HANDHELD BHT, BHT lite, BHI, BHI Pro Manual - Draft V07/06/05
BiTech Handheld Manual -DRAFT - © Copyright 2005 by deister electronic GmbH All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without prior written permission of Agrident GmbH. Agrident GmbH reserves the right to make changes to any and all parts of this documentation without obligation to notify any person or entity of such changes.
BiTech Handheld Manual - DRAFT Contents 1 Introduction ..................................................................... 5 1.1 1.2 1.3 The 8 keys for the operation....................................................................................... 6 The status messages in the second line of the DISPLAY ................................................. 6 The acoustic signals ..................................................................................................
BiTech Handheld Manual -DRAFT - 4 deister electronic GmbH 30890 Barsinghausen Germany V07/06/05
BiTech Handheld Manual - DRAFT 1 Introduction The portable full-ISO BiTech readers are so small - they fit even into a shirt pocket - they have a very handy design and are easy to operate even under worse conditions. The readers are compatible to the ISO standard 11785 and read FDX-B and HDX. Tags with the widely used chip type H4102 can be read as well. The two HOTKEYES can be programmed individually and combined with a special action.
BiTech Handheld Manual -DRAFT Basic operation of BiTech readers 1.1 The 8 keys for the operation • • • • • • • • ON/OFF - Switch power on/off HOTKEY A Starts a READ and or additional functions HOTKEY B Starts a READ and or additional functions F – Switch into MENU modus C – In MENU modus one level up RETURN Conformation of changes in the MENU modus and one level down - SCROLL up Move or Value higher - SCROLL down Move or Value lower 1.
BiTech Handheld Manual - DRAFT 2 Operating the BiTech reader Before starting operation of the BiTech reader, the batteries being supplied separately have to be put in the battery case. In case that you would like to use other types of batteries, resp. rechargeable batteries, please read chapter 4.3.7 POWER MANAGER to set the battery type. Caution! An other battery type than it is chosen in the selection list of the power manager, might cause harm to the reader. 2.
BiTech Handheld Manual -DRAFT 2.4 No ID found If there is no transponder in the field of the antenna or no valid ID is received (e.g. a faulty transponder or too much noise). Display: NO TRANSPONDER Action stopped A new read could be started by pressing HOTKEY A or B.
BiTech Handheld Manual - DRAFT 3 DISPLAY and SAVE of an ID 3.1 Standard mode without ACTION CODE The ID will be displayed in the upper line. In SAVE MODE = ASK, in the second line SAVE? YES/NO will be displayed. 980 123456789012 SAVE? YES Save with RETURN, reject with “C” or a new reading. In the AUTO MEMORY MODE the ID will be saved automatically, 980 123456789012 SAVED The complete content of the data file regarding that transponder could be checked by using the SCROLL up/down buttons. 3.
BiTech Handheld Manual -DRAFT 980 123456789012 AC = weighing 980 123456789012 0 Add Value 3.6 Modus DISPLAY Shows an alphanumeric ALIAS that is connected with the transponder ID in the link list. XXXXXXXXXX Saved 4 The SETUP of the BiTech reader By pressing Key F the handheld changes to the MAIN MENU. The Options of the main menu are: ! SETUP OPERATION DATA SETUP contains all settings for the READER that are valid for both HOTKEYS.
BiTech Handheld Manual - DRAFT 4.2.1 LAST ID Shows the last 10 IDs. The IDs could be saved if they are not in the memory yet. Last ID X/10 S XXX XXXXXXXXXX Shows number X out of the last ten. With SCROLL keys move to the searched ID and select the ID with the ENTER key. The complete data of this ID will be displayed by using the SCROLL keys. S shows that the ID is saved already. If the ID is not saved yet, pressing ENTER again could save it.
BiTech Handheld Manual -DRAFT 4.3 The SETUP menu Comes with the submenus -> RF/ID BAUDRATE DISPLAY DISPLAY FORMAT TIME/DATE VOLUME POWER MANAGER SOFTWARE VERS. DEFAULT 4.3.1 RF/ID menu Consist of all functions for reading a transponder. READ LENGTH DOUBLE READ READ LENGHT Determines how many (xx) seconds the reader tries to read a transponder. Read Length = XX Seconds Choose by SCROLL keys and confirm by RETURN. DOUBLE READ defines if the same transponder will not be read into a certain time period.
