Dell™ XPS™ 200 Owner’s Manual front-panel door (open) optional floppy drive or Media Card Reader* diagnostic lights hard-drive activity light front-panel door (push to open) headphone connector CD or DVD drive light microphone connector USB 2.
Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of your computer. NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death. If you purchased a Dell™ n Series computer, any references in this document to Microsoft® Windows® operating systems are not applicable.
Contents Finding Information 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Setting Up and Using Your Computer Setting Up a Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printer Cable . . . . . . . Connecting a USB Printer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Changing the Display Settings . . . . . . . . . . . . . . . . . . . . .
Using Intel® Viiv™ Quick Resume Technology (Optional) . . . . . . . . . . . 26 . . . . . . . . . . . . . . . . . . . . . . . . 27 27 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Enabling the QRT Feature in System Setup . . . . . Enabling the QRT feature in the Operating system . Hyper-Threading . 2 Solving Problems Troubleshooting Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 . . .
Sound and Speaker Problems . . . . . . . . . . . . . . . . . . . . . . . . . . Video and Monitor Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 43 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 If the screen is blank . . . . . .
Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Drives . Hard Drive 73 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 77 . . . . . . . . . . . . . . . . . . . . . . . . . .
5 Appendix Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 System Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 Overview . . . . . . . Entering System Setup System Setup Options . Boot Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 100 102 105 . .
Contents
Finding Information NOTE: Some features may not be available for your computer or in certain countries. NOTE: Additional information may ship with your computer. What Are You Looking For? Find it Here • • • • • • Dell™ Product Information Guide Warranty information Terms and Conditions (U.S.
What Are You Looking For? Find it Here • Service Tag and Express Service Code • Microsoft Windows License Label Service Tag and Microsoft Windows License These labels are located on your computer. • Use the Service Tag to identify your computer when you use support.dell.com or contact technical support. • Enter the Express Service Code to direct your call when contacting technical support.
What Are You Looking For? Find it Here • How to use Windows XP • Documentation for my computer • Documentation for devices (such as a modem) Windows Help and Support Center 1 Click the Start button and click Help and Support. 2 Type a word or phrase that describes your problem and click the arrow icon. 3 Click the topic that describes your problem. 4 Follow the instructions on the screen.
Finding Information
Setting Up and Using Your Computer Setting Up a Printer NOTICE: Complete the operating system setup before you connect a printer to the computer. See the documentation that came with the printer for setup information, including how to: • Obtain and install updated drivers. • Connect the printer to the computer. • Load paper and install the toner or ink cartridge. • Contact the printer manufacturer for technical assistance. Printer Cable Your printer connects to your computer with a USB cable.
Connecting a USB Printer NOTE: You can connect USB devices while the computer is turned on. 1 Complete the operating system setup, if you have not already done so. 2 Install the printer driver if necessary. See the documentation that came with your printer. 3 Attach the USB printer cable to the USB connectors on the computer and the printer. The USB connectors fit only one way.
For information on installing a Media Card Reader, see "Installing a Media Card Reader" on page 83. xD-Picture Card and SmartMedia (SMC) CompactFlash Type I and II (CF I/II) and MicroDrive Card Memory Stick (MS/MS Pro) SecureDigital Card (SD)/ MultiMediaCard (MMC) To use the Media Card Reader: 1 Check the media or card to determine the proper orientation for insertion. 2 Slide the media or card into the appropriate slot until it is completely seated in the connector.
Changing the Display Settings 1 After you connect the TV, turn on the computer. The Microsoft® Windows® desktop displays on the monitor. 2 Enable clone mode or extended desktop mode in the display settings. • In clone mode, the monitor and TV display the same image. • In extended desktop mode, you can drag objects from one screen to the other, effectively doubling the amount of viewable work space.
Network Setup Wizard The Microsoft® Windows® XP operating system provides a Network Setup Wizard to guide you through the process of sharing files, printers, or an Internet connection between computers in a home or small office. 1 Click the Start button, point to All Programs→ Accessories→ Communications, and then click Network Setup Wizard. 2 On the welcome screen, click Next. 3 Click Checklist for creating a network.
If you do not have an MSN Explorer or AOL icon on your desktop or if you want to set up an Internet connection with a different ISP: 1 Save and close any open files, and exit any open programs. 2 Click the Start button and click Internet Explorer. The New Connection Wizard appears. 3 Click Connect to the Internet. 4 In the next window, click the appropriate option: • If you do not have an ISP and want to select one, click Choose from a list of Internet service providers (ISPs).
4 Press the eject button or gently push in the tray. To format CDs for storing data, to create music CDs, or to copy CDs, see the CD software that came with your computer. NOTE: Ensure that you follow all copyright laws when you create CDs.
A CD player includes the following basic buttons: Play. Move backward within the current track. Pause. Move forward within the current track. Stop. Go to the previous track. Eject. Go to the next track. A DVD player includes the following basic buttons: Stop. Play. Fast forward. Pause. Fast reverse. Go to the next title or chapter. Go to the previous title or chapter. For more information on playing CDs or DVDs, click Help on the CD or DVD player (if available).
Adjusting the Volume NOTE: When the speakers are muted, you do not hear the CD or DVD playing. 1 Click the Start button, point to All Programs → Accessories→ Entertainment, and then click Volume Control. 2 In the Volume Control window, click and drag the bar in the Volume Control column and slide it up or down to increase or decrease the volume. For more information on volume control options, click Help in the Volume Control window.
