RF Systems Manual
PSC Scanning, Inc. 959 Terry Street Eugene, Oregon 97402 Telephone: (541) 683-5700 Telefax: (541) 345-7140 PSC, the PSC logo, Quadralogic and PowerScan are registered trademarks of PSC Inc. All other trademarks and trade names referred to herein are property of their respective owners. All rights reserved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written permission of PSC Inc.
TABLE OF CONTENTS Introduction................................................................................................................................1 About This Manual ..................................................................................................1 References ..............................................................................................................1 Product Description ...........................................................................................
Scanner vs. Base Station Features ...................................................................... 38 Interface (I/F) Selection ........................................................................................ 39 Universal Keyboard Wedge I/F Selection ............................................................. 42 Terminal/Keyboard Settings ................................................................................. 43 RF Beeper Settings ...................................................
Introduction About This This systems manual provides information and instructions to connect Manual and configure your PowerScan™ RF system. The following sections are included in the manual: • Introduction presents general information about the contents of this manual and about the system. • Quick Start Instructions provide easy to follow procedures for installing your system quickly. • Using the PowerScan RF System provides details about scanning basics, system controls and indicators.
Product The PowerScan™ RF scanner is designed for durability, with high Description impact-resistant material and protective rubber cushioning at every point of impact, and it also provides the unleashed freedom of Radio Frequency (RF) communication with your host system. Scanner and Base Station nomenclature and labeling are shown in Figure 1 and Figure 2 below. Figure 1.
Figure 2. Base Station Labels and Nomenclature 2 3 5 4 1 6 E ID BAS PSC INC. 959 Terry Street Eugene, OR 97402 U.S.A. ACN N263 C X TX/R GE R CHA ER POW US LISTED NWGQ 2Z78 14 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference, including interference that may cause undesired operation.
Laser Cautions The PowerScan RF bar code scanner is certified in the U.S. to conform to the requirements of DHHS/CDRH 21CFR Subchapter J for Class II laser products. Class II products are not considered to be hazardous. The scanner contains a Visible Laser Diode (VLD) at a wavelength of 650670 nanometers and is designed so that there can be no human access to harmful levels of laser light during normal operation, user maintenance, or during prescribed service operations.
Radio Frequency Interference This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Quick Start Instructions Unpacking and After unpacking your new Base Station, check the contents of the shipInspecting the ping carton to ensure all the items you ordered are included: Base Station • PowerScan™ Scanner Base Station • Interface Cable • Power Supply (AC Adapter or Forklift DC Converter) • Systems Manual (this manual) • Programming Guide • Optional Accessories that you ordered. (The Base Station can be purchased with or without accessory kits.
Installing the Battery To assure maximum usage, batteries should always be fully charged before their initial use. (See Battery Charging and Maintenance on page 12.) NOTE Orient the battery as shown in Figure 3, then push it into the scanner until it snaps in place. To remove the battery, push in on the release tabs on both sides of the battery’s base and pull it straight out of the scanner. Figure 3. Installing the Battery 1 1.
Verifying Scanner Operation Once a charged battery has been installed in the scanner, scan the sample bar codes in Appendix A that correspond to the symbologies your scanner is programmed to read. If unsure how to do this, see the section on How to Scan in this manual. The system may signal with one or a combination of indicators depending upon how the scanner and Base Station are programmed to respond (see LED and Beeper Indications for details).
2. Consult your Host Terminal manual to determine the required communication parameters for the Host Terminal (e.g., baud rate, parity, etc.) and, if necessary, modify the programmed parameters to be compatible with those requirements. Scanner and Base Station programming is performed using one of the following: - Configurator Express™ Programming Software - PowerScan™ Bar Code Scanner Programming Guide See References for more information about how to obtain software and manuals for this product.
Figure 5. Connecting Power to the Base Station 5. Apply power to the Host Terminal. 6. Verify communication with the Host Terminal by aiming the linked scanner at a sample bar code from Appendix A, and pulling the trigger (see How to Scan for tips about scanning bar codes). Confirm that the scanner/Base Station sent the data to the host terminal. If not, see the section, Maintenance and Troubleshooting. Once all communications are verified, the system is ready for use.
