DÉMARREUR À DISTANCE ® MANUEL DE L’USAGER MODÈLE RSS-2524 Conçu pour tout véhicule automobile hybride à essence ou diesel. Peut être doté d’un système de sécurité en option. (ENGLISH ON REVERSE) VEUILLEZ CONSULTER LES RÈGLES DE SÉCURITÉ AVANT L’UTILISATION DE CE PRODUIT. CERTAINES FONCTIONS PEUVENT NÉCESSITER DU MATÉRIEL SUPPLÉMENTAIRE NON INCLUS. NOS DE BREVETS CAN 1.130.426 É.-U. 4.345.554 - 5.614.883 - 5.617.819 - 5.673.
RÉGLEMENTATION Ce dispositif satisfait aux exigences d’Industrie Canada (IC) - Gestion des radiofréquences, prescrites dans le document CNR-210. Son utilisation est autorisée seulement sur une base de non-brouillage et de non-protection; en d’autres termes, ce dispositif ne doit pas être utilisé s’il est établi qu’il représente une source de brouillage nuisible pour les services autorisés par IC.
MERCI D'AVOIR CHOISI UN DÉMARREUR À DISTANCE ASTROSTART! Comme vous, la compagnie Astroflex Electronics est soucieuse de l’environnement. C’est pourquoi nous vous suggérons d’utiliser le temps de fonctionnement de deux minutes lors du démarrage à distance de votre véhicule pour réchauffer les fluides du moteur. Votre télécommande vous permet de régler vous-même le temps de fonctionnement.
RÈGLES DE SÉCURITÉ Lisez bien toutes les règles de sécurité suivantes avant d’utiliser ce produit. RÈGLES GÉNÉRALES Ne jamais effectuer un démarrage à distance lorsqu'une personne ou un animal occupe le véhicule. Ne laissez jamais une personne ou un animal sans surveillance à bord du véhicule lorsque ce dernier est maintenu en marche par le démarreur à distance (mode continu). Rapportez immédiatement tout problème de fonctionnement au dépositaire AstroStart qui a procédé à l’installation.
SÉQUENCE DE SÉCURITÉ POUR VÉHICULES À BOÎTE DE VITESSES MANUELLE Votre démarreur à distance a été conçu de manière à vous contraindre à effectuer une série d'actions qui ont pour but d'assurer que le levier de vitesses soit placé au point mort (neutre) au moment où vous quittez votre véhicule. Cette série d'actions, appelée «séquence de sécurité», vise à prévenir tout démarrage à distance dans des circonstances où il ne serait pas sécuritaire que le moteur du véhicule soit mis en marche.
LA TÉLÉCOMMANDE Votre télécommande peut émettre sur deux canaux différents, vous permettant ainsi de commander à distance deux véhicules séparément. Jusqu’à quatre télécommandes peuvent être attribuées à votre véhicule. NOTE : La portée de votre télécommande peut être réduite si une pile est faible; elle peut aussi être affectée par la présence de structures métalliques ou de poteaux électriques à proximité, ou encore par une trop forte concentration de véhicules dans un terrain de stationnement bondé.
TABLEAU DES COMMANDES BOUTONS COMMANDES PANIQUE CONFIRMATION GROUPE 1 GROUPE 2 OU (> 4 SEC.) ET (> 4 SEC.) DÉMARRAGE / MODE CONTINU ARRÊT (> 4 SEC.) KLAXON FEUX SIRÈNE* 30 / 60 SEC. 1 1 1 1 1/3/X 2/4/X ¡ VERROUILLAGE / ARMEMENT* (LA PORTÉE EST RÉDUITE SI <2 SEC.) 1 1/3 DÉVERROUILLAGE / DÉSARMEMENT* (LA PORTÉE EST RÉDUITE SI < 2 SEC.) - 2/4¡ - 1/3 3 - - - COFFRE 1 (>4 sec.
CONFIRMATION COMMANDE DEL DÉMARRAGE PRÊT CONFIRMATIONS INSTANTANNÉES TONALITÉ AIGUE DÉMARRAGE NON-PRÊT ROUGE BASSE DÉMARRAGE RÉUSSI MÉLODIE ASCENDANTE ARRÊT MÉLODIE DESCENDANTE AIGUE, BASSE VERROUILLAGE ARMEMENT 3X (AIGUE, BASSE) VALET EN FONCTION OU ZONE NON-PROTÉGÉE BASSE, AIGUE DÉVERROUILLAGE DÉSARMEMENT 3X ( BASSE, AIGUE) AVEC CONDITION D’ALARME COMBINAISON DE UN DES ÉTATS DE DÉMARRAGE ET DE UN DES ÉTATS DES PORTIÈRES, VOIR LES CASES EN GRIS PLUS HAUT.
