Buy Online or Call 1-800-WWW-DELL Search All Dell.com USA Search Advanced Search Desktops Notebooks Servers, Storage & Networking Electronics BACK TO: USA Printers My Account Shopping Order Support My Order Status User Guide Back to Contents Page Using Your Projector: Dell™ 2300MP Projector Control Panel Remote Control On-Screen Display Control Panel Power See "Powering On/Off the Projector." Volume Increase or decrease the speaker volume.
Press to activate the OSD. Use the directional keys and Menu button to navigate through the OSD. Four Directional Keys The four directional keys can be used to toggle through the tabs in the OSD. Keystone Adjustment Press or button to adjust image distortion caused by tilting the projector. (±16 degrees) Remote Control Power See "Power On/Off the Projector." Source Press the Source button to switch between Analog RGB, Digital RGB, Composite, Component-i, S-video, and Analog YPbPr sources.
OSD. 4:3/16:9 Press 4:3/16:9 button to switch aspect ratio 1:1, 16:9, 4:3 as described below. Volume +/Press the Vol+ button to increase the volume, press the Vol- button to reduce the volume. Keystone Adjusts image distortion caused by tilting the projector. (±16 degrees) On-Screen Display The projector has a multi-language On-Screen Display (OSD) that can be displayed with or without an input source present. The OSD allows you to make image adjustments and change a variety of settings.
Brightness Adjust the brightness of the image. Press to darken the image. Press to lighten the image. Contrast Control the degree of difference between the brightest and darkest parts of the picture. Adjusting the contrast changes the amount of black and white in the image.
Press to increase the contrast. Color Temp. Adjust the color temperature. With the higher temperature, the screen looks more blue; with the lower temperature, the screen looks more red. User mode activates the values in the "color setting" menu. Color Setting This mode allows for manual adjustment of red, green, and blue color settings. Modifying these values will automatically change the color temperature to "user". Keystone Adjusts image distortion caused by tilting the projector.
be scaled to fit the width of the screen. 4:3: The input source will be scaled to fit the screen. Video Mode Select this function to optimize the display image for home use (Movie Mode or Game Mode), conference use (PC Mode) or as user preferable settings (User Mode), or use sRGB mode for more accurate color representation. When an icon is selected, the color of the icon will change to dark blue. Adjusting the settings of White Intensity or Degamma tab, will select User Mode automatically.
Audio Volume Press to decrease the volume. Press to increase the volume. Mute Select the left icon to mute the volume. Select the right icon to un-mute the volume.
Management Menu Location Select the location of the OSD on the screen. Projection Mode Front Projection-Desktop The default setting.
screen. Front Projection-Ceiling Mount The projector turns the image upside down for ceiling-mounted projection. Rear Projection-Ceiling Mount The projector simultaneously reverses and turns the image upside down. You can project from behind a translucent screen with a ceiling-mounted projection. Signal Type Manually select signal type RGB, YCbCr, YPbPr. Lamp Hour Display operating hours since lamp timer reset. Lamp Reset Use this function only after a new lamp is installed in the projector.
Power Saving Use this function to select the power saving delay period. Press "Yes" to go into the "set time" sub menu. Set Time (Min) Set the power saving delay period as you prefer. When the projector is not receiving an input signal for the selected period of time, the projector will automatically enter power saving mode, and turn off the lamp. After a one-minute cooling period, the projector will turn back on with detection of an input signal or by pressing the "Power" button.
Language Language Press or to select the preferred language.
Factory Reset Select Yes to reset the projector to its factory default settings. Reset items include both computer image and video image settings.
Computer ImageNOTE: This menu is only available with a computer input signal connected. Frequency Change the display data clock frequency to match the frequency of your computer graphics card. If you see a vertical flickering bar, use the frequency control to minimize the bars. This is a coarse adjustment. Tracking Synchronize the phase of the signal of the display with that of the graphic card. If you experience an unstable or flickering image, use the Tracking function to correct it.
Press to move the image to the right. Ver. Position (Vertical Position) Press to move the image down. Press to move the image up. Video Image Menu Video ImageNOTE: This menu is only available with S-video, Video (composite) signal connected. Saturation Adjust a video image from black and white to fully saturated color.
Press to decrease the amount of color in the image. Press to increase the amount of color in the image. Sharpness Adjust the sharpness of the image. Press to decrease the sharpness. Press to increase the sharpness. Tint Adjust the color balance of red and green. Press to increase the amount of green in the image. Press to increase the amount of red in the image. Back to Contents Page BACK TO: USA Copyright 1999-2006 Dell Inc.