1.1 INTRODUCTION LYNX DESCRIPTION The Lynx contains the most innovative technical features, providing them to the user in an ergonomic and elegant form factor. The accelerometer, the vibrator alert and the 3 LEDs help to do not waste time in the configuration and usage of the product. Working with the Lynx becomes an easy pleasure. The great aesthetics does not put the rubustness on a second level.The Lynx has been deisgned for surviving to industrial environmental, outside and inside the four walls.
1.2 AVAILABLE MODELS The brand new Lynx is available in different models depending on the options it is equipped with. All options are listed below: communication options: 802.11 b/g/n radio, Bluetooth®, GSM data capture options: laser, 2D imager compute options: Windows Mobile 6.5 keyboard options: numeric, qwerty For further details about the Lynx models refer to the web site: www.adc.datalogic.com. For further information regarding Windows Embedded Handheld refer to the website: http://www.
Lynx with Bluetooth v2.0, UMTS HSPA+ Voice and Data, Assisted GPS, Wi-Fi 802.11 b/g/n, Decodified Laser (SE955), Camera, Windows Mobile 6.5, 46-Key QWERTY 944400006 Lynx 00N0WI-1Q1-MEN0 Lynx with Bluetooth v2.0, Wi-Fi 802.11 b/g/n, 2D Imager (4500) Wide Aspect, Camera, Windows Mobile 6.5, 46-Key QWERTY 944400007 Lynx H2N0WI-1Q1-MEN0 Lynx with Bluetooth v2.0, UMTS HSPA+ Voice and Data, Assisted GPS, Wi-Fi 802.11 b/g/n, 2D Imager (4500) Wide Aspect, Camera, Windows Mobile 6.
1.3 PACKAGE CONTENTS The Lynx package contains: 1 Lynx PDA 1 Lynx quick start guide 1 rechargeable battery pack (standard for Wi-Fi models, high cap for UMTS models) 1 power supply with regional plugs 1 Lanyard 1 guitar pick stylus Any other packages will contain the accessories necessary for the Lynx connection to the host computer and to the network: the cradle, one or more connection cables.
Rechargeable battery packs are not initially charged. Therefore the first operation to perform is to charge them. See paragraph 오류! NOTE 참조 원본을 찾을 수 없습니다..
1.4 INSERTING MICROSD CARD Lynx supports microSD memory cards. To access the microSD card slot and insert the card, proceed as follows: 1. Turn off the Lynx. 2. Shift the battery latch to the left and remove the battery pack: 3.
4. Shift the card to the right to lock it into the cardholder; close the card slot: 5. First insert the bottom (contacts) and then the upper side of the battery pack into the slot. Press until the battery latch clicks..
1.4.1 Removing the MicroSD Card To remove the microSD card, follow the steps above to access the microSD card cage under the battery, and remove it from microSD slot. Follow proper ESD precautions to avoid damaging microprocessors in the Lynx or the microSD card itself. CAUTION the Proper ESD precautions include, but are not limited to, working on an ESD mat and ensuring that the operator is properly grounded. Do not force the card.
1.5 INSTALLING THE SIM CARD To correctly insert the SIM Card, proceed as follows: 1. Turn off the Lynx. 2. Shift the battery latch to the left and remove the battery pack: 3. Insert the SIM card with the contacts downwards: 4. First insert the bottom (contacts) and then the upper side of the battery pack into the slot. Press until the battery latch clicks.
Follow proper ESD precautions to avoid damaging the SIM card. Proper ESD precautions include, but are not limited to, working on an ESD mat and ensuring that the operator is properly grounded. CAUTION Do not force the card. If you feel resistance, remove the card, check the orientation, and reinsert it. Do not use the SIM card slot for any other accessories. 1.5.1 Removing the SIM Card To remove the SIM card, follow the steps above to access the SIM area, and remove it from its slot.
1.6 ACCESSORIES Cradles 94A150036 Dock, Single Slot, Lynx 94A150037 Charger, 4 Slot Dock, Lynx 94A150038 Dock, Ethernet 4 Slot, Lynx 94A150039 Charger, 4 Slot Battery, Lynx Batteries 94ACC0064 Battery, Standard Capacity, Lynx 94ACC0065 Battery, High Capacity, Lynx Power Supply 94A051975 Power Adapter, 12 to 24v Pwr Plug 2.1mm 94A051976 Adapter, Pwr Jack 2.1mm To Handylink 94ACC1380 Power Supply, Micro USB 94ACC1381 Power Supply, Dock, PWR Plug 2.
Use only a Datalogic ADC-approved power supply and cables. Use of an alternative power supply will invalidate any approval given to this device and may be dangerous.
2. BATTERIES AND MAINTENANCE Rechargeable backup batteries and battery packs are not initially charged. Therefore the initial operation to perform is to charge them. See below. NOTE By default, the battery pack is disconnected at the factory to avoid damage due to excessive draining. CAUTION 1.1 Annual replacement of rechargeable battery pack avoids possible risks or abnormalities and ensures maximum performance.
It’s recommended to charge batteries before first use. NOTE Risk of explosion if battery is replaced by an incorrective type. Dispose of used batteries according to the instructions. CAUTION Il y a risque d’explosion si la batterie est remplacée par une batterie de type incorrect. CAUTION Mettre au rebut les batteris usagées conformément aux instructions. Avoid storing batteries for long periods in a state of full charge or very low charge.
The Lynx could get warm during charging, this is normal and does not mean a malfunction. NOTE Use only a USB-IF compliant USB port as a charging source.
1.2 REPLACING THE BATTERY PACK To correctly replace the battery pack, proceed as follows. 1. Turn off the Lynx. 2. Shift the battery latch to the left and remove the battery pack: 3. Install the new battery pack, first insert the bottom (contacts) and then the upper side of the battery pack into the slot. Press until the battery latch clicks.
Installing, charging and/or any other action should be done by authorized personnel and following this manual. WARNING The battery pack may get hot, explode, ignite, and/or cause serious injury if exposed to abusive conditions. If the battery pack is replaced with an improper type, there is risk of explosion.
WARNING Do not disassemble or modify (i.e. bend, crush or deform) the battery pack. The battery pack contains safety and protection devices, which, if damaged, may cause the battery pack to generate heat, explode or ignite. In case of leakage of liquid from the battery, avoid contact with liquid the skin or eyes. If the contact occurs, immediately wash the affected area with water and consult a doctor. Do not solder directly onto the battery pack. Do not expose the battery pack to liquids.
1.3 CLEANING THE PDA Periodically clean the Lynx with a slightly dampened cloth. Do not use alcohol, corrosive products or solvents.
3. CONNECTIONS 1.1 USB CONNECTION You can use the standard micro USB cable 94A051968 or the Datalogic Handylink cable 94A051970 to directly connect the Lynx to a host computer to transfer data through the USB interface. A C B Key: A Host computer B Standard Micro USB cable 94A051968/ 94A051970 Handylink USB Client Cable C Lynx Connection through the cable complies to the 1.1 USB standard.
The Single Dock can be connected to the Host by means of the Micro-B USB cord 94A051968. Once the host has been turned on, insert the Lynx PDA into the cradle. A C B D Key: A Host computer C 94A150036 Lynx Single Slot Dock B 94A051968 Micro USB Client Cable D 94ACC1381 Power Adapter Connection through the cradle complies to 1.1 USB standard. NOTE The actual data transfer speed can be appreciably lower than the maximum theoretical speed.
1.2 CONNECTION TO USB PERIPHERALS To connect the Lynx to a keyboard or a memory, connect the terminal to the Datalogic 94A051969 cable or to the Datalogic 94A051971 cable (together with a standard A to micro A USB cable). For all these devices maximum current withdrawal must be below 100mA.
Connect the Single Slot Dock to the peripheral by means of a Micro-A USB cord, or use a Micro-A to Std-A receptacle USB adapter such as Datalogic 94A051969 (together with a standard USB cable if needed). B A C D E A USB Peripheral (memory) D Standard A to Micro A USB Cable B Lynx Single Slot Dock E 94ACC1381 Power Adapter C 94A051969 Micro USB Host Cable Lynx works with most of mentioned USB peripherals. Datalogic can not guarantee the operations of Lynx with all devices on the market.
1.3 RS232 CONNECTION You can use the Datalogic 94A051972 cable to directly connect the Lynx to a host computer to transfer data through the RS232 interface A C B Key: A Host computer B 94A051972 Handylink Micro RS232 Client Cable C Lynx The Single Slot Dock can be connected to the Host by means of a standard null modem cable such as Datalogic 94A051020 CAB-427 for 9-pin connections. Once the Host has been turned on, insert the Lynx PDA into the cradle.
1.4 WLAN CONNECTION Lynx 802.11 b/g/n radio models can communicate with the host using the on-board radio frequency component and an Access Point connected to the host computer. For models using the 802.11 b/g/n radio, you can find information about the applet for radio configuration: http://www.summitdata.com/SCU.htm. To launch this utility you can tap the specific icon if it's visible on the taskbar or you can select the menu item: Start->Programs->Summit and tap the ‘SCU’ icon.
802.11 b/g/n radio module is on by default, in order to avoid wasting energy, you can switch it off using the SCU. NOTE NOTE Suspending the terminal powers off the 802.11 b/g/n radio and drops the radio connection. When the terminal resumes, depending on the radio power mode and security protocol selected, it may take up to 30 seconds for the 802.11 b/g/n radio driver to re-associate the radio to the network.
