OZONE GENERATORS FOR SPAS INSTALLATION & OPERATION MANUAL For Models: SpaEclipse™, SpaEclipse™ Dual Voltage, CDS-16, ZO-300/302, ZO-301 & Platinum EPA Estab. No. 071472-CA-001 4-1223-01 Rev.
IMPORTANT SAFETY INSTRUCTIONS Proper installation and usage of your DEL Spa Ozone Generator is your responsibility. Read and follow this Owner’s Manual carefully for important installation, operation and safety information. Basic safety precautions should always be followed, including but not limited to the following: 1. READ AND FOLLOW ALL INSTRUCTIONS. 2. All electrical connections should be made by a qualified electrician. 3. Follow all applicable electrical codes. 4.
Spa Ozone Generator Installation & Operation Manual Table of Contents Installation Instructions 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11.
Installation Instructions 1. How the DEL Spa Ozone Generator Works a. DEL Ozone Generators produce ozone gas which is introduced to the spa water through suction created by the spa. Tubing is used to connect the Ozone Generator to an injector or a vacuum port provided by the spa manufacturer. The injector or port are vacuum sources used to pull the ozone gas out of the Ozone Generator and into the water. At no time should water come in contact with the Ozone Generator.
Spa Ozone Generator Installation & Operation Manual 5 CAUTION: DO NOT TWIST cartridges while pushing them together. Twisting will damage the OZONE GENERATOR which could lead to premature failure. Attach the two cartridges by securing the bonding plate to the lamp cartridge. Use the included self-tapping screw and star washer.
5. Mounting a. Note: SpaEclipse™ Dual Voltage models are equipped with a voltage selector switch on the back of the unit. Set this switch to the appropriate voltage (as indicated on the switch) prior to installation. Once the proper voltage has been selected (comes preset at 230V), cover the switch with the label provided to prevent tampering (refer to Figure 3). Figure 3 Switch Cover Label Application for SpaEclipse™ Dual Voltage Cover Label Voltage Selector b.
Spa Ozone Generator Installation & Operation Manual Figure 4 Typical Injection System DEL Ozone Generator Spa Wall Return Fitting Check Valve Gas Flow Injector Pump c. Cut the tubing near the vacuum source, slide hose clamps on each end and install the check valve in the tubing. Observe the flow arrow on the check valve and ensure that the flow direction is into the vacuum source. d. Secure all tubing connections with the hose clamps. 8. Electrical a.
10. Installation Complete a. Once properly installed, the Ozone Generator requires no further user operation. It will operate automatically with the spa system. 11. Maintenance a. To ensure the highest degree of sanitation at all times, refer to the chart below. Renew your Spa Ozone Generator as needed with a renewal kit.
Spa Ozone Generator Installation & Operation Manual 9 Troubleshooting SYMPTOM: Cloudy water condition even though the unit appears to be operating properly PROBABLE CAUSE: 1. Unit and pump not operating long enough 2. Total alkalinity not correct 3. pH not correctly balanced 4. Not enough suction 5. Dirty, loose or cracked filter 6. Metals or minerals in the water CORRECTIVE ACTION: 1A. Increase operating time (min. 6 hours is recommended) 2A. Adjust total alkalinity between 80 and 150 ppm 3A.
DEL Ozone - ONE YEAR LIMITED WARRANTY The limited warranty set forth below applies to products manufactured by DEL Ozone - and sold by DEL Ozone or its authorized dealers. This limited warranty is given only to the first retail purchaser of such products and is not transferable to any subsequent owners or purchasers of such products.
DEL Ozone WARRANTY REGISTRATION CARD Product Serial Date: Fill out completely and return to DEL Ozone within ten (10) days of purchase.
PO Box 4509, San Luis Obispo, Ca. 93401 800.676.1335 www.delozone.