Alienware 17 R4 Manual de servicio Modelo reglamentario: P31E Tipo reglamentario: P31E001
Notas, precauciones y avisos NOTA: Una NOTA indica información importante que le ayuda a hacer un mejor uso de su producto. PRECAUCIÓN: Una PRECAUCIÓN indica la posibilidad de daños en el hardware o la pérdida de datos, y le explica cómo evitar el problema. AVISO: Un mensaje de AVISO indica el riesgo de daños materiales, lesiones corporales o incluso la muerte. © 2018 - 2019 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
Tabla de contenido 1 Antes de manipular el interior del equipo............................................................................................ 9 Antes de empezar ................................................................................................................................................................9 Instrucciones de seguridad..................................................................................................................................................
12 Colocación de los módulos de memoria............................................................................................ 23 Procedure........................................................................................................................................................................... 23 Post-requisites....................................................................................................................................................................
Prerequisites....................................................................................................................................................................... 36 Procedimiento.................................................................................................................................................................... 36 24 Colocación del subwoofer.................................................................................................................
35 Extracción de la batería..................................................................................................................... 51 Prerequisites........................................................................................................................................................................51 Procedure...........................................................................................................................................................................
Procedimiento.................................................................................................................................................................... 66 Post-requisites.................................................................................................................................................................... 66 47 Extracción de la placa del logotipo...................................................................................................
Clearing BIOS (System Setup) and System passwords.....................................................................................................84 Borrado de la configuración de CMOS............................................................................................................................ 84 Flashing the BIOS...............................................................................................................................................................84 Menú de inicio...
Antes de manipular el interior del equipo NOTA: The images in this document may differ from your computer depending on the configuration you ordered. Antes de empezar 1. Guarde y cierre todos los archivos abiertos y salga de todas las aplicaciones abiertas. 2. Apague el equipo. Haga clic en Inicio > Alimentación > Apagar. NOTA: Si utiliza otro sistema operativo, consulte la documentación de su sistema operativo para conocer las instrucciones de apagado. 3.
Screw list Table 1. Screw list Component Secured to Screw type Quantity Base cover Palm-rest assembly M2.5x13 6 Battery Palm-rest assembly M2.5x5 4 Computer base Palm-rest assembly M2.5x8 14 Display assembly Palm-rest assembly M2.5x5 6 Hard-drive assembly Computer base M2.5x5 4 Hard-drive bracket Hard-drive assembly M3x3 4 Heat-sink assembly System board M2x3 7 I/O board Palm-rest assembly M2.
Después de manipular el interior del equipo PRECAUCIÓN: Leaving stray or loose screws inside your computer may severely damage your computer. 1. Coloque todos los tornillos y asegúrese de que ninguno quede suelto en el interior de equipo. 2. Conecte todos los dispositivos externos, los periféricos y los cables que haya extraído antes de manipular el equipo. 3. Coloque las tarjetas multimedia, los discos y cualquier otra pieza que haya extraído antes de manipular el equipo. 4.
Removing the base cover NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Procedure 1. Remove the six screws (M2.5x13) that secure the base cover to the computer base. 2.
6. Press and hold the power button for five seconds to ground the system board.
Colocación de la cubierta de la base NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Procedure 1. Connect the battery cable to the system board. 2.
Extracción de la unidad de disco duro NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. PRECAUCIÓN: Hard drives are fragile. Exercise care when handling the hard drive.
7. Desconecte la tarjeta mediadora de la unidad de disco duro.
Colocación de la unidad de disco duro NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. PRECAUCIÓN: Hard drives are fragile. Exercise care when handling the hard drive. Procedure 1.
Extracción de la tarjeta inalámbrica NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites Remove the base cover. Procedure 1.
Colocación de la tarjeta inalámbrica NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Procedure CAUTION: To avoid damaging the wireless card, do not place any cables under it. 1.
Extracción de la unidad de estado sólido NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. PRECAUCIÓN: Solid-state drives are fragile. Exercise care when handling the solid-state drive.
Colocación de la unidad de estado sólido NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. PRECAUCIÓN: Solid-state drives are fragile. Exercise care when handling the solid-state drive.
Extracción de los módulos de memoria NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites Remove the base cover. Procedimiento 1.
Colocación de los módulos de memoria NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Procedure 1.
Extracción de la cubierta de E/S posterior NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites Remove the base cover. Procedimiento 1. Quite los dos tornillos (M2.
Sustitución de la cubierta de E/S posterior NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Procedure 1.
Extracción de la base del equipo NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites 1. Remove the base cover. 2. Remove the wireless card. 3. Remove the solid-state drive.
