DellTM PowerConnectTM 5324 Systems User’s Guide Addendum 1
www.dell.com | support.dell.com Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of your computer. NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death. ____________________ Information in this document is subject to change without notice. © 2006 Dell Inc. All rights reserved.
New Features This document in an addendum to the PowerConnect 5324 user guide and includes the following topics: • Configuring LLDP • Defining SNMP Parameters • HTTP/HTTPS Upload/Download • Defining STP Root Guard • Configuring Multiple Spanning Tree • Configuring QinQ • Configuring Load Balancing 3
www.dell.com | support.dell.com Configuring LLDP The Link Layer Discovery Protocol (LLDP) allows network managers to troubleshoot and enhance network management by discovering and maintaining network topologies over multi-vendor environments. LLDP discovers network neighbors by standardizing methods for network devices to advertise themselves to other system, and to store discovered information.
Updates Interval (5-32768) — Indicates that rate at which LLDP advertisement updates are sent. The possible field range is 5 - 32768 seconds. The default value is 30 seconds. Hold Time (2-10) — Indicates the amount of time that LLDP packets are held before the packets are discarded. The possible field range is 2 - 10 seconds. The field default is 4 seconds. Reinitializing Delay (1-10) — Indicates the amount of time that passes between disabling LLDP and when reinitializing begins.
www.dell.com | support.dell.com Defining LLDP Port Settings The LLDP Port Settings page allows network administrators to define LLDP port settings, including the port number, the LLDP port number, and the type of port information advertised. The Port Settings page contains fields for configuring LLDP. To open the Port Settings page, click Security → LLDP → Port Settings in the tree view. Figure 1-2. Port Settings Port — Contains a list of ports on which LLDP is enabled.
Optional TLVs — Contains a list of optional TLVs advertised by the port. For the complete list, see the Available TLVs field. Available TLVs — Contains a list of available TLVs that can be advertised by the port. The possible field values are: Port Description— Advertises the port description. System Name — Advertises the system name. System Description — Advertises the system description. System Capabilities — Advertises the system capabilities.
www.dell.com | support.dell.
Viewing Advertised Information The LLDP Advertised Information page displays the information advertised by specific ports when advertising LLDP information. To open the Advertised Information page, click Security → LLDP → Advertised Information in the tree view. Figure 1-4. Advertised Information Port — Displays the port number from which the advertised information is sent. Device ID — Displays the advertised device ID. Capabilities — Displays the advertised device capabilities.
www.dell.com | support.dell.com Displaying the Advertised Information Table To open the Advertised Information Table, click Security → LLDP → Advertised Information → Show All in the tree view. Figure 1-5. Table 1-3. Advertised Information Table LLDP Advertised Information CLI Commands CLI Command Description show lldp local ethernet interface Displays LLDP information advertised from a specific port.
The following is an example of the CLI commands: Switch# show lldp local ethernet 1 Device ID: 0060.704C.73FF Port ID: 1 Capabilities: Bridge System Name: ts-7800-1 System description: Port description: Management address: 172.16.1.8 802.
www.dell.com | support.dell.com Viewing the LLDP Neighbor Information The Neighbors Information page contains information received from neighboring device LLDP advertisements. To open the Neighbor Information page, click Security → LLDP → Neighbors Information in the tree view. Figure 1-6. Neighbors Information Port — Displays the neighboring port number. Device ID — Displays the neighboring device ID. Port ID — Displays the neighboring port ID Capabilities — Displays the neighboring device capabilities.
Figure 1-7. Neighbors Table Table 1-4. LLDP Neighbor Information CLI Commands CLI Command Description show lldp neighbors interface Displays information about neighboring devices discovered using Link Layer Discovery Protocol (LLDP) The following is an example of the CLI commands: Switch# show lldp neighbors Port Device ID Port ID Hold Time Capabilities System Name 1 0060.704C.73FE 1 117 B ts-7800-2 1 0060.704C.73FD 1 93 B ts-7800-2 2 0060.704C.
www.dell.com | support.dell.com Defining SNMP Parameters Simple Network Management Protocol (SNMP) provides a method for managing network devices. Devices supporting SNMP run a local software (agent). The SNMP agents maintain a list of variables, which are used to manage the device. The variables are defined in the Management Information Base (MIB). The MIB contains the variables controlled by the agent.
