3 1 DATALOGIC JOYA™ X2 Bluetooth communication data. If tapping on the “Close” button the Bluetooth Manager Device window will be closed. 4. Tap on the “Discovery” button to enter the related window; then, tap on the “Scan” button to run the Discovery procedure: Once the Discovery procedure has been completed, select the desired Bluetooth device from the list. It is also possible to digit (12 hexadecimal digits) the Bluetooth address of the desired device by tapping on the “Add” button.
USE AND FUNCTIONING 3 The “ActiveSync” button starts communication with a PC equipped with a Bluetooth antenna and the related ActiveSync. 6. Hide the Bluetooth Manager Device window by tapping on the icon available on each window or close it through the “Close” button available in the “Me” window (see step 3 of this procedure).
DATALOGIC JOYA™ X2 3 1 3.14.5 FTP Server Setup The Datalogic JOYA™ X2 Operating System includes a File Transfer Protocol (FTP) server. FTP is used for copying files to and from remote computer systems over a network using TCP/IP. You can establish a connection to your Datalogic JOYA™ X2 using its FTP Server through the WLAN using the WiFi radio Proceed as follows: 1. Create a registry file (extension .reg) to setup and enable FTP Server communication.
USE AND FUNCTIONING 3 3.15 BACKUP DIRECTORY FILE MANAGEMENT All of the Windows CE 6.0 system files reside in RAM (volatile memory) except for the Backup directory, which resides in FLASH (non-volatile memory). Therefore the contents of the Backup directory are persistent even if the mobile computer is rebooted or the battery pack is changed. You can save your more important files that you don't want to lose due to mobile computer reboot, in the Backup directory or create a sub-directory within Backup.
3 1 74 DATALOGIC JOYA™ X2
USE AND FUNCTIONING 3 3.16 FIRMWARE UPDATE The Datalogic JOYA™ X2 is equipped with a tool that implements a firmware update service. This tool, called Datalogic Updater (DLUpdater), is compatible with all hardware versions of the Datalogic WindowsCE 6.0 models: An update can be explicitly invoked by running the application DLUpdater.exe, provided together with the update file DLUpdate.zip. The update must be contained in the root.
DATALOGIC JOYA™ X2 3 1 3.16.2 Firmware Update Procedure 1. Download the update from the web site (see previous par.). It is a zip file containing the files: • DLUpdater.exe – that starts the update; • DLUpdate.zip – archive file containing the updated firmware; 2. Copy the files DLUpdater.exe and DLUpdate.zip in the root. 3. Open the root on the terminal and run DLUpdater.exe by double tap the icon (JOYA™ X2 Plus) or by ActiveSync/Mobile Companion (JOYA™ X2 Basic). 4.
USE AND FUNCTIONING 3 3.17 DAATALOGIC CONFIGURATION UTILITY Datalogic Configuration Utility (DCU) is a Datalogic Windows-based utility tool allowing the uploading, modifying and downloading of the configuration of a Datalogic device. Configuration settings include Scanner, Control Panel, and Datalogic Desktop Utility (DDU). The DCU installer is downloadable from the Datalogic website (http://www.datalogic.com/eng/support-services/automaticdata-capture/downloads/software-utilities-sw-2.html).
DATALOGIC JOYA™ X2 4 1 4 MAINTENANCE Battery packs are not initially charged. Therefore the initial operation to perform is to charge them. See below. NOTE CAUTION 4.1 By default, the battery pack is disconnected at the factory to avoid damage due to excessive draining. Annual replacement of rechargeable battery pack avoids possible risks or abnormalities and ensures maximum performance.
MAINTENANCE 4 Even if the storage temperature range is wider, In order to achieve the longest battery life, store the terminal and the spare batteries between 20 to 30 ºC (68 to 86 ºF). NOTE 4.2 JOYA™ X2 should be charged at an ambient temperature between 0 - 35º C to achieve the maximum charging rate. Never charge the main device or spare batteries in a closed space where excessive heat can build up. REPLACING THE BATTERY PACK To correctly replace the battery pack, proceed as follows. 1.
4 1 DATALOGIC JOYA™ X2 2. Remove the cover and then the battery pack, using the proper plastic strips. Pay attention when disconnecting the connector. 3. Install the new battery pack, first insert the connector respecting the right way, then the upper side, finally the bottom side, leaving the plastic strip available for future replace.
MAINTENANCE 4. 4 For correct locking, first insert the upper part of the battery cover, then the lower and screw the two screws placed on the back bottom.
4 1 DATALOGIC JOYA™ X2 To install, charge and/or do any other action on the battery, follow this manual. WARNING The battery pack may get hot, explode, ignite, and/or cause serious injury if exposed to abusive conditions. If the battery pack is replaced with an improper type, there is risk of explosion.