1.5 WPAN CONNECTIONS Lynx Bluetooth®, models can communicate with a Bluetooth®, device, such as a printer, within a range of 10 m, using the on-board Bluetooth®, module. B A Key: A) Lynx B) Bluetooth®, printer NOTE In order to extend battery life, the Bluetooth®, module is off by default. If you need to have Bluetooth® working, the module must be powered on using the Wireless Communications applet (see par. 오류! 참조 원본을 찾을 수 없습니다.), and perform the Discovery procedure (see par. 오류! 참조 원본을 찾을 수 없습니다.).
NOTE
1.6 WWAN CONNECTION Lynx GSM models enhance your connectivity solutions giving you an opening to an international wireless infrastructure that is the global standard. GSM (Global System for Mobile communications) is a digital mobile phone system based on TDMA; it utilizes the 850, 900, 1800 and 1900 MHz bands. Micro‐PDA, come Elf, è anche UMTS/HSDPA. Bande: UMTS/HSPA+: 800/850/900/1900/2100MHz ‐ GSM/GPRS/EDGE 850 900 1800 1900 MHz for voice and data communication.
The GSM voice capability of this PDA has to be addressed to occasional use, in well covered areas. NOTE If the coverage is poor, the voice quality can be highly affected.
Calls can be made or received using the Lynx as a phone handset, by the Lynx headset or by a Bluetooth® headset. NOTE During a call, you can set the speaker volume by pressing the arrow navigation keys. NOTE In case of heavy usage the Lynx could get warm, this is normal and does not mean a malfunction.
1.7 WIRELESS AND RADIO FREQUENCIES WARNINGS Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications or attachments could damage the product and may violate laws and regulations. WARNING Most modern electronic equipment is shielded from RF signals. However, certain electronic equipment may not be shielded against the RF signals generated by Lynx.
WARNING RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles. Check with the manufacturer or its representative regarding your vehicle. You should also consult the manufacturer of any equipment that has been added to your vehicle. WARNING An air bag inflates with great force. DO NOT place objects, including either installed or portable wireless equipment, in the area over the air bag or in the air bag deployment area.
4. USE AND FUNCTIONING The use of the Lynx depends on the application software loaded. However there are several parameters that can be set and utilities that can be used to perform some basic functions such as data capture, communications, file management, etc 1.1 STARTUP The Lynx turns on when the battery pack or the external supply is inserted and the ON/OFF Power button is pressed. After the battery pack is installed, use the [ON/OFF] key to turn the PDA on and off.
The PDA can also be awakened or turned off by the application program. NOTE 1.1.1 Using the Stylus The stylus selects items and enters information. The stylus functions like a mouse. Tap: Touch the screen once with the stylus to open items and select options. Drag: Hold the stylus on the screen and drag across the screen to select text and images. Drag in a list to select multiple items. Tap-and-hold: Tap and hold the stylus on an item to see a list of actions available for that item.
1.2 WINDOWS EMBEDDED HANDHELD WELCOME WIZARD In Windows Embedded Handheld, at the very first Lynx startup, following a clean boot or following a registry restore to default values, the PDA startup (see par. 1.1) is preceded by the Welcome Wizard. Welcome Wizard Screen The Welcome Wizard allows the user to calibrate the touch screen (see par. 1.6.7) and to configure an email account and a password to protect the terminal.
1.3 DATA CAPTURE To capture data first of all tap Start > Settings > System > Decoding: To configure and enable data capture parameters refer to par. 1.6.1.
1.3.1 Laser Data Capture To scan barcodes, point the Lynx laser model onto the code from a distance within the reading range while pressing the SCAN key. The lighted band emitted by the laser must completely cross the barcode as shown in the figure below. If the scan has taken place correctly: the Good Read LED gets constant Green for a configurable time; if enabled, the GoodReadSound emits an acoustic signal; if enabled, the GreenSpot projects a green spot onto the bar code image.
Remove the protective film cover over the Laser Output Window before use.
1.3.2 Imager Data Capture The Lynx Imager captures a picture of the entire bar code. The omni-directional scanning does not require that the operator orient the bar code to align with the scan pattern. To read a 1D or 2D code, simply point the Lynx Imager model onto the code and press the SCAN Key.
Linear barcode 2D Matrix symbol Ì BX3 ÉÎ Relative Size and Location of Aiming System Pattern The field of view changes its size as you move the reader closer or farther away from the code. The field of view indicated by the aiming system pattern will be smaller when the Lynx Imager is closer to the code and larger when it is farther from the code. Symbologies with smaller bars or elements (mil size) should be read closer to the unit.
1.4 DESCRIPTION OF THE KEYS The Lynx comes with two different keyboards, an alphanumeric keyboard (qwerty), having 46 keys, and a numeric keyboard, having a total of 27 keys. 1.4.
Numeric Keyboard
Main Keys Function KEY FUNCTION It starts barcode data capture. They let you move forwards, backwards, upwards or downwards within text fields, scroll through a Menu list or browse among folder files. Yellow modifier (toggle key): when pressed before a standard key, it enables the character or function printed in yellow above the key. Blue modifier (one shot key): when pressed before a standard key, it enables the character or function printed in blue above the key It powers the Lynx ON or OFF.
1.4.2 Resetting the Lynx There are several reset methods for the Lynx. A warm boot terminates an unresponsive application and clears the working RAM, but preserves the file system. Registry is restored from persistent memory if available or returned to factory default. A cold boot forces all applications to close reinitializing completely the system. It clears the working RAM, but the file system is preserved. Registry is restored from persistent memory.
Clean Boot To perform a clean boot, do the following steps: 1. 2. Perform a Cold Boot (see Cold Boot) Press and hold down the 0 and hang up keys simultaneously and then press the on-off key: + A dialog box will appear asking for confirmation. Press the Enter Key.
1.5 1.5.1 STATUS INDICATORS LED Status The Lynx provides three different LEDs signaling the PDA status. LED STATUS Good Read (right side) Red Charging Status (left side) Keyboard Status (center) Scanning LED is ON from the time the user hits the scan button (Trigger) until the bar code is decoded (laser models) Time-out (imager models). Green Scanning LED is ON, showing a good decode. Green It is constant once the charging process has been completed (full charge).
1.5.2 Taskbar The Taskbar provides information about the time, the battery level, the keyboard function, and the decoding status. Windows Embedded Handheld Taskbar ICONS DESCRIPTION Zooms the screen. Opens the Wireless Manager (see par. 1.6.6). Displays the system battery status. Allows to set the volume of screen taps. Opens Clock & Alarms application. It allows to set date, time and alarms.
1.6 CONTROL PANEL From the Start menu, tap Settings. The Control Panel is split into three sections: Personal, System, Connections.
1.6.1 Data Capture Configuration You can configure the Lynx’s decoding options by tapping Start -> Settings -> System -> Decoding: There are two sections in the Decoding control panel, each containing additional pages. There are seven General Configuration pages and multiple Barcode symbology pages. DECODING CONFIGURATION PAGES Select the desired configuration from the options shown in the figure below, and the other Decoding Properties figures on the following pages.
Audio From the Decoding menu, tap Configure > General > Audio. Use it to set volume, tone, duration, and number of various types of beeps. Good Read From the Decoding Properties page, tap Configure > General > Good Read. Use it to enable Good Read indications, the use of Green Spot and a to set the decoding timeout for decoding labels.
Formatting From the Decoding Properties page, tap Configure > General > Formatting. Use it to configure prefix, suffix and data separator character strings. General Options From the Decoding menu, tap Configure > General > General Options. Select from Label Programming Enable, Symbology IDs and Group Separator Replacement.
Decoding Options From the Decoding Properties page, tap Configure > General > Decoding Options. Use it to configure the User ID for symbologies, Redundancy and Aggressive Decoding (if supported by the decoding module). Select a symbology to view or change the available properties settings.
Spot Beam From the Decoding Properties page, tap Configure > General > Spot Beam. It allows enabling and configuration of Spot Beam and triggering modes. It is only available on devices equipped with laser and advanced long range laser decoding modules that support the Spot Beam Feature.
Imager Options From the Decoding Properties page, tap Configure > General > Imager Options. It configures illumination, target beam and Pick List mode, and triggering modes. It is only available on devices equipped with 2D decoding engines.
Devices From the Decoding Properties page, tap Configure > General > Devices. Use it to enable or disable the keyboard wedge for Barcode scanner.
1D Barcode Symbology Pages Use the drop-down menus from Configure > 1D Barcode, or tap the left and right arrow keys to navigate the different pages of the barcode symbology pages. Each barcode symbology opens to its own page, as shown in the figure below. Refer to the sample symbology control panels for examples of the types of fields and options you can modify. Codabar: Select Enable, Min/Max Lengths, Enable Checksum, Send Checksum, Send Start/Stop, Convert to CLSI and Wide Gaps.
Decoding Settings Select from the Decoding Properties Settings menu to restore configurations and/or other available default settings. Choose from: Factory Defaults Minimum Settings Maximum Settings Save (New Settings) Revert to Saved Settings previous The settings are saved when you tap OK. The settings are saved when you tap ‘Yes’. When open, Decoding Properties acts as a simple barcode test tool that provides the Data decoded and the Data Type of the barcode scanned.