Local Engine ID (10 - 64 Hex Characters) — Indicates the local device engine ID. The field value is a hexadecimal string. Each byte in hexadecimal character strings is two hexadecimal digits. Each byte can be separated by a period or a colon. The Engine ID must be defined before SNMPv3 is enabled. For stand-alone devices select a default Engine ID that is comprised of Enterprise number and the default MAC address. Use Default — Uses the device generated Engine ID.
www.dell.com | support.dell.com Table 1-5. SNMP Notification Commands CLI Command Description snmp-server engine ID local {engineidstring | default} Indicates the local device engine ID. The field values is a hexadecimal string. Each byte in hexadecimal character strings is two hexadecimal digits. Each byte can be separated by a period or colon. The Engine ID must be defined before SNMPv3 is enabled.
The following is an example of the CLI commands: Console (config)# snmp-server enable traps Console (config)# snmp-server trap authentication Console# show snmp Community-String Community-Access View name IP address ---------------- ----------------- --------- ---------- public view-1 All Community-String Group name IP address Type ---------------- ---------- ---------- ---- read only Traps are enabled. Authentication-failure trap is enabled.
www.dell.com | support.dell.com To open the SNMPv3 View Settings page, click System → SNMP → View Settings in the tree view. Figure 1-9. SNMPv3 View Settings View Name — Contains a list of user-defined views. The view name can contain a maximum of 30 alphanumeric characters. The possible field values are: Default — Displays the default user-defined view. DefaultSuper — Displays the default super user-defined view.
Figure 1-10. Add a View 3 Define the field. 4 Click Apply Changes. The SNMP View is added, and the device is updated. Displaying the View Table 1 Open the SNMPv3 View Settings page. 2 Click Show All. The View Table page opens. Figure 1-11. View Table Defining SNMP Views Using CLI Commands The following table summarizes the equivalent CLI commands for defining fields displayed in the SNMPv3 View Settings page. Figure 1-12.
www.dell.com | support.dell.com Figure 1-12. SNMP View CLI Commands CLI Command Description show snmp views [viewname] Displays the configuration of views.
Defining SNMP Access Control The Access Control Add Group page provides information for creating SNMP groups, and assigning SNMP access control privileges to SNMP groups. Groups allow network managers to assign access rights to specific device features, or features aspects. To open the Access Control Group page, click System→ SNMP → Access Control in the tree view. Figure 1-13. Access Control Group Group Name — The user-defined group to whom access control rules are applied.
www.dell.com | support.dell.com Read — The management access is restricted to read-only, and changes cannot be made to the assigned SNMP view. Write — The management access is read-write and changes can be made to the assigned SNMP view. Notify — Sends traps for the assigned SNMP view. Defining SNMP Groups 1 Open the Access Control Group page. 2 Click Add. The Add an Access Control Group page opens: Figure 1-14. Add an Access Control Group 3 Define the fields in the Add an Access Control Group page.
Removing SNMP Groups 1 Open the Access Control Group page. 2 Click Show All. The Access Table opens. 3 Select an SNMP group. 4 Check the Remove checkbox. 5 Click Apply Changes. The SNMP group is deleted, and the device is updated. Defining SNMP Access Control Using CLI Commands The following table summarizes the equivalent CLI commands for defining fields displayed in the Access Control Group page. Figure 1-15.
www.dell.com | support.dell.com Assigning SNMP User Security The SNMPv3 User Security Model (USM) page enables assigning system users to SNMP groups, as well as defining the user authentication method. To open the SNMPv3 User Security Model (USM) page, click System → SNMP → User Security Model in the tree view. Figure 1-16. SNMPv3 User Security Model User Name — Contains a list of user-defined user names. The field range is up to 30 alphanumeric characters.
None — No user authentication is used. Password (0-32 Characters) — Modifies the user-defined password for a group. Passwords can contain a maximum of 32 alphanumeric characters. Authentication Key (MD5-16; SHA-20 hexa chars) — Defines the HMAC-MD5-96 or HMAC-SHA-96 authentication level. The authentication and privacy keys are entered to define the authentication key. If only authentication is required, 16 bytes are defined for MD5.
www.dell.com | support.dell.com Figure 1-18. User Security Model Table Deleting an User Security Model Table Entry 1 Open the SNMPv3 User Security Model (USM) page. 2 Click Show All. The User Security Model Table opens. 3 Select a User Security Model Table entry. 4 Check the Remove checkbox. 5 Click Apply Changes. The User Security Model Table entry is deleted, and the device is updated.
