Controls and instruments Digital Indicators—Tachometer, Ground Speed, Transmission, and Set Speed A—Tachometer: Displays engine speed in multiples displayed, no speed signal is being received. B—Travel Speed Indicator: Displays travel speed in either miles per hour or kilometers per hour, depending on operator selected units (U.S. or Metric) displayed, no speed signal is being received. C—Transmission Information: Shows if transmission is in Neutral—N.
Controls and instruments Gauges—Coolant Temperature, Diesel Exhaust Fluid (DEF) Level, and Fuel Level A—Coolant Temperature Gauge: Shows engine coolant temperature between 40—120 °C (104—248 °F}. All segments are off when coolant temperature is below 40 °C {104 °F}. All segments are lit when temperature is 120 °C {248 °F) and above. B—Fuel Level Gauge: Displays fuel level in tank. Each lighted segment represents 4% of fuel tank total capacity. When fuel tank is full, all segments are lit.
Controls and instruments CommandARM™ Joystick Controls Setup Icon appears around controls that may be setup to control other functions. Review Controls Setup Page (see “Controls Setup” in CommandCenter™ of this operator's manual) to verify function of each control NOTE: Joystick affords operator to assign device with various tractor or implement functions. This process is chaffed “Assignment” input fo function. See “Controls Setup” in GomimandGenter™ section of this Operator's Manual for more information.
Controls and instruments | CommandARM™ SCV Controls NOTE: Re configurable SCV Controls allows operator to match device with various implement functions. This process is called “Assignment” input fo function. See “Controls Setup” in CommandCenter™ section of this Operator's Manual for more information. SCV Lock button jocks out control inputs to SCV Levers and Front Hitch Lever only.
Controls and instruments CommandARM™ Left Side Controls i— Diff Lock Button J— Auto Diff Lock Button K--Auto FWD Button L—Hand Throttle Control M--ECO ON/OFF Button N--Fiat Pedal Lock/Unlock A—Speed Contort Lever/Shift Lever B--SCI Control Lever Lock C—AutoTrac™ Resume Button D--iTEC™ 1 Button E-iTEC™ 2 Button F—iTEC™ 3 Button Button GwiTEC™ 4 Button OwFieldCruise™ ON/OFF H—MFWD Button Button Command Arm is a trademark of Deere & Company Autocrat is a trademark of Deere & Company CITE is a trademark of Deer
Controls and instruments Accelerator Pedal (if Equipped) Foot operated throttle controls engine or ground speed dependent on transmission mode, Depress accelerator (A) to increase engine rpm or wheel speed A--Accelerator Pedal RO47225,8000157 219. 30ILIL 12.97% External Switches AGAIN: To prevent injury or damage caused by tractor movement, be sure transmission is in PARK position before using external raise/lower switches. Stay clear of interference points when using external raise/lower switches.
Controls and instruments Front hitch and front PTO equipped tractors may lase be equipped with front mounted external switches, Tractors equipped with front hitch may have external raise (F) and lower switches (G).
CommandCenter™ | Onscreen Help Generation 4 CommandCenter™ displays are equipped with detailed help information in the software. Onscreen help is available in Help Center (found in display menu) or by pressing Information (i) buttons at the top of most pages. information buttons link directly to help information for that page.
CommandCenter™ Generation 4 Command Center Processor Generation 4 Command Center software runs on a processor separate from the display. There are two processor options available. NOTE: Maximum capabilities for each processor are listed. Depending on machine configuration, some functions may not be available.
CommandCenter™ Run Page Structure oo Ra Main Menu (A) lists all applications installed on display and machine. Shortcut soft keys (B) provide quick access to frequently used applications and functions. On 7 in. display, select expand button to display shortcut soft keys. Run Page Navigation buttons (C) cycle through multiple run pages. See Layout Manager for more information. Select the area indicated (D} to display Status Center.
CommandCenter™ Diagnostics Center = Diagnostics Center is the one place fo find diagnostics for the entire system, « It can be found on System tab of the display menu. 037272 N17 115 Diagnostics Center HO§4949.0 Display and Sound « Along with display brightness and volume, Display and Sound can be used to calibrate display and configure multiple displays « It can be found on System tab of the display menu.
CommandCenter™ EN--08) 5.15 Controls Setup = Configures an ISOBARS or tractor joystick to control tractor or implement functions. « It can be found on Applications tab of the display menu Controls Setup HC§4949 3 Fields I=L 13 « Field names are used to organize information se it is easier to find and use data, such as guidance lines, = Use Fields application to setup Clients, Farms.
CommandCenter™ Layout Manager {re rails * Use Layout Manager to create and modify run pages so important information and functions can be accessed from the main page. « It can be found on Applications tab of the display menu.