MAINTENANCE 4 In case of leakage of liquid from the battery, avoid contact with liquid the skin or eyes. If the contact occurs, immediately wash the affected area with water and consult a doctor. WARNING Do not solder directly onto the battery pack. Do not expose the battery pack to liquids. Avoid any knocks or excessive vibrations. If the device or the battery is dropped, especially on a hard surface, you should take it to the nearest Authorised Repair Centre for inspection before continuing to use it.
DATALOGIC JOYA™ X2 5 1 5 JOYA CRADLE DISPENSER 5.
JOYA CRADLE DISPENSER 5.3 5 INSTALLATION REQUIREMENTS The figure below represents an 8 JOYA™ X2 Cradle Dispenser Base Unit organized in a single column. JOYA™ X2 will be inserted into the JOYA Cradle Dispensers are at a minimum height of approximately 40 cm. from the floor and a maximum height of about 160 cm. from the floor.
DATALOGIC JOYA™ X2 5 1 5.3.1 Base Unit Construction Details All of the dimensional quotes necessary for building and correctly mounting the supporting crosspieces and fixing blocks for the JOYA Cradle Dispensers are indicated. The zoom of the upper edge of the supporting crosspiece indicates the necessity of reducing the radius of this edge as much as possible in order to provide a stable contact surface for the upper cover of the JOYA Cradle Dispenser.
JOYA CRADLE DISPENSER 5 Suggestion: The cradle fixing blocks shown in the figures are mounted to the supporting crosspieces under the JOYA Cradle Dispensers. Their purpose is to prevent the Cradle Dispensers from falling inside the cabinet during the mounting phase in which the JOYA Cradle Dispensers may not be correctly positioned before fixing them. 5.3.2 JOYA Cradle Dispenser Supports JOYA Cradle Dispensers are supported inside the Base Unit from crosspieces fixed to the side panels of the cabinet.
5 1 5.3.3 DATALOGIC JOYA™ X2 Internal Cabinet Space and Openings The space between the rear of the JOYA Cradle Dispensers and the back part of the cabinet must be left for two reasons: • it must be possible to retrieve objects that accidentally fall through the cradles from the floor behind the cabinet. • there must be a zone for air to freely circulate behind the JOYA Cradle Dispensers to aid their cooling during operation.
JOYA CRADLE DISPENSER 5 The opening at the top of the cabinet must be covered with a grill or mesh, which allows air to flow freely but protects against access to the inside of the cabinet. In this way the power supplies can not be reached externally. Power Supplies • Single 300 W power supply capable of supplying all 8 Cradle Dispensers (91ACC1000 Power Supply 12V 300W).
DATALOGIC JOYA™ X2 5 1 5.3.7 Wiring To wire the JOYA Cradle Dispensers, pre-wired power junction cables are provided as accessories (91ACC0730 Power Junction Cable I90x/3 Cradle -8 pcs.), which are ready to be connected to the power connector at the bottom of the JOYA Cradle Dispenser.
JOYA CRADLE DISPENSER 5 These wiring connections must be made with particular care and meet or exceed the nominal current and power specifications; the current flowing through them is 2.5 A per JOYA Cradle Dispenser. The wires must meet the Safety Normatives currently in force. The following table indicates the maximum current specifications for some wire conductor sections according to the EN 60950 Electrical Safety Normative. Maximum Current 10 A 16 A 25 A Wire Section 1 mm² 1.5 mm² 2.
DATALOGIC JOYA™ X2 5 1 5.3.8 Cable to Power Supply Connection All 12 Vdc power supply connections, both the main power cable and the power junction cables must be made according to the following requirements: Power Junction Cable Connection Wires Brown +12V Blue ground Yellow-Green 5.3.
JOYA CRADLE DISPENSER 5 JOYA Cradle Dispenser Cabinet, the relative electrical wiring and connection to the AC power line must be made according to the Safety Normative currently in force. The following paragraphs contain some particularly important considerations to keep in mind.
5 1 DATALOGIC JOYA™ X2 5.3.11 Connection to AC Line Voltage If connection to the AC power line is made with a plug at the end of the cable, the outlet to which it is inserted must be close by and easily accessible. The outlet must also be rated for the maximum power consumption, which can be considered equal to the nominal power of the connected power supplies.
JOYA CRADLE DISPENSER 5.4 5 JOYA™ X2 CRADLE DISPENSER FIRMWARE JOYA Cradle Dispenser is provided with a full operational Firmware, therefore it doesn’t require any kind of software devoloping activitiy Instead, the behaviour of the JOYA Cradle Dispenser could be controlled at high level using the JOYA™ X2. In SDK Tools is furnished the JOYA Cradle tool program, to upgrade JOYA Cradle Dispenser firmware release. 5.4.1 JOYA Cradle Tool installation By using ActiveSync copy in the \BACKUP\CTOOLS folder
DATALOGIC JOYA™ X2 5 1 The screen displays the JOYA Cradle Tool version and the mode to interact with the cradle (Read or Upgrade). Use the touch screen or: • • • • 5.4.3 Use the upper left key (F1) to select the tab. Use the upper right key (F2) to browse in the screen. Use the “e” key (ENTER) to quit. Use the “=” key (ESC) to select the language (when language is focused). Reading firmware version Select the “Read”.
