3. Technical Data Dimensions: mm (inch) Operating temperature: °C (°F) Interface: Power supply: Operating frequency: Electrical connection: 3. Technische Daten Abmaße: mm Betriebstemperatur: °C Schnittstellen: Spannungsversorgung: Arbeitsfrequenz: Elektr. Anschluss: 3. Données Techniques Dimensions: mm Temp. de fonctionnement: °C Interface: Alimentation: Fréquence de fonctionnement: Connexions electriques: 29 x 15.5 x 11.5 (1.14 x 0.61 x 0.45) +5 ... +60 (+41 ... +140) RX/TX (3.3V TTL) 5 V/DC (3.3 to 5.
Modular approval FCC ID: IXLMBL1 In accordance with FCC part 15.249, the MBL1 is listed as a modular transmitter device. Conformément à la section 15.249 des règlements FCC, le module MBL1 est répertorié comme un dispositif émetteur modulaire. This module is evaluated for stand-alone use only. Finished products incorporating multiple transmitters must comply with colocation and RF exposure requirements in accordance with FCC multitransmitter product procedures.
the applicable individual technical rules as well as to the general conditions of operation in Sections 15.5, 15.15, and 15.29 to not cause interference. The operator of the host product will be obligated to stop operating the device until the interference has been corrected. d) The following test modes should be followed by the manufacturer to ensure that the module, when incorporated, meets all emissions requirements.
résultant ne dépasse pas les limites d'émissions parasites ou les limites de bande (par exemple, lorsqu'une antenne différente peut provoquer des émissions supplémentaires). b) Les tests doivent vérifier les émissions qui peuvent se produire en raison du mélange des émissions avec les autres émetteurs, des circuits numériques ou en raison des propriétés physiques du produit hôte (boîtier).
indicates the product includes a certified module. The label should state the following (or similar wording that conveys the same meaning): Contains FCC ID: IXLMBL1 OR This product contains FCC ID: IXLMBL1 The OEM must include the following statements on the exterior of the final product unless the product is too small (e.g. less than 4 x 4 inches): This device complies with Part 15 of the FCC Rules.
5.3 Product manual instructions This section applies to OEM final products containing the MBL1 module, subject to FCC compliance. The final product manual must contain the following statement (or a similar statement that conveys the same meaning): La présente section concerne les produits finis contenant le module MBL 1, assujettis aux normes FCC.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
6.1 Labeling instructions / Instructions d'étiquetage When integrating the MBL1 into the final product, the OEM must ensure that the IC labeling requirements are satisfied. A statement must be included on the exterior of the final product which indicates that the product includes a certified module.
Dans le cas où le produit finis d'un fabriquant OEM rentre dans les limites de la Classe B (résidentiel), les énoncés suivants doivent être inclus dans le manuel du produit finis: Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to RSS-210 of the IC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
In the case where an OEM seeks the lesser category of a Class A digital device for the final product, the following statement must be included in the final product manual: Dans le cas où le produit fini d'un sous-traitant rentre dans les limites imposées aux appareils numériques de classe A, les énoncés suivants doivent être inclus dans le manuel du produit finis: Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to RSS-210 of the IC Rules.
Germany: deister electronic GmbH Hermann-Bahlsen-Str. 11 30890 Barsinghausen Tel.: +49 (0) 51 05 - 51 61 11 Fax: +49 (0) 51 05 - 51 62 17 info.de@deister.com Benelux: deister electronic office Hendrik van Veldekesingel 150/56 OffiCenter 3500 Hasselt, Belgium Tel.: +32 (0) 15 – 48 02 15 Fax: +32 (0) 15 – 48 02 16 info.be@deister.com France: deister electronic france 29, rue Jean Rostand Parc Club Orsay Université 91400 ORSAY Tel.: +33 (0) 1 47 – 35 78 78 Fax: +33 (0) 1 47 – 35 92 59 info.fr@deister.