Dell Latitude D800 Service Manual Dell™ Latitude™ D800 Service Manual Before You Begin System Components Memory Module, Mini PCI Card, Modem, and Modules Hard Drive Bluetooth™ Card Fan Docking Doors Keyboard Display Assembly Video Card Microprocessor Thermal-Cooling Assembly Palm Rest Microprocessor Module Flashing the BIOS Reserve Battery System Board Speakers Base Latch Pin Assignments for I/O Connectors Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better
Before You Begin: Dell Latitude D800 Service Manual Back to Contents Page Before You Begin Dell™ Latitude™ D800 Service Manual Preparing to Work Inside the Computer Recommended Tools Computer Orientation Screw Identification Preparing to Work Inside the Computer CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell is not covered by your warranty.
Before You Begin: Dell Latitude D800 Service Manual NOTE: Ensure that the computer is off and not in a power management mode. If you cannot shut down the computer using the computer operating system, press and hold the power button for 4 seconds. 4. If the computer is connected to a docking station, undock it. 5. Disconnect the computer from the electrical outlet. 6. To avoid possible damage to the system board, wait 10 to 20 seconds and then disconnect any attached devices. 7.
Before You Begin: Dell Latitude D800 Service Manual 11. Remove any installed memory modules, Mini PCI cards, and modules, including a second battery if one is installed. 12. Remove the hard drive. Recommended Tools The procedures in this manual require the following tools: ● #1 Phillips screwdriver ● ¼-inch flat-blade screwdriver ● Small plastic scribe ● Flash BIOS update program floppy disk or CD Computer Orientation file:///F|/Service%20Manuals/Dell/Latitude/d800/begin.
Before You Begin: Dell Latitude D800 Service Manual 1 back 2 right 3 front 4 left Screw Identification When you are removing and replacing components, photocopy "Screw Identification" as a tool to lay out and keep track of the screws. The placemat provides the number of screws and their sizes. file:///F|/Service%20Manuals/Dell/Latitude/d800/begin.
Before You Begin: Dell Latitude D800 Service Manual Optional Module: Modem: Hard Drive: (1 each) (1 each) (1 each) Fan: Keyboard: Display Assembly: (2 each) (2 each) (2 each) file:///F|/Service%20Manuals/Dell/Latitude/d800/begin.
Before You Begin: Dell Latitude D800 Service Manual Display Bezel: Display Panel: Display Latch: (display bumpers, 8 each) (9 each) (2 each) Video Card Palm Rest: Speakers: (4 each) (2 each) (1 each) (8 each) (13 each) file:///F|/Service%20Manuals/Dell/Latitude/d800/begin.
Before You Begin: Dell Latitude D800 Service Manual System Board: (3 each) (2 each) (1 each) file:///F|/Service%20Manuals/Dell/Latitude/d800/begin.
Before You Begin: Dell Latitude D800 Service Manual Back to Contents Page file:///F|/Service%20Manuals/Dell/Latitude/d800/begin.
System Components: Dell Latitude D800 Service Manual Back to Contents Page System Components Dell™ Latitude™ D800 Service Manual NOTICE: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell is not covered by your warranty. NOTICE: Unless otherwise noted, each procedure in this document assumes that a part can be replaced by performing the removal procedure in reverse order.
System Components: Dell Latitude D800 Service Manual 1 display assembly 10 battery 2 display cable 11 release latch 3 center control cover 12 hard drive 4 keyboard 13 fan 5 palm rest 14 speakers 6 system board assembly 15 microprocessor 7 optical drive 16 thermal cooling assembly 8 reserve battery 17 system board support 9 computer base 18 video card Back to Contents Page file:///F|/Service%20Manuals/Dell/Latitude/d800/system.
Memory Module, Mini PCI Card, Modem, and Modules: Dell Latitude D800 Service Manual Back to Contents Page Memory Module, Mini PCI Card, Modem, and Modules Dell™ Latitude™ D800 Service Manual Memory Module Mini PCI Card Modem Modules Memory Module CAUTION: Before working inside your Dell™ computer, read the safety instructions in your System Information Guide.
