Setup Guide

ManualsBrandsDell ManualsAccess PlatformsBrocade G620

53-1004120-01

22 April 2016

Brocade Fabric OS

MIB Reference

Supporting Fabric OS 8.0.1

Summary of content (152 pages)

PAGE 1
53-1004120-01 22 April 2016 Brocade Fabric OS MIB Reference Supporting Fabric OS 8.0.
PAGE 2
© 2016, Brocade Communications Systems, Inc. All Rights Reserved. Brocade, Brocade Assurance, the B-wing symbol, ClearLink, DCX, Fabric OS, HyperEdge, ICX, MLX, MyBrocade, OpenScript, VCS, VDX, Vplane, and Vyatta are registered trademarks, and Fabric Vision is a trademarks of Brocade Communications Systems, Inc., in the United States and/or in other countries. Other brands, products, or service names mentioned may be trademarks of others.
PAGE 3
Contents Preface Document conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix Text formatting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix Command syntax conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . ix Notes, cautions, and warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . x Brocade resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 4
Loading Brocade MIBs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Brocade MIB files. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Standard MIBs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 MIB loading order. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Access Gateway and Brocade MIBs . . . . . . . . . . . . . . . . . . . . . . 10 Firmware upgrades and enabled traps . . . . . . .
PAGE 5
IEEE 802.3 LAG MIB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Fully supported object group. . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Partially supported object group. . . . . . . . . . . . . . . . . . . . . . . . . 31 LLDP MIB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Fully supported object groups. . . . . . . . . . . . . . . . . . . . . . . . . . . 33 LLDP-EXT-DOT1-MIB . . . . . . . . . . . . . . . .
PAGE 6
Chapter 5 High-Availability MIB Objects HA-MIB overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 High-Availability group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 FRU table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 FRU history table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 CP table . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 7
Sensor variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127 Port variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127 Variables for state and status . . . . . . . . . . . . . . . . . . . . . . . . . .127 Variables for statistics and measurement . . . . . . . . . . . . . . . .128 Event variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128 ISL and end device variables . . . . . . . . .
PAGE 8
viii Fabric OS MIB Reference 53-1004120-01
PAGE 9
Preface In this chapter • Document conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • Brocade resources. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • Contacting Brocade Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • Document feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 10
Convention Description bold text Identifies command names, keywords, and command options. italic text Identifies a variable. value In Fibre Channel products, a fixed value provided as input to a command option is printed in plain text, for example, --show WWN. [ ] Syntax components displayed within square brackets are optional. Default responses to system prompts are enclosed in square brackets. {x|y|z} A choice of required parameters is enclosed in curly brackets separated by vertical bars.
PAGE 11
Brocade resources Visit the Brocade website to locate related documentation for your product and additional Brocade resources. You can download additional publications supporting your product at www.brocade.com. Select the Brocade Products tab to locate your product, then click the Brocade product name or image to open the individual product page. The user manuals are available in the resources module at the bottom of the page under the Documentation category.
PAGE 12
• Brocade Supplemental Support augments your existing OEM support contract, providing direct access to Brocade expertise. For more information, contact Brocade or your OEM. • For questions regarding service levels and response times, contact your OEM/Solution Provider. Document feedback To send feedback and report errors in the documentation you can use the feedback form posted with the document or you can e-mail the documentation team.
PAGE 13
About This Document In this chapter • Supported hardware and software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii • What’s new in this document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiv Supported hardware and software In those instances in which procedures or parts of procedures documented here apply to some devices but not to others, this list identifies which devices are supported by Fabric OS 8.0.1.
PAGE 14
What’s new in this document Brocade Gen 6 platform (32-Gbps) Directors • Brocade X6-4 • Brocade X6-8 NOTE Although many different software and hardware configurations are tested and supported by Brocade Communication Systems, Inc for Fabric OS 8.0.1, documenting all possible configurations and scenarios is beyond the scope of this document. Fabric OS support for the Brocade Analytics Monitoring Platform (AMP) device depends on the specific version of the software running on that platform.
PAGE 15
Chapter Understanding Brocade SNMP 1 In this chapter • Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 • Basic SNMP operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 • Understanding MIBs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 • Scalar and Columnar Object Instances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 16
1 Basic SNMP operation SNMP Agent The SNMP agent is a software that resides in the managed devices in the network, and collects data from these devices. Each device hosts an SNMP Agent. The SNMP Agent stores the data, and sends these when requested by an SNMP Manager. In addition, the Agent can asynchronously alert the SNMP Manager about events, by using special PDUs called traps.
PAGE 17
Understanding MIBs TRAP Management Station FIGURE 3 1 Agent SNMP trap The agent can receive queries from one or more management stations and can send traps to up to six management stations. Understanding MIBs The management information base (MIB) is a database of monitored and managed information on a device, in this case a Brocade switch. The MIB structure can be represented by a tree hierarchy.
PAGE 18
1 Access to MIB variables Scalar and Columnar Object Instances Scalar objects have exactly one object instance and identified by appending a single “0” sub-identifier to the object identifier of the scalar object. For example, the swFimwareVersion is a scalar object with OID 1.3.6.1.4.1.1588.2.1.1.1.1.6. To perform “snmpget” to fetch the value of a scalar object, you need to add “0” at the end of the OID, where “0” indicates the instance of that object.
PAGE 19
Traps 1 For more information, refer to “Loading Brocade MIBs” on page 7. Traps An unsolicited message that comes to the management station from the SNMP agent on the device is called a trap. Brocade switches send traps out on UDP port 162 and to any configured port. In order to receive traps, the management station IP address and severity level must be configured on the switch.
PAGE 20
1 Traps HA traps Consider enabling these traps to monitor field-replaceable unit (FRU) status and control processor (CP) status when you have a Brocade director in your environment: • fruStatusChanged: This trap is generated by a FRU status change, such as a switch reboot or disabling or enabling a FRU component such as fandisable, fanenable and so on. • cpStatusChanged: This trap is generated by a change in the status of a CP, including a reboot or firmware download.
PAGE 21
Loading Brocade MIBs 1 FICON traps • • • • • linkRNIDDeviceRegistration: A device registered with the switch. linkRNIDDeviceDeRegistration: A device de-registered with the switch. linkLIRRListenerAdded: A listener for link failure incident is added. linkLIRRListenerRemoved: A listener for link failure incident is removed. linkRLIRFailureIncident: A link failure incident has occurred.
PAGE 22
1 Loading Brocade MIBs • • • • fod.mib HA.mib IbmBladeCenter.mib SW.mib Standard MIBs Distribution of standard MIBs was discontinued starting with Fabric OS 6.4.0. You can download the following MIBs from the http://www.oidview.com/ or http://www.mibdepot.com website: • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 8 BRIDGE-MIB ENTITY-MIB FC-MGMT-MIB FCIP-MGMT-MIB FIBRE-CHANNEL-FE-MIB IANAifType-MIB IEEE 802.1x PAE MIB IEEE 802.
PAGE 23
Loading Brocade MIBs 1 • SNMP-USER-BASED-SM-MIB • SNMP-TARGET-MIB • T11-FC-ZONE-SERVER-MIB (This is a Brocade proprietary MIB. This MIB contains the following traps: t11ZsRequestRejectNotify, t11ZsMergeFailureNotify, t11ZsMergeSuccessNotify, t11ZsDefZoneChangeNotify, and t11ZsActivateNotify.) MIB loading order Many MIBs use definitions defined in other MIBs. These definitions are listed in the IMPORTS section near the top of the MIB.
PAGE 24
1 Loading Brocade MIBs TABLE 1 Brocade SNMP MIB dependencies (Continued) MIB Name Dependencies ENTITY-MIB SNMPv2-SMI SNMPv2-TC SNMPv2-CONF SNMP-FRAMEWORK-MIB SW.mib SNMPv2-TC SNMPv2-SMI Brocade-TC Brocade-REG-MIB FCMGMT-MIB brcdfcip.mib SNMPv2-SMI Brocade-REG-MIB SNMPv2-TC INET-ADDRESS-MIB IF-MIB SNMPv2-CONF faext.mib SNMPv2-TC SNMPv2-SMI SW-MIB FCMGMT-MIB FICON.mib SNMPv2-SMI SNMPv2-TC Brocade-REG-MIB HA.
PAGE 25
Firmware upgrades and enabled traps TABLE 2 1 Access Gateway MIB support (Continued) MIB name Description SW-MIB Disabled in Access Gateway because the conventions are specific to fabric switches. The swConnUnitPortExtensionTable is supported in Access Gateway mode. In Fabric OS 7.0.
PAGE 26
1 Support for Virtual Fabric Support for Virtual Fabric Virtual Fabric is supported in Fabric OS v6.2.0 and later releases. NOTE An SNMPv3 must be used when you want to manage a Virtual Fabric. When an SNMPv3 request arrives with a particular user name, it executes in the home Virtual Fabric. From the SNMP manager, all SNMPv3 requests have a home Virtual Fabric that is specified in the contextName field.