NOTE: Most commercial DVDs have copyright protection and cannot be copied using Sonic DigitalMedia. 1 Click the Start button, point to All Programs→ Sonic→ DigitalMedia Projects, and then click Copy. 2 Under the Copy tab, click Disc Copy. 3 To copy the CD or DVD: • If you have one CD or DVD drive, ensure that the settings are correct and click the Disc Copy button. The computer reads your source CD or DVD and copies the data to a temporary folder on your computer hard drive.
Media Type Read Write Rewritable DVD+R Yes Yes No DVD-R Yes Yes No DVD+RW Yes Yes Yes DVD-RW Yes Yes Yes DVD+R DL Yes Yes No DVD-R DL Maybe No No DVD-RAM Maybe No No Helpful Tips • Use Microsoft® Windows® Explorer to drag and drop files to a CD-R or CD-RW only after you start Sonic DigitalMedia and open a DigitalMedia project. • Use CD-Rs to burn music CDs that you want to play in regular stereos. CD-RWs do not play in most home or car stereos.
Power Management The Microsoft® Windows® XP power management features can reduce the amount of electricity your computer uses when it is on and you are not using it. You can reduce power to just the monitor or the hard drive, or you can use standby mode or hibernate mode to reduce power to the entire computer. When the computer exits from a power conservation mode, the Windows desktop is restored to the state it was in before it entered the mode.
Because hibernate mode requires a special file on your hard drive with enough disk space to store the contents of the computer memory, Dell creates an appropriately sized hibernate mode file before shipping the computer to you. If the computer’s hard drive becomes corrupted, Windows XP recreates the hibernate file automatically. Power Options Properties Define your standby mode settings, hibernate mode settings, and other power settings in the Power Options Properties window.
Advanced Tab The Advanced tab allows you to: • Place the power options icon in the Windows taskbar for quick access. • Set the computer to prompt you for your Windows password before the computer exits from standby mode or hibernate mode. • Program the power button to activate standby mode, activate hibernate mode, or turn off the computer. To program these functions, click an option from the corresponding drop-down menu and click OK.
Enabling the QRT Feature in System Setup The QRT drivers must be installed before this feature becomes active. These drivers are installed when this option is ordered. Also, Quick Resume is enabled in system setup when this feature is ordered. 1 Enter system setup (see page 100). 2 Press the arrow keys to highlight the Power Management menu option and press to access the menu. 3 Press the up- and down-arrow keys to highlight the Quick Resume option and press to access the menu.
To determine if your computer is using Hyper-Threading technology: 1 Click the Start button, right-click My Computer, and then click Properties. 2 Click Hardware and click Device Manager. 3 In the Device Manager window, click the plus (+) sign next to Processors. If Hyper-Threading is enabled, the processor is listed twice. You can enable or disable Hyper-Threading through system setup. For more information on accessing system setup, see page 100.
Solving Problems Troubleshooting Tips Follow these tips when you troubleshoot your computer: • If you added or removed a part before the problem started, review the installation procedures and ensure that the part is correctly installed. • If a peripheral device does not work, ensure that the device is properly connected. • If an error message appears on the screen, write down the exact message. This message may help technical support personnel diagnose and fix the problem(s).
TE S T T H E D R I V E — • Insert another floppy disk, CD, or DVD to eliminate the possibility that the original one is defective. • Insert a bootable floppy disk and restart the computer. NOTE: This system supports an optional USB floppy drive. C L E A N T H E D R I V E O R D I S K — See page 108. CHECK THE CABLE CONNECTIONS R U N T H E H A R D W A R E TR O U B L E S H O O T E R — See page 51. R U N T H E D E L L D I A G N O S T I C S — See page 48.
Hard drive problems RUN CHECK DISK — 1 Click the Start button and click My Computer. 2 Right-click Local Disk C:. 3 Click Properties. 4 Click the Tools tab. 5 Under Error-checking, click Check Now. 6 Click Scan for and attempt recovery of bad sectors. 7 Click Start. E-Mail, Modem, and Internet Problems CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide. NOTE: Connect the modem to an analog telephone jack only.
VE R I F Y T H A T T H E M O D E M I S C O M M U N I C A T I N G W I T H W I N D O W S — 1 Click the Start button and click Control Panel. 2 Click Printers and Other Hardware. 3 Click Phone and Modem Options. 4 Click the Modems tab. 5 Click the COM port for your modem. 6 Click Properties, click the Diagnostics tab, and then click Query Modem to verify that the modem is communicating with Windows. If all commands receive responses, the modem is operating properly.
N O N - S YS T E M D I S K E R R O R — Remove the floppy disk from the drive and restart your computer. NOTE: This system supports an optional USB floppy drive. N O T E N O U G H M E M O R Y O R R E S O U R C E S . C L O S E S O M E P R O G R A M S A N D T R Y A G A I N — Close all windows and open the program that you want to use. In some cases, you might have to restart your computer to restore computer resources. If so, run the program that you want to use first.
E N S U R E T H A T T H E IEEE 1394 D E V I C E I S R E C O G N I Z E D B Y W I N D O W S — 1 Click the Start button and click Control Panel. 2 Click Printers and Other Hardware. If your IEEE 1394 device is listed, Windows recognizes the device. I F Y O U H A V E P R O B L E M S W I T H A D E L L IEEE 1394 D E V I C E — Contact Dell (see page 111). I F Y O U H A V E P R O B L E M S W I T H A N O N -D E L L IEEE 1394 D E V I C E — Contact the manufacturer of the IEEE 1394 device.
