01 Virtual IP address: 1.1.1.100 Authentication: (none) Dell# Tracking states for 2 resource Ids: 2 - Up IPv6 route, 2040::/64, priority-cost 20, 00:02:11 3 - Up IPv6 route, 2050::/64, priority-cost 30, 00:02:11 The following example shows verifying the VRRP configuration on an interface.
PAGE 1016
Figure 159. VRRP for IPv4 Topology Examples of Configuring VRRP for IPv4 and IPv6 The following example shows configuring VRRP for IPv4 Router 2.
PAGE 1017
Figure 160. VRRP for an IPv6 Configuration NOTE: In a VRRP or VRRPv3 group, if two routers come up with the same priority and another router already has MASTER status, the router with master status continues to be MASTER even if one of two routers has a higher IP or IPv6 address. The following example shows configuring VRRP for IPv6 Router 2 and Router 3. Configure a virtual link local (fe80) address for each VRRPv3 group created for an interface.
PAGE 1018
VRRP in a VRF: Non-VLAN Scenario The following example shows how to enable VRRP in a non-VLAN. The following example shows a typical use case in which you create three virtualized overlay networks by configuring three VRFs in two switches. The default gateway to reach the Internet in each VRF is a static route with the next hop being the virtual IP address configured in VRRP. In this scenario, a single VLAN is associated with each VRF.
PAGE 1019
S1(conf-if-te-2/1-vrid-101)#virtual-address 10.10.1.2 S1(conf-if-te-2/1)#no shutdown ! S1(conf)#interface TenGigabitEthernet 2/2 S1(conf-if-te-2/2)#ip vrf forwarding VRF-2 S1(conf-if-te-2/2)#ip address 10.10.1.6/24 S1(conf-if-te-2/2)#vrrp-group 11 % Info: The VRID used by the VRRP group 11 in VRF 2 will be 178. S1(conf-if-te-12/2-vrid-101)#priority 100 S1(conf-if-te-12/2-vrid-101)#virtual-address 10.10.1.
PAGE 1020
VRRP in VRF: Switch-1 VLAN Configuration S1(conf)#ip vrf VRF-1 1 ! S1(conf)#ip vrf VRF-2 2 ! S1(conf)#ip vrf VRF-3 3 ! S1(conf)#interface TenGigabitEthernet 2/4 S1(conf-if-te-2/4)#no ip address S1(conf-if-te-2/4)#switchport S1(conf-if-te-2/4)#no shutdown ! S1(conf-if-te-2/4)#interface vlan 100 S1(conf-if-vl-100)#ip vrf forwarding VRF-1 S1(conf-if-vl-100)#ip address 10.10.1.
PAGE 1021
S2(conf-if-vl-200-vrid-101)#priority 255 S2(conf-if-vl-200-vrid-101)#virtual-address 10.10.1.2 S2(conf-if-vl-200)#no shutdown ! S2(conf-if-te-2/4)#interface vlan 300 S2(conf-if-vl-300)#ip vrf forwarding VRF-3 S2(conf-if-vl-300)#ip address 20.1.1.6/24 S2(conf-if-vl-300)#tagged tengigabitethernet 2/4 S2(conf-if-vl-300)#vrrp-group 15 % Info: The VRID used by the VRRP group 15 in VRF 3 will be 243. S2(conf-if-vl-300-vrid-101)#priority 100 S2(conf-if-vl-300-vrid-101)#virtual-address 20.1.1.
PAGE 1022
• • • • • • • • • Server racks, Rack 1 and Rack 2, are part of data centers DC1 and DC2, respectively. Rack 1 is connected to devices A1 and B1 in a Layer 2 network segment. Rack 2 is connected to devices A2 and B2 in a Layer 2 network segment. A VLT link aggregation group (LAG) is present between A1 and B1 as well as A2 and B2. A1 and B1 are connected to core routers, C1 and D1 with VLT routing enabled. A2 and B2 are connected to core routers, C2 and D2, with VLT routing enabled.