PAGE 27
Customized traps 1 Attributes that are common across the logical switches belong to the chassis level. These attributes are accessible to users having the chassis-role permission. When a chassis table is queried, the context is set to chassis context, if the user has the chassis-role permission. The context is switched back to the original context after the operation is performed. Customized traps This section is only applicable for OEM customers. FOS 7.0.0 and 7.0.
PAGE 28
1 14 References Fabric OS MIB Reference 53-1004120-01
PAGE 29
Chapter 2 Supported Standard MIBs In this chapter • RFC 1213: MIB-II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • RFC 1757: Remote Network Monitoring Management Information Base . . • RFC 4133: Entity MIB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • Bridge-MIB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • P-Bridge MIB . . . . . . . . . . . . . . . . . .
PAGE 30
2 RFC 1213: MIB-II RFC 1213: MIB-II Fully supported/deprecated object groups The following groups from RFC 1213 are either fully supported or deprecated. Object group name OID Supported? system 1.3.6.1.2.1.1 Yes NOTE: All systems must implement the System group. If an agent is not configured to have a value for any of the System group variables, a string of length 0 is returned. at 1.3.6.1.2.1.3 No NOTE: Implementation of the Address Translation group is mandatory for all systems.
PAGE 31
RFC 1213: MIB-II 2 Partially supported object groups The following groups from RFC 1213 are partially supported. Interfaces group Implementation of the Interfaces group is mandatory for all systems. To support FCIP tunneling, entries are created in the ifTable for each WAN interface (GbE port), each FC port, and each FCIP tunnel (transport interface). TABLE 3 Fabric OS MIB Reference 53-1004120-01 Object OID Supported? ifNumber 1.3.6.1.2.1.2.1 Yes ifTable 1.3.6.1.2.1.2.2 Yes ifEntry 1.3.6.1.
PAGE 32
2 RFC 1213: MIB-II IP group Implementation of the IP group is mandatory for all systems. TABLE 4 18 Object OID Supported? ipForwarding 1.3.6.1.2.1.4.1 Yes ipDefaultTTL 1.3.6.1.2.1.4.2 Yes ipInReceives 1.3.6.1.2.1.4.3 Yes ipInHdrErrors 1.3.6.1.2.1.4.4 Yes ipInAddrErrors 1.3.6.1.2.1.4.5 Yes ipForwDatagrams 1.3.6.1.2.1.4.6 Yes ipInUnknownProtos 1.3.6.1.2.1.4.7 Yes ipInDiscards 1.3.6.1.2.1.4.8 Yes ipInDelivers 1.3.6.1.2.1.4.9 Yes ipOutRequests 1.3.6.1.2.1.4.
PAGE 33
RFC 1213: MIB-II TABLE 4 2 (Continued) Object OID Supported? ipRouteMetric4 1.3.6.1.2.1.4.21.1.6 Yes ipRouteNextHop 1.3.6.1.2.1.4.21.1.7 Yes ipRouteType 1.3.6.1.2.1.4.21.1.8 Yes ipRouteProto 1.3.6.1.2.1.4.21.1.9 Yes ipRouteAge 1.3.6.1.2.1.4.21.1.10 No ipRouteMask 1.3.6.1.2.1.4.21.1.11 Yes ipRouteMetric5 1.3.6.1.2.1.4.21.1.12 Yes ipRouteInfo 1.3.6.1.2.1.4.21.1.13 Yes ipNetToMediaTable 1.3.6.1.2.1.4.22 Yes ipNetToMediaEntry 1.3.6.1.2.1.4.22.1 Yes ipNetToMediaIfIndex 1.3.
PAGE 34
2 RFC 1757: Remote Network Monitoring Management Information Base TABLE 5 Object OID Supported? ifXTable 1.3.6.1.2.1.31.1.1 Yes ifXentry 1.3.6.1.2.1.31.1.1.1 Yes ifName 1.3.6.1.2.1.31.1.1.1.1 Yes ifInMulticastPkts 1.3.6.1.2.1.31.1.1.1.2 No ifInBroadcastPkts 1.3.6.1.2.1.31.1.1.1.3 No ifOutMulticastPkts 1.3.6.1.2.1.31.1.1.1.4 No ifOutBroadcastPkts 1.3.6.1.2.1.31.1.1.1.5 No NOTE: This object is supported only on FCIP interfaces. ifHCInOctets 1.3.6.1.2.1.31.1.1.1.
PAGE 35
RFC 4133: Entity MIB Object group name OID Supported? history 1.3.6.1.2.1.16.2 Yes alarm 1.3.6.1.2.1.16.3 Yes event 1.3.6.1.2.1.16.9 Yes 2 RFC 4133: Entity MIB Entity MIB is the module for representing multiple logical entities supported by a single SNMP agent. Textual conventions for Entity MIB PhysicalIndex Arbitrary value that uniquely identifies the physical entity. Value should be a small positive integer; index values for different physical entities are not necessarily contiguous.
PAGE 36
2 RFC 4133: Entity MIB TABLE 6 Possible values for PhysicalClass (Continued) Values Description container (5) The physical entity class is capable of containing one ore more removable physical entities, possibly of different types (such as a chassis slot or daughter-card holder). For example, each (empty or full) slot in a chassis is modeled as a container.
PAGE 37
RFC 4133: Entity MIB 2 Fully supported object group The following groups from RFC 4133 are fully supported. Physical entity group TABLE 7 Fabric OS MIB Reference 53-1004120-01 Object group name OID Supported? entityPhysical 1.3.6.1.2.1.47.1.1 Yes entPhysicalTable 1.3.6.1.2.1.47.1.1.1 Yes entPhysicalEntry 1.3.6.1.2.1.47.1.1.1.1 Yes entPhysicalIndex 1.3.6.1.2.1.47.1.1.1.1.1 Yes entPhysicalDescr 1.3.6.1.2.1.47.1.1.1.1.2 Yes entPhysicalVendorType 1.3.6.1.2.1.47.1.1.1.1.
PAGE 38
2 RFC 4133: Entity MIB Chassis: one entry Container: one entry for each FRU slot Power supply if the PS is not a FRU, it will be directly below the chassis FIGURE 5 Module if the Module is not a FRU, it will be directly below the chassis Fan If the Fan is not a FRU, it will be directly below the chassis entPhysicalTable containment hierarchy (entPhysicalContainsTable) Unsupported object groups The following groups from RFC 4133 are not supported. Object group name OID Supported? entLogical 1.3.
PAGE 39
Bridge-MIB 2 Bridge-MIB The Bridge MIB module for managing devices that support IEEE 802.1D. Fully supported object groups The following groups from LLDP-EXT-DOT1-MIB are fully supported. Object group name OID Supported dot1dBase 1.3.6.1.2.1.17.1 Yes This contains the objects that are applicable to all types of bridges (support only for default VLAN). dot1dStp 1.3.6.1.2.1.17.2 Yes This contains objects that denote the bridge’s state with respect to the Spanning Tree Protocol.
PAGE 40
2 Q-Bridge MIB • • • • • dot1dUserPriorityRegenTable dot1dTrafficClassTable dot1dPortOutboundAccessPriorityTable dot1dPortGarpTable dot1dPortGmrpTable Fully supported object groups The following groups from P-Bridge MIB are fully supported. Object group name OID Supported dot1dBase 1.3.6.1.2.1.17.1 Yes dot1dExtBase 1.3.6.1.2.1.17.6.1.1 Yes dot1dPortPriorityTable 1.3.6.1.2.1.17.6.1.2.
PAGE 41
FCIP MIB Objects 2 Fully supported object groups The following groups from RSTP MIB are fully supported. Object group name OID Supported dot1dStpVersion 1.3.6.1.2.1.17.2.16 Yes dot1dStpTxHoldCount 1.3.6.1.2.1.17.2.17 Yes dot1dStpExtPortTable 1.3.6.1.2.1.17.2.19 Yes FCIP MIB Objects You can refer to RFC 4044 for description of the entire MIB. Fully supported object groups The following groups from FCIP MIB are fully supported. Object group name OID Supported? fcipEntityInstanceTable 1.3.6.
PAGE 42
2 FIBRE-CHANNEL-FE-MIB (MIB-II branch) Object OID Supported? fcipExtendedLinkRawBytes 1.3.6.1.4.1.1588.4.1.1.6 Yes fcipExtendedLinkCompressedBytes 1.3.6.1.4.1.1588.4.1.1.7 Yes fcipExtendedLinkConnectedCount 1.3.6.1.4.1.1588.4.1.1.8 Yes fcipExtendedLinkRtxRtxTO 1.3.6.1.4.1.1588.4.1.1.9 No fcipExtendedLinkRtxDupAck 1.3.6.1.4.1.1588.4.1.1.10 No fcipExtendedLinkDupAck 1.3.6.1.4.1.1588.4.1.1.11 Yes fcipExtendedLinkRtt 1.3.6.1.4.1.1588.4.1.1.12 Yes fcipExtendedLinkOoo 1.3.6.1.4.1.1588.4.
