DATECS BluePad-55 v2 USER GUIDE BLUEPAD-55 v2 User Guide © 2018 Datecs, Ltd.
1 DATECS All rights reserved. No part of the contents of this document may be reproduced or transmitted in any form without the written permission of Datecs, Ltd. The information contained in this document is subject to change without notice. Although Datecs has attempted to ensure the accuracy of the contents of this document, this document may include errors or omissions. The examples and sample programs are for illustration only and may not be suited for your purpose.
1 DATECS Version Data 1.0.0 2.0.0 2.1.0 2.2.0 2.3.0 14.11.2018 28.05.2020 10.06.2020 21.09.2020 02.02.
1 DATECS Contents REGULATORY ..................................................................................................................................................................... 6 FCC NOTICE ........................................................................................................................................................................... 6 PREFACE .........................................................................................................................
1 DATECS BLANK DISPLAY ........................................................................................................................................................................ 23 KEYPAD DOES NOT RESPOND ..................................................................................................................................................... 23 TRANSACTIONS FAIL TO PROCESS ..............................................................................................................
1 DATECS REGULATORY FCC NOTICE FCC ID: YRW-SUMUPPRO This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
1 DATECS in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided.
1 DATECS PREFACE This guide is the primary source of information for setting up and installing BLUEPAD-55 v2. Audience This guide provides simple descriptions of BLUEPAD-55 v2 features, as well as basic information for anyone installing and configuring BLUEPAD-55 v2. Organization This guide is organized as follows: Chapter 1, Overview. Provides an overview of the BLUEPAD-55 v2. Chapter 2, Specifications. Discusses power requirements and dimensions of BLUEPAD55 v2, etc. Chapter 3, Setup.
1 DATECS Related Documentation To learn more BLUEPAD-55 v2, refer to the following set of documents: • BLUEPAD-55 v2 Physical Security Features • BLUEPAD-55 v2 Firmware API Specifications • BLUEPAD-55 v2 Software Design Specifications CONVENTIONS Various conventions are used to help you quickly identify special formatting. Table 1 describes these conventions and provides examples of their use. Table 1 Document Conventions Convention Meaning Blue Text in blue indicates terms thatare cross references.
1 DATECS Overview This chapter provides a brief description of Datecs’s BLUEPAD-55 v2 device. BLUEPAD-55 v2 The BLUEPAD-55 v2 unit is a handheld PIN pad with an integrated smart and contactless card reader an optional Bluetooth module designed to be used with a variety of PDA’s, offering advanced security and smart card processing capabilities. BLUEPAD-55 v2 supports both symmetric encryption algorithms (DES, 3DES, and AES) and asymmetric encryption (RSA).
1 DATECS Features and Benefits Exceptional Ease of Use • Bold, ergonomic design is sleek, stylish, and lightweight for conveniently handing the unit to the consumer for PIN entry. • Intuitive interface and large, colored control keys simplify training and reduce support requests. • Highly readable display handles multiple languages.
1 DATECS Device Specifications Processor Memory Application Memory ARM Cortex® M3 Security Microcontroller 64KB Internal ROM 384KB Internal RAM 1MB Internal Flash 4MB Serial Flash 128MB NAND Flash (Optional) 512MB NAND Flash (Optional) Display and Touchscreen • Type – LCD, capacitive touchscreen, 65K colors • Size - 2.
1 DATECS Device Operation Figure 1 1. 2. 3. 4. 5. 6. 7. 8.
1 DATECS The battery is charged by the USB power adapter, from connector position “6”. The BLUEPAD-55 v2 is switched on and off by pressing the There are four general purpose LEDs: button. The BLUEPAD-55 v2 comes with a USB communication cable. The USB communication cable is connected to the BLUEPAD-55’s v2 mini-USB connector 1. For reading of an ICC, the card has to be inserted manually into the card slot 3.