DURÉE DE FONCTIONNEMENT DU MOTEUR Le moteur de votre véhicule s'arrêtera automatiquement au terme d'une durée de fonctionnement prédéterminé (voir «Réglage de la durée de fonctionnement» à la page 8). Les feux de position demeureront allumés tant que le moteur sera en marche. ENTRÉE D'IMPULSION Votre démarreur à distance est muni d’une entrée d'impulsion négative.
INTERRUPTEUR PRINCIPAL L'interrupteur principal est habituellement monté sous le tableau de bord. Il comprend un bouton à deux positions (ON et OFF). L'interrupteur permet d'annuler les fonctions de démarrage. Il n'interrompt cependant pas les autres commandes qui demeurent actives (alarme, commande des verrous, etc.). ARRÊT Consultez le tableau des commandes à la page 5 pour connaître la ou les touches à appuyer.
SYSTÈME DE SÉCURITÉ (OPTIONNEL) La présente section s’applique à un système de sécurité AstroStart (rajouté en option), qui ne doit pas être confondu avec le système d’origine du véhicule. ZONES DE PROTECTION Votre système de sécurité peut mettre à profit jusqu’à six dispositifs de supervision différents à la fois pour protéger votre véhicule. Ces dispositifs sont raccordés au système sur différentes entrées appelées zones de protection.
FONCTIONNEMENT Votre système d’alarme peut fonctionner selon trois modes différents, c'est-à-dire actif, réarmement semi-passif et réarmement passif selon la programmation initiale. Consultez le paragraphe qui correspond au mode auquel votre système à été configuré lors de l’installation. ACTIF En mode actif, l'alarme doit être armée et désarmée à l'aide de la télécommande. Voir le tableau des commandes à la page 5.
Le tableau ci-dessous indique l’effet de chaque zone sur le cycle de réarmement. Zone de protection Effet sur le cycle de réarmement Capot Portières Ces quatre zones prolongent le délai de réarmement tant et aussi longtemps qu'elles Capteur additionnel (coffre) sont maintenues en état d’infraction.
Le tableau suivant donne la signification des codes de zone (nombre de clignotements). CODES DE ZONE Clignotement 1 2 3 4 5 Zone visée Le système est armé. Une portière est/a été ouverte. Le capot est/a été ouvert. Un état d’alarme est/a été détecté sur l’entrée du capteur de choc. La clé de contact est/a été à la position «RUN». Un état d’alarme est/a été détecté sur l’entrée du capteur additionnel.
GLOSSAIRE SIRÈNE La sirène émet six sons différents, c’est-à-dire qu’elle retentit de façon répétitive et par alternance selon six mélodies différentes (fourni seulement avec le kit d’alarme optionnel). Elle retentit de façon intermittente (petit coups répétitifs) lors d’une pré-alarme, et de façon continue lors d’un état d’alarme. Elle peut donner une confirmation des commandes ARMEMENT et DÉSARMEMENT à l’aide de petits coups (ou piaulements); voir le tableau dans la section CONFIRMATION.
DÉVERROUILLAGE / DÉSARMEMENT Appuyer sur le bouton pendant 2 secondes. Le déverrouillage des portières s'effectue en même temps que l'alarme est neutralisée. Les feux de position clignotent deux fois et la sirène retentit deux coups pour confirmer la réception de la commande et vous indiquer qu'aucun état d'alarme ne s'est produit en votre absence. Si une infraction s'est produite, la confirmation est différente (4 coups) pour vous en avertir.
AUTRES COMMANDES ANTIVOL (COUPE-CIRCUIT) Programmable Actif ou Inactif lors de l’installation. Votre démarreur à distance est muni d’un système antivol. Cette fonction, lorsque activée, coupera tout circuit nécessaire au fonctionnement du véhicule (raccordement optionnel). Deux types d’antivols sont offerts.
LOCALISATEUR Appuyer sur les boutons et simultanément pendant 2 secondes. Cette fonction vous permet de faire entendre le klaxon (courte mélodie) et d'allumer les feux de position pour vous permettre de localiser votre voiture dans un grand stationnement. MISE EN SOURDINE DE LA TÉLÉCOMMANDE La télécommande peut cesser d’émettre des sons si vous le désirez. Consultez le tableau des commandes à la page 5 pour connaître la ou les touches à appuyer.