BiTech Handheld Manual - DRAFT • LANGUAGE (English/Deutsch) -> ENGLISH DEUTSCH Choose by SCROLL keys and confirm by RETURN. • LIGHT OPTION -> ON AT EXT POWER OFF AT EXT POWER If LIGHT is switched ON/OFF when the reader is powered externally. • CONTRAST -> Contrast = X Choose from 1 to 5 with SCROLL keys and confirm by RETURN. • BRIGHTNESS as CONTRAST • POWER OFF -> POWER OFF XX SECONDS Choose XX from 3 to 20 by SCROLL keys and confirm by RETURN. 4.3.
BiTech Handheld Manual -DRAFT 4.3.5 TIME and DATE Offer different options to set time and date. -> SET TIME TIME FORMAT SET DATE DATE FORMAT SET TIME, change value by SCROLL, confirm by RETURN. TIME FORMAT, could be chosen between 12 or 24 h. SET DATE, change value by SCROLL, confirm by RETURN. DATE FORMAT, could be chosen between dd.mm.yy and mm.dd.yy. 4.3.6 VOLUME of Acoustic Signals Change value 0 to 15 by SCROLL confirm by RETURN. 4.3.7 POWER MANAGER For the selection of the battery type.
BiTech Handheld Manual - DRAFT 4.4.1 MEMORY SPACE Displays the current use of the memory, with the SCROLL keys also the amount of data in the link and ACTION CODES list could be displayed. 4.4.2 SHOW DATA Display the data in the memory. Move with the SCROLL keys through the data. When you choose a particular data with RETURN it switches into DATA VIEW MODUS. SHOW DATA ZX 980 123456789012 The complete data can be displayed by scrolling with the SCROLL keys through the lines.
BiTech Handheld Manual -DRAFT - 5 The DEFAULT setting The BiTech readers come with the following default setting: • ISO MODE STD • Both HOTKEYS with the same function o READ = YES o Confirm SAVE = YES o AC mode = OFF (Value 0) o DISPLAY FORMAT = BiTech Format o Show DISPLAY = 5 seconds • RF/ID - READ LENGTH = 7 seconds • TRANSPONDER = HDX, FDX-B, 4002 • DISPLAY = BiTech Format • COUNTRY CODE = Decimal • VOLUME = 5 • Language = English Changes in the setting will be saved automatically.
BiTech Handheld Manual - DRAFT 6 Technical Data Frequency 134,2 kHz Transponder types HDX compatible (ISO 11784/5) FDX-B compatible (ISO 11784/5) H4002 compatible (optional) Reading range: Approx. 15 cm with HDX transponder 30 mm Approx. 10 cm with FDX-B transponder 30 mm Interfaces Cradle Power supply 2 x 1,5V AA mignon batteries External power supply via cradle Recharge via cradle Protection IP 54 Temperature range 0 to 60°C Measurements and weight LxWxH 175x90x36 mm, approx.
BiTech Handheld Manual -DRAFT Regulatory notices Regulatory notices for Europe: Hereby, deister electronic GmbH declares that this equipment - if used according to the instructions - is in compliance with the essential requirements and other relevant provisions of the RTTE Directive 1999/5/ EC.
BiTech Handheld Manual - DRAFT - V07/06/05 deister electronic GmbH 30890 Barsinghausen Germany 19
deister worldwide Germany: deister electronic GmbH Hermann-Bahlsen-Str. 11 30890 Barsinghausen Tel.: +49 (0) 51 05 - 51 61 11 Fax: +49 (0) 51 05 - 51 62 17 info@deister-gmbh.de www.deister.com Great Britain: deister electronic (UK) Ltd. Camelgate, Spalding Lincolnshire PE12 6ET Tel.:+44 (0) 1775 - 717100 Fax:+44 (0) 1775 - 717101 info@deister.co.uk Belgium & Luxemburg: deister electronic office Business Park E 19 Battelsesteenweg 455/A 2800 Mechelen Tel.