1.6.2 Buttons From the Start menu, tap Settings > Personal > Buttons. On the Program Buttons tab, customize the program hardware buttons to launch your most used applications. Under ‘Select a button’, tap the button you want to assign a program to, and then select a program from ‘Assign a program’. To configure the way the up/down control repeats, use the Up/Down Control applet (Start > Settings > Personal > Buttons > Up/Down Control).
1.6.3 DL Buttons In Windows Embedded Handheld devices, - buttons (excluding F5) are assigned by Windows to default applications. To customize one of these buttons and assign it to a different application, you first need to disable it. Tap Start > Settings > System > DL Buttons to display the DL Buttons window: Select the button you want to disable. Select the function ‘None’ and the click OK. To remove the disabled button, select it and click ‘Delete’.
A dialogue box appears, asking for confirmation.
To assign a new application to the button, select the function and then click ‘OK’: To restore the old settings , do a clean boot.
1.6.4 Triggers Triggers are special customizable buttons that are mapped by default by DL Mobile.
1.6.5 Application Switcher The application switcher provides the same functionality as the standard Windows® Alt+Tab function. This allows the user to switch between the various open applications. The application switcher is activated via an assigned shortcut key specified in the “DL Buttons” tab (refer to par. 1.6.3). When the assigned button is pressed, the dialog shown below will be displayed: The key can be used to close the Application Switcher.
1.6.6 Wireless Communications The Wireless Manager application is a sort of 'Control Panel' for wireless connections. From here it's possible to turn on or off bluetooth® and radio modules. Open the Wireless Manager by tapping Start > Settings > Connections > Wireless Manager, or by tapping the connectivity icon on the taskbar (see par. 오류! 참조 원본을 찾을 수 없습니다.).
Summit Client Utility (SCU) Wireless networking has a customized control, Summit Client Utility (SCU), specific to the radio.
1. To create a new profile, tap the "Profile" tab: Information about the wireless network can be entered directly in the profile tab or by pressing “Scan” when the desired network ESSID is in range. 2.
3. Click the "Configure" button 4. Follow the on-screen instructions to setup security parameters for your network. For more detailed settings specific to your installation please contact your wireless network administrator. 5. When finished, click “Commit” to save your settings. Return to the “Main” tab, if you have not previously selected “Commit” you will be prompted to save your changes.
At the “Main” tab select the profile you just created. If you used the “scan” button the desired profile will have the same name as the ESSID. Use the “Status” tab to check connectivity to the network. More detailed information about the applet for radio configuration can be found at http://www.summitdata.com/SCU.htm.
1.6.7 Stylus Calibration You might need to recalibrate the touch screen (i.e. when you attempt to select one item with the stylus, another item is erroneously selected). To recalibrate the touch screen, complete the following steps: 1. Select Start > Settings > System > Screen to open the Screen Settings dialog as shown in the figure below: 2. 3. Tap Align Screen to open the Calibration screen shown in the figure below. Carefully press and briefly hold stylus on the center of the target.
Startup Stylus Calibration When starting the terminal, a Welcome Wizard (with Stylus Calibration) comes up if valid calibration settings are not available. This happens in the following circumstances: 1. 2. 3. At the first startup of the terminal. After any cold boot if the user skipped stylus calibration earlier. After a Clean Boot.
1.6.8 Audio Settings There are two applets that control volume: Audio and Volume & Sounds. Audio From the Start Menu, tap Settings > System > Audio: The audio control panel can be used to independently set the playback or recording volume for different types of audio inputs and outputs, such as a headset, powered mobile dock, or the internal speakers and microphone.
Sounds & Notifications From the Start Menu, tap Settings > Sounds and Notifications: The Volume & Sounds applet configures audio features of all speakers and headphones: Sounds Tab Notifications Tab
To set the Bluetooth® headset volume, you can also tap: Start > Settings > System > Bluetooth Manager > Connections and select the headset.
1.7 WINDOWS CONNECTIONS To connect the Lynx to another device (i.e. Host PC) from Windows, several programs are available. These programs require specific electrical connections in order to function properly. 1.7.1 Windows Mobile® Device Center The desktop application Windows Mobile® Device Center gives you the ability to synchronize information between a desktop computer and your Lynx.
Visit the following Microsoft Web site for the latest in updates and technical information: NOTE NOTE http://www.microsoft.com/windowsphone/enus/howto/wp6/sync/prepare-to-sync-windows-phone-6-5-with-mycomputer.aspx When a microSD card is inserted, Lynx allows a mass storage data connection to a host PC. This functionality can be enabled through the Control Panel. When doing so, the microSD card is not available to the Lynx. An ActiveSync connection is not possible when this feature is enabled.
1.7.2 Bluetooth®, Manager Device Setup The Bluetooth® Manager icon will only be visible if Bluetooth® hardware has been installed on the unit. NOTE Using the Lynx to connect to another device To create a Bluetooth® pairing between your device and another device that has Bluetooth® capabilities, ensure that the two devices are turned on, discoverable, and within close range. 1. Open the Bluetooth® control panel by tapping Start > Settings > System > Bluetooth Manager: 2.
3. Once searching is complete, Bluetooth® device Profiles will be displayed in the Discovery tab. You can set up a connection to a device in the list by selecting the device and then tapping the 'Connect' button: To create a pairing: 1. Select a service: 2. Configure any encryption, authentication, or virtual port options required by the service selected.
Icon Service Dialup Networking Printer Object Push (OPP) Object Exchange (OBEX) ActiveSync Human Interface Device (HID) - Keyboard Serial Personal Area Network (PAN) Modem Headset Handsfree Virtual Port allows you to specify the incoming port, which is used to communicate serially with an incoming device just as if it were a physical COM port. This option is available only if you have selected a Printer or Serial service.
You can also select Encrypt or Authenticate from the Bluetooth® control panel to apply or modify those settings. 1. To require Authentication, check the checkbox, then tap OK. 2. If required, the Authentication Request dialog will then open, requesting that you enter a PIN. Use the Input Panel or the keyboard to type the PIN. 3. Tap OK to complete.
The dialog will also appear when an Authentication request is received from another device. Once you have set up a Pairing, you can view the settings by double-tapping its name from the Connections tab. Tap the arrow to change the Virtual Port, or Delete to remove the device pairing. Tap Sync to initiate a Sync (available only if the service is an ActiveSync connection).
Using your device to connect to the Lynx Before turning on Bluetooth®, ensure that the two devices are within close range and that both Bluetooth-enabled devices are discoverable. 1. Tap Start > Settings > System > Bluetooth Manager to open the Bluetooth® control panel. 2. Tap Settings. The Settings tab allows you to enable or disable the Bluetooth® radio and specify settings for Incoming Connections.
3. Select or clear the “Enable Bluetooth Radio” check box. If you’re going to be attaching a serial device (i.e. a scanner) to the Lynx, use the Port control to select a virtual COM port to use for the connection. 4. Tap ‘Find Me’ if you want to make the Lynx visible to other Bluetooth® devices for 60 seconds, allowing them to set up a connection.
By default, Bluetooth® is turned off. If you turn it on, and then turn off your device, Bluetooth® also turns off. When you turn on your device again, Bluetooth® turns on automatically.
1.7.3 Windows Mobile Phone For information on Windows Mobile Phone use and functioning, refer to the Windows Mobile web site: http://www.microsoft.com/windowsmobile.
1.8 SKYHOOK° XPS SETTINGS 1.8.1 XPS - Virtual GPS for Windows Mobile Skyhook synthesizes data from Skyhook's Wi-Fi Positioning System (WPS), GPS satellites and cell towers with advanced hybrid positioning algorithms combining as much as possible to build a composite position and to provide the best possible location available in any environment. XPS Program Icon 1.8.
Storage – tab Temporary folder: Select the folder on your device or storage card where the XPS application will store data files. Temporary folder max size: This controls the amount data storage allocated to the XPS Settings application (default setting is 4096kb). Port – tab XPS Port: Select the port that XPS will stream location data from by default, XPS will select an unused port. Disabling other serial drivers: Use this option to disable an active device if a port for XPS is needed.
Service – tab Activate / Deactivate: Toggles the XPS service On and Off. About – tab About: View the XPS version and copyright information. 1.8.3 Uninstalling XPS To remove XPS from your Windows Mobile device: 1. Open the Settings panel 2. Open the System panel 3. Tap ‘Remove Programs’ 4.
1.8.4 FAQ and Troubleshooting 1. Can I install to a storage card? Yes – however, as with most mobile apps installing to the device is recommended. 2. What does registering XPS as my default GPS do? Registering XPS simply sets the Windows Mobile OS to use XPS whenever an application asks for positioning. If you choose not to set XPS as the default, you will need to select the XPS COM port manually when configuring an application. 3.
1.9 DATALOGIC FIRMWARE UTILITY The Datalogic devices are equipped with a field upgradeable firmware mechanism. Firmware updates are available on the Datalogic ADC website (http://www.adc.datalogic.com/). After you have downloaded the desired update, there are several ways you can update the firmware on your device. Use Wavelink Avalanche™ if you have multiple Datalogic ADC devices to update. Refer to the Product CD included with your device for more information.
1.9.2 Installing DFU on the Host PC The Datalogic Firmware Utility (DFU) provides administrators with a field upgrade mechanism. You must have Microsoft® ActiveSync (for Windows XP devices) or Windows Mobile® Device Center (for Windows 7 and Vista devices) already loaded and running on the host PC to use DFU. Refer to par. 1.7.1 for more information about Windows Mobile® Device Center. Prior to installing, you must remove any previous versions of DFU installed on the host PC.