Memory Module, Mini PCI Card, Modem, and Modules: Dell Latitude D800 Service Manual 1 captive screw 2 memory module cover NOTICE: To prevent damage to the memory module connector, do not use tools to spread the inner metal tabs that secure the memory module. 3. If you are replacing a memory module, remove the existing module. NOTICE: Handle memory modules by their edges, and do not touch the components on a module. a.
Memory Module, Mini PCI Card, Modem, and Modules: Dell Latitude D800 Service Manual 1 securing clips (2 per connector) 2 memory module NOTICE: If you need to install memory modules in two connectors, install a memory module in the connector labeled "DIMMA (Slot 1)" before you install a module in the connector labeled "DIMMB." 4. Ground yourself and install the new memory module: a. Align the notch in the module with the slot in the center of the connector. b.
Memory Module, Mini PCI Card, Modem, and Modules: Dell Latitude D800 Service Manual NOTICE: If the memory module cover is difficult to close, remove the module and reinstall it. Forcing the cover to close may damage your computer. 6. Insert the battery into the battery bay, or connect the AC adapter to your computer and an electrical outlet. 7. Turn on the computer. As the computer boots, it detects the additional memory and automatically updates the system configuration information.
Memory Module, Mini PCI Card, Modem, and Modules: Dell Latitude D800 Service Manual 1 captive screw 2 Mini PCI card/modem cover 3. If a Mini PCI card is not already installed, go to step 4. If you are replacing a Mini PCI card, remove the existing card: a. Disconnect the Mini PCI card from any attached cables. b. Release the Mini PCI card by spreading the metal securing tabs until the card pops up slightly. c. Lift the Mini PCI card out of its connector.
Memory Module, Mini PCI Card, Modem, and Modules: Dell Latitude D800 Service Manual 1 Mini PCI card connector 2 Mini PCI card 3 antenna cables (2) NOTICE: To avoid damaging the Mini PCI card, never place cables on top of or under the card. NOTICE: The connectors are keyed to ensure correct insertion. If you feel resistance, check the connectors and realign the card. 4.
Memory Module, Mini PCI Card, Modem, and Modules: Dell Latitude D800 Service Manual 1 Mini PCI card 2 antenna cables (2) 6. Replace the cover and tighten the screw. Modem CAUTION: Before working inside your computer, read the safety instructions in your System Information Guide. CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components.
Memory Module, Mini PCI Card, Modem, and Modules: Dell Latitude D800 Service Manual NOTICE: Handle components and cards by their edges, and avoid touching pins and contacts. 1. Follow the instructions in "Preparing to Work Inside the Computer." 2. Turn the computer over, and loosen the captive screw from the Mini PCI card/modem cover. 1 captive screw 2 Mini PCI card/modem cover 3. If a modem is not already installed, go to step 4. If you are replacing a modem, remove the existing modem: a.
Memory Module, Mini PCI Card, Modem, and Modules: Dell Latitude D800 Service Manual 1 modem cable 2 modem 3 pull-tab 4 screw 5 system board connector NOTICE: The cable connectors are keyed for correct insertion; do not force the connections. 4. Connect the modem cable to the modem. NOTICE: To prevent damage to the modem, press the modem into the connector directly over the connector. 5.
Memory Module, Mini PCI Card, Modem, and Modules: Dell Latitude D800 Service Manual directly over the connector on the system board. Modules Your computer ships with an optical drive installed in the module bay. However, the device screw is not installed in the optical drive but packaged separately. When you install your device in the module bay, you can install the device screw.
Memory Module, Mini PCI Card, Modem, and Modules: Dell Latitude D800 Service Manual 1 device latch release 2. Pull the device by the latch release to remove the device from the module bay. file:///F|/Service%20Manuals/Dell/Latitude/d800/upgrades.
