Dell Networking C9010 Getting Started Guide Regulatory Model: C9010
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Copyright © 2015 Dell Inc. All rights reserved. This product is protected by U.S. and international copyright and intellectual property laws.
1 About This Guide This document provides information about how to install a C9010 switch with the base configuration in a rack, perform an initial software configuration, and connect to a network. For complete information about C9010 installation and configuration, refer to these documents: Table 1.
2 C9010 Hardware Description The C9010 switch is part of Dell Networking's next-generation LAN solution, providing a scalable switch that offers a path to higher density 10GbE and 40GbE capability. You can deploy the C9010 switch as an access or aggregation/core switch for installations in which a modular switch is preferred. For larger port requirements, you can also connect C1048P port extenders as access devices.
Figure 1. C9010 Chassis — Installed Components with Slot Numbers Unpacking the Switch The switch and its accessories ship in a single container. Before unpacking the switch, inspect the container and immediately report any evidence of damage. Verify that you have received your ordered items. If any item is missing or damaged, contact your Dell Networking representative or reseller for assistance.
The base C9010 configuration package consists of: • One C9010 chassis • One full-width C9000 Series RPM – C9000-RPM-2.56T displays in SW output. – 07KPC3 or 0N90RW is on the HW label. • Three C9000 Series fan modules – C9000-FAN displays in SW output. – 0C94MF is on the HW label. • One AC PSU (110-230V switching) – C9000-PWR-AC displays in SW output. – D3000E-S0 is on the HW label.
airflow, and ventilation. Make sure that the AC power cord can reach the power connector on the front panel of a power supply unit from the power outlet. • Airflow: On the C9010, airflow is from the right to the left side as you face the switch. Hot air is expelled from the left side. Ensure that airflow around the switch and through the side vents is unobstructed and that hot exhaust is not used as air intake on the right side.
3 Installing the Hardware To install the C9010 chassis and power up the switch: 1. Install the C9010 chassis in a 2- or 4-post rack using the rack bar and mounting brackets shipped with the chassis, or use an optional rack mount tray or Dell ReadyRails kit. 2. Secure the chassis ground. 3. Install the fan modules. 4. Install RPMs and line cards. 5. Install the power supplies and power cables. 6. Install the cable management system. 7. Install the QSFP+ and SFP+ optics. 8.
close the front door, re-position and fasten the front rack posts 6.5 inches (165 mm) back towards the rear of the rack to leave space for the brackets. 2. Determine the height at which you want to mount the chassis in the equipment rack. 3. Install the rack bar on the front posts just below the desired height of the bottom of the chassis. The rack bar requires 1 RU below the chassis. Use the rack bar as a guide to mount the chassis.
4. Using a flat-head screwdriver, remove the bracket screws (item 1 in Figure 3) and unscrew the thumb screws to remove the bracket (item 2 in Figure 3) attached to each chassis flange. Figure 3.
5. Use an equipment lift or two people to lift the empty chassis without blanks (item 1 in Figure 4) and align the rack-mount screw holes on each flange of the chassis with the holes in the equipment rack. Rest the chassis on top of the rack bar (or rack tray, if installed). Slide the chassis so that the holes in the side flanges align with the holes in the rack posts. Tighten four rack screws (item 2 in Figure 4) on each chassis flange to attach the chassis to the rack posts.
6. Verify that the chassis is securely installed in the two rack posts and does not sag. To prevent sagging, support the back of the chassis by using a rack mount shelf or Dell ReadyRails as described in Step 3. Figure 5. Chassis Installed in a 2-Post Rack NOTE: To allow for increased airflow, you can remove the rack bar from the front posts.
WARNING: To prevent bodily injury when mounting or servicing this unit in a rack, take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety: • If your chassis is the only unit in the rack, mount it at the bottom of the rack. • When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack.