1.9.3 Updating the Firmware After copying the firmware image to the host PC (see par. 4.10.1) and installing DFU (see par. 1.9.2), you can upgrade the firmware on your Datalogic device. The following steps require that you have already established an ActiveSync or Windows Mobile® Device Center connection between the host computer and the Datalogic device. NOTE 1. Go to Start > Programs > DFU > Datalogic Firmware Utility. 2. Verify that ActiveSync is selected by clicking Communications > ActiveSync.
1.10 DATALOGIC CONFIGURATION UTILITY Datalogic Configuration Utility (DCU) is a Datalogic Windows-based utility tool allowing the uploading, modifying and downloading of a Datalogic device. Configuration settings include Scanner, Control Panel, and Datalogic Desktop Utility (DDU). The DCU installer is available on the product CD which came with your device or from the Datalogic ADC web page (http://www.adc.datalogic.
1.11 SUSPEND MANAGEMENT Suspend Management allows the user to keep device features powered while the device is off. The features managed by this feature are: Cellular Data/Voice and GPS. NOTE The WiFi driver has been measured to consume about 50 µA when left powered. As a result, WiFi will always be left powered during suspend. This has the positive effect of substantially reducing the time required for WiFi to fully resume when the device is powered back on.
The user is given five seconds to respond. If the user selects "Yes", then the device and all features are powered off. If the user selects "No", or does not respond within five seconds, the device will power off, but leave features as they were. The term "device off" here refers to a condition where the display is off and the device appears unpowered. The device CPU may in fact be powered on. In this condition the power consumption can be relevant and battery can be completely discharged in some hours.
1.12 DATALOGIC DESKTOP UTILITY Datalogic Desktop Utility (DDU) allows Datalogic Windows administrators to configure Windows CE and Embedded Handheld devices to control individual user access. This includes: • • • • Prevent users from changing your device OS settings. Use Application Selector to replace desktop with a selection of authorized applications. Internet Explorer access restriction, configuration and customized error recovery mechanisms. Create quick access hot keys and configure trigger actions.
1.12.1 Administrative Options (Admin tab) When you open the DDU control panel, the “Admin” tab appears. COMMAND DESCRIPTION Enable Datalogic Desktop Select/tap this checkbox to activate the DDU functions such as Windows Access Restrictions and Application Selector. Enter Password Enter a password in the text box. This allows the user to specify a password when this utility is launched. By default the password is “1234”. A password can consist of all standard keyboard characters.
Setting a Password To set a password: 1. Enter a password in the field. This allows the user to specify a password when this utility is launched. By default the password is “1234”. Be sure to record the Password for future reference. NOTE 2. 3. 4. Re-enter the password in the second field. Select/tap “Set Password” to enable the password. Select/tap “OK” to close the “Set Password Confirmation” dialog.
Removing a Password To remove a password: 1. 2. Enter blanks in both “Password” fields. Select/tap “Set Password”. Password Request Dialog Box Once the password is set, the next time you open the “Datalogic Desktop Utility”, the DDU Password dialog box opens. This dialog box will only open if a password was defined. 1. 2. Type in your password using either the keypad on the unit, or using the stylus on the soft input panel (SIP).
1.12.2 WebAppLock Options (WebAppLoc tab) Tap the "WebAppLocK” tab to access the WebAppLock Configuration options. Error Page Redirection Use the Error Redirection option to provide customized recovery from common errors. When an error occurs, the browser can redirect access to a specified error page with instructions on how to recover from the problem.
Other options Full Screen Set the web browser in full screen mode. Status Icon Enable or disable the status icons view (see par. 1.12.3). Trap Keys When checked, all key presses will be trapped by WebAppLock to prevent the user from accessing other parts of the system. DL Buttons keys will not work in WebAppLock when this box is checked. When unchecked, all system key presses, including DL Buttons keys, will work.
1.12.3 Status Icons Options (Status Tab) Tap the “Status” tab to access the Status Icons option. You can configure the view of some status icons that are used in “WebAppLock” and in “Application Selector” to display the status of: wi-fi radio, battery and GSM. Status Icons Options Set Status Icon Defaults Restores the status icons’ factory settings. Icon Size Sets the status icons’ size. Icon Location Selects the preferred location for each status icon.
1.12.4 Windows Controls Select/tap the “Win” (Windows Controls) tab to access the Windows Controls option. Use Windows controls to allow or restrict access to Windows system functions. You can disable normal Windows functions such as the taskbar, leaving nothing but a blank workspace. This allows applications to be run on the full screen and prevents users from accidental or unauthorized use of the taskbar, Internet Explorer, and any other resident applications.
WINDOWS CONTROLS Taskbar Enabled Select/tap “Taskbar Enabled” to specify whether the taskbar is accessible. This option is only available when the “Show Taskbar” is checked. AutoSIP Enabled Enables the AutoSIP Windows feature. Scroll Bars Enabled This control only take effects in WebAppLock. When checked, displays horizontal and vertical scroll bars to help view large web pages which do not fit the screen. When unckecked, those scrolls will not be present.
1.12.5 AppSelector Options (AppSelect tab) Tap the Application Selector (“AppSelect” Tab) to edit, add, or delete applications for the application selector. Application Selector Options Enable Application Selector Select/tap “Enable Application Selector” to enable/disable the application selector. When this is enabled, the Application Selector replaces the desktop and allows only authorized use of applications. Authorized Applications This is a list of applications that the user may access.
Add Applications The “Add Application” dialog opens when you tap either “New” or “Edit”. From the “Add Application” dialog the administrator can configure and/or add/change an a new application entry in the list. Applications with the “Run Application at Startup” option enabled will start automatically when the Application Selector starts up. COMMAND DESCRIPTION Application Title Type the name of the application in this textbox in the way you wish it to appear for the user.
COMMAND DESCRIPTION Browse to browse for the desired icon file. The Select/tap results of this search are placed in the “Icon File” textbox. Run Application at Startup Select/tap this box to force this application to auto start when the Application Selector starts up. Applications will be started in the order listed in the authorized application list. Delay Enter a delay duration in seconds in the combo box.
1.13 APPSELECTOR (APPLICATION SELECTOR) The Application Selector is an application that allows a device to run in kiosk mode. The administrator can choose for the user to have access to the desktop or not. The Application Selector can replace the desktop and limit the user to the specified list of applications. By default, the Application Selector comes with the WebAppLock preset. The administrator can customize this list as shown in chapter 1.12.5. To run an application, tap on its name.
1.14 WEBAPPLOCK (LOCKED WEB BROWSER) WebAppLock is a web browser that creates a restricted internet usage environment. It prevents the user from exiting the web application/ website set by the administrator. Zoom In and Zoom Out will only affect screen text and not bitmaps. NOTE If the taskbar has been disabled, the Settings menu is not displayed.
For firmware versions 1.60 and greater, the following command line arguments are supported: - /E optional parameter which allows for Exit without entering a password - @URL optional parameter which specifies a URL to use as a home page. - /C optional parameter which disables the ctrl keys (including the one to exit). - /W optional parameter which allows for a performance boost. When present, only WIFI error redirection will function.
1.14.1 WebApplock Special Meta-tags General Meta-Tag Comments A meta-tag is a special HTML tag that is used to store information about a Web page but is not displayed in a Web browser. For example, meta tags provide information such as what program was used to create the page, a description of the page, and keywords that are relevant to the page. As per the HTML specification, all meta-tags must be contained within a
… tag set.CGI Error Meta-tag DL_CGIError – Overrides DDU error page redirection and replaces it with a reference to a CGI script which is passed the error number as an argument. Content – A CGI URL with variable name argument in place. The name of both the CGI function and the error number variable is completely configurable by the user. Do not put an ‘=’ at end of the URL. HTTP header error numbers are returned if they are greater than or equal to 300.
GetSerialNumber Meta-tag DL_GetSerialNumber – Obtains the device serial number and sends it as an argument to a customer’s javascript function. Content – name of function to pass serial number to. Example: When this page is loaded the specified javascript function with the device number as the only argument (such as CustomerFunction(‘D10P00031’).
Decoding meta-tags: Each decoding meta-tag has a possible content of “Enable” or “Disable”. The settings are valid for the entire page (enable/disable each symbology).
Key press Metatags The key press meta-tags can be used to call JavaScript functions. They have the name structure: “DL_Key_xxx” where xxx is the VKey code. Example: If one of this tag is present, the pressure of this key is handled at level of page, independently from the currently focused item. Refer to the Microsoft website to find the list of all the possible Vkey codes: http://msdn.microsoft.com/en-us/library/bb431750.aspx http://msdn.
1.15 AUTOSTART The AutoStart program provides three functions: Allows you to create a list of applications (with optional command line arguments) to run automatically prior to loading CAB files. - Automatically reinstalls specified CAB files when the Lynx 10 is cold booted. - Allows you to create a list of applications (with optional command line arguments) to run automatically after loading CAB files.
1.15.2 How AutoStart Uses Wceload If you intend to create highly interactive installers, you should either install the CABs manually or review the section on “Interactive CAB Install” in this chapter.. NOTE In certain environments, CAB files will be deleted after execution. To prevent the CAB file from being deleted, write protect the file before copying the file onto the device. CAUTION CAB files are installed by AutoStart using the Wceload.exe application.