PAGE 43
FIBRE-CHANNEL-FE-MIB (MIB-II branch) TABLE 8 2 FE MIBs and supported Fabric OS versions Fabric OS version FIBRE-CHANNEL-FE-MIB (MIB-II branch) FCFABRIC-ELEMENT-MIB (experimental branch) 8.0.1 Yes No 8.0.0 Yes No 7.4.0 Yes No 7.3.0 Yes No 7.2.0 Yes No 7.1.0 Yes No 7.0.0 Yes No 6.4.1_fcoe Yes No 6.4.0 Yes No 6.3.0 Yes No 6.2.0 Yes No 6.1.2_CEE Yes No 6.1.0 Yes No 6.0.0 Yes No 5.x Yes No 4.x Yes No 3.1.x Yes No 3.0.x Yes Yes 2.6.
PAGE 44
2 IEEE 802.1x PAE MIB Object group name OID Supported? fcFeConfig group 1.3.6.1.2.1.75.1.1 Yes This group consists of scalar objects and tables. It contains the configuration and service parameters of the fabric element and the Fx_Ports. The group represents a set of parameters associated with the fabric element or an Fx_Port to support its Nx_Ports. fcFeStatus group 1.3.6.1.2.1.75.1.
PAGE 45
IEEE 802.3 LAG MIB 2 IEEE 802.3 LAG MIB Fully supported object group The following group from IEEE 802.3 LAG MIB is fully supported. Object group name OID Supported dot3adAggTable 1.2.840.10006.300.43.1.1.1 Yes Partially supported object group The following group from IEEE 802.3 LAG MIB is partially supported. Aggregator port group Fabric OS MIB Reference 53-1004120-01 Object OID Supported? dot3adAggPortTable 1.2.840.10006.300.43.1.2.1 Yes dot3adAggPortEntry 1.2.840.10006.300.43.1.2.1.
PAGE 46
2 LLDP MIB Object OID Supported? dot3adAggPortPartnerAdminState 1.2.840.10006.300.43.1.2.1.1.22 Yes dot3adAggPortPartnerOperState 1.2.840.10006.300.43.1.2.1.1.23 Yes dot3adAggPortAggregateOrIndividual 1.2.840.10006.300.43.1.2.1.1.24 Yes dot3adAggPortStatsTable 1.2.840.10006.300.43.1.2.2 Yes dot3adAggPortStatsEntry 1.2.840.10006.300.43.1.2.2.1 Yes dot3adAggPortStatsLACPDUsRx 1.2.840.10006.300.43.1.2.2.1.1 Yes dot3adAggPortStatsMarkerPDUsRx 1.2.840.10006.300.43.1.2.2.1.
PAGE 47
LLDP-EXT-DOT1-MIB 2 NOTE LLDP notifications are not supported. Fully supported object groups The following groups from LLDP MIB are fully supported. Object group name OID Supported? lldpConfiguration 1.0.8802.1.1.2.1.1 Yes lldpStatistics 1.0.8802.1.1.2.1.2 Yes lldpLocalSystemData 1.0.8802.1.1.2.1.3 Yes lldpRemoteSystemsData 1.0.8802.1.1.2.1.4 Yes LLDP-EXT-DOT1-MIB The LLDP Management Information Base extension module for IEEE 802.1 organizationally-defined discovery information.
PAGE 48
2 LLDP-EXT-DOT3-MIB lldpXdot3 local data group Object OID Supported? lldpXdot3LocalData 1.0.8802.1.1.2.1.5.4623.1.2 Yes lldpXdot3LocPortTable 1.0.8802.1.1.2.1.5.4623.1.2.1 Yes lldpXdot3LocPortEntry 1.0.8802.1.1.2.1.5.4623.1.2.1.1 Yes lldpXdot3LocPortAutoNegSupported 1.0.8802.1.1.2.1.5.4623.1.2.1.1.1 Yes lldpXdot3LocPortAutoNegEnabled 1.0.8802.1.1.2.1.5.4623.1.2.1.1.2 Yes lldpXdot3LocPortAutoNegAdvertisedCap 1.0.8802.1.1.2.1.5.4623.1.2.1.1.3 Yes lldpXdot3LocPortOperMauType 1.0.8802.1.
PAGE 49
SNMPv2 MIB 2 SNMPv2 MIB Fully supported object groups The following groups from SNMPv2 MIB are fully supported. Object group name OID Supported? snmpTargetAddrTable 1.3.6.1.6.3.12.1.2 Yes snmpTargetParamsTable 1.3.6.1.6.3.12.1.3 Yes snmpCommunityTable 1.3.6.1.6.3.18.1.1 Yes USM MIB Objects Fully supported object groups The following groups from USM MIB are fully supported. Fabric OS MIB Reference 53-1004120-01 Object group name OID Supported usmStats 1.3.6.1.6.3.15.1.1 Yes usmUser 1.
PAGE 50
2 36 USM MIB Objects Fabric OS MIB Reference 53-1004120-01
PAGE 51
Chapter 3 SW-MIB Objects In this chapter • SW-MIB overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • sw traps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • Switch system group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • Switch Fabric group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 52
3 SW-MIB overview Textual conventions for SW-MIB Table 9 lists the textual conventions used for SW-MIB. TABLE 9 SW-MIB textual conventions Type definition Value Description FcWwn Octet String of size 8 The World Wide Name (WWN) of Brocade-specific products and ports. SwDomainIndex Integer of size 1 to 239 Fibre Channel domain ID of the switch. SwNbIndex Integer of size 1 to 2048 Index of the neighbor inter-switch link (ISL) entry.
PAGE 53
SW-MIB overview TABLE 9 3 SW-MIB textual conventions (Continued) Type definition Value Description SwFwLevels Integer Threshold or Action levels: 1 swFwReserved (Not supported) 2 swFwDefault 3 swFwCustom Commands: • portthconfig To set port thresholds • thconfig To set other thresholds • sysmonitor --config To set ENV/RES class ENV- Environment, RES - Resource Fabric OS MIB Reference 53-1004120-01 39
PAGE 54
3 SW-MIB overview TABLE 9 SW-MIB textual conventions (Continued) Type definition Value Description SwFwClassesAreas Integer Index of Fabric Watch classes and areas where thresholds can be monitored: Environment class: 1 swFwEnvTemp 2 swFwEnvFan (Not supported) 3 swFwEnvPS (Not supported) SFP class: 4 swFwTransceiverTemp 5 swFwTransceiverRxp 6 swFwTransceiverTxp 7 swFwTransceiverCurrent 57 swFwTransceiverVoltage Port class: 8 swFwPortLink 9 swFwPortSync 10 swFwPortSignal 11 swFwPortPe 12 swFwPortWor
PAGE 55
sw traps TABLE 9 3 SW-MIB textual conventions (Continued) Type definition Value Description EportUtil and EportPktl are the MIB defines used for VE ports for Legacy FCIP (FR4-18i router blade/Brocade 7500),while VEPortUtil and VEPortPktlLoss are used for VE ports for Brocade 7800 Extension Switch/FX8-24 DCX Extension Blade. In the index swFwEnvTemp, Env refers to Environment class and Temp refers to the area Temperature.
PAGE 56
3 sw traps TABLE 10 SW-MIB traps Trap name Commands to configure “swFault” on page 43 (not supported) N.A. “swSensorScn” on page 43 N.A. “swFCPortScn” on page 43 Always on “swEventTrap” on page 44 For more information, refer to the snmpConfig command in the Fabric OS Command Reference. “swTrackChangesTrap” on page 44 Fabric OS Command: trackChangesSet and trackChangesShow “swIPv6ChangeTrap” on page 44 For more information, refer to the snmpConfig command in the Fabric OS Command Reference.
PAGE 57
sw traps 3 TABLE 11 Trap name and OID Variables Description swFault 1.3.6.1.4.1.1588.2.1.1.1.0.1 swDiagResult swSsn This trap is no longer generated. A swFault is generated whenever the diagnostics detect a fault with the switch. #TYPE #SUMMARY #ARGUMENTS #SEVERITY #TIMEINDEX #STATE swSensorScn 1.3.6.1.4.1.1588.2.1.1.1.0.2 swSensorStatus swSensorIndex swSensorType swSensorValue swSensorInfo swSsn Switch is faulty.
PAGE 58
3 sw traps TABLE 11 Trap name and OID Variables Description swEventTrap 1.3.6.1.4.1.1588.2.1.1.1.0.4 swEventIndex swEventTimeInfo swEventLevel swEventRepeatCount swEventDescr swSsn swVfId This trap is generated when an event occurs with a level that is at or below swEventTrapLevel. #TYPE #SUMMARY A firmware event has been logged.
PAGE 59
sw traps 3 TABLE 11 Trap name and OID Variables Description swPmgrEventTrap 1.3.6.1.4.1.1588.2.1.1.1.0.8 swPmgrEventType swPmgrEventTime swPmgrEventDescr swSsn swVfId This trap is generated when any partition manager change happens. This trap is generated when: • Logical switch is created or deleted. • Port is moved between logical switches. • Switch FID changes. • When any logical switch is changed to base switch. • VF is enabled or disabled. swFabricReconfigTrap 1.3.6.1.4.1.1588.2.1.1.1.0.