Memory Module, Mini PCI Card, Modem, and Modules: Dell Latitude D800 Service Manual If the Device Screw Is Installed 1. If the computer is connected to a docking device (docked), undock it. See the documentation that came with your docking device for instructions. NOTICE: To prevent damage to devices, place them in a safe, dry place when they are not installed in the computer. Avoid pressing down on them or placing heavy objects on top of them. 2. Close the display and turn the computer over. 3.
Memory Module, Mini PCI Card, Modem, and Modules: Dell Latitude D800 Service Manual NOTICE: Insert devices into the module bay before you dock and turn on the computer. Back to Contents Page file:///F|/Service%20Manuals/Dell/Latitude/d800/upgrades.
Hard Drive: Dell Latitude D800 Service Manual Back to Contents Page Hard Drive Dell™ Latitude™ D800 Service Manual CAUTION: If you remove the hard drive from the computer when the drive is hot, do not touch the metal housing of the hard drive. CAUTION: Before working inside your computer, read the safety instructions in your System Information Guide. NOTICE: To prevent data loss, shut down your computer before removing the hard drive.
Hard Drive: Dell Latitude D800 Service Manual 1 M3 x 3-mm screw NOTICE: When the hard drive is not in the computer, store it in protective antistatic packaging. See "Protecting Against Electrostatic Discharge" in your System Information Guide." 3. Slide the hard drive out of the computer. Back to Contents Page file:///F|/Service%20Manuals/Dell/Latitude/d800/hdd.
Bluetooth™ Card: Dell Latitude D800 Service Manual Back to Contents Page Bluetooth™ Card Dell™ Latitude™ D800 Service Manual CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
Bluetooth™ Card: Dell Latitude D800 Service Manual 1 Bluetooth card 2 system board connector 3 Bluetooth card connector 4 cable Back to Contents Page file:///F|/Service%20Manuals/Dell/Latitude/d800/blue.
Fan: Dell Latitude D800 Service Manual Back to Contents Page Fan Dell™ Latitude™ D800 Service Manual CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. 1. Follow the instructions in "Preparing to Work Inside the Computer." 2. Remove the two M2.
Fan: Dell Latitude D800 Service Manual 1 M2.5 x 12-mm screws (2) 2 fan cover 3. Lift the fan out of the computer. Back to Contents Page file:///F|/Service%20Manuals/Dell/Latitude/d800/fan.
Docking Doors: Dell Latitude D800 Service Manual Back to Contents Page Docking Doors Dell™ Latitude™ D800 Service Manual Removing the Docking Doors CAUTION: Before working inside your computer, read the safety instructions in your System Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. 1.
Docking Doors: Dell Latitude D800 Service Manual Installing the Docking Doors Slide the side of the docking covers with the spring over the longer posts. 1 docking doors with spring 2 longer post Back to Contents Page file:///F|/Service%20Manuals/Dell/Latitude/d800/dockdoor.
Keyboard: Dell Latitude D800 Service Manual Back to Contents Page Keyboard Dell™ Latitude™ D800 Service Manual CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. 1. Follow the instructions in "Preparing to Work Inside the Computer." 2.
Keyboard: Dell Latitude D800 Service Manual 1 display 2 center control cover 3 computer base 3. Remove the center control cover: a. Open the display all the way (180 degrees) so that it lies flat against your work surface. b. Starting on the left side of the computer, use a plastic scribe or flat-blade screw driver to pry up the center control cover. c. Disconnect the center-control-cover flex cable from the system board connector using the pull-tab. d.
Keyboard: Dell Latitude D800 Service Manual 2 system board connector 4. Remove the keyboard: a. Remove the two M2.5 x 6-mm screws across the top of the keyboard. NOTICE: The keycaps on the keyboard are fragile, easily dislodged, and timeconsuming to replace. Be careful when removing and handling the keyboard. b. Rotate the keyboard up and slide it forward. c. Hold the keyboard up and slightly forward to allow access to the keyboard connector. d.
Keyboard: Dell Latitude D800 Service Manual 3 palm rest Back to Contents Page file:///F|/Service%20Manuals/Dell/Latitude/d800/keyboard.