The existing Base Station system configuration can be automatically downloaded to the scanner. This automatic download feature is configurable and can be disabled. See the section, Common Configuration for more information about this feature. If downloading occurs, a slight delay with link verification announcement will occur.
• LED and Beeper Indications • Maximizing Signal Range • Three-Position Lock Battery Charging and Maintenance NOTE When the scanner is in use, a low battery condition is indicated by a repeated two-flash signal from the scanner’s green LED every time the trigger is pulled before the laser is enabled. This indicator may have been disabled via custom programming. See LED and Beeper Indications for more information.
NOTE Batteries will not charge if their temperature is below 0°C (30°F). If a battery that is too cold is inserted into the Base Station, the Charge LED will not illuminate. Tips for Nickel Metal Hydride (NiMH) batteries will better hold a charge if Extending allowed to discharge at least once a week. The chemical reactions that Battery Life correspond to charge and discharge in a rechargeable battery should occur to obtain the maximum number of charge/discharge cycles in the battery.
Figure 7. Using the Four Station Charger Accessory 1 2 1. 14 Device Power LED 2.
How to Scan Figure 8 illustrates some tips to help get the best scanning results: 1. The scanner must be pointed at a slight angle to the bar code. Do not hold the scanner perpendicular to the bar code. 2. The laser beam must cross the entire bar code. The scanner cannot correctly read if the entire bar code is not scanned. Figure 8.
Depth of Field There are currently four different range models for the RF scanner. Depending upon the model type of your scanner, you’ll need to hold the unit at a given distance from the bar code to achieve optimum scanning results. The following diagrams provide depth of field information for each of the models when scanning grade A, Code 39 bar codes: Standard Range (SR), High Density (HD), Long Range (LR) and Extra Long Range (XLR). Definition of a "mil" A "mil" is equal to 0.001 inches.
See the section titled, Definition of a "mil" for more information about reading this chart. Measurements are based on HD models set with the standard 28° scan width (as opposed to the Half Angle setting of 14°). Reference the Programming Manual for more information about the Half Angle feature. NOTE Specifications are subject to change without notice. Figure 10. Depth of Field (HD) Depth of Field FRONT OF SCANNER Paper Labels (HD decoded model, Code 39) 3 mil 4 mil 5 mil 7.
See the section titled, Definition of a "mil" for more information about reading this chart. Measurements are based on LR models set with the a 14° scan width (as opposed to the alternate Full Angle setting of 28°). Reference the Programming Manual for more information about the Half Angle feature. NOTE Specifications are subject to change without notice. Figure 11. Depth of Field (LR) Depth of Field FRONT OF SCANNER Paper Labels (LR decoded model, Code 39) 7.
See the section titled, Definition of a "mil" for more information about reading this chart. Measurements are based on XLR models set with a 10° scan angle width. NOTE Specifications are subject to change without notice. Figure 12.
Active The active (enabled) bar code symbologies in the standard factory Symbologies defaults are: • Code 39 (C39) • Code 128 (C128) • Interleaved 2 of 5 (I 2 of 5) Your scanner should be pre-programmed with these standard factory default settings, unless... ...it was shipped to you programmed with unique, customer configuration settings. ...you or another user have made changes to scanner programming.
LED and Beeper Indications The Base Station LED indicators and the scanner’s LEDs and beeper are used to announce system status and perform other useful signals. The tables below list the default function of each of the various indicators. Some LED and beeper indications can be disabled or modified via scanner programming. The tables indicate the default behavior of the indicators, with shaded rows representing features that are programmable. NOTE Table 1.
Table 2. Scanner YELLOW LED Functions LED INDICATION Laser on indication DURATION On Steady COMMENT The yellow LED illuminates whenever the laser is on. Table 3. Scanner BEEPER Functions SPEAKER INDICATION Scanner Not Currently Linked DURATION Six beeps consisting of 20 ms on, 20 ms off COMMENT Indicates a bar code was read before the scanner was linked to a Base Station.