PAGE 60
3 Switch system group TABLE 11 Trap name and OID Variables Description swBrcdGenericTrap 1.3.6.1.4.1.1588.2.1.1.1.0.14 swBrcdTrapBitMask swBrcdBitObjVal swVfId This trap is sent for one of the following events: • fabric change • device change • FAPWWN change • FDMI events • Routing policy change • Diagnostics port configuration change • Polling status • Dynamic port name change • Dynamic port name feature enable/disable event This trap is enabled by default. NOTE: This trap is for internal use.
PAGE 61
Switch system group 3 TABLE 12 Object and OID Access Description swBootDate 1.3.6.1.4.1.1588.2.1.1.1.1.2 Read only The date and time when the system last booted. The return string displays using the following format: ddd MMM DD hh:mm:ss yyyy Where: ddd = day MMM = month DD = date hh = hour mm = minute ss = seconds yyyy = year For example: Thu Aug 17 15:16:09 2000 swFWLastUpdated 1.3.6.1.4.1.1588.2.1.1.1.1.3 Read only The date and time when the firmware was last loaded to the switch.
PAGE 62
3 Switch system group TABLE 12 Object and OID Access Description swBootPromLastUpdated 1.3.6.1.4.1.1588.2.1.1.1.1.5 Read only The date and time when the BootPROM was last updated. The return string displays using the following format: ddd MMM DD hh:mm:ss yyyy Where: ddd = day MMM = month DD = date hh = hour mm = minute ss = seconds yyyy = year For example: Thu Aug 17 15:16:09 2000 48 swFirmwareVersion 1.3.6.1.4.1.1588.2.1.1.1.1.6 Read only The current version of the firmware.
PAGE 63
Switch system group 3 TABLE 12 Object and OID Access Description swTelnetShellAdmStatus 1.3.6.1.4.1.1588.2.1.1.1.1.9 Read-write The desired administrative status of the Telnet shell. Setting this value to 1 (terminated), deletes the current Telnet shell task. When this variable instance is read, it reports the value last set through SNMP. This OID is supported in Fabric OS 2.x through 3.x. This OID is not supported in Fabric OS 4.0 through 4.2. This OID is supported in Fabric OS 4.
PAGE 64
3 Switch system group TABLE 12 50 Object and OID Access Description swFlashDLPassword 1.3.6.1.4.1.1588.2.1.1.1.1.16 Read-write The password to be used for FTP transfer of files in the download or upload operation. swBeaconOperStatus 1.3.6.1.4.1.1588.2.1.1.1.1.18 Read only The current operational status of the switch beacon. Possible values are: • on (1) - The LEDs on the front panel of the switch run alternately from left to right and right to left. The color is yellow.
PAGE 65
Switch system group 3 TABLE 12 Object and OID Access Description swSensorStatus 1.3.6.1.4.1.1588.2.1.1.1.1.22. 1.3 Read only The current status of the sensor. Possible values are: • unknown (1) • faulty (2) • below-min (3) - The sensor value is below the minimal threshold. • nominal (4) • above-max (5) - The sensor value is above the maximum threshold. • absent (6) - The sensor is missing. For Temperature, valid values include 3 (below-min), 4 (nominal), and 5 (above-max).
PAGE 66
3 Switch system group TABLE 12 52 Object and OID Access Description swFCIPAddress 1.3.6.1.4.1.1588.2.1.1.1.1.27 Read only The IP address of the FC interface of this switch. swFCIPMask 1.3.6.1.4.1.1588.2.1.1.1.1.28 Read only The IP mask of the FC interface of this switch. swIPv6Address 1.3.6.1.4.1.1588.2.1.1.1.1.29 Not accessible The IPv6 address. This object is not accessible. swIPv6Status 1.3.6.1.4.1.1588.2.1.1.1.1.30 Not accessible The current status of the IPv6 address.
PAGE 67
Switch system group 3 TABLE 12 Object and OID Access swBrcdBitObjVal 1.3.6.1.4.1.1588.2.1.1.1.1.37 Not accessible The object contains object value for each change mentioned in the swBrcdGenericTrap. It will be empty for the events which do not have any value. swIODState 1.3.6.1.4.1.1588.2.1.1.1.1.38 Read only TABLE 13 The object represents the IOD feature state.
PAGE 68
3 Switch Fabric group TABLE 14 Blade table (Continued) Model Temp sensors FS8-18 5 sensors FX8-24 3 sensors FCOE10-24 5 sensors FC8-16 5 sensors FC8-32 7 sensors FC8-48 7 sensors FC8-64 8 sensors FC8-32E 7 sensors FC8-48E 7 sensors CP8 4 sensors Core8 4 sensors CR4S-8 4 sensors Switch Fabric group TABLE 15 54 Object and OID Access Description swFabric 1.3.6.1.4.1.1588.2.1.1.1 .2 Not accessible The OID sub-tree for the switch Fabric group. swDomainID 1.3.6.1.4.1.1588.2.
PAGE 69
Switch Fabric group 3 TABLE 15 Fabric OS MIB Reference 53-1004120-01 Object and OID Access Description swNbMyPort 1.3.6.1.4.1.1588.2.1.1.1 .2.9.1.2 Read only This is the port that has an ISL to another switch. This value is the same as the physical port number of the local switch +1. swNbRemDomain 1.3.6.1.4.1.1588.2.1.1.1 .2.9.1.3 Read only This is the Fibre Channel domain on the other end of the ISL. This is the domain ID of the remote switch.Valid values are 1 through 239 as defined by FCS-SW.
PAGE 70
3 Switch agent configuration group TABLE 15 Object and OID Access Description swPmgrEventTime 1.3.6.1.4.1.1588.2.1.1.1 .2.13 Not accessible This object identifies the date and time when any events mentioned in swPmgrEventType occur, in textual format. swPmgrEventDescr 1.3.6.1.4.1.1588.2.1.1.1 .2.14 Not accessible This object identifies the textual description of the events mentioned in swPmgrEventType. swVfId 1.3.6.1.4.1.1588.2.1.1.1 .2.15 Read only The virtual Fabric ID of the switch.
PAGE 71
Fibre Channel port group 3 TABLE 16 Object and OID Access Description swAgtCmtyStr 1.3.6.1.4.1.1588.2.1.1.1 .4.11.1.2 Read-write This is a community string supported by the agent. If a new value is set successfully, it takes effect immediately. Default values for communities are as follows: • 1 (Secret Code) • 2 (OrigEquipMfr) • 3 (private) • 4 (public) • 5 (common) • 6 (FibreChannel) Community strings 1-3 are read-write and strings 4-6 are read only.
PAGE 72
3 Fibre Channel port group TABLE 17 58 Object and OID Access Description swFCPortEntry 1.3.6.1.4.1.1588.2.1.1.1.6.2 .1 Not accessible An entry containing the configuration and service parameters of the switch port. swFCPortIndex 1.3.6.1.4.1.1588.2.1.1.1.6.2 .1.1 Read only The switch port index. The value of swFCPortIndex is 1 higher than the actual port index. For example, a swFCPortIndex of 1 corresponds to the actual port index of 0. swFCPortType 1.3.6.1.4.1.1588.2.1.1.1.6.2 .1.
PAGE 73
Fibre Channel port group 3 TABLE 17 Object and OID Access Description swFCPortAdmStatus 1.3.6.1.4.1.1588.2.1.1.1.6.2 .1.5 Read-write The desired state of the port. A management station might place the port in a desired state by setting this object accordingly. Based on the port status, this OID returns one of the following: • Online - When queried port is online. • Offline - When queried port is offline. • Faulty - When port is in faulty state.
PAGE 74
3 Fibre Channel port group TABLE 17 60 Object and OID Access Description swFCPortRxMcasts 1.3.6.1.4.1.1588.2.1.1.1.6.2 .1.18 Read only Counts the number of multicast frames that the port has received. swFCPortTooManyRdys 1.3.6.1.4.1.1588.2.1.1.1.6.2 .1.19 Read only Counts the number of times that RDYs exceeds the frames received. swFCPortNoTxCredits 1.3.6.1.4.1.1588.2.1.1.1.6.2 .1.20 Read only Counts the number of times that the transmit credit has reached 0. swFCPortRxEncInFrs 1.3.6.1.4.1.
PAGE 75
Name Server database group 3 TABLE 17 Object and OID Access Description swFCPortLipLastAlpa 1.3.6.1.4.1.1588.2.1.1.1.6.2 .1.33 Read only Indicates the physical address (AL_PA) of the loop device that initiated the last loop initialization. swFCPortWwn 1.3.6.1.4.1.1588.2.1.1.1.6.2 .1.34 Read only The WWN of the Fibre Channel port. The contents of an instance are in IEEE extended format, as specified in FC-PH. swFCPortSpeed 1.3.6.1.4.1.1588.2.1.1.1.6.2 .1.
PAGE 76
3 Name Server database group TABLE 18 62 Object and OID Access Description swNsLocalTable 1.3.6.1.4.1.1588.2.1.1.1.7.2 Not accessible The table of local Name Server entries. swNsLocalEntry 1.3.6.1.4.1.1588.2.1.1.1.7.2.1 Not accessible An entry from the local Name Server database. swNsEntryIndex 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.1 Read only The index of the Name Server database entry. swNsPortID 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.2 Read only The Fibre Channel port address ID of the entry.
PAGE 77
Event group 3 TABLE 18 Object and OID Access Description swNsCos Read only 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.10 The class of services supported by the port.