3. Install the rack bar on the front posts just below the desired height of the bottom of the chassis. The rack bar requires 1 RU below the chassis. Use the rack bar as a guide to mount the chassis. It is not required to support the weight of the chassis; you can remove it when the chassis is securely mounted in the rack. To install the rack bar, first insert two cage nuts (item 2 in Figure 6) into each post at the desired height.
4. To install the chassis, first insert four cage nuts into the front rack posts at the same height as the thumb screws on each chassis flange. On each post, install the lower cage nut in the top post hole 3 RUs above the rack bar; install the upper cage nut in the bottom post hole 5 RUs above the lower cage nut (8 RUs above the rack bar). Refer to Figure 7. Figure 7.
5. Use two people or an equipment lift to align the chassis rack-mount holes with the cage nuts in the front posts (items 1 and 2 in Figure 8). Rest the chassis on top of the rack bar (or rack tray or ReadyRails, if installed). Figure 8.
6. Lift and slide the chassis so that the holes on the chassis flanges touch the holes in the rack posts with cage nuts. Use the rack bar (item 1 in Figure 9) as a guide. First tighten the bottom thumb screw on each flange; then tighten the top thumb screw. Figure 9. Chassis Installed in a 4-Post Rack NOTE: To allow for increased airflow, you can remove the rack bar from the front posts.
• Front rails for the left and right posts of 2- and 4-post racks (items 5 and 6 in Figure 10) • Rear rails that fit into the left and right front rails on 4-post racks (items 7 and 8 in Figure 10) • Two spacers that allow you to secure the chassis flanges flush on the front rack posts (items 9 and 10 in Figure 10) Figure 10. Dell ReadyRails for 2- and 4-Post Racks 1. Left chassis rail 2. Right chassis rail 3. Left ReadyRail bracket for 2-post racks 4.
7. Rear rail that fits into the left front rail 8. Rear rail that fits into the right front rail 9. Left spacer 10. Right spacer Installing ReadyRails: Tool-less Method for a Non-Threaded-Hole Rack To install ReadyRails using a tool-less method in a non-threaded 4-post rack: 1. Attach a Ready rail to the right and left sides of the rack at the desired height. a.
Figure 11.
2. Attach the chassis rails on the right and left sides of the chassis. • Remove the two chassis rails (items 1 and 2 in Figure 10) from the Dell ReadyRails kit. • Align the holes on the right and left chassis rails with the mounting studs at the bottom of each side of the chassis (orange arrows and item 1 in Figure 12). • Press each chassis rail over the studs and slide it backwards (towards the back of the chassis) so that it snaps securely into place (blue arrows and item 2 in Figure 12).
3. Attach a spacer (items 9 and 10 Figure 10) to the back of each chassis flange. The spacers allow the flanges to be attached flush to each rack post. Place each spacer over the four pins at the back of each chassis flange. Then slide each spacer down so that it locks into place and is flush with the flange (Figure 13). Figure 13.
4. Install two cage nuts (item 2 in Figure 14) in each front post at the desired height of the two thumb screws on each flange. Lift the chassis and slide it into the rails installed in the rack (Figure 14). Tighten the thumb screws in the cage nuts to secure the chassis to the rack. Figure 14. Installing the Chassis with ReadyRails in a Non-Threaded-Hole Rack Installing ReadyRails: Tooled Method for a Threaded-Hole Rack To install ReadyRails using a tooled method in a threaded-hole 2- or 4-post rack: 1.
2. Using a flat-tipped screwdriver, remove the bracket subassembly and four pins (items 1, 2, and 4 in Figure 15) from the front and rear of each rail. Pull on each subassembly to fully remove it. Figure 15. Installing Tooled Rails in a Threaded-Hole Rack 3. Attach the front of each rail to the front rack posts using the screws provided with the rack. On a 4-post rack, slide the back end of each rail so that it aligns with the back post holes at the same height.
