User's Manual

ManualsBrandsDayton Industrial ManualsBike ComputersBIKE COMPUTER

CM 9.3A (+)

Congratulations on your purchase!

By purchasing the CICLOMASTER CM 9.3A (+) you have acquired an electronic multifunctional sports computer with an integrated

altimeter function, with the highest level of precision and newest digital transmission technology. The CM 9.3A (+) has state of-the-

art electronics, is waterproof and convinces through his high durability.

 which makes it extremely

fault resistant. The CM 9.3A (+) has a Two-in-One system. This means that you can use it with 2 bikes and have the recorded

values displayed separately for each bike or as a total. In this case, the CM 9.3A (+) automatically identifies immediately, after the

first wheel rotations, which of the two bikes is being used.

As another special features the CM 9.3A (+) has an optional cadence measurement and an optional heart rate measurement (for

this you need separately available accessories ).

In order to use all functions of the CM 9.3A (+) in the correct way, please read through this operating manual carefully.

Content:

- CICLOMASTER CM 8.3A

- battery type CR 2032

- battery cap

- handlebar bracket

- speed-transmitter

- cable ties for mounting

- spoke magnet

- short instruction

CM 9.3A (+) has three modes: Bike 1, Bike 2, and Non-Bike mode.

To switch from one mode to another, simultaneously press the right and left buttons briefly (switching is only possible if speed SPD

= 0). In the Non-Bike mode, only bicycle independent functions will be displayed.

CM 9.3A (+) has an automatic energy save mode: If signals are received 

during this time, the display will be switched off (in the non-bike mode it will be turned off after 15 hours.)

By pressing any button the display will be switched on again.

Because of the new digital transmission technique, the transmitters have to be initialized before using

CM 9.3A (+) for the first time. We recommend initializing the transmitters before mounting the CM 9.3A (+) on the bike.

The handlebar bracket can be mounted on the handlebar or on the stem. For a using the handlebar on the stem, unscrew the

screws on the back and rotate the rear part by 90 degrees.

2.1 Mounting of optional cadence-set

Mount the handlebar unit as described above.

-ties yet). Mount the cadence-magnet on the crank (max. distance 3

mm). Important! The magnet must point directly towards the mark on the transmitter.

Now switch CM 9.3A (+) cadence measuring on and  if not done yet  initialize the transmitter (see chap.5).

Turn the crank a few times to check if the mounting has been done correctly so that CM 9.3A (+) receives the signal.

Now tighten the cable-ties.

Summary of content (10 pages)

PAGE 1
CM 9.3A (+) Congratulations on your purchase! By purchasing the CICLOMASTER CM 9.3A (+) you have acquired an electronic multifunctional sports computer with an integrated altimeter function, with the highest level of precision and newest digital transmission technology. The CM 9.3A (+) has state of-theart electronics, is waterproof and convinces through his high durability.
PAGE 2
.2 Putting on the heart rate transmission belt Warning: whoever carries out sport should have a general medical check up on his/her general state of health – especially beginners, persons older than 35 years of age and anyone who has suffered from illnesses or injuries in the past. It is recommended that a doctor is consulted in any case in the presence of risk factors, such as smoking, high blood pressure, high cholesterol values, diabetes, lack of exercise and excess weight.
PAGE 3
If CM 9.3A (+) is not in the Bike 1 Mode (no symbol in the center display), switch on the Bike 1-Mode (simultaneously press right and left buttons). Enter setting mode by pressing center button for 5 seconds. Display shows „SET BIKE1‟. To quit setting mode press again center button for 5 seconds in any setting. The normal bike mode will be displayed. (To change the display to german language, press left button short twice, display shows ‚LANGUAGE‟.
PAGE 4
UNIT m Set unit of measurement for altitude. Default: m (meters) Here you can select whether the indication is meter (m) or feet (ft). UNIT °C Set unit of measurement for temperature. Default: °Celsius Here you can adjust heit (F). whether the indication is Celsius (C) or Fahren- SET BIKE1 / SET RAD1 Adjustment of bike-specific values, e.g. total distance, circumference, unit and more for bike 1. Choose with center button.
PAGE 5
Set with right button, store with left button Here you can choose whether the display should show kilometres (km/h) or miles (m/h). Bike kg Here you can enter the weight of your bike in kg. CAD OFF/TRITT AUS Switch cadence on/off (ON/AN – OFF/AUS). Default: OFF/AUS Here you can switch on/off the cadence measuring. To use this function you need the optional cadence-set (available at your local dealer). Power ON/Power AN Switch power on/off (ON/AN – OFF/AUS).
PAGE 6
Fitness / Fitness Adjustment of the fitness level. Default: 3 . Range 1-4, corresponding to the following levels: 1 – low fitness 2 – average fitness 3 – good fitness 4 – high fitness Here you set your personal fitness level, necessary for the CICLOInZone®-calculation. Sex / Geschlecht Change between m = male and f = female. The sex is needed for the CICLOInZone®-calculation and the calorie consumption.
PAGE 7
Powerdown / STROMSPAR Switch on the powerdown-mode (e.g. before changing of the battery, to save the values). To switch it on, press right and left button short simultaneously, display fades out and CM 9.3A (+) is in powerdown-mode. By short pressing of any button, CM 9.3A (+) starts again and shows normal mode. Reset / Löschen Here you can delete all values (including all values of the recorded tours or the initializations).
PAGE 8
Night light display: To switch on the light for 5 seconds, press left button 4 seconds. To activate the light manager (i.e. in the next 5 hours light is switched on for 5 sec. automatically with every button press) press left button 8 seconds. Display shows ‚LIGHT MGR ON‟. To deactivate the light manager, press again left button 8 seconds, display shows ‚LIGHT MGR OFF‟. Note: light requires a lot of battery power, so if you use it often, battery life will be reduced. CM 9.
PAGE 9
We offer a guarantee for 2 years from the date of purchase on the CM 8.3A. The guarantee is limited to material and processing faults. Broken transmitters, or damages of wasted parts of CM 9.3A (+) are excluded from the guarantee. The guarantee is valid only if the computer, with accessories, has been handled and maintained carefully and according to operating instructions. The guarantee will take place through changes of or repairing the defective parts.
PAGE 10
This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.