CODES D'ÉTAT D'ALARME Cette commande permet d'identifier quelle zone est en état d'infraction lors de l'armement ou celle qui a généré l'état d'alarme. Consultez le tableau des commandes à la page 5 pour connaître la ou les touches à appuyer. Les feux de position clignoteront un nombre de fois correspondant au code de la zone de protection en état d'infraction. Si plus d'une zone est en infraction, le code de la zone ayant le plus haut niveau de priorité est affiché.
VÉRIFICATIONS RELATIVES AUX VÉHICULES À TRANSMISSION AUTOMATIQUE Si, pour parvenir à déplacer le levier de vitesses de la position «P», la clé doit se trouver dans le contact, votre véhicule est sécuritaire tant que les clés sont hors de la portée des enfants. Par contre, si le levier peut être embrayé sans que la clé ne soit dans le contact, effectuez la vérification suivante. • Assurez-vous que le frein de stationnement est appliqué. • Placez le levier de vitesses en position «D».
® REMOTE CONTROL ENGINE STARTER USER MANUAL MODEL RSS-2524 For all hybrid, gasand diesel-powered vehicles. This model may be equipped with an optional security system. (FRANÇAIS AU VERSO) CONSULT SAFETY PRECAUTION SECTION BEFORE USING THIS PRODUCT. SOME FEATURES MAY REQUIRE ADDITIONAL MATERIAL (NOT INCLUDED). PATENT NOS CAN 1.130.426 USA 4.345.554 - 5.614.883 - 5.617.819 - 5.673.
GOVERNMENT REGULATIONS This device complies with the Industry Canada Radio Standards Specification RSS 210. Its use is authorized only on a no-interference, no-protection basis; in other words, this device must not be used if it is determined that it causes harmful interference to services authorized by IC. In addition, the user of this device must accept any radio interference that may be received, even if this interference could affect the operation of the device.
THANK YOU FOR CHOOSING AN ASTROSTART REMOTE CAR STARTER! Just like you are, Astroflex Electronics is concerned with the environment. This is why we are suggesting you to use the two-minute runtime when you remote-start your vehicle to warm up engine fluids. You can set the runtime yourself using your transmitter. We take this opportunity to remind you to properly defrost your windows and remove all the snow on your vehicle before driving on public roads.
SAFETY PRECAUTIONS Before using this product, carefully read the following safety precautions. GENERAL RULES • Never perform a remote start when a person or animal is inside the vehicle. • Do not allow any person or animal to remain inside the vehicle when the engine is running under remote starter control (continuous mode). • Immediately report any malfunction to the AstroStart dealer that performed the installation. • Under no circumstance can this product or its use be modified.
SAFETY SEQUENCE FOR MANUAL TRANSMISSION VEHICLES Your remote starter was designed to force you to perform a series of actions that will ensure that the gearshift lever is in neutral position when you exit the vehicle. This series of actions is called a "safety sequence" and is aimed at preventing any remote start in situations where remote starting the engine would not be safe.
THE REMOTE CONTROL Your remote control can transmit on two different channels, allowing control of two separate vehicles. Up to four remote controls can be assigned to your vehicle. NOTE: The range of your remote control can be affected by a weak battery, interference from nearby metal structures, hydro poles, or crowded parking lots. Only the "Panic" command is transmitted on both channels when a single command is sent (alternating transmission channels).
TABLE OF COMMANDS CONFIRMATIONS BUTTONS COMMAND GROUPE 1 PANIC GROUPE 2 OR AND (> 4 SEC.) (> 4 SEC.) START / CONTINUOUS MODE STOP (> 4 SEC.) HORN PARKING LIGHTS SIREN* 30 / 60 SEC. 1 1 1 1 1/3/X 2/4/X ¡ LOCK / ARMING* (REDUCED RANGE IF < 2 SEC.) 1 1/3 UNLOCK / DISARMING* (REDUCED RANGE IF < 2 SEC.
CONFIRMATION LED SYSTEM IS NOT READY FOR STARTING INSTANTANEOUS CONFIRMATIONS Parking light confirmations are mandatory. Horn confirmations are optional (programmable) and require an additional connection and/or equipment during installation. Confirmations are explained in more detail under each command.
ENGINE RUNTIME Your engine will stop automatically after a preset time (See "Setting the runtime" on page 8). Parking lights will stay on as long as engine is running. TRIGGER INPUT Your remote starter is equipped with a negative trigger (pulse) input. This input can be connected to another remote control device or to an AstroStart RST-2 timer output (optional), part number 310-903-502.
