ITC100 8 Channel Intercom / Talkback System User’s Guide http:// www.datavideotek.
Warnings and Precautions 1. Read all of these warnings and save them for later reference. 2. Follow all warnings and instructions marked on this unit. 3. Unplug this unit from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 4. Do not use this unit in or near water. 5. Do not place this unit on an unstable cart, stand, or table. The unit may fall, causing serious damage. 6.
Warranty Datavideo warrants that the equipment it manufactures shall be free from defects in material and workmanship for a period of 12 months from the date of product purchased. If equipment fails due to such defects, Datavideo will, at its option, repair or provide a replacement for the defective part or product.
Contents WARNINGS AND PRECAUTIONS 1 WARRANTY 2 INTRODUCTION 2 WHAT’S IN THE PACKAGE 3 FRONT PANEL CONNECTIONS 4 REAR PANEL CONNECTIONS 6 ITC100SL SLAVE UNIT 7 USING THE ITC100 WITH THE SE800 / RMC140 9 USING THE ITC100 WITH THE SE800 / RMC90 10 USING THE ITC100 WITH THE SE500 11 ITC100 TALLY INPUT PIN CROSS REFERENCE 12 SPECIFICATIONS 13 SERVICE AND SUPPORT 15 What’s in the Package 1. ITC100 main unit x 1 2. ITC100SL Slave Unit x 4 3.
Front Panel: On / Off Switch Powers the ITC100 On / Off. Red LED indicates that unit is switched on. XLR Microphone Socket Combined XLR / ¼” (6.3mm) Jack Microphone Input for either a Condenser or Dynamic Gooseneck Microphone. XLR supports Condenser Microphones ¼” (6.3mm) Jack supports Dynamic. Headphone Socket ¼ “ / 6.3mm Stereo Headphone Socket for conventional headphones. Plugging in headphones will disable the builtin speaker Microphone / Headset Socket 3.
Channel Buttons 1~8 Opens communication with individual channels. More than 1 channel can be active at any given time, active channels are illuminated red. All active channels will hear any communication from the operator or from any other active channel. The buttons will also indicate if any channel is paging, the paging channel will flash in orange until the page is answered. MUTE Button Mutes all communication from the base station or any channel. N.B.
Rear Panel: Channel Input / Output XLR Sockets Each of the 8 channels has an XLR connector that carries bidirectional signals between the ITC100 and ITC100SL. All connections are contained within the one cable. Channels 1 ~ 4 are supplied tally light information from tally A; channels 5 ~ 8 are supplied tally light information from tally B. Tally Inputs A & B Tally Inputs A & B are configured for direct connection to the Datavideo RMC140, RMC90 or SE500.
ITC100SL Slave Unit : XLR Connection Connects the ITC100SL to the ITC100 Base Station. Power, tally and bidirectional audio are all carried through the same cable. Call Button Sends a paging message to the ITC100 Base Station. The channel button will flash orange and there will be an audible tone, each time the button is pressed.
Mic / Headphone Socket The ITC100SL has both a 3.5mm and 2.5mm Mic / Headset socket. A standard 3.5mm Mic / Headset can be used, or a Motorola type 2.5mm Mic / headset could be used if preferred. External Tally LED Socket An external tally display (TD1) can be connected to the ITC100SL. This enables the tally light to be positioned in a more convenient place, such as on top of the camera. When the channel is LIVE the LED will be RED, and when the channel is CUED the LED will be AMBER. N.B.
Using the ITC100 with the SE800 / RMC140: The ITC100 is an ideal accessory for the Datavideo SE800 / SE800AV Vision Mixer. The SE800 has four channels, so in the diagram below we have four camera crew, each with an ITC100SL The RS232 output from the SE800 connects to the RMC140; this provides the status of the SE800. The RMC140 Tally Out connects to the ITC100 Tally Input A. Tally Input A provides tally information to channels 1 ~ 4.
Using the ITC100 with the SE800 / RMC90: Using the Datavideo SE800 / SE800AV Vision Mixer in combination with the RMC90 remote control makes live production really simple. The RS232 output from the SE800 connects to the RMC90; this provides the status of the SE800. The RMC90 Tally Out connects to the ITC100 Tally Input A. Tally Input A provides tally information to channels 1 ~ 4.
Using the ITC100 with the SE500: The ITC100 is an ideal accessory for the Datavideo SE500 Vision Mixer. The SE500 has four channels, so in the diagram below we have four camera crew, each with an ITC100SL. The SE500 Tally Out connects to the ITC100 Tally Input A. Tally Input A provides tally information to channels 1 ~ 4. When the camera is live the cameraman will see a red light, when a camera is cued up the cameraman will see an amber light.
ITC100 Tally Input Pin Cross Reference If you are using the ITC100 with a Datavideo RMC140, RMC90 or SE500 you do not need to worry about tally information, as it is automatically sent to the ITC100. If you are using the ITC100 with other equipment the following tables explain the pin configurations of Tally A and Tally B. Contact closure between the relevant Pin number and ground will illuminate the LED.
Specification: ITC100 Base Station Specification POWER 12V 1.5A TALLY 2 x 15 Pin SubD Sockets for Tally A and Tally B MIC / HEADSET 3.5mm Stereo Jack Socket for combination Headphone / Microphone Headset Impedance 8~600 ohms 100mW(min) INPUTS / HEADPHONE OUTPUTS ¼” (6.3mm) Stereo Headphone Socket Headset Impedance 8~600 ohms 100mW(min) LIGHT SOCKET 3 pin XLR connector. Pin2: 12V, Pin3: GND. (12V DC) Light power consumption 12V/100mA(max). MICROPHONE 3 Pin XLR / ¼” (6.
ITC100SL SLAVE Unit Specification INPUT 5 Pin XLR Connector MIC / HEADSET SOCKET 3.5mm Stereo Jack Socket for combination Headphone / Microphone Headset Impedance 8~600 ohms 100mW(min) Microphone Level 67dB Or 2.5mm Stereo Jack Socket, for Motorola Mobile Phone type headset / microphone TALLY OUT SOCKET 3.
Service and Support It is our goal to make your products ownership a satisfying experience. Our supporting staff is available to assist you in setting up and operating your system. Please refer to our web site www.datavideotek.com for answers to common questions, support requests or contact your local office below. Datavideo Corporation (USA) 12300U East Washington Blvd., Whittier, CA 90606 USA Tel: +1 562 696 2324 contactus@datavideo.us www.datavideo.