The following is an example of the CLI commands: console (config)# snmp-server user John user-group auth-md5 1234 console (config)# end console (config)# show snmp users Name Group Name Auth Method Remote ------- ---------- ----------- ------ John user-group md5 Defining Communities Access rights are managed by defining communities in the Community Table. When the community names are changed, access rights are also changed.
www.dell.com | support.dell.com Read Write — The management access is read-write, for all MIBs except the community table, for which there is no access. SNMP Admin — The management access is read-write for all MIBs, including the community table. Remove — Removes a community, when selected. Defining a New Community 1 Open the SNMP Community page. 2 Click Add. The Add SNMP Community page opens: Figure 1-20.
Figure 1-21. Community Table Deleting Communities 1 Open the SNMP Community page. 2 Click Show All. The Community Table opens. 3 Select a community from the Community Table. 4 Select the Remove check box. 5 Click Apply Changes. The selected community entry is deleted, and the device is updated. Configuring Communities Using CLI Commands The following table summarizes the equivalent CLI commands for setting fields displayed in the SNMP Community page. Table 1-7.
www.dell.com | support.dell.com The following is an example of the CLI commands: console(config)# snmp-server community public_1 su 1.1.1.1 console(config)# snmp-server community public_2 rw 2.2.2.2 console(config)# snmp-server community public_3 ro 3.3.3.3 console(config)# snmp-server host 1.1.1.1 public_1 1 console(config)# snmp-server host 2.2.2.2 public_2 2 console(config)# console# show snmp Community-String Community-Access IP address public_1 super 1.1.1.1 public_2 readwrite 2.2.2.
Defining SNMPv3 Notification Filters The SNMPv3 Notification Filter page permits filtering traps based on OIDs. Each OID is linked to a device feature or a feature aspect. The SNMPV3 - Notification Filter page also allows network managers to filter notifications. To open the SNMPv3 Notification Filter page, click System → SNMP → Notification Filter in the tree view. Figure 1-22. SNMPv3 - Notification Filters Notification Filter Name — The user-defined notification filter.
www.dell.com | support.dell.com Figure 1-23. Add Filter 3 Define the relevant fields. 4 Click Apply Changes. The new filter is added, and the device is updated. Displaying the Filter Table 1 Open the SNMPv3 Notification Filter page. 2 Click Show All. The Filter Table opens. Figure 1-24. Filter Table Removing a Filter 1 Open the SNMPv3 Notification Filter page. 2 Click Show All. The Filter Table opens. 3 Select a Filter Table entry. 4 Check the Remove checkbox.
Configuring Notification Filters Using CLI Commands The following table summarizes equivalent CLI commands for defining fields displayed in the SNMPv3 Notification Filters page. Table 1-8. SNMP Notification Filter CLI Commands CLI Command Description snmp-server filter Creates or updates an SNMP notification filter. filter-name oid-tree {included | excluded} show snmp filters [filtername] Displays the configuration of SNMP notification filters.
www.dell.com | support.dell.com Figure 1-25. Notification Recipients Recipient IP — Indicates the IP address to whom the traps are sent. Notification Type — The notification sent. The possible field values are: Traps — Traps are sent. Informs — Informs are sent. SNMPv1,2 — SNMP versions 1 and 2 are enabled for the selected recipient. Define the following fields for SNMPv1 and SNMPv2: Community String (1-20 Characters) — Identifies the community string of the trap manager.
UDP Port (1-65535) — The UDP port used to send notifications. The default is 162. Filter Name — Includes or excludes SNMP filters. Timeout (1-300) — The amount of time (seconds) the device waits before resending informs. The default is 15 seconds. Retries (1-255) — The amount of times the device resends an inform request. The default is 3. Remove Notification Recipient — When checked, removes selected notification recipients. Adding a New Trap Recipients 1 Open Notification Recipients page. 2 Click Add.
www.dell.com | support.dell.com Figure 1-26. Notification Recipients Tables Deleting Notification Recipients 1 Open Notification Recipients page. 2 Click Show All. The Notification Recipients Tables page opens. 3 Select a notification recipient in either the SNMPV1,2 Notification Recipient or SNMPv3 Notification Recipient Tables. 4 Check the Remove checkbox. 5 Click Apply Changes. The recipient is deleted, and the device is updated.
