Dell™ 3200MP Projector User's Guide The information below is provided by the supplier of the referenced device without independent verification by Dell and is subject to the restrictions and disclaimers. Safety Instructions About Your Projector Installation Using Your Projector Troubleshooting Specifications Regulatory Notices Contacting Dell Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of your projector.
Back to Contents Page Safety Instructions: Dell™ 3200MP Projector CAUTION Use the following safety guidelines to help protect your projector from potential damage and to ensure your own personal safety: The lamp becomes very hot with use. Do not attempt to replace the lamp after use until the projector has been allowed to cool down for at least 30 minutes, and follow all instructions in "Changing the Lamp." Do not touch the bulb or the lamp glass at any time.
Back to Contents Page About Your Projector: Dell™ 3200MP Projector Features Equipment Main Unit Control Panel Connection Ports Remote Control With Mouse Function and Laser Pointer Features Single chip 0.7" Texas Instruments DLP™ technology High contrast, double data rate(DDR) digital micromirror device True XGA, 1024 x 768 addressable pixels 3.5 lb (1.
S-video cable M1-A signal cable for HDTV/component RCA audio cable Mini pin to mini pin cable Composite video cable Batteries (2) Remote control with mouse function and laser pointer Dell 3200MP Projector User's Guide Dell 3200MP Projector Quick Start Card Dell 3200MP Projector Safety and Warranty Guide Owner's Manual Carrying case Main Unit
1 Control panel 2 Zoom ring 3 Focus ring 4 Zoom lens 5 Remote control receiver 6 Elevator button 1 Power button 2 Four directional keys 3 Keystone adjustment 4 Temperature warning light 5 Lamp warning light 6 Re-sync 7 Menu 8 Keystone adjustment Control Panel
9 Source 1 VGA Out (monitor loop-through) 2 Composite video connector 3 Audio input connector 4 S-video connector 5 Computer input and HDTV/ component video connector with remote mouse Connection Ports Remote Control With Mouse Function and Laser Pointer
1 Light 2 Power button 3 PU button (page up) 4 Laser pointer 5 Volume controls 6 Mute button 7 Freeze button 8 Directional pad 9 R-Sync button 10 Source button 11 PD button (page down) 12 Keystone correction 13 Zoom in/zoom out 14 Menu button CAUTION: The remote control has a Class II laser that emits radiation. To reduce the risk of injury to the eyes, do not look directly into the laser light on the remote control and do not point the laser light into anyone's eyes.
need to replace the batteries, see your Dell 3200MP Projector Quick Start Card. Do not dispose of used batteries along with household waste. Contact your local waste disposal agency for the address of the nearest battery deposit site.
Back to Contents Page Installation: Dell™ 3200MP Projector Connecting the Projector Powering On/Off the Projector Adjusting the Projected Image Changing the Lamp Connecting the Projector A. To Computer 1 Power cord 2&3 M1-A to combination VGA and USB cable B. To DVD Player: There are three possible methods of connecting to a DVD player. 1.
1 Power cord 2 M1-A signal cable for HDTV/ component 2. Connecting with S-video cable: 1 Power cord 2 S-video cable 3.
1 Power cord 2 Composite video cable Powering On/Off the Projector Powering On the Projector NOTE: Turn on the projector before you turn on the source. 1. Remove the lens cap. 2. Ensure that the power cord and appropriate signal cable(s) are securely connected. The power button light blinks green. 3. Press the power button to turn on the projector. The Dell logo will be displayed for 30 seconds. 4. Turn on your source (computer, notebook, DVD, etc...). The projector automatically detects your source.
1 Power button 2 Lens cap Powering Off the Projector DO NOT UNPLUG THE PROJECTOR BEFORE PROPERLY SHUTTING DOWN USING THE FOLLOWING STEPS. 1. Press the power button to turn off the projector. The "Power Off the Lamp?" message appears on the OSD. 2. Press the power button again. The cooling fans continue to operate for 2 minutes. 3. If the LAMP light is solid orange, replace the lamp. 4. If the TEMP light is solid orange, the projector has overheated. The display automatically shuts down.
Notice: To avoid damaging the projector, make sure that the elevator foot is fully retracted before placing the projector in its carrying case. 1 Elevator button 2 Elevator foot 3 Tilt adjustment wheel Adjusting the Projector Zoom and Focus CAUTION: To avoid damaging the projector, ensure that the zoom lens is fully retracted before moving the projector or placing the projector in its carrying case. 1. Rotate the zoom ring to zoom in and out. 2. Rotate the focus ring until the image is clear.