1 DATECS DEV SN - BLUEPAD-55 v2 serial number USIP SN - USIP serial number USIP VER - USIP version ISBL VER - USIP Boot loader version HAL VER - USIP Hardware Abstraction Layer (HAL) version LOAD VER - Secure Boot Loader (SBL) version and name FW VER - Firmware version and name PROM VER - Prompts version APPL VER - Application version and name PKFA VER - Version of the public key used for firmware authentication PKAA VER - Version of the public key used for application authentication PKKA VER - Version of
1 DATECS KEYS DOWNLOAD To download the Acquirer Initial Keys (AIK) the PINPAD has to be set in Keys Download Mode, in which it exchanges information in a secure way through the RS-232 interface using proprietary communication protocol.To exit the mode the C button has to be pressed. CLEAR DEA KEYS Deletes the customer’s DEA key hierarchy. EXIT Exit the service menu forwarding the control to the application.
1 DATECS SETTINGS IN APPLICATION(DEPENDS OF THE APPLICATION) RS SPEED 115200* USB MODE DISABLE*/DEVICE/HOST BLUETOOTH Settings Mode: ENABLE/DISABLE ADDR: MAC ADDRESS of the Bluetooth NAME: Bluetooth name PASS: Bluetooth password PAIR: DISCOVERABLE/HIDDEN AUTO: ENABLE/DISABLE VER: Bluetooth firmware version MASTER RESET: return to default settings PAIRING FW UPDATE AUTO OFF 60min*/120min/180min/240min/DISABLE/1min//5min/10min/ 15min/30min/45min *Default settings BLUEPAD-55 V2 USER GUIDE 1 DATECS
1 DATECS How to insert/remove SIM and SAM cards Location of the SIM and SAM tray is show on Figure 2. To open device's SIM and SAM tray, insert a eject tool into the hole beside the tray. Figure 2 The BLUEPAD-55 v2 SIM and SAM tray is support only Nano size cards. When tray is opened slide out (Figure 3) and insert cards (Figure 4). Place cards and slide in the tray and close (Figure 5).
1 DATECS Figure 5 SIM and SAM card must be placed on correct positions, they are shown on Figure 4.
1 DATECS Smart Card Reader Use The smart card transaction procedure can vary depending on the application loaded on the BLUEPAD55 v2. Verify the proper procedure with your application provider before performing a smart card transaction. To Conduct a Smart Card Transaction 1 Position a smart card with the gold contacts facing upward. 2 Insert it into the ICC card reader slot in a smooth, continuous motion until it seats firmly.
1 DATECS Contactless Card Reading The contactless card transaction procedure can vary depending on the application loaded on the BLUEPAD-55 v2. Verify the proper procedure with your application provider before performing a contactless card transaction. In order to use the Contactless card reading function, special software must be used. Please contact your distributor in order to get the latest demo application and SDK. To Conduct a Contactless Credit/Debit Card Transaction 1.
1 DATECS Display with touchscreen The device is equipped with display, which is have capacitive touchscreen. The touchscreen is using for signature capture or easy Menu navigation.
1 DATECS Troubleshooting Guidelines This chapter lists typical examples of malfunction you may encounter while operating your BLUEPAD55 v2 unit and steps you can take to resolve them. The troubleshooting guidelines provided in the following section are included to assist successful installation and configuration of BLUEPAD-55 v2 units. If you are having problems operating your BLUEPAD-55 v2 unit, please read through these troubleshooting examples.
1 DATECS Maintenance and Cleaning BLUEPAD-55 v2 units have no user-serviceable parts. To clean the unit, use a clean cloth slightly dampened with water and a drop or two of mild soap. For stubborn stains, use alcohol or an alcohol-based cleaner. Do not attempt to clean the card readers. Doing so can void any warranty. For card reader service, contact your Datecs distributor or service provider. Never use thinner, trichloroethylene, or ketone-based solvents – they can deteriorate plastic or rubber parts.