1.15.3 Interactive CAB Install If the CAB installer requires user interaction that must be performed during the AutoStart CAB installation process, you can specify a special file name to disable the silent mode installation. If this mode is specified, the CAB file will be installed with Wceload without any command line arguments specified. An example of what AutoStart would execute is: \Windows\Wceload.
The following table breaks down the sample Autostart.ini line: Autostart option(s) - Full path to executable \windows\pword.exe Command line arguments \file.doc Spaces must be placed between each component of the line in the Autostart.ini. If the executable path is in a folder that contains spaces in the name, quotes are required to distinguish what the actual executable name is. The following is an example of this: “\Program Files\ScannerApp.exe” /run (valid) \Program Files\ScannerApp.
AutoStart Options The table below shows options you can use when writing a line in the Autostart.ini file. Description Character Comment: This line will not be ‘#’ OR ‘ ‘ (space) executed. Comments This may only be used as the first character of the line. If the comment option is specified in the options elsewhere, it is ignored. Do not wait on line completion: This will cause the line to ‘-’ execute and immediately move onto the next line.
Combining Options Autostart options can be combined together as shown in the following sample: ?- \Windows\Pword.exe This line would: Request confirmation before executing the line. The next line would not be processed before the confirmation is answered. Run the next line without waiting on the current line to complete execution. Query Option The query option is intended for use when debugging the autostart.ini.
The fields may be broken up into multiple lines (as shown in the example) due to limited space in the dialog. NOTE AutoStart Query Options Parentheses are used to surround the given field and make it very clear what the value of the field is. The following table describes the results of each choice: Button Action Yes The current line will execute. No The current line will not execute. AutoStart will continue parsing the Autostart.ini.
Autostart.ini Samples The next table is a collection of sample Autostart.ini lines: Line Description This will confirm the execution of ? \windows\wceload.exe “\My \Windows\wceload.exe with specified argument Documents\Sample.cab” “\My Documents\Sample.cab” \Program Files\App.exe (invalid) This will execute \Program with the argument Files\App.exe. \Program Files\App.exe /run (invalid) This will execute \Program with the argument Files\App.exe /run. “\Program Files\App.
5. TECHNICAL FEATURES 1.1 TECHNICAL DATA PHYSICAL CHARACTERISTICS DIMENSIONS (LXWXH) 157 x 81x 42 mm (6.18 x 3.18 x 1.65 in) WEIGHT (DEPENDING ON MODEL) 415 to 440 g (14.6 to 15.5 oz) depending on model (incl. battery) AUDIO Loudspeaker Headset LEDS Six LEDs Decoding Status/ Keyboard Status/ Charging Status DISPLAY Reflective TFT daylight readable color display, allowing both resolution 320 x 240 pixels and 640 x 480, 89 mm (3.
SYSTEM OPERATING SYSTEM Microsoft Windows Mobile 6.5 with Office Mobile 2010: Outlook, Word Mobile, Excel Mobile, PowerPoint Mobile, One Note Mobile and Internet Explorer Mobile 6.0 MICROPROCESSOR XScale™ PXA310 @ 624 MHz SYSTEM RAM MEMORY 256 MB SYSTEM FLASH MEMORY 256 MB (including backup directory for user data & program permanent storage) POWER SUPPLY* Removable battery pack with rechargeable Li-ion batteries; 3.7 V 3000/5000 mAh (11.10/18.
READING OPTIONS LASER CHARACTERISTICS SCANNING RATE 104 ± 12 scan/sec MINIMUM RESOLUTION 0.
1.
LYNX SE4500-DL Typical Reading Diagram - Reading Zones (10° skew angle) 13 mil UPC-A 6.67 mil PDF417 200 10 mil PDF417 5.0 mil PDF417 150 5.0 mil Code 39 20 mil Code 39 15 mil PDF417 7.
6. TEST CODES High Density Codes 0.25 mm (10 mils) Code 39 !17162H! 17162 2/5 Interleaved Ë"8NduÌ 0123456784 Code 128 ÌtestwÎ test 80% EAN 13 x(0B2DE5*KKKKLM( 80% EAN 8 (6450*TRMN( Medium Density Codes 0.
Interleaved 2/5 Ë"8NduÌ 0123456784 Code 128 ÌtestwÎ test 100% EAN 13 x(0B2DE5*KKKKLM( 100% EAN 8 (6450*TRMN( Low Density Codes 0.
Code 128 ÌtestwÎ test 120% EAN 13 x(0B2DE5*KKKKLM( 120% EAN 8 (6450*TRMN(
2D Codes Datamatrix ECC200 Example Inverse Datamatrix ECC200 Example
DECODING PARAMETERS This section contains information about programmable settings for the Lynx™. Use the Lynx™ Management Utility (FMU), the Scanner Control Panel applet, the Imaging Control Panel applets to program the Lynx™. It provides the following information: Code Parameter is the “human” name for the programming option. I.D. # is the “decoder” name for the programming option. For example, to set a Code 39 minimum label length, use I.D. 0120. Programming I.D.
PROGRAMMING CODES WITHOUT PARAMETERS The following table describes the functions of special bar codes that take no parameters: Code Parameter I.D. # Function Defaults Minimum FF39 Turns every On/Off parameter off and sets all minimum and Maximum Label Lengths to the lowest values. Defaults Maximum FF3A Turns every On/Off parameter on and sets all minimum and Maximum Label Lengths to the highest values. This default set is normally used only for troubleshooting.
BAR CODE PARAMETERS The following table lists the standard customer programmable settings for the Lynx™: Codabar 2D Imager Lorax Accept. Input √ √ √ √ √ Laser I.D.# Scanner Type Factory Description Max Code Parameter Min Defaults Enter 1 for On and 0 for Off Enable Enables/disables the Codabar symbology.
Code Parameter Description I.D.# Accept. Input Max Factory Laser 2D Imager Lorax Scanner Type Min Defaults Maximum Label Length This feature specifies the maximum allowable length of a Codabar label. The length includes check and data characters. Maximum Label Length should be greater than or equal to Minimum Label Length. 0321 01 - 50 01 50 20 √ √ √ Read Verification Sets the number of times a label must be read before it is transmitted.
Code 39 2D Imager Lorax Accept. Input √ √ √ √ √ Laser Enable Enables/disables the Code 39 symbology. I.D.# Scanner Type Factory Description Max Code Parameter Min Defaults Enter 1 for On and 0 for Off 0100 On or Off Off On On √ 0101 On or Off Off On Off √ 0102 On or Off Off Off Off Enable Checksum Enables more aggressive decoding algorithms to be used in order to scan hard to read labels. Requires the use of checksum characters to verify a bar code.
Pharmacode 39 (Code 32) Lorax Off On Off √ √ √ 0112 On or Off Off Off Off √ √ √ 0113 On or Off Off On Off √ √ √ 0127 Any single ASCII character (00 = Off) ‘Y’ ‘Y’ ‘Y’ √ √ √ Laser On or Off Accept. Input Factory 0110 I.D.# Max Description Min Code Parameter Scanner Type 2D Imager Defaults Enter 1 for On and 0 for Off Enable Send Checksum Enables/ disables the Pharmacode 39 (Code 32) symbology.
Trioptic Enter 1 for On and 0 for Off Enables/disables the Trioptic symbology. 0108 On or Off Off On Off √ Enable Aggressive Decoding Enables more aggressive decoding algorithms to be used in order to scan hard to read labels. 0109 On or Off Off On Off √ Read Verification Sets the number of times a label must be read before it is transmitted.
Code 93 2D Imager Lorax Accept. Input √ √ √ √ √ 20 √ √ √ 02 01 √ √ ‘L’ ‘L’ √ √ Laser Enable Enables/disables the Code 93 symbology. I.D.# Scanner Type Factory Description Max Code Parameter Min Defaults Enter 1 for On and 0 for Off 0400 On or Off Off On Off √ 0401 On or Off Off On Off √ 0420 01 - 50 01 01 02 Maximum Label Length This feature specifies the maximum allowable length of a Code 93 label. The length includes check and data characters.
Code 128 2D Imager Lorax Accept. Input √ √ √ √ √ √ √ 20 √ √ √ 01 √ √ Laser Enable Enables/disables the Code 128 symbology. I.D.# Scanner Type Factory Description Max Code Parameter Min Defaults Enter 1 for On and 0 for Off 0408 On or Off Off On On √ 0409 On or Off Off On Off √ 040C On or Off Off On Off √ Code 128 Ext. ASCII Enable Enable Extended ASCII character conversion.
Lorax 0427 Any single ASCII character (00 = Off) 2D Imager Accept. Input Laser User ID Specifies the symbology identifier (if any) that is sent when parameter Send Code ID (Index 0025) is set to 3. ASCII code zero (null) is used to indicate that an identifier is not to be sent for the symbology. I.D.
European Article Numbering-13 (EAN-13) On or Off Off On On √ √ √ Enable Aggressive Decoding Enables more aggressive decoding algorithms to be used in order to scan hard to read labels. 0511 On or Off Off On Off √ √ Send Check Digit Includes a check digit in the label which is transmitted. 0512 On or Off Off On Off √ √ √ Send System Digit This instructs the decoder to include the system digit in the label transmission. For UPC-E, the system digit is zero.
