Dell™ 2007FP Flat Panel Monitor About Your Monitor Front View Back View Side View Bottom View Monitor Specifications Universal Serial Bus (USB) Interface Plug and play capability Caring for Your Monitor Using Your Adjustable Monitor Stand Attaching the Stand Organizing Your Cables Using the Tilt, Swivel and Vertical Extension Removing the Stand Setting Up Your Monitor Rotating Your Monitor Changing the Rotation of Your Monitor Rotating Your Operating System Solving Problems Monitor Specific Troubleshoot
Back to Contents Page About Your Monitor Dell™ 2007FP Flat Panel Monitor Front View Monitor Specifications Back View Universal Serial Bus (USB) Interface Side View Plug and play capability Bottom View Caring for Your Monitor Front View 1 Input indicators 2 Input Source Select 3 OSD Menu / Select 4 Down (-) 5 Up (+) 6 Power button (with power light indicator) Back View
1 VESA mounting holes (100mm) (Behind attached base plate) Use to mount the monitor. 2 Connectors label Indicate the positions and types of connectors. 3 Barcode serial number label Refer to this label if you need to contact Dell for technical support. 4 Security lock slot Use a security lock with the slot to help secure your monitor. 5 Monitor Lock/Release Button Press to release the stand from the monitor. 6 Regulatory rating label List the regulatory approvals.
Left side 1 USB downstream ports Bottom View 1 AC power cord connector 2 DVI connector 3 VGA connector 4 Composite video connector 5 S-Video connector 6 USB upstream port 7 USB downstream ports 8 DC power connector for Dell™ Soundbar Monitor Specifications General Model number 2007FP Flat Panel Screen type Active matrix - TFT LCD
Screen dimensions 20.1 inches (20.1-inch viewable image size) Preset display area: Horizontal 408 mm (16.1 inches) Vertical 306 mm (12.1 inches) Pixel pitch 0.
Signal cable type D-sub: Detachable, Analog, 15pin, shipped attached to the monitor DVI-D: Detachable, Digital, 24pin, shipped detached from the monitor S-video: Not included with display Composite: Not included with display Dimensions (with stand): Height (fully extended in portrait mode) 547.6 mm (21.6 inches) Height (compressed/locked in landscape mode) 367 mm (14.5 inches) Width 445.3 mm (17.5 inches) Depth 193.50 mm ( 7.6 inches) Weight Monitor (Stand and Head) 6.9 Kg (15.
VGA Connector Pin Number 15-pin Side of the Connected Signal Cable 1 Video-Red 2 Video-Green 3 Video-Blue 4 GND 5 Self-test 6 GND-R 7 GND-G 8 GND-B 9 Computer 5V/3.
14 +5V / +3.
Pin Number 4-pin Side of the connector 1 DMU 2 VCC 3 DPU 4 GND USB Downstream Connector Pin Number 4-Pin Side of the Signal Cable 1 VCC 2 DMD 3 DPD 4 GND USB Ports l l 1 upstream - rear 4 downstream - 2 on rear; 2 on left side NOTE: USB 2.0 capability requires 2.
Back to Contents Page Appendix Dell™ 2007FP Flat Panel Monitor FCC Identification Information Safety Instructions Contacting Dell FCC Identification Information FCC Class B This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer's instruction manual, may cause interference with radio and television reception.
l Never insert anything metallic into the monitor openings. Doing so may create the danger of electric shock. l To avoid electric shock, never touch the inside of the monitor. Only a qualified technician should open the monitor case. l Never use your monitor if the power cable has been damaged. Ensure that nothing rests on your computer's cables and that the cables are not located where they can be stepped on or tripped over.
Country Code: 54 la_enterprise@dell.com Customer Care toll-free: 0-800- City Code: 11 Tech Support Tech Support Services Sales toll-free: 800toll-free: 0-8000-810- Website: www.dell.com.aw Aruba E-mail: la-techsupport@dell.com Technical Support Australia ( Sydney ) toll-free: 800 Website: support.ap.dell.com International Access Code: 0011 E-mail:support.ap.dell.com/contactus Country Code: 61 City Code: 2 General Support 13DELL Website: support.euro.dell.