SPEAKER INDICATION Transmission Error Beep DURATION High, then low, then high, then low. Indicates a scanner has been successfully linked to a base station. High, then medium, then low. Indicates a scanner has been successfully unlinked from a base station. Varies. Consists of a long tone followed by multiple short tones. Enables service technicians to identify Field Replaceable Unit (FRU) errors. Unlink Beep Systems Manual Indicates unsuccessful transmission to the host.
Table 4. Base Station LED Functions LED INDICATION DURATION Lit for variable timea TX/RX (Transmit/Receive) Continuous rapid flashing at power-up Varies. Consists of a long flash followed by multiple short flashes. Continuous flashing Charge (Battery) Power COMMENT Indicates communications activity to or from the Base Station. Indicates a broken radio. Enables service technicians to identify Field Replaceable Unit (FRU) errors.
Maximizing Signal Range Here are a few tips about how you can optimize your system installation to allow the scanner greater roving distance from its linked Base Station while maintaining clear communication between the devices. Systems Manual • Minimize obstructions between the scanner and its Base Station. While the system is capable of communicating through walls, a clean line of sight will always increase the scanner’s signal range from the Base Station.
Three-Position The Base Station is equipped with a three-position lock to allow a scanLock ner to be secured in the Base Station in horizontal, vertical, and forklift installations. Figure 13. Using the Three-Position Lock 1 2 3 26 1. Top position: Vertical Forklift Mount Lock 2. Middle position: Vertical (Wall) Mount Lock 3.
Mounting the Base Station The Base Station can be secured to varying surfaces to ensure a permanent, stable installation. Several options are available. Horizontal (Table or Countertop) Mounting Using Key Slots Systems Manual Refer to Figure 14 and follow these steps: 1. Once you have identified the desired area for permanent Base Station installation, use the mounting template included with this manual to mark the position of its "key slot" mounting screws. 2. Install three #8 x 1" (4.1mm x 25.
Figure 14. Mounting Using Key Slots 2 1 BASE ID X TX/R GE CHAR WER PO 1. Key Slots Using Mounting Flanges 28 2. #8 x 1" (4.1mm x 25.4mm) Pan Head Screw Refer to Figure 15a and follow these steps: 1. Once you have identified the desired area for permanent Base Station installation, hold the unit in place and mark the position of screws using the "mounting flanges." 2. Start and remove four screws (provided) at the marked positions in the mounting surface. 3.
Figure 15. Mounting Using Flanges or Two-sided Tape 4 2 3 BASE ID X TX/R GE CHAR WER PO 1 a b 1. Mounting Flanges (4) 3. Two-sided Tape Strips 2. 4 Screws (provided) 4. Backing Mounting Using TwoSided Tape You can also affix the Base Station to a surface using the two-sided tape strips provided with the unit. Simply remove the backing from one side of the strips and apply them to the bottom of the Base Station as shown in Figure 15b.
Post or Forklift To secure the Base Station to a post or forklift frame, refer to Figure 16 Mounting and follow these steps: 1. Verify that the desired mounting area offers sufficient space for safe forklift operation and will not present a hazard for operators or potentially damage the mounted device(s). 2. Ensure that power and interface cables are securely connected and routed in the channels provided in the back of the Base Station. 3.
RF Programmable Features Use the special programming bar codes contained in this section to set features that are unique to RF models of PowerScan™ bar code scanners. To program other features that are common to all models, use one of the following: - Configurator Express™ On-Screen Programming Kit - PowerScan™ Programming Guide See References on page 1 for more information about how to obtain kits, software and manuals for this product.
Programming The RF system’s programmable feature settings can be modified to Overview accommodate your unique requirements. Listed below are the various methods to configure scanner and Base Station units: Base Stations and the scanners linked to them must possess compatible configuration files. NOTE Scanner 1. The Base Station’s configuration files can be automatically downloaded to the scanner at the time of linking.
