Quick Guide

Color: Black
Paper Material: White paper 150g
Size: 105 x 148.5 mm (per 1 page)
ONT QIG print specification
Folding line
Cutting line
Folding
Front CoverBack Cover
Quick Installation Guide
H680GM
V 2.0
Copyright 2020 ⓒ DASAN Zhone Solutions, Inc. All Rights Reserved.
DASAN Tower, 49, Daewangpangyo-ro 644 Beon-gil, Bundang-gu, Seongnam-si, Gyeonggi-do,
463-400 KOREA
DASAN Zhone Solutions
4. Web Access
You can access the unit through a web browser by using the following steps.
① Connect LAN port of the unit to your PC using Ethernet cable.
② Configure IP assignment of your PC to DHCP (dynamic assignment).
How to configure dynamic IP on your PC is as follows:
For Windows XP:
Start > Setting > Network Connections > Local Area Connection double
click > Internet Protocol (TCP/IP) double click > Obtain an IP address
automatically and Obtain DNS server address automatically selection >
OK
For Windows 7:
Start > Control Panel > View network status and tasks under Network and
Internet (View by: Category) > Change adapter settings on the left menu >
Local Area Connection right-click > Properties > Internet Protocol Version
4 (TCP/IPv4) double click > Obtain an IP address automatically and Obtain
DNS server address automatically selection > OK
The PC will be allocated IP address automatically through the unit.
③ Open a web browser, and enter http://192.168.1.1 in a URL field.
④ Type admin/vertex25 in user name/password field, and log into the system.
Initial page is displayed.
※ For Web Access User/PW and WiFi SSID/WiFi PW, please check a label on
the bottom panel of your unit.
※ To change the SSID and/or password, move onto Wi-Fi Setup > WiFi
Settings on the web. And change them and click Save.
Maximum wireless signal rate derived from IEEE standard 802.11 specifications. Actual data
throughput and wireless coverage will vary. Network conditions and environmental factors,
including volume of network traffic, building materials and construction, and network overhead,
lower actual data throughput rate and wireless coverage.
7
1. Caution
Please follow the instructions below to avoid physical injury:
You should not install the unit during a storm. Likewise you should not connect or
disconnect any line to avoid the risk of electric shock.
- This unit is indoor use only
- All the communication wirings are limited to inside of the building.
- DO NOT plug in, turn on or attempt to operate an obviously damaged unit.
- Never look directly at the fiber TX port and fiber cable ends when they are
powered on.
- DO NOT use near water.
- DO NOT place near high temperature source.
- DO NOT disassemble the unit.
- DO NOT operate the unit in a location where the maximum ambient
temperature exceeds 45°C.
- Open optical connections must use a protective cap under all circumstances
to protect against physical damage and dirt.
- Before making connections, use isopropyl alcohol and non-fibrous cellulose
to clean the faces of the connectors.
- Avoid impact stresses when handling connectors. Physical damage to the
faces of optical connections impairs transmission quality (higher attenuation).
- Avoid a bend radius in excess of 30 mm for fiber optic links.
- Check the available voltage supply.
- Only use the unit in dry rooms.
- Set up the unit away from direct sunlight or other electrical equipment.
- Only connect approved accessories.
- It may only be repaired by authorized service personnel.
- This equipment is not suitable for use in locations where children are likely
to be present.
Caution & Warning
Limited Warranty
- Not covered under this warranty is defect and damage resulting from product
disassembly by yourself. And also, such behavior may amount to intellectual
property infringement.
1
Information furnished by DASAN Network Solutions is believed to be accurate and reliable. However, no
responsibility is assumed by DASAN Network Solutions for its use, nor for any infringements of patents or
other rights of third parties which may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of DASAN Network Solutions. DASAN Network Solutions reserves the
rights to change specifications at any time without notice.
- H680GM - Power Adapter - RJ45 UTP Cable - QIG (Quick Guide)
2.2 Specification
2.1 Package Contents
2. Introduction
Item Specification
SDRAM 256MB
Flash Memory 128MB
1 GPON port (SC/APC)
Uplink Interface
Service Interface 4 10/100/1000Base-TX ports (RJ45)
2
2.3 Rear View
3
If necessary, you may have your ONT mounted on a wall using mounting holes.
