Quick Installation Guide DL200 DATA LOGGER V1.
Cellular M2M-IoT Gateway TABLE OF CONTENTS CHAPTER 1 INTRODUCTION .................................................................................................................................. 4 1.1 CONTENTS LIST ............................................................................................................................................. 5 1.2 HARDWARE INSTALLATION .........................................................................................................................
Cellular M2M-IoT Gateway Copyright The contents of this publication may not be reproduced in any part or as a whole, stored, transcribed in an information retrieval system, translated into any language, or transmitted in any form or by any means, mechanical, magnetic, electronic, optical, photocopying, manual, or otherwise, without the prior written permission. Trademarks All products, company, brand names are trademarks or registered trademarks of their respective companies.
Cellular M2M-IoT Gateway Chapter 1 Introduction Congratulations on your purchase of this outstanding product: M2M-IoT Gateway. For M2M (Machine-to-Machine) or IoT (Internet of Thing) applications, AMIT M2M-IoT Gateway is absolutely the right choice. With built-in world-class 3G HSPA+ module, you just need to insert SIM card from local mobile carrier to get to Internet. The redundant SIM design provides a more reliable WAN connection for critical applications.
Cellular M2M-IoT Gateway 1.1 Contents List Items 1 Description Contents DL200 Quantity 1pcs DATA LOGGER 2 3G Antenna 2pcs 3 WiFi Antenna 2pcs Power Adapter 4 1pcs (DC 12V/2A) (*1) 5 RJ45 Cable 1pcs 6 RS485 Cable 1pcs 7 Wall Mount Kits 2pcs 8 DIN-Rail Bracket 1pcs 9 USB flash drive Mfg: SanDick Type: SDCZ33 (8GB ) 1pcs 1 The maximum power consumption of IOG761-0P001 is 15.5W.
Cellular M2M-IoT Gateway Hardware Installation 1.2.1 WARNING Do not use the product in high humidity or high temperatures. Do not connect AC power to this device directly. This product accepts DC power voltage from 9V to 48V. Using a different voltage rating power source will damage the router. Do not open or repair the case by yourself. If the Attention Product is too hot, turn off the power immediately and have it repaired at a qualified service center.
Cellular M2M-IoT Gateway FCC Caution: Any changes or modifications not expressly approved by the party responsi for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Cellular M2M-IoT Gateway 1.2.2 SYSTEM REQUIREMENTS Network Requirements An Ethernet RJ-45 cable or DSL modem 3G cellular service subscription IEEE 802.11n or 802.11b/ g wireless clients 10/100 Ethernet adapter on PC Computer with the following: Windows® , Macintosh, or Linux-based operating system An installed Ethernet adapter Browser Requirements: Web-based Configuration Utility Requirements Internet Explorer 6.0 or higher Chrome 2.0 or higher Firefox 3.
Cellular M2M-IoT Gateway 1.2.3 Hardware Configuration LED Indicators 3G Antenna USB Port Auto MDI/MDIX RJ-45 Ports 4x FE LAN to connect local devices RS 485 Port Console Port Reset Button 3G Antenna ※Reset Button The RESET button provides user with a quick and easy way to resort the default setting. Press the RESET button continuously for 6 sec, and then release it. The device will restore to factory default settings.
Cellular M2M-IoT Gateway 2.4G WiFi Antenna 2.
Cellular M2M-IoT Gateway 1.2.
Cellular M2M-IoT Gateway Chapter 2 Getting Started This chapter describes how to install and configure the hardware and how to use the set-up wizard to configure the network with the web GUI of IOG761 series. 2.1 Hardware Installation 2.1.1 Mount the Unit The IOG761 series can be placed on a desktop, mounted on the wall, or mounted on a DIN-rail. It has designed with “ears” for attaching to the wall or the inside of a cabinet.
Cellular M2M-IoT Gateway 2.1.3 Connecting Power The IOG761 series can be powered by connecting a power source to the terminal block. It supports dual 12VDC power inputs, 30VDC digital input and output 3. Following picture is the power terminal block pin assignments. Please check carefully and connect to the right power requirements and polarity. PWR1 GND PWR2 GND DI+ DI- DO+ DO- There are a DC12V/2A power adapter in the package for you to easily connect DC power adapter to this terminal block. 2.
Cellular M2M-IoT Gateway 2.1.5 Connecting Serial Devices The IOG761 provides one standard serial port DB-9 male connector. Connect the serial device to the unit DB-9 male port with the right pin assignments of RS-232/485 are shown as below.
Cellular M2M-IoT Gateway 2.1.6 Connecting to the Network or a Host The IOG761 series provides four RJ-45 ports to connect 10/100Mbps Ethernet. It can auto detect the transmission speed on the network and configure itself automatically. Connect the Ethernet cable to the RJ-45 ports of the device. Plug one end of an Ethernet cable into your computer’s network port and the other end into one of IOG761 series for LAN ports on the front panel.
Cellular M2M-IoT Gateway 2.2 Easy Setup by Configuring WEB UI You can browse web UI to configure the device. First you need to launch the Setup Wizard browser and then the Setup Wizard will guide you step-by-step to finish the setup process. Browse and Activate the Setup Wizard Type in the IP Address (http://192.168.123.254)4 When you see the login page, type the password ‘admin’ 5 and then click ‘login’ button. After login, Select your language from the list.
Cellular M2M-IoT Gateway Press “Next” to start the Setup Wizard. Configure with the Setup Wizard Step 1 You can change the login password of web UI here. It’s strongly recommending you to change this login password from default value. Step 2 Select Time Zone. Step 3 You can select Auto detecting WAN type or setup WAN type manually.
Cellular M2M-IoT Gateway Step 4 If selecting Auto Detecting WAN type, the system will start to detect the WAN type automatically. The next page will show result of WAN detection in your environment. If the result is not exactly what you need, you can still choose other WAN type here. You can also change LAN IP address of this gateway here. Step 5 Type in Host name and ISP registered MAC address. If you don’t have such information, you can keep in blank and go to next page. Step 5-1 Wi-Fi settings.
Cellular M2M-IoT Gateway Step 5-2 Wi-Fi authentication and encryption settings. It’s strongly recommending you to add authentication and encryption in your wireless network to prevent any unknown Wi-Fi clients connecting to your wireless network and keep transferred data secured. Step 6 Check the information again. If all settings are correct, please press “Apply Settings” button to save new settings. Then it will take 70 seconds to take new settings effective. Step 7 Configuration is completed.
Cellular M2M-IoT Gateway Select “Darfon” for Show All of Micro Inverter status in the monitor system. Press “Micro Inverter” to start the Micro Inverter status view.
