User Manual ESC/POS PRINTER DPP-450
1 DATECS DPP-450 User manual THE INFORMATION IN THIS DOCUMENT CANNOT BE REPRODUCED IN ANY MECHANICAL, ELECTRICAL OR ELECTRONIC WAY AND UNDER ANY CIRCUMSTANCES WITHOUT THE WRITTEN CONSENT FROM DATECS LTD.
1 DATECS DPP-450 User manual Legal Notice “Made for iPod,” “Made for iPhone,” and Made for iPad” mean that an electronic accesory has been designed to connect specifically to iPod, iPhone, or iPad, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible fort he operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accesory with iPod, iPhone, or iPad may affect wireless performance.
1 DATECS DPP-450 User manual This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
1 DATECS DPP-450 User manual CONTENTS 1. Introduction............................................................................................................. 6 2. Features ................................................................................................................. 6 3. Technical specification............................................................................................ 7 4. General view.................................................................................
1 DATECS DPP-450 User manual 1. Introduction DATECS DPP-450 is a mobile ESC/POS and LABEL thermal printer. It can be used in dynamic working conditions and its abundant built-in features allow it to be widely used for different applications. Printer can quickly and easily print text and/or graphics, depending on customer’s needs – barcodes, logo, etc. 2.
1 DATECS DPP-450 User manual 3.
1 DATECS DPP-450 User manual LED Indication • Paper end or paper out • Cover open • Low battery • Print head overheating Audio Indications Electro-magnetic buzzer Display • LCD 128 x 64 dots • LED backlight Buttons • Power button • Print button • Feed button Memory 4MB Flash(option) Buffer Size up to 128 kB Periphery • RFID card reader: • MiFARE Mini • MiFARE Classic 1K / 4K • MiFARE Ultra-Light / UltraLight-C Emulation • ESC/POS • Eltron • ZEBRA* Power Supply AC Adapter • Input: AC: 100-
1 DATECS DPP-450 User manual Drop Test Height: 1m 3 times on each of the 6 faces 3 times on each of the 4 edges OS compatibility iOS, Android OS, BlackBerry OS, Windows OS, Win CE, Windows Mobile, Windows Phone Accessories • Neck strap • Metal belt clip • Carrying case • Single battery charger 9
1 DATECS DPP-450 User manual 4. General view 4.
1 DATECS DPP-450 User manual 4.
1 DATECS DPP-450 User manual Software (Drivers & SDK ): Because of the continually evolving Driver & SDK to support new mobile devices, Drivers & SDK are distributed online and is available for download at our website indicated below. For details on using the DPP-450 Drivers & SDK, please refer to the SDK’s documentation. http://www.datecs.bg/en/products/DPP-450/2/264# 5. Getting started The DPP-450 allows you to printer information from your PDA & Smart phone.
1 DATECS DPP-450 User manual 5.1 Charge DPP-450 The DPP-450 uses a Lithium-Ion rechargeable battery pack. To prevent electrical damage to the DPP-450 and/or battery pack, please use approved AC Charger only. Charging time is 3 hours from empty to full charge. When the battery is fully charged the device can print 150m paper roll, this is 3.5 rolls standart for DPP-450.
1 DATECS DPP-450 User manual Insert cable to dc jack to start charging. When the device is turn on(holding turn on/off button), in display will show “CHG” text and greed led “CHARGE” is blink. ECS/POS Ready CHG 5.2 Diagnostic information • Holding button while power on for ~ 0.5 sec (first sound signal) – short selftest. • Holding button while power on for ~ 2.5 sec (second sound signal) – start dump mode. All input data are printed hexadecimal and as text.
1 DATECS DPP-450 User manual When the paper cover is open drop the new roll of thermal media. With green lever can choose size of thermal paper. To choose paper size – pull up lever and push on right for small paper or left for big. When lever is in max. left position insert new paper(if size is different from last one) and pull up lever and push right until reach paper, then release lever.
1 DATECS DPP-450 User manual Right paper position Close paper cover 16
1 DATECS DPP-450 User manual Slide peeler Peeler setting for label paper. Peeler setting for paper roll.
1 DATECS DPP-450 User manual 5.4 Mounting belt clip Using two screws. 5.5 Self-Test • Holding button while power on for ~ 0.5 sec (first sound signal) – short selftest. The DPP-450 has a built-in test pattern that shows the printer’s current configuration as well as the various resident printer fonts. The self-test can also be used as a troubleshooting tool to determine printing problems or battery level. The steps below show how the self-test is printed activated.