Lorax 0525 Any single ASCII character (00 = Off) 2D Imager Accept. Input Laser Specifies the symbology identifier (if any) that is sent by the decoder when parameter Send Code ID (Index 0025) is set to 3. ASCII code zero (null) is used to indicate that an identifier is not to be sent for the symbology. I.D.
European Article Numbering-8 (EAN-8) Lorax Off On On √ √ √ 0519 On or Off Off On Off √ √ 051A On or Off Off On Off √ √ √ √ √ √ √ Laser On or Off Accept. Input Factory 0518 I.D.# Max Description Min Code Parameter Scanner Type 2D Imager Defaults Enter 1 for On and 0 for Off Enable Enable Aggressive Decoding Send Check Digit Enables/disables the EAN8 symbology. Enables more aggressive decoding algorithms to be used in order to scan hard to read labels.
Universal Product Code-A (UPC-A) Lorax Off On On √ √ √ 0501 On or Off Off On Off √ √ Laser On or Off Accept. Input Factory 0500 I.D.# Max Description Min Code Parameter Scanner Type 2D Imager Defaults Enter 1 for On and 0 for Off Enable Aggressive Decoding Enables/disables the UPCA symbology. Enables more aggressive decoding algorithms to be used in order to scan hard to read labels. Send Check Digit Includes check digit in the label which is transmitted.
Universal Product Code-E (UPC-E) On or Off Off On On √ √ √ Enable Aggressive Decoding Enables more aggressive decoding algorithms to be used in order to scan hard to read labels. 0509 On or Off Off On Off √ √ Send Check Digit Includes the check digit in the label which is transmitted. 050A On or Off Off On Off √ √ √ Send System Digit This instructs the decoder to include the system digit in the label transmission. For UPC-E, the system digit is zero.
UPC / EAN Extensions Lorax On or Off Off On On √ √ √ 051D On or Off Off On Off √ √ √ 051E On or Off Off On Off Laser 051C Accept. Input Factory Enable 2Digit Extensions Requires a 2 digit extension (supplemental label) to be verified for a successful decode of a label. Requires a 5 digit extension (supplemental label) to be verified for a successful decode of a label. Enables/disables Code 128 extensions. I.D.
Interleaved 2 of 5 Lorax √ √ √ √ Off √ √ √ Off Off √ √ √ 02 02 06 √ √ √ 02 - 50 02 50 10 √ √ √ 01 - 04 01 02 01 √ √ Laser √ Accept. Input Factory I.D.# Max Description Min Code Parameter Scanner Type 2D Imager Defaults Enter 1 for On and 0 for Off Enables/ disables the Interleaved 2 of 5 symbology. Enables more aggressive decoding algorithms to be used in order to scan hard to read labels. Requires the use of checksum characters to verify a bar code.
Lorax 022B Any single ASCII character (00 = Off) 2D Imager Accept. Input Laser Specifies the symbology identifier (if any) that is sent by the decoder when parameter Send Code ID (Index 0025) is set to 3. ASCII code zero (null) is used to indicate that an identifier is not to be sent for the symbology. I.D.
Standard 2 of 5 2D Imager Lorax Accept. Input Laser I.D.# Scanner Type Factory Description Max Code Parameter Min Defaults √ √ Enter 1 for On and 0 for Off Enable Enable Aggressive Decoding Enable Checksum Enables/disables the Standard 2 of 5 symbology. Enables more aggressive decoding algorithms to be used in order to scan hard to read labels. Requires the use of checksum characters to verify a bar code.
Matrix 2 of 5 Enter 1 for On and 0 for Off Enable Enable Aggressive Decoding Enable Checksum Enables/ disables the Matrix 2 of 5 symbology. Enables more aggressive decoding algorithms to be used in order to scan hard to read labels. Requires the use of checksum characters to verify a bar code. 0208 On or Off Off On Off √ √ 0209 On or Off Off On Off √ 020A On or Off Off Off Off √ √ Send Checksum Instructs the terminal to include the checksum in the label transmission.
MSI 2D Imager Lorax Accept. Input Laser I.D.# Scanner Type Factory Description Max Code Parameter Min Defaults √ √ Enter 1 for On and 0 for Off Enable Enable Aggressive Decoding Enables/ disables the MSI symbology. Enables more aggressive decoding algorithms to be used in order to scan hard to read labels. 0608 On or Off Off On Off √ 0609 On or Off Off On Off √ Require 2 Check Digits An MSCI label must contain 2 check digits.
GS1 DataBar-14 Lorax 2D Imager Accept. Input Laser I.D.# Scanner Type Factory Description Max Code Parameter Min Defaults Enter 1 for On and 0 for Off Enable Convert to UCC-EAN 128 NOTE Enables/ disables the GS1 0800 On or Off Off On On √ √ √ DataBar -14 symbology. Instructs the decoder to transmit the label data as one or more UCC-128 0804 On or Off Off On Off √ √ √ labels. The transmission will use the UCC-128 AIM identifier.
GS1 DataBar Limited Lorax 2D Imager Accept. Input Laser I.D.# Scanner Type Factory Description Max Code Parameter Min Defaults Enter 1 for On and 0 for Off Enable Convert to UCC-EAN 128 NOTE Enables/disables the GS1 0808 On or Off Off On On √ √ √ DataBar Limited symbology. Instructs the decoder to transmit the label data as one or more UCC-128 080C On or Off Off On Off √ √ √ labels. The transmission will use the UCC-128 AIM identifier.
GS1 DataBar Expanded Lorax Off On On √ √ √ 0814 On or Off Off On Off √ √ √ Laser On or Off Accept. Input Factory 0810 I.D.# Max Description Min Code Parameter Scanner Type 2D Imager Defaults Enter 1 for On and 0 for Off Enable Convert to UCC-EAN 128 Enables/disables the GS1 DataBar Expanded symbology. Instructs the decoder to transmit the label data as one or more UCC-128 labels. The transmission will use the UCC-128 AIM identifier.
PROGRAMMABLE 2D SYMBOLOGIES Aztec Code Accept. Input Factory I.D.# Max Description Min Code Parameter 2D Imager Scanner Type Defaults Enter 1 for On and 0 for Off Aztec Code Enable Enables/disables the Aztec symbology. 0B18 On or Off Off On On √ Aztec Code Minimum Set the minimum bar code label length to be less than or equal to maximum label length. 0B2C 1-3750 1 3750 1 √ Aztec Code Maximum This feature specifies the maximum allowable length of a label.
DataMatrix Accept. Input Factory I.D.# Max Description Min Code Parameter 2D Imager Scanner Type Defaults Enter 1 for On and 0 for Off Datamatrix Enable Enables/ disables the Datamatrix symbology. 0B00 On or Off Off On On √ Datamatrix Minimum Set the minimum bar code label length to be less than or equal to maximum label length. 0B20 1-1500 1 1500 1 √ Datamatrix Maximum This feature specifies the maximum allowable length of a label.
Composite Accept. Input Factory I.D.# Max Description Min Code Parameter 2D Imager Scanner Type Defaults Enter 1 for On and 0 for Off Enables/disables the Composite symbology. 0A10 On or Off Off On Off √ Composite to UCC/EAN-128 Instructs the decoder to transmit the label data as one or more UCC-128 labels. The transmission will use the UCC-128 AIM identifier.
Maxicode 2D Imager Scanner Type Defaults Enables/ disables the Maxicode symbology. 0B08 On or Off Off On On √ Minimum Label Length Set the minimum bar code label length to be less than or equal to maximum label length. 0B24 1-138 1 138 1 √ Maxicode Maximum This feature specifies the maximum allowable length of a label. The length includes check and data characters, if applicable. Maximum Label Length should be greater than or equal to Minimum Label Length.
PDF 417 2D Imager Scanner Type Defaults Enables/disables the PDF 417 symbology. 0A00 On or Off Off On On √ PDF-417 Minimum Set the minimum bar code label length to be less than or equal to maximum label length. 0A20 1 - 2710 1 2710 1 √ PDF-417 Maximum This feature specifies the maximum allowable length of a label. The length includes check and data characters, if applicable. Maximum Label Length should be greater than or equal to Minimum Label Length.
MicroPDF 417 2D Imager Scanner Type Defaults Enables/disables the MicroPDF 417 symbology. 0A08 On or Off Off On Off √ MicroPDF-417 Minimum Set the minimum bar code label length to be less than or equal to maximum label length. 0A24 1 - 366 1 366 1 √ MicroPDF-417 Maximum This feature specifies the maximum allowable length of a label. The length includes check and data characters, if applicable. Maximum Label Length should be greater than or equal to Minimum Label Length.
QR Code 2D Imager Scanner Type Defaults Enables/disables QR Code symbology. 0B10 On or Off Off On Off √ QR Code Minimum Set the minimum bar code label length to be less than or equal to maximum label length. 0B28 1 - 3500 1 3500 1 √ QR Code Maximum This feature specifies the maximum allowable length of a label. The length includes check and data characters, if applicable. Maximum Label Length should be greater than or equal to Minimum Label Length.
POSTAL CODES Accept. Input Factory I.D.# Max Description Min Code Parameter 2D Imager Scanner Type Defaults Enter 1 for On and 0 for Off US PostNet Enable Enables/ disables PostNet symbology. US Planet Enable Enables/ disables Planet symbology. Transmit US Postal Code check digit. 0910 On or Off Off On On √ 0911 On or Off Off On On √ 0912 On or Off Off On On √ Enables/ disables USPS 4State symbology.
