Specification

３０寸摇头喷雾立扇（带脚轮）
1
Adjusting the fan tilt angle
□
□
□
2
Turning the fan On/Off and adjusting
ITEM NO.: FAN-P30WM
120V / 60Hz, 2.0A
30" HEAVY DUTY PEDESTAL MISTING FAN
1 2 3 4 5 6 7 8 9 10
PACKAGE CONTENTS
ASSEMBLY INSTRUCTIONASSEMBLY INSTRUCTION ASSEMBLY INSTRUCTION
ASSEMBLY INSTRUCTION
OSCILLATION INSTRUCTION
ASSEMBLY INSTRUCTION
Figure Quantity
Description
1
Front Guard
Misting Kit
1
1
2
Blades 1
3
Rear Guard
4 1
5 Motor 1
6 1
7
Extension Pipe
1
9
Lower Pole
8
Shock Absorbent Spring
1
Base 1
1
2
2
1
1
1
3
4
ASSEMBLY INSTRUCTION
2. Through the bottom of base by M5*12 Screws and φ5 Star Washers,
and fasten the Wheels with M5 Nuts.
3. Remove five Screws from base. Save them for step 4.
4. Attach Lower Pole to Base by tightening back the five Screws from
Step 3.
1.Put the Wheels on Base, fasten them by M5*12 Screws, φ5 Star
Washers and M5 Nuts.
1
2
3
4
5
6
7.Remove four sets of hexagonal nuts, spring washes, and bowl
washers from the motor. Save them for step 8.
5. Loosen and remove the two screws (1) on the height adjusting knob
on the upper connecting pole (2). Place the spring (3) into the
standing pole (4). Insert the upper connecting pole (2) into the
standing pole (4), making sure the holes on the height adjusting
knob and the standing pole (4) are aligned. Insert the two screws
(1) into the standing pole (4) and tighten them. Adjust the height of
the upper connecting pole (2) as desired and secure using the
adjusting knob.
6. Insert a bolt (5) into the hole on the neck bearing (found on the motor)
and into the top of the upper connecting pole. Secure them together
using a bushing (1) and a nut (2). Insert one bolt (6) through the hole
in the neck bearing and into the top of the upper connecting pole and
secure them a bushing (4) and a nut (3).
10. Attach the front guard (1) to the rear guard (2) and secure them
together using the clips on the front guard.
12. Connect the misting switch (1) to the water pipe (2) and tighten it.
Turn the switch (open) to open the misting function. Turn the switch
(close) to close the misting function.
Turn the oscillation function on by pushing the oscillation button down.
11. Secure the assembly on the front and rear guard by tightening the
screw (1) and star washer (2) on the bottom of them and nut (3).
8.Attach the rear guard (4) to the screws found on the motor and secure
them together using four bowl washers (1), four spring washers (2),
and four nuts (3) from step 7.
9. Attach the blade (2) to the shaft on the motor and secure them
together using two screws (1).
2
Motor shaft
Secure them together
1
1
1
1
3
2
1
2
1
2
3
4
5
6
7
8
9
The manufacturer warrants this product to be free from manufacturing defects
in the material and workmanship under normal use for a period of one year after
the date of purchase by the original purchaser.
This warranty does not cover transit damages. This warranty does not apply to
damages from accident, misuse, alteration of any kind to the fan or where the
connected voltage is more than above the nameplate voltage. This warranty
does not apply to the finish on any portion of the product. Servicing performed
by unauthorized persons shall render the warranty invalid. The warranty is not
responsible for damages of any kind, including accident and consequential
damages. Some states do not allow the exclusion or limitation of the incidental
or consequential damages, so the above exclusion or limitation may not apply
to you. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
DESCRIPTIONPART PART #
FAN-P30WM
Blade
1
1
2
4
3
2
1
4
Test GFCI (Ground Fault Circuit Interrupter) plug BEFORE EACH USE.
Plug GFCI into power outlet. Press RESET button. Indicator should turn red.
Press TEST button. Indicator should turn off. GFCI plug is tripped.
Press RESET button again for use. DO NOT USE FAN IF ABOVE TEST FAILS.
Call customer service for assistance.
TEST button
RESET button
indicator
Adjust the desired speed by pulling the
chain switch at the motor.
plug the fan into an electrical outlet.
Ensure the fan is unplugged from
the power source beforeadjusting
the height or angle.
Always turn off and unplug the fan after
using.
0 Stop 1 Low 2 Medium 3 High
□
□
GFCI PLUG Pull Chain Switch
Place the fan on a safe, flat surface
where it cannot fall or be pulled by
the cord.
To adjust the angle of the fan head
(A), loosen the M6 hex nut (2), tilt
the fan head (A) to the desired angle,
and re-tighten the M6 hex nut (2).
Loose
Tight
3/4" Water Pipe Terminal 3/4"-11.5 External Thread
3/4"-11.5 Internal Thread
Open
Close
①
②
2
M6 hex nut
A
READ & SAVE THESE INSTRUCTIONS
Questions, problems, missing parts? Before returning the product,
please e-mail our customer service by
[e-mail]
READ AND SAVE THESE INSTRUCTIONS
1. To prevent serious injury or property damage,read and understand
owner's manual before operating.
2. This prodct can be used indoor or outdoor with a proper GFCI plug.
1
Screw
Star Washer
Nut
Screw
Star Washer
Nut
1. Read and save these instructions. Do not operate fan unless you have
read these instructions.
2. Unplug the fan before moving it or performing maintenance. Do not touch
the fan when your hands are wet.
3. Those who are not qualified electricians should not disassemble, repair or
rebuild the fan.
4. Unplug the fan when it is not in use.
5. DO NOT unplug the fan by pulling the cable cord. Unplug by holding the
plug and pulling.
6. DO NOT use the fan when there is damage to the cable cord or plug. If
the supply cord is damaged, it has to be replaced by the manufacturer,
its service agent or similarly qualified persons.
7. To Reduce The Risk Of Fire, Electric Shock Or Injury To Persons, Do Not
Use Replacement Parts That Have Not Been Recommended By The
Manufacturer (e.g. Parts Made At Home Using A 3D Printer).
8. DO NOT use the fan close to fires.
9. DO NOT insert your hand or other objects into the grille or the movable parts.
10. To reduce the risk of fire or electric shock, do not use this fan with any
solid-state speed control device.
11. Do Not Use An Extension Cord With This Fan.
1. Unplug the fan from the socket and clean it with a soft cloth.
2. DO NOT immerse the fan.
3. Fit the guard onto fan before starting up the fan.
4. This fan is not intended for use by people (including children) with
reduced physical, sensory or mental capabilities or lack of experience
and knowledge unless they have been given supervision or instruction
concerning use of the fan by a person responsible for their safety.
Supervise children to ensure they do not play with the fan.