Base Station Base Station configuration is primarily performed by first programming a scanner with the desired options, then downloading the configuration to the Base Station from that scanner. CAUTION Verify that the scanner and Base Station host interface types (RS-232, Keyboard Wedge, etc.) are matched before attempting to download any configuration files or perform any custom programming sessions. Go to Interface (I/F) selection on page x and set the scanner to the Base Station’s I/F type.
The Scanner programming allows you to customize the scanner’s configuProgramming ration to match your specific needs. A typical programming session is Session conducted as follows: 1. Scan the SET bar code at the top of the page. The scanner will emit one beep, indicating it has read the bar code and the green LED will flash on and off slowly while the scanner remains in Programming Mode. Normal scanning functions are disabled. 2. Scan the programming bar codes(s) to make the desired changes.
4. Systems Manual Maintain a record of all changes made to ensure that you know if the original factory settings have been changed. Use the following table to log your custom configuration changes.
Common Configuration Disable Set Maximum Linked Scanners 8 Source-Radio Identification (ID) Don’t Include Low Battery LED Indication Enable Programming To modify a scanner feature (item), the programming bar codes conSequence tained in this manual must be scanned in a given sequence depending upon the feature being programmed (as shown in Table 5). There are three possible programming sequences: A.
Table 5. Programming Sequence SET A ITEM TAG ITEM VALUE END/RESET 1 2 3 SET ENABLE NEW FEATURE END 1 2 345 6 0 B SET C Systems Manual ENABLE NEW FEATURE USING THE FOLLOWING SETTINGS...
Scanner vs. Some programming features are specific to either the scanner (handBase Station held unit) or the Base Station, while others are applicable to both. Each Features feature in this manual is marked with an indicator as to which unit(s) it is applicable. Feature is specific to scanner ONLY Feature is specific to Base Station ONLY Feature is applicable to scanner and Base Station.
Interface (I/F) It is very important that the scanner and Base Station are each configSelection ured to operate with the same interface (I/F) type as the host terminal. NOTE The Base Station uses a “smart” cable, which automatically sets the Base Station to the correct I/F upon power-up and connection to the appropriate host.
Enable Keyboard Wedge --------Type Aa Enable Keyboard Wedge Type B --------- Enable Keyboard Wedge Type C --------- Enable Keyboard Wedge Type D --------- Enable Keyboard Wedge Type E --------- Enable Keyboard Wedge Type F --------Enable Keyboard Wedge Type G --------- Enable Keyboard Wedge Type H --------- Enable Keyboard Wedge Type I --------Enable Keyboard Wedge Type J --------- END ------------------------------------------ a.
Table 6.
Universal To activate the Universal Keyboard Wedge interface, follow these Keyboard instructions: Wedge I/F 1. Scan the START bar code. Selection 2. Determine the I.D. of the terminal/keyboard. This information is available in the Universal Keyboard Wedge Connectivity Guide (R44-2039), or refer to the Terminal/Keyboard Settings section below for a listing of the most common keyboard I.D.s. 3. Scan the ACTIVATE UNIVERSAL KEYBOARD WEDGE INTERFACE bar code on the following page. 4.
Terminal/ The list below contains the most common terminal/keyboard types. If Keyboard your specific system is not listed below, consult the Keyboard Wedge Settings Connectivity Guide (P/N R44-2039) for a detailed listing of terminal/ keyboard types. A copy of the guide can be obtained from the internet at www.pscnet.com, or call your dealer for customer support information. Systems Manual Keyboard Terminal I.D.
RF Beeper The RF version of the scanner exhibits different beeper behavior than Settings standard (non-RF) models. For more information about RF beeper indications, see the section, LED and Beeper Indications. NOTE The following descriptions highlight configurable beeper functions that are unique to RF handheld scanners. All other beeper functions supported by the standard version of the scanner are supported by RF models.
RF When to Beep Feature is specific to scanner ONLY Several options are available to specify how the RF handheld scanner will beep to indicate a good read. Settings are based on the enable/disable status desired for three selectable beep indications: • Good Read Beep • Acknowledgement (ACK) Beep • Transmission Error Beep The available options are described and numbered in Table 7 to correspond with the programming bar codes provided for this feature.