2 Focus ring Adjusting Projection Image Size Max Screen (Diagonal) Min. 29.7" 24.8" 82.5" 68.8" 135.2" 112.7" 187.2" 156.0" 240.0" 200.0" 292.8" 244.0" Max. 23.8"X17.8 66.0"X49.5" 108.2"X81.1" 149.8"X112.3" 192.0"X144.0" 234.2"X175.7" (WXH) Min. 19.8X14.9" 55.0"X41.3" 90.1"X67.6" 124.8"X93.6" 160.0"X120.0" 195.2"X146.4" (WXH) Distance 4.0' 11.1' 18.2' 25.2' 32.3' 39.4' Screen Size * This graph is for user reference only.
CAUTION: Do not touch the bulb or the lamp glass at any time. The bulb may explode due to improper handling, including the touching of the bulb or the lamp glass.
Back to Contents Page Using Your Projector: Dell™ 3200MP Projector Control Panel Remote Control On-Screen Display Control Panel Power See "Powering On/Off the Projector." Source Press to step through Analog RGB, DVI, Composite, Component-I, S-video, and Analog YPbPr sources when multiple sources are connected to the projector. R-Sync (Resync) Press to synchronize the projector to the input source. R-Sync will not operate if the OSD is displayed. Menu Press to activate the OSD.
1 Directional pad 2 Enter button 3 Laser radiation caution Power See "Power On/Off the Projector." Source Press the Source button to choose Analog RGB, DVI, Composite, Component-I, S-video, and Analog YPbPr sources. R-Sync If the remote control cover is open, the R-Sync button synchronizes the projector to the input source. If the remote control cover is closed, the R-Sync button functions as the right mouse button.
Freeze Press the Freeze button to temporarily stop motion video. Press the button again to resume . Mute Press the Mute button to mute or unmute the projector speaker. Volume Increases/decrease the speaker volume. Keystone Adjusts image distortion caused by tilting the projector. ( ± 30 degrees) Enter Activates the left mouse button when the remote control cover is closed. On-Screen Display The projector has a multi-language OSD that can only be displayed when an input source is present.
Brightness Adjusts the brightness of the image. Press to darken the image. Press to lighten the image. Contrast Controls the degree of difference between the lightest and darkest parts of the picture. Adjusting the contrast changes the amount of black and white in the image. Press to decrease the contrast. Press to increase the contrast. Color Temp. Adjusts the color temperature. With the higher temperature, the screen looks colder; with the lower temperature, the screen looks warmer.
This mode allows for manual adjustment of red, green, and blue color settings. Modifying these values will automatically change the color temperature to "user". Keystone Adjusts image distortion caused by tilting the projector. (± 30degrees) Zoom Press to digitally magnify an image up to 32 times on the projection screen. Press to reduce the zoomed image. Aspect Ratio Select this function to fit 1:1, 16:9 or 4:3 aspect ratio.
Audio Volume Press to decrease the volume. Press to increase the volume. Treble Control the higher frequencies of your audio source. Press to decrease the treble. Press to increase the treble. Bass Control the lower frequencies of your audio source.
Press to decrease the bass. Press to increase the bass. Mute Select the left icon to mute the volume. Select the right icon to unmute the volume. .
Select the location of the OSD on the screen. Projection Mode Front Projection-Desktop The default setting. Rear Projection-Desktop The projector reverses the image so you can project from behind a translucent screen. Front Projection-Ceiling Mount The projector turns the image upside down for ceiling-mounted projection. Rear Projection-Ceiling Mount The projector simultaneously reverses and turns the image upside down. You can project from behind a translucent screen with a ceiling-mounted projection.
Power Saving Use this function to select the power saving delay period. Press "Yes" to go into the "set time" sub menu. Set Time(Min) Set the power saving delay period as you prefer. When the projector is not receiving an input signal for the selected period of time, the projector will automatically enter power saving mode, and turn off the lamp. After a one-minute cooling period, the projector will turn back on with detection of an input signal or by pressing the "Power" button.
Factory Reset Select Yes to reset the projector to its factory default settings. Reset items include both computer image and video image settings.
Computer Image- Note: this menu is only available with computer input signal. Frequency Change the display data frequency to match the frequency of your computer graphic card. If you experience a vertical flickering bar, use the frequency function to make an adjustment. Tracking Synchronize the signal timing of the display with that of the graphic card. If you experience an unstable or flickering image, use the tracking function to correct it. Hor.
Ver. Position (Vertical Position) Press to move the image down. Press to move the image up. Video Image Menu Video Image- Note: this menu is only available with S-video, video(composite) or component 480i signal. Color Saturation Adjust a video image from black and white to fully saturated color. Press to decrease the amount of color in the image. Press to increase the amount of color in the image.