The computer stops responding NOTICE: You might lose data if you are unable to perform an operating system shutdown. TU R N T H E C O M P U T E R O F F — If you are unable to get a response by pressing a key on your keyboard or moving your mouse, press and hold the power button for at least 8 to 10 seconds until the computer turns off. Then restart your computer. A program stops responding END THE PROGRAM — 1 Press simultaneously. 2 Click Applications.
Other software problems CHECK THE SOFTWARE DOCUMENTATION OR CONTACT THE SOFTWARE MANUFACTURER FOR TROUBLESHOOTING INFORMATION — • Ensure that the program is compatible with the operating system installed on your computer. • Ensure that your computer meets the minimum hardware requirements needed to run the software. See the software documentation for information. • Ensure that the program is installed and configured properly. • Verify that the device drivers do not conflict with the program.
IF YOU EXPERIENCE OTHER MEMORY PROBLEMS — • Reseat the memory modules (see page 66) to ensure that your computer is successfully communicating with the memory. • Ensure that you are following the memory installation guidelines (see page 65). • Your computer supports DDR2 memory. For more information about the type of memory supported by your computer, see "Memory" on page 95. • Run the Dell Diagnostics (see page 48).
Network Problems CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide. C H E C K T H E N E T W O R K C A B L E C O N N E C T O R — Ensure that the network cable is firmly inserted into both the network connector on the back of the computer and the network jack.
I F T H E P O W E R L I G H T I S O F F — The computer is either turned off or is not receiving power. • Reseat the power cable into both the power connector on the back of the computer and the electrical outlet. • If the computer is plugged into a power strip, ensure that the power strip is plugged into an electrical outlet and that the power strip is turned on. Also bypass power protection devices, power strips, and power extension cables to verify that the computer turns on properly.
CHECK THE PRINTER CABLE CONNECTIONS — • See the printer documentation for cable connection information. • Ensure that the printer cables are securely connected to the printer and the computer (see page 13). TE S T T H E E L E C T R I C A L O U T L E T — Ensure that the electrical outlet is working by testing it with another device, such as a lamp.
VE R I F Y T H A T T H E S C A N N E R I S R E C O G N I Z E D B Y M I C R O S O F T W I N D O W S — 1 Click the Start button, click Control Panel, and then click Printers and Other Hardware. 2 Click Scanners and Cameras. If your scanner is listed, Windows recognizes the scanner. R E I N S T A L L T H E S C A N N E R D R I V E R — See the scanner documentation for instructions.
RUN THE SPEAKER DIAGNOSTICS — SEE YOUR SPEAKER DOCUMENTATION FOR MORE INFORMATION. R E I N S T A L L T H E S O U N D D R I V E R — See page 50. R U N T H E H A R D W A R E TR O U B L E S H O O T E R — See page 51. No sound from headphones C H E C K T H E H E A D P H O N E C A B L E C O N N E C T I O N — Ensure that the headphone cable is securely inserted into the headphone connector (see page 57).
TE S T T H E E L E C T R I C A L O U T L E T — Ensure that the electrical outlet is working by testing it with another device, such as a lamp. C H E C K T H E D I A G N O S T I C L I G H T S — See page 45. If the screen is difficult to read C H E C K T H E M O N I T O R S E T T I N G S — See the monitor documentation for instructions on adjusting the contrast and brightness, demagnetizing (degaussing) the monitor, and running the monitor self-test.
Solving Problems
Troubleshooting Tools Diagnostic Lights CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide. To help you troubleshoot a problem, your computer has four lights labeled "1," "2," "3," and "4" on the front panel (see page 57). When the computer starts normally, the lights flash. If the computer malfunctions, the color and sequence of the lights identify the problem.
Light Pattern Problem Description Suggested Resolution A possible graphics card failure has occurred. • If the computer has a graphics card, remove the card, reinstall it (see page 68), and then restart the computer. • If the problem still exists, install a graphics card that you know works and restart the computer. • If the problem persists or the computer has integrated graphics, contact Dell (see page 111). A possible floppy or hard drive failure has Reseat all power and data cables and occurred.
Light Pattern Problem Description A possible expansion card failure has occurred. Suggested Resolution 1 Determine if a conflict exists by removing a card (not a graphics card) (see page 68) and restarting the computer. 2 If the problem persists, reinstall the card that you removed, remove a different card, and then restart the computer. 3 Repeat this process for each card. If the computer starts normally, troubleshoot the last card removed from the computer for resource conflicts (see page 51).
Dell Diagnostics CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide. When to Use the Dell Diagnostics If you experience a problem with your computer, perform the checks in "Solving Problems" on page 29 and run the Dell Diagnostics before you contact Dell for technical assistance. NOTICE: The Dell Diagnostics works only on Dell™ computers. 1 Turn on (or restart) your computer.
NOTE: The Service Tag for your computer is located at the top of each test screen. If you contact Dell, technical support will ask for your Service Tag. 3 If you run a test from the Custom Test or Symptom Tree option, click the applicable tab described in the following table for more information. Tab Function Results Displays the results of the test and any error conditions encountered. Errors Displays error conditions encountered, error codes, and the problem description.
If you experience a problem with any device, identify whether the driver is the source of your problem and, if necessary, update the driver. Windows XP 1 Click the Start button and click Control Panel. 2 Under Pick a Category, click Performance and Maintenance. 3 Click System. 4 In the System Properties window, click the Hardware tab. 5 Click Device Manager. 6 Scroll down the list to see if any device has an exclamation point (a yellow circle with a [!]) on the device icon.