1 DATECS DPP-450 User manual • Holding button while power on for ~ 5.5 sec (third sound signal) – self-test.
1 DATECS DPP-450 User manual 5.6 Page Mode In page mode the result of incoming commands is forwarded to a reserved memory area (page). The page place and size is defined using command ESC W. Command GS T selects the print direction in this page. At the end the collected information is printed using one of the commands, provided for this. Commands ESC FF and GS FF print only the currently defined page, but command ESC Z prints the area between the first and last line containing at least one black point.
1 DATECS DPP-450 User manual 2: Send data 3: Request data >4: Application specific Status: One byte: Bit 0 Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 0 1 No error Error occured ACK (Packet accepted) NACK (Packed not accepted) Channel and command OK Wrong channel or command Battery OK Low battery Printing head OK Printing head too hot Paper OK Out of paper Not defined Printer ready Printer busy Bit 7 is set, if: • There are unprinted lines in the print buffer. • There are bytes in the print buffer.
1 DATECS DPP-450 User manual Command 4 Get printer status. 5 data bytes returned in response: BufferHi BufferLo PrStatus Volt Temperature BufferHi High byte of the count of free bytes in input buffer. BufferLo Low byte of the count of free bytes in input buffer. PrStatus Printer status. The following bits defined: Bit 0 Battery low Bit 1 Too hot Bit 2 No paper Volt The battery voltage in units 0.1V Temperature The head temperature in degrees Celsius.
1 DATECS DPP-450 User manual Then press FEED button, to enter Hardware menu. Device will prining current settings. The LCD in hardware configuration menu: FACTORY DEFAULT MEM. SWITCHES: BAUD RATE: IrDA BAUD RATE: With button “PRINT” can move down and with “FEED” can enter in selected.
1 DATECS DPP-450 User manual FACTORY DEFAULT YES NO MEM.
1 DATECS DPP-450 • • 2 min. 5 min.
1 DATECS DPP-450 USB DEV. CLASS • • User manual Changing the USB device class of the printer Printer/Serial Printer Serial SAVE & EXIT MENU 5.10 List of commands 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 BEL HT LF FF CR DC2 = DC3 DC3 + DC3 DC3 A DC3 B DC3 C DC3 D DC3 F DC3 L DC3 M DC3 P DC3 p DC3 v CAN ESC FF ESC RS ESC SP ESC # ESC $ ESC % 27 28 29 30 31 32 33 34 35 36 37 39 40 ESC & ESC ! ESC * ESC + ESC ESC .
1 DATECS DPP-450 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 ESC D ESC E ESC F ESC G ESC I ESC J ESC L ESC N ESC R ESC S ESC T ESC U ESC V ESC W ESC X ESC Y ESC Z ESC \ ESC ] ESC ^ ESC _ ESC ` ESC a ESC b ESC c5 ESC d ESC i ESC o ESC pair= ESC pwd= ESC r ESC s ESC u ESC v ESC x 76 77 78 79 80 81 82 83 84 85 86 87 88 ESC y ESC { GS FF GS $ GS ) GS * GS / GS : GS B GS C GS H GS L GS Q User manual Setting horizontal tab position Specifying/Cance
1 DATECS DPP-450 89 90 91 92 93 94 GS R GS S GS T GS U GS W GS X 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 GS Z GS \ GS ^ GS c GS f GS h GS k GS p GS q GS w GS x FS ! FS & FS FS .
1 DATECS DPP-450 User manual Bluetooth version: The DPP-450 Bluetooth version uses Bluetooth® wireless technology to connect to Bluetooth enable devices. iOS devices: Connect to LineaTAB. Start – LibraryDemo on iPad. Connect LineaTab to iPad(Figure 4). After this press settings button. Turn on DPP-450 Bluetooth printer. From setting menu press Discover printers, and wait to find printers. When is found press on selected printer and wait connect.
1 DATECS DPP-450 User manual On “Print” menu can printing via Bluetooth connection: - Print Self-test - Demo fonts - Demo barcodes - Demo graphics To terminate the BT connection, press settings menu and name of printer. When is close connection the “tick” will disappearing. 5.
1 DATECS DPP-450 User manual 31