Adjust the sharpness of the image. Press to decrease the sharpness. Press to increase the sharpness. Tint Adjust the color balance of red and green. Back to Contents Page Press to increase the amount of green in the image. Press to increase the amount of red in the image.
Back to Contents Page Troubleshooting: Dell™ 3200MP Projector No image appears on the screen Partial, scrolling, or incorrectly displayed image The screen does not display your presentation Image is unstable or flickering Image has vertical flickering bar Image is out of focus The image is stretched when displaying 16:9 DVD Image is reversed Lamp is burned out or makes a popping sound Remote mouse function does not work If you experience problems with your projector, see the following troubleshooting tips.
The screen does not display your presentation If you are using a portable computer, press . Image is unstable or flickering Adjust the tracking in the OSD Computer Image tab. Image has vertical flickering bar Adjust the frequency in the OSD Computer Image tab. Image color is not correct If your graphic card output signal is "sync on Green", and you would like to display VGA at 60Hz signal, please go into "OSD--> Management --> Signal Type" and select "RGB".
Back to Contents Page Specifications: Dell™ 3200MP Projector Light Valve single-chip DLP™ technology Contrast Ratio 1800:1 Typical (Full On/Full Off) Lamp 150-watt, user-replaceable P-VIP lamp Number of Pixels 1024 x 768 Displayable Color 16.7M colors Projection Lens F/2.44–2.69, f=28.8–34.5 mm with 1.2x manual zoom lens Projection Screen Size 25-293 inches (diagonal) Projection Distance 4.0–39.4 ft (1.2m–12m) Video Compatibility NTSC, NTSC 4.
70 31.5 70 31.5 VGA 640X350 85 37.9 85 37.9 VGA 640X400 85 37.9 85 37.9 VGA 640X480 60 31.5 60 31.5 VGA 640X480 72 37.9 72 37.9 VGA 640X480 75 37.5 75 37.5 VGA 640X480 85 43.3 85 43.3 VGA 720X400 70 31.5 70 31.5 VGA 720X400 85 37.9 85 37.9 SVGA 800X600 56 35.2 56 35.2 SVGA 800X600 60 37.9 60 37.9 SVGA 800X600 72 48.1 72 48.1 SVGA 800X600 75 46.9 75 46.9 SVGA 800X600 85 53.7 85 53.7 XGA 1024X768 43.4 35.
Back to Contents Page Regulatory Notices: Dell™ 3200MP Projector Federal Communications Commission (FCC) Notice (U.S.
DLP Projector 3200MP/DELL CHC7229 * Manufactured at: Coretronic Corporation We hereby declare that this device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. * FCC Rules: Tested to comply with FCC part 15, class B * Test site at: Advance Data Technology Corporation No.
Hsinchu, Taiwan November 30, 2002 Mr. Vincent Lin Head of RD Center Canadian Regulatory Information (Canada Only) This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Note that Industry Canada regulations provided, that changes or modifications not expressly approved by Dell Computer Corporation could void your authority to operate this equipment.
MIC Notice (South Korea Only) B Class Device Please note that this device has been approved for non-business purposes and may be used in any environment, including residential areas. Polish Center for Testing and Certification Notice The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, monitor, printer, and so on) should have the same power supply source.
NOM Information (Mexico Only) The following information is provided on the device(s) described in this document in compliance with the requirements of the official Mexican standards (NOM) Exporter: Dell Computer Corporation One Dell Way Round Rock, TX 78682 Importer: Dell Computer de México, Paseo de la Reforma 2620, 11th Floor Col. Lomas Altas México DF CP 11950 Ship to: Dell Computer de Mexico, S.A. de C.V. al Cuidado de Kuehne & Nagel de México S. de R.I., Avenida Soles No. 55 Col.
Supply voltage: > 100–240 VAC Frequency: 50–60 Hz Current consumption: 1.
Back to Contents Page Contacting Dell To contact Dell electronically, you can access the following websites: www.dell.com support.dell.com (technical support) premiersupport.dell.com (technical support for educational, government, healthcare, and medium/large business customers, including Premier, Platinum, and Gold customers) For specific web address for your country, find the appropriate country section in the table below. NOTE: Toll-free numbers are for use within the country for which they are listed.
International Access Code:0011 Country Code:61 E-mail (New Zealand): nz_tech_support@dell.
Country Code:32 Corporate Sales 02 481 91 00 Fax 02 481 92 99 Switchboard 02 481 91 00 Website: support.euro.dell.com E-mail: tech_be@dell.com E-mail for French Speaking Customers: support.euro.dell.