3 Click the Hardware tab and click Device Manager. 4 Double-click the type of device for which you are installing the driver. 5 Double-click the name of the device for which you are installing the driver. 6 Click the Driver tab and click Update Driver. 7 Click Install from a list or specific location (Advanced) and click Next. 8 Click Browse and browse to the location to which you previously extracted the driver files. 9 When the name of the appropriate driver appears, click Next.
NOTICE: Make regular backups of your data files. System Restore does not monitor your data files or recover them. NOTE: The procedures in this document were written for the Windows default view, so they may not work if you set your Dell™ computer to the Windows Classic view. Creating a Restore Point 1 Click the Start button and click Help and Support. 2 Click System Restore. 3 Follow the instructions on the screen.
Undoing the Last System Restore NOTICE: Before you undo the last system restore, save and close all open files and exit any open programs. Do not alter, open, or delete any files or programs until the system restoration is complete. 1 Click the Start button, point to All Programs→ Accessories→ System Tools, and then click System Restore. 2 Click Undo my last restoration and click Next.
5 When prompted, click Finish to reboot the computer. NOTE: Do not manually shut down the computer. Click Finish and let the computer completely reboot. 6 When prompted, click Yes. The computer restarts. Because the computer is restored to its original operating state, the screens that appear, such as the End User License Agreement, are the same ones that appeared the first time the computer was turned on. 7 Click Next. The System Restore screen appears and the computer restarts.
Removing and Installing Parts Before You Begin This chapter provides procedures for removing and installing the components in your computer. Unless otherwise noted, each procedure assumes that the following conditions exist: • You have performed the steps in "Turning Off Your Computer" on page 55 and "Before Working Inside Your Computer" on page 55. • You have read the safety information in your Dell™ Product Information Guide.
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its edges or by its metal mounting bracket. Hold a component such as a processor by its edges, not by its pins. NOTICE: Only a certified service technician should perform repairs on your computer.
Front and Back View of the Computer Front View NOTE: The front-panel door does not close when you are using certain Flash Media or IEEE 1394, USB, or headphone connectors. 12 11 10 1 2 9 8 7 6 5 3 4 1 CD/DVD drive eject button Press this button to eject a CD/DVD from the drive. 2 CD/DVD drive-activity light The drive activity light is on when the computer reads data from the CD or DVD drive.
3 USB 2.0 connectors (2) Use the front USB connectors for devices that you connect occasionally, such as joysticks or cameras (see "System Setup" on page 99 for more information on booting to a USB device). It is recommended that you use the back USB connectors for devices that typically remain connected, such as printers and keyboards. 4 IEEE 1394 connector Attach high-speed serial multimedia devices, such as digital video cameras.
Back View 1 2 3 4 1 voltage selection switch See the safety instructions in the Product Information Guide for more information. 2 power connector Insert the power cable. 3 back panel connectors Plug IEEE 1394, USB and other devices into the appropriate connector. 4 card slots Access connectors for any installed PCI Express cards.
1 2 3 5 4 6 7 8 13 12 11 10 9 1 link integrity light • Green — A good connection exists between a 10-Mbps network and the computer. • Orange — A good connection exists between a 100-Mbps network and the computer. • Off — The computer is not detecting a physical connection to the network. 2 network adapter connector To attach your computer to a network or broadband device, connect one end of a network cable to either a network jack or your network or broadband device.
line-out connector 7 Use the green line-out connector to attach headphones and most speakers with integrated amplifiers. On computers with a sound card, use the connector on the card. 8 microphone/side surround sound connector Use the pink and silver connector to attach a personal computer microphone for voice or musical input into a sound or telephony program.
NOTICE: Ensure that you are working on a level, protected surface to avoid scratching either the computer or the surface on which it is resting. 5 Lay your computer on its side with the computer cover facing up. 6 Pull back the cover latch release on the top panel. security cable slot cover release latch computer cover 7 Locate the two hinge tabs on the bottom edge of the computer. 8 Grip the sides of the computer cover and pivot the cover up, using the bottom hinges as leverage points.
Inside View of Your Computer CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before opening the cover.
System Board Components internal speaker (SPKR) processor connector (CPU) password jumper (PSWD) power connector (ATXPWR1) processor fan connector (FAN) memory module connectors (2, 4) memory module connectors (1, 3) floppy drive connector (DSKT) battery socket (BATTERY) RTC reset jumper (RTCRST) PCI Express x16 connector (SLOT1) SATA connector (SATA0) PCI Express x1 connector (SLOT2) CD/DVD connector (IDE_OPT) front-panel IEEE 1394 connector (1394_FRONT) front-panel connector (FRONT PANEL) IEE
Memory You can increase your computer memory by installing memory modules on the system board. Your computer supports unbuffered, non-ECC, DDR2 memory. NOTE: Buffered memory is not supported on this computer. DDR2 Memory Overview DDR2 memory modules should be installed in pairs of matched memory size, speed, and technology. If the DDR2 memory modules are not installed in matched pairs, the computer will continue to operate, but with a slight reduction in performance.
matched pair of memory modules in DIMM connectors 1 and 2 (white securing clips) matched pair of memory modules in DIMM connectors 3 and 4 (black securing clips) NOTE: Memory purchased from Dell is covered under your computer warranty. NOTICE: If you remove your original memory modules from the computer during a memory upgrade, keep them separate from any new modules that you may have, even if you purchased the new modules from Dell.