MAIN SWITCH Main switch is usually mounted under dashboard. It is a toggle ON/OFF switch that is used to cancel start functions. It does not disable other commands which remain active (alarm, lock/unlock commands, etc.). STOP Refer to the table of command on page 5 to know which button to press. This command only applies when engine is kept running by Remote Starter. It is used to stop the run time, the panic mode as well as the alarm condition without disarming the security system.
SECURITY SYSTEM (OPTIONAL) The current section only applies to an AstroStart security system (added as an option) which must not be confused with the vehicle’s OEM system. PROTECTION ZONES Your security system can use up to six different monitoring devices simultaneously to protect your vehicle. These devices are connected to the system on different inputs called protection zones. One of these zones can send an audible warning (7 chirps), while the other five generate an alarm condition if system is armed.
OPERATION Your alarm system has three different operating modes, active, semi-passive rearming and passive rearming depending on initial programming. See the relevant paragraph for the mode your system was configured in during installation. ACTIVE In active mode, the alarm must be armed and disarmed using the remote. See Table of Commands on page 5. Alarm is armed as soon as command is received, even if a zone is in violation when command is received.
The following table shows the effect that each zone has on the rearming cycle. Protection zone Hood Doors Additional sensor (trunk) Shock sensor Effect on rearming cycle These four zones prolong rearming cycle as long as they remain in violation. Activated by ignition key: Cancels rearming Activated by remote starter: No effect Warning No effect Applying brakes or ignition key in RUN position cancels rearming (until a door is opened, which causes rearming cycle to restart from the beginning).
The following table shows the meaning of zone codes (number of flashes). ZONE CODES FLASHES 1 2 3 4 5 ZONE INDICATED System is armed. A door is/was open. Hood is/was open. Alarm condition is/was detected on shock sensor input. Key is/was in the run position. Alarm condition is/was detected on additional sensor input. 6 Additional sensor monitors status of ____________________________________________________ 7 Loss of power (+12V battery supply was removed).
GLOSSARY SIREN Siren has six different sounds, i.e., it chirps repeatedly and has six different melodies (supplied only with optional alarm kit). It chirps intermittently (short repeated chirps) during a pre-alarm and continuously during an alarm condition. It can confirm arm and disarm commands with short chirps; see table in CONFIRMATION section. This function is programmable as active or inactive during installation. HORN Horn beeps intermittently (short repeated beeps) during an alarm condition.
UNLOCK / DISARM Press the button for 2 seconds. Doors are unlocked and alarm is disarmed, parking lights flash and siren chirps twice to confirm command has been received and that no alarm condition was generated during your absence. If there was a violation, confirmation is different (4 flashes or chirps) to warn you. See table of alarm codes to know which zone generated alarm condition.
OTHER COMMANDS ANTITHEFT (CIRCUIT DISABLER) Programmable as Active or Inactive during installation. Your Remote Starter is equipped with an antitheft system. This system consists of an output that controls a relay that cuts all circuits required to operate your vehicle (optional connection). “PASSIVE ARMING» TYPE ANTITHEFT This type of antitheft system arms automatically when ignition key is turned from RUN to OFF and remains OFF for one minute.
CAR FINDER and buttons for 2 seconds. Press the This function sounds horn (short tune) and flashes parking lights to help you locate your vehicle in a large parking lot. REMOTE SILENT MODE The remote can be programmed to be used in silent mode. Refer to the table of command on page 5 to know which button to press. The audible confirmations from the remote control are Deactivated/Reactivated. KEYPAD LOCK The keypad of your remote can be locked to prevent any unwanted commands to be sent to your vehicle.
ALARM CONDITION CODES Use this command to identify which zone is in violation during arming or which generated alarm condition. Refer to the table of command on page 5 to know which button to press. Parking lights will flash number of times corresponding to code for protection zone in violation. If more than one zone is in violation, code for the zone with highest priority is shown (1 = highest priority). See table of codes below. Code 1 2 3 4 5 6 7 8 Protection Zone System is armed. A door is/was open.
GEARSHIFT CHECK APPLICABLE TO AUTOMATIC TRANSMISSION VEHICLES If key must be in ignition for gearshift to be moved out of P, your vehicle is safe as long as keys are kept away from children. If, on the other hand, gearshift can be put in gear without key being in ignition, proceed with this simple check. • Make sure that the parking brake is applied. • Put gearshift in gear (D). • Remain in the vehicle and be ready to apply brakes. • Start vehicle with remote starter.