GE Contactless Smart Card Reader Model 240 and 245 Installation Guide 791 Park of Commerce Boulevard Suite 100 Boca Raton, Florida 33487 (561) 998-6100 Part Number: 460563001B January 2003
This document contains proprietary information of General Electric Company, USA and is furnished to its customer solely to assist that customer in the installation, testing, operation, and/or maintenance of the equipment described. This document shall not be reproduced in whole or in part nor shall its contents be disclosed to any third party without the written approval of GE Industrial Systems.
Contents Introduction ....................................................................................................... 1 Product Overview ............................................................................................. 5 Features ................................................................................................. 5 Access Control System Compatibility .............................................. 5 Installation.................................................................
Figures Figure 1: Figure 2: Figure 3: GE Contactless Smart Card Reader Model 240 ............ 1 GE Contactless Smart Card Reader Model 245 ............ 2 GE Model 24x Reader Backplate (includes tamper switch magnet) ................................... 3 Figure 4: Isolation Spacer ............................................................. 4 Figure 5: GE Model 24x Backplate and Snap-on cover ................ 7 Figure 6: Back-to-Back/Center-to-Center Installation....................
FIGURE 3: GE Model 24x Reader Backplate (includes tamper switch magnet) Note: Mounting holes fit standard US single-width electrical box and standard European (EMEA) electrical box hole patterns. An Isolation Spacer (shown in Figure 4) may be used to improve the readrange distance when mounting to metal surfaces. Dimensions are the same as the Reader Backplate.
FIGURE 4: Isolation Spacer 4 GE Contactless Smart Card Reader Model 24x
Product Overview Features • Universal compatibility with all ISO 15963 and ISO 14443A credentials (badges, disc tags, and key fobs). • Supervised four-state (open, closed, wire cut, and wire short) monitoring for door contacts, REX (request to exit). • Electrical protection (reverse polarity diode protection on power lines).
microcontrollers must be specially configured to receive the incoming 16digit BID numbers, and convert them into the proper 12-digit BID format. To make a Secure Perfect 4.0 or higher system compatible with the complete line of GE Contactless Smart Card Reader, do the following: • Install Secure Perfect Edition, 4.0 or higher • Load the Secure Perfect Update CD in the server CD drive • Locate the Badge Formats folder • In the Badge Formats folder, locate the 15693.REG file • Double-click the 15693.
Installation FIGURE 5: GE Model 24x Backplate and Snap-on cover The front cover snaps into place. To remove the cover, use a small flatblade screwdriver to pry the cover from the backplate, using either of the two provided locations on the vertical sides of the reader. Installation of the Model 245 is similar to that of the Model 240.
Installation Considerations 1. Installation of the GE Model 24x Reader on metal. Read-range reduction can be improved by adding Isolation Spacers (approximately 25% per plate). 2. Installation of two Model 24x Smart Card Readers side-by-side. Read range is not affected if the center-to-center distance between two readers is equal to or greater than four inches (101.60 mm). If the distance between the two readers is less than four inches (101.
When installing two readers back-to-back on a wall that will separate the two readers by four inches (101.60 mm) or less, a metal plate (for example: Reader isolation plate, metal wall) must be placed between the readers. To obtain the maximum read range, mount each GE Model 24x Smart Card Reader onto one or more Isolation Spacers. Note: Two readers can simultaneously read the same badge or tag if the distance between the two readers is less than four inches (101.60 mm), back-to-back.
Wiring Table 2: Reader 12-Position Field Wiring Connector Pin 10 Definition 1 Micro control, reader beeper (option) 2 Ground 3 8 VDC to 30 VDC 4 Door contact 5 Reader Data 1 6 Exit request (REX) 7 Green LED 8 Micro control, red LED (option) 9 RS-485-B, reader firmware maintenance 10 RS-485-A, reader firmware maintenance 11 Reserved for future use 12 Reserved for future use GE Contactless Smart Card Reader Model 24x
Installation Notes (unless otherwise specified). All numbered items below are referenced on the appropriate wiring diagrams throughout this manual. 1. Fuse, power supply, door strike, protection device, and relay are provided by the installer. 2. The included 470 Ω ½-watt pull-up resistor must be installed at the microcontroller’s terminal block. The Micro PX-2000 and 8RP boards do not require this resistor. 3. Shielded cable is recommended in electrically noisy environments. 4.