4. Lift the chassis and slide it into the rails installed in the rack (Figure 16). Tighten the two thumb screws and four rack screws (item 5 in Figure 15) on each flange to secure the chassis to the rack. On a 2-post rack, slide each rail bracket (item 4 in Figure 16) forward to the post. Tighten the two screws (item 3 in Figure 16) to secure the bracket to each post. Figure 16.
To install a rack mount tray in a rack, follow the instructions provided with the tray kit. Decide where you want to mount the switch in the rack. Position the tray at that height and tighten it to the rack posts using the screws shipped with the tray (items 1 to 4 in Figure 17). Figure 17.
2. Attach a grounding cable to the chassis lug by inserting a 6-gauge cable (item 1 in Figure 18). Using a hand-crimping tool (Tyco Electronics 58433-3 or equivalent), crimp the lug (item 2 in Figure 18) so that the cable is held securely. Figure 18. Grounding the Chassis 3. Connect the opposite end of the grounding cable to the nearest grounding post at your site. Installing a Fan Module The C9010 switch requires three fan modules for normal operation.
1. Slide the first fan module into fan slot 0 by pushing the handle (item 1 in Figure 19) forward into the uppermost fan slot (item 2 in Figure 19). 2. Gently push the front of the module until it clicks into place. The fan module should be flush with the chassis. 3. Repeat Steps 1 and 2 to install the second and third fan modules in fan slots 1 and 2. 4. To remove a fan module, press the orange button on the handle and pull out the module. Figure 19.
CAUTION: Unlock the levers before inserting an RPM or line card into the chassis. After you insert the RPM or line card, fully engage the locking mechanism; without the locking mechanism engaged, you can damage a lower line card when you insert it. Installing an RPM Install the fan modules before you install RPMs in a C9010 switch. Figure 20. C9010 Route Processor Module 1. USB-A storage port 2. USB-B console port 3. RJ-45 console port 4. 10/100/1000Base-T RJ-45 management port 5.
1. Open the left and right ejector levers (item 1 in Figure 21) on an RPM by pressing in the orange tab (item 2 in Figure 21) and rotating it to the right so that both levers snap into the open position. Figure 21. Extending the RPM Ejector Levers 2. 30 Hold the card assembly by the metal carrier edges. Avoid touching the printed circuit board and connector pins.
3. The arrow in slot 10 (item 2 in Figure 22; labelled R0 on the chassis) identifies the slot in which you insert the first RPM. Align the card with the guide and gently slide it into the slot by holding the two ejector levers in the fully open position and pushing the card forward. You should feel the backplane connectors on the RPM engage with the chassis backplane. Figure 22. Inserting the First RPM in the Chassis 4.
• To control airflow for adequate system cooling, personal safety, and EMI containment during operation, install a blank in any empty line card slot. Install an operational line card module or a blank in each line card slot. Always replace a line card or blank panel immediately. • The blank panels for RPMs and line cards are different sizes (line card blanks are smaller); be sure to install the correct blank panels in each empty slot. • C9010 line cards are hot-swappable.
Installing a Power Supply The C9010 has four power supply slots at the bottom of the front of the chassis. The C9010 supports only an AC power supply with an IEC 60320 C19 power cable. The power supply is rated as 1450W at 100~120 VAC and 2900W at 200~240 VAC. NOTE: If a power supply fails, Dell Networking recommends that you replace it as soon as possible. C9010 power supply units are hot-swappable. PSU Installation Guidelines • The C9010 requires at least one power supply for normal operation.
Figure 24. Installing the First Power Supply Installing the Cable Management System To organize network cables and minimize the obstruction from cables when you insert, remove, and view chassis components, you can install a cable management system on the front of the chassis. Using the cable management system, you can attach the maximum number of cables in C9010 line card ports.
The cable management system consists of two brackets (items 1 and 2 in Figure 25) and is shipped as part of the C9010 base configuration. Figure 25. Cable Management System NOTE: Dell Networking recommends that you install the cable management system after you install the chassis in a rack and all of the chassis components in the chassis.