PAGE 78
3 Fabric Watch group TABLE 19 Object and OID Access Description swEventTable 1.3.6.1.4.1.1588.2.1.1.1 .8.5 Not accessible The table of event entries. The events will be received from the CHASSIS and the created logical switches. Only external RASlog messages are supported. These external messages are documented in the Fabric OS Message Reference. swEventEntry 1.3.6.1.4.1.1588.2.1.1.1 .8.5.1 Not accessible An entry of the event table. swEventIndex 1.3.6.1.4.1.1588.2.1.1.1 .8.5.1.
PAGE 79
End device group 3 End device group TABLE 20 Object and OID Access Description swEndDevice 1.3.6.1.4.1.1588.2.1.1.1.21 Not accessible The OID sub-tree for end device group. swEndDeviceRlsTable 1.3.6.1.4.1.1588.2.1.1.1.21.1 Not accessible The table of RLS for individual end devices. swEndDeviceRlsEntry 1.3.6.1.4.1.1588.2.1.1.1.21.1.1 Not accessible An entry of an individual end devices' RLS. Since Brocade switches start with port # 0, the SNMP port # should be physical port # plus 1.
PAGE 80
3 Bloom performance monitor group TABLE 21 Object and OID Access Description swGroupEntry 1.3.6.1.4.1.1588.2.1.1.1.22.1. 1 Not accessible An entry of table of groups. swGroupIndex 1.3.6.1.4.1.1588.2.1.1.1.22.1. 1.1 Read only This object is the group index, starting from 1. swGroupName 1.3.6.1.4.1.1588.2.1.1.1.22.1. 1.2 Read only This object identifies the name of the group. swGroupType 1.3.6.1.4.1.1588.2.1.1.1.22.1. 1.3 Read only swGroupMemTable 1.3.6.1.4.1.1588.2.1.1.1.22.
PAGE 81
Trunking group 3 Trunking group TABLE 22 Fabric OS MIB Reference 53-1004120-01 Object and OID Access Description swTrunk 1.3.6.1.4.1.1588.2.1.1.1.24 Not accessible The OID sub-tree for swTrunk group. swSwitchTrunkable 1.3.6.1.4.1.1588.2.1.1.1.24.1 Not accessible This object indicates whether the switch supports the trunking feature or not: • no (0) • yes (8) swTrunkTable 1.3.6.1.4.1.1588.2.1.1.1.24.2 Not accessible This object displays trunking information for the switch. swTrunkEntry 1.3.6.
PAGE 82
3 Toptalker group TABLE 22 Object and OID Access Description swTrunkGrpTx 1.3.6.1.4.1.1588.2.1.1.1.24.3. 1.3 Read only Gives the aggregate value of the transmitted words from this trunk group. swTrunkGrpRx 1.3.6.1.4.1.1588.2.1.1.1.24.3. 1.4 Read only NOTE: The syntax for this MIB variable is an OCTET STRING. The output is shown in hexadecimal value. The value of swTrunkGrpTx is the 4-byte word transmitted in the TrunkGrp port.
PAGE 83
Switch connectivity unit port statistics extension table 3 TABLE 23 Object and OID Access Description swCpuPollingInterval 1.3.6.1.4.1.1588.2.1.1.1. 26.4 Read only The time after which the next CPU usage value will be recorded. swCpuAction 1.3.6.1.4.1.1588.2.1.1.1. 26.5 Read only The action to be taken if the CPU usage exceeds the specified threshold limit. swMemUsage 1.3.6.1.4.1.1588.2.1.1.1. 26.6 Read only The system's memory usage. swMemNoOfRetries 1.3.6.1.4.1.1588.2.1.1.1. 26.
PAGE 84
3 Switch connectivity unit port statistics extension table TABLE 24 70 Object and OID Access Description swConnUnitCRCWithBadE OF 1.3.6.1.4.1.1588.2.1.1.1. 27.1.1 Read only The number of frames with CRC error having Bad EOF. swConnUnitZeroTenancy 1.3.6.1.4.1.1588.2.1.1.1. 27.1.2 Read only This counter is incremented when the FL_port acquires the loop, but does not transmit a frame. swConnUnitFLNumOfTena ncy 1.3.6.1.4.1.1588.2.1.1.1. 27.1.
PAGE 85
Switch connectivity unit port statistics extension table 3 TABLE 24 Fabric OS MIB Reference 53-1004120-01 Object and OID Access Description swConnUnitBadEOF 1.3.6.1.4.1.1588.2.1.1.1. 27.1.15 Read only The number of frames with bad EOF. swConnUnitLCRX 1.3.6.1.4.1.1588.2.1.1.1. 27.1.16 Read only The number of link control frames received. swConnUnitRDYPriority 1.3.6.1.4.1.1588.2.1.1.1. 27.1.
PAGE 86
3 Switch connectivity unit port statistics extension table TABLE 24 72 Object and OID Access Description swConnUnitC3DiscardOth er 1.3.6.1.4.1.1588.2.1.1.1. 27.1.28 Read only The number of Class 3 frames discarded due to unknown reasons. swConnUnitPCSErrorCoun ter 1.3.6.1.4.1.1588.2.1.1.1. 27.1.29 Read only The number of Physical Coding Sublayer (PCS) block errors. swConnUnitUnroutableFra meCounter 1.3.6.1.4.1.1588.2.1.1.1. 27.1.30 Read only The object represents the unroutable frame counter.
PAGE 87
Chapter 4 MAPS-MIB Objects In this chapter • MAPS-MIB overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 • MAPS Traps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 • MAPS configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 MAPS-MIB overview The descriptions of the MIB variables in this chapter come directly from the bcsiModules.
PAGE 88
4 MAPS configuration MAPS configuration The OID represents the MAPS configuration. TABLE 26 Object and OID Access mapsConfig 74 Description This object represents the MAPS configuration parameters. mapsConfigRuleName 1.3.6.1.4.1.1588.3.1.4.1.1 Read only This object indicates the rule name which associates a condition with actions that must be triggered when the specified condition is evaluated to be true. mapsConfigCondition 1.3.6.1.4.1.1588.3.1.4.1.
PAGE 89
MAPS configuration 4 TABLE 26 Fabric OS MIB Reference 53-1004120-01 Object and OID Access Description mapsConfigAction 1.3.6.1.4.1.1588.3.1.4.1.13 Read only This object indicates the actions (bitmask value) that must be triggered when the specified condition is evaluated to be true. Action bitmask value mapping are, none (0), raslog (1), snmp (2), portlog (4), port-fence (8), email (16), hareboot (32), switchpolicy (64) For example, mapsConfigAction value 3 represents both raslog and snmp actions.
PAGE 90
4 76 MAPS configuration Fabric OS MIB Reference 53-1004120-01
PAGE 91
Chapter 5 High-Availability MIB Objects In this chapter • HA-MIB overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • High-Availability group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • FRU table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • FRU history table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 92
5 High-Availability group High-Availability group This section describes the MIB objects in the High-Availability group. TABLE 28 Object and OID Access Description haStatus 1.3.6.1.4.1.1588.2.1.2.1.1 Read only Indicates whether the system is redundant. Possible values are: • redundant (0) Dual CP with standby CP ready to take over. • nonredundant (1) Single or Dual CP system where the standby CP is not available to take over operation of the switch.
PAGE 93
FRU table 5 TABLE 29 Object and OID Access Description fruSupplierId 1.3.6.1.4.1.1588.2.1.2.1.5.1.4 Read only The supplier ID. fruSupplierPartNum 1.3.6.1.4.1.1588.2.1.2.1.5.1.5 Read only The supplier part number. fruSupplierSerialNum 1.3.6.1.4.1.1588.2.1.2.1.5.1.6 Read only The supplier serial number. fruSupplierRevCode 1.3.6.1.4.1.1588.2.1.2.1.5.1.7 Read only The supplier revision code. fruPowerConsumption 1.3.6.1.4.1.1588.2.1.2.1.5.1.
PAGE 94
5 FRU history table FRU history table TABLE 31 Object and OID Access Description fruHistoryTable 1.3.6.1.4.1.1588.2.1.2.1.6 Not accessible This table gives the contents of the entire history log of the FRU events. fruHistoryEntry 1.3.6.1.4.1.1588.2.1.2.1.6.1 Not accessible An entry in this table represents a particular FRU event. fruHistoryIndex 1.3.6.1.4.1.1588.2.1.2.1.6.1.1 Read only Index of the FRU event in the history table. fruHistoryClass Read only 1.3.6.1.4.1.1588.2.1.2.1.6.1.
PAGE 95
BP table 5 TABLE 32 Object and OID Access Description cpStatus 1.3.6.1.4.1.1588.2.1.2.1.7.1.1 Read only The current status of the CP. Valid values: other (1) unknown (2) active (3) standby (4) failed (5) cpIpAddress 1.3.6.1.4.1.1588.2.1.2.1.7.1.2 Read only The IP address of the Ethernet interface of this CP. cpIpMask 1.3.6.1.4.1.1588.2.1.2.1.7.1.3 Read only The IP mask of the Ethernet interface of this CP. cpIpGateway 1.3.6.1.4.1.1588.2.1.2.1.7.1.
