User's Manual

ManualsBrandsDeister Electronic ManualsElectronicsProximity Reader

GE-Interlogix-CASI

Model-240 Proximity Reader

9/17/2002

Page 1 of 4

Description

The GE-Interlogix-CASI Model 240 access control badge reader

is an ISO standard compliant, proximity technology badge

reader. The Model 240 reader will read ISO-14443 and ISO-

15693 badges and key tags. The reader’s aesthetically pleasing

contemporary design and light gray housing will complement

any decor.

Features:

• Compatible with Micro/5 2RP and 8RP controllers (not M/5-2SRP)

• Compatible with all Micro/PX(N)-2000 controllers

• Sealed electronics, suitable for outdoor installation

• Tamper switch protected

• Reads ISO-14443 and ISO-15693 access control badges and tags

• Reads badge or tag serial number, no memory sector records required

• User interface: 3-LEDs and beeper

• Fast field maintenance, field wiring plug

• Up to 4” read range (badge type and installation conditions dependent)

• 4-state input supervision of door contact & REX switch: opened, closed, cut, short

• Reader supervision: continuously monitored by the microcontroller

Specifications

• Mount: on single width USA or European style electrical box or directly on wall

• Material: ASA plastic housing; polyurethane encapsulated electronics

• Housing dimensions: 3.34 x 4.40 x 0.96 inch: (85 x 112 x 24.2 mm)

• Temperature range: -13 to 140 °F /-25 to +70 °C

• Power supply: 8VDC to.30 VDC @ <100 mA

• Electrical protection: Reverse polarity diode protection on power lines

• Data Lines: high-speed transient voltage suppressor diodes

• Protection type: IP 65 (IEC 529). Suitable for outdoor installation

• Frequency: 13.56 MHz

• Approvals: FCC,CE-EN 300 330

• Read distance: up to 2 inches ISO-14443 or up to 4 inches ISO-15693

• Microcontroller firmware versions: Picture Perfect 1.7 or greater recommended

• Interface: Supervised F/2F

• Electrical connection: 12 position plug-in strip connector with screw terminals

• Beeper: controlled by SF2F protocol

• Red LED: controlled by SF2F protocol

• Green LED: controlled by SF2F protocol

• Yellow LED: internal controlled

• RS-485 for reader firmware maintenance and configuration

• Casi pn: 430177001

Summary of content (4 pages)

PAGE 1
GE-Interlogix-CASI Model-240 Proximity Reader 9/17/2002 Description The GE-Interlogix-CASI Model 240 access control badge reader is an ISO standard compliant, proximity technology badge reader. The Model 240 reader will read ISO-14443 and ISO15693 badges and key tags. The reader’s aesthetically pleasing contemporary design and light gray housing will complement any decor.
PAGE 2
GE-Interlogix-CASI Model-240 Proximity Reader 9/17/2002 FCC Cautionary Comment Modifications to the Model-240 reader not expressly approved by GE-Interlogix may void the FCC approval. Model 240 Back plate Note: Mounting holes fit a standard US single width electrical box and standard European electrical box hole patterns.
PAGE 3
GE-Interlogix-CASI Model-240 Proximity Reader 9/17/2002 Installation Considerations 1) Installation of the Model 240 reader on metal The table below shows the expected read range reduction when a Model 240 reader is mounted onto a metal plate or wall. Distance Reading distance No metal plate 100 % 1.78 inch (4.5 cm) use 4 Surface 100% Mount Extension plates 1.06 inch, (2.7 cm) use 3 Surface 85 % Mount Extension plates 0.70 inch (1.8 cm) use 2 Surface 70 % Mount Extension plates 0.35 inch (0.
PAGE 4
GE-Interlogix-CASI Model-240 Proximity Reader 9/17/2002 3) Installation of two Model 240 readers back to back For proper operation, readers installed back-to-back must be separated by at least 3.2 inches (8cm). Attention Two readers may simultaneously read the same badge or tag if the distance between the two readers is less than 6-inches (15 cm), back-to-back.