6. Using a plastic scribe, gently release the tabs on the computer base from the slots on the palm-rest assembly. 7. Lift the computer base off the palm-rest assembly.
Colocación de la base del equipo NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Procedure 1. Align the screw holes on the computer base with the screw holes on the palm-rest assembly.
Extracción de la batería de tipo botón NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. PRECAUCIÓN: Removing the coin-cell battery resets the BIOS setup program’s settings to default.
Colocación de la batería de tipo botón NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Procedure 1. Adhere the coin-cell battery to the palm-rest assembly. 2.
Extracción de los altavoces NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites 1. Remove the base cover. 2. Remove the wireless card. 3. Remove the solid-state drive. 4.
Colocación de los altavoces NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Procedure 1. Using the alignment posts, place the speakers on the palm-rest assembly. 2.
Extracción de la placa de E/S NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites 1. Remove the base cover. 2. Remove the wireless card. 3. Remove the solid-state drive. 4.
Colocación de la placa de E/S NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Procedure 1. Connect the subwoofer cable to the I/O board. 2. Turn the I/O board over. 3.
Extracción del subwoofer NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites 1. Remove the base cover. 2. Remove the wireless card. 3. Remove the solid-state drive. 4.
Colocación del subwoofer NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Procedimiento 1.
Extracción del ensamblaje de la placa base NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. NOTA: Your computer’s Service Tag is stored in the system board.
8. Desconecte el cable de la batería de tipo botón de la placa base. 9. Despegue la cinta adhesiva que fija el cable de la batería de tipo botón a la placa base. 10. Desconecte el cable del puerto del adaptador de alimentación de la placa base. 11. Desconecte el cable de los altavoces de la placa base. 12. Levante el pestillo y desconecte el cable de retroiluminación de las teclas macro de la placa base. 13. Levante el pestillo y desconecte el cable de retroiluminación de las teclas macro de la placa base.
22.Extraiga el ensamblaje del disipador de calor. 23.Después de realizar todos los pasos anteriores, queda la placa base.
Colocación de la placa base NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. NOTA: Your computer’s Service Tag is stored in the system board.
Extracción del ensamblaje del disipador de calor NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. NOTA: The heat sink may become hot during normal operation.
Replacing the heat-sink assembly NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. CAUTION: Incorrect alignment of the heat sink can damage the system board and processor.
Extracción del puerto del adaptador de alimentación NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites 1. Remove the base cover. 2. Remove the wireless card. 3.
Colocación del puerto del adaptador de alimentación NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Procedure 1. Align the power-adapter port in the slot on the palm-rest assembly. 2.
Extracción de la placa del botón de encendido NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites 1. Remove the base cover. 2. Remove the wireless card. 3.
Colocación de la placa del botón de encendido NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Procedure 1.
Extracción del ensamblaje de la pantalla NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites 1. Remove the base cover. 2. Remove the wireless card. 3.
Colocación del ensamblaje de la pantalla NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Procedure 1.
Extracción de la batería NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites 1. Remove the base cover. 2. Remove the wireless card. 3. Remove the solid-state drive. 4.
Colocación de la batería NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Procedure 1. Using the alignment post, place the battery on the palm-rest assembly. 2.
Extracción de la superficie táctil NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites 1. Remove the base cover. 2. Remove the wireless card. 3. Remove the solid-state drive.
Colocación de la superficie táctil NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Procedure 1.
Post-requisites 1. Replace the battery. 2. Replace the computer base. 3. Replace the rear-I/O cover. 4. Replace the solid-state drive. 5. Replace the wireless card. 6. Replace the base cover.
Extracción del teclado NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites 1. Remove the base cover. 2. Remove the wireless card. 3. Remove the solid-state drive. 4.
Colocación del teclado NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Procedure CAUTION: Ensure that there are no cables under the keyboard. 1.
Post-requisites 1. Replace the battery. 2. Replace the power-adapter port. 3. Replace the subwoofer. 4. Replace the I/O board. 5. Replace the coin-cell battery. 6. Replace the computer base. 7. Replace the rear-I/O cover. 8. Replace the memory modules. 9. Replace the solid-state drive. 10. Replace the wireless card. 11. Replace the base cover.
Extracción del reposamanos NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites 1. Remove the base cover. 2. Remove the wireless card. 3. Remove the solid-state drive. 4.
Colocación del reposamanos NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Procedure Place the palm rest on a flat surface. Post-requisites 1. Replace the display assembly. 2.
Extracción del embellecedor de la pantalla NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites 1. Remove the base cover. 2. Remove the wireless card. 3.