4 Press out the securing clip at each end of the memory module connector. memory connector closest to processor securing clips (2) connector 5 Align the notch on the bottom of the module with the crossbar in the connector. notch memory module cutouts (2) crossbar NOTICE: To avoid damage to the memory module, press the module straight down into the connector while you apply equal force to each end of the module. 6 Insert the module into the connector until the module snaps into position.
7 Replace the computer cover, (see page 93). NOTICE: To connect a network cable, first plug the cable into the network device and then plug it into the computer. 8 Connect your computer and devices to electrical outlets, and turn them on. 9 Right-click the My Computer icon and click Properties. 10 Click the General tab. 11 To verify that the memory is installed correctly, check the amount of memory (RAM) listed.
Your Dell™ computer provides the following slots for PCI Express cards: • One PCI Express x16 card slot • One PCI Express x1 card slot NOTE: The slots for the PCI Express x16 and PCI Express x1 cards are half-height slots. PCI Express x16 card PCI Express x1 card PCI Express x16 card slot PCI Express x1 card slot If you are installing or replacing a PCI Express card, follow the procedures in the next section. If you are removing but not replacing a card, see "Removing a PCI Express Card" on page 72.
retention arm tab PCI Express card edge connector securing slot card connector securing tab 3 If you are installing a new card, remove the filler bracket to create a card-slot opening. Then continue with step 5. 4 If you are replacing a card that is already installed in the computer, remove the card. If necessary, disconnect any cables connected to the card. Grasp the card by its top corners, and ease it out of its connector. 5 Prepare the card for installation.
8 Place the card in the connector and press down firmly. Ensure that the card is fully seated in the slot. card not fully seated card fully seated bracket within slot bracket caught outside of slot 9 Before you close the card retention door, ensure that: • The tops of all cards and filler brackets are flush with the alignment bar. • The notch in the top of the card or filler bracket fits around the alignment guide.
10 Close the card retention door by snapping it into place. retention arm PCI Express card edge connector card connector NOTICE: Do not route card cables over or behind the cards. Cables routed over the cards can prevent the computer cover from closing properly or cause damage to the equipment. 11 Connect any cables that should be attached to the card. See the documentation that came with the card for information about the card’s cable connections.
4 If you are removing the card permanently, install a filler bracket in the empty card-slot opening. NOTE: Installing filler brackets over empty card-slot openings is necessary to maintain FCC certification of the computer. The brackets also keep dust and dirt out of your computer. 5 Replace the computer cover (see page 93), reconnect the computer and devices to electrical outlets, and then turn them on. 6 Uninstall the card’s driver.
Drive Interface Connectors Most interface connectors are keyed for correct insertion; that is, a notch or a missing pin on one connector matches a tab or a filled-in hole on the other connector. Serial ATA cables go to the pin-1 end of the connector. The pin-1 end of a connector on a board or a card is usually indicated by a silk-screened “1” printed directly on the board or card. NOTICE: When you connect an IDE interface cable, do not place the colored stripe away from pin 1 of the connector.
Like IDE connectors, the serial ATA interface connectors are keyed for correct insertion; that is, a notch or a missing pin on one connector matches a tab or a filled-in hole on the other connector. Hard Drive CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide. CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before removing the cover.
Removing a Hard Drive 1 Follow the procedures in "Before You Begin" on page 55. 2 Press in on the blue tabs on each side of the drive and slide the drive up and out of the computer. tabs (2) hard drive 3 Disconnect the power and hard-drive cable from the drive.
Installing a Hard Drive 1 Unpack the replacement hard drive, and prepare it for installation. 2 Check the documentation for the drive to verify that it is configured for your computer. NOTE: If your replacement hard drive does not have the plastic guide bracket attached, remove the bracket from the old drive by unsnapping it from the drive. Snap the bracket onto the new drive. tabs (2) drive drive bracket 3 Connect the power and hard-drive cables to the drive.
5 Gently slide the drive into place until you hear a click or feel the drive securely installed. tabs (2) hard drive 6 Replace the computer cover (page 93). NOTICE: To connect a network cable, first plug the cable into the network wall jack and then plug it into the computer. 7 Connect your computer and devices to electrical outlets, and turn them on. See the documentation that came with the drive for instructions on installing any software required for drive operation.
CD/DVD drive drive release latch NOTE: The interface cable is held in place by the metal drive bracket and does not need to be removed from the drive. 4 Disconnect the interface cable from the interface cable connector on the system board (see page 64).
Installing a CD/DVD Drive 1 Unpack the drive and prepare it for installation. Check the documentation that accompanied the drive to verify that the drive is configured for your computer. If you are installing an IDE drive, configure the drive for the cable select setting. 2 Connect the interface cable to the interface cable connector on the system board. See "System Board Components" on page 64. interface cable interface cable connector 3 Slide the drive into place.
4 Check all cable connections, and fold cables out of the way to provide airflow for the fan and cooling vents. 5 Replace the computer cover (see page 93). 6 Connect your computer and devices to their electrical outlets, and turn them on. 7 See the documentation that came with the drive for instructions on installing any software required for drive operation. 8 Enter system setup (see page 99) and select the appropriate Drive option.
Removing a Media Card Reader 1 Follow the procedures in "Before You Begin" on page 55. 2 Remove the CD/DVD drive (see page 78). 3 Remove the hard drive (see page 76). 4 Disconnect the interface cable from the back of the Media Card Reader and from the Media Card Reader connector on the system board (see page 64).
5 Pull up on the drive release latch and slide the Media Card Reader towards the back of the computer. Then, lift to remove the drive from the computer. Media Card Reader drive release latch Installing a Media Card Reader 1 Follow the procedures in "Before You Begin" on page 55. 2 Remove the Media Card Reader from its packaging.