PAGE 96
5 HA-MIB traps TABLE 33 Object and OID Access Description bpeth1IpAddress 1.3.6.1.4.1.1588.2.1.2.1.8.1.3 Read only The IP address of the Ethernet interface Eth1 of the Scimitar blade. bpsubNetMaskIpaddress 1.3.6.1.4.1.1588.2.1.2.1.8.1.4 Read only The IP mask of the Ethernet interface of this CP. bpIpGateway 1.3.6.1.4.1.1588.2.1.2.1.8.1.5 Read only The IP address of the IP Gateway for this CP. bpSasPriVersion 1.3.6.1.4.1.1588.2.1.2.1.8.1.6 Read only The current primary version of the SAS.
PAGE 97
Chapter 6 FICON MIB Objects In this chapter • FICON MIB overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • FICON RNID group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • FICON LIRR group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • FICON RLIR group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 98
6 FICON MIB overview TABLE 35 84 FICON MIB textual conventions Name Status Description Syntax LIRRProtocol Current Represents the LIRR Protocol. INTEGER { fcp (1), sb2 (2) } FcPortID Current Represents Fibre Channel Address ID, a 24-bit value unique within the address space of a fabric. OCTET STRING (SIZE (3)) RNIDModel Current Represents the value of Model Number. OCTET STRING (SIZE (3)) RLIRLinkFailureType Current Represents the link failure type.
PAGE 99
FICON RNID group TABLE 35 6 FICON MIB textual conventions (Continued) Name Status Description Syntax LinkFormat Current Represents the frame format. INTEGER { ficon (1), common (2) } RNIDType Current Represents the value of Type Number. Displays the type number of the self-describing node. It also describes the machine type. OCTET STRING (SIZE (6)) FICON RNID group This group contains all Request Node Identification Data (RNID) group objects for FICON.
PAGE 100
6 FICON RNID group TABLE 36 86 Object and OID Access Description nodeRNIDManufacturer 1.3.6.1.4.1.1588.2.1.1.50.2. 2.1.7 Read only Identifies the manufacturer of the node. nodeRNIDManufacturerPlan t 1.3.6.1.4.1.1588.2.1.1.50.2. 2.1.8 Read only Identifies the manufacturer plant of the node. nodeRNIDSequenceNumber 1.3.6.1.4.1.1588.2.1.1.50.2. 2.1.9 Read only Identifies the sequence number of the node. nodeRNIDConnectedPortWW Read only N 1.3.6.1.4.1.1588.2.1.1.50.2. 2.1.
PAGE 101
FICON LIRR group 6 TABLE 36 Object and OID Access Description switchRNIDType 1.3.6.1.4.1.1588.2.1.1.50.2. 4.1.4 Read only Type Number associated with the switch. switchRNIDModel 1.3.6.1.4.1.1588.2.1.1.50.2. 4.1.5 Read only Model number of the RNID switch. switchRNIDManufacturer 1.3.6.1.4.1.1588.2.1.1.50.2. 4.1.6 Read only Identifies the manufacturer of the switch. switchRNIDManufacturerPla nt 1.3.6.1.4.1.1588.2.1.1.50.2. 4.1.7 Read only Identifies the manufacturer plant of the switch.
PAGE 102
6 FICON RLIR group TABLE 37 Object and OID Access Description LIRRListenerPortWWN 1.3.6.1.4.1.1588.2.1.1.5 0.3.2.1.2 Read only WWN of the Listener port. LIRRListenerPID 1.3.6.1.4.1.1588.2.1.1.5 0.3.2.1.3 Read only PID for the Listener port. LIRRRegType 1.3.6.1.4.1.1588.2.1.1.5 0.3.2.1.4 Read only Registration type: conditional or unconditional. LIRRProtocol 1.3.6.1.4.1.1588.2.1.1.5 0.3.2.1.5 Read only Protocol type supported. LIRRPortType 1.3.6.1.4.1.1588.2.1.1.5 0.3.2.1.
PAGE 103
LinkIncident MIB traps group 6 TABLE 38 Object and OID Access Description rLIRIncidentPortNumber 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.7 Read only RLIR Incident port number. This is a vendor-specific port number. rLIRConnectedPortWwn 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.8 Read only RLIR Connected port WWN. rLIRConnectedNodeWwn 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.9 Read only RLIR Connected node WWN. rLIRFabricWwn 1.3.6.1.4.1.1588.2.1.1.50.4.2.1.10 Read only RLIR Fabric WWN. rLIRLinkFailureType 1.3.6.1.4.1.
PAGE 104
6 LinkIncident MIB traps group TABLE 39 Trap name and OID 90 Variables Description linkLIRRListenerRemoved lIRRListenerPortWWN 1.3.6.1.4.1.1588.2.1.1.50.21.0.4 lIRRListenerPID lIRRIndex nodeVfId A listener for link failure incident was removed. linkRLIRFailureIncident nodeRNIDIndex 1.3.6.1.4.1.1588.2.1.1.50.21.0.5 lIRRIndex rLIRIncidentPortWwn rLIRConnectedPortWwn rLIRIndex rLIRLinkFailureType lIRRListenerPID nodeVfId A link failure incident has occurred.
PAGE 105
Chapter FibreAlliance MIB Objects 7 In this chapter • FibreAlliance MIB overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 • Connectivity unit group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 • Statistics group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 • Service group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 106
7 FibreAlliance MIB overview TABLE 40 Definitions for FCMGMT-MIB (Continued) Type definition Value Description FcEventSeverity Integer 1 (unknown) 2 (emergency) Emergency status. 3 (alert) Alert status. 4 (critical) Critical status. 5 (error) Error status. 6 (warning) Warning status. 7 (notify) Notification status. 8 (info) Informational status. 9 (debug) Debug status. 10 (mark) All messages logged. FcUnitType Integer 1 (unknown) 2 (other) None of 3–14.
PAGE 107
Connectivity unit group 7 Connectivity unit group Implementation of the connectivity group is mandatory for all systems. TABLE 41 Fabric OS MIB Reference 53-1004120-01 Object and OID Access Description uNumber 1.3.6.1.3.94.1.1 Read only The number of connectivity units present on this system (represented by this agent). Might be a count of the boards in a chassis or the number of full boxes in a rack. The connectivity unit is mapped to a switch. uNumber is always set to one. systemURL 1.3.6.1.3.
PAGE 108
7 Connectivity unit group TABLE 41 Object and OID Access Description connUnitGlobalId 1.3.6.1.3.94.1.6.1.2 Read only An optional global-scope identifier for this connectivity unit. It must be a WWN for this connectivity unit or 16 octets of value 0. The following characteristics are required. • WWN formats requiring fewer than 16 octets must be extended to 16 octets with trailing 0 octets. • If a WWN is used for connUnitId, the same WWN must be used for connUnitGlobalId.
PAGE 109
Connectivity unit group 7 TABLE 41 Object and OID Access Description connUnitNumports 1.3.6.1.3.94.1.6.1.4 Read only Number of physical ports (between 0 and the maximum number of system supported ports) in the connectivity unit (external). The Brocade switches support 0 to maximum number of system supported ports. NOTE: The ConnUnitNumports will not count the GE ports present on the FC4-16IP blade. The maximum number of supported ports are as follows.
PAGE 110
7 Connectivity unit group TABLE 41 Object and OID Access Description connUnitUrl 1.3.6.1.3.94.1.6.1.10 Read only URL to launch a management application, if applicable; otherwise an empty string. In a standalone unit, this would be the same as the top-level URL. This has the same definition as systemURL for keywords. (Same as systemURL.) The expected value for connUnitURL.0 is: “http://{a.b.c.d}” where {a.b.c.d} is the IP address of the switch if Web Tools license is available.
PAGE 111
Connectivity unit group 7 TABLE 41 Object and OID Access Description connUnitConfigurationCh angeTime 1.3.6.1.3.94.1.6.1.16 Read only The sysuptime time stamp (in centiseconds) at which the last configuration change occurred for any members of the set. In other words, this is the latest time stamp of flash memory update. This represents a union of change information for connUnitConfigurationChangeTime NOTE: This object is not supported. Fabric OS MIB Reference 53-1004120-01 connUnitNumRevs 1.3.6.1.
PAGE 112
7 Connectivity unit group TABLE 41 Object and OID Access Description connUnitControl 1.3.6.1.3.94.1.6.1.22 Read-write Controls the addressed connUnit. Each implementation might choose not to allow any or all of these values on a SET. Cold start and warm start are as defined in MIB-II and are not meant to be a factory reset.
PAGE 113
Connectivity unit group 7 TABLE 41 Fabric OS MIB Reference 53-1004120-01 Object and OID Access Description connUnitRevsTable 1.3.6.1.3.94.1.7 Not accessible Table of the revisions supported by connectivity units managed by this agent. Usage Notes This table lists the versions of hardware and software elements in the switch. One entry for the hardware platform version and another entry for the Fabric OS version. For example, for the Brocade 4100 the hardware platform number is 32.0.