IMAGING CONTROLS Accept. Input Factory I.D.# Max Description Min Code Parameter 2D Imager Scanner Type Defaults Enter 1 for On and 0 for Off Imager Illuminate Enable Imager Aim Mode Enable Aiming Beam Instructs the PDT to illuminate the scanning area (independent of any targeting beam) when using an imager. Toggles between two different operating modes for the targeting beam: Concurrent (Off): The targeting beam is turned on at the same time as an enabled illumination beam.
OTHER CONTROLS Scanner Type 2D Imager Lorax On or Off On On On √ √ √ 0025 Select symbology identifier to transmit immediately preceding scanned data: 0=None 1=DLM identifier before label: " " 2=AIM identifier before label: "]" 3=User defined identifier before label: 4=DLM identifier after label: " " 5=AIM identifier after label: "]" 6=User defined identifier after label: 00 01 00 √ √ √ Accept.
Scanner Type Description I.D.# Accept. Input Min Max Factory Laser 2D Imager Lorax Defaults Label Prefix Character sent immediately prior to symbology identifier (0=None). 0026 A string of Unicode characters. NUL NUL NUL √ √ √ Label Suffix Character sent immediately after final character in data (0=None). 0027 A string of Unicode characters. CR+LF CR+LF CR+LF √ √ √ Label Separator Character sent after each string in a sample where multiple strings exist.
Scanner Type I.D.# Accept. Input Min Max Factory Laser 2D Imager Lorax Defaults 002D 2 to 40 (step=1) 2 = 500 ms 40 = 10000 ms 20 20 20 √ √ √ Defines the volume of decoding sounds. FF20 0 to 7 = Soft to Loud 8 = lowers the volume by 1 9 = raises the volume by 1 7 7 7 √ √ √ Long Range Spot Enable Enable the use of a spot beam, if detected.
DATALOGIC ADC LABEL IDS Datalogic ADC Label IDs UPC-A = A M 2 of 5 = D Datamatrix = v UPC-E = E Code 93 = L Composite = s EAN-8 = G MSI = H Maxicode = w EAN 13 = M Trioptic = X PDF417 = s Code 39 = C Pharmacode 39 = Y MicroPDF = a Codabar = I GS1 DataBar-14 = P QR = c Code 128 = K GS1 DataBar Limited = Q Postal Codes = f I 2 of 5 = B GS1 DataBar Expanded = R S 2 of 5 = F Aztec = d
GLOSSARY Access Point A device that provides transparent access between Ethernet wired networks and IEEE 802.11 interoperable radio-equipped mobile units. Hand-held mobile computers, PDAs or other devices equipped with radio cards, communicate with wired networks using Access Points (AP). The mobile unit (mobile computer) may roam among the APs in the same subnet while maintaining a continuous, seamless connection to the wired network.
Decode To recognize a bar code symbology (e.g., Codabar, Code 128, Code 3 of 9, UPC/EAN, etc.) and analyze the content of the bar code scanned. Depth of Field (DOF) The portion of a scene that appears acceptably sharp in the image. Although a lens can precisely focus at only one distance, the decrease in sharpness is gradual on each side of the focused distance, so that within the DOF, the unsharpness is imperceptible under normal viewing conditions.
Host A computer that serves other mobile computers in a network, providing services such as network control, database access, special programs, supervisory programs, or programming languages. WLAN A Wireless Local Area Network links devices via a wireless distribution method (typically spread-spectrum or OFDM radio), and usually provides a connection through an access point to the wider internet. This gives users the mobility to move around within a local coverage area and still be connected to the network.
A piconet is a Bluetooth PAN that links up to eight devices. Each piconet is controlled by one master device, and up to seven slave devices at any one time. Any device may be a member of more than one piconet, changing its membership as a user moves from one area to another.
RAM Random Access memory. Data in RAM can be accessed in random order, and quickly written and read. RF Radio Frequency. RTC Real Time Clock. TDMA Time division multiple access (TDMA) is digital transmission technology that allows a number of users to access a single radio-frequency (RF) channel without interference by allocating unique time slots to each user within each channel. The TDMA digital transmission scheme multiplexes three signals over a single channel.
technology that permits communication within about 10 meters - in other words, a very short range.
INDEX A Accessories; 20 Available Models; 10 B Batteries and Maintenance; 22 Bluetooth®, Manager Device Setup; 72 Buttons; 63 C Charging the Batteries; 22 Cleaning the PDA; 29 Connections; 30 Connection to USB peripherals; 32 RS232 Connection; 34 USB Connection; 30 WLAN Connection; 35 WPAN Connections; 37 Control Panel; 62 CTIA Compliance; 150 D Data Capture; 45 Imager Data Capture; 47 Laser Data Capture; 45 Data Capture Configuration; 57 Datalogic Configuration Utility; 88 Datalogic Firmware Utility; 83 De
Suspend Management; 89 T Taskbar; 56 Technical Data; 91 Technical Features; 91 Test Codes; 96 U Using the Stylus; 43 V Volume Settings; 68 W WEEE Compliance; 151 Windows Connections; 70 Windows Mobile Phone; 78 Windows Mobile Welcome Wizard; 44 Windows Mobile® Device Center; 70 Wireless and Radio Frequencies Warnings; 40 Wireless Communication; 65 WWAN Connection; 38
Datalogic ADC S.r.l. Via S. Vitalino 13 40012 - Lippo di Calderara Bologna - Italy 11 dichiara che declares that the déclare que le bescheinigt ,daß das Gerät declare que el LYNX modelli con funzionalità radio 802.11a/b/g+BT models with 802.11a/b/g+BT radio feature modèles avec 802.11a/b/g+BT radio intégrés modelle mit 802.11a/b/g+BT radio-funktionalität modelos con funcionalidad radio 802.
EN 60950-1:2006 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1 : GENERAL REQUIREMENTS EN 62311:2008 ASSESSMENT OF ELECTRONIC AND ELECTRICAL EQUIPMENT RELATED TO HUMAN EXPOSURE RESTRICTIONS FOR ELECTROMAGNETIC FIELDS (0 HZ - 300 GHZ) Lippo di Calderara, June 27th 2011 Paola Chientaroli Quality Assurance Manager
Datalogic ADC S.r.l. Via S. Vitalino 13 40012 - Lippo di Calderara Bologna - Italy 11 dichiara che declares that the déclare que le bescheinigt ,daß das Gerät declare que el LYNX modelli con funzionalità radio Edge+BT+802.11a/b/g models with Edge+BT+802.11a/b/g radio feature modèles avec Edge+BT+802.11a/b/g radio intégrés modelle mit Edge+BT+802.11a/b/g radio-funktionalität modelos con funcionalidad radio Edge+BT+802.
ETSI EN 301 489-17 V2.1.1, MAY 2009 : ELECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM MATTERS (ERM); ELECTROMAGNETIC COMPATIBILITY (EMC) STANDARD FOR RADIO EQUIPMENT; PART 17: SPECIFIC CONDITIONS FOR 2,4 GHZ WIDEBAND TRANSMISSION SYSTEMS, 5 GHZ HIGH PERFORMANCE RLAN EQUIPMENT AND 5,8 GHZ BROADBAND DATA TRANSMITTING SYSTEMS ETSI EN 301 489-24 V1.4.
REFERENCES CONVENTIONS This manual uses the following conventions: “User” refers to anyone using an Lynx PDA. “PDA” and "Lynx" refer to Lynx PDA. “You” refers to the System Administrator or Technical Support person using this manual to install, configure, operate, maintain or troubleshoot an Lynx PDA. “Single Dock” refers to the Lynx Single Slot Dock. REFERENCE DOCUMENTATION For further information regarding Lynx refer to the SDK Help on-Line.
GENERAL VIEW B C D H K J I A M G E N L F A) B) C) D) E) F) G) Color Display* ON/OFF Power Key Receiver LEDs Front Scan Key Keyboard Stylus Remove protective film cover before use H) I) J) K) L) M) N) Laser Safety Label Loudspeaker Color Camera Flash Product Label MicroSD Card Slot (under battery) SIM Card Slot (under battery)
O Q R P O) Side Scan Key (right) P) Up/down Volume Keys S Q) Side Scan Key (left) R) Headset Connector S) Micro USB Charging Port T U
T) Data Capture/Laser Output Window U) Handylink™ Connector (host/slave)
Edited by Foxit Reader Copyright(C) by Foxit Corporation,2005-2009 For Evaluation Only. DRAFT REVISION Datalogic ADC Inc. Via S. Vitalino 13 40012 - Lippo di Calderara di Reno Bologna - Italy Lynx™ - Safety and Regulatory Addendum Ed.: 09/2012 ©2012 Datalogic ADC Inc. • ALL RIGHTS RESERVED. • Protected to the fullest extent under U.S. and international laws. • Copying, or altering of this document is prohibited without express written consent from Datalogic ADC Inc.
CONTENTS 1 1.1 1.2 BATTERIES AND MAINTENANCE .................................................... 1 Charging the Battery Pack .................................................................. 1 Replacing the Battery Pack ................................................................. 3 2 2.1 2.2 2.3 2.4 2.5 2.5.1 2.6 2.7 2.8 2.9 2.10 2.11 SAFETY REGULATIONS ................................................................... 6 General Safety Rules .......................................................