To install the cable management system, mount both brackets on the right and left sides of the chassis: 1. Align the openings on the inside of a bracket with the pins (item 1 in Figure 26) and thumb screws on each chassis flange. Figure 26. Installing Cable Management Brackets on the Chassis Flanges 2. 36 Press the bracket forward so that the bracket holes cover the pins and thumb screws on the flanges (item 1 in Figure 27). The bracket locks in place as you press it forward.
Figure 27. Cable Management Brackets Installed on Chassis 3. To open part of a cable bracket, pull one of the latches forward so that it swings down. 4. To remove a cable bracket, push up the blue button located in the center of a bracket to release it. When you cable C9010 ports, be sure not to interfere with the airflow from the ventilation holes on the right and left sides of the chassis. Do not remove the cable management brackets with installed cables.
Powering Up the System Before you supply power to the chassis, Dell Networking recommends that you re-inspect your equipment rack and chassis. Before Powering Up Verify that: • The equipment is properly secured to the rack. • The equipment rack is properly mounted and grounded. • The ambient temperature around the unit (which may be higher than the room temperature) is within the limits specified for the C9010. The supported operational temperature is 32° to 113°F (0°C to 45°C).
After you supply power to the system, the fans operate at medium speed. The green (online) fan module, RPM, and line card LEDs are lit and remain lit as long as the system is receiving power and is operational. When you turn on power supplies and supply power to the chassis, the system performs a series of power-on self tests (POSTs). RPM and line card LEDs blink as the diagnostic programs run. No user interaction is required. You can observe the process on your console terminal.
LED Color / Description • RJ-45 Management Ethernet port: Link LED • (left LED below port) • RJ-45 Management Ethernet port: Activity LED (right LED below port) • • Off — No data link activity Solid green — Link is up and operating at maximum port speed; if autonegotiated, port is operating at 1G. Solid amber — Link is up and operating at lower speed; if auto-negotiated, port is operating at 10/100M. Off — No data link activity Flashing green — Link is up and transmitting/receiving data. Figure 28.
LED Color / Description • Flashing amber — Error condition or reload in progress Figure 29. 1/10GbE SFP+ Port LEDs 1. 24 1/10GbE SFP+ ports with Link/Activity LEDs (up and down arrows indicate port numbers) 2. Module LED Figure 30. 1/10GbE RJ-45 Port LEDs 1. 24 1/10GbE SFP+ ports with Link/Activity Status LEDs (up and down arrows indicate port numbers) 2. Module LED Table 4.
LED Color / Description • • Flashing blue — Beacon LED used to locate the module Flashing amber — Error condition or reload in progress Figure 31. Fan Module LED 1. Fan status LED Table 5. Fan LED LED Color / Description Fan status • • • Solid green — Normal operation; fan module is receiving power. Solid amber — Error condition or reload in progress Off — Fan module is not receiving power. Figure 32. PSU LEDs 1. 42 PSU LED: DC output (on handle) 2.
Table 6. PSU LEDs LED Color / Description PSU: DC output • • • Solid green — Normal DC power output Solid amber — Alarm: PSU is not operational due to a fault condition. Flashing amber — Alarm: Overheating condition PSU: AC input power • Solid green — Normal operation; PSU is receiving power. Switch on the PSU is in the ON (up) position. Flashing green — Alarm: PSU is receiving power, but DC output is disabled. Switch on the PSU is in the OFF (down) position.
4 Configuring the Software After you install the switch in a rack and power it up, you must access the switch to perform the initial software configuration using the command-line interface (CLI) or bare metal provisioning (BMP) after you connect to a network. This chapter describes how to configure the C9010 using the CLI. BMP allows the C9010 to receive a Dell Networking OS image and startup configuration file with initial software settings, including IP address, from a DHCP server.
Figure 33. Console Ports on a Route Processor Module 1. USB-B console port 2. RJ-45 console port Setting RJ-45 Console Access The RJ-45 console port is an asynchronous serial port. If you connect a console to this port, it must support asynchronous transmission. NOTE: Before connecting a console, be sure that a terminal emulation program is already installed on your PC console. 1. Install an RJ-45 copper cable into the console port.
