APC 5Mi V2 Quick Installation Guide Revision 1.0 15 July 2011 Copyright © 2011 Deliberant www.deliberant.
Copyright © 2011 Deliberant This user’s guide and the software described in it are copyrighted with all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form by any means without the written permission of Deliberant. Notice Deliberant reserves the right to change specifications without prior notice.
Quick Installation Guide Contents Contents Copyright ............................................................................................................................................. 2 Notice .................................................................................................................................................. 2 Trademarks .........................................................................................................................................
Quick Installation Guide Introduction Introduction FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Quick Installation Guide Introduction CE Mark Warning This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. R&TTE Compliance Statement This equipment complies with all the requirements of the Directive 1999/5/EC of the European Parliament and the Council of 9 March 1999 on Radio Equipment and Telecommunication Terminal Equipment and the Mutual Recognition of their Conformity (R&TTE).
About this Guide Quick Installation Guide About this Guide Prerequisite Skills and Knowledge To use this document effectively, you should have a working knowledge of Local Area Networking (LAN) concepts and wireless Internet access infrastructures. Definitions, Acronyms and Abbreviations The following typographic conventions and symbols are used throughout this document: Additional information that may be helpful but which is not required. Important information that should be observed.
Quick Installation Guide Installation Installation This chapter provides installation instructions for the hardware components of the APC 5Mi V2. Package Contents The figure below displays APC 5Mi V2 package contents. Figure 1 – APC 5Mi V2 Package Contents Item Component Name Quantity A APC 5Mi V2 Quick Installation Guide 1 B APC 5Mi V2 enclosure 1 C Omni antenna 2 D PoE injector 1 E Power adapter 1 If any of these items are missing or damaged, please contact your reseller.
Installation Quick Installation Guide The APC 5Mi V2 has a label with following information: Figure 3 – APC 5Mi V2 Label The label of the APC 5Mi V2 contains: Model name. The official model name is APC 5Mi V2. Serial Number Radio MAC address LAN MAC address FCC ID: UB8-APC5MIV2 IC ID: 6607-APC5MIV2 LEDs The APC 5Mi V2 has 6 LEDs located on the side panel: power, LAN and 4 RSSI LEDs (refer at the Figure 2 – APC 5Mi V2 Overview for details).
Quick Installation Guide Installation Mounting the APC 5Mi V2 on the Wall The indoor unit APC 5Mi V2 unit can be mounted on a wall easy. Follow the steps for APC 5Mi V2 installation on a wall: Step 1. Attach the unit by a two screws on a wall and push it downwards until it clicks into position: Step 2. Connect omni antennas (item C in the Figure 1 – APC 5Mi V2 Package Contents), Ethernet cable and power adapter (item D and E in the Figure 1 – APC 5Mi V2 Package Contents), to the APC 5Mi V2: Step 3.
Quick Installation Guide Access the APC 5Mi V2 Access the APC 5Mi V2 The first connection to the APC 5Mi V2 can be made using a standard Ethernet cable connected directly to your PC. See next sections for the instructions on how to access the APC 5Mi V2 management interfaces. Connection via WEB Browser The default IP address of the APC 5Mi V2 is 192.168.2.66 with a subnet mask of 255.255.255.0. Step 1. Configure your PC with a static IP address on the 192.168.2.0 subnet with mask 255.255.255.0.
Quick Installation Guide Access the APC 5Mi V2 Resetting to Factory Defaults The APC 5Mi V2 device has 2 options how to reset device to factory defaults: Reset button (refer at the Figure 2 – APC 5Mi V2 Overview). Press and hold the Reset button for 1 second to reboot the controller; press and hold the Reset button for more than 5 seconds to set the controller to factory defaults.
