User's Manual

ManualsBrandsDatamatic ManualsElectronicsFIREFLY D2300

Datamatic.com, Ltd. 2000 - 2001

Chapter 1

FIREFLY Installation

Installation Preparation

Installation Overview - Sensor End

1. Set Auto Advance to “Off” from the Main Menu, Option ‘C’.

2. Install the optical sensor. (See instructions “Installing the Optical Sensor” on

page 2).

3. Program the FIREFLY MIU using the PPU (See instructions “Programming the

FIREFLY MIU” on page Error! Bookmark not defined.).

4. Choose a method and mount the FIREFLY MIU.

5. Set the FIREFLY interegation mode to Install Read to verify the FIREFLY MIU is

transmitting properly by using the ROADRUNNER to receive an RF message.

Installation Considerations

1. Signal distance varies depending on the location of the MIU. FIREFLYs installed

above-ground generally transmit the greatest distance.

2. The material of a pit or vault lid affects the transmission range. For example, a

transmitter has a greater range sending from a pit with a plastic lid than a cast iron

lid.

3. Lids with holes of a diameter of one inch make it possible to mount of the FIREFLY

MIU through the lid. This can increase transmission range significantly.

4. Complete field installation of an MIU takes 5-10 minutes, depending on the meter

location and mounting application.

Summary of content (9 pages)

PAGE 1
Chapter 1 1 FIREFLY Installation Installation Preparation Installation Overview - Sensor End 1. Set Auto Advance to “Off” from the Main Menu, Option ‘C’. 2. Install the optical sensor. (See instructions “Installing the Optical Sensor” on page 2). 3. Program the FIREFLY MIU using the PPU (See instructions “Programming the FIREFLY MIU” on page Error! Bookmark not defined.). 4. Choose a method and mount the FIREFLY MIU. 5.
PAGE 2
xxxxxxxxxxx REFERENCE MANUAL 5. If the lid has a hole for the unit, use the cap and wing nut assembly (“lid lock” pictured at right). Ensure that enough space exists between the box lid and the ground for the unit to sit. If not, remove some of the dirt from the bottom of the box. Do not overtighten lid locks. Water FIREFLY Installation Installing the Optical Sensor-End FIREFLY Meter Preparation 1. Remove meter box lid. 2. Survey the meter, checking lid, hole depth, and overall cleanliness. 3.
PAGE 3
Chapter 1 FIREFLY Installation 3 Ve r i f yi ng Se ns or Pl a c e me nt Powe r 1 [ 44] Powe r 2 [ 62] Powe r 3 [ 86] St a t us : [ Suc c e s s ] Te s t Aga i n? Y/ N The values shown are in decimal and the test keys on Power Level 2 (P2). A successful test and sensor target placement is achieved when the P2 value is 60 or greater. *After completing the sensor background test, determine if another alcohol cleaning is needed on the register face prior to installation of the sensor.
PAGE 4
xxxxxxxxxxx REFERENCE MANUAL 7. A full cure on the seal is achieved in 24 - 96 hours. Do not touch, pull, move, or handle the sensor in any way during this period. 8. Apply approved adhesive around the sensor to seal it completely in case the pit fills with water prior to the 24 - 96 hour cure time, or if the meter face is curved and not flat. Note: If the sensor is initially misplaced, do not attempt to remove the sensor by twisting the sensor body.
PAGE 5
Chapter 1 FIREFLY Installation 5 Installing the Wire End FIREFLY with a Logical Switch The FIREFLY Logical Switch MUST be handled with care at all times. A drop or shock of any kind could effect the performance of the Logical Switch. The Logical Switch is compatible with FIREFLY Firmware 0108 and above. Use the following instructions to install FIREFLYS: 1. Set Reading Mode to Install Mode. Connect Wires with the FIREFLY and Logical Switch 2.
PAGE 6
xxxxxxxxxxx REFERENCE MANUAL 9. Verify the meter #. 10. Enter the visual reading. 11. View Current Settings screen--Check normal values entered on template and battery voltage--Enter. 12. View FF Options screen--Select Save and Exit and press Enter. 13. Select Meter brand and size. 14. When ROADRUNNER has returned to the route, turn off the PPU. 15. Interrogate (press I) MIU using manual mode—you should now get a reading. Mount the FIREFLY 16. Mount the MIU to a stake, wall or as predetermined. 17.
PAGE 7
Chapter 1 FIREFLY Installation Installing Disk Decals 1. Remove nameplate on meter. 2. Clean rotating disk target area with 99% isopropyl alcohol. 3. Place approved decal* on target area. Be sure the edge of the decal is not overhanging on the disk and it is centered of the FIREFLY optical sensors. 4. The user needs to smooth the decal on the plate by applying pressure with his/her thumb. Note: Be sure not to touch the adhesive side of the decal as the oil from the skin can cause it not to adhere. 5.
PAGE 8
xxxxxxxxxxx REFERENCE MANUAL 6. Choose one of the following three options to connect the wires to the 240VAC terminals on the meter. n n n Option A. Use fuse clip to attach wires to the 240VAC terminals on the meter. Option B. Use soldering to attach two wires to the 240VAC terminals on the meter. Option C. Use female insulated crimp connector to connect the wires to the 240VAC terminals on the meter. Note: If connectors are used in place of soldering, use UL-certified crimper.
PAGE 9
Chapter 1 FIREFLY Installation Gas FIREFLY Installation Installing the Gas FIREFLY 1. Remove meter index cover. 2. Ensure that no gasket material remains on the meter. 3. Remove the meter index. 4. Install the meter index onto the front of the Gas FIREFLY, ensuring that the rotating shaft seats into the index crank. 5. Install the gas FIREFLY onto the meter, ensuring that the rotating shaft engages the index drive. 6. Place the index cover gasket onto the inner surface of the index cover. 7.