RF When to Beep Options (continued) SET ------------------------------------------- When to Beep Option #0 --------- When to Beep Option #1 --------- When to Beep Option #2 --------- When to Beep Option #3 --------- When to Beep Option #4 --------- When to Beep Option #5 --------- When to Beep Option #6 --------- When to Beep Option #7 --------- END ------------------------------------------ 46 PowerScan™ RF Scanner
RF Beeper Volume Feature is specific to scanner ONLY The volume at which the beeper sounds for ACK, transmission error, link, or unlink beeps (but not the good read beep1) are all affected by this setting. Select volume #1 (25% duty cycle), volume #2 (35% duty cycle), or volume #3 (50% duty cycle). SET ------------------------------------------- RF Beeper Volume #1 --------- RF Beeper Volume #2 --------- RF Beeper Volume #3 --------- END ------------------------------------------ 1.
RF Beeper Frequency Feature is specific to scanner ONLY This setting affects the frequency at which the ACK beep is sounded, and is independent of the frequency setting for the good read beep. When the ACK beep is sounded at a different frequency than the good read beep, this can provide a clearer distinction between the tones. Select low frequency (760Hz), medium frequency (1250Hz), or high frequency (2400Hz).
RF Beep Duration Feature is specific to scanner ONLY The duration of time that an ACK beep is sounded is selectable using this setting. RF beep duration can be set in increments of 10 ms (tolerance of +/- 10%) from 0 to 2.55 seconds. SET ------------------------------------------- Set RF Beep Duration --------- Scan three digits representing the desired duration using the Number Pad in Appendix B, padded with leading zeros (example: 008 = 80ms, 025 = 250ms, 100 = 1 second, etc.
Radio Transmit Power Feature is applicable to scanner and Base Station. NOTE Remember, programming changes to the Base Station have no effect until the new configuration is downloaded via the feature Transmit Scanner Configuration to Base Station on page 33. The power level at which the radio signal is transmitted between the devices is selectable to be either low or high.
RF Channel Selection Feature is applicable to scanner and Base Station. NOTE Channel selection bar codes are of the type C programming sequence category (see Programming Sequence on page 36), and do not require you to scan accompanying SET or END bar codes. Radio communications between the handheld scanner and its linked Base Station can be carried over one of ten different allowable frequencies (channels). Select alternate channels to improve communications between devices in noisy RF environments.
52 Select Radio Channel 0 --------- Select Radio Channel 1 --------- Select Radio Channel 2 --------- Select Radio Channel 3 --------- Select Radio Channel 4 --------- Select Radio Channel 5 --------- Select Radio Channel 6 --------- Select Radio Channel 7 --------- Select Radio Channel 8 --------- Select Radio Channel 9 --------- PowerScan™ RF Scanner
Transmission Retries Before Message Timeout Feature is applicable to scanner and Base Station. NOTE Remember, programming changes to the Base Station have no effect until the new configuration is downloaded via the feature Transmit Scanner Configuration to Base Station on page 33. When the scanner attempts to transmit data to the Base Station, communication may not always occur on the first try due to interference, signals from other scanners in the queue, etc..
54 2 Retries --------- 3 Retries (recommended) --------- 4 Retries --------- 5 Retries --------- 6 Retries --------- 7 Retries --------- 8 Retries --------- 9 Retries --------- PowerScan™ RF Scanner
10 Retries --------- 11 Retries --------- 12 Retries --------- 13 Retries --------- 14 Retries --------- 15 Retries --------- END ------------------------------------------ Systems Manual 55
Wait Time for ACK Feature is applicable to scanner and Base Station. NOTE Remember, programming changes to the Base Station have no effect until the new configuration is downloaded via the feature Transmit Scanner Configuration to Base Station on page 33. This setting defines a time period allowed once the scanner has sent data to the Base Station for that Base Station to send an acknowledgement (ACK) back to the scanner, signalling receipt of the data.
