Datasheet

ManualsBrandsDataVideo Manualsaudio & home theatreRMC-140

2005/9/5

Ì¿´´§ñÐ®»ª·»© Þ±¨ º±®

ÍÛóèðð

ÎÓÝóïìð

Û®®±®ÿ

ËÍÛÎ ÓßÒËßÔ

Ø¬¬°æññ©©©ò¼¿¬¿ª·¼»±ó¬»µò½±³

Warnings and Precautions

1. Read all of these warnings and save them for later reference.

2. Follow all warnings and instructions marked on this unit.

3. Unplug this unit from the wall outlet before cleaning. Do not

use liquid or aerosol cleaners. Use a damp cloth for cleaning.

4. Do not use this unit in or near water.

5. Do not place this unit on an unstable cart, stand, or table. The

unit may fall, causing serious damage.

6. Slots and openings on the cabinet top, back, and bottom are

provided for ventilation. To ensure safe and reliable operation

of this unit, and to protect it from overheating, do not block or

cover these openings. Do not place this unit on a bed, sofa,

rug, or similar surface, as the ventilation openings on the

bottom of the cabinet will be blocked. This unit should never be

placed near or over a heat register or radiator. This unit should

not be placed in a built-in installation unless proper ventilation

is provided.

7. This product should only be operated from the type of power

source indicated on the marking label of the AC adapter. If you

are not sure of the type of power available, consult your

Datavideo dealer or your local power company.

8. Do not allow anything to rest on the power cord. Do not locate

this unit where the power cord will be walked on, rolled over, or

otherwise stressed.

9. If an extension cord must be used with this unit, make sure that

the total of the ampere ratings on the products plugged into the

extension cord do not exceed the extension cords rating.

10. Make sure that the total amperes of all the units that are

plugged into a single wall outlet do not exceed 15 amperes.

Summary of content (9 pages)

PAGE 1
Warnings and Precautions 1. Read all of these warnings and save them for later reference. 2. Follow all warnings and instructions marked on this unit. Ì¿´´§ñÐ®»ª·»© Þ±¨ º±® ÍÛóèðð ÎÓÝóïìð 3. Unplug this unit from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 4. Do not use this unit in or near water. 5. Do not place this unit on an unstable cart, stand, or table. The unit may fall, causing serious damage. 6.
PAGE 2
11. Never push objects of any kind into this unit through the cabinet ventilation slots, as they may touch dangerous voltage Table of Contents points or short out parts that could result in risk of fire or electric shock. Never spill liquid of any kind onto or into this unit. 12. Except as specifically explained elsewhere in this manual, do WHATS IN THE BOX? .................................................................4 not attempt to service this product yourself.
PAGE 3
Whats in the box? Introduction Thank you for purchasing the RMC-140. This is an accessory for the SE-800, and it can also be used for security camera monitoring. In order to bring out the maximum performance of this software, we recommend that you spend some time reading this manual carefully. 1. RMC-140 2. User Manual 3. RS232 cable x 1 4. BNC 1.2m cable * 5 5. AC/DC Power Adapter Product Overview The RMC-140 is especially designed for control by the SE 800, via RS-232 port.
PAGE 4
Features Interface Next source preview Combine 4 different video sources into one video output 1 2 (4 display modes, Quad, POP, PIP, and full screen.) Next transition effect indicator 3 4 Tally light indicator 1. 4 composite input 2. Monitor output (Quad, POP, PIP & Next selectable) 3. Full screen next source preview output, Effect and Tally light indicators 4. Power connector (DV12V) 9 8 6 5 7 5. Tally light signal out (15pin & 3.5mm jack) 6. RS-232 input from SE-800 7.
PAGE 5
Installation 1. Connect four monitor outputs from SE-800, Or loop thru from TLM-404. Plug in the power adapter, and connect to the power. Now RMC-140 is ready to use.
PAGE 6
Display Modes SET UP Menu The four display modes of the RMC 140 are: Next Source PIP The RMC 140 has a simple Set Up Menu, which is navigated with the +, -, Up, Down and Menu buttons. To call up the menu press the menu button. Shows a full screen display of the cued up source. Shows a full screen of the Live Source with a PIP of the cued up source. Quad POP Within the menu there are Color Processor Settings for each input, and a Video Output Setting. Color Processor Settings.
PAGE 7
Video Output Settings The Video Output can be set to Same or Separate. Same will feed identical signals to both outputs, whereas Separate will feed whichever display mode you have selected to the Main Output (PIP, QUAD, POP, Next Source), and a full screen next source preview to the Next Source Output. Then press the menu button, to enter the settings menu Main Output This will always show the chosen display pattern i.e. PIP, POP, QUAD or Next Source.
PAGE 8
Sample connection diagrams Example 1: RMC-140 and SE-800 Application Specification Video Formats Analog Composite NTSC or PAL (NTSC and PAL are separate models) Video Inputs 4 Composite Video Output 1 Composite (Quad, POP, PIP, Next source preview) 1 Composite (Full screen next source preview) RS-232 Data Control Port From SE-800- Connecting Datavideo SE-800 RS-232 By pass- For other RS-232 remote control devices Tally Light Signal Out 1 15pin 4 3.5mm mini jack Video Bandwidth Composite 4.
PAGE 9
Product registration Go on line www.datavideo.info/product_reg.htm for product registration See the warranty card for warranty period Service and Support It is our goal to make your products ownership a satisfying experience. Our supporting staff is available to assist you in setting up and operating your system. Please refer to our web site www.datavideo-tek.com for answers to common questions, support requests or contact your local office below. Datavideo Corporation (USA) 12300-U East Washington Blvd.