Display Assembly: Dell Latitude D800 Service Manual Back to Contents Page Display Assembly Dell™ Latitude™ D800 Service Manual Display Assembly Display Bezel Display Panel Display Assembly CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
Display Assembly: Dell Latitude D800 Service Manual 3. Turn over the computer and open the display. 4. Remove the central control cover. 5. Disconnect the display cable using the pull-tab, and release the cable from the four cable-routing clips. 6. Lift the display out of the computer. file:///F|/Service%20Manuals/Dell/Latitude/d800/display.
Display Assembly: Dell Latitude D800 Service Manual 1 display 2 display cable connector 3 computer base 4 pull-tab 5 connector file:///F|/Service%20Manuals/Dell/Latitude/d800/display.
Display Assembly: Dell Latitude D800 Service Manual 1 display bumpers (8) 4 display panel 2 M2.5 x 6-mm screws (8) 5 top cover 3 display bezel 6 M2 x 3-mm screws (9) file:///F|/Service%20Manuals/Dell/Latitude/d800/display.
Display Assembly: Dell Latitude D800 Service Manual Display Bezel CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. 1. Follow the instructions in "Preparing to Work Inside the Computer." 2. Remove the central control cover. 3. Remove the display assembly.
Display Assembly: Dell Latitude D800 Service Manual 2. Remove the central control cover. 3. Remove the display assembly. 4. Remove the display bezel. 5. Remove the nine M2 x 3-mm screws from the display panel. 6. Lift the display panel, and rotate the display panel out of the top cover. 7. Remove the yellow tape from the top display connector. 8. Press in the tabs on both sides of the top display-cable connector, and pull the display cable connector away from the top flex-cable connector.
Display Assembly: Dell Latitude D800 Service Manual 3 tabs 9. Use the pull-tab to disconnect the bottom flex-cable connector from the inverter connector. 1 top flex-cable connector 2 top display-cable connector 3 pull-tab on bottom flexcable connector 10. Remove the yellow tape from above the bottom flex-cable connector. Back to Contents Page file:///F|/Service%20Manuals/Dell/Latitude/d800/display.
Display Assembly: Dell Latitude D800 Service Manual file:///F|/Service%20Manuals/Dell/Latitude/d800/display.
Video Card: Dell Latitude D800 Service Manual Back to Contents Page Video Card Dell™ Latitude™ D800 Service Manual CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. 1. Follow the instructions in "Preparing to Work Inside the Computer." 2.
Video Card: Dell Latitude D800 Service Manual 1 M2.5 x 6-mm screws (4) 2 video card 5. Lift the video card out of the computer. Back to Contents Page file:///F|/Service%20Manuals/Dell/Latitude/d800/video.
Microprocessor Thermal-Cooling Assembly: Dell Latitude D800 Service Manual Back to Contents Page Microprocessor Thermal-Cooling Assembly Dell™ Latitude™ D800 Service Manual Removing the Microprocessor Thermal-Cooling Assembly CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide.
Microprocessor Thermal-Cooling Assembly: Dell Latitude D800 Service Manual 1 captive screws (4) 2 microprocessor thermalcooling assembly 5. Rotate the microprocessor thermal-cooling assembly up toward the side of the computer and away from the system board. file:///F|/Service%20Manuals/Dell/Latitude/d800/thermal.
Microprocessor Thermal-Cooling Assembly: Dell Latitude D800 Service Manual Installing the Microprocessor Thermal-Cooling Assembly 1. Place the left side of the microprocessor thermal-cooling assembly under the palm rest and rotate the assembly onto the system board. 2. Tighten the four captive screws, labeled "1" through "4," in consecutive order. Back to Contents Page file:///F|/Service%20Manuals/Dell/Latitude/d800/thermal.
Palm Rest: Dell Latitude D800 Service Manual Back to Contents Page Palm Rest Dell™ Latitude™ D800 Service Manual CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. 1. Follow the instructions in "Preparing to Work Inside the Computer." 2.
Palm Rest: Dell Latitude D800 Service Manual 1 M2.5 x 12-mm screws (13) 7. Remove the two M2.5 x 4-mm screws from the top of the palm rest. file:///F|/Service%20Manuals/Dell/Latitude/d800/palmrest.
