APC 2M, 5M, 5M V2, 2M-8, 5M-12, 5M-12 V2 Quick Installation Guide Revision 1.0 24 November 2011 Copyright © 2011 Deliberant www.deliberant.
Copyright © 2011 Deliberant This user’s guide and the software described in it are copyrighted with all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form by any means without the written permission of Deliberant. Notice Deliberant reserves the right to change specifications without prior notice.
Contents Copyright ............................................................................................................................................. 2 Notice .................................................................................................................................................. 2 Trademarks ......................................................................................................................................... 2 CONTENTS .................................
Introduction FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Safety This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this manual and of the computer manufacturer must therefore be allowed at all times to ensure the safe use of the equipment.
About this Guide Prerequisite Skills and Knowledge To use this document effectively, you should have a working knowledge of Local Area Networking (LAN) concepts and wireless Internet access infrastructures. Definitions, Acronyms and Abbreviations The following typographic conventions and symbols are used throughout this document: Additional information that may be helpful but which is not required. Important information that should be observed.
Installation This chapter provides installation instructions for the hardware components of the APC 2M, APC 5M, APC 5M V2, APC 2M-8, APC 5M-12, APC 5M-12 V2.
Hardware Introduction The APC is housed in a plastic enclosure ensuring a reliable sealing in a wide range of temperature and has two external N-connectors for external antenna.
LEDs The APC has 5 LEDs located on the side panel: power, LAN and 4 RSSI LEDs (refer at the Figure 2 – APC 2M, APC 5M, APC 5M V2, APC 2M-8, APC 5M-12, APC 5M-12 V2 Overview for details). The various states of the LEDs indicate different connection operations as follows: LED Color Status Indication Power Green On APC is active/working Off No power on APC On LAN connection exists. Blinking Indicates the traffic on LAN interface. Off No LAN connection.
Step 4. Attach the unit to a mounting plate and push it downwards until it clicks into position: Step 5.
Step 3. Connect Ethernet cable into the APC then insert a rubber gasket (item H in the Figure 1 – APC 2M, APC 5M, APC 5M V2, APC 2M-8, APC 5M-12, APC 5M-12 V2 Package Contents) into CAT5 Ethernet connector gland and tighten with gland cap (item G in the Figure 1 – APC 2M, APC 5M, APC 5M V2, APC 2M-8, APC 5M-12, APC 5M-12 V2 Package Contents) as displayed below: It is recommended to use shielded STP Ethernet cable to reduce exposure of the electromagnetic noise. Step 4.
Access the APC The first connection to the APC can be made using a standard Ethernet cable connected directly to your PC. See next sections for the instructions on how to access the APC management interfaces. Connection via WEB Browser The default IP address of the APC 2M, APC 5M, APC 5M V2, APC 2M-8, APC 5M-12, APC 5M-12 V2 is 192.168.2.66 with a subnet mask of 255.255.255.0. Step 1 Configure your PC with a static IP address on the 192.168.2.0 subnet with mask 255.255.255.0.
Resetting to Factory Defaults APC 2M, APC 5M, APC 5M V2, APC 2M-8, APC 5M-12, APC 5M-12 V2 has the capability of being reset to defaults by pinging the device with a certain packet size when the device is booting. During the startup of the device, when the drivers of the Ethernet interfaces are loaded, the reset daemon is started. The daemon suspends startup process for 3 seconds and waits for ICMP "echo request" packet of length 369 bytes.