Table 1-9. SNMP Notification Recipients CLI Commands CLI Command Description snmp-server v3-host {ip-address | Creates or updates a notification recipient hostname} username [traps | informs] receiving notifications in SNMP version 3. {noauth | auth | priv} [udp-port port] [filter filtername] [timeout seconds] [retries retries] Shows the current SNMP configuration. show snmp The following is an example of the CLI commands: console (config)# snmp-server host 172.16.1.
www.dell.com | support.dell.com HTTP/HTTPS Upload/Download Downloading Files The File Download From Server page contains fields for downloading system image and Configuration files from the TFTP server to the device or the HTTP/S server. To open the File Download From Server page, click System → File Management → File Download in the tree view. Figure 1-27. File Download From Server Firmware Download — The Firmware file is downloaded.
Boot Code — Downloads the Boot file. Active Image Active Image — The Image file that is currently active. Active Image After Reset — The Image file that is active after the device is reset. NOTE: The image file overwrites the non-active image. It is recommended to designate that the nonactive image will become the active image after reset, and then to reset the device following the download. During the image file download, a dialog box opens which displays the download progress.
www.dell.com | support.dell.com Downloading Files Using CLI Commands The following table summarizes the equivalent CLI commands for setting fields displayed in the File Download From Server page. Table 1-10. File Download CLI Commands CLI Command Description copy source-url destinationurl [snmp] Copies any file from a source to a destination. The following is an example of the CLI commands: console# copy running-config tftp://11.1.1.2/pp.
Uploading Files The File Upload to Server page contains fields for uploading the software from the TFTP server to the device. The image file can also be uploaded from the File Upload to Server page. To open the File Upload to Server page, click System → File Management → File Upload in the tree view. Figure 1-28. File Upload to Server Firmware Upload — Indicates that the upload is for firmware. If Firmware Upload is selected, the Configuration Upload fields are grayed out.
www.dell.com | support.dell.com Destination File Name (1-160 Characters) — Indicates the Configuration file path to which the file is uploaded. Transfer File Name — The software file to which the configuration is uploaded. The possible field values are: Running Configuration — Uploads the Running Configuration file. Startup Configuration — Uploads the Startup Configuration file. Backup Configuration — Uploads the Backup Configuration file. Uploading Files 1 Open the File Upload to Server page.
NOTE: Each "! " indicates that 10 packets were successfully transferred. Copying Files Files can be copied and deleted from the Copy Files page. To open the Copy Files page, click System→ File Management→ Copy Files in the tree view. Figure 1-29. Copy Files i Copy Configuration — When selected, copies either the Running Configuration, Startup Configuration or Backup Configuration files.
www.dell.com | support.dell.com Restoring Company Factory Default Settings 1 Open the Copy Files page. 2 Click Restore Company Factory Defaults. 3 Click Apply Changes. The company factory default settings are restored, and the device is updated. Copying and Deleting Files Using CLI Commands The following table summarizes the equivalent CLI commands for setting fields displayed in the Copy Files page. Table 1-12.
Defining STP Root Guard Defining STP Global Settings The Spanning Tree Global Settings page contains parameters for enabling STP on the device. To open the Spanning Tree Global Settings page, click Switch→ Spanning Tree→ Global Settings in the tree view. Figure 1-30. Spanning Tree Global Settings The Spanning Tree Global Settings page contains the following fields: Spanning Tree State — Enables or disables STP, Rapid STP, or MSTP on the device.
www.dell.com | support.dell.com The default path costs assigned to an interface vary according to the selected method: Interface Long Short LAG 20,000 4 1000 Mbps 20,000 4 100 Mbps 200,000 19 10 Mbps 2,000,000 100 BPDU Handling — Determines how BPDU packets are managed when STP is disabled on the port/ device. BPDUs are used to transmit spanning tree information. The possible field values are: Filtering — Filters BPDU packets when spanning tree is disabled on an interface.
