Dell EMC PowerEdge T40 Technical Specifications Guide Regulatory Model: D24M Series Regulatory Type: D24M003
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2019 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
Contents 1 Dell EMC PowerEdge T40 system overview.....................................................................................4 Front view of the system..................................................................................................................................................... 5 Rear view of the system.......................................................................................................................................................
1 Dell EMC PowerEdge T40 system overview The Dell EMC PowerEdge T40 system is a tower system that supports up to: • • • • One Intel Xeon E-series processor or Intel Core i3 processor or Intel Pentium Gold processor Up to three 3.5-Inch cabled SATA drives Four UDIMM slots One cabled AC power supply unit (PSU) For more information about supported drives, see the Drive specifications section. NOTE: All instances of SATA drives, and SSDs are referred to as drives in this document, unless specified otherwise.
Front view of the system Figure 1. Front view of the system 1. 3. 5. 7. Power button/Diagnostics indicator 3.5 mm Headphone port Optical drive USB 3.0 Type-A port 2. Drive activity LED indicator 4. USB 2.0 Type-A port (2) 6. USB 3.1 Type-C port For more information about the ports, see the Ports and connectors specifications section.
Rear view of the system Figure 2. Rear view of the system 1. 3. 5. 7. 9. 11. 13. 15. 17. Service tag PS2 port (Keyboard) Display Port (2) USB 2.0 Type-A with SmartPower (2) Audio line-out port Kensington/padlock slot Power Supply Unit (PSU) Power Supply Unit (PSU) Built-in Self Test (BIST) button PSU assembly release latch 2. 4. 6. 8. 10. 12. 14. 16. Serial port PS2 port (Mouse) NIC port USB 3.
2 Technical specifications The technical and environmental specifications of your system are outlined in this section.
Chassis dimensions Figure 3. Chassis dimensions Table 1. PowerEdge T40 chassis dimensions X Y Z 176.6 mm 335 mm 359.5 mm (6.95 inches) (13.18 inches) (14.15 inches) System weight Table 2. PowerEdge T40 system weight System configuration Maximum weight (with all drives/SSDs) 1x 3.5-inch drive 8.4 Kg (18.
Table 3. Processor Specifications Supported processor Model UMA Graphics Intel Xeon E E series Intel UHD Graphics P630 Intel Core i3 i3-9100 Intel UHD Graphics 630 Intel Pentium Gold G5400 Intel UHD Graphics 610 NOTE: Processor availability is subject to change and may vary by region/country. Supported operating systems The PowerEdge T40 supports the following operating systems: • • • Microsoft Windows Server 2016 Microsoft Windows Server 2019 Ubuntu 18.
Table 5. Expansion card slots supported on the system board PCIe slot Slot Type Slot 1 Slot 4 PCIe slot height PCIe x16 Gen3 Processor Full Height PCI Platform Controller Hub Full Height PCIe x4 Gen 3 (open ended) Platform Controller Hub Full Height PCIe x4 Gen 3 (open ended) Platform Controller Hub Full Height Slot 2 Slot 3 Processor Connection Maximum Add-in Card Length Half length Half length Half length Half length NOTE: The expansion cards are not hot swappable.
Optical drives The PowerEdge T40 system supports the following optical drives. Table 8. Supported optical drive type Supported drive type Supported number of drives Slim 9.5 mm SATA DVD+/-RW drive One NOTE: External optical drives can be connected through the USB ports. Ports and connectors specifications USB ports specifications The PowerEdge T40 system supports the USB ports mentioned below: Table 9. PowerEdge T40 system USB specifications Front Panel • • • Two USB 2.
Table 10. Temperature specifications Temperature Specifications Storage -40–65°C (-40–149°F) Continuous operation (for altitude less than 900 m or 2953 ft) 10–35°C (50–95°F) with no direct sunlight on the equipment Fresh air T40 do not support Fresh air (Expanded operating temperature) Maximum temperature gradient (operating and storage) 20°C/h (36°F/h) Table 11. Relative humidity specifications Relative humidity Specifications Storage 5% to 95% RH with 27°C (80.6°F) maximum dew point.
Ambient 25°C 30°C 35°C NOTE: The PowerEdge T40 does not support enterprise-class drives. Card Limited to Tier 2 PCIe cards Or PCIe cards do not require system level cooling assistance up to a local ambient temperature of 55°C Particulate and gaseous contamination specifications Table 17. Particulate contamination specifications Particulate contamination Specifications Air filtration Data center air filtration as defined by ISO Class 8 per ISO 14644-1 with a 95% upper confidence limit.
3 System diagnostics and indicator codes The diagnostic indicators on the system front panel display system status during system startup. Topics: • • • • • • • Front panel indicator codes NIC indicator codes Power supply unit Built-in Self Test Enhanced Pre-Boot System Assessment — ePSA diagnostics Diagnostics Diagnostic error messages System error messages Front panel indicator codes NOTE: No diagnostic indicators are lit when the system is turned off.
NIC indicator codes Each NIC on the back panel has an indicator that provides information about the network activity and link status. The activity LED indicates whether the NIC is currently connected or not. The link LED indicates the speed of the connected network. Figure 4. NIC indicators 1. link indicator 2. activity indicator Table 20. NIC indicators Convention Status Condition A Link and activity indicators are off The NIC is not connected to the network.
4. Press the PSU BIST button. • • If the LED turns on and remains on while the BIST button is pressed, it indicates that the power-supply unit is functional. Continue with troubleshooting steps for other devices. If the LED does not turn on, it indicates a power-supply unit failure. Replace the power supply unit. Enhanced Pre-Boot System Assessment — ePSA diagnostics The ePSA diagnostics (also known as system diagnostics) performs a complete check of your hardware.
Table 21.
Error messages Description THE FILE BEING COPIED IS TOO LARGE FOR THE DESTINATION DRIVE The file that you are trying to copy is too large to fit on the disk, or the disk is full. Try copying the file to a different disk or use a larger capacity disk. A FILENAME CANNOT CONTAIN ANY OF THE FOLLOWING CHARACTERS: \ / : * ? " < > | - Do not use these characters in filenames. GATE A20 FAILURE A memory module may be loose. Reinstall the memory module or, if necessary, replace it.
Error messages Description MEMORY ADDRESS LINE FAILURE AT ADDRESS, READ VALUE EXPECTING VALUE A memory module may be faulty or improperly seated. Reinstall the memory module or, if necessary, replace it. MEMORY ALLOCATION ERROR The software you are attempting to run is conflicting with the operating system, another program, or a utility. Shut down the computer, wait for 30 seconds, and then restart it. Run the program again. If the error message still appears, see the software documentation.
Error messages Description UNEXPECTED INTERRUPT IN PROTECTED MODE The keyboard controller may be malfunctioning, or a memory module may be loose. Run the System Memory tests and the Keyboard Controller test in Dell Diagnostics or Contact Dell. X:\ IS NOT ACCESSIBLE. THE DEVICE IS NOT READY Insert a disk into the drive and try again. System error messages Table 23. System error messages System message Description Alert! Previous attempts at booting this system have failed at checkpoint [nnnn].