CommandCenter™ Automation Status Overview a * Use Automation Status application to see which tractor AUTO functions are being controlled and their current status, « [t can be found on Application tab of display menu ona Tractor Settings Overview Fa Tractor Settings tab allows selection of application main pages. Available applications vary depending upon tractor configuration. Audio RAG « Use Audio application to adjust audio settings.
CommandCenter™ iTEC™ RXA * Use ITEC™ application to program and repeat common a tasks. a « For more information see iTEC™ section of this = Operator's Manual. iTEC™ CITE is a trademark of Deere & Company KT81203 Lights No raucous * Use Lights application to adjust lights settings.
CommandCenter™ Rear Hitch Rx so + Use Rear Hitch application to adjust rear hitch settings. + For more information see Hitch section of this & Operator's Manual. Rear Hitch KT8120 sev « Use SCV application to adjust SCV setting. « For more information see Hydraulics and Selective Control Valve section of this Operator's Manual SCV KT E120 ~1905SEP1 2 Suspension RANIB4076 -TAURUS 13 * Use Suspension application fo adjust suspension settings.
CommandCenter™ Navigate Generation 4 CommandCenter™ NOTE: Images are reference and may differ by tractor configuration or operator settings. As operator pages through CommandCenter™. more in depth information is presented. allowing operator to fine tune tractor functions. Navigating CommandCenter™ Pages & & Use Touch Screen CommandCenter™ buttons or icons to make selection. For input boxes use either key pad, or select input box and scroll adjustment dial (C) to desired value.
CommandCenter™ Activating System Cold startup occurs when display has not operated in last 24 hours or has lost switched power. Cold startup‘fakes finger than warm startup for display to power up (approximately 30 seconds), Speed with which display system activates will vary, depending upon how recently tractor has been used.
CommandCenter™ Navigate to Display & Sound 1. Select Menu. 2. Select System tab. 3. Select Display & Sound icon. A—Brightness Tab Mode B--Sound Tab Toggle Bar Multiple Displays Tab E—Day Settings F—Night Setting Fou HERE HG aura 13 Display & Sound Main Page KTA1203.0003031 -19-306U% 13-31 Display & Sound Display & Sound application adjusts display brightness and volume level. If multiple displays are connected, use this application to configure which functions appear on each display.
CommandCenter™ | EN 208A 13 Brightness Settings Select either settings bunion to display a popup page for corresponding brightness mode. Depending on mode selected with settings button, adjust display and cab brightness by using plus and minus buttons. A—Day Settings C—Display Brightness B—Night Settings D-Cab Brightness 22 Sound UN--20818Y15 Change display volume by selecting increase or decrease buttons.
CommandCenter™ Navigate to Date & Time 1. Select Menu. 2. Select System tab. 3. Select Date & Time Icon.
CommandCenter™ | Change Current Date Date can only be changed if GPS is not connected or GPS signal is not available. Otherwise, GPS signal determines date. Date Format does not depend on GPS signal, and can be changed at any time. 1. Select day, month, or year. 2. Use keypad to enter correct value. Select Done to apply changes or Cancel fo return fo previous page without applying changes. Date Format 1. Select Date Format box. 4 Aw Date Set by User B--Date Determined by GPS 2.
CommandCenter™ Navigate to Language & Units 1. Select Menu. 2. Select System tab. 3. Select Display & Sound icon.
CommandCenter™ Changing Pages and Values Various methods are provided to allow selection and modification of CommandCenter™ pages and values. « A—Section Tab: To change to different section topic, click desired section tab. + Select to open application + C—Bar Graph: To change value, use increase or decrease buttons. » D—Slider Graph: To change value, select slider graph module and use increase or decrease buttons. « E—Input Box: Use increase or decrease buttons to adjust value. To enter new values or text.
CommandCenter™ Generation 4 CommandCenter™ Status Center Status Center is found in top region on 10 inch display or ~~ F*1% bottom left region on 7 inch display. Status Center functions: on E27 rn so 10idnck Display Top Region Status Center icon zr + A—Date & Time: Adjust date and time +» B—Data Storage: View data usage.
CommandCenter™ Navigate to Multiple Displays CAUTION: Implement Detected Improper operation can cause unintended implement movement. To avoid death or serious injury to a bystander, understand how this display operates the functions of the implement. Read and understand the Implement Operator's Manual. Message occurs when system detects an ISOBARS implement. For more information, read Operator Manuals for [SOBS Implements. in some cases it may be necessary fu operate with more than one ISO terminal display.
CommandCenter™ Multiple Displays Generation 4 Command Center may be configured to run with the following John Deere displays connected at comer post. « Original Green Star Display (without Mobile Processor) * G82 1800 * G82 2600 * G83 2630 Some applications, such as Autocrat, cannot run on both displays at the same time. Activation do not transfer between displays automatically. They may only be moved using the transfer process on StellarSupport.com Installing a GS2 or G83 Display 1.