Wait Time For Scanner Power Shutdown Feature is specific to scanner ONLY To conserve battery life, the handheld scanner can be automatically shut down when it has not been in use for a given period. A trigger pull or other stimulus will then be required to reactivate the scanner. The idle duration determines how long the scanner stays on/active after each use. Range for this feature is a setting of 1 to 120 seconds in one-second increments. A setting of one second is recommended.
Wait Time Between Retries of Failed Transmission Feature is applicable to scanner and Base Station. NOTE Remember, programming changes to the Base Station have no effect until the new configuration is downloaded via the feature Transmit Scanner Configuration to Base Station on page 33.
SET ------------------------------------------- Set Wait Time Between Retries of Failed Transmission --------- Scan three digits representing the desired delay using the Number Pad in Appendix B. Be sure the number is padded with leading zeros (example: 005 = 5ms, 065 = 65ms, 250 = 250ms, etc.), then scan the END bar code.
HACK Transmit Options Feature is applicable to scanner and Base Station. NOTE Remember, programming changes to the Base Station have no effect until the new configuration is downloaded via the feature Transmit Scanner Configuration to Base Station on page 33. A Host Acknowledgement (HACK) message is a signal sent to the scanner via the Base Station indicating the host has received bar code data previously transmitted by that scanner.
SET ------------------------------------------- HACK upon receipt of scanner transmission --------- HACK upon Base Station transmission to the host --------- HACK after host transitions CTS line (RS-232 ONLY) --------- HACK after host returns ACK (RS-232 ONLY) --------- END ------------------------------------------ Systems Manual 61
Wait Time For HACK From Host Feature is specific to scanner ONLY This setting specifies the time the scanner must wait to receive a HACK message back from the host before giving up and registering a transmission error. Selectable range for this wait time is 20ms to 5.1 seconds in 20ms increments. It is recommended that this value be set at no less than one second. NOTE Host turnaround (ACK) time is variable.
Drop Links on Reset Option Feature is specific to Base Station ONLY NOTE Remember, programming changes to the Base Station have no effect until the new configuration is downloaded via the feature Transmit Scanner Configuration to Base Station on page 33. When enabled, this option causes the Base Station to drop its links to any and all scanners whenever power is reset/cycled.
Drop Oldest Links Option Feature is specific to Base Station ONLY NOTE Remember, programming changes to the Base Station have no effect until the new configuration is downloaded via the feature Transmit Scanner Configuration to Base Station on page 33. This feature can be enabled to better manage the linking of new scanners to a multi-point system.
Common Configuration Feature is applicable to scanner and Base Station. NOTE Remember, programming changes to the Base Station have no effect until the new configuration is downloaded via the feature Transmit Scanner Configuration to Base Station on page 33. When this option is enabled, the Base Station attempts to share its configuration with a scanner as that scanner links to the Base Station.
DISABLE Common Configuration --------- END ------------------------------------------ 66 PowerScan™ RF Scanner
Set Maximum Linked Scanners Feature is specific to Base Station ONLY NOTE Remember, programming changes to the Base Station have no effect until the new configuration is downloaded via the feature Transmit Scanner Configuration to Base Station on page 33. By default, as many as eight scanners can be linked to one Base Station. This feature allows you to further limit allowable linked scanners. Designate a number of scanners that can link from one to eight.
Maximum Linked Scanners = 5 --------- Maximum Linked Scanners = 6 --------- Maximum Linked Scanners = 7 --------- Maximum Linked Scanners = 8 --------- END ------------------------------------------ 68 PowerScan™ RF Scanner
Source-Radio Identification (ID) Feature is specific to Base Station ONLY NOTE Remember, programming changes to the Base Station have no effect until the new configuration is downloaded via the feature Transmit Scanner Configuration to Base Station on page 33. This feature allows you to include source-radio identification1 (represented by six ASCII bytes) along with bar code data transmitted to the host. Enable this feature to identify the individual scanner sending a given data transmission.