3 Slide the drive into place until you hear a click or feel the drive securely installed. 4 Connect the interface cable to the back of the Media Card Reader and to the Media Card Reader connector on the system board.
5 Replace the CD/DVD drive (see page 80). 6 Replace the hard drive (see page 77). 7 Replace the computer cover (see page 93). NOTICE: To connect a network cable, first plug the cable in to the network device and then plug it in to the computer. 8 Connect your computer and devices to their electrical outlets, and turn them on. See the documentation that came with the drive for instructions on installing any software required for drive operation.
floppy drive drive release latch 5 Disconnect the interface cable from the system board (see page 64). NOTE: The interface cable is held in place by the metal drive bracket and does not need to be removed from the drive.
Installing a Floppy Drive NOTE: The interface cable is held in place by the metal drive bracket and does not need to be removed from the drive. 1 Follow the procedures in "Before You Begin" on page 55. 2 Gently slide the drive into place until you hear a click or feel the drive securely installed. 3 Attach the interface cable to the system board (see page 64).
cable release tab interface cable edge connector interface cable 4 Check all cable connections, and fold cables out of the way to provide airflow for the fan and cooling vents. 5 Replace the CD/DVD drive (see page 80). 6 Replace the computer cover (see page 93). NOTICE: To connect a network cable, first plug the cable in to the network device and then plug it in to the computer. 7 Connect your computer and devices to their electrical outlets, and turn them on.
Modem CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. NOTICE: Before you remove or install the modem, make sure to disconnect all telephone and network cables from your computer. NOTICE: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer’s electronic components.
2 Remove the existing modem: a Disconnect the modem cable from the modem. b Use a small Phillips screwdriver to remove the two screws securing the modem to the system board, and set the screws aside. c Pull straight up on the attached pull-tab to lift the modem out of its connector on the system board. NOTICE: The connectors are keyed to ensure correct insertion. If you feel resistance, check the connectors and realign the card.
screw (from the back of the computer) external modem connector 6 To install a new modem cable and external modem connector: a Attach the modem cable to the external modem connector. a Align the external connector with the slot on the back on the computer. b Replace the screw that secures the external modem connector in place. c Carefully route the cable wire and re-connect the modem cable to the modem. 7 Replace the computer cover (see page 93).
CAUTION: A new battery can explode if it is incorrectly installed. Replace the battery only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’s instructions. Replacing the Battery NOTE: For information regarding the type of coin-cell battery, see "Power" on page 98. 1 Record all the screens in system setup (see page 99) so that you can restore the correct settings in step 9. 2 Follow the procedures in "Before You Begin" on page 55.
10 Properly dispose of the old battery. See the Product Information Guide for battery disposal information. Replacing the Computer Cover CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide. 1 Ensure that all cables are connected, and fold cables out of the way. Gently pull the power cables toward you so that they do not get caught underneath the drives. 2 Ensure that no tools or extra parts are left inside the computer.
Removing and Installing Parts
Appendix Specifications Processor Processor types Intel® Pentium® 4 5XXX and 6XXX processors with HyperThreading technology Pentium D 8XXX dual core processors (no Hyper-Threading) Intel Celeron® D processors Level 1 (L1) cache 16 KB for Pentium 4 5XXX and 6XXX processors and Celeron D processors 2 x 16 KB for Pentium D 8XXX dual core processors Level 2 (L2) cache 1 MB for Pentium 4 5XXX processors 2 MB for Pentium 4 6XXX processors 2 x 1 MB for Pentium D 8XXX processors 128 KB for Celeron D processors
Computer Information Chipset Intel 945G Express DMA channels eight Interrupt levels 24 BIOS chip (NVRAM) 4 Mb NIC integrated network interface capable of 10/100-Mbps communication System clock 800-MHz data rate Video Type Intel integrated Graphics Media Accelerator (GMA) 950 Audio Type Sigmatel STAC9220 Expansion Bus Bus type PCI Express x1 and x16 Bus speed PCI Express: x1 slot bidirectional speed: 500 MB/s x16 slot bidirectional speed: 8 GB/sec PCI Express: connector one x1 connector
Connectors External connectors: IEEE 1394 one 6-pin powered back-panel connector one 6-pin powered front-panel connector Video 15-hole D-SUB connector USB two front-panel and five back-panel USB 2.
Controls and Lights Power control push button Power light green light — Blinking green in sleep state; solid green for power-on state. amber light — Blinking amber indicates a problem with an installed device; solid amber indicates an internal power problem (see "Power Problems" on page 38). Hard-drive access light green Link integrity light (on integrated network adapter) green light — A good connection exists between a 10-Mbps network and the computer.
Physical Height 31.8 cm (12.5 inches) Width 9.4 cm (3.7 inches) Depth 36.8 cm (14.5 inches) Weight 6.89 kg (15.2 lb) Environmental Temperature: Operating 10° to 35°C (50° to 95°F) Storage –40° to 65°C (–40° to 149°F) Relative humidity 20% to 80% (noncondensing) Maximum vibration: Operating 0.25 G at 3 to 200 Hz at 0.5 octave/min Storage 0.5 G at 3 to 200 Hz at 1 octave/min Maximum shock: Operating bottom half-sine pulse with a change in velocity of 50.