CommandCenter™ Software Manager Use Software Manager to update software, activate features, and find software version details. Navigate to Software Manager 1. Select Menu. 2. Select System tab. 3. Select Software Manager application PUBS 13 Software Manager 19-0845 13 112 Software Packages Generation 4 display software and help files are organized into packages. Each package is listed individually on Installations and Updates tab and Version information tab.
CommandCenter™ Install Software Updates 1. Insert USB drive in to USB port in machine or on display. 2. When "USB Drive Options" page is displayed, select Install Software. This displays Installations & Updates tab of Software Manager. . Only software packages that are newer than what is currently installed are displayed. All packages are selected by default. Select Install button. If an update does not start, follow the onscreen messages to resolve conflicts.
CommandCenter™ Remote Software Updates (If Equipped) Service ADVISOR™ Remote (SAR) provides John Deere™ dealer technician or company person ability to update vehicle software remotely using John Deere™ mathematics infrastructure. Service ADVISOR ™ Remote User Interface on CommandCenter™ informs vehicle operator when new software is available for download or installation. Interface allows operator to accept or cancel software download.
CommandCenter™ Import Data import data from USB drive. Use this option in the following examples: « Import field names and guidance lines from anther 2630 display or compatible desktop software. NOTE: Choose G83 2630 card format when exporting from Apex. To use lines from other Green star displays, unload fines in to Apex and then export in GS3 2630 card format.
CommandCenter™ Navigate to Diagnostics Center Rots SHARES 10.12 on 1. Select Menu. Si 2. Select System tab. System Tah — Diagnostics Center lean 3. Select Diagnostics Center icon. May — 3 oD A—Application Diagnostics D—Display B..Controller Diagnostics E—CAN Bus Info C—Trouble Codes Diagnostics Center Diagnostics Center Diagnostics Center is the one place to find diagnostics for the entire system. Select one of the tabs for more information. Controller Diagnostics » Access Diagnostic Addresses.
CommandCenter™ Controller Diagnostics Controller Diagnostics displays the following information for controllers connected on CAN BUS. Device « Each device in list is identified by Device 1D, CAN Address, and CAN Network location. Codes * Indicates if device has trouble codes. Message Count » Number of CAN messages display has received from controller. Use zero button at bottom of page to reset message count for all devices.
CommandCenter™ Trouble Codes Trouble Codes displays all current and stored codes that have occurred on the system. Select Refresh button to clear, and then retrieve all codes. Select Clear Codes bunion to remove all codes from display. pia ® A=Refresh button B—Clear Codes button Viewing and Sorting Select button next to "View by" to change the way codes are displayed. Available views are: Code « View by “Code” lists all codes on display. Code Type, Details, Status, and Count are all displayed.
CommandCenter™ Readings The following information is available in Readings: Hardware « Displays and Server ~ Part Numbers Serial Numbers Operational Hours » USB Presence Electrical * Switched Voltage * Switched Voltage » Implement and Vehicle CAN Can High GAN Low Other: NOTE, Machine must be equipped to receive certain information, + Radar Input Status + Grandiloquence + implement Switch Status 909LILT1% CAN BUS Information Select Implement CAN for information on GPS receiver, second ISOBARS display, and IS
CommandCenter™ CAN BUS Values Network Status Active * System is working as expected. In addition to display, at least ane controller is connected and communicating on CAN BUS Inactive « Display is not communicating with any other controllers ort CAN BUS. if display is only controller on CAN BUS, Total Message Count increases, but Network Status is inactive, Total Message Count Total message count is number of messages sent over CAN BUS.
CommandCenter™ | Navigate to Users & Access 1. Select Menu. 2. Select System tab. 3. Select Users & Access icon. Sl A—User Profiles Tab D—Edit Button Groups Tab E—View Button Menu — System Tab — User & Access Jon C—Change Profile Button Cc ®E -19-2241 Users & Access Users & Access manages user profile settings to lock users out of certain features. User Profiles « Change display profile and set PIN for administrator Users & Access deepness. Access Groups 1. Select Menu.
CommandCenter™ | EN 150515 Change Active Profile Select Change Profile button and select profile from list. =: NOTE: If a PIN has been created for the administrator profile. if must be entered when switching from Operator Profile to Administrator Profile. ® © Add/Change PIN Select Edit button for Administrator Profile. Select Exchange Profile Button G—View Bunion Add{Change PIN button, Access Groups SOE Access Groups store display features users have access to.