JOYA CRADLE DISPENSER 5 Cradle locks terminal in the slot and unlock after a successful reading. If read fails, unlock the terminal by approaching a magnet to the sensitive area (see picture below). 5.4.4 Firmware update procedure This is a very uncommon procedure. To perform the firmware update you should be advised by Datalogic which will provide the upgrading firmware file CpodC2.HEX CAUTION Copy in the \Backup folder the file • CpodC2.
5 1 DATALOGIC JOYA™ X2 Select the “Upgrade” key and insert the terminal into the rightmost slot of the cradle. The cradle locks the terminal and JOYA Cradle Tool transfer firmware. During this period, slot led flashes. At the end, the terminal top flashes three times; approach a magnet to the sensitive area to unlock and extract the terminal.
JOYA CRADLE DISPENSER 5 JOYA Cradle Tool shows a suitable message to inform user if update is correctly completed or an error has been occurred.
DATALOGIC JOYA™ X2 5 1 5.5 JOYA™X2/JOYA CRADLE DISPENSER CONNECTION JOYA Cradle Dispenser is equipped with an electrical-serial connection, used to exchange command and response with JOYA™ X2. The communications between the terminal inserted into the slot and the slot itself are performed by means of a special “RPC like command-response” protocol. 5.6 CONFIGURATION JOYA Cradle Dispenser should be previously configured using an apposite program: JOYA Cradle Tool (see SDK Help for more information).
JOYA CRADLE DISPENSER 5 All other commands could be developed by developers using JOYA SDK.
DATALOGIC JOYA™ X2 6 1 6 6.1 TECHNICAL FEATURES TM JOYA X2 TECHNICAL DATASHEET WIRELESS COMMUNICATIONS LOCAL AREA NETWORK (WLAN) IEEE 802.11 b/g/n; WiFi Security Standards, WEP, WPA, TKIP, WPA2, CCX 4 compatible. DECODING CAPABILITY 1D / LINEAR CODES Auto discriminates all standard 1D codes including GS1 DataBar™ linear codes. ELECTRICAL BATTERY* Removable battery pack with rechargeable Li-polymer batteries ENVIRONMENTAL DROP RESISTANCE** TEMPERATURE Withstands drops from 1.
TECHNICAL FEATURES 6 READING PERFORMANCE READER READING INDICATORS 1D Linear CCD imager engine; Scan rate: 50 scans/sec Beeper (Polyphonic audio codec); Green Spot “On Code” good reading feedback (Datalogic patented feature). SAFETY & REGULATORY AGENCY APPROVALS The product meets necessary safety and regulatory approvals for its intended use. ENVIRONMENTAL COMPLIANCE Complies to EU RoHS.
Test codes here. Pag.
105
8 GLOSSARY Access Point A device that provides transparent access between Ethernet wired networks and IEEE 802.11 interoperable radio-equipped mobile units. Hand-held mobile computers, PDAs or other devices equipped with radio cards, communicate with wired networks using Access Points (AP). The mobile unit (mobile computer) may roam among the APs in the same subnet while maintaining a continuous, seamless connection to the wired network.
Liquid Crystal Display (LCD) A display that uses liquid crystal sealed between two glass plates. The crystals are excited by precise electrical charges, causing them to reflect light outside according to their bias. They use little electricity and react relatively quickly. They require external light to reflect their information to the user. Light Emitting Diode (LED) A low power electronic light source commonly used as an indicator light.
INDEX A Accessories; 17 ActiveSync® Remote; 65 J JOYA cradle dispenser; 81 M B Backup Directory File Management; 70 Bluetooth® Manager Device Setup; 66 C Charging the Batteries; 75 Cleaning the Mobile Computer; 80 Connections; 18 Control Panel; 57 Conventions; 1 D Data Capture; 41 Data Capture Configuration; 48 DATALOGIC CONFIGURATION UTILITY; 74 Datalogic JOYA™ X2 Description; 15 Description of the Keys; 44 E End User License Agreement; v F Firmware Update; 72 FTP Server Setup; 69 Maintenance; 75 Micro
Windows Connections; 65 WLAN Connection; 20 WPAN Connections; 21 DRAFT 109
DRAFT
www.datalogic.com © 2014 Datalogic ADC, Inc. All rights reserved. Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries, including the U.S.A. and the E.U. Datalogic ADC, S.r.l. Via S.