PAGE 114
7 Connectivity unit group TABLE 41 Object and OID Access Description connUnitSensorInfo 1.3.6.1.3.94.1.8.1.5 Read only Miscellaneous static information about the sensor, such as its serial number. Each contains textual information about the sensor. Returns the serial ID if this is for the power supply; otherwise, returns Null. connUnitSensorMessage 1.3.6.1.3.94.1.8.1.6 Read only This describes the status of the sensor as a message.
PAGE 115
Connectivity unit group 7 TABLE 41 Fabric OS MIB Reference 53-1004120-01 Object and OID Access Description connUnitPortEntry 1.3.6.1.3.94.1.10.1 Not accessible Each entry contains the information for a specific port. connUnitPortUnitId 1.3.6.1.3.94.1.10.1.1 Read only The connUnitId value of the connectivity unit that contains this port. Same value as connUnitId. connUnitPortIndex 1.3.6.1.3.94.1.10.1.
PAGE 116
7 Connectivity unit group TABLE 41 102 Object and OID Access Description connUnitPortFCClassCap 1.3.6.1.3.94.1.10.1.4 Read only Bit mask that specifies the classes of service capability of this port. If this is not applicable, return all bits set to 0. The bits have the following definition: • unknown 0 • class-f 1 • class-one 2 • class-two 4 • class-three 8 • class-four 16 • class-five 32 • class-six 64 For an F_Port, FL_Port, or sim-port, this value is 0x000C.
PAGE 117
Connectivity unit group 7 TABLE 41 Object and OID Access Description connUnitPortStatus 1.3.6.1.3.94.1.10.1.7 Read only An overall protocol status for the port. For a U_Port, the status should be ols (9). Possible values are: • unknown (1) • unused (2) - Device cannot report this status. • ready (3) - FCAL Loop or FCPH Link reset protocol initialization has completed. • warning (4) - Do not use. • failure (5) - Port is faulty.
PAGE 118
7 Connectivity unit group TABLE 41 Object and OID Access Description connUnitPortWwn 1.3.6.1.3.94.1.10.1.10 Read only The World Wide Name of the port, if applicable; otherwise, an empty string. This is in IEEE Extended format, and the extension contains the internal port number of each port. NOTE: The internal port number is 1 less than the port index.
PAGE 119
Connectivity unit group 7 TABLE 41 Fabric OS MIB Reference 53-1004120-01 Object and OID Access Description connUnitPortControl 1.3.6.1.3.94.1.10.1.16 Read-write Controls the addressed connUnit’s port. Valid commands are: resetConnUnitPort If the addressed connUnit allows this operation to be performed to this port, the addressed port performs a vendor-specific reset operation. Examples of these operations are: • The Link Reset protocol. • The Loop Initialization protocol.
PAGE 120
7 Connectivity unit group TABLE 41 106 Object and OID Access Description connUnitPortControl 1.3.6.1.3.94.1.10.1.16 (continued) Read-write connUnitPortName 1.3.6.1.3.94.1.10.1.17 Read-write connUnitPortPhysicalNu mber 1.3.6.1.3.94.1.10.1.18 Read only This is the internal port number by which this port is known. In many implementations, this should be the same as connUnitPortIndex. Some implementations might have an internal port representation not compatible with the rules for table indices.
PAGE 121
Connectivity unit group 7 TABLE 41 Fabric OS MIB Reference 53-1004120-01 Object and OID Access Description connUnitPortProtocolCap 1.3.6.1.3.94.1.10.1.20 Read only This is the bit mask that specifies the driver-level protocol capability of this port. If this is not applicable, return all bits set to 0. Return value = 07F The bits have the following definition. • 0 = unknown • 1 = Loop • 2 = Fabric • 4 = SCSI • 8 = TCP/IP • 16 = VI • 32 = FICON connUnitPortProtocolOp 1.3.6.1.3.94.1.10.1.
PAGE 122
7 Connectivity unit group TABLE 41 Object and OID Access Description connUnitEventTable 1.3.6.1.3.94.1.11 Not accessible The table of connectivity unit events. Errors, warnings, and information should be reported in this table. This table contains the 1024 most-recent event log entries. Only external RASlog messages are supported. Fabric OS 4.4.0 and later releases do not have Panic or Debug level messages. All external messages are documented in the Fabric OS Message Reference.
PAGE 123
Connectivity unit group 7 TABLE 41 Fabric OS MIB Reference 53-1004120-01 Object and OID Access Description connUnitSEventTime 1.3.6.1.3.94.1.11.1.5 Read only This is the sysuptime time stamp when the event occurred. connUnitEventSeverity 1.3.6.1.3.94.1.11.1.6 Read only The event severity level.
PAGE 124
7 Connectivity unit group TABLE 41 110 Object and OID Access Description connUnitLinkTable 1.3.6.1.3.94.1.12 Not accessible A list of links known to this agent from this connectivity unit to other connectivity units- X is switch data and Y is other end.
PAGE 125
Connectivity unit group 7 TABLE 41 Fabric OS MIB Reference 53-1004120-01 Object and OID Access Description connUnitLinkIndex 1.3.6.1.3.94.1.12.1.2 Read only This value is used to create a unique value for each entry in the link table with the same connUnitLinkUnitId. The value can only be reused if it is not currently in use and the value is the next candidate to be used. This value is allowed to wrap at the highest value represented by the number of bits.
PAGE 126
7 Statistics group TABLE 41 Object and OID Access Description connUnitLinkUnitTypeY 1.3.6.1.3.94.1.12.1.12 Read only Type of the FC connectivity unit, as defined in connUnitType. ISL- Switch device. End devices- End device types based on an FCP Inquiry. Brocade does not support Hubs. Table 42 displays the types of the connectivity unit. connUnitLinkConnIdY 1.3.6.1.3.94.1.12.1.13 Read only This is the Fibre Channel ID of this port.
PAGE 127
Statistics group 7 TABLE 43 Object and OID Access Description connUnitPortStatIndex 1.3.6.1.3.94.4.5.1.2 Read only This object represents the port index. connUnitPortStatCountEr Read only ro 1.3.6.1.3.94.4.5.1.3 A count of the errors that have occurred on this port. connUnitPortStatCountTx Read only Objects 1.3.6.1.3.94.4.5.1.4 The number of frames that have been transmitted by this port. A Fibre Channel frame starts with SOF and ends with EOF.
PAGE 128
7 Statistics group TABLE 43 Object and OID Access Description connUnitPortStatCountP RJTFrames 1.3.6.1.3.94.4.5.1.13 Read only The number of times that FRJT was returned to this port as a result of a frame that was rejected at the destination N_Port. Return Value - 800000000 This is the total for all classes and is a Fibre Channel only statistic. NOTE: This object is not supported. connUnitPortStatCountCl ass1RxFrames 1.3.6.1.3.94.4.5.1.
PAGE 129
Statistics group 7 TABLE 43 Object and OID Access Description connUnitPortStatCountCl ass2FBSYFrames 1.3.6.1.3.94.4.5.1.22 Read only The number of times that FBSY was returned to this port because Class 2 Frame that could not be delivered to the other end of the link. This occurs if either the fabric or the destination port is temporarily busy. FBSY can only occur on SOFc1 frames (the frames that establish a connection). This is a Fibre Channel only statistic.
PAGE 130
7 Statistics group TABLE 43 Object and OID Access connUnitPortStatCountTx Read only BroadcastObjects 1.3.6.1.3.94.4.5.1.32 Description The number of broadcast frames or packets transmitted out this port. On a Fibre Channel loop, count only OPNr frames generated. Return value - 800000000 NOTE: This object is not supported. connUnitPortStatCountR xLinkResets 1.3.6.1.3.94.4.5.1.33 Read only The number of link resets received. This is a Fibre Channel only statistic.
PAGE 131
Service group 7 TABLE 43 Object and OID Access Description connUnitPortStatCountIn validOrderedSets 1.3.6.1.3.94.4.5.1.45 Read only The number of invalid ordered sets received at port. This count is part of the Link Error Status Block (LESB). (FC-PH 29.8). This is a Fibre Channel only statistic. connUnitPortStatCountFr amesTooLong 1.3.6.1.3.94.4.5.1.46 Read only The number of frames received at this port where the frame length was greater than what was agreed to in FLOGI/PLOGI.
PAGE 132
7 Service group TABLE 44 118 Object and OID Access Description connUnitSnsPortIndex 1.3.6.1.3.94.5.2.1.1.2 Read only The physical port number of this SNS table entry. Each physical port has an SNS table with 1-n entries indexed by connUnitSnsPortIdentifier (port address). connUnitSnsPortIdentifie r 1.3.6.1.3.94.5.2.1.1.3 Read only The port identifier for this entry in the SNS table. connUnitSnsPortName 1.3.6.1.3.94.5.2.1.1.4 Read only The port name for this entry in the SNS table.
PAGE 133
SNMP trap registration group 7 SNMP trap registration group TABLE 45 Object and OID Access Description trapMaxClients 1.3.6.1.3.94.2.1 Read only The maximum number of SNMP trap recipients supported by the connectivity unit. Set to 6. trapClientCount 1.3.6.1.3.94.2.2 Read only The current number of rows in the trap table. trapRegTable 1.3.6.1.3.94.2.3 Not accessible A table containing a row for each IP address or port number to which traps are sent. trapRegEntry 1.3.6.1.3.94.2.3.