CommandCenter™ Navigate to Layout Manager 1. Select Menu, 2. Select Applications tah. 3. Select Layout Manager icon. NOTE: Layout Manager opens in last used run page. A—Active Set Tab C—Edit Button Bail Run Pages Tab Fou EE one Meninx > Applications Tab > Layout Manager Icon S| Layout Manager Page 15 038E BTS KT&1202 Layout Manager Use Layout Manager to create and modify run pages so important information and functions can be accessed from the main page.
CommandCenter™ | Edit Run Pages in Active Set Select one of the run pages to show a row of buttons for editing that run page. Select Edit button to change the modules on run page. Select Duplicate button to create a new run page with same modules. Select Up and Down buttons to change order of run pages. Run page order is used when cycling through pages on main page. Select Remove button to delete run page from Active Set. Run page Is still in All Run Pages fist, just no longer in Active Set. EN1005.
CommandCenter™ Autocrat Guidance Use Guidance application for steering machines through field along guidance tracks. Guidance can be done manually, or automatically using Autocrat. Manual Guidance (included feature) Manual Guidance. also known as Parallel Tracking, enables operator to steer manually along guidance tracks using onscreen fight bar, map. and audible tones. A Star Fire receiver is required to operate Manual Guidance.
CommandCenter™ Machine Profiles Machine Profiles allow the operator to configure machine dimensions and GPS offsets. These offsets and dimensions are important for system performance Machine Settings If machine is detected by display, machine type is automatically populated. Otherwise, select list box to choose machine type Depending on machine type selected, additional dimensions may be required. « Four Wheel Drive Tractor Front Axis « Distance from articulation point to center of front axle.
CommandCenter™ Implement Profiles Use Implement Profiles to configure Implement Connection Type, Working Width, Dimensions, and Recording Triggers. These offsets and dimensions are important for system performance. Connection Types » Determines the trailing actions of the implement being towed behind machine. Connection Type should reflect the connection type of the current implement. ft should also match one of the machine connection types specified in the Machine Profiles section.
CommandCenter™ Machine Monitor Machine Monitor displays machine specific performance values. Groupings of values include: * Speed and Power + Fuel and Pressure + Temperature * Electrical * Hours NOTE: Values available in each group depend on machine model. Select tabs on left-hand side of the page to switch between groups. Select a value to view a popup of just that value. If a value is not available, dashes will be shown. POORER 12 Machine Monitor Navigate to Machine Monitor 1. Selectmen. 2.
CommandCenter™ Work Recording When Work Recording is ON, map recording and counters that require a recording trigger accumulate. Counters requiring Work Recording include: * Area Worked * Time Worked * Productivity » Average Fuel Per Area * Average Working Speed Select Work Recording in the bottom right hand corner to view a popup window with recording settings. Recording slats is based off the current recording trigger selected in implement Profiles.
CommandCenter™ | Calibrations Use this application to perform wheel slip calibration and radar calibration. For a tractor, perform wheel slip calibration and radar calibration within this application. Radar Calibration A radar device needs to be calibrated when it is first installed on the machine or there is a difference between radar speed and actual ground speed. Currently, the system supports John Deere dual beam radars.
CommandCenter™ Navigate to Controls Setup Controls Setup page allows user to assign device (E) with various implement functions {MH}. Once completed function may be performed by activating assigned device NOTE. Some ISOBARS joysticks may nof be equipped. CAUTION: ISOBARS Controller detected Generation 4 Controls Setup Shortcut Button Improper operation can cause unintended SN—DIAUGS implement movement.
CommandCenter™ CRG Controls From the left-hand side of the Controls Setup page, select one of the following controls: » Tractor joystick Enable or Disable Controls « ISOBARS joystick « Tractor functions * ISOBARS implement * Inuit implement + Function Assignments Tractor functions Depending on the selected control, the following + Fumigation + Device + Input combinations (assignments) are possible: BUSGIRLS Implement Tractor joystick * Function + Device + Input * Input + Source + Function ROBUST joystick Se
CommandCenter™ | Automation Status Automation Status gives operator the ability to control tractor functions externally. Automation Status displays which tractor functions are being controlled and their current status. Example 1 SCV Function status set toc AUTO. Implement actively controls SCV 1. Implement requests SCV flow to be set at 32% in extend direction. 1. Select Menu. 2. Select Applications tab. 3. Select Automation Status icon.
CommandCenter™ ISOBARS VT This John Deere display supports ISOBARS 11783 compatible implements. These implements can be viewed and operated within the ISOBARS Virtual Terminal (VT). When an ISOBARS implement is connected, graphic files for the user interface are loaded into ISOBARS VT. Then ROBUST VT provides a means for the operator to navigate cd ara through and operate all available functions of ISOBARS 2. "Select Application tab implement. 3. Select ISOBARS VT application. Navigate to ISOBARS VT 1.
