APC 5M-90 V2 Quick Installation Guide Revision 1.0 15 July 2011 ŽƉLJƌŝŐŚƚ Ξ 2011 Deliberant www.deliberant.
Copyright 2011 Deliberant TKLV XVHU¶V JXLGH DQG WKH VRIWZDUH GHVFULEHG LQ LW DUH FRS\ULJKWHG ZLWK DOO ULJKWV UHVHUYHG 1R SDUW RI this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form by any means without the written permission of Deliberant. Notice Deliberant reserves the right to change specifications without prior notice.
Quick Installation Guide Contents ŽŶƚĞŶƚƐ Copyright ............................................................................................................................................. 2 Notice .................................................................................................................................................. 2 Trademarks .........................................................................................................................................
Quick Installation Guide Introduction /ŶƚƌŽĚƵĐƚŝŽŶ FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Quick Installation Guide Introduction CE Mark Warning This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. R&TTE Compliance Statement This equipment complies with all the requirements of the Directive 1999/5/EC of the European Parliament and the Council of 9 March 1999 on Radio Equipment and Telecommunication Terminal Equipment and the Mutual Recognition of their Conformity (R&TTE).
Quick Installation Guide About this Guide ďŽƵƚ ƚŚŝƐ 'ƵŝĚĞ Prerequisite Skills and Knowledge To use this document effectively, you should have a working knowledge of Local Area Networking (LAN) concepts and wireless Internet access infrastructures. Definitions, Acronyms and Abbreviations The following typographic conventions and symbols are used throughout this document: Additional information that may be helpful but which is not required. Important information that should be observed.
Quick Installation Guide Installation /ŶƐƚĂůůĂƚŝŽŶ This chapter provides installation instructions for the hardware components of the APC 5M-90 V2. Package Contents The figure below displays APC 5M-90 V2 package contents.
Quick Installation Guide Installation Hardware Introduction APC 5M-90 V2 is housed in a plastic ultrasonically welded enclosure, ensuring a reliable sealing in a wide range of temperature and has an integrated 20dBi sector antenna. Figure 2 ± APC 5M-90 V2 Overview The side panel of the APC 5M-90 V2 contains: Ethernet/Power connection in the form of passive PoE through standard Ethernet cable. 6 LEDs: Power, LAN activity and 4 LEDs for device RSSI level indication.
Quick Installation Guide Installation LEDs The APC 5M-90 V2 has 6 LEDs located on the side panel: power, LAN and 4 RSSI LEDs (refer at the Figure 2 ± APC 5M-90 V2 Overview for details). The various states of the LEDs indicate different connection operations as follows: LED Color Status Indication Power Green On APC 5M-90 V2 is active/working Off No power on APC 5M-90 V2 On LAN connection exists. Blinking Indicates the traffic on LAN interface. Off No LAN connection.
Quick Installation Guide Step 4. Installation Attach the mounting hardware to the device: first fix mounting hardware part 1 with four Hex bolts M4x5 (items C and L in the Figure 1 ± APC 5M-90 V2 Package Contents), then attach the mounting hardware part 2 and fix it with four Hex bolts M5x10 (items D and K in the Figure 1 ± APC 5M-90 V2 Package Contents). It is recommended not to tighten the unit to its mounting bracket until the alignment process of the antenna is complete. Step 4.
Quick Installation Guide Installation Step 5. Ground the APC 5M-90 V2 unit. The unit must be properly grounded to protect against lightning. The grounding wire must be attached to the grounding stud and tightened with the nut (item H in the Figure 1 ± APC 5M-90 V2 Package Contents): Step 6. Connect AC adapter into PoE injector (items F and G in the Figure 1 ± APC 5M-90 V2 Package Contents) together with UTP cables as displayed in the picture below: Step 7. Power-up the unit.
Quick Installation Guide Access the APC 5M-90 V2 ĐĐĞƐƐ ƚŚĞ W ϱD-ϵϬ sϮ The first connection to the APC 5M-90 V2 can be made using a standard Ethernet cable connected directly to your PC. See next sections for the instructions on how to access the APC 5M-90 V2 management interfaces. Connection via WEB Browser The default IP address of the APC 5M-90 V2 is 192.168.2.66 with a subnet mask of 255.255.255.0. Step 1. Configure your PC with a static IP address on the 192.168.2.0 subnet with mask 255.255.255.
Quick Installation Guide Access the APC 5M-90 V2 Resetting to Factory Defaults APC 5M-90 V2 has the capability of being reset to defaults by pinging the device with a certain packet size when the device is booting. During the device startup, after the Ethernet interface drivers are loaded, the reset daemon starts. The daemon suspends startup process for 3 seconds and waits for ICMP "echo request" packet in length of 369 bytes.