Defining STP Global Parameters 1 Open the page. 2 Select Enable in the Spanning Tree State field. 3 Select the STP mode in the STP Operation Mode field, and define the bridge settings. 4 Click Apply Changes. STP is enabled on the device. Modifying STP Global Parameters 1 Open the page. 2 Define the fields in the dialog. 3 Click Apply Changes. The STP parameters are modified, and the device is updated.
www.dell.com | support.dell.com Table 1-13. STP Global Parameter CLI Commands (continued) CLI Command Description show spanning-tree [ethernet interface | port-channel portchannel-number] [instance instance-id] Displays spanning tree configuration. show spanning-tree [detail] [active | blockedports] [instance instance-id] Displays detailed spanning tree information on active or blocked ports. show spanning-tree mstconfiguration Displays spanning tree MST configuration identifier.
The following is an example of the CLI commands: console(config)# spanning-tree console(config)# spanning-tree mode rstp console(config)# spanning-tree priority 12288 console(config)# spanning-tree hello-time 5 console(config)# spanning-tree max-age 12 console(config)# spanning-tree forward-time 25 console(config)# exit console# show spanning-tree Spanning tree enabled mode MSTP Default port cost method: short Gathering information ..........
www.dell.com | support.dell.com 1/e6 enabled 128.6 100 DSBL Dsbl No P2p Intr 1/e7 enabled 128.7 100 DSBL Dsbl No P2p Intr 1/e8 enabled 128.8 100 DSBL Dsbl No P2p Intr 1/e9 enabled 128.9 100 DSBL Dsbl No P2p Intr 1/e10 enabled 128.10 100 DSBL Dsbl No P2p Intr 1/e11 enabled 128.11 19 DSBL Desg Yes P2p Intr console# show spanning-tree active Spanning tree enabled mode MSTP Default port cost method: short Gathering information ..........
Defining STP Port Settings The STP Port Settings page contains fields for assigning STP properties to individual ports. To open the STP Port Settings page, click Switch→ Spanning Tree→ Port Settings in the tree view. Figure 1-31. STP Port Settings Port — Port on which STP is enabled. STP — Enables or disables STP on the port. Fast Link — When selected, enables Fast Link mode for the port.
www.dell.com | support.dell.com Learning — The port is currently in the learning mode. The port cannot forward traffic however it can learn new MAC addresses. Forwarding — The port is currently in the forwarding mode. The port can forward traffic and learn new MAC addresses. Speed — Speed at which the port is operating. Path Cost (1-200000000) — The port contribution to the root path cost. The path cost is adjusted to a higher or lower value, and is used to forward traffic when a path being rerouted.
Modifying STP Port Properties 1 Open the STP Port Settings page. 2 Modify the Priority, Fast Link, Path Cost, and the Fast Link fields. 3 Click Apply Changes. The STP port parameters are modified, and the device is updated. Displaying the STP Port Table 1 Open the STP Port Settings page. 2 Click Show All. The STP Port Table opens.
www.dell.com | support.dell.com The following is an example of the CLI commands: console(config)# interface ethernet g5 console(config-if)# spanning-tree disable console(config-if)# spanning-tree cost 35000 console(config-if)# spanning-tree port-priority 96 console(config-if)# exit console(config)# exit console# show spanning-tree ethernet g5 Port g5 disabled State: disabled Role: disabled Port id: Port cost: 35000 Type: P2p 96.
Defining STP LAG Settings The STP LAG Settings page contains fields for assigning STP aggregating port parameters. To open the STP LAG Settings page, click Switch→ Spanning Tree→ LAG Settings in the tree view. Figure 1-32. STP LAG Settings Select a LAG — The user-defined LAG. For more information, see "Defining LAG Membership" in the Dell PowerConnect 5324 User Guide. STP — Enables or disables STP on the LAG. Fast Link — Enables Fast Link mode for the LAG.
www.dell.com | support.dell.com Learning — The LAG is in the learning mode and cannot forward traffic, but it can learn new MAC addresses. Forwarding — The LAG is currently in the forwarding mode, and it can forward traffic and learn new MAC addresses. Broken — The LAG is currently malfunctioning and cannot be used for forwarding traffic. Path Cost (1-200000000) — Amount the LAG contributes to the root path cost.
Table 1-15. STP LAG Settings CLI Commands CLI Command Description spanning-tree guard root Enables root guard on all the spanning tree instances on that interface. show spanning-tree [ethernet interface Displays spanning tree configuration.
www.dell.com | support.dell.com Figure 1-33. MSTP Settings Region Name (1-32 Characters) — Indicates user-defined MSTP region name. Revision (0-65535) — Defines unsigned 16-bit number that identifies the current MST configuration revision. The revision number is required as part of the MST configuration. The possible field range is 0-65535. Max Hops (1-40) — Defines the total number of hops that occur in a specific region before the BPDU is discarded.