Customer Service (printer, projectors, televisions, handhelds, digital jukebox, and wireless) Canada ( North York , Ontario ) International Access Code: 011 Hardware Warranty Support (Home Sales/Small Business) Hardware Warranty Support (med./large bus., government) Hardware Warrantu Support (printers,projectors, televisions, handhelds,digital jukebox, and wireless) Country Code: 56 1-877- Sales (med./large bus., government) toll-free: 1-8001 866 440 3355 E-mail: la-techsupport@dell.
Technical Fax 22537 2728 Switchboard 22537 2711 Website: support.euro.dell.
Technical Support Customer Care 0825 004 719 0825 338 339 Switchboard 01 55 94 71 00 Sales 01 55 94 71 00 Fax 01 55 94 71 01 Website: support.euro.dell.com E-mail: tech_support_central_europe@dell.
Sales (Home and Small Business) 1600 33 8046 Website: support.euro.dell.com E-mail: dell_direct_support@dell.
Japan ( Kawasaki ) Technical Support (PDAs, projectors, printers, routers) International Access Code: 001 Technical Support outside of Japan (PDAs, projectors, printers, routers) toll-free: 0120 Country Code: 81 Faxbox Service 044- City Code: 44 24-Hour Automated Order Status Service 044- Customer Care 044- Business Sales Division (up to 400 employees) 044- Preferred Accounts Division Sales (over 400 employees) 044- Public Sales (government agencies, educational institutions, and medical in
Country Code: 52 001-877Customer Service or 001-87750 Main or 01-800E-mail: la-techsupport@dell.com Montserrat General Support toll-free: 1-866- E-mail: la-techsupport@dell.com Netherlands Antilles General Support 001-800- Website: support.euro.dell.
Portugal Technical Support International Access Code: 00 Country Code: 351 Customer Care Sales Fax 707200149 800 300 413 800 300 410 or 800 300 411 or 800 300 412 or 21 422 07 10 21 424 01 12 E-mail: la-techsupport@dell.com Puerto Rico Technical Support toll-free: 1-866- Website: www.dell.com/kn St. Kitts and Nevis E-mail: la-techsupport@dell.com Technical Support toll-free: 1-866- Website: www.dell.com/lc St. Lucia E-mail: la-techsupport@dell.com Technical Support toll-free: 1-866- Website: www.
Fax 91 722 95 83 Website: support.euro.dell.com Technical Support for XPS Sweden (Upplands Vasby) 0771 340 340 Technical Support for all other Dell products 08 590 05 199 International Access Code: 00 Relational Customer Care 08 590 05 642 Country Code: 46 Home/Small Business Customer Care 08 587 70 527 Employee Purchase Program (EPP) Support 020 140 14 44 Technical Support Fax 08 590 05 594 Sales 08 590 05 185 City Code: 8 Website: support.euro.dell.
Local Government & Education Customer Care 01344 373 199 Health Customer Care 01344 373 194 Technical Support Technical Support for XPS (Sasi: do we need to change to XPSTM) 0870 366 4180 Technical Support (Corporate/Preferred Accounts/PAD [1000+ employees]) 0870 908 0500 General Technical Support for all other products 0870 908 0800 Home and Small Business Fax 0870 907 4006 Website: www.dell.com/tt Uruguay E-mail: la-techsupport@dell.
Back to Contents Page Rotating Your Monitor Dell™ 2007FP Flat Panel Monitor Changing the Rotation of Your Monitor Rotating Your Operating System Changing the Rotation of Your Monitor Before you rotate the monitor, your monitor should be fully vertically extended (Vertical Extension) and fully tilted (Tilt) up to avoid hitting the bottom edge of the monitor.