PAGE 1023
interface port-channel 128 channel member ten 1/1/1 channel member ten 1/1/2 no shutdown int ten 1/5/1 port-channel-protocol lacp port-channel 10 mode active no shut int ten 1/4/1 port-channel-protocol lacp port-channel 20 mode active no shut interface port-channel 10 vlt-peer-lag po 10 switchport no shutdown interface port-channel 20 vlt-peer-lag po 20 switchport no shutdown int vlan 100 ip address 100.1.1.1/24 tagged port-channel 10 vrrp-group 10 advertise-interval 60 virtual-ip 100.1.1.
PAGE 1024
no shutdown interface port-channel 20 vlt-peer-lag po 20 switchport no shutdown int vlan 100 ip address 100.1.1.2/24 tagged port-channel 10 vrrp-group 10 advertise-interval 60 virtual-ip 100.1.1.254 priority 100 no shutdown int vlan 200 tagged port-channel 20 no shutdown router ospf 10 network 100.1.1.0/24 area 0 Sample configuration of C2: vlt domain 10 peer-link port-channel 128 back-up destination 10.16.140.
PAGE 1025
no shutdown router ospf 10 network 100.1.1.0/24 area 0 Sample configuration of D2: vlt domain 10 peer-link port-channel 128 back-up destination 10.16.140.
PAGE 1026
66 Standards Compliance This chapter describes standards compliance for Dell Networking products. NOTE: Unless noted, when a standard cited here is listed as supported by the Dell Networking OS, the system also supports predecessor standards. One way to search for predecessor standards is to use the http://tools.ietf.org/ website. Click “Browse and search IETF documents,” enter an RFC number, and inspect the top of the resulting document for obsolescence citations to related RFCs.
PAGE 1027
RFC and I-D Compliance The C9000 series supports the following standards. The standards are grouped by related protocol. General Internet Protocols The following table lists the Dell Networking OS support on the C9000 Series for the general internet protocols. Table 141.
PAGE 1028
RFC# Full Name 5396 Textual Representation of Autonomous System (AS) Numbers draft-ietf-idrbgp4- 20 A Border Gateway Protocol 4 (BGP-4) draft-ietf-idrrestart- 06 Graceful Restart Mechanism for BGP General IPv4 Protocols The following table lists the Dell Networking OS support on the C9000 Series for general IPv4 protocols. Table 143.
PAGE 1029
RFC# Full Name 4291 Internet Protocol Version 6 (IPv6) Addressing Architecture 4443 Internet Control Message Protocol (ICMPv6) for the IPv6 Specification 4861 Neighbor Discovery for IPv6 4862 IPv6 Stateless Address Autoconfiguration 5175 IPv6 Router Advertisement Flags Option Intermediate System to Intermediate System (IS-IS) The following table lists the Dell Networking OS support on the C9000 Series for IS-IS protocol. Table 145.
PAGE 1030
RFC# Full Name 2012 SNMPv2 Management Information Base for the Transmission Control Protocol using SMIv2 2013 SNMPv2 Management Information Base for the User Datagram Protocol using SMIv2 2024 Definitions of Managed Objects for Data Link Switching using SMIv2 2096 IP Forwarding Table MIB 2558 Definitions of Managed Objects for the Synchronous Optical Network/Synchronous Digital Hierarchy (SONET/ SDH) Interface Type 2570 Introduction and Applicability Statements for Internet Standard Management
PAGE 1031
RFC# Full Name draft-grant-tacacs -02 The TACACS+ Protocol draft-ietf-idr-bgp4 - Definitions of Managed Objects for the Fourth Version of the Border Gateway Protocol (BGP-4) using SMIv2 mib-06 draft-ietf-isiswgmib- 16 Management Information Base for Intermediate System to Intermediate System (IS-IS): isisSysObject (top level scalar objects) isisISAdjTable isisISAdjAreaAddrTable isisISAdjIPAddrTable isisISAdjProtSuppTable draft-ietf-netmodinterfaces-cfg-03 Defines a YANG data model for the configurati
PAGE 1032
RFC# Full Name FORCE10-TC-MIB Force10 Textual Convention FORCE10-TRAPALARM-MIB Force10 Trap Alarm MIB Multicast The following table lists the Dell Networking OS support per platform for Multicast protocol. Table 147. Multicast RFC# Full Name S-Series C-Series E-Series TeraScale E-Series ExaScale 1112 Host Extensions for IP Multicasting 7.8.1 7.7.1 √ 8.1.1 2236 Internet Group Management Protocol, Version 2 7.8.1 7.7.1 √ 8.1.1 2710 Multicast Listener Discovery (MLD) for IPv6 √ 8.2.