Before you use system setup, it is recommended that you write down the system setup screen information for future reference. NOTICE: Unless you are an expert computer user, do not change the settings for this program. Certain changes can make your computer work incorrectly. Entering System Setup 1 Turn on (or restart) your computer. 2 When the blue DELL™ logo appears, press immediately.
Options List — This field appears on the left side of the system setup window. The field is a scrollable list containing features that define the configuration of your computer, including installed hardware, power conservation, and security features. Option Field — This field contains information about each option. In this field you can view your current settings and make changes to your settings. Use the right- and left-arrow keys to highlight an option. Press to make that selection active.
System Setup Options NOTE: Depending on your computer, BIOS version, and installed devices, the items listed in this section may not appear, or may not appear exactly as listed. System System Info Lists system information such as the computer name, the BIOS version number and date, system tags, and other system-specific information. NOTE: The system name listed in the BIOS may not appear exactly as the name that appears on the computer or in the computer’s documentation.
USB Controller Set to On (default) so that USB devices will be detected and supported in the operating system. The No Boot option enables a USB controller, but it does not recognize a USB storage device. Video Primary Video This setting specifies which video controller is primary when two video controllers are present on the computer. Video Memory Size Use this option to select 8 MB (default) or 1 MB of system memory for an integrated video controller.
Admin Password This option provides restricted access to the computer's system setup in the same way that access to the computer can be restricted with the System Password option. NOTE: To delete a password, enter the old password and press two times. System Password Displays the current status of the system's password security feature and allows a new system password to be assigned and verified. Password Status This option locks the system password field with the setup password.
POST Hotkeys This option allows you to specify the function keys to display on the screen when the computer starts. Keyboard Errors This option disables or enables keyboard error reporting when the computer starts. Boot Sequence This feature allows you to change the boot sequence for devices. NOTICE: If you modify any boot sequence settings, save the new settings to avoid losing the changes. Option Settings • Diskette Drive — The computer attempts to boot from the floppy drive.
4 Select a device and press . For example, if you are booting to a USB memory key, highlight USB Flash Device and press . NOTE: To boot to a USB device, the device must be bootable. To make sure your device is bootable, check the device documentation. NOTE: You can also change the boot sequence using the Boot Sequence options in the System Setup Options (see page 102). Changing Boot Sequence for Future Boots 1 Enter system setup (see page 100).
Clearing Forgotten Passwords CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide. 1 Follow the procedures in "Before You Begin" on page 55. 2 To clear the password, remove the jumpers from pins 1 and 2. 3 Replace the computer cover (see "Replacing the Computer Cover" on page 93). 4 Connect your computer and monitor to electrical outlets, and turn them on.
NOTICE: To connect a network cable, first plug the cable into the network device and then plug it into the computer. 11 Connect your computer and devices to electrical outlets, and turn them on. Clearing CMOS Settings CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide. 1 Follow the procedures in "Before You Begin" on page 55. 2 Remove the hard drive (see page 76).
NOTICE: Do not wipe the display screen with any soap or alcohol solution. Doing so may damage the antiglare coating. • To clean your monitor screen, lightly dampen a soft, clean cloth with water. If possible, use a special screen-cleaning tissue or solution suitable for the monitor’s antistatic coating. • Wipe the keyboard, computer, and plastic part of the monitor with a soft cleaning cloth moistened with a solution of three parts water and one part dishwashing detergent.
Dell Technical Support Policy (U.S. Only) Technician-assisted technical support requires the cooperation and participation of the customer in the troubleshooting process and provides for restoration of the operating system, software programs, and hardware drivers to the original default configuration as shipped from Dell, as well as the verification of appropriate functionality of the computer and all Dell-installed hardware.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1 This device may not cause harmful interference. 2 This device must accept any interference received, including interference that may cause undesired operation. NOTICE: The FCC regulations provide that changes or modifications not expressly approved by Dell Inc. could void your authority to operate this equipment.
For specific web addresses for your country, find the appropriate country section in the table below. NOTE: Toll-free numbers are for use within the country for which they are listed. NOTE: In certain countries, technical support specific to Dell XPS portable computers is available at a separate telephone number listed for participating countries.
Country (City) International Access Code Country Code City Code Australia (Sydney) Department Name or Service Area, Website and E-Mail Address Area Codes, Local Numbers, and Toll-Free Numbers E-mail (Australia): au_tech_support@dell.com International Access Code: 0011 E-mail Customer Care (Australia and New Zealand): apcustserv@dell.
Country (City) International Access Code Country Code City Code Department Name or Service Area, Website and E-Mail Address Area Codes, Local Numbers, and Toll-Free Numbers Belgium (Brussels) Website: support.euro.dell.com International Access Code: 00 Country Code: 32 E-mail for French-speaking Customers: support.euro.dell.
Country (City) International Access Code Country Code City Code Department Name or Service Area, Website and E-Mail Address Cayman Islands General Support Chile (Santiago) Sales, Customer Support, and Technical Support Area Codes, Local Numbers, and Toll-Free Numbers 1-800-805-7541 toll-free: 1230-020-4823 Country Code: 56 City Code: 2 China (Xiamen) Technical Support website: support.dell.com.cn Country Code: 86 Technical Support E-mail: cn_support@dell.
Country (City) International Access Code Country Code City Code Colombia Department Name or Service Area, Website and E-Mail Address Area Codes, Local Numbers, and Toll-Free Numbers General Support 980-9-15-3978 Costa Rica General Support 0800-012-0435 Czech Republic (Prague) Website: support.euro.dell.com International Access Code: 00 E-mail: czech_dell@dell.