SET ------------------------------------------- Do not include sourceradio ID --------- Include source-radio as prefix --------- Include source-radio as suffix --------- END ------------------------------------------ 70 PowerScan™ RF Scanner
Low Battery LED Indication Feature is specific to scanner ONLY If this feature is enabled and the battery power in the scanner is low, the scanner’s green LED flashes twice every time the trigger is pulled.
Maintenance and Troubleshooting Scanner The scan window will require occasional cleaning to remove smudges, Maintenance dust and other debris. To ensure optimal performance, clean the Scan Window using a soft cloth or lens tissue dampened with isopropyl alcohol (or equivalent). See Figure 17. The scanner body can also be cleaned using this method. Figure 17. Cleaning the Scan Window Base Station The Base Station requires no routine maintenance.
Troubleshooting Troubleshoot your RF scanning system by performing the following checks: For the RF system, ensure that... • the battery is charged. See Battery Charging and Maintenance on page 12. • the battery is properly installed. See Installing the Battery on page 7. • the scanner is linked to the desired Base Station. See Linking the Scanner to a Base Station on page 10.
If the Scanner Here are reasons why your scanner may not be linked with the Base Fails to Link Station: with the Base • There may be too many scanners attempting a link with the same Base Station. A maximum of eight scanners may link Station with one Base Station at a given time. Reference the section, Set Maximum Linked Scanners for more information..
NOTES Systems Manual 75
NOTES 76 PowerScan™ RF Scanner
NOTES Systems Manual 77
Standard Warranty PSC warrants to Customer that PSC’s products will be free from defects in materials and workmanship for a period of two years from product shipment. In order to obtain service under this Warranty, Customer must notify PSC of the claimed defect before the expiration of the Warranty period and obtain from PSC a return authorization number for return of the product to designated PSC service center.
Appendix A Sample Bar Codes Use these test bar codes to check the scanner’s ability to read the various symbologies represented. Code 128 C o d e 1 2 8 . T e s t Code 39 C O D E 3 9 . T E S T Interleaved 2 of 5 0 1 2 3 4 5 6 7 8 9 Standard 2 of 5 1 2 3 4 5 6 7 8 9 0 Codabar A $ 9 9 . 9 5 A Code 93 C o Systems Manual d e 9 3 .
MSI/Plessey 14476925 4 UPC-A 00112 0 23344 0 4 9 UPC-A with 2 digit Add-on 0 60992 01118 7 6 9 0 0 0 UPC-A with 5 digit Add-on 0 08029 51041 8 UPC-E 0 998875 0 EAN-8 0021 0126 EAN-13 1 A-2 101234 567891 PowerScan™ RF Scanner
Appendix B Number Pad 0 → 1 → 2 → 3 → 4 → 5 → 6 → 7 → 8 → 9 → Systems Manual B-1
NOTES B-2 PowerScan™ RF Scanner
DECLARATION OF CONFORMITY PSC hereby declares that the Equipment specified below has been tested and found compliant to the following Directives and Standards: Directives: EMC 89/336/EEC Low Voltage 73/23/EEC Standards: ETS 300 683 ETS 300 220-1 EN60825 EN50082-1 Equipment Type: Product: EN60950 Bar Code Scanning Equipment PowerScan™ RF Bar Code Scanner Charles W. Vanlue Director, Corporate Quality PSC, Inc. 959 Terry Street Eugene, OR 97402 U.S.A.
Asia Pacific Italy PSC Hong Kong Hong Kong Telephone: [852]-2-584-6210 Fax: [852]-2-521-0291 PSC S.r.l. Vimercate (MI), Italy Telephone: [39] (0) 39/62903.1 Fax: [39] (0) 39/685496 Australia Japan PSC Asia Pacific Pty Ltd. North Ryde, Australia Telephone: [61] 0 (2) 9878 8999 Fax: [61] 0 (2) 9878 8688 PSC Japan K.K. Shinagawa-ku, Tokyo, Japan Telephone: 81 (0)3 3491 6761 Fax: 81 (0)3 3491 6656 France Latin America PSC Sarl LES ULIS Cedex, France Telephone: [33].01.64.86.71.00 Fax: [33].01.64 46.