Palm Rest: Dell Latitude D800 Service Manual 1 M2.5 x 4-mm screws (2) 2 top of the palm rest 8. Disconnect the touch pad connector from the system board. file:///F|/Service%20Manuals/Dell/Latitude/d800/palmrest.
Palm Rest: Dell Latitude D800 Service Manual 1 back center of the palm rest 2 touch pad connector 3 system board connector 4 computer base NOTICE: Carefully separate the palm rest from the computer base to avoid damage to the palm rest. 9. Use your fingers to separate the palm rest from the computer base. Back to Contents Page file:///F|/Service%20Manuals/Dell/Latitude/d800/palmrest.
Microprocessor Module: Dell Latitude D800 Service Manual Back to Contents Page Microprocessor Module Dell™ Latitude™ D800 Service Manual Removing the Microprocessor Module CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
Microprocessor Module: Dell Latitude D800 Service Manual 5. To loosen the ZIF socket, use a small, flat-blade screwdriver and rotate the ZIFsocket cam screw counterclockwise until it comes to the cam stop. 1 screwdriver (perpendicular to microprocessor) 2 ZIF-socket cam screw 3 ZIF socket 4 pin-1 corner NOTE: The ZIF-socket cam screw secures the microprocessor to the system board. Take note of the arrow on the ZIF-socket cam screw, which indicates the direction to turn the cam screw. 6.
Microprocessor Module: Dell Latitude D800 Service Manual Installing the Microprocessor Module NOTICE: Ensure that the cam lock is in the fully open position before seating the microprocessor module. Seating the microprocessor module properly in the ZIF socket does not require force. NOTICE: A microprocessor module that is not properly seated can result in an intermittent connection or permanent damage to the microprocessor and ZIF socket. 1.
Flashing the BIOS: Dell Latitude D800 Service Manual Back to Contents Page Flashing the BIOS Dell™ Latitude™ D800 Service Manual 1. Ensure that the AC adapter is plugged in and that the main battery is installed properly. 2. Insert the flash BIOS update program floppy disk or CD and turn on the computer. Follow the instructions that appear on the screen. The computer continues to boot and updates the new BIOS. When the update is complete, the computer will automatically reboot. 3.
Reserve Battery: Dell Latitude D800 Service Manual Back to Contents Page Reserve Battery Dell™ Latitude™ D800 Service Manual CAUTION: Before working inside your Dell™ computer, read the safety instructions in your System Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. 1. Follow the instructions in "Preparing to Work Inside the Computer." 2.
Reserve Battery: Dell Latitude D800 Service Manual 4. Pull the reserve battery straight out of the computer base. 5. Disconnect the reserve battery cable connector from the speaker connector. 1 speaker connector 2 reserve battery Back to Contents Page file:///F|/Service%20Manuals/Dell/Latitude/d800/reserve.
System Board: Dell Latitude D800 Service Manual Back to Contents Page System Board Dell™ Latitude™ D800 Service Manual Removing the System Board CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer.
System Board: Dell Latitude D800 Service Manual 1 M2.5 x 6-mm screws (2) 2 system board support 9. Disconnect the speaker cable. 10. Remove the three M2.5 x 4-mm screws. file:///F|/Service%20Manuals/Dell/Latitude/d800/sysboard.
System Board: Dell Latitude D800 Service Manual 1 M2.5 x 4-mm screws (3) 2 system board 11. Remove the M2.5 x 12-mm screw labeled "circle B" from the computer base. file:///F|/Service%20Manuals/Dell/Latitude/d800/sysboard.
System Board: Dell Latitude D800 Service Manual 1 M2.5 x 12-mm screw (1) 12. Remove the system board from the computer base. file:///F|/Service%20Manuals/Dell/Latitude/d800/sysboard.
System Board: Dell Latitude D800 Service Manual 1 system board 2 speaker connector 3 speakers Installing the System Board 1. Perform all of the steps in "Removing the System Board" in reverse order. NOTICE: Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may result in damage to the computer. 2. Turn on the computer.
