INSTALLATION Manual RF-160 IM-Inst-RF160en v0.
Dedrone Legal Provisions The information contained in these documents is the property of Dedrone GmbH. Any publication, whether in whole or in part, requires prior written approval by Dedrone GmbH. Internal reproduction used solely for the purpose of product evaluation or other proper use is allowed and does not require prior approval. The declaration of conformity is available on request at support@dedrone.com.
Dedrone Content 1 Safety...............................................................................................................................................4 1.1 Symbols..................................................................................................................................................................4 1.2 Intended Use................................................................................................................................................
Safety Dedrone 1 Safety 1.1 Symbols Symbol Explanation Indicates a situation which, if not avoided, can result in property damage Information that is important for a specific goal, but is not safety-relevant Indicates a requirement for meeting a specific goal Desired result A problem that might occur Action to resolve a problem 1.2 Intended Use The RF-160 is a passive, network-attached sensor for the detection of radio frequencies (RF).
Dedrone Safety may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •• Reorient or relocate the receiving antenna.
The RF-160 Dedrone Despite careful construction, electrical devices can cause fires. Do not mount the RF-160 in areas containing highly flammable materials or gases. Do not mount the RF-160 in a potentially explosive atmosphere. Do not install product near any heat sources such as radiators, heaters, exhaust air systems or other equipment (including amplifiers) that produce heat. 2 The RF-160 The RF-160 is a passive, network-attached sensor for the detection of radio frequencies (RF).
Dedrone Scope of Delivery 4 Scope of Delivery Verify that all the parts listed in the scope of delivery are included. If any items are missing, notify your Dedrone Partner. Do not use this product if any component appears to be damaged. Please contact Dedrone in the event of damaged goods. 1 x RF-160 1 x Screwdriver 1 x AC cable with outdoor plug, 16 ft. (5 m) 1 x Outdoor ethernet cable, 32 ft.
Select the Mounting Place Dedrone The detected signals are getting interfered. •• Any excessive heat sources •• Any overhead power lines, power circuits, or electrical lights Electrical discharge can damage the device. Select a secure installation location and mounting position for the device. Ideally, this is a location where the device cannot be interfered with, either intentionally or accidentally.
Dedrone Installation 6 Installation 6.1 Power Supply The RF-160 can use two kinds of power supplies: •• AC power supply with the supplied power plug via a socket (AC 100-240V 50/60 Hz). `` Make sure that the power socket is grounded. `` In Denmark: Apparatets stikprop skal tilsluttes en stikkontakt med jord som giver forbindel- se til stikproppens jord. `` In Finland: Laite on liitettävä suojakoskettimilla varustettuun pistorasiaan. `` In Norway: Apparatet må tilkoples jordet stikkontakt.
Installation 3 Dedrone Thread the connector body over the plug. ]]The plug clicks in and gets fixed in the connector body. 4 Slide the gland to the connector body and screw down the gland nut on the connector body. 6.4 Install the Sensor `` Desired mounting place fulfills the requirements (see chapter 5 Select the Mounting Place, page 7). `` Diameter of the pole: between 1.2 in to 3.1 in (40 mm to 80 mm) Procedure: 1 Open the carton, remove the upper foam.
Dedrone Installation 5 Take out the pole mount. 6 Put the pole mount on the pole. •• To open up the pole mount unscrew the pole fixing screws. 7 Adjust the pole mount in the desired direction and tighten the pole fixing screws appropriately. Only use the supplied screws. 8 Center the pole mount plate over the pole and tighten the aligning screws appropriately. Only use the supplied screws.
Installation 10 Dedrone Place the RF-160 on the pole mount 2 •• Slide the fixing screws in the screw guides of the mounting plate (1). Thereby make sure that the two flaps of the pole mount slides in the slot of the RF-160. •• Tighten the security screw by hand (2). Thereby the sensor is secured from falling down. 1 •• Tighten the fixing screws appropriately. Only use the supplied screws.
Dedrone 12 Integrate the RF-160 in your DroneTracker To operate the RF-160 via the supplied AC cable, connect the AC cable to the AC socket: •• Remove the protective cap from the AC plug. •• Plug the AC cable into the plug (1). 1 ]]The plug clicks into place and the arrow on the plug points to the lock symbol on the socket. •• Lay the cable in the cable guide (2). •• Plug the AC plug into the socket.
Integrate the RF-160 in your DroneTracker Dedrone Requirements: `` RF-160 is installed `` The power supply is working and the button at the RF-160 illuminates blue `` RF-160 is connected to the network `` The IP address of the DroneTracker Server is known Procedure: 1 Start your web-browser and enter the address of your DroneTracker Server. For an optimal use, Dedrone recommends Chrome or Firefox. 2 Log in the DroneTracker UI as an administrator or configurator.
Dedrone Integrate the RF-160 in your DroneTracker 7.2 Integrate the RF-160 via Dedrone Cloud Requirements: `` RF-160 is installed `` The power supply is working and the LED at the RF-160 illuminates blue `` RF-160 is connected to the Dedrone Cloud `` The address of your Dedrone Cloud access is known (provided by Dedrone) `` The registration key of the sensor is available (provided by Dedrone) Procedure: 1 Start your web-browser and enter the address of your Dedrone Cloud.
Cleaning Dedrone 8 Cleaning Wrong cleaner damages the housing The wrong cleaner can damage the housing or antenna of the RF-160. Never use glass cleaner or other solvent cleaner to clean the RF-160. ••Use solvent-free cleaner to clean the RF-160. 9 Decommissioning 9.1 Shut down the RF-160 RF-160 breaks By disconnecting the cable of the power supply without shut down the RF-160, the RF-160 could break. ••Always shut down the RF-160 before disconnecting the cable.
Dedrone Technical Data 10 Technical Data Range (line of sight) 0.65 mi (1.0 km) In ideal conditions up to 1.3 mi (2 km) Device Type Sensor Radio Frequency Omnidirectional passive detection and classification LxWxH 1 ft x 1 ft x 1.3ft (300 mm x 300 mm x 395 mm) Weight 12.2 lb (5.5 kg) Ingress Protection Rating IP65 * Operating Temperature -4 °F to +131 °F (-20 °C to +55 °C) Power Supply AC 100-240V 50/60 Hz max. 1 A or PoE+ IEEE 802.
AIRSPACE SECURITY SOLUTION Dedrone Holding, Inc. Dedrone GmbH +1 415 813-6116 220 Sansome Street Miramstraße 87 +49 561 8617990 San Francisco, CA 94104 34123 Kassel info@dedrone.com USA Germany www.dedrone.