Country (City) International Access Code Country Code City Code Department Name or Service Area, Website and E-Mail Address Area Codes, Local Numbers, and Toll-Free Numbers France (Paris) (Montpellier) Website: support.euro.dell.com International Access Code: 00 E-mail: support.euro.dell.
Country (City) International Access Code Country Code City Code Department Name or Service Area, Website and E-Mail Address Area Codes, Local Numbers, and Toll-Free Numbers Greece Website: support.euro.dell.com International Access Code: 00 E-mail: support.euro.dell.
Country (City) International Access Code Country Code City Code Department Name or Service Area, Website and E-Mail Address Area Codes, Local Numbers, and Toll-Free Numbers Ireland (Cherrywood) Website: support.euro.dell.com International Access Code: 16 E-mail: dell_direct_support@dell.com Country Code: 353 Technical Support for XPS portable computers only 1850 200 722 City Code: 1 Technical Support for all other Dell computers 1850 543 543 U.K. Technical Support (dial within U.K.
Country (City) International Access Code Country Code City Code Department Name or Service Area, Website and E-Mail Address Japan (Kawasaki) Website: support.jp.dell.
Country (City) International Access Code Country Code City Code Latin America Department Name or Service Area, Website and E-Mail Address Area Codes, Local Numbers, and Toll-Free Numbers Customer Technical Support (Austin, Texas, U.S.A.) 512 728-4093 Customer Service (Austin, Texas, U.S.A.) 512 728-3619 Fax (Technical Support and Customer Service) (Austin, Texas, U.S.A.) 512 728-3883 Sales (Austin, Texas, U.S.A.) 512 728-4397 SalesFax (Austin, Texas, U.S.A.
Country (City) International Access Code Country Code City Code Mexico Department Name or Service Area, Website and E-Mail Address Customer Technical Support International Access Code: 00 Country Code: 52 Area Codes, Local Numbers, and Toll-Free Numbers 001-877-384-8979 or 001-877-269-3383 Sales 50-81-8800 or 01-800-888-3355 Customer Service 001-877-384-8979 or 001-877-269-3383 Main 50-81-8800 or 01-800-888-3355 Montserrat General Support toll-free: 1-866-278-6822 Netherlands Antilles General
Country (City) International Access Code Country Code City Code Department Name or Service Area, Website and E-Mail Address New Zealand E-mail (New Zealand): nz_tech_support@dell.com International Access Code: 00 E-mail Customer Care (Australia and New Zealand): apcustserv@dell.
Country (City) International Access Code Country Code City Code Department Name or Service Area, Website and E-Mail Address Portugal Website: support.euro.dell.com International Access Code: 00 E-mail: support.euro.dell.com/pt/en/emaildell/ Country Code: 351 Technical Support Customer Care Sales Fax Area Codes, Local Numbers, and Toll-Free Numbers 707200149 800 300 413 800 300 410 or 800 300 411 or 800 300 412 or 21 422 07 10 21 424 01 12 Puerto Rico General Support 1-800-805-7545 St.
Country (City) International Access Code Country Code City Code Department Name or Service Area, Website and E-Mail Address Area Codes, Local Numbers, and Toll-Free Numbers South Africa (Johannesburg) Website: support.euro.dell.com International Access Code: E-mail: dell_za_support@dell.
Country (City) International Access Code Country Code City Code Department Name or Service Area, Website and E-Mail Address Area Codes, Local Numbers, and Toll-Free Numbers Sweden (Upplands Vasby) Website: support.euro.dell.com International Access Code: 00 E-mail: support.euro.dell.
Country (City) International Access Code Country Code City Code Department Name or Service Area, Website and E-Mail Address Area Codes, Local Numbers, and Toll-Free Numbers Thailand Website: support.ap.dell.
Country (City) International Access Code Country Code City Code Department Name or Service Area, Website and E-Mail Address Area Codes, Local Numbers, and Toll-Free Numbers U.S.A.
Index A audio.
Index E e-mail problems, 31 End User License Agreement, 9 installing parts before you begin, 55 recommended tools, 55 turning off your computer, 55 error messages diagnostic lights, 45 Internet connection, about, 17 connection, options, 17 connection, setting up, 17 problems, 31 F K floppy drive installing, 87 removing, 85 keyboard problems, 34 ergonomics information, 9 L H hard drive installing, 77 problems, 31 removing, 76 hardware Dell Diagnostics, 48 Hardware Troubleshooter, 51 Help and
O operating system restoring, 51-52 P password clearing, 107 jumper, 107 PC Restore, 51-52 PCI Express cards installing, 69 removing, 72 playing CDs, 18 DVDs, 18 power conserving, 24 hibernate mode, 24, 26 managing, 24 options, 25 options, advanced, 26 options, hibernate, 26 options, schemes, 25 problems, 38 standby mode, 24 power light conditions, 38 printer cable, 13 connecting, 13 problems, 39 setting up, 13 USB, 14 problems battery, 29 blue screen, 35 CD drive, 30 CD/DVD-RW drive, 30 computer crashes,
Index speaker problems, 41 volume, 41 specifications audio, 96 computer information, 96 connectors, 97 controls and lights, 98 drives, 96 environmental, 99 expansion bus, 96 memory, 95 physical, 99 power, 98 processor, 95 technical, 95 video, 96 standby mode, 24 support contacting Dell, 110-111 policy, 110 system board, 64 System Restore, 51-52 system setup entering, 100 options, 102 screens, 100 132 Index T W technical support policy, 110 warranty information, 9 troubleshooting Dell Diagnostic