Displaying the MSTP Instance Table 1 Open the MSTP Settings page. 2 Click Show All to open the MSTP Instance Table. Figure 1-34. MSTP Instance Table Defining MST Instances Using CLI Commands The following table summarizes the equivalent CLI commands for defining MST instance groups as displayed in the MSTP Settings page. Table 1-16. MSTP Instances CLI Commands CLI Command Description spanning-tree mst configuration Enters MST Configuration mode.
www.dell.com | support.dell.com Table 1-16. MSTP Instances CLI Commands CLI Command Description abort Exits the MST region configuration mode without applying configuration changes. show {current | pending} Displays the current or pending MST region configuration. Defining MSTP Interface Settings The MSTP Interface Settings page contains parameters assigning MSTP settings to specific interfaces.
Root — Provides the lowest cost path to forward packets to root device. Designated — Indicates the port or LAG via which the designated device is attached to the LAN. Alternate — Provides an alternate path to the root device from the root interface. Backup — Provides a backup path to the designated port path toward the Spanning Tree leaves. Backup ports occur only when two ports are connected in a loop by a point-to-point link.
www.dell.com | support.dell.com The MSTP Interface Table page opens: Figure 1-36.
Configuring QinQ This section contains information for configuring Customer VLANs using the Web Interface and using the CLI. QinQ tagging allows network managers to add an additional tag to previously tagged packets. Customer VLANs are configured using QinQ. Adding additional tags to the packets helps create more VLAN space. The added tag provides VLAN ID to each customer, this ensures private and segregated network traffic. The VLAN ID tag is assigned to a customer port in the service providers network.
www.dell.com | support.dell.com Figure 1-38. Create New VLAN 3 Define the VLAN ID and VLAN Name field. 4 Click 5 Click Switch > VLAN > Port Settings. The Port Settings page opens. Figure 1-39. . Port Settings 6 Select the port. 7 Set the Port VLAN Mode field to Customer. 8 Define the remaining fields. 9 Click 10 Click 64 . The VLAN Port settings are saved, and the device is updated. . The VLAN Port Table opens.
Figure 1-40. VLAN Port Table 11 Select the Port VLAN Mode. 12 Click . The customer VLAN is defined, and the device is updated. VLAN Port Settings Using CLI Commands The following table summarizes the equivalent CLI commands for viewing fields displayed in the VLAN Port Settings page. Table 1-17.
www.dell.com | support.dell.com The following is an example of the QinQ show commands.
Mac based VLANs: Group ID -------- Vlan ID ------------------ Subnet based VLANs: Group ID -------- Vlan ID ------------------ console# 67
www.dell.com | support.dell.com Configuring Load Balancing Load Balancing enables the even distribution of data and/or processing packets across available network resources. For example, load balancing may distribute the incoming packets evenly to all servers, or redirect the packets to the next available server. Load Balancing is configured on the LAG Configuration page.
Layer 2-3 — Enables load balancing based on static and dynamic MAC addresses, and source and destination IP addresses. Layer 2-3-4 — Enables load balancing based on static and dynamic MAC addresses, source and destination IP addresses, and Source and Destination UDP/TCP ports. LAG — The LAG number. Description (0-64 Characters) — Provides a user-defined description of the configured LAG. LAG Type — The port types that comprise the LAG.
www.dell.com | support.dell.com 4 Click Apply Changes. The LAG parameters are saved to the device. Displaying the LAG Configuration Table: 1 Open the LAG Configuration page. 2 Click Show All. The LAG Configuration Table opens: Figure 1-42. LAG Configuration Table Configuring LAGs with CLI Commands The following table summarizes the equivalent CLI commands for configuring LAGs as displayed in the LAG Configuration page. Table 1-18.
Table 1-18. LAG Configuration CLI Commands CLI Command Description description string Adds a description to an interface configuration. shutdown Disables interfaces that are part of the currently set context. speed bps Configures the speed of a given ethernet interface when not using auto negotiation. autobaud Sets the line for automatic baud rate detection. negotiation Enables auto negotiation operation for the speed and duplex parameters of a given interface.
www.dell.com | support.dell.
