compact Wiring & Installation Instructions V04/09/07
amanTag compact © Copyright 2007 by deister electronic GmbH All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of deister electronic GmbH. deister electronic GmbH reserves the right to make changes to any and all parts of this documentation without obligation to notify any person or entity of such changes.
amanTag compact Content 1. General Information...................................................4 2. Technical Data.............................................................5 3. Operation....................................................................5 4. Wiring & Configuration ..............................................6 4.1 Optical display ..................................................................................................6 4.2 Pin assignment......................................
amanTag compact 1. General Information ● An amanTag compact-Reader generates an undirected field in an area up to 3 meters. In a vertical line to the reader the reading range is up to 8 meters. ● An amanTag compact-Reader is able to recognize several transponders being in the reader-field at the same time. ● The reading range can be varied gradually. ● For exchange of data a Wiegand or RS 485 Interface can be used.
amanTag compact 2. Technical Data Meets EN(I-ETS) 300220 Dimensions (mm): 296 x 296 x 28 Transmission frequency: 8,1 kHz Receiving frequency: 433 MHz ISM-band Modulation: PSK Baud-rate in reading: 1500 Baud Sensibility: -100dBm Reading distance: up to 8 m, depending on the type of transponder Field strength in 8m distance: 99 dBμV/m average , 102 dBμV/m peak Interface: Wiegand, RS485 Voltage supply: 24V (18V...30V) 3.
amanTag compact 4. Wiring & Configuration 4.1 Optical display An amanTag compact is equipped with three LEDs for optical display. The functions assigned are as follows: LED yellow: “Power ON”-display. Turned on constantly when connected to the power supply. LED green: Tag received. Blinks in case a transponder telegram has been received. LED red: Tag in field. Is active as long as a transponder is located in the field.
amanTag compact 4.2 Pin assignment A schematic description of the position of the pins and dip-switches is given in the diagram below: yellow green red ST1 ST2 ST3 ST4 ST5 Bank A Bank B DIP-Switches In the lower part of the card there are five connector rails for connecting to the power supply and to other devices in the peripheral equipment. The connector rails are assigned as follows.
amanTag compact ST1 (PRX) P1 beeper–input P2 ground P3 positive currant voltage 24V (18V – 30V) P4 Wiegand-output D1 ( loading arrangement RS 232 ) P5 Wiegand-output D0 P6 Wiegand-output CP P7 LED green input P8 LED red input P9 RS485 - A P10 RS485 - B P11 Tamper-contact P12 Tamper-contact ST2 (SATELLITE) P1 positive currant voltage, 24V (18V ... 30V) P2 ground P3 RS485 - A P4 RS485 – B ST3 (SYNC) P1 positive currant voltage, 24V (18V ...
amanTag compact 4.3 DIP-switches The amanTag compact can be configured with two eight pole dip-switches (rail A and B). ON ON # # # # # # # # A1 A2 A3 A4 A5 A6 A7 A8 # # B1 # B2 B3 # # # # # B4 B5 B6 B7 B8 A1 activate the monitor tag function. A2 always has to be „on“.
amanTag compact Examples for adjusting the door-number: Door-number 1: ON # # A1 A2 # # A3 # # A4 A5 # # A6 A7 A8 Door-number 2: ON # # A1 A2 # # A3 # # # A4 A5 A6 # A7 A8 Door-number 3: ON # # A1 A2 # # A3 # # A4 A5 # # A6 A7 A8 Door-number 8: (reserved, should not be used) ON # # A1 10 # # A2 A3 # # A4 A5 A6 # # A7 A8 deister electronic GmbH 30890 Barsinghausen Germany V04/09/07
amanTag compact Examples for adjusting the wake-up-range: Range 1: ON # # # # # # # # B1 B2 B3 B4 B5 B6 B7 B8 Range 2: ON # # # B1 B2 B3 # B4 # # # B5 # B6 # # B7 B8 Range 3: ON # # B1 B2 B3 B4 # # B5 B6 # B7 # B8 # B5 # # B7 B8 Range 8: ON # B1 # B2 V04/09/07 # # B3 B4 # B6 deister electronic GmbH 30890 Barsinghausen Germany 11
amanTag compact 5. Installation 5.1 General Information ● During the installation it is important to take care that the readers are not too close together. The low frequent fields of the readers must not overlap. ● The wake-up-fields of the different readers must not overlap. The range of the field can be varied by the dip-switches B1-B4. ● Mounting on a metallic surface or on brick-walls with lots of steel reinforcement can reduce (or unexpectedly extend) the wake-up-range of the reader. 5.
amanTag compact V04/09/07 deister electronic GmbH 30890 Barsinghausen Germany 13
amanTag compact 6. Regulatory notices Hereby, deister electronic GmbH declares that this equipment - if used according to the instructions - is in compliance with the essential requirements and other relevant provisions of the RTTE Directive 1999/5/ EC. A full declaration of conformity can be requested at: info@deister-gmbh.de Approved for use in all European countries.
amanTag compact Notes: V04/09/07 deister electronic GmbH 30890 Barsinghausen Germany 15
deister worldwide Germany: deister electronic GmbH Hermann-Bahlsen Str. 11 30890 Barsinghausen Tel.: +49 (0) 51 05 - 51 61 11 Fax: +49 (0) 51 05 - 51 62 17 info@deister-gmbh.de www.deister.com France: deister electronic france 101 rue Pierre Semard 92320 Chatillon Tel.: +33 (0) 1 47 - 35 78 78 Fax: +33 (0) 1 47 - 35 92 59 info.fr@deister.com Great Britain: deister electronic (UK) Ltd. Stapleton Way, Enterprise Park Spalding, Lincolnshire PE11 3YQ Tel.: +44 (0) 1775 - 717100 Fax: +44 (0) 1775 - 717101 info.