5. Extraiga el módulo del rastreador ocular tobii.
Colocación del embellecedor de la pantalla NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Procedure 1. Replace the tobii eye-tracker module. 2.
Extracción del módulo del rastreador ocular Tobii NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites 1. Remove the base cover. 2. Remove the wireless card. 3.
Colocación del módulo del rastreador ocular Tobii NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance.
Extracción de la placa del logotipo NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites 1. Remove the base cover. 2. Remove the wireless card. 3.
Colocación de la placa del logotipo NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Procedimiento 1.
Extracción del panel de la pantalla NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites 1. Remove the base cover. 2. Remove the wireless card. 3.
Colocación del panel de la pantalla NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Procedure 1. Align the display panel on the display back-cover. 2.
Extracción de la cámara NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites 1. Remove the base cover. 2. Remove the wireless card. 3. Remove the solid-state drive. 4.
Colocación de la cámara NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Procedure 1. Connect the camera cable to the camera module. 2.
Extracción de las bisagras de la pantalla NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites 1. Remove the base cover. 2. Remove the wireless card. 3.
7. Despegue la cinta que fija la bisagra de la pantalla al ensamblaje de la antena y la cubierta posterior de la pantalla. 8. Extraiga los 12 tornillos (M2.5 x3) que fijan las bisagras al ensamblaje de la antena y la cubierta posterior de la pantalla. 9. Levante las bisagras de la ensamblaje de la antena y la cubierta posterior de la pantalla.
Colocación de las bisagras de la pantalla NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Procedure 1.
Extracción del ensamblaje de la antena y la cubierta posterior de la pantalla NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites 1. Remove the base cover. 2.
Colocación del ensamblaje de antena y la cubierta posterior de la pantalla NOTA: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Procedimiento 1.
Descripción general de BIOS El BIOS administra el flujo de datos entre el sistema operativo del equipo y los dispositivos conectados, como la unidad de disco duro, el adaptador de vídeo, un teclado, un mouse o una impresora. Acceso al programa de configuración del BIOS 1. Encienda (o reinicie) el equipo. 2. Pulse F2 cuando aparezca el logotipo de Dell para entrar en el programa de configuración del BIOS.
Main M.2 PCIe SSD-3 Displays the type of third SSD installed. Table 4. System setup options—Advanced menu Advanced Intel(R) SpeedStep Technology Allows you to enable or disable Intel (R) Speedstep Technology. NOTE: If enabled, the processor clock speed and core voltage are adjusted dynamically based on the processor load. Default: Enabled Virtualization Allows you to enable or disable the Intel Virtualization technology.
Advanced Touchpad Backlight Allows you to configure the touchpad backlight option. Battery Health Displays the battery health. Intel Software Guard Extensions Allows you to enable of disable the Intel Software Guard Extensions Default: Disabled BIOS Recovery Enable the user to recover from certain corrupted BIOS conditions from a recovery file on the user primary hard drive Default: Enabled Performance Options CPU Performance Mode Enables you to select the CPU performance mode.
Security UEFI Capsule Firmware Updates Enable or disable BIOS updates through UEFI capsule update packages. Table 6. System setup options—Boot menu Boot Boot List Option Displays the available boot options. File Browser Add Boot Option Allows to add the boot options. File Browser Del Boot Option Allows to delete the boot options Secure Boot Enable or disable the secure boot feature. Legacy Option ROMs Enable or disable the Legacy Option ROMs. Boot Option Priorities Displays the boot sequence.
5. Select the operating system installed on your computer. 6. Scroll down the page and expand BIOS. 7. Click Download to download the latest version of the BIOS for your computer. 8. After the download is complete, navigate to the folder where you saved the BIOS update file. 9. Double-click the BIOS update file icon and follow the instructions on the screen. Menú de inicio Este equipo incluye un menú de inicio de una vez.
Diagnostics Power and battery-status light: Indicates the power and battery-charge status. Solid amber – Computer is running on battery and the battery has less than 10 percent charge. User-defined color (AC mode) – Power adapter is connected and the battery is fully charged. User-defined color (Battery mode) – Computer is running on battery and the battery has more than 10 percent charge. User-defined color (Breathing, that is, slow decrease/increase in illumination) – Computer is in sleep state.
Getting help and contacting Alienware Self-help resources You can get information and help on Alienware products and services using these online self-help resources: Table 9. Alienware products and online self-help resources Information about Alienware products and services www.alienware.com Dell Help & Support app Tips Contact Support In Windows search, type Contact Support, and press Enter. Online help for operating system www.dell.com/support/windows www.dell.