1 BATTERIES AND MAINTENANCE Rechargeable backup batteries and battery packs are not initially charged. Therefore the initial operation to perform is to charge them. See below. NOTE Annual replacement of rechargeable battery pack avoids possible risks or abnormalities and ensures maximum performance. CAUTION 1.1 CHARGING THE BATTERY PACK The battery pack autonomy varies according to many factors, such as the frequency of barcode scanning, RF usage, battery life, storage, environmental conditions, etc.
Even if the storage temperature range is wider, In order to achieve the longest battery life, store the terminal and the spare batteries between 20 to 30 ºC (68 to 86 ºF). NOTE The Batteries must be charged at a temperature ranging from 0° to +44 °C (+33.8° to +111.2 °F). The battery level may not be displayed correctly for some minutes after the disconnection if the Lynx is disconnected from power supply before the charging cycle is completed.
1.2 REPLACING THE BATTERY PACK To correctly replace the battery pack, proceed as follows. 1. Turn off the Lynx. 2. Shift the battery latch to the left and remove the battery pack: 3. Install the new battery pack, first insert the bottom (contacts) and then the upper side of the battery pack into the slot. Press until the battery latch clicks.
Installing, charging and/or any other action should be done by authorized personnel and following this manual. WARNING The battery pack may get hot, explode, ignite, and/or cause serious injury if exposed to abusive conditions. If the battery pack is replaced with an improper type, there is risk of explosion.
WARNING Do not disassemble or modify (i.e. bend, crush or deform) the battery pack. The battery pack contains safety and protection devices, which, if damaged, may cause the battery pack to generate heat, explode or ignite. In case of leakage of liquid from the battery, avoid contact with liquid the skin or eyes. If the contact occurs, immediately wash the affected area with water and consult a doctor. Do not solder directly onto the battery pack. Do not expose the battery pack to liquids.
2 SAFETY REGULATIONS NOTE 2.1 2.2 Read this manual carefully before performing any type of connection to the Lynx mobile computer. The user is responsible for any damages caused by incorrect use of the equipment or by inobservance of the indication supplied in this manual. GENERAL SAFETY RULES Use only the components supplied by the manufacturer for the specific Lynx being used.
2.3 LASER SAFETY The laser light is visible to the human eye and is emitted from the window indicated in the figure. This information applies to both laser models and the Lynx Imager Aiming System.
I D F La luce laser è visibile all'occhio umano e viene emessa dalla finestra indicata nella figura. Die Laserstrahlung ist für das menschliche Auge sichtbar und wird am Strahlaustrittsfenster ausgesendet (siehe Bild). Le rayon laser est visible à l'oeil nu et il est émis par la fenêtre désignée sur l'illustration dans la figure. La luz láser es visible al ojo humano y es emitida por la ventana indicada en la figura.
ENGLISH The following information is provided to comply with the rules imposed by international authorities and refers to the correct use of your mobile computer. STANDARD LASER SAFETY REGULATIONS This product conforms to the applicable requirements of both CDRH 21 CFR 1040 Subchapter J and IEC 60825-1:2007 at the date of manufacture. For installation, use and maintenance, it is not necessary to open the device. CAUTION Do not attempt to open or otherwise service any components in the optics cavity.
Non tentare di accedere allo scomparto contenete i componenti ottici o di farne la manutenzione. ATTENZIONE L’apertura dello scomparto, o la manutenzione di qualsiasi parte ottica da parte di personale non autorizzato, potrebbe violare le norme della sicurezza. Il sistema ottico può essere riparato solamente alla fabbrica. L'utilizzo di procedure o regolazioni differenti da quelle descritte nella documentazione può provocare un'esposizione pericolosa a luce laser visibile.
Jegliche Änderungen am Gerät sowie Vorgehensweisen, die nicht in dieser Betriebsanleitung beschrieben werden, können ein gefährliches Laserlicht verursachen. ACHTUNG Der Produkt benutzt eine Laserdiode. Obwohl zur Zeit keine Augenschäden von kurzen Einstrahlungen bekannt sind, sollten Sie es vermeiden für längere Zeit in den Laserstrahl zu schauen, genauso wenig wie in starke Lichtquellen (z.B. die Sonne).
ATTENTION L’utilisation d’instruments optiques avec le scanneur augmente le danger pour les yeux. Les instruments optiques comprennent les jumelles, les microscopes, les lunettes et les verres grossissants. ESPAÑOL Las informaciones siguientes son presentadas en conformidad con las disposiciones de las autoridades internacionales y se refieren al uso correcto del terminal.
2.4 LED CLASS LED illuminators integrated in the LYNX models with SE-4500 imager engine are compliant with exempt risk group requirements according to IEC62471:2006 and EN62471:2008. Flash LED integrated in the LYNX models with camera is blue light hazard risk group 1 according to IEC62471:2006 and EN62471:2008 2.
2.5.1 Information for the User ENGLISH Contact the competent authority responsible for the management of radio frequency devices of your country to verify any possible restrictions or licenses required. Refer to the web site http://europa.eu.int/comm/enterprise/rtte/spectr.htm for further information. ITALIANO Prendi contatto con l'autorità competente per la gestione degli apparati a radio frequenza del tuo paese, per verificare eventuali restrizioni o licenze.
2.6 FCC COMPLIANCE FCC Regulations: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
2.7 RF EXPOSURE INFORMATION (SAR) This model device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard for wireless devices employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg.
2.8 INDUSTRY CANADA COMPLIANCE Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
2.9 SAR COMPLIANCE 1. For the used worst case positions, the portable device Lynx from Datalogic (FCC ID: U4G0070 and U4G0073) is in compliance with the IC RSS 102 Issue 4 [RSS 102] and Federal Communications Commission (FCC) Guidelines [OET 65] for uncontrolled exposure. SAR assessment in body worn was conducted with a distance of 15 mm between the housing of the handheld and the flat phantom. 2.
2.11 WEEE COMPLIANCE Informazione degli utenti ai sensi della Direttiva Europea 2002/96/EC L’apparecchiatura che riporta il simbolo del bidone barrato deve essere smaltita, alla fine della sua vita utile, separatamente dai rifiuti urbani.
éviter les retombées négatives pour l'environnement et la santé dérivant d'une élimination incorrecte récupérer les matériaux dans le but d'une économie importante en termes d'énergie et de ressources Pour obtenir des informations complémentaires concernant l'élimination, veuillez contacter le fournisseur auprès duquel vous avez acheté le produit ou consulter la section consacrée au site Web www.mobile.datalogic.com.
Edited by Foxit Reader Copyright(C) by Foxit Corporation,2005-2009 For Evaluation Only. Datalogic ADC s.r.l. Via S. Vitalino 13 40012 – Calderara di Reno Bologna - Italy EC-062 rev. 0 dichiara che declares that the déclare que le bescheinigt ,daß das Gerät declare que el LYNX 12 modelli con funzionalità radio 802.11b/g/n+BT models with 802.11b/g/n+BT radio feature modèles avec 802.11b/g/n+BT radio intégrés modelle mit 802.11b/g/n+BT radio-funktionalität modelos con funcionalidad radio 802.
ETSI EN 300 328 V 1.7.1 :2006 ELECTROMAGNETIC COMPATIBILITY AND RADIO MATTERS (ERM); WIDEBAND SPECTRUM TRANSMISSION SYSTEMS; DATA TRANSMISSION EQUIPMENT OPERATING IN THE 2,4GHZ ISM BAND AND USING WIDE BAND MODULATION TECHNIQUES; HARMONIZED EN COVERING ESSENTIAL REQUIREMENTS UNDER ARTICLE 3.
Edited by Foxit Reader Copyright(C) by Foxit Corporation,2005-2009 For Evaluation Only. Datalogic ADC s.r.l. Via S. Vitalino 13 40012 – Calderara di Reno Bologna - Italy EC-063 rev. 0 dichiara che declares that the déclare que le bescheinigt ,daß das Gerät declare que el LYNX 12 modelli con funzionalità radio Edge+BT+802.11b/g/n models with Edge+BT+802.11b/g/n radio feature modèles avec Edge+BT+802.11b/g/n radio intégrés modelle mit Edge+BT+802.
ETSI EN 301 489-7 V1.3.1 :2005 ELECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM MATTERS (ERM); ELECTROMAGNETIC COMPATIBILITY (EMC) STANDARD FOR RADIO EQUIPMENT AND SERVICES; PART 7: SPECIFIC CONDITIONS FOR MOBILE AND PORTABLE RADIO AND ANCILLARY EQUIPMENT OF DIGITAL CELLULAR RADIO TELECOMMUNICATIONS SYSTEMS (GSM AND DCS) ETSI EN 301 489-17 V2.1.
IEC 60950-1:2005 +A1 :2009 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY PART 1 : GENERAL REQUIREMENTS EN 50332-2 :2003 SOUND SYSTEM EQUIPMENT - HEADPHONES AND EARPHONES ASSOCIATED WITH PORTABLE AUDIO EQUIPMENT - MAXIMUM SOUND PRESSURE LEVEL MEASUREMENT METHODOLOGY AND LIMIT CONSIDERATIONS - PART 2: MATCHING OF SETS WITH HEADPHONES IF EITHER OR BOTH ARE OFFERED SEPARATELY IEC 60825-1 :2007 SAFETY OF LASER PRODUCTS - PART CLASSIFICATION AND REQUIREMENTS IEC 62471 :2006 EN 62471 :2008 PHOTOBIOLOGICAL LAMPS