Moun�ng on a Wall
65
2.4 Front View (LED)
4
Dimensions
Power Adapter
Operating Temp.
Output: 12VDC/2A
0 to 45°C (32 to 113°F)
Operating Humidity 0 to 90% (non-condensing)
Wireless
Internal antenna
IEEE 802.11a/b/g/n/ac compliant
Frequency: 2.4GHz, 5GHz
2G band Three Transmit and Three Receive path(3T3R)
5G band Four Transmit and Four Receive path(4T4R)
Item Description
①
ON/OFF button
OPTIC LINE
Turn on/off the unit.
Connect optical network.
Power port Connect an external power supply.
②
RESET button Reboot the unit.
③
USB Connect an external 2.0 USB drive.
④
USB
Connect an external 3.0 USB drive.
⑤
⑥
LAN 1-4
Connect to PC or LAN.
4 10/100/1000Base-TX interfaces
⑦
TEL 1-2 Connect to VoIP phone.
⑧
WLAN
Enable Wi-Fi function.
⑨
WPS
Enable WPS process.
⑩
Operation LEDs
Operating status LEDs.
⑪
TEL
1~2
Green
Hook off.
Green
Hook on.
Blinking
The device has successful 10/100/1000Mbps connections.
Off
Off
The device is sending or receiving data.
LAN
1~4
On
The link is down.
Off
ALM
Red
Green
On No optic signal, firmware update failure or other faults.
Received optical power is normal.
Not in service.
On In service.
WPS
Internet
Green
On
The WLAN is disabled.
Off Disabled or process finished successfully.
WPS in progress.
WPS connection successfully established.
Blinking
2.4/5G
Green
On
On
The device has successful WLAN function.
Off
The device is receiving or sending data.Blinking
Label Light Status
Description
PWR
Green On
Off
Off
Off
The device does not receive power.
The device is receiving power and working properly.
Green
Blinking
USB is connected and working normally.
Off
Data is being transmitted.USB
On
USB is not connected or power is not fed.
The device is linked successfully for optical layer.
PON
Green
On
The device is initializing to an optical network.
The optical link is down.
Blinking
3. Installation
12V 2A
LAN1LAN2LAN3LAN4
TEL2 TEL1
4
5
6
7
2.4GHz
802.11b : 16 dBm ± 1 dB
802.11g : 15 dBm ± 1 dB
802.11n_HT20/40 : 16 dBm ± 1 dB
5GHz
802.11a : 17 dBm ± 1 dB
802.11n/HT20 : 14 dBm ± 1 dB
802.11n/HT40 : 15 dBm ± 1 dB
802.11ac_VHT20/40/80 : 15 dBm ± 1 dB
USB 1 USB 2.0 and 1 USB 3.0
60.3
33.0
201.5mm
214.0
① Flip the device upside down, and slide the stand toward the right and remove it.
② Pull out the protective cap of GPON port.
③ Connect an SC/APC connector optic cable to the GPON port.
And, attach the protective cap and slide the stand onto the device.
④ Connect the telco cable from TEL port
to VoIP phone.
⑤ Connect the Ethernet cable from LAN port
to PC.
⑥ Connect the power cable from power port
to an electrical outlet.
⑦ Turn on the unit by pushing the power button.
GPON Port
2
1
3
11
10
9
12V 2A
LAN1LAN2LAN3LAN4
TEL2 TEL1
1
2
3
4
5
8
6
7
FCC Compliance Statement
Screw
147 mm
Mounting Holes
1
2
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.
CAUTION : Any Changes or modifications not expressly approved by the manufacturer could void
the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
A minimum separation distance of 20 cm must be maintained between the antenna and the person for
this appliance to satisfy the RF exposure requirements.
Enonce d'Industrie Canada(IC)
Le present appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisee aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage,
et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible
d’en compromettre le fonctionnement.
Tout changement ou modification non expressement approuve par la partie chargee de la mise en conformite peut
annuler le droit de l’utilisateur a utiliser l’equipement.
Une distance de séparation minimale de 20 cm doit être maintenue entre l'antenne et la personne pour
que cet appareil satisfasse aux exigences d'exposition aux RF
IC: 3691A-H680GM