PAGE 1033
RFC# Full Name 2328 OSPF Version 2 2370 The OSPF Opaque LSA Option 2740 OSPF for IPv6 3623 Graceful OSPF Restart 4222 Prioritized Treatment of Specific OSPF Version 2 Packets and Congestion Avoidance Routing Information Protocol (RIP) The following table lists the Dell Networking OS support on the C9000 Series for RIP protocol. Table 149.
PAGE 1034
67 X.509v3 Dell Networking OS supports X.509v3 standards. Topics: • • • • • • • • • Introduction to X.509v3 certification X.509v3 support in Dell Networking OS Information about installing CA certificates Information about Creating Certificate Signing Requests (CSR) Information about installing trusted certificates Transport layer security (TLS) Online certificate status protocol (OSCP) Verifying certificates Event logging Introduction to X.509v3 certification X.
PAGE 1035
Advantages of X.509v3 certificates Public key authentication is preferred over password-based authentication, although both may be used in conjunction, for various reasons. Public-key authentication provides the following advantages over normal password-based authentication: • • • Public-key authentication avoids the human problems of low-entropy password selection and provides more resistance to brute-force attacks than password-based authentication.
PAGE 1036
The other hosts on the network, such as the SUT switch, syslog server, and OCSP server, generate private keys and create Certificate Signing Requests (CSRs). The hosts then upload the CSRs to the Intermediate CA or make the CSRs available for the Intermediate CA to download. Dell Networking OS generates a CSR using the crypto cert generate request command. The hosts on the network (SUT, syslog, OCSP…) also download and install the CA certificates from the Root and Intermediate CAs.
PAGE 1037
Installing CA certificate To install a CA certificate, perform the following step: Enter the following command in the global configuration mode: crypto ca-cert install {path} Information about Creating Certificate Signing Requests (CSR) Certificate Signing Request (CSR) enables a device to get a X.509v3 certificate from a CA. In order for a device to get a X.509v3 certificate, the device first requests a certificate from a CA through a Certificate Signing Request (CSR).
PAGE 1038
• • • • Email address Validity Length Alternate Name NOTE: The command contains multiple options with the Common Name being a required field and blanks being filled in for unspecified fields. Information about installing trusted certificates Dell Networking OS also enables you to install a trusted certificate. The system can then present this certificate for authentication to clients such as SSH and HTTPS.
PAGE 1039
TLS_ECDH_RSA_WITH_AES_128_CBC_SHA TLS_DH_RSA_WITH_AES_256_CBC_SHA TLS_DH_RSA_WITH_AES_128_CBC_SHA TLS compression is disabled by default. TLS session resumption is also supported to reduce processor and traffic overhead due to public key cryptographic operations and handshake traffic. However, the maximum time allowed for a TLS session to resume without repeating the TLS authentication or handshake process is configurable with a default of 1 hour. You can also disable session resumption.
PAGE 1040
Configuring revocation behavior You can configure the system behavior if an OCSP responder fails. By default, when all the OCSP responders fail to send a response to an OSCP request, the system accepts the certificate and logs the event. However, you can configure the system to reject the certificate in case OCSP responders fail.