APC 5M V2 Quick Installation Guide Revision 1.2 24 October 2011 Copyright © 2011 Deliberant www.deliberant.
Copyright © 2011 Deliberant This user’s guide and the software described in it are copyrighted with all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form by any means without the written permission of Deliberant. Notice Deliberant reserves the right to change specifications without prior notice.
Quick Installation Guide Contents Contents Copyright ............................................................................................................................................. 2 Notice .................................................................................................................................................. 2 Trademarks .........................................................................................................................................
Quick Installation Guide Introduction Introduction FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Quick Installation Guide Introduction CE Mark Warning This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. R&TTE Compliance Statement This equipment complies with all the requirements of the Directive 1999/5/EC of the European Parliament and the Council of 9 March 1999 on Radio Equipment and Telecommunication Terminal Equipment and the Mutual Recognition of their Conformity (R&TTE).
Quick Installation Guide About this Guide About this Guide Prerequisite Skills and Knowledge To use this document effectively, you should have a working knowledge of Local Area Networking (LAN) concepts and wireless Internet access infrastructures. Definitions, Acronyms and Abbreviations The following typographic conventions and symbols are used throughout this document: Additional information that may be helpful but which is not required. Important information that should be observed.
Quick Installation Guide Installation Installation This chapter provides installation instructions for the hardware components of the APC 5M V2.
Quick Installation Guide Installation Hardware Introduction APC 5M V2 is housed in a plastic enclosure ensuring a reliable sealing in a wide range of temperature and has two external N-connectors for external antenna.
Quick Installation Guide Installation LEDs The APC 5M V2 has 6 LEDs located on the side panel: power, LAN and 4 RSSI. The various states of the LEDs indicate different connection operations as follows: LED Color Power Green LAN RSSI (1, 2, 3, 4) deliberant Green Status Indication On APC 5M V2 is active/working Off No power on APC 5M V2 On LAN connection exists. Blinking Indicates the traffic on LAN interface. Off No LAN connection.
Quick Installation Guide Installation Assembling and Mounting the APC 5M V2 The APC 5M V2 units are supplied with mounting hardware for pole with diameters in the range 40mm to 64mm installations. Follow the next two sections for APC 5M V2 mounting instructions on a preferable surface. Pole Mounting Step 1. Make sure that the APC 5M V2 unit is powered-off. Step 2.
Quick Installation Guide Step 5. Installation Connect Ethernet cable into the APC 5M V2 then insert a rubber gasket (item H in the Figure 1 – APC 5M V2 Package Contents) into CAT5 Ethernet connector gland and tighten with gland cap (item G in the Figure 1 – APC 5M V2 Package Contents) as displayed below: It is recommended to use shielded STP Ethernet cable to reduce exposure of the electromagnetic noise. Step 6.
Quick Installation Guide Installation It is recommended to use shielded STP Ethernet cable to reduce exposure of the electromagnetic noise. Step 4. Attach the unit to a mounting plate and push it downwards until it clicks into position: Step 5. After attaching the APC 5M V2 to the mounting plate, fasten the unit to the bottom near the CAT5 Ethernet plug using screw (item E in the Figure 1 – APC 5M V2 Package Contents.) Step 6. Power-up the unit.
Quick Installation Guide Access the APC 5M V2 Access the APC 5M V2 The first connection to the APC 5M V2 can be made using a standard Ethernet cable connected directly to your PC. See next sections for the instructions on how to access the APC 5M V2 management interfaces. Connection via WEB Browser The default IP address of the APC 5M V2 is 192.168.2.66 with a subnet mask of 255.255.255.0. Step 1. Configure your PC with a static IP address on the 192.168.2.0 subnet with mask 255.255.255.0.
Quick Installation Guide Access the APC 5M V2 Resetting to Factory Defaults APC 5M V2 has the capability of being reset to defaults by pinging the device with a certain packet size when the device is booting. During the startup of the device, when the drivers of the ethernet interfaces are loaded, the reset daemon is started. The daemon suspends startup process for 3 seconds and waits for ICMP "echo request" packet of length 369 bytes.
