APC Mach 5 v2 Quick Installation Guide Revision 1.0 13 September 2011 Copyright © 2011 Deliberant www.deliberant.
Copyright © 2011 Deliberant This user’s guide and the software described in it are copyrighted with all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form by any means without the written permission of Deliberant. Notice Deliberant reserves the right to change specifications without prior notice.
Quick Installation Guide Contents Contents Copyright ............................................................................................................................................. 2 Notice .................................................................................................................................................. 2 Trademarks .........................................................................................................................................
Quick Installation Guide Introduction Introduction FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Quick Installation Guide Introduction Safety This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this manual and of the computer manufacturer must therefore be allowed at all times to ensure the safe use of the equipment.
Quick Installation Guide About this Guide About this Guide Purpose The purpose of this guide is to provide a quick and easy explanation of getting started with the APC Mach 5. This is only a starter guide and full documentation may be found at our online wiki: http://wiki.deliberant.com/. Prerequisite Skills and Knowledge To use this document effectively, you should have a working knowledge of Local Area Networking (LAN) concepts and wireless Internet access infrastructures.
Quick Installation Guide Installation Installation This chapter provides installation instructions for the hardware components of the APC Mach 5.
Quick Installation Guide Installation Hardware Introduction The APC Mach 5 unit is housed in an aluminum enclosure. The panel of the APC Mach 5 v2 unit contains: Data/Power connection in the form of passive PoE through standard Ethernet cable LED indicators Mounting hardware Grounding stud Figure 2 – General View of the APC Mach 5 v2 Unit The APC Mach 5 has label with following information: Figure 3 – APC Mach 5 v2 Label The label of the APC Mach 5 v2 contains: Model name.
Quick Installation Guide Installation LEDs The APC Mach 5 v2 has 6 LEDs located on the side panel: power, LAN and 4 RSSI LEDs (refer at the Figure 2 – General View of the APC Mach 5 v2 Unit for details). The various states of the LEDs indicate different connection operations as follows: LED Color Status Indication Power Green On APC Mach 5 unit is active/working Off No power on APC Mach 5 unit. On LAN connection exists. Blinking Indicates the traffic on LAN interface.
Quick Installation Guide Installation Step 3. Attach the mounting bracket and the pole clamp with the bolts and nuts. The clamp’s orientation will differ according the pole’s diameter as displayed below: Step 4. Connect power adapter into PoE injector together with UTP cables. Step 5. Power-up the unit. The green Power LED must be on (refer at the respective section LEDs).
Quick Installation Guide Installation Step 4. Attach the following part of the mounting bracket to the APC Mach 5 v2 unit with 4 screws as displayed below: Step 5 Attach the second part of the mounting bracket to the wall using screws (not included) as displayed below: Step 6 Connect the mounting bracket parts together as displayed below and tighten up: It is recommended not to tighten the units to its mounting brackets until the alignment process of the antenna is complete. Step 7.
Quick Installation Guide Access the APC Mach 5 v2 Access the APC Mach 5 v2 The first connection to the APC Mach 5 v2 can be made using a standard Ethernet cable connected directly to your PC. See next sections for the instructions on how to access the APC Mach 5 management interfaces. Connection via WEB Browser The default IP address of the APC Mach 5 v2 is 192.168.2.66 with a subnet mask of 255.255.255.0. Step 1. Configure your PC with a static IP address on the 192.168.2.0 subnet with mask 255.255.
Quick Installation Guide Resetting to Factory Defaults APC Mach 5 v2 has the capability of being reset to defaults by pinging the device with a certain packet size when the device is booting. During the startup of the device, when the drivers of the ethernet interfaces are loaded, the reset daemon is started. The daemon suspends startup process for 3 seconds and waits for ICMP "echo request" packet of length 369 bytes. If the packet received, the reset daemon sets the device to default configuration.