PAGE 134
7 Revision number scalar TABLE 47 trapRegRowState for Read/Write State Description (Read) Description (Write) rowDestroy (1) Can never happen. Remove this row from the table. rowInactive (2) Indicates that this row does exist but that traps are not enabled to be sent to the target. If the row does not exist and the agent allows writes to the trap table, then a new row is created. The values of the optional columns are set to default values. Traps are not enabled to be sent to the target.
PAGE 135
FibreAlliance MIB traps 7 FibreAlliance MIB traps TABLE 49 Trap name and OID Variables connUnitStatusChan connUnitStatus ge connUnitState 1.3.6.1.3.94.0.1 Description The overall status of the connectivity unit has changed. Recommended severity level (for filtering) - alert. Generated when connUnitStatus changes. For a description of how the value is calculated, refer to “connUnitStatus” on page 95. Sample trap output for Fabric OS 8.0.1. connUnitStatus.16.0.0.96.105.144.109.136.0.0. 0.0.0.0.0.0.
PAGE 136
7 FibreAlliance MIB traps TABLE 49 Trap name and OID Variables Description connUnitSensorStat usChange 1.3.6.1.3.94.0.5 connUnitSensorStatus Overall status of the connectivity unit has changed. This trap is generated whenever the status of the sensors (like fan, power supply, temperature) present in the connectivity unit changes. Sample trap output for Fabric OS 8.0.1. connUnitSensorStatus.16.0.0.96.105.144.109.13 6.0.0.0.0.0.0.0.0.
PAGE 137
Chapter 8 FibreAlliance Extension MIB Objects In this chapter • FibreAlliance extension MIB overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • SFP statistics table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • Port configuration table for Fabric Assigned PWWN feature . . . . . . . . . . . • Port configuration table for encryption or compression feature . . . . . . . .
PAGE 138
8 SFP statistics table SFP statistics table TABLE 51 Object and OID Access Description swSfpStatTable 1.3.6.1.4.1.1588.2.1.1.1.28.1 Not accessible This table represents the diagnostic statistics of Small Form-factor Pluggable (SFP) optical transceivers. swSfpStatEntry 1.3.6.1.4.1.1588.2.1.1.1.28.1. 1 Not accessible An entry containing the diagnostic statistics of SFPs. swSfpTemperature 1.3.6.1.4.1.1588.2.1.1.1.28.1. 1.1 Read only This object identifies the temperature of the SFP.
PAGE 139
Port configuration table for encryption or compression feature 8 TABLE 52 Object and OID Access Description swPortFapwwnConfigEnable Read only 1.3.6.1.4.1.1588.2.1.1.1.28.2. 1.1.1 This object indicates whether or not the FAPWWN is enabled on the port: • true (1) • false (2) swPortFapwwnConfigFapwwn Read only 1.3.6.1.4.1.1588.2.1.1.1.28.2. 1.1.2 The object represents the FAPWWN assigned to the port. It returns the WWN irrespective of the state of the FAPWWN. swPortFapwwnConfigType Read only 1.3.6.1.
PAGE 140
8 Switch connectivity unit port table Switch connectivity unit port table TABLE 54 126 Object and OID Access Description swConnUnitPortTable 1.3.6.1.4.1.1588.2.1.1.1.28.4 Not accessible This table represents the port entry of the connectivity unit. swConnUnitPortEntry 1.3.6.1.4.1.1588.2.1.1.1.28.4.1 Not accessible This represents the port entry of the connectivity unit. swConnUnitPortCapableSpeeds 1.3.6.1.4.1.1588.2.1.1.1.28.4.1.
PAGE 141
Appendix A MIB Object Groupings In this appendix • Switch variables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • Sensor variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • Port variables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • Event variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 142
A Event variables • fcFxConfTable • fcFxPortStatusTable • fcFxPortPhysTable • fcFxPortCapTable Variables for statistics and measurement • Statistics group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 • fcFxPortErrorTable • fcFxPortC2AccountingTable • fcFeCapabilities group Event variables MIB variables that assist in monitoring or modifying events are in the following tables or groups. • connUnitEventTable. . . . . . . . . . . . . . . . . . . . . . .
PAGE 143
Appendix B Mapping of CLI Counters to MIB Objects In this appendix • portStatsShow command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • portErrShow command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • portStats64Show command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • portShow command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 144
B portStatsShow command TABLE 55 portStatsShow command (Continued) Counters Description MIB Location Counter Size stat_lc_rx The number of link control frames received. Object: swConnUnitLCRX Table name: swConnUnitPortStatExtentionTable OID: 1.3.6.1.4.1.1588.2.1.1.1.27.1.16 32 bits stat_mc_rx The number of multicast frames received. Object: connUnitPortStatCountRxMulticastObjects Table name: connUnitPortStatTable OID: 1.3.6.1.3.94.4.5.1.
PAGE 145
portStatsShow command TABLE 55 B portStatsShow command (Continued) Counters Description MIB Location Counter Size er64_enc_out The number of encoding error outside frames. Object: connUnitPortStatCountEncodingDisparityErrors subtracted from connUnitPortStatCountInvalidTxWords Table name: connUnitPortStatTable OID: 1.3.6.1.3.94.4.5.1.50 - 1.3.6.1.3.94.4.5.1.41 32 bits er_bad_os The number of invalid ordered sets (platformand port-specific).
PAGE 146
B portErrShow command TABLE 55 portStatsShow command (Continued) Counters Description MIB Location Counter Size er_lun_zone_miss The number of frames discarded due to LUN zoning miss. (LUN zoning is currently not supported.) Object: swConnUnitLunZoneMiss Table name: swConnUnitPortStatExtentionTable OID:1.3.6.1.4.1.1588.2.1.1.1.27.1.14 32 bits er_crc_good_eof The number of CRC errors with good end-of-frame (EOF) (platform- and port-specific).
PAGE 147
B portErrShow command TABLE 56 portErrShow command (Continued) Counters Description MIB Location Counter Size er_enc_in Number of encoding errors inside frames received (Rx). Object: connUnitPortStatCountEncodingDisparityErrors Table name: connUnitPortStatTable OID: 1.3.6.1.3.94.4.5.1.50 32 bits crc_err Number of frames with CRC errors received (Rx). Object: swConnUnitCRCWithBadEOF Table name: swConnUnitPortStatExtentionTable OID: 1.3.6.1.4.1.1588.2.1.1.1.27.1.
PAGE 148
B portStats64Show command TABLE 56 portErrShow command (Continued) Counters Description MIB Location Counter Size frjt Number of transmitted frames rejected with F_RJT (Tx). Object: connUnitPortStatCountFRJTFrames Table name: connUnitPortStatTable OID: 1.3.6.1.3.94.4.5.1.12 32 bits fbsy Number of transmitted frames busied with F_BSY (Tx). Object: connUnitPortStatCountFBSYFrames Table name: connUnitPortStatTable OID: 1.3.6.1.3.94.4.5.1.
PAGE 149
B portStats64Show command TABLE 57 portStats64Show command (Continued) Counters Description MIB Location Counter Size stat64_mc_tx Number of multicast frames transmitted. Object: connUnitPortStatCountTxMulticastObjects Table name: connUnitPortStatTable OID:1.3.6.1.3.94.4.5.1.30 64 bits tim64_rdy_pri Number of times R_RDY was high priority. Object: swConnUnitRDYPriority Table name: swConnUnitPortStatExtentionTable OID:1.3.6.1.4.1.1588.2.1.1.1.27.1.
PAGE 150
B portShow command TABLE 57 portStats64Show command (Continued) Counters Description MIB Location Counter Size stat64_fec_uncor The number of errors left uncorrected by FEC. Object: swConnUnitFECUnCorrectedCounter Table name: swConnUnitPortStatExtentionTable OID:1.3.6.1.4.1.1588.2.1.1.1.27.1.32 64 bits stat64_PRJTFram es Number of P_RJT frames transmitted. Not supported stat64_PBSYFram Number of P_BSY transmitted.
PAGE 151
portShow command TABLE 58 B portShow command (Continued) Counters Description MIB Location Counter Size stat64_fec_unc or The number of errors left uncorrected by FEC. Object: swConnUnitFECUnCorrectedCounter Table name: swConnUnitPortStatExtentionTable OID:1.3.6.1.4.1.1588.2.1.1.1.27.1.32 32 bits Link_failure Number of link failures (LF1 or LF2 states) received (Rx). Object: connUnitPortStatCountLinkFailures Table name: connUnitPortStatTable OID: 1.3.6.1.3.94.4.5.1.
PAGE 152
B portShow command TABLE 58 portShow command (Continued) Counters Description MIB Location Counter Size frjt Number of transmitted frames rejected with F_RJT (Tx). Object: connUnitPortStatCountFRJTFrames Table name: connUnitPortStatTable OID:1.3.6.1.3.94.4.5.1.12 32 bits fbsy Number of transmitted frames busied with F_BSY (Tx). Object: connUnitPortStatCountFBSYFrames Table name: connUnitPortStatTable OID:1.3.6.1.3.94.4.5.1.