® The Driving Force in Automation SERVICE MANUAL MINIATURE RGD/RGS SERIES INDEX DRIVES MODELS 40, 50, 70, & 80 RGD/RGS “WARNING” “WARNING” This is a controlled document. It is your responsibility to deliver this information to the end user of the CAMCO indexer. Failure to deliver this, could result in your liability for injury to the user or damage to the machine. For copies of this manual call your Customer Service Representative 800/645-5207.
TABLE OF CONTENTS INTRODUCTION ..............................................................................................................2 WARNINGS AND CAUTIONS .........................................................................................2 OIL SEAL REMOVAL .......................................................................................................2 SPARE PARTS KIT ..........................................................................................................
INTRODUCTION This service manual pertains to the disassembly and assembly of CAMCO’s Miniature RGD Series Index Drives MODELS 40, 50, 70 & 80RGD/RGS. The manual is to be used in conjunction with the General Service Manual which describes the lubrication and general maintenance of CAMCO Index Drives. For your convenience in identifying and ordering spare or replacement parts, a complete Bill of Materials is included in this manual.
looseness. It should not exceed .001 inch.Do not confuse radial loosness with axial endplay. Endplay will be from .03 to .06 as a normal condition. If it exceeds .06 it may require follower replacement. DISASSEMBLY 1. Remove all accessory equipment such as clutches, reducers, sprockets, etc. 2. Drain oil and flush with flushing solvent. Retain any chips or broken pieces that you may find. These may aid in diagnosis. 3. Remove round access cover.
F. Support the side of the cam where the bearing was removed and press or drive the shaft through from the remaining bearing side. This will remove the remaining bearing and cam simultaneously. B. Remove any remaining output bearing from the housing by the same method as described in step “A”. 9. Remove input bearing cups from the cartridges with a wheel puller, by prying or by drilling and tapping for jack screws. 10. Press out all oil seals from both input and output cartridges.
H. If endplay exists, remove shims until there is a small amount of drag from preloading the bearings. In rare instances it may be necessary to remachine the cartridges if all shims are removed and endplay still exists. 4. SETTING THE CAM CAUTION: This mechanism is designed to operate with adjacent followers in close ontact along their entire width with the surface of the cam during the dwell period.
2.) If there is a gap at the tip of the follower the cam should be shifted away from the follower. 5. Install a new access cover.Press in flush with housing. 6. Grease pack the main output bearing with lubricant specified in the “General Service Manual”. D. Apply “Prussian Blue” to entire cam track. E. Rotate the cam shaft slowly with a small handrank to ensure that: 7. Install new oil seals as described in the “General Service Manual”. 1.) Both rollers are in contact with the cam rib in dwell.
HOW TO ORDER PARTS Please refer to parts list shown in this manual. This parts list is for a standard Index Drive. If you feel your drive is nonstandard or you are in doubt you should contact CAMCO Customer Service at (847) 459-5200 and request a Bill of Material for your specific unit based on serial number. CAMCO maintains records on all units for a period of ten years. You may order parts per the standard Bill of Material even if your unit is nonstandard.
40, 50, 70 & 80RGD/RGS SIDE VIEW END VIEW 8
PARTS LIST FOR 40RGD INDEX DRIVE (STANDARD CONFIGURATION) 1 ...................................................... 4MD55426001002 2 ...................................................... 4MB51870007002 ........................................................ 4MA49071007001 3 ...................................................... 4MB51609004006 ........................................................ 4MB51610004008 ........................................................ 4MB51611004010 ......................
PARTS LIST FOR 40RGS INDEX DRIVE (STANDARD CONFIGURATION) 1 ...................................................... 4MD55426001002 2 ...................................................... 4MB51870007002 ........................................................ 4MA49071007001 3 ...................................................... 4MB51614004006 ........................................................ 4MB51615004008 ........................................................ 4MB51616004010 ......................
PARTS LIST FOR 50RGD INDEX DRIVE (STANDARD CONFIGURATION) 1 ...................................................... 5MD55427001002 2 ...................................................... 5MC52018007002 3 ...................................................... 5MC52026004006 ........................................................ 5MC52027004006 ........................................................ 5MC52025004008 ........................................................ 5MC52023004010 ......................
PARTS LIST FOR 50RGS INDEX DRIVE (STANDARD CONFIGURATION) 1 ........................................................... 5MD55427001002 2 ........................................................... 5MC52018007002 ............................................................. 5MC52041004006 ............................................................. 5MC52040004006 ............................................................. 5MC52039004008 .............................................................
PARTS LIST FOR 70RGD INDEX DRIVE (STANDARD CONFIGURATION) 1 ...................................................... 7MG60152001002 2 ...................................................... 7MB60190007002 3 ...................................................... 7MB60253004006 ........................................................ 7MB60254004006 ........................................................ 7MB60255004008 ........................................................ 7MB60256004010 ......................
PARTS LIST FOR 70RGS INDEX DRIVE (STANDARD CONFIGURATION) 1 ...................................................... 7MG60152001002 2 ...................................................... 7MB60190007002 3 ...................................................... 7MB60257004006 ........................................................ 7MB60258004006 ........................................................ 7MB60259004008 ........................................................ 7MB60260004010 ......................
PARTS LIST FOR 80RGD INDEX DRIVE (STANDARD CONFIGURATION) 1 ...................................................... 8MG60210001002 2 ...................................................... 8MB60757007002 ........................................................ 8MC60917007002 3 ...................................................... 8MC60827004006 ........................................................ 8MC60828004008 ........................................................ 8MC60829004010 ......................
PARTS LIST FOR 80RGS INDEX DRIVE (STANDARD CONFIGURATION) 1 ...................................................... 8MG60210001002 2 ...................................................... 8MB60757007002 ........................................................ 8MC60917007002 3 ...................................................... 8MC60831004006 ........................................................ 8MC60832004006 ........................................................ 8MC60833004010 ......................
99 A44547 18 0000 6/99 0064