Menu Functions 2. Unlock the screen by pressing each front button from left to right to unlock the remote screen. Once unlocked, screen will stay active for 2 minutes before going into sleep mode. 124 3. Place the pump and remote within 2 in (50 mm) of each other during the pairing process. 4. If your pump's serial number does not show up on screen after a minute, press and hold the pump’s blue button for 10 seconds to activate pairing mode. Then, check the screen again for your pump serial number.
Menu Functions 5. On the remote, use to highlight the pump's serial number and press DKPI-09153-001-Rev. 1.4 . 6. After selecting your pump serial number you will be prompted to confirm the selected pump. Press to confirm.
Menu Functions A Pairing To... message displays. If pairing fails, see "Pairing Failed Attention Alarm" on page 166 126 7. Upon successful pairing the Paired Pump message displays. Press . DKPI-09153-001-Rev. 1.
Menu Functions Walkaway Attention Alarm To help you avoid forgetting your remote, setting this feature will let you know that you may have left your remote behind. The Walkaway Attention Alarm feature can be set to go off between 1 and 120 minutes. Turn ON Walkaway Attention Alarm: 1. Press the side button to wake up the remote. 2. Unlock the screen by pressing each front button from left to right. 3. Use the down arrow 4. Press . 5. Press the down arrow Alarm:OFF. 6. Press to scroll to Setup.
Menu Functions Turn OFF Walkaway Attention Alarm: 1. Press the side button to wake up the remote. the screen by pressing each 2. Unlock front button from left to right. 3. Use the down arrow 4. Press . 5. Press the down arrow Alarm:ON. 10. Press the front button under ON to turn ON the Walkaway Attention Alarm feature. 11. Press 6. Press to scroll to Setup. to Walkaway . to accept your selection. A Sending request to the pump message displays. 128 DKPI-09153-001-Rev. 1.
The Screen Timeout feature allows you to set the time before the remote's screen will sleep. 1. Press the side button to wake up the remote. 2. Unlock the screen by pressing each front button from left to right. 3. Use the down arrow 4. Press . 7. Press the front button under OFF to turn OFF the Walkaway Attention Alarm feature. 5. Press the down arrow 8. Press 6. Press to accept your selection. to scroll to Setup. to Screen Timeout. . A Sending request to the pump message displays.
Menu Functions 7. Press the up and down arrows select one of four times: • One minute • Two minutes • Five minutes • Ten minutes to 8. Press to accept your selection. Any time the remote has not been used and the programmed screen timeout minutes have passed, you will need to press the side button to wake up the remote. 130 Remote Audio The Remote Audio feature controls the feedback and volume options for the remote. Feedback Options 1. Press the side button to wake up the remote. 2.
1. Press the side button to wake up the remote. 2. Unlock the screen by pressing each front button from left to right. 3. Use the down arrow to scroll to Setup. 4. Press . 5. Press the down 7. The Feedback option is already highlighted. 8. Press . arrow to Remote Audio. 6. Press . 9. Press the up and down arrows to select one of three feedback options: • Audio and Vibration • Audio Only • Vibration Only 10. Press to accept your selection. DKPI-09153-001-Rev. 1.
Menu Functions 7. Press the down arrow option. 8. Press 132 . to the Volume 9. Press the up and down arrows select one of five volume levels. 10. Press to to accept your selection. DKPI-09153-001-Rev. 1.
Menu Functions Change Rate Passcode The Change Rate Passcode is Off by default. When turned On a passcode will be required to change the rate. Turn ON Change Rate Passcode 1. Press the side button to wake up the remote. 2. Unlock the screen by pressing each front button from left to right. 3. Use the down arrow 4. Press . DKPI-09153-001-Rev. 1.4 to scroll to Setup. 5. Press the down arrow 6. Press to Passcode: OFF. .
Menu Functions 7. Press the front button under ON. 134 8. Use the up and down arrows through the first digit selection. to scroll DKPI-09153-001-Rev. 1.
Menu Functions 9. When you have the desired number press the right arrow . 10. Repeat Step 8 and Step 9 for the remaining three digits. 11. Confirm the passcode by repeating Step 8 and Step 9 to enter your new four digit passcode. DKPI-09153-001-Rev. 1.4 A message displays that the Passcode is Enabled. 12. Press to return to the Setup Menu.
Menu Functions Turn OFF Change Rate Passcode 1. Press the side button to wake up the remote. 2. Unlock the screen by pressing each front button from left to right. 3. Use the down arrow to scroll to Setup. 4. Press . 5. Press the down arrow to Passcode: ON. 6. Press . 7. Press the front button under OFF. 136 8. Use the up and down arrows to enter the first digit of your current passcode. 9. When finished entering the number press the right arrow . 10.
If you are asked to turn off all electronic devices during a commercial flight, follow the steps to put the device into airplane mode. 1. Press the side button to wake up the remote. 2. Unlock the screen by pressing each front button from left to right. 3. Use the down arrow A message displays that the Passcode is Disabled. 11. Press to return to the Setup Menu.
Menu Functions 7. Press to enable airplane mode. A Sending request to the pump message displays. 138 A Press and hold pump button to exit message displays. The pump will continue to deliver medication even when the remote is in airplane mode. DKPI-09153-001-Rev. 1.
Menu Functions 9. Verify the remote displays Delivering on the Home screen. When the use of electronics is cleared during a commercial flight you can exit airplane mode. 8. You will need to press and hold the blue pump button until after you hear the four-tone delivering sound to exit airplane mode. DKPI-09153-001-Rev. 1.
Menu Functions Factory Reset Remote Factory Reset A Factory Reset should not be performed unless directed by your specialty pharmacist. 1. Press the side button to wake up the remote. 2. Unlock the screen by pressing each front button from left to right. 3. Use the down arrow 4. Press . 5. Press the down arrow Reset. 6. Press to scroll to Setup. to scroll to Factory 1. Press to factory reset the remote. . You will need to select whether you want to reset the remote or the pump.
Menu Functions Pump Factory Reset A Reset the Remote to defaults? Pump will be disconnected! message displays. 1. Press the down arrow 2. Press to confirm or to cancel. A Remote will restart when complete message displays. 2. Press to highlight Pump. to factory reset the pump. The remote will display Searching until the pump is paired to the remote. See "Pair to a Spare Remote" on page 123. DKPI-09153-001-Rev. 1.