Business Customer Service Medium, Large, Commercial, Government (100+ Employees) 1-800-326-9463 Technical Support Home & Home Office & Small Business 1-800-847-4096 Technical Support Medium, Large, Commercial, Government (100+ Employees) 1-800-387-5757 Sales (General) 1-800-387-5752 TechFax Cayman Islands General Support Chile (Santiago) Sales, Customer Support, and Technical Support toll free: 1-800-9501329 1-800-805-7541 toll free: 1230-0204823 Country Code:56 China (Xiamen) Tech Support w
2999 Large Corporate Accounts North Government and Education toll free: 800 858 2955 Large Corporate Accounts East toll free: 800 858 2020 Large Corporate Accounts East Government and Education toll free: 800 858 2669 Large Corporate Accounts Queue Team toll free: 800 858 2572 Large Corporate Accounts South toll free: 800 858 2355 Large Corporate Accounts West toll free: 800 858 2811 Large Corporate Accounts GCP toll free: 800 858 2055 Large Corporate Account Key Accounts toll-free:800-858262
Country Code:45 Fax Switchboard (Relational) 32871201 Switchboard (Home/Small Business) 32875000 Fax Switchboard (Home/Small Business) 32875001 Website: support.euro.dell.com E-mail Support (portable computers): den_nbk_support@dell.com E-mail Support (desktop computers): den_support@dell.com E-mail Support (servers): Nordic_server_support@dell.
Switchboard 0825 004700 Country Code:33 Switchboard (calls from outside of France) Sales Fax (calls from outside of France) 04 0825 04 99 75 40 00 004 700 99 75 40 001 Website: support.euro.dell.com E-mail: support.euro.dell.
Hong Kong Technical Support(Dimension™ and International Access Code:001 Inspiron™ ) Country Code:852 296-93188 Technical Support (OptiPlex™, 296-93191 Latitude ™ , and Dell Precision™ ) Customer Service (non-technical, post-sales issues) India Ireland (Cherrywood) International Access Code:16 Country Code:353 800-93-8291 Transaction Sales toll free: 800 96 4109 Large Corporate Accounts HK toll free: 800 96 4108 Large Corporate Accounts GCP HK toll free: 800 90 3708 Technical Support 1600
Code:00 Fax 02 696 821 13 Switchboard 02 696 821 12 Technical Support 02 577 826 90 Customer Care 02 577 825 55 Fax 02 577 035 30 Switchboard 02 577 821 Country Code:39 Website: support.euro.dell.com E-mail: support.euro.dell.com/it/it/emaildell/ Corporate Website: support.euro.dell.com E-mail: support.euro.dell.com/it/it/emaildell/ Jamaica General Support (dial from within Jamaica only) Japan (Kawasaki) Web site: support.jp.dell.
Customer Service (Austin, Texas, U.S.A.) 512 728-3619 Fax (Technical Support and Customer Service) (Austin, Texas, U.S.A.) 512 728-3883 Sales (Austin, Texas, U.S.A.) 512 728-4397 SalesFax (Austin, Texas, U.S.A.
Main 50-81-8800 or 01-800-888-3355 Montserrat General Support toll free:1-866-2786822 Netherlands Antilles General Support 001-800-882-1519 Netherlands (Amsterdam) Technical Support 20 674 4500 Home/Small and Medium Business 20 674 5500 International Access Code:00 Home/Small and Medium Business Fax 20 674 4775 Country Code:31 Home/Small and Medium Business Customer Care 20 674 4200 Corporate 20 674 5000 Corporate Fax 20 674 4779 Corporate Customer Care 20 674 4325 Website: s
Switchboard 671 16800 Fax Switchboard 671 16865 Country Code:47 Website: support.euro.dell.com E-mail Support (portable computers): nor_nbk_support@dell.com E-mail Support (desktop computers): nor_support@dell.com E-mail Support (servers): nordic_server_support@dell.
Puerto Rico General Support 1-800-805-7545 St. Kitts and Nevis General Support toll free:1-877-4414731 St. Lucia General Support 1-800-882-1521 St.
E-mail: support.euro.dell.com/es/es/emaildell/ Corporate Technical Support 91 902 100 130 Customer Care 91 902 118 546 Switchboard 91 722 92 00 Fax 91 722 95 83 Website: support.euro.dell.com E-mail: support.euro.dell.
E-mail for French-speaking HSB and Corporate Customers: support.euro.dell.
Health Customer Care 01344 373 194 Home/Small Business Sales 0870 907 4000 Home/Small Business Customer Care 0870 906 0010 Corporate/Public Sector Sales 01344 860 456 Website: support.euro.dell.com Customer Care website: dell.co.uk/lca/customerservices E-mail: dell_direct_support@dell.com Uruguay General Support U.S.A.
(1-877-335-5889) U.S.