Face Access AITP04 Quick Start Guide (Web Operations)
HARDWARE INSTALLATION 2
1 Plug-in the Power Supply and Network Cables Power Supply Network Supply Plug-in the RJ-45 Ethernet and power supply cables into the AITP04 unit and power-ON the AITP04 unit Note: The other end of the power supply cable must be connected to the power supply. The other end of the RJ-45 should be connected to a LAN-connected router, bridge or switch.
Choose an AITP04 Mounting Option A. 2 Wall Mount (incl. in standard packaging) B. Desktop Mount (incl. in standard packaging) C. Gate Mount (incl.
2A Wall-mount the Face Access AITP04 Unit Push all cables through the center-hole of the provided AITP04 Wall Mount Holder Cables AITP04 Wall Mount Holder Fasten the AITP04 to the AITP04 Wall Mount Holder with the 4 screws Fix the provided wall bracket on the wall Wall-mounted AITP04 Wall Bracket Attach the combined AITP04 & AITP04 Wall Mount Holder unit to the wall bracket fixed to the wall 5
2B Desktop-mount the Face Access AITP04 Unit Push all cables through the center-hole of the provided AITP04 Desktop Mount Holder Cables AITP04 Desktop Mount Holder Desktop-mounted AITP04 Fasten the AITP04 to the AITP04 Desktop Mount Holder with the 4 screws 6
2C Gate-mount the Face Access AITP04 Unit Cables Push all cables through the center-hole of the provided tilt bracket Tilt Bracket Gate-mounted AITP04 Attach the tilt bracket (with cables passing through it) to the AITP04 7
2C Gate-mount the Face Access AITP04 Unit Attach the combined AITP04 and tilt bracket unit (with cables passing through it) to the provided pipe of the gate-mount using the 2 screws provided Short Pipe Shaft Gate-Mount Gate-mounted AITP04 Long Pipe Shaft Gate-Mount 8
SOFTWARE CONFIGURATION (Web) 9
1 Wait for Face Access AITP04 Unit’s I.P Address After powering-ON the AITP04 unit, wait till the assigned I.P address from the DHCP server shows on the bottom-right side of the AITP04 display screen.
2 Accessing the AITP04 Unit’s Device Settings (Any Web Browser) 3 Viewing the Live Video Stream of an Face Access AITP04 Unit (Windows’ Internet Explorer Web Browser only) Type in the AITP04’s I.P address and port number 8080 into the Internet Explorer Web browser of a Windows PC. Type in username admin, password admin123 and click on log in.
4 Accessing All AITP04 Unit’s Configuration Settings (Any Web Browser) Click on Configuration to access the configuration settings menu. The configuration settings menu can be found on the left-side pane.
5 Configuring the AITP04 Unit’s Panel Display Settings Click on Configuration → Algorithm → Panel Settings to configure the panel U.
6 Configuring the AITP04 Unit’s Body Temperature and Protective Face Mask Temperature Detection Settings 7 Adding the Users’ Data into the Face Database (Any Web Browser) a) Click on Configuration → Face Database to add users’ data into the face database ClickonConfiguration → Algorithm → CaptureSettingstoconfiguretheBody Temperature and Protective Face Mask detection settings b) Enter a user’s personal ID data, work ID data, contact data, personal ID certification data and work ID certification data c
Upon successful addition of user data, the user’s record appears as shown below – 15
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. -- The distance between user and device should be no less than 20cm. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