System Board: Dell Latitude D800 Service Manual 3. Insert the floppy disk or CD that accompanied the replacement system board into the appropriate drive. Follow the instructions that appear on the screen. Back to Contents Page file:///F|/Service%20Manuals/Dell/Latitude/d800/sysboard.
Speakers: Dell Latitude D800 Service Manual Back to Contents Page Speakers Dell™ Latitude™ D800 Service Manual CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. 1. Follow the instructions in "Preparing to Work Inside the Computer." 2. Remove the keyboard.
Speakers: Dell Latitude D800 Service Manual 1 speakers 2 M2.5 x 3-mm screw (1) 3 reserve battery 4 computer base Back to Contents Page file:///F|/Service%20Manuals/Dell/Latitude/d800/speakers.
Base Latch: Dell Latitude D800 Service Manual Back to Contents Page Base Latch Dell™ Latitude™ D800 Service Manual CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. 1. Follow the instructions in "Preparing to Work Inside the Computer." 2.
Base Latch: Dell Latitude D800 Service Manual 1 base latch 2 computer base Back to Contents Page file:///F|/Service%20Manuals/Dell/Latitude/d800/latch.
Pin Assignments for I/O Connectors: Dell Latitude D800 Service Manual Back to Contents Page Pin Assignments for I/O Connectors Dell™ Latitude™ D800 Service Manual USB Connector Video Connector Parallel Connector S-Video TV-Out Connector Serial Connector Dell D/Bay Connector USB Connector Pin Signal 1 USB5V+ 2 USBP– 3 USBP+ 4 GND file:///F|/Service%20Manuals/Dell/Latitude/d800/pinouts.
Pin Assignments for I/O Connectors: Dell Latitude D800 Service Manual Video Connector Pin Signal Pin Signal 1 CRT_R 9 5V+ 2 CRT_G 10 GND 3 CRT_B 11 MONITOR_DETECT– 4 NC 12 DDC_DATA 5 GND 13 CRT_HS 6 GND 14 CRT_VS 7 GND 15 DDC_CLK 8 GND Parallel Connector file:///F|/Service%20Manuals/Dell/Latitude/d800/pinouts.
Pin Assignments for I/O Connectors: Dell Latitude D800 Service Manual Pin Signal Pin Signal 1 STROBE– 10 ACK– 2 PD0 11 BUSY 3 PD1 12 PE 4 PD2 13 SLCT 5 PD3 14 AFD/3M– 6 PD4 15 ERROR– 7 PD5 16 INIT– 8 PD6 17 SLIN– 9 PD7 18-25 GND S-Video TV-Out Connector file:///F|/Service%20Manuals/Dell/Latitude/d800/pinouts.
Pin Assignments for I/O Connectors: Dell Latitude D800 Service Manual S-Video Pin Signal 1 GND 2 GND 3 DLUMA-L 4 DCRMA-L Composite Video Pin Signal 5 SP_DIF 6 DCMPS-L 7 SP_DIF Serial Connector file:///F|/Service%20Manuals/Dell/Latitude/d800/pinouts.
Pin Assignments for I/O Connectors: Dell Latitude D800 Service Manual Pin Signal Pin Signal 1 DCD 6 DSR 2 RXDA 7 RTS 3 TXDA 8 CTS 4 DTR 9 RI 5 GND Dell D/Bay Connector file:///F|/Service%20Manuals/Dell/Latitude/d800/pinouts.
Pin Assignments for I/O Connectors: Dell Latitude D800 Service Manual Pin Signal Pin Signal 1 USB_VCC 8 SMB_CLK 2 USB_D- 9 GND 3 USB_D+ 10 SHIELD GND 4 USB_GND 11 SHIELD GND 5 PWR_SRC 6 SMB_DAT 13 SHIELD GND 7 MODPRES# 14 SHIELD GND 12 SHIELD GND Back to Contents Page file:///F|/Service%20Manuals/Dell/Latitude/d800/pinouts.
