User's Manual

ManualsBrandsDAYTON AUDIO ManualsElectronicsBluetooth Hybrid Amplifier

Important Safety Instructions

To reduce the risk of electric shock, do not remove cover. No user

serviceable parts inside. Refer servicing to qualied personnel. To

reduce the risk of re and shock do not expose unit to rain or moisture.

The unit should be connected to an earth grounded AC electrical

socket. The unit should be operated in a well ventilated area. Minimum

clearance is 2 inches from the ventilation openings.

HYBRID STEREO

TUBE AMPLIFIER

Model: HTA100BT User Manual

Dayton Audio

Last Revised: 4/20/2020

daytonaudio.com

tel + 937.743.8248

info@daytonaudio.com

705 Pleasant Valley Dr.

Springboro, OH 45066

USA

5-Year Limited Warranty

See daytonaudio.com for details

Speciﬁcations:

Power Output: ............................. 50 watts RMS x 2 into 4 ohms

Total Harmonic Distortion: ........ 0.5% @ 50W per channel

Minimum Speaker Impedance: .. 4 ohm

Frequency Response: ................ 20-20,000 Hz, ±2 dB

Channel Separation:

................... 50 dB

Preampli

ﬁer Tube: ...................... 6U1 x2 6F2 x2

Bluetooth Version:

...................... 4.2

Input Impedance:

........................ 47k ohms (minimum)

Input Sensitivity: ......................... 250 mV

Dimensions:

................................ 6.6

″ H x 11.5″ W x 10.6″ D

Weight: ........................................ 11 lbs

FCC Statement

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(a) This device may not cause harmful interference.

(b) This device must accept any interference received, including interference that

may cause undesired operation.

2. FCC Radiation Exposure Statement: Mobile device.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. In order to avoid the possibility of exceeding the FCC radio frequency expo-

sure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during

normal operation.

Summary of content (3 pages)

PAGE 1
Speciﬁcations: Power Output:.............................. 50 watts RMS x 2 into 4 ohms Total Harmonic Distortion:......... 0.5% @ 50W per channel Minimum Speaker Impedance:... 4 ohm Frequency Response:................. 20-20,000 Hz, ±2 dB Channel Separation:.................... 50 dB Preamplifier Tube:....................... 6U1 x2 6F2 x2 Bluetooth Version:....................... 4.2 Input Impedance:......................... 47k ohms (minimum) HYBRID STEREO TUBE AMPLIFIER Input Sensitivity:..............
PAGE 2
Front Panel Thank you for purchasing the Dayton Audio HTA100BT Hybrid Stereo Tube ency. Multiple input options including USB media playback are available, and Bluetooth 4.2 1 2 3 4 Features: • 50W per channel RMS into each channel at a 4 ohm load • Audiophile quality sound with less than 0.5% THD @ 50W • Bluetooth 4.2 wireless connectivity • RCA mono subwoofer output • Brushed aluminum housing lends a clean, modern look 5 • Short circuit protection circuitry Front Panel: 1. Power 2. Source 3. 4.
PAGE 3
FCC Warning Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.