Back to Contents Page Setting Up Your Monitor Dell™ 2007FP Flat Panel Monitor Connecting Your Monitor Using the Front Panel Buttons Using the OSD Setting the Optimal Resolution Using the Dell™ Soundbar (Optional) Connecting Your Monitor CAUTION: Before you begin any of the procedures in this section, follow the Safety Instructions.
1 AC power cord connector 2 DVI connector 3 VGA connector 4 Composite video connector 5 S-Video connector
6 USB upstream port 7 USB downstream ports 8 DC power connector for Dell™ Soundbar To connect your monitor to the computer perform the following steps/instructions. l l l l l l l Turn off your computer and disconnect the power cable. Connect either the white (digital DVI-D) or the blue (analog VGA) display connector cable to the corresponding video port on the back of your computer. Do not use both cables on the same computer.
B The MENU button is used to launch the on-screen display(OSD) and select the OSD Menu. See Accessing the Menu System OSD Menu / Select C ,D Use these buttons for navigating and adjusting the slider-bar(decrease/increase ranges) controls in the OSD. Down (-) and Up (+) E The green LED indicates the monitor is on and fully functional. An amber LED indicates DPMS power save mode. The Power button turns the monitor on and off.
Icon Menu and Submenus Description EXIT Select to exit the main menu. BRIGHTNESS & CONTRAST This menu is to activate Brightness/Contrast adjustment. Back Brightness Push to select Back to go back to the main menu. Brightness adjusts the luminance of the backlight. Push the Contrast button to increase brightness and push the button to decrease brightness (min 0 ~ max 100). Adjust Brightness first, and then adjust Contrast only if further adjustment is necessary.
VGA Select VGA input when you are using the analog (VGA) connector. Push to select the VGA input source. DVI-D Select DVI-D input when you are using the Digital (DVI) connector. Push to select the DVI input source. S-Video Composite Select S-Video input when you are using S-Video connector. Push Select Composite input when you are using composite video connector. Push Scan for Sources Push button to scan for available input signals. Exit Menu Push to exit the OSD main menu.
Color Reset Exit Menu IMAGE MODES Return your monitor color settings to those that were set at the time of manufacture. Push to exit the OSD main menu. There are 3 image modes for different usage. Image mode submenu for VGA/DVI-D input Image mode submenu for Video input or NOTE: Image modes are different between the VGA/DVI-D and Video inputs Back Push to select Back to go back to the main menu. VGA/DVI-D input Desktop Mode Multimedia Mode Gaming Mode Mode suitable for desktop applications.
Back Wide Mode Push to select Back to go back to the main menu. Adjust the image ratio as 1:1, aspect or full screen. NOTE: Wide Mode adjustment is not required at optimal preset resolution 1600 x 1200. H Position V Position When making changes to either the 'Horizontal' or 'Vertical' settings, no changes will occur to the size of the viewing area: the image will simply be shifted in response to your selection/change. Use the Sharpness Zoom and This feature can make the image look sharper or softer.
Back Language Push to select Back to go back to the main menu. Language option to set the OSD display to one of five languages (English, Espanol, Francais, Deutsch, Japanese). Menu Horizontal Position Menu Vertical Position Menu Timer and buttons move OSD to the left and right. and buttons move OSD up and down. OSD Hold Time: Sets the length of time the OSD will remain active after the last time you pressed a button.
input) Back Mode When selected PIP PIP Source PIP Position or PIP Size NOTE: When using DVI source, the contrast adjustment is not available. PIP Contrast Push to select Back to go back to the main menu. There is one mode: PIP (Picture in Picture) Use and to browse and to select "Off" or "PIP". When PIP on, choose "SWAP" to switch the main-screen and sub-screen in PIP mode. PIP Hue/Tint Select an input signal for PIP. (VGA/DVI/S-Video/Composite) Use PIP Saturation and to browse and to select.
message: This means that the monitor cannot synchronize with the signal that it is receiving from the computer. Either the signal is too high or too low for the monitor to use. See Monitor Specifications for the Horizontal and Vertical frequency ranges addressable by this monitor. Recommended mode is 1600 X 1200 @ 60Hz. You will see the following message before the DDC/CI function is disabled.
