DATECS BlueLite v2 User Manual
1 DATECS BLUELITE V2 USER MANUAL THE INFORMATION IN THIS DOCUMENT CANNOT BE REPRODUCED IN ANY MECHANICAL, ELECTRICAL OR ELECTRONIC WAY AND UNDER ANY CIRCUMSTANCES WITHOUT THE WRITTEN CONSENT FROM DATECS LTD. Address: 4 Datecs Street, Sofia 1592, Bulgaria Phone: +359 2 816 55 50 Fax: +359 2 816 55 65 E-mail: export@datecs.
1 DATECS BLUELITE V2 USER MANUAL REVISION HISTORY Version Data Change description 1.0.0 05.01.2018 First Release 1.1.0 22.01.2019 Updated specification and added section “Scan to Pairing” 1.2.0 13.11.
1 DATECS BLUELITE V2 USER MANUAL REGULATORY FCC ID: YRW-BLUELITEV2 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
1 DATECS BLUELITE V2 USER MANUAL CONTENTS TECHNICAL SPECIFICATIONS ................................................................................................................................................... 6 GENERAL VIEW ........................................................................................................................................................................ 7 GETTING STARTED ............................................................................................
1 DATECS BLUELITE V2 USER MANUAL TECHNICAL SPECIFICATIONS ARM Cortex® M3 Security Microcontroller Processor 64KB Internal ROM 256KB Internal RAM 1MB Internal Flash 4MB Serial Flash Memory Application Memory Keypad • ON / OFF key • Bluetooth pairing button Magnetic Card Reader • 3-track bi-directional reading • ISO 7810, 7811 and 7813 ISO7816, EMV L1 certified Smart Card Reader • AMEX ExpressPay • Discover D-PAS • MasterCard Contactless • VISA PayWave Contactless Card Reader for payment applicati
1 DATECS BLUELITE V2 USER MANUAL GENERAL VIEW Figure 1 7
1 DATECS BLUELITE V2 USER MANUAL 1. Micro USB port 2. Button for Bluetooth pairing 3. Magnetic Card Reader 4. On/Off Button 5. Contactless reader 6. Opening for inserting smart card 7.
1 DATECS BLUELITE V2 USER MANUAL GETTING STARTED BlueLite v2 has rechargeable Li-Po battery. Can be charge from micro USB port. Before first use, battery must be fully charged. If the device is fully discharged, charging time to fully charged would be approx. 1 hour and 30min. Charging form USB adapter: Figure 2 Main battery replacement: To replace the main battery of BlueLite v2 please contact with your local Datecs representative or service provider.
1 DATECS BLUELITE V2 USER MANUAL PERIODIC INSPECTION AND MAINTENANCE The following inspections must be performed on a regular basis after initial receipt and installation of BlueLite v2: • There are no visual indications for trying unauthorized opening of the device • There are no unusual wires connected to the ICC acceptor or any of the ports on the terminal. • There is no shim device in the ICC acceptor slot. • The terminal serial number (on the label) corresponds to the one in the inventory paperwork.
1 DATECS BLUELITE V2 USER MANUAL OPERATION MODES For start operating with BlueLite v2 is need to be paired to another Bluetooth BLE device with installed application. For downloading the latest SDKs for iOS, Android and Windows please contact with your distributor. Application download mode, System mode and Clearing Bluetooth paring info Application download mode - to enter application download mode on the BlueLite v2, the power button has to be maintained pressed.
1 DATECS BLUELITE V2 USER MANUAL LED indication Description Device operating No indication Device is turned off First red LED is flashing Device is turned on Second red LED is continuously light on Device battery is charging Operating modes when is press power button First white LED is continuously light on Device will go to normal operating mode Second white LED is continuously light on Device will enter in Boot loader Third white LED is continuously light on Device will enter in System mod
1 DATECS BLUELITE V2 USER MANUAL Bluetooth Pairing Turn on BlueLite v2, connect it to PC via USB cable. When device is connected to PC, will create virtual COM port. Check on device manager on which port is connected. After that run the special application for PC (Fig. 3). Press “Search” button on the app, and in right side will be show all available COM ports. Select on which is connected device, then press “Connect to device”. From Bluetooth management on mobile device (equipped with BLE 4.
1 DATECS BLUELITE V2 USER MANUAL Bluetooth Pairing to Apple device (iOS) with BLE (Scan to Pairing) 1. Turn on BlueLite v2 (hold On/Off button, around ~2sec). 2. Run the iOS application, go to the settings “Scan barcode”: Figure 8 Then the camera of the phone will be activate 3. Scan the serial number on the label of BlueLite v2 with back camera. 4. Then of the screens on both devices will be showed the “Pairing Request”. Figure 9 5.
1 DATECS BLUELITE V2 USER MANUAL Magnetic cards reading The BlueLite v2 has a built-in magnetic card reader. The card reader incorporates a (3) track magnetic read head, requiring a single swipe to read field data from all three tracks. The magnetic reading head faces down, towards the top of the bottom cover of the cradle. When swiping the card into the reader, the magnetic stripe must be facing as shown in the figure below.
1 DATECS BLUELITE V2 USER MANUAL Contactless cards reading The contactless card transaction procedure can vary depending on the application loaded on the BlueLite v2. Verify the proper procedure with your application provider before performing a contactless card transaction. In order to use the Contactless card reading function, special software must be used. Please contact your distributor in order to get the latest demo application and SDK. To Conduct a Contactless Credit/Debit Card Transaction 1.
1 DATECS BLUELITE V2 USER MANUAL Smart cards reading The smart card transaction procedure can vary depending on the application loaded on the BlueLite v2. Verify the proper procedure with your application provider before performing a smart card transaction. To Conduct a Smart Card Transaction 1 Position a smart card with the gold contacts facing upward. 2 Insert it into the ICC card reader slot in a smooth, continuous motion until it seats firmly.
1 DATECS BLUELITE V2 USER MANUAL CARE, MAINTENANCE AND WARRANTY • • • • • • Keep the BlueLite v2 side of the reach of small children. Keep the BlueLite v2 dry. Precipitation, humidity and liquid contain minerals that will corrode electronic circuits. Do not use or store in dusty or dirty areas. Do not drop or knock BlueLite v2 Do not open the BlueLite v2. Only qualified personnel can open the device and make repair. If the BlueLite v2 is not working, please contact with your dealer.