Point-to-Point Wiring Diagrams FIGURE 7: GE Model 24x Reader Wiring Diagram to Micro/5 8RP 12 GE Contactless Smart Card Reader Model 24x
FIGURE 8: Model 24x Smart Card Reader Wiring Diagram to J-Box GE Contactless Smart Card Reader Model 24x 13
Table 3: 2RP Reader Switch Settings Reader Technology and Format Supervised F/2F SW-1 SW-2 ON OFF SW-3 SW-4 ON OFF Table 4: 2RP Reader Board Address Settings SW 1 Reader Board 5 6 SW 2 7 8 1 2 3 4 1 ON OFF OFF OFF ON OFF OFF OFF 2 OFF ON OFF OFF OFF ON OFF OFF 3 OFF OFF ON OFF OFF OFF ON OFF 4 OFF OFF OFF ON OFF OFF OFF ON Note: Switches SW2-5, 6, 7, and 8 are not used. Jumper W1 RN2 and RN5 (labeling) Set to 12 V Use 2k Ω (202) resistor packs.
Table 5: 8RP Reader Technology and Format Reader Technology and Format SW1-1 SW1-2 SW1-3 SW1-4 Supervised F/2F ON OFF ON OFF Table 6: 8RP Board Address Settings SW 1 Board Type 5 6 Standard ON Board 1a Does not apply. 7 ON Board 2b 8 ON OFF OFF ON OFF ON a. Readers 1 - 8 b. Readers 9 - 16 Note: the 8RP board appears to the Micro as four 2RP boards.
FIGURE 11: GE Model 24x Reader to Micro If using a J-Box relay as a dry contact, place a jumper across J4, pins 1 and 2 as shown in Figure 11 above. Connect the power supply in series with the door strike.
Troubleshooting If the operation of a component is in doubt, substitute a known-good component and retry the system. Always verify wiring against the provided wiring before powering up the system. Table 7: Error Conditions and Possible Solutions Condition Possible Solutions None of the LEDs are on. Present a known-good ISO 15963 or ISO 14443A type card to the reader while listening for the beeper. If the beeper sounds, the reader is faulty and should be replaced.
Condition Possible Solutions The green LED does not light, but the door strike unlocks the door when a valid ISO 15693 card is presented. Verify that the door strike is wired correctly. Refer to the appropriate wiring diagram. Green LED lights, but the door does not open. Verify correct door strike wiring and operation. The reader is functioning. If not, check that the blocking diode is functioning. If it is not, replace it.
Condition Possible Solutions The reader sounds a short triple beep every 30 seconds and the red LED flashes quickly (every 400 ms). Indicates a tamper violation. Ensure the reader is properly attached to its backplate. The red LED will continue to blink for 30 seconds. The reader is ready for use when the yellow LED is steadily on. The reader sounds a short triple beep every 5 seconds and the red LED also flashes every 5 seconds.
Technical Specifications • • • • • • Cable: Belden (shielded) 8777, 9873, 9773 Certifications: FCC Part 15; CE Mark, and UL 294 (pending) Color: Gray Dimensions with backplate (height/width/depth): 4.37” x 3.31” x 1.10” (110.99 x 84.07 x 27.
Regulatory Notices FCC Changes or modifications not expressly approved by GE-Interlogix for compliance could void the user’s authority to operate the equipment. FCC and CE Compliance. Shield grounds must be stripped back through the knockout hole (strain relief) and grounded to the external ground stud provided on the microcontroller.
CE Manufacturers Declaration of Conformity Manufacturer’s Name: GE Interlogix, CASI Manufacturer’s Address: 791 Park of Commerce Boulevard, Suite 100 Boca Raton, FL USA 33487 EU Representative: Interlogix Europe & Africa Excelsiorlaan 28 B- 1930 Zaventum Belgium Product Identification: Product: GE Interlogix, CASI Smart Card Reader Model Number: 240, 245 Brand: CASI Means of Conformity: • Hereby, GE Interlogix, CASI, declares that this equipment is in compliance with the essential requirements an
GE Contactless Smart Card Reader Model 24x 25
26 GE Contactless Smart Card Reader Model 24x
GE Contactless Smart Card Reader Model 24x 27
28 GE Contactless Smart Card Reader Model 24x