Setting the Optimal Resolution 1. 2. 3. 4. Right-click on the desktop and select Properties. Select the Settings tab. Set the screen resolution to 1600 x 1200. Click OK. If you do not see 1600 x 1200 as an option, you may need to update your graphics driver. Depending on your computer, complete one of the following procedures. If you have a Dell™ desktop or portable computer: ¡ Go to support.dell.com, enter your service tag, and download the latest driver for your graphics card.
NOTE: Soundbar Power Connector - 12V DC output is for optional Dell™ Soundbar only. NOTICE: DO NOT USE WITH ANY DEVICE OTHER THAN DELL Soundbar. 1. Working from the rear of the monitor, attach Soundbar by aligning the two slots with the two tabs along the bottom rear of the monitor. 2. Slide the Soundbar to the left until it snaps into place. 3. Connect the Soundbar with the DC power connector. 4. Insert the mini stereo plug from the rear of the Soundbar into the computer's audio output jack.
Back to Contents Page Solving Problems Dell™ 2007FP Flat Panel Monitor Monitor Specific Troubleshooting Common Problems Video Problems Product Specific Problems Universal Serial Bus (USB) Specific Problems Dell™ Soundbar (Optional) Troubleshooting CAUTION: Before you begin any of the procedures in this section, follow the Safety Instructions.
Missing Pixels Stuck-on Pixels Brightness Problems LCD screen has spots l LCD screen has bright spots l Picture too dim or too bright l l l l l Cycle power on-off These are pixels that are permanently off and is a natural defect that occurs in LCD technology Cycle power on-off These are pixels that are permanently on and is a natural defect that occurs in LCD technology Perform monitor reset on "Factory Reset" Auto Adjust via OSD Adjust brightness & contrast controls via OSD NOTE: When using
Product Specific Problems SPECIFIC SYMPTOMS WHAT YOU EXPERIENCE Screen image is too small Image is centered on screen, but does not fill entire viewing area POSSIBLE SOLUTIONS l Perform monitor reset on "Factory Reset" Cannot adjust the monitor with the buttons on the front panel OSD does not appear on the screen l Turn the monitor off and unplug the power cord and then plug back and power on The monitor will not go into power saving mode. No picture, the LED light is green.
l l l l Distorted Sound Other audio source is used. l l l l l Unbalanced Sound Output Sound from only one side of Soundbar l l l l l l Low Volume Volume is too low. l l l l l Back to Contents Page Turn the Power/Volume knob on the Soundbar counter-clockwise to a lower volume setting. Clean and reseat the audio line-in plug. Troubleshoot the computer's sound card. Test the Soundbar using another audio source (i.e. portable CD player). Clear any obstructions between the Soundbar and the user.
Back to Contents Page Using Your Adjustable Monitor Stand Dell™ 2007FP Flat Panel Monitor Attaching the Stand Organizing Your Cables Using the Tilt, Swivel and Vertical Extension Removing the Stand Attaching the Stand 1. 2. 3. Place the stand on a flat surface. Fit the groove on the back of the monitor onto the 2 tabs of upper stand. Lower the monitor so that the monitor mounting area snaps on or locks to stand.
NOTE: Stand is detached and extended when the monitor is shipped from the factory. Vertical Extension Stand extends vertically up to 130mm via the Lock down / release button. NOTE: If locked in the down position, press the Lock down / release button on the bottom rear of stand. Lift the front panel up and extend the stand to the desired height. NOTICE: Before relocating or moving the monitor to a different location, make sure that the stand is LOCKED DOWN.
NOTE: To prevent scratches on the LCD screen while removing the stand, ensure that the monitor is placed on a clean surface.