Pin Serial Input/Output 5 GND - 6 RxD Input 7 DSR Input 8 NC (unused) - RJ-45 Console Access with a DB-9 Adapter You can connect to the console through the RJ-45 console port using an RJ-45 to RJ-45 rollover cable and an RJ-45 to DB-9 female DTE adapter (labeled TERMINAL) to a terminal server (for example, a PC). Table 8.
Setting USB-B Console Access For the location of the USB-B console port, refer to C9010 Console Ports. The terminal settings are the same for the USB-B and RJ-45 console port: • 9600 baud rate • No parity • 8 data bits • 1 stop bit • No flow control When you connect a console device to the USB-B port, it becomes the primary connection and sends all messages to the USB-B port. 1. Power on the PC. 2.
• • • • Telnet password Switch IP address Subnet mask (IP netmask) Default gateway (router) Command Modes After you install the hardware and the boot process completes, the console monitor displays the CLI prompt for the EXEC command mode. To configure the switch, you must move linearly through command modes; for example: Prompt CLI Command Mode Dell> EXEC Enter enable to access EXEC Privilege mode. Dell# EXEC Privilege Enter configure to access CONFIGURATION mode.
• enable secret stores the password in the running/startup configuration by using a stronger, MD5 encryption method. Dell Networking recommends using the enable secret password. • Create a password to access EXEC Privilege mode. CONFIGURATION mode Dell(conf)# enable [password | secret] [level level] [encryption-type] password – level is the privilege level and is not required. The default is 15. – encryption-type specifies how a password is entered and is not required.
NOTE: If you are using bare metal provisioning (BMP) to configure the switch, you can connect to a network to locate a DHCP server. BMP allows the C9010 to search the network for a DHCP server from which it can receive a Dell Networking OS image and startup configuration file with initial software settings, including IP address. For more information about BMP, refer to the Dell Networking Open Automation Guide: Configuration and Command Line Reference.
– mask is a subnet mask in /prefix-length format (/ xx). – gateway is the next hop for network traffic originating from the management port. Configuring a Username and Password To access the C9010 remotely, configure a system user name and password. • Configure a user name and password to access the switch remotely.
CONFIGURATION mode Dell(conf)# linecard number port number portmode quad – linecard number port number specifies the line card and 40GbE port to be split. The line card range is 0 to 11; the port range is 0 to 20. – portmode quad configures a 40GbE port to operate in 4x10G mode. For example: Dell(conf)# linecard 0 port 5 portmode quad Creating a VLAN The default VLAN is VLAN 1 (by default) and is stored in the startup configuration. You can configure a different VLAN number as the default VLAN.
VLAN INTERFACE mode Dell(conf-vl-10)# [tagged | untagged] slot/port-range Where slot/port-range specifies a C9010 line card and either a single port number, a port range, or a combination of both for auto-LAG configuration. The range of slot numbers is from 0 to 11. In line card slots 0 to 9, the range of port numbers is from 0 to 23; in RPM slots 10 and 11, the range of port numbers is from 0 to 3.
5 Dell Networking Support The Dell Networking Support site provides a range of documents and tools to assist you with effectively using Dell Networking equipment and mitigating the impact of network outages. Through the support site you can obtain technical information regarding Dell Networking products, access software upgrades and patches, download available management software, and manage your open cases. The Dell Networking support site provides integrated, secure access to these services.
Figure 35.
6 Technical Specifications The following tables describe the technical specifications for the C9010 switch. Table 10. Chassis Physical Design Parameter Specifications Height 13.9 inches (35.26 cm) Width 17.4 inches (44.20 cm) Depth 18.0 inches (45.70 cm) Chassis weight 55 lbs (24.95 kg) empty 152 to 165 lbs (68 to 74.84 kg) fully loaded, depending on the type of line cards installed Table 11.
